Med Temp Extended Run Time Pack Material Safety Data Sheet P/N 0103-350-017 QUICK IDENTIFIER (See Section 1)

SECTION 1- IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING

Identification of the Substances or Preparation

Product: Med Temp Extended Run Time Pack, P/N 0103-350-017

Synonyms: None

Chemical Blend of Lignosulfonate and polymers Family:

Blend of cement retarder, fluid loss additive, and cement dispersant used to extend the allowable time Application: from mixing to dumping of cement slurry to 3½ – 4 hrs

NeoProducts, LLC Manufacturer’s name:

1201 Dealers Ave. Emergency Telephone #: 504-731-1011 Address:

Harahan, LA 70123 e-mail: [email protected] City, State, Zip:

After hours calls will be answered by answering service. Signature of JV Carisella person responsible for preparation Date Prepared: January 2012 (Optional):

SECTION 2- HAZARD IDENTIFICATION

Risk Phrases: N/A

Hazard May cause eye and respiratory irritation. Airborne dust may be explosive. Overview: SECTION 3- COMPOSITION/INFORMATION ON INGREDIENTS

Time Weighted Time Weighted Component(s) % OPT. Average Average CAS No. [chemical and common name(s)] (inhalable dust) (respirable dust) 8061-51-6 Cement Slurry Retarder, DTI #2117 77.0 – 82.0 N/A N/A wgt %

Suspension Agent, DTI #2099 12.5 – 16.0 N/A N/A wgt % 9084-06-4 Friction Reducer, DTI #4244 5.5 – 10.5 N/A N/A wgt %

SECTION 4- FIRST AID MEASURES

If inhaled, remove from area to fresh air. Get medical attention if respiratory irritation develops or if breathing Inhalation: becomes difficult.

Ingestion: Do not induce vomiting. Slowly dilute with 1-2 glasses of water or milk and seek medical attention. Never give anything by mouth to an unconscious person.

Skin: Wash with soap and water.

Eyes: In case of contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical attention if irritation persists.

Notes to physician N/A

SECTION 5- FIRE FIGHTING MEASURES

Suitable Extinguishing media: Water fog, carbon dioxide, foam, dry chemical.

Unsuitable Extinguishing media: None known.

Special Exposure Hazards: Decomposition in fire may produce toxic gases. Organic dust in the presence of an ignition source can be explosive in high concentrations. Good housekeeping practices are required to minimize this potential.

Special protective equipment for fire- Full protective clothing and NIOSH-approved self-contained breathing apparatus fighters: with full facepiece required for fire fighting personnel. SECTION 6- ACCIDENTAL RELEASE MEASURES

Personal precautionary Use appropriate protective equipment. measures:

Environmental None known. precautionary measures: Scoop up and remove. Procedure for cleaning/absorption:

SECTION 7- HANDLING AND STORAGE

Handling precautions: Avoid contact with skin and eyes. Avoid creating or inhaling dust. Avoid dust accumulations.

Storage Information: Keep container closed when not in use. Keep from freezing. Product has a shelf life of 24 months.

SECTION 8- EXPOSURE CONTROLS/ PERSONAL PROTECTION

Engineering controls: Use in a well ventilated area.

Respiratory protection: Not normally necessary.

Hand protection: Use normal work gloves.

Skin protection: Normal work coveralls.

Eye protection: Chemical goggles; also wear a face shield if splashing hazard exists.

Other precautions: None known.

SECTION 9- PHYSICAL AND CHEMICAL PROPERTIES

Physical State: Color: Odor: PH : Molecular Weight (g/mole): Powder Brown Slight 5.0 (+/-1) @ 10 % Not Determined

Vapor Density Decomposition Vapor Pressure @ Specific Gravity @ Percent volatiles :

(Air=1): Temperature (C): 20 C (mm HG): 20C (H2O=1):

Not Determined Not Determined Not Determined 0.55 Not Determined Flash Point/Range Flash Point Method: Pour point/Range Freezing Boiling Point/Range (C): (C): Point/Range (C): (C):

Not Determined Not Determined Not Determined >130 Not Determined Bulk Density @ 20C Autoignition Flammable Limits in Flammable Limits in Density @ 20C (kg/m3): temperature (C): Air – Lower (g/m3): Air – Lower (%): (kg/l):

Not Determined 550 >150 Not Determined Not Determined Flammable Limits in Flammable Limits in Evaporation Rate Solubility in Water Solubility in Air – Upper (g/m3): Air – Upper (%): (Butyl Acetate=1): (g/100ml): Solvents (g/100ml):

Not Determined Not Determined Not Determined Soluble Not Determined

VOCs (g/l): Viscosity, Dynamic Viscosity, Kinematic Partition @ 20 C (centipoise): @ 20 C Coefficient/n- (centistrokes): Octanol/Water: Not Determined Not Determined Not Determined Not Determined

SECTION 10- STABILITY AND REACTIVITY

Stability Hazardous Conditions Incompatibility Hazardous Decomposition Additional Data: Polymerization: to avoid: (Materials to or Byproducts: Guidelines: avoid): Oxides of sulfur. Carbon N/A Stable Will not occur None Strong oxidizers monoxide and carbon known dioxide.

SECTION 11- TOXICOLOGICAL INFORMATION

Principle route of exposure: Eye or skin contact, inhalation.

Inhalation: None known.

Skin Contact: Not irritating to skin in rabbits.

Eye Contact: May cause mild eye irritation.

Ingestion: None known.

Medical conditions aggravated by exposure: None known. No data available to indicate product or components present at greater Chronic effects/ Carcinogenicity: than 1% are chronic health hazards. None known. Other Information

Toxicity Tests:

Oral Toxicity: LD50: > 15000 mg/kg (Rat)

Dermal Toxicity: Not Determined

Inhalation Toxicity: Not Determined

Primary Irritation Effect: Not Determined

Carcinogenicity: Not Determined Genotoxicity: Not Determined

Reproductive/Developmental Toxicity: Not Determined

SECTION 12- ECOLOGICAL INFORMATION

Mobility (water/air/soil): Not Determined

Persistence/ Degradability: Inherently biodegradable.

Bio-Accumulation: N/A

Ecotoxicological Information:

Acute Fish Toxicity: Not classified as toxic to fish (OECD 203)

Acute Crustaceans TLM96: > 3300 ppm (Crangon crangon) Toxicity:

Acute Algae Toxicity: Not Determined

Chemical Fate Information: Not Determined

Other Information: N/A

SECTION 13- DISPOSAL CONSIDERATIONS

Disposal Method: Bury in a licensed landfill according to local regulations.

Contaminated Packaging: Follow all applicable national or local regulations.

SECTION 14- TRANSPORT INFORMATION

Land Transportation: ADR – Not restricted

Air Transportation: ICAO/IATA – Not restricted

Sea Transportation: IMDG – Not restricted

Other Shipping Information: Labels: None

SECTION 15- REGULATORY INFORMATION EC Supply labeling This product is not subject to the labeling requirements of EC Directives 67/548/EEC and Requirements: 88/379/EEC as amended.

Classification: Not classified

Risk Phrases: None.

Safety Phrases: None.

EINECS inventory This product, and all its components, complies with EINECS Germany, Water WGK 1: Low hazard to waters. Endangering Classes (WGK)

SECTION 16- ADDITIONAL INFORMATION:

This product is intended for the stated application only. Do not use this product for any other applications without first obtaining guidance from an approved NeoProducts representative, beforehand.

If this product is for resale, make sure the purchaser receives a copy of this safety data sheet upon acceptance of this preparation. Make sure the employees of your company are aware of the hazards, both chronic and acute, before allowing them to use this product.

The information contained in this Material Safety Data Sheet is believed to be correct and reflects our best professional judgment. Because it is impossible to anticipate every condition under which this product will be used, this Material Safety Data Sheet shall only be used as a guide. It is imperative that each user of this product determines its suitability for his particular application and comply with all environmental and workplace regulations.

Disclaimer Statement:

This information is furnished without warranty, expressed or implied, as to accuracy or completeness. The information is obtained from various sources including the manufacturer and other third party sources. The information may not be valid under all conditions nor if this material is used in combination with other materials or in any process. Final determination of suitability of any material is the sole responsibility of the user.