DOCSLIB.ORG

HEI System - Description and Diagnosis Chart

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
HEI System - Description and Diagnosis Chart HEI System - Description and Diagnosis Chart No. T -36 February, 1978 The High Energy Ignition System (HEI) In 1974 General Motors began equipping passenger cars and light trucks with an electronic ignition system called High Energy Ignition (HEI). The HEI is different in many ways from the previously standard breaker-point ignition system . ^ Higher available secondary voltage of 35,000 volts. ^ The secondary spark plug wires are larger diameter with silicone rubber insulation. This type of wire minimizes cross firing or arching between wires. The silicone insulation is softer than rubber insulation, so wires should be routed to avoid chafing on the engine or accessories. The insulation should never be punctured with sharp tools. The boots fit tightly on the spark plug insulators and are thus sometimes difficult to remove from the spark plugs. Tools are available from several tool companies to make removal easier. ^ Distributor cap and rotor are made of special material to handle the higher secondary voltage. ^ An internal condenser is for reducing radio interference and is not a normal replacement item. ^ There is no resistance wire or ballast resistor between the ignition switch and the coil. The system operates on full battery voltage. Zoom Sized for Print ^ The ignition coil is mounted in the distributor cap on most engines. Figure 1. ^ Some 4-cylinder and L-6-cylinder ignition coils are mounted outside of the distributor but are different in appearance from previously standard ignition coils. Zoom Sized for Print ^ Breaker points are no longer used, so point maintenance and replacement is eliminated. Instead of breaker points, a magnetic pickup and an electronic module are used. Figure 3. ^ The connector on the distributor includes a spade terminal for connecting a service tachometer. Some tachometers should be connected to this terminal and ground, others to battery positive, some will not work at all. Refer to manufacturer's instructions for the equipment used. A spade terminal female connector with the wire-end bent 90°makes a simple adapter for connecting a tachometer. The tachometer terminal on the distributor cap must never be grounded. This could damage the electronic circuitry of the module. ^ Distributors with the integral coil have no external secondary connections to attach a pickup for an oscilloscope. An inductive pickup that fits the top of the distributor cap must be used to pick up secondary impulses from the coil. Refer to the manufacturer's instructions for the equipment used. Secondary pickup on distributors with separate coil is the same as standard ignition systems . ^ Oscilloscope patterns from an HEI System may vary among different makes of oscilloscopes. Check the manufacturer's published patterns when using an oscilloscope. Diagnosis For diagnosis of the HEI System, follow the charts with the appropriate heading for the problem being experienced. These charts cover problems in the ignition system only. Do not overlook other systems such as fuel and carburetion, valves, engine compression, etc., that might cause the same complaint. A High Energy Ignition Analyzer J-24642 is available from: Kent-Moore Tool Division 28635 Mound Road Warren, Michigan 48092 If this tester is available, it should be used to determine if the module needs replacing. Operating instructions are provided with the tester. The calibrated spark gap tester used in these procedures is available from Kent-Moore Tool Division (J-26792) as well as AC-Delco outlets (ST-125). DIAGNOSIS CHARTS Introduction Decision Trees And Tables Zoom Sized for Print Typical Symbols Used In Diagnostic Charts Zoom Sized for Print This section presents a systematic method of diagnosing and troubleshooting the High Energy Ignition system . The charts you will be using are different from the ones you have used before. They aren't "go - no go" decision trees or tables. Instead the new diagnosis and troubleshooting charts use pictures plus a few words to help you solve a problem, and symbols have replaced words. Using the Charts The charts are divided into three sections: step, sequence and result. Zoom Sized for Print Zoom Sized for Print A sequence could be checking the battery lead terminal on the distributor . Each sequence ends with a result and tells you the next step to go to. Work through each step of the diagnosis and trouble- shooting charts until the system is repaired. Zoom Sized for Print To find where parts are located in the system just look at the parts locator chart: Engine Cranks But Will Not Start Or Runs Rough Or Cuts Out Zoom Sized for Print Engine Cranks But Will Not Start (Continued) Zoom Sized for Print Engine Cranks But Will Not Start (Continued) Zoom Sized for Print Problem: Engine Cranks But Will Not Start Or Runs Rough Or Cuts Out (Separate Coil) Problem: Engine Cranks But Will Not Start Or Runs Rough Or Cuts Out (Integral Coil) Engine Cranks But Will Not Start Or Runs Rough (Separate Coil) Zoom Sized for Print Tools Required: Engine Cranks But Will Not Start Or Runs Rough Or Cuts Out - Integral Coil Zoom Sized for Print Engine Cranks But Will Not Start (Continued) Zoom Sized for Print Engine Cranks But Will Not Start (Continued) .
Load more

Recommended publications
  • Bibliography on Ignition and Spark-Ignition Systems
    Bibliography on Ignition and Spark-Ignition Systems U.S. Department of Commerce National Bureau of Standards Miscellaneous Publication 251 ; THE NATIONAL BUREAU OF STANDARDS Functions and Activities The functions of the National Bureau of Standards include the developm and maintenance of the national standards of measurement and the provision of means and methods for making measurements consistent with these standards; the determination of physical constants and properties of materials ; the develop- ment of methods and instruments for testing materials, devices, and structures advisory services to government agencies on scientific and technical problems; invention and development of devices to serve special needs of the Government;I and the development of standard practices, codes, and specifications, including assistance to industry, business and consumers in the development and accepi ance of commercial standards and simplified trade practice recommendation!I The work includes basic and applied research, development, engineering, instru- mentation, testing, evaluation, calibration services, and various consultation andd information services. Research projects are also performed for other govern- ment agencies when the work relates to and supplements the basic program of the Bureau or when the Bureau's unique competence is required. The scope of activities is suggested by the listing of divisions and sections on page 26. Publications The results of the Bureau's research are published either in the Burea>au'g own series of publications or in the journals of professional and scientific societies. The Bureau itself publishes three periodicals available from the Gov- ernment Printing Office: The Journal of Research, published in four separai sections, presents complete scientific and technical papers ; the Technical Ne Bulletin presents summary and preliminary reports on work in progress ; a Central Radio Propagation Laboratory Ionospheric Predictions provides da for determining the best frequencies to use for radio communications througho the world.
    [Show full text]
  • Automotive Ignition Coil: Progress Through Efficiency
    Automotive Ignition Coil: Progress Through Efficiency he automotive ignition sys- tem is crucial to the internal Tcombustion engine’s operation and efficiency. At the heart of the entire ignition system is the ignition coil. To understand how ignition coils operate, it is important to have a general understanding of the basic principles of vehicle electronics. Direct Current (DC) vs. Alternating Current (AC) The primary winding of the For many years, this interruption ignition coil is wound with a small of the primary current was accom- number of turns creating a small plished by mechanically opening resistance. Applying battery volt- a contact called the “points” in a age to this coil causes a sizable DC synchronized sequence to send current to flow. The secondary coil high voltage pulses through a rotary has a much larger number of turns switch called the “distributor” to the and therefore acts as a step-up sparkplugs. One of the drawbacks of transformer. Rather than operating this process was that the interruption on AC voltages, this secondary of current in the primary coil generat- coil is designed to produce a large ed an inductive back-voltage in that voltage spike when the current in coil which tended to cause sparking the primary coil is interrupted. Since across the points. The system was the induced secondary voltage is improved by placing a sizable capac- proportional to the rate of change of itor across the contacts so that the the magnetic field through it, opening voltage surge tended to charge the a switch quickly in the primary circuit capacitor rather than cause destruc- FARADAY’S LAW AND to drop the current to zero will gener- tive sparking across the contacts.
    [Show full text]
  • Spark Your Interest
    Simply put, an ignition system activates a fuel-air mixture to create energy. The first ignition system to use an electric spark is thought to be Alessandro Volta’s toy electric pistol, ca. 1780. We’ve come a long way since that toy pistol! Today, the most commonly used ignition is the 4-stroke internal combustion system found in almost all vehicles, including your Corvette. Mid America Motorworks takes a look at the evolution of the ignition system, from early vehicles to the powerhouse Corvettes of today. Ignition – Why You Need A Spark Stroke 1: The piston’s Intake Valve opens to suck fuel and In a 4-stroke internal combustion system, the spark is air into the cylinder. where the magic happens. The spark ignites the air-fuel Stroke 2: The Intake Valve closes capturing the fuel and air. mixture to create a burst of energy that moves your Corvette The engine compresses the mixture, creating a large amount down the road. Just as the name implies, this happens in a of potential energy. sequence of 4 steps that continually repeat. • SPARK: When the piston reaches the top of the cylinder, the spark from the spark plug causes the mixture to explode. Camshaft Spark Plug Valve Spring Stroke 3: The explosion forces the piston back downward, Cam Mixture In releasing the potential energy as power. Stroke 4: The Exhaust Valve opens and the piston forces Cylinder Head exhaust out of the cylinder. Exhaust Valve Intake Valve Combustion Cooling Water Chamber Piston Cylinder Block Crankcase Connecting Rod Crankshaft Air Intake Compression Combustion Exhaust Emission The Main Components Distributor Spark Plug Wires The Distributor routes high voltage from the ignition coil Spark Plug Wires deliver the voltage to the Spark Plug, to the spark plugs in the correct firing order.
    [Show full text]
  • Spark Your Interest
    Simply put, an ignition system activates a fuel-air mixture to create energy. The first ignition system to use an electric spark is thought to be Alessandro Volta’s toy electric pistol, ca. 1780. We’ve come a long way since that toy pistol! Today, the most commonly used ignition is the 4-stroke internal combustion system found in almost all vehicles, including your Corvette. Mid America Motorworks takes a look at the evolution of the ignition system, from early vehicles to the powerhouse Corvettes of today. Ignition – Why You Need A Spark Stroke 1: The piston’s Intake Valve opens to suck fuel and In a 4-stroke internal combustion system, the spark is air into the cylinder. where the magic happens. The spark ignites the air-fuel Stroke 2: The Intake Valve closes capturing the fuel and air. mixture to create a burst of energy that moves your Corvette The engine compresses the mixture, creating a large amount down the road. Just as the name implies, this happens in a of potential energy. sequence of 4 steps that continually repeat. • SPARK: When the piston reaches the top of the cylinder, the spark from the spark plug causes the mixture to explode. Camshaft Spark Plug Valve Spring Stroke 3: The explosion forces the piston back downward, Cam Mixture In releasing the potential energy as power. Stroke 4: The Exhaust Valve opens and the piston forces Exhaust Valve Cylinder Head exhaust out of the cylinder. Intake Valve Intake Valve Combustion Cooling Water Chamber Piston Cylinder Block Crankcase Connecting Rod Crankshaft Air Intake Compression Combustion Exhaust Emission The Main Components Distributor Spark Plug Wires The Distributor routes high voltage from the ignition coil Spark Plug Wires deliver the voltage to the Spark Plug, to the spark plugs in the correct fi ring order.
    [Show full text]
  • Ignition Timing,” in This Section
    IGNITION SYSTEM SERVICE MANUAL NUMBER 26 Specifications Timing Timing (At Idle rpm) 1 1 BTDC 2 / 1 ATDC 3 / 2 ATDC 4 1Timing must be set using a special procedure as outlined in this section. Timing cannot be properly set using the conventional method. 2Serial number break: 0L096999 and below 3Serial number break: 0L097000 - 0L0340999 4Serial number break: 0L341000 and above. Spark Plugs Spark Plug Gap .035 In. (0.9 mm) AC-MR43LTS 3.0L NGK-BPR6EFS Champion RS12YC GM 4-Cylinder In-line Firing 50683 Firing Order 1-3-4-2 Page 4B-4 90-861329--1 MARCH 1999 SERVICE MANUAL NUMBER 26 IGNITION SYSTEM Description EST or Electronic Spark Timing is a High Energy Ignition System (HEI). The distributor itself has no centrifugal advance mechanism or devices. The spark plug wires are a carbon-impregnated cord conductor with a silicone rubber jacket. It is important they be handled with care, and routed so as not to cross each other or to be in contact with other parts of the engine to prevent rubbing. The EST System uses a square coil with epoxy covered windings to protect against mois- ture and arc-over. The timing cannot be set the same way that other ignition systems were. b c e d a f 70106 a - Distributor with Spark Plug Wires b - Wires (WHITE) Used in Timing Procedure c - Wire from Shift Interrupt Switch d - Distributor Harness e - Engine Harness Wire (PURPLE AND GRAY) f - Coil EST uses a magnetic pulse generator and an electronic module to primary circuit current. Internally the Pulse Generator, or magnetic pick-up assembly, takes the place of conven- tional points.
    [Show full text]
  • Optronic Description
    Section A1 49 - 51 Tiverton Street London SE1 6NZ United Kingdom Tel: (44) 20 7403 4334 Fax: (44) 20 7368 1270 [email protected] www.autocar-electrical.com ã OPTRONIC & PERFORMANCE IGNITION SYSTEMS Product Guide and System Component Description Contents; Page no Introduction A1.2 The Optronic System A1.2 The Performance Ignition System A1.2 Optical Switches A1.3 Marine Ignition Options A1.4 Fitting Kits A1.4 Please check for product bulletins and updated information relating to Lumenition Optronic Ignition systems at the end of this document. Website www.autocar-electrical.com Copyright ©2006 Autocar Electrical Equipment Co. Ltd. London UK No unauthorised editing or copying permitted Lumenition Ignition System Description Lumenition optically-switched contact breaker replacement ignition systems consist of two basic models, the Optronic ignition system and the Performance Ignition system. The installation of both systems is straight forward and easily reversible, involves no specialist tools and is normally completed in less than an hour. Both systems replace the distributor contact breakers with an optical switch (using a separate, distributor-specific fitting kit) and an external power module. The same distributor-specific fitting kit is used for both models and the optical switches differ only in the connectors used with the different power modules (see below) The system works by creating a beam of light inside the distributor which is broken by a fan-like part (called a chopper) fitted over the distributor cam. As the distributor cam rotates, the chopper breaks the beam of light and the optical switch and external power module fires the coil.
    [Show full text]
  • Fiero Ignition Systems
    Fiero Ignition Systems January 20, 2018 Rock Chevrolet Northern Illinois Fiero Enthusiasts Presented by Art Hall and Ray Dyreson 1 The Stock Fiero has Two Types of Ignition Systems Distributor 4 cyl: 84, 85-86 6 cyl: 85-88 Direct Ignition System (DIS) 4 cyl: 87-88 2 Types of Automotive Ignition Systems • Distributor • Mechanical Points • Electronic Ignition (EI) • Direct Ignition System (DIS) or Distributorless or Waste-Spark Ignition • Coil on Plug (COP) • Coil Near Plug (CNP) 3 To Understand Ignition Systems it Would Be Good to Understand Automotive Wiring Diagrams 4 Components have unique symbols, but many times they are also called out directly. Switches, electronic modules, lights, coils 5 Dashed lines indicate that only part of the component is represented in this diagram. This same component will be seen on other diagrams. A solid line indicates the entire component is shown 6 Wire size is given in cross-section area in sq. mm. Wire insulation color is given along with any trace or stripe color. mm2 AWG 0.5 20 0.8 18 1.0 16 2.0 14 3.0 12 5.0 10 8.0 8 13.0 6 19.0 4 32.0 2 52.0 0 7 G, C, S, followed by 3 digits are a specific ground, connector, or splice. The 3 digits give an indication of its location. 100-199 Under Hood 200-299 Under Dash Right of the 300-399 Pass. Compart. wire color is 400-499 Trunk the circuit no. Male / Female Connectors Does not apply to Fieros! Per Fiero Service Manual (?) 200-299 Pass.
    [Show full text]
  • Engine Performance
    4 Engine Performance Chapter 21 ■ Ignition To have an efficient running engine, there must be the Systems correct amount of fuel mixed with the correct amount ■ Chapter 22 Ignition System of air. These must be present in a sealed container and Service shocked by the right amount of heat, at the correct Chapter 23 ■ Fuel Systems time. With total efficiency, the engine would burn all Chapter 24 ■ Fuel System Diagnosis and Service the fuel it receives and would release extremely low Chapter 25 ■ Carburetors amounts of pollutants in its exhaust. Although total Chapter 26 ■ Carburetor efficiency is not possible at this time, late-model Diagnosis and Service engines emit very low amounts of pollutants, thanks to ■ Chapter 27 Fuel Injection emission control devices. Chapter 28 ■ Fuel Injection Diagnosis and Service To have highly efficient engines, the basic engine needs Chapter 29 ■ Emission highly efficient ignition, fuel, and emission control sys- Control Systems tems. Although there are many different designs of ■ Chapter 30 Emission these systems, the designs are similar in operation. Control Diagnosis and Service Engine performance systems are some of the most tech- Chapter 31 ■ On-Board Diagnostic Systems nologically advanced systems found on modern vehi- Chapter 32 ■ On-Board cles. They all rely on a network of input sensors and Diagnostic System Diagnosis output devices and tie directly into the electronic and Service engine control system. Mastery of these systems is nec- WE ENCOURAGE essary for an automotive technician. PROFESSIONALISM The material in Section 4 matches the content areas of the ASE certification test on engine performance and THROUGH TECHNICIAN sections of the certification test on engine repair.
    [Show full text]
  • DIGITAL FUEL INJECTION • Generation 7+ Fuel Injection Systems
    DIGITAL FUEL INJECTION • Generation 7+ Fuel Injection Systems • Generation 7+ Plug 'N Play Systems • Dual Sync Distributors • Ignition Systems • Wiring Harnesses • Intake Manifolds and Accessories • Fuel Injectors • Fuel Pumps and Regulators The first name in ACCELeration! ACCEL/DFI GENERATION 7+ PROGRAMMABLE ENGINE MANAGEMENT SYSTEMS DFI Generation 7+ Programmable Engine Management Systems The new ACCEL/DFI Generation 7+ Engine Management System is the... • BEST EQUIPPED, • MOST CAPABLE, and • EASIEST TO USE system in its class! BEST EQUIPPED Every DFI Generation 7+ Engine Management System comes equipped with multiple software-selectable fuel and ignition con- trol strategies. The following control strategies are available in the module as it comes from the factory: Fueling Strategies • Sequential (Cam signal required) • Staged Sequential (4 Cylinder only, Cam signal required) • Staggered Batch (Bank to Bank) • Throttle Body Injection (Standard,TBI Staged) • Throttle Body Injection (Dual-Quad, Multiple TBI Staged) Ignition Compatibility: • DFI Dual Sync Distributor (supplies both cam and crank signal) • GM High Energy Ignition • LS1 coil on plug ignition • Ford Thick Film Module • Inductive Pick-up Crank Trigger or Distributor type • Hall Effect -- Crank Trigger or Distributor • Buick GN Multiple Coil packs • Ford EDIS • Other Custom, User Defined Settings 202 ACCEL/DFI GENERATION 7+ PROGRAMMABLE ENGINE MANAGEMENT SYSTEMS MOST CAPABLE In addition, each and every DFI Generation 7+ Engine Control Module is capable of controlling a wide
    [Show full text]
  • Basic Ignition Systems Produced By
    Phase 2 Trade of Motor Mechanic Module 4 Unit 1 BASIC IGNITION SYSTEMS Produced by In cooperation with: Subject Matter Experts Martin McMahon & CDX Global Curriculum Revision 2.2 16-01-07 © SOLAS 2013 Module 4 - Unit 1 Basic Ignition Systems Table of Contents Introduction ........................................................................................................ 1 Unit Objective ..................................................................................................... 1 1.0 Health and Safety Procedures ................................................................. 3 1.1 Health and Safety Procedures ...................................................... 3 2.0 Basic Function of the Spark Ignition System ......................................... 5 2.1 Basic Ignition System ................................................................... 5 2.2 Ignition Principles ........................................................................ 5 3.0 Operation of a Contact Breaker Ignition System ................................... 7 3.1 Mechanical Ignition ...................................................................... 7 3.2 The Battery ................................................................................... 9 3.3 Ignition Coil .................................................................................. 9 3.4 Distributors ..................................................................................12 3.5 Ballast Resistor ............................................................................13
    [Show full text]
  • Ignition Systems Application Manual
    Ignition Systems Application Manual Energy and Chassis IGNITION SYSTEMS APPLICATION MANUAL Revised Jan 2005 Ignition Systems Delphi Energy and Chassis Systems Tech Center Brighton 12501 E. Grand River Brighton, Mi., 48114, USA 1999 Delphi Automotive Systems Updated January 2005 Ignition Systems Application Manual Release/Revision Summary Sheet CHANGE DATE REASON FOR CHANGE Originator PAGE(S) NO. Original 30/AUG/99 Released C.R. Strange N/A 1 Jan 2005 Update, pencil coil information added B. Griffith 3-15 – 3-19 Information and graphics added, Ion Sense. Various Ignition Systems Application Manual Table of Contents 1.0 INTRODUCTION..................................................................................................................................1-1 1.1 SCOPE OF DOCUMENT ............................................................................................................................1-1 1.2 CLASSIFICATION .....................................................................................................................................1-1 1.3 DOCUMENT MANAGEMENT ......................................................................................................................1-1 1.3.1 Document Release and Updates .................................................................................................1-1 1.3.2 Mailing List....................................................................................................................................1-2 1.3.3 Document Revision Procedure.....................................................................................................1-2
    [Show full text]
  • Understanding Ignition Systems the Advantages and Disadvantages of Four Common Ignition Systems
    Understanding Ignition Systems The advantages and disadvantages of four common ignition systems While cars have changed drastically throughout the history, there’s one constant that all combustible engines have in common: an ignition system. Currently, we recognize four types of ignition systems used in most cars and trucks: conventional breaker-point ignitions, high energy (electronic) ignitions, distributor-less (waste spark) ignition and coil-on-plug ignitions. In this article, we touch on the features of each system, as well advantages and disadvantages of each. Conventional Breaker-Point Ignition System The conventional breaker-point ignition system is the oldest type of ignition system and has been used since the early days of the automobile, especially through the 1970s. The mechanical nature of these ignition systems, as well as the length of time these systems have been used, they are relatively easy to diagnose and repair. However, they do incorporate a large number of moving parts, increasing the potential for breakdowns. Additionally, deterioration of these systems can negatively affect the maximum spark energy throughout the life of the engine, causing frequent misfires and increasing emissions. High Energy (Electronic) Ignition System After 70-plus years of using conventional breaker-point ignition systems, automotive manufacturers turned to a more advanced, high energy ignition system. This system replaces the breaker points and condenser with a transistorized switch within an ignition module that also handles the task of triggering the ignition coil to generate high-voltage current. This can prove advantageous, as the use of this electronic switch means there are fewer moving parts than in a breaker-point ignition system while still being relatively easy to diagnose and repair.
    [Show full text]