DOCSLIB.ORG

Virtual Inertia-Based Inverters for Mitigating Frequency Instability in Grid-Connected Renewable Energy System: a Review

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Virtual Inertia-Based Inverters for Mitigating Frequency Instability in Grid-Connected Renewable Energy System: a Review applied sciences Review Virtual Inertia-Based Inverters for Mitigating Frequency Instability in Grid-Connected Renewable Energy System: A Review Kah Yung Yap , Charles R. Sarimuthu * and Joanne Mun-Yee Lim Electrical and Computer Systems Engineering (ECSE), School of Engineering, Monash University Malaysia, 47500 Subang Jaya, Selangor Darul Ehsan, Malaysia; [email protected] (K.Y.Y.); [email protected] (J.M.-Y.L.) * Correspondence: [email protected]; Tel.: +60-3-5515-9732 Received: 15 October 2019; Accepted: 22 November 2019; Published: 5 December 2019 Abstract: This study paper presents a comprehensive review of virtual inertia (VI)-based inverters in modern power systems. The transition from the synchronous generator (SG)-based conventional power generation to converter-based renewable energy sources (RES) deteriorates the frequency stability of the power system due to the intermittency of wind and photovoltaic (PV) generation. Unlike conventional power generation, the lack of rotational inertia becomes the main challenge to interface RES with the electrical grid via power electronic converters. In the past several years, researchers have addressed this issue by emulating the behavior of SG mathematically via pulse width modulation (PWM) controller linked to conventional inverter systems. These systems are technically known as VI-based inverters, which consist of virtual synchronous machine (VSM), virtual synchronous generator (VSG), and synchronverter. This paper provides an extensive insight into the latest development, application, challenges, and prospect of VI application, which is crucial for the transition to low-carbon power system. Keywords: virtual inertia; renewable energy system; inverter; droop control; frequency stability; swing equation; grid angular frequency 1. Introduction Over the last decades, global electricity demand has increased significantly [1]. To cater to these demands, many countries are utilizing environmentally friendly power generation such as solar photovoltaic (PV) energy and wind energy. Renewable energy sources (RES) is much preferred because of its merit factors, including cost-effectiveness, energy efficiency, and sustainability [2]. The tremendous growth of RES gravitates modern power grid towards the inverter dominated power system [3], from the conventional synchronous generator (SG) rotational generator dominated power system [4]. Grid-connected or grid-tied RES is beneficial in improving the voltage profile, increasing the reliability of the power system, and controlling the active and reactive power flow [5]. Despite the numerous advantages, studies have shown that high penetration of grid-connected RES introduces critical frequency stability issues [6] and power grid security issues [7], which include the following: 1. RES exhibits low or non-existent inertial responses which lead to frequency instability [8]. 2. In the event of a fault and sudden load change, the system frequency deviates from the nominal frequency [9]. 3. The frequency nadir and rate of change of frequency (RoCoF) are expected to be higher in the event of a fault or sudden load change, which activates the load-shedding controller to trip frequency relay [10]. Appl. Sci. 2019, 9, 5300; doi:10.3390/app9245300 www.mdpi.com/journal/applsci Appl. Sci. 2019, 9, x FOR PEER REVIEW 2 of 30 Appl. Sci. 2019, 9, x FOR PEER REVIEW 2 of 30 3. The frequency nadir and rate of change of frequency (RoCoF) are expected to be higher in the Appl.3. Sci.eventThe2019 offrequency, 9 ,a 5300 fault nadiror sudden and rate load of change,change of which freque acncytivates (RoCoF) the areload-shedding expected to becontroller higher in to the2 oftrip 29 frequencyevent of relaya fault [10]. or sudden load change, which activates the load-shedding controller to trip Byfrequency interfacing interfacing relay RES RES [10]. using using a aconventional conventional inverter, inverter, it degrades it degrades the thefrequency frequency stability stability due dueto lack to oflack rotating ofBy rotating interfacing masses masses [11]. RES The [ 11using]. RES The a conventional is RES intermittent is intermittent inverter, and thus it and degrades by thus interfacing bythe interfacingfrequency RES to stability RESthe grid to due the via to grid lacka fast- via respondinga fast-respondingof rotating inverter, masses inverter, the[11]. RES The the is RES presented RES is isintermittent presented to grid asan to ad gridfast-dynamic thus as by a interfacing fast-dynamic system RES [12]. system to This the quickgrid [12]. via interaction This a fast- quick causesinteractionresponding frequency, causes inverter, phase frequency, the angle,RES is phase presentedand angle,voltage to andgrid amplitude as voltage a fast-dynamic amplitudeinstability system [13]. instability [12].It causes This [13 quick]. more It interaction causes significant more frequencysignificantcauses frequency, frequencydeviations phase deviations and transientangle, and and transientpower voltage exchange poweramplitude exchangess in instability the event in the [13]. of event aIt power causes of a power fault.more fault. Tosignificant solve To solve the problemsthefrequency problems introduced deviations introduced by and grid-connected by transient grid-connected power RES, exchange RES, virtual virtual sinertia in inertiathe (VI),event (VI), also of also aknown power known asfault. artificial as artificialTo solve inertia inertia the or syntheticorproblems synthetic inertia introduced inertia control control by strategy, grid-connected strategy, has has been been RES, proposed proposedvirtual inertia and and researched(VI), researched also known extensively extensively as artificial in conventional inertia or inverters.synthetic VI VI inertia emulates emulates control the the inertia inertiastrategy, response response has been of of a aproposed traditional traditional and synchronous synchronous researched machine machineextensively (SM) (SM) in mathematically mathematicallyconventional viainverters. pulse width VI emulates modulation the inertia (PWM). response Figure of1 1 apresents presents traditional thethe synchronous generalgeneral connectionconnection machine of of(SM) VI-basedVI-based mathematically inverterinverter inin via pulse width modulation (PWM). Figure 1 presents the general connection of VI-based inverter in grid-connected solar and wind energy. grid-connected solar and wind energy. FigureFigure 1. 1. TheThe The general general general connection connectionconnection ofof grid-co grid-connectednnected solar solar solar and and wind wind energy. energy. VI-based inverters and their control strategy can be implemented in various applications such as VI-basedVI-based inverters inverters and and their their control control strategystrategy can be implementedimplemented in in various various applications applications such such grid-connectedas grid-connected wind wind power power [14 [14,15],15] and and solar solar power power plant plant [[16],16], high voltage voltage direct direct current current (HVDC) (HVDC) as grid-connected wind power [14,15] and solar power plant [16], high voltage direct current (HVDC) transmissiontransmission [17 [17,18],,18], energy energy storage storage systemsystem (ESS), microgrid [19], [19], elec electrictric vehicle vehicle (EV) (EV) chargers chargers [20], [20 ], transmission [17,18], energy storage system (ESS), microgrid [19], electric vehicle (EV) chargers [20], staticstatic synchronous synchronous compensator compensator (STATCOM),(STATCOM), virtualvirtual inertia machine machine (VIM), (VIM), modular modular multilevel multilevel static synchronous compensator (STATCOM), virtual inertia machine (VIM), modular multilevel converterconverter (MMC)-based (MMC)-based direct direct current current (DC)(DC) systemsystem [2 [211],], electronic electronic appliances, appliances, and and flexible flexible loads loads to to converter (MMC)-based direct current (DC) system [21], electronic appliances, and flexible loads to supportsupport frequency frequency stability. stability. Figure Figure2 presents 2 presents the applicationthe application and implementationand implementation of VI of in theVI in modern the support frequency stability. Figure 2 presents the application and implementation of VI in the powermodern system. power system. modern power system. VI emulation VItechniques emulation techniques Energy VI-based StorageEnergy Units InvertersVI-based Storage Units Inverters DC-link Capacitors Batteries VSM Capacitors DC-link Capacitors Batteries VSM Capacitors Supercapacitors VSG Supercapacitors VSG Ultracapacitors Synchronverter Ultracapacitors Synchronverter Figure 2. The implementations of VI emulation technique. Figure 2. The implementations of VI emulation technique. Appl. Sci. 2019, 9, x FOR PEER REVIEW 3 of 30 Appl. Sci. 2019, 9, 5300 3 of 29 As the amount of solar and wind energy generation increases, grid-connected RES requires VI emulation,As the and amount thus ofVI-related solar and publication wind energy and generation research are increases, increasing grid-connected [22]. There are RES limited requires studies VI emulation,that compare and VI-based thus VI-related inverters, publication namely virtual and research synchronous are increasing generator [22 (VSG),]. There virtual are limited synchronous studies thatmachine compare (VSM) VI-based and synchronverter, inverters, namely concerning virtual synchronoustheir technical generator implementati (VSG),ons, virtual merits, synchronous demerits,
Load more

Recommended publications
  • Load Reduction, Demand Response and Energy Efficient Technologies and Strategies
    PNNL-18111 Prepared for the U.S. Department of Energy under Contract DE-AC05-76RL01830 Load Reduction, Demand Response and Energy Efficient Technologies and Strategies PA Boyd GB Parker DD Hatley November 2008 PNNL-18111 Load Reduction, Demand Response and Energy Efficient Technologies and Strategies PA Boyd GB Parker DD Hatley November 2008 Prepared for the U.S. Department of Energy under Contract DE-AC05-76RL01830 Pacific Northwest National Laboratory Richland, Washington 99352 Executive Summary The Department of Energy‟s (DOE‟s) Pacific Northwest National Laboratory (PNNL) was tasked by the DOE Office of Electricity (OE) to recommend load reduction and grid integration strategies, and identify additional demand response (energy efficiency/conservation opportunities) and strategies at the Forest City Housing (FCH) redevelopment at Pearl Harbor and the Marine Corps Base Hawaii (MCBH) at Kaneohe Bay. The goal was to provide FCH staff a path forward to manage their electricity load and thus reduce costs at these FCH family housing developments. The initial focus of the work was at the MCBH given the MCBH has a demand-ratchet tariff, relatively high demand (~18 MW) and a commensurate high blended electricity rate (26 cents/kWh). The peak demand for MCBH occurs in July-August. And, on average, family housing at MCBH contributes ~36% to the MCBH total energy consumption. Thus, a significant load reduction in family housing can have a considerable impact on the overall site load. Based on a site visit to the MCBH and meetings with MCBH installation, FCH, and Hawaiian Electric Company (HECO) staff, the following are recommended actions – including a “smart grid” recommendation – that can be undertaken by FCH to manage and reduce peak-demand in family housing.
    [Show full text]
  • SMART GRIDS and RENEWABLES: a Guide for Effective Deployment TABLE of CONTENTS
    IRENA International Renewable Energy Agency SMART GRIDS AND RENEWABLES A Guide for Effective Deployment Working Paper Working November 2013 Copyright © IRENA 2013 Unless otherwise indicated, material in this publication may be used freely, shared or reprinted, so long as IRENA is acknowledged as the source. About IRENA The International Renewable Energy Agency (IRENA) is an intergovernmental organisation that supports countries in their transition to a sustainable energy future, and serves as the principal platform for international cooperation, a centre of excel- lence, and a repository of policy, technology, resource and financial knowledge on renewable energy. IRENA promotes the widespread adoption and sustainable use of all forms of renewable energy, including bioenergy, geothermal, hydropower, ocean, solar and wind energy in the pursuit of sustainable development, energy access, energy security and low-carbon eco- nomic growth and prosperity. www.irena.org Acknowledgements The work for the preparation of this paper was led by Paul Komor and Anderson Hoke, University of Colorado, Boulder, Colo- rado, USA. The paper benefitted from very valuable comments from Rainer Bacher (Bacher Energie, Switzerland), Melissa Chan (Navigant Consulting, USA), Kazuyuki Takada (New Energy and Industrial Technology Development Organization, Japan), Matt Wakefield (EPRI, USA). Authors: Ruud Kempener (IRENA), Paul Komor and Anderson Hoke (University of Colorado) For further information or to provide feedback, please contact: Ruud Kempener, IRENA Innovation and Technology Centre. E-mail: [email protected] or [email protected]. Disclaimer The designations employed and the presentation of materials herein do not imply the e xpression of any opinion whatsoever on the part of the International Renewable Energy Agency concerning the legal status of any country, territory, city or area, or concerning their authorities or the delimitation of their frontiers or boundaries.
    [Show full text]
  • Grid Integration of Large-Capacity Renewable Energy Sources and Use of Large-Capacity Electrical Energy Storage
    grid stability – power integration – battery – energy-generation – ywheel – decarbonization – energy security – wind – solar – variability – unpredictability – dependency – photovoltaic – UHVDC – control – pumped storage - exibility – assessment – planning – storage technologies – generation forecast – operational enhancement - demand response – modeling – electrical energy storage – alternating current – contingency analysis – direct current – induction generator – transmission network – energy eciency – heat recovery – electrotechnology – analysis – strategy – electricity market – renewables – energy access – grid operator – grid infrastructure – synthesis – impact – coordination® – energy market operators – transmission planning body – challenges – standards – hydrogen – policy-makers – regulators – industry – research community – energy access – grid architecture – zero-fuel-cost – energy cost – interconnection – power uctuations – black-out – geopolitics – distribution – utility – SCADA – generation portfolio – grid operation – hydro – variable generation – steam – solar concentrating power – PV – intermittency – location – dependent – grid owner – wind speed – supply and demand – voltage support – forecast – weather – dispatchable load – nuclear – transmission capacity – sunlight – load management – voltage control – frequency regulation – spinning reserve – black-start capacity – Smart Grid – remote locations – uncertainty – deterministic – complexity – micro-grid – power output – power conversion – steam turbine – thermal energy
    [Show full text]
  • Materials Research for Smart Grid Applications
    Materials Research for Smart Grid Applications Steve Bossart & Ryan Egidi Energy Analysts U.S. Department of Energy National Energy Technology Laboratory Materials Challenges in Alternative & Renewable Energy February 26 – March 1, 2012 Smart Grid Topics • Drivers & Value Proposition • Concepts • Technologies • Applications • Relationship to Materials Research • Metrics & Benefits • Implementation Challenges • Deployment and Demonstration Status 2 Drivers and Value Proposition 3 Why Modernize the Grid? • Today’s grid is aging and outmoded • Unreliability is costing consumers billions of dollars • Today’s grid is vulnerable to attack and natural disaster • An extended loss of today’s grid could be catastrophic to our security, economy and quality of life • Today’s grid does not address the 21st century power supply challenges • Adverse trends associated with the grid - Costs, reliability, peak loads, asset underutilization, TLRs, grid divorce • The benefits of a modernized grid are substantial 4 4 4 Value Proposition Cost to Modernize Benefit of Modernization • $338-$476B over 20 years • $1294 – 2028 Billion – $ 82-90 B for transmission • Overall benefit-to-cost ratio – $232-$339 B for distribution of 2.8 to 6.0 – $24-46 B for consumer • $17-24 B per year EPRI, 2011 Previous Studies Benefit to Cost Ratio for West Virginia of 5:1 Benefit to Cost Ratio for San Diego of 6:1 Benefit to Cost Ratio for EPRI (2004) 4:1-5:1 $165 B Cost $638 - $802 B Benefits EPRI Report: http://www.smartgridinformation.info/pdf/3272_doc_1.pdf 5 5 Definitions and
    [Show full text]
  • Part II. Grid Friendly™ Appliance Project
    Pacific Northwest GridWise™ Testbed Demonstration Projects Part II. Grid Friendly™ Appliance Project DJ Hammerstrom, Principal Investigator J Brous TA Carlon DP Chassin C Eustis GR Horst OM Järvegren R Kajfasz W Marek P Michie RL Munson T Oliver RG Pratt October 2007 Prepared for the U.S. Department of Energy under Contract DE-AC05-76RL01830 DISCLAIMER This report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor Battelle Memorial Institute, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any agency thereof, or Battelle Memorial Institute. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof. PACIFIC NORTHWEST NATIONAL LABORATORY operated by BATTELLE for the UNITED STATES DEPARTMENT OF ENERGY under Contract DE-AC05-76RL01830 Printed in the United States of America Available to DOE and DOE contractors from the Office of Scientific and Technical Information, P.O. Box 62, Oak Ridge, TN 37831-0062; ph: (865) 576-8401 fax: (865) 576-5728 email: [email protected] Available to the public from the National Technical Information Service, U.S.
    [Show full text]
  • Foundations and Challenges of Low-Inertia Systems (Invited Paper)
    Foundations and Challenges of Low-Inertia Systems (Invited Paper) Federico Milano Florian Dorfler¨ and Gabriela Hug David J. Hill∗ and Gregor Verbicˇ University College Dublin, Ireland ETH Zurich,¨ Switzerland University of Sydney, Australia email: [email protected] emails: dorfl[email protected], ∗ also University of Hong Kong [email protected] emails: [email protected], [email protected] Abstract—The electric power system is currently undergoing support. This may create unexpected couplings and control a period of unprecedented changes. Environmental and sustain- approaches based on time-scale separations may become more ability concerns lead to replacement of a significant share of brittle and increasingly less valid. Likewise, system control conventional fossil fuel-based power plants with renewable energy tasks predominantly provided by synchronous generators (such resources. This transition involves the major challenge of substi- as voltage support and oscillation damping) have to be increas- tuting synchronous machines and their well-known dynamics and ingly shouldered by non-synchronous devices. controllers with power electronics-interfaced generation whose regulation and interaction with the rest of the system is yet to be Large-scale low inertia power systems have been merely a fully understood. In this article, we review the challenges of such theoretical concept up until just a decade ago but have now low-inertia power systems, and survey the solutions that have been become a reality. Some countries already have solar and/or put forward thus far. We strive to concisely summarize the laid- wind generation capacity able to cover more than 100% of out scientific foundations as well as the practical experiences of the demand.
    [Show full text]
  • Simulation Framework for Demand Response Analysis and Control System
    Demand Response Analysis and Control System Simulation Framework Simulation Framework for Demand Response Analysis and Control System Prepared For: California Institute for Energy and Environment University of California Office of the President In Response To: Research Opportunity Notice DR ETD-02-01 Lead authored by: Oak Ridge National Laboratory 1 Bethel Valley Rd. Oak Ridge, TN 37931 Phone: +1-865-574-2704 Fax: +1-865-576-0003 July, 2009 Document: SIM-FRAMEWORK - DRACS CIEE Author: Arjun Shankar, James Nutaro, Glenn Allgood, Mohammed Olama Page 1 of 38 Demand Response Analysis and Control System Simulation Framework Document History Revision History Revision Revision Revision / Summary of Changes Changes Number Date Reviewed marked By 1.0 051009 Arjun Shankar Original Document 1.1 052009 Arjun Shankar Added sections and initial case study draft and Contributors 1.2 061509 Jim Nutaro/Arjun Case Study Details, Simulation components Shankar 1.3 063009 Arjun Shankar Second Case Study Details, Smoothing Text 1.4 070409 Jim Nutaro Updated Case Study 1.5 071109 Arjun Shankar Revisions with case study and write-ups overall 2.0 071509 Arjun Shankar Final revision Document: SIM-FRAMEWORK - DRACS CIEE Author: Arjun Shankar, James Nutaro, Glenn Allgood, Mohammed Olama Page 2 of 38 Demand Response Analysis and Control System Simulation Framework Contents 1. Introduction and Background ................................................................................. 5 1.1 Document Context .........................................................................................................................
    [Show full text]
  • A Policy for the 21St Century Grid: Enabling Our Secure Energy Future
    A POLICY FRAMEWORK FOR THE 21st CENT URY GR ID: Enabling Our Secure Energy Future JUNE 2011 EXECUTIVE OFFICE OF THE PRESIDENT NATIONAL SCIENCE AND TECHNOLOGY COUNCIL WAS HIN GTON , D C. 20502 June 13,2011 Dear Colleagues: We are pleased to transmit the report "A Policy Framework for the 21 sl Century Grid: Enabling Our Secure Energy Future." This report outlines policy recommendations that build upon the Energy Independence and Security Act of 2007 and the Obama Administration's smart grid investments to foster long-term investment, job growth, innovation, and help consumers save money. The report was prepared by the Subcommittee on Smart Grid of the National Science and Technology Council, Committee on Technology. A 21 SI century electric system is essential to America's ability to lead the world and create jobs in the clean-energy economy of the future. The Administration has made unprecedented investments in clean-energy technologies and grid modernization. For example, as part of the Recovery Act, the Nation invested more than $4.5 billion for electricity delivery and energy reliability modernization. This report highlights further efforts that are needed to take advantage of opportunities made possible by modern information, energy, and communications technology. It also provides a policy framework that promotes cost-effective investment, fosters innovation to spur the development of new products and services, empowers consumers to make informed decisions with better energy information, and secures the grid against cyber attacks. Facilitating a smarter and more secure grid will require sustained cooperation among the private sector, state and local governments, the Federal Government, consumer groups, and other stakeholders.
    [Show full text]
  • 3D Flexible and Distributed Energy Resources
    Quadrennial Technology Review 2015 Chapter 3: Enabling Modernization of the Electric Power System Technology Assessments Cyber and Physical Security Designs, Architectures, and Concepts Electric Energy Storage Flexible and Distributed Energy Resources Measurements, Communications, and Controls Transmission and Distribution Components U.S. DEPARTMENT OF ENERGY Quadrennial Technology Review 2015 Flexible and Distributed Energy Resources Chapter 3: Technology Assessments Introduction The U.S. electric power system is undergoing significant changes. The reliance on large thermal generators of the past is giving way to a much more dynamic paradigm. In recent years, many new technologies have been connected to the traditional grid, including variable wind generators, plug-in electric vehicles, photovoltaic systems, fuel cells, microturbines, demand response and load modifying resources, and energy storage systems. This white paper examines the state of these technologies that reside at the “edges” of the grid—including flexible bulk generation and customer-sited distributed resources—that can be advanced to provide increased system flexibility. Emerging professional standards, such as the Institute of Electrical and Electronic Engineers (IEEE) Standard for Interconnecting Distributed Resources with Electric Power Systems (IEEE 1547), are defining the requirements that these technologies must meet in order to safely and reliably interconnect. These standards address issues (such as low voltage ride-through, harmonic injection, and volt/VAR control) to ensure that new technologies do not jeopardize the safety or reliability of the electric power system. Strategic integration of clean energy technologies and distributed energy resources (DERs) not only requires interconnection but also maximizes the benefit these technologies and resources can provide to society while supporting secure and reliable electric power system operations.
    [Show full text]
  • Advanced Metering Infrastructure (AMI)
    Table of Contents Executive Summary ............................................................................................................................4 Major Findings .............................................................................................................................................. 4 Key Lessons and Conclusions ....................................................................................................................... 6 Future Directions and Next Steps ................................................................................................................ 8 1 AMI and Customer System Deployment in the Smart Grid Investment Grants ..................................9 1.1 AMI and Customer Technologies and Functions Deployed in SGIG ........................................................... 10 Advanced Metering Infrastructure............................................................................................................. 11 Customer Systems ...................................................................................................................................... 15 Time-Based Rates and Demand-Side Programs ......................................................................................... 16 1.2 Project Build and Impact Metrics ............................................................................................................... 17 1.3 Key Data Limitations and Considerations .................................................................................................
    [Show full text]
  • Frequency Responsive Demand
    PNNL-23764 Loads as a Resource Frequency Responsive Demand September 2014 K Kalsi M Elizondo J Lian W Zhang LD Marinovici C Moya PNNL-23764 PNNL-23764 Frequency Responsive Demand K Kalsi M Elizondo J Lian W Zhang LD Marinovici C Moya September 2014 Prepared for the U.S. Department of Energy under Contract DE-AC05-76RL01830 Pacific Northwest National Laboratory Richland, Washington 99352 Executive Summary Frequency control plays an important role in preserving the power balance of a multi-machine power system. Generators modify their power output when a non-zero frequency deviation is presented in order to restore power balance across the network. However, with plans for large-scale penetration of renewable energy resources, performing primary frequency control using only supply-side resources becomes not only prohibitively expensive, but also technically difficult. Frequency control from the demand side or load control presents a novel and viable way for providing the desired frequency response. Loads can measure frequency locally and change their power consumption after a non-zero frequency deviation is presented in order to achieve power balance between generation and consumption. The specific objectives of this project are to: Provide a framework to facilitate large-scale deployment of frequency responsive end-use devices Systematically design decentralized frequency-based load control strategies for enhanced stability performance Ensure applicability over wide range of operating conditions while accounting for unpredictable end-use behavior and physical device constraints Test and validate control strategy using large-scale simulations and field demonstrations Create a level-playing field for smart grid assets with conventional generators Next, a brief recap of FY12 and FY13 activities is presented followed by the progress made on the FY14 tasks.
    [Show full text]
  • An Introduction to Smart Grid Outline
    An Introduction to Smart Grid CS 687 University of Kentucky Fall 2015 Acknowledgment: These slides have used resources (documents, pictures) available on the web (including, but not limited to DoE and NIST websites) and presentations by others. Special thanks are given to Prof. Paul A. Dolloff (Univ. of Kentucky) and Prof. Peng Zhang (Tennessee Tech). Outline • Why Smart Grid? • What is Smart Grid? • Key Technologies of Smart Grid • NIST Framework • Examples 1 The Traditional Power Grid http://oncor.com/images/content/grid.jpg Nationwide Grid 2 Kentucky Transmission One-Line Diagram The case for REVITALIZATION 3 The case for REVITALIZATION The story goes like this: • If Alexander Graham Bell were somehow transported to the 21st century, he would not begin to recognize the components of modern telephony – cell phones, texting, cell towers, PDAs, etc. • while Thomas Edison, one of the grid’s key early architects, would be totally familiar with the grid. Why Smart Grid? • RELIABILITY: There have been five massive blackouts over the past 40 years, three of which have occurred in the past nine years. Today’s electricity system is 99.97 percent reliable, yet still allows for power outages and interruptions that cost Americans at least $150 billion each year. • EFFICIENCY: If the grid were just 5% more efficient, the energy savings would equate to permanently eliminating the fuel and greenhouse gas emissions from 53 million cars. • SECURITY: The interdependencies of various grid components can bring about a domino effect. 4 Why Smart Grid? (cont) • ENVIRONMENT/CLIMATE CHANGE: The United States accounts for only 4% of the world’s population and produces 25% of its greenhouse gases.
    [Show full text]