Cabinet and Drawer Hardware
Total Page：16
File Type：pdf, Size：1020Kb
SECTION 06 41 20 CABINET AND DRAWER HARDWARE
Display hidden notes to specifier. (Don't know how? Click Here)
Copyright 2007 - 2015 ARCAT, Inc. - All rights reserved
1 GENERAL
1.1 SECTION INCLUDES
1.1.1 Cabinet and drawer hardware of the following types: 1.1.1.1 Lift systems. 1.1.1.2 Concealed hinge systems. 1.1.1.3 Drawer runner systems. 1.1.1.4 Box systems. 1.1.1.5 Electronic opening systems.
1.2 RELATED SECTIONS
1.2.1 Section 06 41 13 - Wood-Veneer-Faced Architectural Cabinets.
1.2.2 Section 08 81 00 - Glass Glazing.
1.2.3 Section 12 32 16 - Manufactured Plastic-Laminate-Clad Casework.
1.2.4 Section 26 05 00 - Common Work Results for Electrical.
1.3 REFERENCES
1.3.1 ANSI/BHMA - Meets Grade 1 - drawer runner systems. Grade 2 - hinge systems. Requirements for cycle life, static load and self-closing performance.
1.4 SUBMITTALS
1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.
1.4.2 06 41 20-1 Product Data: Manufacturer's data sheets on each product to be used, including: 1.4.2.1 Preparation instructions and recommendations. 1.4.2.2 Storage and handling requirements and recommendations. 1.4.2.3 Installation methods.
1.4.3 Verification Samples: For each finish specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.
1.5 QUALITY ASSURANCE
1.5.1 Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and function. 1.5.1.1 Do not proceed with remaining work until mock-up is approved by Architect. 1.5.1.2 Remodel mock-up area as required to produce acceptable work.
1.6 DELIVERY, STORAGE, AND HANDLING
1.6.1 Store products in manufacturer's unopened packaging until ready for installation.
1.7 PROJECT CONDITIONS
1.7.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.
1.8 PRE-INSTALLATION MEETINGS
1.8.1 Convene minimum two weeks prior to starting work of this section.
1.9 SEQUENCING
1.9.1 Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.
2 PRODUCTS
2.1 MANUFACTURERS
2.1.1 Acceptable Manufacturer: Blum, Inc., which is located at: 7733 Old Plank Rd.; Stanley, NC 28164; Toll Free Tel: 800-438-6788; Tel: 704-827-1345; Fax: 704-827-0799; Email: request info ([email protected]); Web: www.blum.com | www.dynamicspace.us
2.1.2 Substitutions: Not permitted.
2.1.3 06 41 20-2 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.
2.2 LIFT SYSTEMS
2.2.1 Approved Product: Blum AVENTOS HF bi-fold lift system 2.2.1.1 Cabinet Construction: 2.2.1.1.1 Face frame for the following application: 2.2.1.1.1.1 Wood door. 2.2.1.1.1.2 Wide aluminum frame door. 2.2.1.1.2 Frameless for the following application: 2.2.1.1.2.1 Wood door. 2.2.1.1.2.2 Wide aluminum frame door. 2.2.1.1.2.3 Narrow aluminum frame door. 2.2.1.2 Lift type: 2.2.1.2.1 Bi-fold lift mechanism 2.2.1.2.2 Bi-fold lift mechanism with SERVO-DRIVE: Electric opening of the door with just a light touch of the front. 2.2.1.3 Cabinet Height Range: 2.2.1.3.1 18-7/8 inches (479 mm) - 42 inches (1067 mm). 2.2.1.4 Cabinet Width Range: 2.2.1.4.1 15 inches (381 mm) - 72 inches (1828 mm). 2.2.1.5 Dampening System: Self-regulates the closing speed of the door. 2.2.1.5.1 Integrated. 2.2.1.6 Mounting: 2.2.1.6.1 Screw-on. 2.2.1.7 Accessories: 2.2.1.7.1 Angle restriction clip: Part No. ______2.2.1.7.2 SERVO-DRIVE: Electric opening of the door with just a light touch of the front.
2.2.2 Approved Product: Blum AVENTOS HS up and over lift system. 2.2.2.1 Cabinet Construction: 2.2.2.1.1 Face frame for the following application: 2.2.2.1.1.1 Wood door. 06 41 20-3 2.2.2.1.1.2 Wide aluminum frame door. 2.2.2.1.2 Frameless for the following application: 2.2.2.1.2.1 Wood door. 2.2.2.1.2.2 Wide aluminum frame door. 2.2.2.1.2.3 Narrow aluminum frame door. 2.2.2.2 Lift type: 2.2.2.2.1 Up and over lift mechanism. 2.2.2.2.2 Up and over lift mechanism with SERVO-DRIVE: Electric opening of the door with just a light touch of the front. 2.2.2.3 Cabinet Height Range: 2.2.2.3.1 13-3/4 inches (350 mm) - 31-1/2 inches (800 mm). 2.2.2.4 Cabinet Width Range: 2.2.2.4.1 15 inches (381 mm) - 72 inches (1828 mm). 2.2.2.5 Dampening System: Self-regulates the closing speed of the door 2.2.2.5.1 Integrated. 2.2.2.6 Mounting: 2.2.2.6.1 Screw-on. 2.2.2.7 Accessories: 2.2.2.7.1 SERVO-DRIVE: Electric opening of the door with just a light touch of the front.
2.2.3 Approved Product: Blum AVENTOS HL lift up lift system. 2.2.3.1 Cabinet Construction: 2.2.3.1.1 Face frame for the following application: 2.2.3.1.1.1 Wood door. 2.2.3.1.1.2 Wide aluminum frame door. 2.2.3.1.2 Frameless for the following application: 2.2.3.1.2.1 Wood door. 2.2.3.1.2.2 Wide aluminum frame door. 2.2.3.1.2.3 Narrow aluminum frame door. 2.2.3.2 Lift Type: 2.2.3.2.1 Lift up lift mechanism. 2.2.3.2.2 Lift up lift mechanism with SERVO-DRIVE: Electric opening of the door with 06 41 20-4 just a light touch of the front. 2.2.3.3 Cabinet Height Range: 2.2.3.3.1 11-13/16 inches (300 mm) - 22-13/16 inches (580 mm). 2.2.3.3.2 Appliance garage application: 17-11/16 inches (450 mm) - 22-13/16 inches (580 mm) 2.2.3.4 Cabinet Width Range: 2.2.3.4.1 15 inches (381 mm) - 72 inches (1828 mm). 2.2.3.5 Dampening System: Self-regulates the closing speed of the door 2.2.3.5.1 Integrated. 2.2.3.6 Mounting: 2.2.3.6.1 Screw-on. 2.2.3.7 Accessories: 2.2.3.7.1 SERVO-DRIVE: Electric opening of the door with just a light touch of the front
2.2.4 Approved Product: Blum AVENTOS HK stay lift system. 2.2.4.1 Cabinet Construction: 2.2.4.1.1 Face frame for the following application: 2.2.4.1.1.1 Wood door. 2.2.4.1.1.2 Wide aluminum frame door. 2.2.4.1.2 Frameless for the following application: 2.2.4.1.2.1 Wood door. 2.2.4.1.2.2 Wide aluminum frame door. 2.2.4.1.2.3 Narrow aluminum frame door. 2.2.4.2 Lift Type: 2.2.4.2.1 Stay lift mechanism. 2.2.4.2.2 Stay lift mechanism with SERVO-DRIVE: Electric opening of the door with just a light touch of the front. 2.2.4.2.3 Stay lift mechanism with TIP-ON: Mechanical opening of the door with just a light touch of the front 2.2.4.3 Cabinet Height Range: 2.2.4.3.1 11-13/16 inches (300 mm) - 24 inches (610 mm). 2.2.4.4 Cabinet Width Range: 2.2.4.4.1 15 inches (381 mm) - 72 inches (1828 mm). 2.2.4.5 06 41 20-5 Dampening System: Self-regulates the closing speed of the door 2.2.4.5.1 Integrated. 2.2.4.6 Mounting: 2.2.4.6.1 Screw-on. 2.2.4.7 Accessories: 2.2.4.7.1 Angle restriction clip: Part No. ______2.2.4.7.2 SERVO-DRIVE: Electric opening of the door with just a light touch of the front 2.2.4.7.3 TIP-ON: Mechanical opening of the door with just a light touch of the front
2.2.5 Approved Product: Blum AVENTOS HK-S stay lift system 2.2.5.1 Cabinet Construction: 2.2.5.1.1 Face frame for the following application: 2.2.5.1.1.1 Wood door. 2.2.5.1.1.2 Wide aluminum frame door. 2.2.5.1.2 Frameless for the following application: 2.2.5.1.2.1 Wood door. 2.2.5.1.2.2 Wide aluminum frame door. 2.2.5.1.2.3 Narrow aluminum frame door. 2.2.5.2 Lift Type: 2.2.5.2.1 Stay lift mechanism. 2.2.5.2.2 Stay lift mechanism with TIP-ON: Mechanical opening of the door with just a light touch of the front. 2.2.5.3 Cabinet Height Range: 2.2.5.3.1 7-3/8 inches (186 mm) - 24 inches (610 mm). 2.2.5.4 Cabinet Width Range: 2.2.5.4.1 15 inches (381 mm) - 72 inches (1828 mm). 2.2.5.5 Dampening System: Self-regulates the closing speed of the door 2.2.5.5.1 Integrated. 2.2.5.6 Mounting: 2.2.5.6.1 Screw-on. 2.2.5.7 Accessories: 2.2.5.7.1 Angle restriction clip: Part No. ______2.2.5.7.2 06 41 20-6 TIP-ON: Mechanical opening of the door with just a light touch of the front
2.2.6 Approved Product: Blum AVENTOS HK-XS smaller stay lift system 2.2.6.1 Cabinet Construction: 2.2.6.1.1 Face frame for the following application: 2.2.6.1.1.1 Wood door. 2.2.6.1.1.2 Wide aluminum frame door. 2.2.6.1.2 Frameless for the following application: 2.2.6.1.2.1 Wood door. 2.2.6.1.2.2 Wide aluminum frame door. 2.2.6.1.2.3 Narrow aluminum frame door. 2.2.6.2 Lift Type: 2.2.6.2.1 Smaller stay lift mechanism. 2.2.6.2.2 Stay lift mechanism with TIP-ON: Mechanical opening of the door with just a light touch of the front 2.2.6.3 Cabinet Height Range: 2.2.6.3.1 9-3/8 inches (238 mm) - 24 inches (610 mm). 2.2.6.4 Cabinet Width Range: 2.2.6.4.1 9 inches (229 mm) - 72 inches (1828 mm). 2.2.6.5 Dampening System: Self-regulates the closing speed of the door 2.2.6.5.1 Integrated. 2.2.6.6 Mounting: 2.2.6.6.1 Screw-on. 2.2.6.7 Accessories: 2.2.6.7.1 Angle restriction clip: Part No. ______. 2.2.6.7.2 TIP-ON: Mechanical opening of the door with just a light touch of the front
2.3 CONCEALED HINGE SYSTEMS
2.3.1 Approved Product: Blum CLIP top Angled Hinges 2.3.1.1 Cabinet Construction: 2.3.1.1.1 Frameless for the following application: 2.3.1.1.1.1 Full overlay. 2.3.1.1.1.2 06 41 20-7 Partial overlay. 2.3.1.1.1.3 Corner merge. 2.3.1.1.1.4 Inset. 2.3.1.1.1.5 Mitered corner. 2.3.1.2 Hinge Type: 2.3.1.2.1 Angled hinge. 2.3.1.3 Angle: 2.3.1.3.1 Plus 15 degree. 2.3.1.3.2 Plus 20 degree. 2.3.1.3.3 Plus 30 degree II. 2.3.1.3.4 Plus 30 degree III. 2.3.1.3.5 Plus 45 degree I. 2.3.1.3.6 Plus 45 degree II. 2.3.1.3.7 Plus 45 degree III. 2.3.1.3.8 Minus 15 degree. 2.3.1.3.9 Minus 30 degree. 2.3.1.3.10 Minus 45 degree. 2.3.1.3.11 95 degree: Straight-arm. 2.3.1.3.12 95 degree: Half-cranked. 2.3.1.3.13 95 degree: Full-cranked. 2.3.1.4 Suitable for Door Type: 2.3.1.4.1 For 19 mm (3/4 inch) door thickness, material consist of wood, melamine, MDF or particleboard. 2.3.1.5 Closing: 2.3.1.5.1 Self-close. 2.3.1.6 Dampening System: Self-regulates the closing speed of the hinge 2.3.1.6.1 Approved Product: BLUMOTION 970A. 2.3.1.7 Mounting: 2.3.1.7.1 INSERTA, tool-free assembly. 2.3.1.8 Hinges per Door: 2.3.1.8.1 2 hinges for doors less than 36 inches (914 mm) high and less than 15 lb (7 kg). 2.3.1.8.2 06 41 20-8 3 hinges for doors less than 64 inches (1626 mm) high and less than 30 lb (14 kg). 2.3.1.8.3 4 hinges for doors less than 86 inches (2184 mm) high and less than 45 lb (20 kg). 2.3.1.8.4 5 hinges for doors less than 96 inches (2438 mm) high and less than 60 lb (27 kg). 2.3.1.8.5 The distance between the top and bottom hinge must be greater than the width of the door. 2.3.1.9 Cover Caps: 2.3.1.9.1 Nickel plated steel. 2.3.1.9.2 Nickel plated steel with Blum logo (embossed). 2.3.1.9.3 Nickel plated steel with custom logo (minimums apply).
2.3.2 Approved Product: Blum CLIP top BLUMOTION Angled Hinges. 2.3.2.1 Cabinet Construction: 2.3.2.1.1 Frameless for the following application: 2.3.2.1.1.1 Full overlay 2.3.2.1.1.2 Partial overlay 2.3.2.1.1.3 Corner merge 2.3.2.1.1.4 Inset 2.3.2.1.1.5 Mitered corner 2.3.2.2 Hinge Type: 2.3.2.2.1 Angled hinge. 2.3.2.3 Angle: 2.3.2.3.1 Plus 15 degree. 2.3.2.3.2 Plus 20 degree. 2.3.2.3.3 Plus 30 degree II. 2.3.2.3.4 Plus 30 degree III. 2.3.2.3.5 Plus 45 degree I. 2.3.2.3.6 Plus 45 degree II. 2.3.2.3.7 Plus 45 degree III. 2.3.2.3.8 Minus 15 degree. 2.3.2.3.9 Minus 30 degree. 2.3.2.3.10 Minus 45 degree. 06 41 20-9 2.3.2.3.11 95 degree: Straight-arm. 2.3.2.3.12 95 degree: Half-cranked. 2.3.2.3.13 95 degree: Full-cranked. 2.3.2.4 Suitable for Door Type: 2.3.2.4.1 For 19 mm (3/4 inch) door thickness, material consist of wood, melamine, MDF or particleboard. 2.3.2.5 Closing: 2.3.2.5.1 Soft close. 2.3.2.6 Dampening System: Self-regulates the closing speed of the hinge 2.3.2.6.1 Integrated into hinge. 2.3.2.7 Mounting: 2.3.2.7.1 INSERTA, tool-free assembly. 2.3.2.8 Hinges per Door: 2.3.2.8.1 2 hinges for doors less than 36 inches (914 mm) high and less than 15 lb (7 kg). 2.3.2.8.2 3 hinges for doors less than 64 inches (1626 mm) high and less than 30 lb (14 kg). 2.3.2.8.3 4 hinges for doors less than 86 inches (2184 mm) high and less than 45 lb (20 kg). 2.3.2.8.4 5 hinges for doors less than 96 inches (2438 mm) high and less than 60 lb (27 kg). 2.3.2.8.5 The distance between the top and bottom hinge must be greater than the width of the door. 2.3.2.9 Cover Caps: 2.3.2.9.1 Nickel plated steel. 2.3.2.9.2 Nickel plated steel with Blum logo (embossed). 2.3.2.9.3 Nickel plated steel with custom logo (minimums apply).
2.3.3 Approved Product: Blum CLIP top Concealed Hinges. 2.3.3.1 Cabinet Construction: 2.3.3.1.1 Face frame for the following application: 2.3.3.1.1.1 Full overlay. 2.3.3.1.1.2 Partial overlay. 2.3.3.1.1.3 Twin overlay. 2.3.3.1.1.4 06 41 20-10 Inset. 2.3.3.1.1.5 Inset and overlay corner. 2.3.3.1.1.6 Flush door. 2.3.3.1.2 Frameless for the following application: 2.3.3.1.2.1 Full overlay. 2.3.3.1.2.2 Partial overlay. 2.3.3.1.2.3 Twin overlay. 2.3.3.1.2.4 Inset. 2.3.3.1.2.5 Inset and overlay corner. 2.3.3.1.2.6 Flush door. 2.3.3.2 Hinge Type: 2.3.3.2.1 Straight-arm. 2.3.3.2.2 Half-cranked. 2.3.3.2.3 Full-cranked. 2.3.3.2.4 Thick door. 2.3.3.2.5 Wide angled. 2.3.3.2.6 Zero protrusion. 2.3.3.2.7 Inset blind corner. 2.3.3.2.8 Overlay blind corner. 2.3.3.2.9 Aluminum door. 2.3.3.2.10 Diagonal 45 degree. 2.3.3.2.11 Mini. 2.3.3.2.12 Glass. 2.3.3.2.13 Bi-fold. 2.3.3.2.14 Angled. 2.3.3.2.15 Special applications. 2.3.3.3 Angle: 2.3.3.3.1 107 degree. 2.3.3.3.2 110 degree. 2.3.3.3.3 110 plus degree. 2.3.3.3.4 120 degree. 2.3.3.3.5 06 41 20-11 120 plus degree. 2.3.3.3.6 95 degree thick door. 2.3.3.3.7 170 degree. 2.3.3.3.8 170 degree special applications. 2.3.3.3.9 155 degree zero protrusion. 2.3.3.3.10 155 degree special applications. 2.3.3.3.11 125 degree zero protrusion. 2.3.3.3.12 125 degree special applications. 2.3.3.3.13 95 degree inset blind corner. 2.3.3.3.14 95 degree overlay blind corner. 2.3.3.3.15 120 degree aluminum door for BLUMOTION. 2.3.3.3.16 120 degree aluminum door. 2.3.3.3.17 110 degree diagonal 45 degree. 2.3.3.3.18 95 degree mini. 2.3.3.3.19 95 degree glass door. 2.3.3.3.20 60 degree bi-fold. 2.3.3.3.21 95 degree / 110 degree angled. 2.3.3.4 Suitable for Door Type: 2.3.3.4.1 For door thickness range 16 mm to 30 mm, material consist of wood, melamine, MDF or particleboard. 2.3.3.5 Closing: 2.3.3.5.1 Self-close. 2.3.3.5.2 Free swing. 2.3.3.6 Dampening System: Self-regulates the closing speed of the hinge. 2.3.3.6.1 Approved Product: BLUMOTION 973A. 2.3.3.6.2 Approved Product: BLUMOTION 971A. 2.3.3.6.3 Approved Product: BLUMOTION 970A. 2.3.3.7 Mounting: 2.3.3.7.1 Screw-on. 2.3.3.7.2 Press-in. 2.3.3.7.3 INSERTA, tool-free assembly. 2.3.3.7.4 EXPANDO. 06 41 20-12 2.3.3.8 Hinges per Door: 2.3.3.8.1 2 hinges for doors less than 36 inches (914 mm) high and less than 15 lb (7 kg). 2.3.3.8.2 3 hinges for doors less than 64 inches (1626 mm) high and less than 30 lb (14 kg). 2.3.3.8.3 4 hinges for doors less than 86 inches (2184 mm) high and less than 45 lb (20 kg). 2.3.3.8.4 5 hinges for doors less than 96 inches (2438 mm) high and less than 60 lb (27 kg). 2.3.3.8.5 The distance between the top and bottom hinge must be greater than the width of the door. 2.3.3.9 Cover Caps: 2.3.3.9.1 Nylon: Black. 2.3.3.9.2 Nylon: Black with custom logo (minimums apply). 2.3.3.9.3 Nylon: White. 2.3.3.9.4 Nylon: White with custom logo (minimums apply). 2.3.3.9.5 Nickel plated steel. 2.3.3.9.6 Nickel plated steel with Blum logo (embossed). 2.3.3.9.7 Nickel plated steel with custom logo (minimums apply).
2.3.4 Approved Product: Blum CLIP top BLUMOTION Hinges. Concealed hinges with integrated soft close. 2.3.4.1 Cabinet Construction: 2.3.4.1.1 Face frame for the following application: 2.3.4.1.1.1 Full overlay. 2.3.4.1.1.2 Partial overlay. 2.3.4.1.1.3 Twin overlay. 2.3.4.1.1.4 Inset. 2.3.4.1.1.5 Inset and overlay corner. 2.3.4.1.1.6 Flush door. 2.3.4.1.2 Frameless for the following application: 2.3.4.1.2.1 Full overlay. 2.3.4.1.2.2 Partial overlay. 2.3.4.1.2.3 Twin overlay. 2.3.4.1.2.4 06 41 20-13 Inset. 2.3.4.1.2.5 Inset and overlay corner. 2.3.4.1.2.6 Flush door. 2.3.4.2 Hinge Type: 2.3.4.2.1 Straight-arm. 2.3.4.2.2 Half-cranked. 2.3.4.2.3 Full-cranked. 2.3.4.2.4 Thick door. 2.3.4.2.5 Diagonal 45 degree. 2.3.4.2.6 Inset blind corner. 2.3.4.2.7 Overlay blind corner. 2.3.4.2.8 Narrow aluminum door. 2.3.4.2.9 Angled 2.3.4.3 Angle: 2.3.4.3.1 110 degree. 2.3.4.3.2 110 plus degree. 2.3.4.3.3 95 degree thick door. 2.3.4.3.4 110 degree diagonal 45 degree. 2.3.4.3.5 95 degree inset blind corner. 2.3.4.3.6 95 degree overlay blind corner. 2.3.4.3.7 95 degree narrow aluminum door. 2.3.4.4 Suitable for Door Type: 2.3.4.4.1 For door thickness range 16 mm to 30 mm, material consist of wood, melamine, MDF or particleboard. 2.3.4.5 Closing: 2.3.4.5.1 Soft close. 2.3.4.6 Dampening System: Self-regulates the closing speed of the hinge 2.3.4.6.1 Integrated into hinge. 2.3.4.7 Mounting: 2.3.4.7.1 Screw-on. 2.3.4.7.2 Press-in. 2.3.4.7.3 INSERTA, tool-free assembly. 06 41 20-14 2.3.4.7.4 EXPANDO. 2.3.4.8 Hinges per Door: 2.3.4.8.1 2 hinges for doors less than 36 inches (914 mm) high and less than 15 lb (7 kg). 2.3.4.8.2 3 hinges for doors less than 64 inches (1626 mm) high and less than 30 lb (14 kg). 2.3.4.8.3 4 hinges for doors less than 86 inches (2184 mm) high and less than 45 lb (20 kg). 2.3.4.8.4 5 hinges for doors less than 96 inches (2438 mm) high and less than 60 lb (27 kg). 2.3.4.8.5 The distance between the top and bottom hinge must be greater than the width of the door 2.3.4.9 Cover Caps: 2.3.4.9.1 Nylon: Black. 2.3.4.9.2 Nylon: Black with custom logo (minimums apply). 2.3.4.9.3 Nylon: White. 2.3.4.9.4 Nylon: White with custom logo (minimums apply). 2.3.4.9.5 Nickel plated steel. 2.3.4.9.6 Nickel plated steel with Blum logo (embossed). 2.3.4.9.7 Nickel plated steel with custom logo (minimums apply).
2.3.5 Approved Product: Blum CLIP top Glass Door Hinges. 2.3.5.1 Cabinet Construction: 2.3.5.1.1 Frameless for the following application: 2.3.5.1.1.1 Full overlay. 2.3.5.1.1.2 Partial overlay. 2.3.5.1.1.3 Inset. 2.3.5.2 Hinge Type: 2.3.5.2.1 Straight-arm. 2.3.5.2.2 Half-cranked. 2.3.5.2.3 Full-cranked. 2.3.5.3 Angle: 2.3.5.3.1 95 degree: Straight-arm. 2.3.5.3.2 95 degree: Half-cranked. 06 41 20-15 2.3.5.3.3 95 degree: Full-cranked. 2.3.5.4 Suitable for Door Type: 2.3.5.4.1 For glass thickness of 4.5 mm to 7 mm. 2.3.5.5 Closing: 2.3.5.5.1 Self-close. 2.3.5.6 Dampening System: Self-regulates the closing speed of the hinge 2.3.5.6.1 Approved Product: BLUMOTION 971A. 2.3.5.6.2 Approved Product: BLUMOTION 970A. 2.3.5.7 Mounting: Screw-on. 2.3.5.8 Hinges per Door: 2.3.5.8.1 2 hinges for doors less than 36 inches (914 mm) high and less than 15 lb (7 kg). 2.3.5.8.2 3 hinges for doors less than 64 inches (1626 mm) high and less than 30 lb (14 kg). 2.3.5.8.3 4 hinges for doors less than 86 inches (2184 mm) high and less than 45 lb (20 kg). 2.3.5.8.4 5 hinges for doors less than 96 inches (2438 mm) high and less than 60 lb (27 kg). 2.3.5.8.5 The distance between the top and bottom hinge must be greater than the width of the door. 2.3.5.9 Cover Caps: 2.3.5.9.1 D-shaped in polished chrome for door. 2.3.5.9.2 Round in polished chrome for door. 2.3.5.9.3 Round in black for door. 2.3.5.9.4 Nickel plated steel. 2.3.5.9.5 Nickel plated steel with Blum logo (embossed). 2.3.5.9.6 Nickel plated steel with custom logo (minimums apply).
2.3.6 Approved Product: Blum CLIP top 120 Degree Aluminum Door Hinges. 2.3.6.1 Cabinet Construction: 2.3.6.1.1 Frameless for the following application: 2.3.6.1.1.1 Full overlay 2.3.6.2 Hinge Type: 2.3.6.2.1 Straight-arm. 06 41 20-16 2.3.6.3 Angle: 2.3.6.3.1 95 degree: Straight-arm. 2.3.6.4 Suitable for Door Type: 2.3.6.4.1 For aluminum door thickness 18 mm to 22 mm 2.3.6.5 Closing: 2.3.6.5.1 Self-close. 2.3.6.6 Dampening System: Self-regulates the closing speed of the hinge. 2.3.6.6.1 Approved Product: BLUMOTION 973A. 2.3.6.7 Mounting: 2.3.6.7.1 Screw-on. 2.3.6.8 Hinges per Door: 2.3.6.8.1 2 hinges for doors less than 36 inches (914 mm) high and less than 15 lb (7 kg). 2.3.6.8.2 3 hinges for doors less than 64 inches (1626 mm) high and less than 30 lb (14 kg). 2.3.6.8.3 4 hinges for doors less than 86 inches (2184 mm) high and less than 45 lb (20 kg). 2.3.6.8.4 5 hinges for doors less than 96 inches (2438 mm) high and less than 60 lb (27 kg). 2.3.6.8.5 The distance between the top and bottom hinge must be greater than the width of the door. 2.3.6.9 Cover Caps: 2.3.6.9.1 Nylon: Black. 2.3.6.9.2 Nylon: Black with custom logo (minimums apply). 2.3.6.9.3 Nylon: White. 2.3.6.9.4 Nylon: White with custom logo (minimums apply). 2.3.6.9.5 Nickel plated steel. 2.3.6.9.6 Nickel plated steel with Blum logo (embossed). 2.3.6.9.7 Nickel plated steel with custom logo (minimums apply).
2.3.7 Approved Product: Blum CLIP Hinges 2.3.7.1 Cabinet Construction: 2.3.7.1.1 Face frame for the following application: 2.3.7.1.1.1 Full overlay. 06 41 20-17 2.3.7.1.1.2 Partial overlay. 2.3.7.1.1.3 Twin overlay. 2.3.7.1.1.4 Inset 2.3.7.1.2 Frameless for the following application: 2.3.7.1.2.1 Full overlay. 2.3.7.1.2.2 Partial overlay. 2.3.7.1.2.3 Twin overlay. 2.3.7.1.2.4 Inset. 2.3.7.2 Hinge Type: 2.3.7.2.1 Straight-arm. 2.3.7.2.2 Half-cranked. 2.3.7.2.3 Full-cranked. 2.3.7.3 Angle: 2.3.7.3.1 107 degree. 2.3.7.3.2 100 degree. 2.3.7.4 Suitable for Door Type: 2.3.7.4.1 For door thickness 16 mm to 24 mm, material consist of wood, melamine, MDF or particleboard. 2.3.7.5 Closing: 2.3.7.5.1 Self-close. 2.3.7.5.2 Free swing. 2.3.7.6 Dampening System: Self-regulates the closing speed of the hinge 2.3.7.6.1 Approved Product: BLUMOTION 973A. 2.3.7.6.2 Approved Product: BLUMOTION 971A. 2.3.7.6.3 Approved Product: BLUMOTION 970A. 2.3.7.7 Mounting: 2.3.7.7.1 Screw-on. 2.3.7.7.2 Press-in. 2.3.7.7.3 INSERTA, tool-free assembly. 2.3.7.8 Hinges per Door: 2.3.7.8.1 2 hinges for doors less than 36 inches (914 mm) high and less than 15 lb (7 kg). 06 41 20-18 2.3.7.8.2 3 hinges for doors less than 64 inches (1626 mm) high and less than 30 lb (14 kg). 2.3.7.8.3 4 hinges for doors less than 86 inches (2184 mm) high and less than 45 lb (20 kg). 2.3.7.8.4 5 hinges for doors less than 96 inches (2438 mm) high and less than 60 lb (27 kg). 2.3.7.8.5 The distance between the top and bottom hinge must be greater than the width of the door. 2.3.7.9 Cover Caps: 2.3.7.9.1 Nylon: Black. 2.3.7.9.2 Nylon: Black with custom logo (minimums apply). 2.3.7.9.3 Nylon: White. 2.3.7.9.4 Nylon: White with custom logo (minimums apply). 2.3.7.9.5 Nickel plated steel. 2.3.7.9.6 Nickel plated steel with Blum logo (embossed). 2.3.7.9.7 Nickel plated steel with custom logo (minimums apply).
2.3.8 Approved Product: Blum COMPACT Concealed Hinges. 2.3.8.1 Cabinet Construction: 2.3.8.1.1 Face frame for the following application: 2.3.8.1.1.1 1/4 inch (6.35 mm) overlay. 2.3.8.1.1.2 3/8 inch (9.5 mm) overlay. 2.3.8.1.1.3 1/2 inch (12.7 mm) overlay. 2.3.8.1.1.4 5/8 inch (15.9) overlay. 2.3.8.1.1.5 3/4 inch (19 mm) overlay. 2.3.8.1.1.6 1 inch (25.4 mm) overlay. 2.3.8.1.1.7 1-1/8 inches (27.6 mm) overlay. 2.3.8.1.1.8 1-1/4 inches (31.8 mm) overlay. 2.3.8.1.1.9 1-5/16 inches (33 mm) overlay. 2.3.8.1.1.10 1-3/8 inches (35 mm) overlay. 2.3.8.1.1.11 1-1/2 inches (38 mm) overlay. 2.3.8.1.1.12 1-9/16 inches (39.7 mm) overlay. 2.3.8.1.1.13 1-5/8 inches (41.2 mm) overlay. 2.3.8.1.1.14 06 41 20-19 1-3/8 inches (41.2 mm) plus overlay face mount. 2.3.8.2 Hinge Type: 2.3.8.2.1 One piece. 2.3.8.2.2 Two piece. 2.3.8.2.3 Wraparound. 2.3.8.2.4 Edge mount. 2.3.8.2.5 Face mount. 2.3.8.3 Angle: 2.3.8.3.1 105 degree. 2.3.8.3.2 107 degree. 2.3.8.3.3 110 degree. 2.3.8.4 Suitable for Door Type: 2.3.8.4.1 For door thickness 16 mm to 19 mm, material consist of wood, melamine, MDF or particleboard. 2.3.8.5 Closing: 2.3.8.5.1 Self-close. 2.3.8.6 Dampening System: Self-regulates the closing speed of the hinge 2.3.8.6.1 Approved Product: BLUMOTION 971A. 2.3.8.7 Mounting: 2.3.8.7.1 Screw-on. 2.3.8.7.2 Press-in. 2.3.8.8 Hinges per Door: 2.3.8.8.1 2 hinges for doors less than 36 inches (914 mm) high and less than 15 lb (7 kg). 2.3.8.8.2 3 hinges for doors less than 64 inches (1626 mm) high and less than 30 lb (14 kg). 2.3.8.8.3 4 hinges for doors less than 86 inches (2184 mm) high and less than 45 lb (20 kg). 2.3.8.8.4 5 hinges for doors less than 96 inches (2438 mm) high and less than 60 lb (27 kg). 2.3.8.8.5 The distance between the top and bottom hinge must be greater than the width of the door. 2.3.8.9 Cover Caps: 2.3.8.9.1 Nickel plated steel. 2.3.8.9.2 06 41 20-20 Nickel plated steel with Blum logo (embossed). 2.3.8.9.3 Nickel plated steel with custom logo (minimums apply).
2.3.9 Approved Product: Blum COMPACT BLUMOTION Concealed Hinges. 2.3.9.1 Cabinet Construction: 2.3.9.1.1 Face frame for the following application: 2.3.9.1.1.1 5/16 inch (7.9 mm) overlay. 2.3.9.1.1.2 3/8 inch (9.5 mm) overlay. 2.3.9.1.1.3 1/2 inch (12.7 mm) overlay. 2.3.9.1.1.4 5/8 inch (15.9) overlay. 2.3.9.1.1.5 3/4 inch (19 mm) overlay. 2.3.9.1.1.6 1 inch (25.4 mm) overlay. 2.3.9.1.1.7 1-1/4 inches (31.8 mm) overlay. 2.3.9.1.1.8 1-5/16 inches (33 mm) overlay. 2.3.9.1.1.9 1-3/8 inches (35 mm) overlay. 2.3.9.1.1.10 1-1/2 inches (38 mm) overlay. 2.3.9.1.1.11 1-9/16 inches (39.7 mm) overlay. 2.3.9.1.1.12 1-3/8 inches (41.2 mm) plus overlay face mount. 2.3.9.2 Hinge Type: 2.3.9.2.1 One piece. 2.3.9.2.2 Wraparound. 2.3.9.2.3 Edge mount. 2.3.9.2.4 Face mount. 2.3.9.3 Angle: 2.3.9.3.1 105 degree. 2.3.9.3.2 107 degree. 2.3.9.3.3 110 degree. 2.3.9.4 Suitable for Door Type: 2.3.9.4.1 For door thickness 16 mm to 19 mm, material consist of wood, melamine, MDF or particleboard. 2.3.9.5 Closing: 2.3.9.5.1 Soft close. 2.3.9.6 06 41 20-21 Dampening System: Self-regulates the closing speed of the hinge 2.3.9.6.1 Integrated into hinge. 2.3.9.7 Mounting: 2.3.9.7.1 Screw-on. 2.3.9.7.2 Press-in. 2.3.9.8 Hinges per Door: 2.3.9.8.1 2 hinges for doors less than 36 inches (914 mm) high and less than 15 lb (7 kg). 2.3.9.8.2 3 hinges for doors less than 64 inches (1626 mm) high and less than 30 lb (14 kg). 2.3.9.8.3 4 hinges for doors less than 86 inches (2184 mm) high and less than 45 lb (20 kg). 2.3.9.8.4 5 hinges for doors less than 96 inches (2438 mm) high and less than 60 lb (27 kg). 2.3.9.8.5 The distance between the top and bottom hinge must be greater than the width of the door. 2.3.9.9 Cover Caps: 2.3.9.9.1 Nickel plated steel. 2.3.9.9.2 Nickel plated steel with Blum logo (embossed). 2.3.9.9.3 Nickel plated steel with custom logo (minimums apply).
2.4 DRAWER RUNNER SYSTEMS
2.4.1 Approved Product: Blum TANDEM Concealed Runners for Wood Drawers. 2.4.1.1 Cabinet Construction: 2.4.1.1.1 Face frame for the following application: 2.4.1.1.1.1 Full overlay. 2.4.1.1.1.2 Inset. 2.4.1.1.1.3 Narrow. 2.4.1.1.1.4 Interior roll-out/shelf/tray. 2.4.1.1.1.5 Bottom mount. 2.4.1.1.1.6 SPACE CORNER - 90 degree corner cabinet with drawers. 2.4.1.1.1.7 Deep. 2.4.1.1.2 Frameless for the following application: 2.4.1.1.2.1 Full overlay. 06 41 20-22 2.4.1.1.2.2 Inset. 2.4.1.1.2.3 Narrow. 2.4.1.1.2.4 Interior roll-out/shelf/tray. 2.4.1.1.2.5 Bottom mount. 2.4.1.1.2.6 SPACE CORNER - 90 degree corner cabinet with drawers. 2.4.1.1.2.7 Deep. 2.4.1.2 Runner Type: 2.4.1.2.1 Full extension. 2.4.1.2.2 Full extension with BLUMOTION. 2.4.1.2.3 Heavy duty full extension with BLUMOTION. 2.4.1.2.4 Bottom mount heavy duty with BLUMOTION. 2.4.1.3 Drawer Length: 2.4.1.3.1 9 inches (229 mm). 2.4.1.3.2 12 inches (305 mm). 2.4.1.3.3 15 inches (381 mm). 2.4.1.3.4 18 inches (457 mm). 2.4.1.3.5 21 inches (533 mm). 2.4.1.3.6 24 inches (610 mm). 2.4.1.3.7 27 inches (686 mm). 2.4.1.3.8 30 inches (762 mm). 2.4.1.4 Drawer Side Thickness: 2.4.1.4.1 Up to 5/8 inch (16 mm). 2.4.1.4.2 Up to 3/4 inch (19 mm). 2.4.1.5 Drawer Weight Capacity: 2.4.1.5.1 75 pounds dynamic/100 pounds static. 2.4.1.5.2 90 pounds dynamic/100 pounds static. 2.4.1.5.3 135 pounds dynamic/150 pounds static. 2.4.1.6 Locking Device: One right and one left required per drawer. 2.4.1.6.1 With side-to-side adjustment: 2.4.1.6.1.1 Standard. 2.4.1.6.1.2 Vertical mount. 06 41 20-23 2.4.1.6.1.3 Depth adjustable. 2.4.1.6.2 Without side-to-side adjustment: 2.4.1.6.2.1 Standard. 2.4.1.6.2.2 Vertical mount. 2.4.1.6.2.3 Narrow drawer. 2.4.1.7 Materials/Finish: 2.4.1.7.1 Runners: Zinc-coated steel with nylon rollers 2.4.1.7.2 Rear brackets/sockets: Zinc-coated steel or nylon 2.4.1.7.3 Locking devices: Stamped steel, zinc die-cast or nylon 2.4.1.7.4 End caps: Nylon 2.4.1.7.5 Bottom/Back/Side spacers: Nylon 2.4.1.8 Closing: 2.4.1.8.1 Self-close. 2.4.1.9 Dampening System: Self-regulates the closing speed of the drawer. 2.4.1.9.1 Integrated into 563 & 569 drawer runners. 2.4.1.10 Mounting: 2.4.1.10.1 Screw-on: side mount or block out. 2.4.1.10.2 Screw-on: frame mount with rear bracket. 2.4.1.10.3 Screw-on: bottom mount. 2.4.1.11 Accessories: 2.4.1.11.1 ORGA-LINE: 2.4.1.11.1.1 Flatware set: Part No. ______2.4.1.11.1.2 Flatware tray: Part No. ______2.4.1.11.1.3 Utensil set: Part No. ______2.4.1.11.1.4 4.) Plate holder: Part No. ______2.4.1.11.1.5 Spice trays: Part No. 2.4.1.11.1.6 Knife holder: Part No. ______2.4.1.11.1.7 Deep drawer cross divider: Part No. ______2.4.1.11.2 SERVO-DRIVE: Electric opening of the drawer with just a light touch of the front. 2.4.1.11.3 TIP-ON: Mechanical opening of the drawer with just a light touch of the front.
06 41 20-24 2.4.2 Approved Product: Blum STANDARD Drawer Runners for Wood Drawers. 2.4.2.1 Cabinet Construction: 2.4.2.1.1 Face frame for the following application: 2.4.2.1.1.1 Full overlay. 2.4.2.1.1.2 Bottom mount. 2.4.2.1.1.3 Deep. 2.4.2.1.2 Frameless for the following application: 2.4.2.1.2.1 Full overlay. 2.4.2.1.2.2 Bottom mount. 2.4.2.1.2.3 Deep. 2.4.2.2 Runner Type: 2.4.2.2.1 Partial extension. 2.4.2.2.2 Full extension. 2.4.2.3 Drawer Length: 2.4.2.3.1 10 inches (250 mm). 2.4.2.3.2 12 inches (300 mm). 2.4.2.3.3 14 inches (350 mm). 2.4.2.3.4 16 inches (400 mm). 2.4.2.3.5 18 inches (450 mm). 2.4.2.3.6 20 inches (500 mm). 2.4.2.3.7 22 inches (550 mm). 2.4.2.3.8 24 inches (600 mm). 2.4.2.3.9 26 inches (650 mm). 2.4.2.3.10 28 inches (700 mm). 2.4.2.3.11 30 inches (753 mm). 2.4.2.3.12 32 inches (803 mm). 2.4.2.4 Drawer Weight Capacity: 2.4.2.4.1 75 pounds dynamic/100 pounds static. 2.4.2.5 Materials/Finish: 2.4.2.5.1 Cream epoxy coated steel. 2.4.2.6 Closing: 06 41 20-25 2.4.2.6.1 Self-close. 2.4.2.7 Mounting: 2.4.2.7.1 Screw-on: side mount or block out. 2.4.2.7.2 Screw-on: frame mount with rear bracket. 2.4.2.7.3 Screw-on: bottom mount.
2.5 BOX SYSTEMS
2.5.1 Approved Product: Blum LEGRABOX Premium Metal Drawer System 2.5.1.1 Cabinet Construction: 2.5.1.1.1 Frameless for the following application: 2.5.1.1.1.1 Standard drawer. 2.5.1.1.1.2 Pantry. 2.5.1.1.1.3 Sink. 2.5.1.1.1.4 Deep drawer. 2.5.1.2 Runner Type: 2.5.1.2.1 Full extension with BLUMOTION. 2.5.1.2.2 Heavy duty full extension with BLUMOTION. 2.5.1.3 Drawer Length: 2.5.1.3.1 11 inches (270 mm). 2.5.1.3.2 14 inches (350 mm). 2.5.1.3.3 16 inches (400 mm). 2.5.1.3.4 18 inches (450 mm). 2.5.1.3.5 20 inches (500 mm). 2.5.1.3.6 22 inches (550 mm). 2.5.1.3.7 24 inches (600 mm). 2.5.1.4 Drawer Height: 2.5.1.4.1 LEGRABOX M: 3-9/16 inches (90.5 mm). 2.5.1.4.2 LEGRABOX C: 7 inches (177 mm). 2.5.1.4.3 LEGRABOX F: 9-1/2 inches (241 mm). 2.5.1.5 Drawer Side Thickness: 2.5.1.5.1 1/2 inch (12.8 mm). 06 41 20-26 2.5.1.6 Drawer Weight Capacity: 2.5.1.6.1 88 pounds dynamic/100 pounds static. 2.5.1.6.2 155 pounds dynamic/175 pounds static. 2.5.1.7 Materials/Finish: 2.5.1.7.1 Orion gray. 2.5.1.7.2 Brushed stainless steel. 2.5.1.8 Closing: 2.5.1.8.1 Self-close. 2.5.1.9 Dampening System: Self-regulates the closing speed of the drawer 2.5.1.9.1 Integrated. 2.5.1.10 Accessories: 2.5.1.10.1 AMBIA-LINE 2.5.1.10.1.1 Flatware set: Part No. ______2.5.1.10.1.2 Utensil set: Part No. 2.5.1.10.1.3 Plate holder: Part No. ______2.5.1.10.1.4 Spice trays: Part No. ______2.5.1.10.1.5 Knife holder: Part No. ______2.5.1.10.1.6 Deep drawer frame: Part No. ______2.5.1.10.1.7 Deep drawer adapter plate: Part No. ______2.5.1.10.2 SERVO-DRIVE: Electric opening of the drawer with just a light touch of the front. 2.5.1.10.3 TIP-ON: Mechanical opening of the drawer with just a light touch of the front 2.5.1.10.4 Cover Caps - outside: 2.5.1.10.4.1 Orion gray. 2.5.1.10.4.2 Nickel. 2.5.1.10.5 Cover Caps - inside: 2.5.1.10.5.1 Orion gray. 2.5.1.10.5.2 Nickel. 2.5.1.10.6 Lateral stabilizer set.
2.5.2 Approved Product: Blum TANDEMBOX Deluxe Metal Drawer System 2.5.2.1 Cabinet Construction: 06 41 20-27 2.5.2.1.1 Frameless for the following application: 2.5.2.1.1.1 Standard drawer. 2.5.2.1.1.2 Pantry. 2.5.2.1.1.3 File. 2.5.2.1.2 Waste/recycle. 2.5.2.1.3 Sink. 2.5.2.1.4 SPACE CORNER - 90 degree corner cabinet with drawers 7.) Deep drawer. 2.5.2.2 Runner Type: 2.5.2.2.1 Full extension with BLUMOTION. 2.5.2.2.2 Heavy duty full extension with BLUMOTION. 2.5.2.2.3 Bottom mount heavy duty with BLUMOTION. 2.5.2.3 Drawer Length: 2.5.2.3.1 11 inches (270 mm). 2.5.2.3.2 14 inches (350 mm). 2.5.2.3.3 16 inches (400 mm). 2.5.2.3.4 18 inches (450 mm). 2.5.2.3.5 20 inches (500 mm). 2.5.2.3.6 22 inches (550 mm). 2.5.2.3.7 24 inches (600 mm). 2.5.2.3.8 26 inches (650 mm). 2.5.2.4 Drawer Height: 2.5.2.4.1 TANDEMBOX N: 2-11/16 inches (69 mm). 2.5.2.4.2 TANDEMBOX M: 3-5/16 inches (84 mm). 2.5.2.4.3 TANDEMBOX B: 5-3/4 inches (146 mm). 2.5.2.4.4 TANDEMBOX D: 8-1/8 inches (207 mm). 2.5.2.5 Drawer Side Thickness: 2.5.2.5.1 19/32 inch (15 mm). 2.5.2.6 Drawer Weight Capacity: 2.5.2.6.1 75 pounds dynamic/100 pounds static. 2.5.2.6.2 150 pounds dynamic/175 pounds static. 2.5.2.7 Materials/Finish: 06 41 20-28 2.5.2.7.1 Gray. 2.5.2.7.2 Stainless steel. 2.5.2.7.3 Silk white (waste/recycle set only). 2.5.2.8 Closing: 2.5.2.8.1 Self-close. 2.5.2.9 Dampening System: Self-regulates the closing speed of the drawer 2.5.2.9.1 Integrated. 2.5.2.10 Accessories: 2.5.2.10.1 ORGA-LINE: 2.5.2.10.1.1 Flatware set: Part No. ______2.5.2.10.1.2 Flatware tray: Part No. ______2.5.2.10.1.3 Utensil set: Part No. ______2.5.2.10.1.4 Plate holder: Part No. ______2.5.2.10.1.5 Spice trays: Part No. ______2.5.2.10.1.6 Knife holder: Part No. ______2.5.2.10.1.7 Deep drawer cross divider: Part No. ______2.5.2.10.1.8 Deep drawer cross gallery rail: Part No. ______2.5.2.10.2 SERVO-DRIVE: Electric opening of the drawer with just a light touch of the front 2.5.2.10.3 TIP-ON: Mechanical opening of the drawer with just a light touch of the front
2.5.3 Approved Product: Blum METABOX Versatile Metal Drawer System 2.5.3.1 Cabinet Construction: 2.5.3.1.1 Face frame for the following application: 2.5.3.1.1.1 Standard drawer. 2.5.3.1.1.2 Pantry. 2.5.3.1.1.3 File. 2.5.3.1.1.4 Deep drawer. 2.5.3.1.2 Frameless for the following application: 2.5.3.1.2.1 Standard drawer. 2.5.3.1.2.2 Pantry. 2.5.3.1.2.3 File. 06 41 20-29 2.5.3.1.2.4 Deep drawer. 2.5.3.2 Runner Type: 2.5.3.2.1 320 Series: 3/4 extension. 2.5.3.2.2 320 Series: 3/4 extension with BLUMOTION (add-on). 2.5.3.2.3 330 Series: Full extension with 3/4 inch (18 mm) over extension. 2.5.3.3 Drawer Length: 2.5.3.3.1 11 inches (270 mm). 2.5.3.3.2 14 inches (350 mm). 2.5.3.3.3 16 inches (400 mm). 2.5.3.3.4 18 inches (450 mm). 2.5.3.3.5 20 inches (500 mm). 2.5.3.3.6 22 inches (550 mm). 2.5.3.4 Drawer Height: 2.5.3.4.1 METABOX N: 2-1/8 inches (54 mm). 2.5.3.4.2 METABOX M: 3-3/8 inches (86 mm). 2.5.3.4.3 METABOX K: 4-5/8 inches (118 mm). 2.5.3.4.4 METABOX H: 5-7/8 inches (150 mm). 2.5.3.5 Drawer Side Thickness: 2.5.3.5.1 1/16 inch (1.5 mm). 2.5.3.6 Drawer Weight Capacity: 2.5.3.6.1 75 pounds dynamic/100 pounds static. 2.5.3.7 Materials/Finish: 2.5.3.7.1 White epoxy coated. 2.5.3.8 Closing: 2.5.3.8.1 Self-close. 2.5.3.9 Dampening System: Self-regulates the closing speed of the drawer 2.5.3.9.1 320 Series: BLUMOTION add-on Z70.0320. 2.5.3.10 Accessories: 2.5.3.10.1 Organization: 2.5.3.10.1.1 INSERTA (tool free) gallery set: Part No. ______2.5.3.10.1.2 BOXSIDE (2 required): Part No. ______06 41 20-30 2.5.3.10.1.3 Cross gallery rail: Part No. ______2.5.3.10.1.4 Cross gallery connectors (2 required): Part No. ______2.5.3.10.2 File drawer set: Part No. ______2.5.3.10.3 Cover Caps: 2.5.3.10.3.1 Nylon: White. 2.5.3.10.4 SERVO-DRIVE: Electric opening of the drawer with just a light touch of the front 2.5.3.10.5 TIP-ON: Mechanical opening of the drawer with just a light touch of the front.
2.6 ELECTRONIC OPENING SYSTEMS
2.6.1 Approved Product: Blum vertical aluminum profile for TANDEM. 2.6.1.1 Vertical Aluminum Profile: 2.6.1.1.1 Part number: Z10T720AB - Profile with cable, length 28-3/8 inches (720 mm). 2.6.1.1.2 Part number: Z10T1170A - Profile without cable, length 46 inches (1170 mm). 2.6.1.2 Top And Bottom Adapter Set: 2.6.1.2.1 Part number: Z10D01E0.01 - For use with horizontal stretcher rail. 2.6.1.3 Back And Bottom Adapter Set: 2.6.1.3.1 Part number: Z10D01EA.01 - For use with back stretcher rail. 2.6.1.4 Drive Unit: 2.6.1.4.1 Part number: Z10A3000.02. 2.6.1.5 Distance Bumper: 2.6.1.5.1 Part number: 933.0531 - 5 mm diameter bumper. 2.6.1.5.2 Part number: 933.1220 - Screw-on bumper. 2.6.1.6 Power Supply Set: 2.6.1.6.1 Part number: Z10NE02UG10.
2.6.2 Approved Product: Blum inset vertical aluminum profile for TANDEM. 2.6.2.1 Inset Vertical Aluminum Profile: 2.6.2.1.1 Part number: Z10T720AB - Profile with cable, length 28-3/8 inches (720 mm). 2.6.2.1.2 Part number: Z10T1170A - Profile without cable, length 46 inches (1170 mm). 2.6.2.2 Top And Bottom Adapter Set: 2.6.2.2.1 Part number: Z10D01E0.01 - For use with horizontal stretcher rail. 06 41 20-31 2.6.2.3 Drive Unit: 2.6.2.3.1 Part number: Z10A3000.02. 2.6.2.4 Locking Device With Integrated Distance Bumper (Both Required): 2.6.2.4.1 Part number: T51.1901.PS L. 2.6.2.4.2 Part number: T51.1901.PS R. 2.6.2.5 Power Supply Set: 2.6.2.5.1 Part number: Z10NE02UG10.
2.6.3 Approved Product: Blum horizontal aluminum profile for TANDEM. 2.6.3.1 Horizontal Aluminum Profile: 2.6.3.1.1 Part number: Z10T1143B - Profile length 45 inches (1143 mm). 2.6.3.2 Adapter Set: 2.6.3.2.1 Part number: Z10D5800.US. 2.6.3.3 Drive Unit: 2.6.3.3.1 Part number: Z10A3000.02. 2.6.3.4 Distance Bumper: 2.6.3.4.1 Part number: 933.0531 - 5 mm diameter bumper. 2.6.3.4.2 Part number: 933.1220 - Screw-on bumper. 2.6.3.5 Power Supply Set: 2.6.3.5.1 Part number: Z10NE02UG10.
2.6.4 Approved Product: Blum inset horizontal aluminum profile for TANDEM. 2.6.4.1 Inset Horizontal Aluminum Profile: 2.6.4.1.1 Part number: Z10T1143B - Profile length 45 inches (1143 mm). 2.6.4.2 Adapter Set: 2.6.4.2.1 Part number: Z10D5800.US. 2.6.4.3 Drive Unit: 2.6.4.3.1 Part number: Z10A3000.02. 2.6.4.4 Locking Device With Integrated Distance Bumper (Both Required): 2.6.4.4.1 Part number: T51.1901.PS L. 2.6.4.4.2 Part number: T51.1901.PS R. 2.6.4.5 Power Supply Set: 06 41 20-32 2.6.4.5.1 Part number: Z10NE02UG10.
2.6.5 Approved Product: Blum top bracket for TANDEM. 2.6.5.1 Top Bracket With Adapter: 2.6.5.1.1 Part number: Z10D6252. 2.6.5.2 Drive Unit: 2.6.5.2.1 Part number: Z10A3000.02. 2.6.5.3 Distance Bumper: 2.6.5.3.1 Part number: 933.0531 - 5 mm diameter bumper. 2.6.5.3.2 Part number: 933.1220 - Screw-on bumper. 2.6.5.4 Power Supply Set: 2.6.5.4.1 Part number: Z10NE02UG10.
2.6.6 Approved Product: Blum inset top bracket for TANDEM. 2.6.6.1 Top Bracket With Adapter: 2.6.6.1.1 Part number: Z10D6252. 2.6.6.2 Drive Unit: 2.6.6.2.1 Part number: Z10A3000.02. 2.6.6.3 Locking Device With Integrated Distance Bumper (Both Required): 2.6.6.3.1 Part number: T51.1901.PS L. 2.6.6.3.2 Part number: T51.1901.PS R. 2.6.6.4 Power Supply Set: 2.6.6.4.1 Part number: Z10NE02UG10.
2.6.7 Approved Product: Blum bottom bracket for TANDEM. 2.6.7.1 Bottom Bracket: 2.6.7.1.1 Part number: Z10D7201.01. 2.6.7.2 Drive Unit: 2.6.7.2.1 Part number: Z10A3000.02. 2.6.7.3 Distance Bumper: 2.6.7.3.1 Part number: 933.0531 - 5 mm diameter bumper. 2.6.7.3.2 Part number: 933.1220 - Screw-on bumper. 2.6.7.4 06 41 20-33 Power Supply Set: 2.6.7.4.1 Part number: Z10NE02UG10.
2.6.8 Approved Product: Blum inset bottom bracket for TANDEM 2.6.8.1 Bottom Bracket: 2.6.8.1.1 Part number: Z10D7201.01. 2.6.8.2 Drive Unit: 2.6.8.2.1 Part number: Z10A3000.02. 2.6.8.3 Locking Device With Integrated Distance Bumper (Both Required): 2.6.8.3.1 Part number: T51.1901.PS L. 2.6.8.3.2 Part number: T51.1901.PS R. 2.6.8.4 Power Supply Set: 2.6.8.4.1 Part number: Z10NE02UG10
2.6.9 Approved Product: Blum Waste/recycle set. 2.6.9.1 Part number: Z10NA20UGUS.
2.6.10 Approved Product: Blum vertical aluminum profile for TANDEMBOX 2.6.10.1 Vertical Aluminum Profile: 2.6.10.1.1 Part number: Z10T720AB - Profile with cable, length 28-3/8 inches (720 mm). 2.6.10.1.2 Part number: Z10T1170A - Profile without cable, length 46 inches (1170 mm) 2.6.10.2 Top And Bottom Adapter Set:. 2.6.10.2.1 Part number: Z10D01E0.01 - For use with horizontal stretcher rail. 2.6.10.3 Back And Bottom Adapter Set: 2.6.10.3.1 Part number: Z10D01EA.01 - For use with back stretcher rail. 2.6.10.4 Drive Unit: 2.6.10.4.1 Part number: Z10A3000.02. 2.6.10.5 Distance Bumper: 2.6.10.5.1 Part number: 933.0531 - 5 mm diameter bumper. 2.6.10.5.2 Part number: 933.1220 - Screw-on bumper. 2.6.10.6 Power Supply Set: 2.6.10.6.1 Part number: Z10NE02UG10.
2.6.11 06 41 20-34 Approved Product: Blum horizontal aluminum profile for TANDEMBOX. 2.6.11.1 Horizontal Aluminum Profile: 2.6.11.1.1 Part number: Z10T1143B - Profile length 45 inches (1143 mm). 2.6.11.2 Adapter Set: 2.6.11.2.1 Part number: Z10D5210.US. 2.6.11.3 Drive Unit: 2.6.11.3.1 Part number: Z10A3000.02. 2.6.11.4 Distance Bumper: 2.6.11.4.1 Part number: 933.0531 - 5 mm diameter bumper. 2.6.11.4.2 Part number: 933.1220 - Screw-on bumper. 2.6.11.5 Power Supply Set: 2.6.11.5.1 Part number: Z10NE02UG10.
2.6.12 Approved Product: Blum top bracket for TANDEMBOX. 2.6.12.1 Top Bracket With Adapter: 2.6.12.1.1 Part number: Z10D6252. 2.6.12.2 Drive Unit: 2.6.12.2.1 Part number: Z10A3000.02. 2.6.12.3 Distance Bumper: 2.6.12.3.1 Part number: 933.0531 - 5 mm diameter bumper. 2.6.12.3.2 Part number: 933.1220 - Screw-on bumper. 2.6.12.4 Power Supply Set: 2.6.12.4.1 Part number: Z10NE02UG10.
2.6.13 Approved Product: Blum bottom bracket for TANDEMBOX. 2.6.13.1 Bottom Bracket: 2.6.13.1.1 Part number: Z10D7201.01. 2.6.13.2 Drive Unit: 2.6.13.2.1 Part number: Z10A3000.02. 2.6.13.3 Distance Bumper: 2.6.13.3.1 Part number: 933.0531 - 5 mm diameter bumper. 2.6.13.3.2 Part number: 933.1220 - Screw-on bumper. 2.6.13.4 06 41 20-35 Power Supply Set: 2.6.13.4.1 Part number: Z10NE02UG10.
3 EXECUTION
3.1 EXAMINATION
3.1.1 Do not begin installation until substrates have been properly prepared.
3.1.2 If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
3.2 PREPARATION
3.2.1 Clean surfaces thoroughly prior to installation.
3.2.2 Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
3.3 INSTALLATION
3.3.1 Install in accordance with manufacturer's instructions.
3.4 PROTECTION
3.4.1 Protect installed products until completion of project.
3.4.2 Touch-up, repair or replace damaged products before Substantial Completion.
END OF SECTION
06 41 20-36