DOCSLIB.ORG

3-Color Display Rohs Electromagnetic Digital Flow Switch Applicable Fluid Water, Water-Soluble Coolant

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
3-Color Display Rohs Electromagnetic Digital Flow Switch Applicable Fluid Water, Water-Soluble Coolant 3-Color Display RoHS Electromagnetic Digital Flow Switch Applicable fluid Water, Water-soluble coolant Actual size Compact Lightweight The oval fluid 56 mm passage enables the width to be 340 g reduced. (LFE1m3) 40 mm New An insulated type has been added. Positive ground Negative ground 2 types of ground are available. A close proximity setting is available. ¡ Fluctuation of the displayed value can be reduced when the close proximity setting function is used. ¡ Reduced setting time ∗ Not available for the remote type Variations Flow range Integrated display type/Remote type 0.5 L/min 2 L/min 5 L/min 10 L/min 20 L/min 50 L/min 100 L/min 200 L/min LFE1 Rated flow range Display flow range LFE1mZ LFE2 Rated flow range Display flow range LFE2mZ LFE3 Display flow range Rated flow range LFE3mZ LFEm Series CAT.ES100-107D 3-Color Display Electromagnetic Digital Flow Switch LFEm Series New An insulated type has been added. The ground doesn’t need Marking (Blue) to be selected when wiring. Insulated type/LFEmZ Non-insulated type/LFEm The piping port is insulated The piping port is connected to the with the power supply. negative ground of the power supply. PositivePositive ground ground PositivePositive ground ground 2424 V V 2424 V V PipingPiping port port PipingPiping PipingPiping port port PipingPiping InsulationInsulation GroundGround (0 (0V) V) GroundGround (0 (0V) V) ElectricElectric potential potential GroundGround (0 (0V) V) differencedifference GroundGround (−24 (−24 V) V) ShortShort NegativeNegative ground ground NegativeNegative ground ground 2424 V V 2424 V V InsulationInsulation GroundGround (0 (0V) V) GroundGround (0 (0V) V) GroundGround (0 (0V) V) GroundGround (0 (0V) V) Pressure loss: 0.02 MPa or less Reverse flow can be detected. Pressure loss [MPa] Reverse flow error display 0.05 Reverse flow error (Code LLL) 0.04 0.03 0.02 Reverse flow 0.01 0 50 100 Flow rate [L/min] Repeatability: ±1.5% F.S. A zero-reset setting is available. (Analog output) The display can be adjusted to zero. Operating fluid temperature: 0 to 85°C Made to Order p. 19 Piping connection ports: Stainless steel 304 ∗ Integrated display type only 1 3-Color Display Electromagnetic Digital Flow Switch LFEm Series Flow direction can be 3-color/2-screen changed after installation. display ¡Default flow direction OUT (Forward direction) Instantaneous flow rate is displayed. IN Customer’s flow direction ¡Flow direction can be changed after installation. The parameters below can be set. ¡Set value ¡Flow direction ¡Accumulated value ¡Line name ¡Peak/Bottom value Forward direction Reverse direction (Left to right) (Right to left) IN OUT Application Examples Flow control for Flow control for water-soluble coolant Flow control for cooling water for pressurized cooling metal molds water for welding guns Principle Faraday’s law of induction Fluid velocity (V) Measure the volume flow of inductive liquids by applying Coil Faraday’s law of induction: “when a conductive object is Fluid passage/ moved through a magnetic field, an electromotive force will Piping be generated.” Fluid Electrode The electromotive force (E) is proportional to the fluid velocity (V) multiplied by the magnetic flux density (B). The volume flow is calculated by converting the measured Electromotive force (E) electromotive force (E). An oval fluid passage is used to improve themagnetic flux density (B) generated by small amounts of current. Magnetic flux density (B) 2 Flow Switch for Fluid Variations Applicable Detection Smallest Rated flow range [L/min] Series settable Enclosure∗1 Display fluid method increment 0 0.5 2 5 10 20 30 40 50 100 150 200 250 LFE 0.1 L/min 0.5 20 Water, 3-color Water-soluble Electromagnetic 0.5 L/min IP65 2.5 100 display coolant 1 L/min 5 200 PF3W-Z 0.01 L/min 0.5 4 Water, 0.1 L/min 2 16 Ethylene Karman 3-color glycol IP65 vortex display aqueous solution 0.1 L/min 5 40 1 L/min 10 100 PF3W-L-Z 0.01 L/min 0.5 4 Water, 0.1 L/min 2 16 Ethylene Karman 3-color glycol IP65 vortex display aqueous solution 0.1 L/min 5 40 1 L/min 10 100 PF3W721-L Water, Karman 3-color Ethylene glycol 2 L/min IP65 50 250 aqueous solution vortex display PF3W 0.01 L/min 0.5 4 0.1 L/min 2 16 Water, Ethylene Karman 3-color glycol 0.1 L/min IP65 5 40 vortex display aqueous solution 1 L/min 10 100 2 L/min 50 250 PVC piping type Water, 1 L/min 10 100 Ethylene Karman 3-color glycol IP65 vortex display aqueous solution 2 L/min 30 250 PF2D 0.05 L/min 0.4 4 Deionized water (pure water), Karman 1-color Liquids which 0.1 L/min IP65 1.8 20 vortex display do not corrode nor erode fluoropolymer 0.5 L/min 4 40 ∗1 For the remote type monitor unit, only the front side is IP65 compliant. The other parts are IP40 compliant. 3 CONTENTS 3-Color Display Electromagnetic Digital Flow Switch LFE Series 3-Color Display Digital Flow Monitor LFE0 Series 3-Color Display Electromagnetic Digital Flow Switch LFE Series How to Order ·································································································································· p. 5 Specifications (Integrated Display Type) ········································································ p. 6 Specifications (Remote Type) ······························································································· p. 7 Flow Rate Characteristics (Pressure Loss) ································································ p. 8 Internal Circuits and Wiring Examples ··········································································· p. 9 Parts Description ······················································································································ p. 10 Fluid Passage Structure ······································································································· p. 10 Dimensions ··································································································································· p. 11 3-Color Display Digital Flow Monitor LFE0 Series How to Order ······························································································································· p. 12 Specifications (Remote Type Monitor) ········································································ p. 13 Internal Circuits and Wiring Examples ········································································ p. 14 Parts Description (Remote Type Monitor) ································································· p. 15 Dimensions ··································································································································· p. 16 Function Details ······························································································································· p. 17 Made to Order ··································································································································· p. 19 Specific Product Precautions ·································································································· p. 20 Safety Instructions ············································································································ Back cover 4 3-Color Display Electromagnetic Digital Flow Switch RoHS LFE Series Integrated display type How to Order Non-insulated type Insulated type Insulated type LFE 1 A 3 Z The piping port is insulated with the power supply. Remote type monitor Non-insulated type 1 A 3 Remote type For details, refer LFE to page 12. The piping port is connected to the negative ground of the power supply. Rated flow range Symbol Rated flow range Made to order (Refer to page 19.) 1 0.5 to 20 L/min Symbol Description 2 2.5 to 100 L/min X8 Piping connection ports: Stainless steel 304 3 5 to 200 L/min Output specifications Option Insulated Non-insulated Lead wire and M12 Symbol OUT1 OUT2 Symbol Bracket Display unit type type connector (Length 3 m) A NPN NPN VV Nil V — L/min B PNP PNP VV 1 — — L/min Integrated C NPN Analog 1 to 5 V VV V V L/min display 2 NPN Analog 4 to 20 mA VV type D 3 — V L/min E PNP Analog 1 to 5 V V — 4∗1∗2 V — gal/min F PNP Analog 4 to 20 mA V — 5∗1∗2 — — gal/min Remote J∗1 — Analog 1 to 5 V VV 6∗1∗2 V V gal/min type K∗2 — Analog 4 to 20 mA VV 7∗1∗2 — V gal/min ∗1 J: Select when used in combination with a digital flow monitor. ∗1 Options 4, 5, 6, and 7, which are not in SI units, are not for ∗2 K: Cannot be used in combination with a digital flow monitor use in Japan due to the New Measurement Act. ∗2 Options 4, 5, 6, and 7 cannot be selected when the output specification is J or K. Port size Reference: 1 [L/min] = 0.2642 [gal/min] Applicable model 1 [gal/min] = 3.785 [L/min] Symbol Port size LFE1 LFE2 LFE3 3 3/8 V —— 4 1/2 V —— 6 3/4 — V — 8 1 — — V Thread type Symbol Type The close proximity setting and zero-reset functions are only Nil Rc available for the integrated display type. For the remote type, the close proximity setting and zero-reset N NPT functions cannot be used. F G Options/Part Nos. When only optional parts are required, order with the part numbers listed below. Option Part no. Note Weight Lead wire and M12 connector LFE-1-A3 Lead wire length 3 m Approx. 175 g Option Part no. Note Weight LFE-1-D Tapping screw for LFE1 (3 x 10), 4 pcs. Approx. 45 g Bracket LFE-2-D Tapping screw for LFE2 (3 x 10), 4 pcs. Approx. 70 g LFE-3-D Tapping screw for LFE3 (3 x 10), 4 pcs. Approx. 70 g 5 3-Color Display Electromagnetic Digital Flow Switch LFE Series For flow switch precautions, refer to the Operation Manual on the SMC website. Specifications
Load more

Recommended publications
  • An Inventory of US Navy Courses Suitable for Use in Training Civiliam
    DOCUMENT RESUME ED 118 915 CE 006 479 AUTHOR Rogers, William A., Jr.; Nisos, Michael J. TITLE An Inventory of U.S. Navy Courses Suitable for Use in Training Civiliam Personnel in Basic Technical Skills. INSTITUTION Aerospace Education Foundation, Washington, D.C.; Naval Inst., Annapolis, Md. SPONS AGENCY Maryland State Dept. of Education, Baltimore. PUB DATE 15 Apr 75 NOTE 336p. AVAILABLE. FROM For more detailed information about course contents, contact U.S. Naval Institute, Annapolis, Maryland 21402 (No price given) EDRS PRICE MF-$0.83 HC-$18.07 Plus Postage DESCRIPTORS Auto Mechanics (Occupation); Aviation Technology; *Catalogs; Construction Industry; Course Content; *Course Descriptions; *Educational Equipment; Electrical Occupations; Food Service Occupations; Marine Technicians; Medical Services; *Military Training; *Technical Education; Technical Occupations; Trade and Industrial Education IDENTIFIERS *Navy ABSTRACT An inventory of courses of study developed by the United States Navy which might be useful to other private and public institutions in training civilian students in basic technological skills is presented. Individual course reports contain the following information: course description, comments, course content (including blocks of instruction and hours), support materials,, training aids, equipment, tools, and supplies and materials. Courses are listed for the following career fields: air conditioning and refrigeration, audiovisual equipment (operation), audiovisual equipment (repair) , automotive trades, aviation trades,
    [Show full text]
  • MEASURING and MARKING Tools
    Measuring & Marking Measuring & Marking OUTLETS NATIONWIDE 522 Measuring & Marking Solutions for every aspect of measuring and marking for professionals in any business. All products are accurate to international specifications and carry our comprehensive warranty and lifetime replacement policy. 524-527 527 528-530 530-534 534-536 Tapes & Rules Measuring Wheels Squares & Bevels Measuring Gauges Dial Indicators & Stands 536 536-544 545-547 547-548 549 Counters Micrometers Verniers Calipers, Dividers & Scribers Compasses 550 551 551-553 553 554 Specialised Marking Tools Chalks, Crayons & Pencils Chalklines & Refills Marking Gauges Stencils 554-555 556 Levels Surveyors Tools Measuring & Marking AVAILABLE FROM SELECTED 523 Quick Find Index DISTRIBUTORS NATIONWIDE POWER TAPE - SOFT GRIP WITH AUTOLOCK MEASURING TAPE - RUBBER ! Magnetic hook ! Top stop secures tape in place ! Non-slip grip rubber case is robust and impact resistant ! Clearly marked blade with ! Automatic blade lock (BLADE LOCKS ITSELF WHEN PULLED OUT) metric graduations ! ! Push button retrieval Extra tough impact resistant ABS case with sure-grip ! Chrome belt clip rubber shroud ! Power return blade glides back into case automatically with smooth rewind action Code Size MTS4800 3m x 16mm Code Size MTS4805 5m x 19mm RIC4167 3m x 13mm MTS4810 7.5m x 25mm RIC4170 5m x 19mm MTS4815 10m x 25mm RIC4180 7.5m x 25mm TAPE - SHOX MEASURING TAPE - ABS ! Positive brake action locks ! Expert quality, finely engineered tapes blade solidly in hand are renowned for reliability ! Sliding end
    [Show full text]
  • For the Steel and Engineering Industries
    Marking Protective Cleaners Industrial Products & Decorative & Lubricants Packaging Coatings Product Guide - Steel and Engineering Quality products inspired by innovation designed specifi cally for the Steel and Engineering Industries. www.dymark.com.au PROTECTION From the Elements Dy-Mark’s metal protection range has been specially formulated to prevent rust and corrosion. The range is ideal for preserving and protecting both new and old metal structures in both industrial and DIY applications. Featuring premium adhesion properties and superior coverage, Dy-Mark’s Metal Protection Range ensures long lasting results whilst providing protection against the harsh Australian environment. Ph: 1300 DYMARK (396 275) Fax: 1300 360 440 [email protected] www.dymark.com.au 10623DM PRODUCT GUIDE Zinc Gal Etch Primer Zinc Rich Corrosion Inhibitive Coating Fast Drying Premium Formula 400g [Qty 12], 250ml, 500ml, 1 L, 4 L 325g [Qty 12] Features & Benefi ts Features & Benefi ts • A zinc-rich high performance coating • Provides excellent adhesion for metal surfaces • Contains 91% zinc in dry fi lm that are diffi cult to bond to • Provides true galvanic protection to steel • Protects against corrosion and iron • Fast dry product • Excellent adhesion properties • Suitable for use on aluminium, galvanised iron, • Ideal for structural steelwork in industrial new steel, alloys and non-ferrous metals environments (tanks, pipes, fences and buildings) Silver Gal Rust Reformer Anti-Corrosive Bright Silver Finish 350g [Qty 12] 350g [Qty 12] Features & Benefi
    [Show full text]
  • October 2019 Auction No
    Australian Arms Auctions Auctions Arms Australian 198 214 230 234 261 Australian Arms Auctions Auction No. 53 October 13th, 2019 13th, October 53 No. Auction Auction No. 53 October 13th, 2019 Melbourne 9 10 12 22 23 26 41 46 53 54 55 58 59 61 presenting our October 2019 Auction No. 53 Sunday 13th October at 10.00 am VIEWING: Saturday 12 noon to 5 pm & Sunday 8 am to 10 am Auctioneer: Harry Glenn HUNGARIAN COMMUNITY CENTRE 760 Boronia Road Wantirna 3152 Melway 63 F-5 Excellent onsite parking facilities available. Café available by Cheryl Savage. Try the Sunday breakfast Contacts: Roland Martyn: 0428 54 33 77 Cheryl Martyn Admin: (61) 03 9848 7951 P.O. Box 1142 Doncaster East Vic 3109 Email: [email protected] www.australianarmsauctions.com 15 % Buyers Premium + GST applies. Plus GST to any lots where indicated 1 L/R = Licence required in the State of Victoria. ALL ESTIMATES IN AUSTRALIAN DOLLARS. 1 JAPANESE TYPE 30 ARISAKA CARBINE: 6.5 Arisaka; 5 shot box mag; 18.2" barrel; f. bore; standard sights, $800 - 900 bayonet stud, sling swivels, Japanese characters & chrysanthemum; vg profiles & clear markings; 85% original military finish remaining to barrel, receiver & fittings; vg stock with minor bruising; all complete including bolt dust cover but screw missing from butt plate; no cleaning rod; gwo & vg cond. #612776 matching bolt L/R 2 JAPANESE TYPE 99 ARISAKA SHORT RIFLE: 7.7 Arisaka; 5 shot box mag; 25.2" barrel; f to g bore; standard $700 - 900 sights, bayonet stud & monopod; Japanese characters to the breech, Imperial crest removed; vg profiles & clear markings; 70% original military finish remains to barrel, receiver & fittings; vg stock with minor bruising; complete with rod, swivels & dust cover to bolt; missing 2 nose cap screws; gwo & cond.
    [Show full text]
  • INDICATIVE SYLLABUS for the TRADE of FITTER S.No
    INDICATIVE SYLLABUS FOR THE TRADE OF FITTER S.No. Trade Theory Importance of safety and general precautions observed in the in the industry/shop floor. All necessary guidance to be provided to the new comers to become familiar with the working of Industrial Training Institute system 1. including stores procedures. Soft Skills: its importance and Job area after completion of training. Introduction of First aid. Operation of electrical mains. Introduction of PPEs. Introduction to 5S concept & its application. Response to emergencies eg; power failure, fire, and system failure. Linear measurements- its units, dividers, calipers, hermaphrodite, centre punch, dot 2. punch, their description and uses of different types of hammers. Description, use and care of ‘V’ Blocks, marking off table. Bench vice construction, types, uses, care & maintenance, vice clamps, hacksaw frames and blades, specification, description, types and their uses, method of using hacksaws. 3. Files- specifications, description, materials, grades, cuts, file elements, uses. Measuring standards (English, Metric Units), angular measurements, subdivisions, try square, ordinary depth gauge, protractor- description, uses and cares. Marking off and layout tools, dividers, scribing block, odd leg calipers, punches- 4. description, classification, material, care & maintenance. Calipers- types, material, constructional details, uses, care & maintenance of cold 5. chisels- materials, types, cutting angles. Marking media, marking blue, Prussian blue, red lead, chalk and their special application, 6. description. Use, care and maintenance of scribing block. Surface plate and auxiliary marking equipment, ‘V’ block, angle plates, parallel block, description, types and uses, workshop surface plate- their uses, accuracy, care and maintenance. 7. Types of files- convexing, taper, needle, care and maintenance of files, various types of keys, allowable clearances & tapers, types, uses of key pullers.
    [Show full text]
  • Syllabus for the Trade of Fitter
    SYLLABUS FOR THE TRADE OF FITTER First Semester (Semester Code no. FTR - 01) Duration : Six Month Week Trade Practical Trade Theory No. 1. Importance of trade training, List of tools Importance of safety and general & Machinery used in the trade. precautions observed in the in the Health & Safety: Introduction to safety industry/shop floor. All necessary guidance equipments and their uses. Introduction of to be provided to the new comers to first aid, operation of Electrical mains. become familiar with the working of Industrial Training Institute system Occupational Safety & Health including stores procedures. Soft Skills: its Importance of housekeeping & good importance and Job area after completion of training. Introduction of shop floor practices. First aid. Operation of electrical mains. Health, Safety and Environment Introduction of PPEs. Introduction to 5S guidelines, legislations & regulations as concept & its application. applicable. Disposal procedure of waste Response to emergencies eg; power failure, materials like cotton waste, metal fire, and system failure. chips/burrs etc. Basic safety introduction, Personal protective Equipments(PPE):- Basic injury prevention, Basic first aid, Hazard identification and avoidance, safety signs for Danger, Warning, caution & personal safety message. Preventive measures for electrical accidents & steps to be taken in such accidents. Use of Fire extinguishers. 2. Identification of tools & equipments as per Linear measurements- its units, dividers, desired specifications for marking & calipers, hermaphrodite, centre punch, dot sawing. punch, their description and uses of Selection of material as per application different types of hammers. Description, Visual inspection of raw material for use and care of „V‟ Blocks, marking off rusting, scaling, corrosion etc., Marking table.
    [Show full text]
  • Wooden Hinges
    THE PRACTICAL SHOP WOODEN HINGES Here’s a challenging furniture detail that’s utilitarian, attractive, and all-around impressive. By Michael McDunn IF YOU’VE GOT YOUR SIGHTS SET ON MAKING HIGH- END FURNITURE, wooden hinges are an impressive detail you’ll want to master. I regularly use the type of wooden hinge described in this article when crafting Pembroke-style drop-leaf tables. If you desire a perfect match of grain across the hinge, begin with a single board that has been cut in half, and fashion the two interlocking halves of the hinges from the edges that were formerly connected. Begin with your two pieces of stock dimensioned to final thickness and width. I’m making a hinge with pieces that are ¾" thick by 3¾" wide, which will provide easy spacing for the hinge knuckles later on. It is a good idea to leave your workpieces extra- long at this point, so mistakes can be erased simply by trimming down the board. MARKING THE STOCK The success of the hinge will depend upon consistent positioning of its interlocking parts, so a common line of reference is necessary. Such a line is easily scribed TIPS for TOP-NOTCH marking A standard marking gauge can be modified by sharpening the pins to a cutting edge. The result is a much cleaner marking line, especially across the grain. Focus on keeping the head of the gauge against the workpiece, as the blade will have a tendency to follow the grain, possibly pushing the head away. Hold the gauge head gently but firmly in place.
    [Show full text]
  • Marking out Techniques
    Module Resource Manual Marking Out Techniques MEC078 SAMPLE This 1st edition published in November 2002 by Manufacturing and Engineering Division NSW TAFE Commission PO Box 218 Bankstown NSW 2200 This work is copyright. Any inquiries about the use of this material should be directed to the publisher. © New South Wales Technical and Further Education Commission 1998 National Library of Australia Publication No: ISBN 0 7348 2059 3 Marking Out Techniques MEC078 SAMPLE CONTENTS Introduction 2 Occupational Health & Safety 2 Review questions 3 To pass 3 Pre-requisites 3 Suggested references 3 Module Organiser 4 Module Sections Section 1: Tools and equipment 5 Review questions 19 Section 2: Planning 23 Review questions 45 Section 3: Marking out 48 Exercise 1 - Marking Out - 2D 53 Exercise 2 - Marking Out - 2D 55 Optional exercise 1 - Marking Out - 2D 58 Exercise 3 - Marking Out - 3D 60 Optional exercise 2 - Marking Out - 3D 63 Optional exercise 3 - Marking Out - 3D 65 Section 4: Templates 68 Exercise 4 - Template construction 71 Answers to review questions 74 Terms and Definitions 76 SAMPLE 5 MODULE SECTIONS Section 1: Tools and equipment PURPOSE In this section you will be introduced to the various tools used in marking out, their uses, how to store and handle them safely. You will also become familiar with the reasons for marking out. Objectives At the end of this section you will be able to: Name marking out tools and equipment. State the purpose of marking out tools and equipment. State the safety procedures and precautions for handling, using and storing marking out tools and equipment.
    [Show full text]
  • Structural Steel Design Awards 2016
    www.newsteelconstruction.com STRUCTURAL STEEL DESIGN AWARDS 2016 No 9 October 2016 24 Vol In this issue Cover Image Harlech Castle Footbridge Concept designer: Mott MacDonald Structural Engineer: David Dexter Associates Steelwork Contractor: S H Structures Ltd Main Contractor: RL Davies & Son Ltd Client: Cadw October 2016 Vol 24 No 9 EDITOR Editor’s comment The 2016 Structural Steel Design Awards judges saw a rise in the Nick Barrett Tel: 01323 422483 [email protected] 5 technical challenges being overcome by designers and steelwork contractors in this DEPUTY EDITOR year’s awards, writes Editor Nick Barrett. Martin Cooper Tel: 01892 538191 [email protected] PRODUCTION EDITOR News The Structural Steel Design Awards (SSDA) celebrated its 48th year with a Andrew Pilcher Tel: 01892 553147 [email protected] 6 ceremony at the Museum of London. PRODUCTION ASSISTANT Alastair Lloyd Tel: 01892 553145 [email protected] Sector Focus: Computer Software The computer software sector forms an integral COMMERCIAL MANAGER part of steel design and construction. Fawad Minhas Tel: 01892 553149 10 [email protected] NSC IS PRODUCED BY BARRETT BYRD ASSOCIATES Structural Steel Design Awards A special feature detailing all of this year’s winners ON BEHALF OF THE BRITISH CONSTRUCTIONAL 11 and shortlisted projects. STEELWORK ASSOCIATION AND STEEL FOR LIFE IN ASSOCIATION WITH THE STEEL CONSTRUCTION INSTITUTE Introduction and Judges David Lazenby, Chairman of the SSDA judging panel said it The British Constructional Steelwork Association Ltd was reassuring that there was an increase in the number of submissions for the 4 Whitehall Court, Westminster, London SW1A 2ES 12 Telephone 020 7839 8566 Awards scheme this year.
    [Show full text]
  • Material Handling Productivity Solutions
    Material Handling Productivity Solutions 2012 Catalog StoreOrganize &Transport Akro-Mils® Productivity Solutions store, organize, transport & more! Ready, Set, Organize™ . & Save! Akro-Mils is all about storage, organization and transport solutions that increase material handling efficiency and reduce costs in virtually any industry. Our broad range of products are used to shorten assembly times, maintain accurate inventories, optimize storage space and improve parts protection – all in support of Lean practices and other initiatives to increase productivity and profitability in any setting, from industrial to healthcare to retail. Simplify Organization Storage Bins – Replace the mess and expense of cardboard boxes with our wide selection of reusable bins. Simplify organization and maintain quality to improve efficiency in any operation. Improve Handling Efficiency Hand-Held Containers – Reusable containers deliver flexibility and savings. From Attached Lid to Straight Wall styles, our selection matches your needs in any industry – industrial, distribution, healthcare and more! Maximize Space Usage Bin Systems – Take back valuable floor space and improve storage efficiency with bin systems, including shelving, cabinets, Custom Products racks, rails, carts and louvered panels. You can order a variety of custom products, OEM solutions and unique merchandising systems – all from Akro-Mils! Our unrivaled production resources, dependable Move With Efficiency quality and dedicated Transport Systems – We offer a broad selection of customer service
    [Show full text]
  • Artisan Supplies Catalogue
    ARTISAN SUPPLIES CATALOGUE Knifemaking and Blacksmithing Visit our Website: www.artisansupplies.com.au CONTENTS 3. Safety Warning 47. Wilmont Grinders 4. Knife and Blade Steels, Carbon 50. Contact Wheels, Grinder Parts, Build Your Own 7. Knife and Blade Steels, Stainless 51. 123 Blocks 10. Damasteel, Premium Blade Steel and Damascus 51. Precision Parallels 18. Knife Making Kits 53. Disc Grinders 19. 416 Stainless Guard and Pin Material 54. Sharpening Systems 19. Hardware: Corby Bolts 55. Abrasives, Wet & Dry Sandpaper 20. Rivets and Screws 56. Knifemakers Hand and Pillar Files 21. Adhesives: BladeBond Epoxies 58. Abrasives: Belts 22. Guard and Fittings: Brass, Copper Bronze 64. Polishing Supplies 24. Mosaic Pins 65. Blacksmith Tools 27. Handle Materials 72. Miscellaneous 33. Paragon Heat Treating Furnaces 73. Kydex 36. Gas Forge Burners and Accessories 80. Digital Height Gauge 39. Heat Treating Accessories 81. Kant Twist Clamps 39. Heating Torches 84. Leather Working Tools and Materials 41. Radius Master Grinders 89. Other Places of Interest 44. Noob Grinders & Accessories 90. Terms and Conditions of Sale 2 Safety Warning Knifemaking, Blacksmithing and associated trades are inherently danger- ous. It is not just the obvious risks of hot metal and sharp edges, but also the far more lethal effects of dusts and fumes, and fast spinning machinery. Please ensure you assess all of the risks, obtain all relevant material safety data sheets (MSDS) and understand the materials you are work- ing with, so you can put measures in place to ensure your safety. Many timbers have carcinogenic and poisonous dust, it is considered es- sential shop practice to wear a suitable respirator/dust mask when working with all of the materials used in knife making.
    [Show full text]
  • 11407.01 GCSE Technology and Design Unit 1 Core MS Summer
    Newfi cation Speci General Certificate of Secondary Education 2018 Technology and Design Unit 1: Technology and Design Core Content [GTY11] WEDNESDAY 23 MAY, MORNING MARK SCHEME 11407.01 F General Marking Instructions Introduction Mark schemes are intended to ensure that the GCSE examinations are marked consistently and fairly. The mark schemes provide markers with an indication of the nature and range of candidates’ responses. The mark schemes should be read in conjunction with these general marking instructions. Assessment objectives Below are the assessment objectives for GCSE Technology and Design. Students must: • recall select and communicate their knowledge and understanding of technology and design in a range of contexts (AO1); • apply skills, knowledge and understanding, in a variety of contexts and in designing and making products (AO2); and • analyse and evaluate products, including their design and production (AO3). Flexibility in marking Mark schemes are not intended to be totally prescriptive. No mark scheme can cover all the responses which candidates may produce. In the event of an unanticipated answer, examiners are expected to use their professional judgement to assess the validity of answers. If an answer is particularly problematic, then examiners should seek the guidance of the Supervising Examiner. Positive Marking Examiners are encouraged to be positive in their marking, giving appropriate credit for what candidates know, understand and can do rather than penalising candidates for errors or omissions. Examiners should make use of the whole of the available mark range for any particular question and be prepared to award full marks for a response which is as good as might reasonably be expected of a 16-year-old GCSE candidate.
    [Show full text]