Softspan™ Extremity Expanders Softspan™ Extremity Expanders

ACCESSORIES Catalog No. Description SET01 Softspan Expander Templates, non-sterile, set (request a FREE set) PPL01 Precision Point™ Locator, sterile, each WNIS01 Winged Needle Infusion Set, sterile, set of 5 each RPA01 Remote Port Accessory Set

Order for Doctor:

Patient:

Surgery Date:

Catalog No: Quantity:

Versatile, practical designs

NOMINAL DIMENSIONS The SSP Softspan™ Tissue Expander design reconstructive cases. Designed to address the unique Except as noted, expander dimensions are measured at the concept is the minimization of all critical requirements of large defect reconstruction, the zone minimum suggested fill volume with expander placed on a potential erosion points. To this end, SSP texturing utilizes the assets of both smooth and textured flat surface. Variations may occur, and not every expander will has developed low and flat profile expander surfaces, allowing for ease of expander insertion as well conform exactly to the dimensions given. designs that can be used in the most difficult as secure expander/tissue interface. INTEGRATED INJECTION PORTS ONLY/MAGNETIC STRENGTH of cases while minimizing traditional areas Low initial profile This device contains a strong rare-earth magnet that has been of concern. tested to be detectable through 45mm phantom tissue. This Rounded edges and reduced profiles of all critical magnet is contraindicated in MRI procedures and where the The smooth, rectangular-shaped expander reinforced areas minimize potential erosion points incorporates Dr. Bruce Bauer’s years of clinical Product supplied sterile. Each device supplied magnetic field may affect other polarized devices (e.g., drug infusion devices, pacemakers, artificial sensing devices and experience in dealing with the most difficult Reinforced base facilitates placement and “roll-out” of with a Precision Point™ locator or Remote Port similar type products). expander Accessory Set. Please see package insert for reconstructive expander cases. Rounding of additional product information. LIMITED WARRANTY, LIMITATION OF LIABILITY AND all edges and a remote injection port with the Integrated Precision Point™ magnetic injection port DISCLAIMER OF OTHER WARRANTIES lowest possible point of attachment reduces SSP warrants that reasonable care was used in the manufacture system or remote port options for flexibility in and production of this product. Because SSP has no control over the initial profile of the expander. each case the conditions of use, patient selection, surgical procedure, The curvilinear and angle expanders Smooth, textured, or zone-textured surface options post-surgical stresses, or handling of the device after it leaves encompass Dr. Hugh Vu’s considerable our possession, SSP does not warrant either a good effect or against an ill effect following its use. SSP shall not be responsible experience with pediatric and adult burn for any incidental or consequential loss, damage or expenses directly or indirectly arising from the use of this product. Softspan is a trademarks of Specialty Surgical Products, Inc. This warranty is in lieu of and excludes all other warranties not expressly set forth herein, whether express or implied by operation of law or otherwise, including but not limited to any implied warranties of merchantability or fitness for use.

1123 North US Highway 93 • Victor, MT 59875 • 888.878.0811 • 406.961.0102 • 406.961.0103 FAX

www.ssp-inc.com M093M 08/14 Softspan™ Extremity Expanders

Remote Port Catalog No. Integrated Port Catalog No. Suggested A B C Remote Port Catalog No. Integrated Port Catalog No. Suggested A B C Remote Port Catalog No. Integrated Port Catalog No. Suggested A B C Smooth Shell Textured Shell Smooth Shell Textured Shell Fill Volume (cc) Length (cm) Width (cm) Projection (cm) Smooth Shell Textured Shell Smooth Shell Textured Shell Fill Volume (cc) Length (cm) Width (cm) Projection (cm) Smooth Shell Textured Shell Smooth Shell Textured Shell Fill Volume (cc) Length (cm) Width (cm) Projection (cm) FLAT OVAL† RECTANGLE – Port with approx. 30cm tubing CURVILINEAR† SRE-FO-025S* SRE-FO-025* N/A SIE-FO-65 25 - 62 6.5 5.0 1.5 - 4.0 SHR-LR-020S** N/A N/A N/A 20 - 40 4.0 2.7 2.5 - 3.5 SRE-CV-320S SRE-CV-320 N/A VU-CTE-320 320 - 480 19.0 6.5 3.8 - 6.3 SRE-FO-035S* SRE-FO-035* N/A SIE-FO-76 35 - 89 7.5 6.0 1.5 - 4.3 SHR-LR-030S** N/A N/A N/A 30 - 60 4.1 3.6 3.6 - 4.0 SRE-CV-520S** SRE-CV-520** N/A VU-CTE-520 520 - 780 23.8 7.5 4.5 - 7.0 SRE-FO-060S SRE-FO-060 N/A SIE-FO-86 60 - 150 8.5 6.5 1.5 - 5.2 SHR-LR-070S** N/A N/A N/A 70 - 140 6.0 4.0 3.5 - 5.5 SRE-CV-720S** SRE-CV-720** N/A VU-CTE-720 720 - 1080 26.2 9.0 4.7 - 7.5 SRE-FO-075S SRE-FO-075 N/A N/A 75 - 188 10.0 8.0 1.5 - 5.5 SHR-LR-075S** N/A N/A N/A 75 - 150 8.0 4.0 3.0 - 4.6 CURVILINEAR – Port with approx. 10.25cm tubing FLAT KIDNEY† SHR-LR-100S** N/A N/A N/A 100 - 200 10.0 4.0 3.5 - 5.0 FME-CV-300S** N/A N/A N/A 300 - 480 18.0 6.0 5.0 - 6.3 SRE-FK-025S SRE-FK-025 N/A SIE-FK-74 25 - 62 7.0 4.5 1.5 - 3.5 SHR-LR-160S** N/A N/A N/A 160 - 320 10.0 6.0 3.5 - 6.2 FME-CX-300S** N/A N/A N/A 300 - 480 18.0 6.0 5.0 - 6.3 SRE-FK-080S SRE-FK-080 N/A SIE-FK-106 80 - 200 10.0 6.0 2.0 - 5.5 SHR-LR-250S** N/A N/A N/A 250 - 500 12.0 7.0 3.8 - 7.4 CURVILINEAR – Port with approx. 30cm tubing SRE-FK-140S SRE-FK-140 N/A SIE-FK-127 140 - 350 12.5 7.5 2.5 - 6.5 SHR-LR-340S** N/A N/A N/A 340 - 680 15.0 7.5 3.8 - 8.0 SHR-CV-320S** N/A N/A N/A 320 - 480 19.0 6.5 3.8 - 6.3 SRE-FK-270S SRE-FK-270 N/A N/A 270 - 675 14.0 9.0 4.0 - 8.0 SHR-LR-500S** N/A N/A N/A 500 - 1000 27.5 7.6 2.5 - 6.5 SHR-CV-520S** N/A N/A N/A 520 - 780 23.8 7.5 4.5 - 7.0 LOW RECTANGLE† CRESCENT† SHR-CV-720S** N/A N/A N/A 720 - 1080 26.2 9.0 4.7 - 7.5 N/A N/A SIE-LR-064S SIE-LR-064 60 - 120 6.0 4.0 3.5 - 5.0 SRE-CR-045S SRE-CR-045 SIE-CR-045S SIE-CR-045 45 - 90 8.7 5.5 2.7 - 4.5 SHR-CV-750S** N/A N/A N/A 750 - 1400 29.8 8.0 3.6 - 7.5 SRE-LR-160S SRE-LR-160 SIE-LR-106S SIE-LR-106 160 - 320 10.0 6.0 3.5 - 6.2 SRE-CR-100S SRE-CR-100 SIE-CR-100S SIE-CR-100 100 - 200 10.5 7.4 3.3 - 5.8 ELLIPSOID – Port with approx. 30cm tubing SRE-LR-200S SRE-LR-200 SIE-LR-126S SIE-LR-126 200 - 400 12.0 6.0 3.5 - 6.8 SRE-CR-200S SRE-CR-200 SIE-CR-200S SIE-CR-200 200 - 400 13.7 10.5 4.0 - 7.0 SHR-EL-010S**N/AN/A N/A 10 - 15 3.2 2.4 2.5 - 3.0 SRE-LR-250S SRE-LR-250 SIE-LR-127S SIE-LR-127 250 - 500 12.0 7.0 3.8 - 7.4 SRE-CR-350S** SRE-CR-350** SIE-CR-350S SIE-CR-350 350 - 700 15.0 11.2 5.5 - 8.5 ANGLE SRE-LR-340S SRE-LR-340 SIE-LR-157S SIE-LR-157 340 - 680 15.0 7.5 3.8 - 8.0 ROUND† N/A N/A N/A VU-ATE-200 200 - 300 19.0 4.0 3.5 - 4.5 LOW RECTANGLE – Pull tabs and port with approx. 30cm tubing SRE-RD-220S SRE-RD-220 N/A N/A 220 - 270 9.4 9.4 4.5 - 5.9 N/A N/A N/A VU-ATE-450 450 - 650 23.5 5.0 4.5 - 6.0 SHR-LR-110S** N/A N/A N/A 110 - 220 12.0 4.0 3.2 - 5.4 SRE-RD-270S SRE-RD-270 N/A N/A 270 - 320 10.2 10.2 4.8 - 6.0 WEDGE† SHR-LR-150S** N/A N/A N/A 150 - 300 15.0 4.0 3.3 - 5.4 SRE-RD-320S** SRE-RD-320** N/A N/A 320 - 380 10.8 10.8 5.0 - 6.4 SRE-WG-100S SRE-WG-100 N/A N/A 100 - 120 8.3 5.5 4.5 - 5.5 SHR-LR-200S** N/A N/A N/A 200 - 400 20.0 4.0 3.3 - 5.8 SRE-RD-380S** SRE-RD-380** N/A N/A 380 - 430 11.3 11.3 5.4 - 6.5 SRE-WG-250S SRE-WG-250 N/A N/A 250 - 300 10.5 7.5 6.0 - 7.3 RECTANGLE† SRE-RD-430S** SRE-RD-430** N/A N/A 430 - 500 11.5 11.5 5.6 - 6.9 CALF† BTE070 SPR070 N/A N/A 70 - 90 6.0 4.0 3.5 - 4.6 SRE-RD-500S** SRE-RD-500** N/A N/A 500 - 640 12.2 12.2 6.0 - 8.0 SRE-CC-500S*N/A N/A N/A 500 - 600 19.0 8.0 5.5 - 7.0 SRE-RD-640S** SRE-RD-640** N/A N/A 640 - 750 13.1 13.1 6.7 - 8.2 BTE250 SPR250 N/A N/A 250 - 300 10.0 6.0 5.0 - 6.3 A BTE350 SPR350 N/A N/A 350 - 420 12.0 6.0 5.0 - 7.0 SRE-RD-750S** SRE-RD-750** N/A N/A 750 - 860 14.0 14.0 6.9 - 8.5 A B BTE500** SPR500** N/A N/A 500 - 600 12.0 7.0 6.0 - 7.8 SRE-RD-860S** SRE-RD-860** N/A N/A 860 - 1020 14.5 14.5 7.7 - 9.0 15˚5˚ B BTE750** SPR750** N/A N/A 750 - 900 15.0 7.5 7.0 - 9.0 C A B BTE1000** SPR1000** N/A N/A 1000 - 1200 17.0 8.0 8.0 - 10.2 A ANGLE BTE1200** N/A N/A N/A 1200 - 1400 20.0 8.5 8.5 - 10.4 A A A B C CURVILINEAR C B A A A B CURVILINEAR (FME-CX) WEDGEGE C A B B B C C A C B RECTANGLE CRESCENT ROUND B C A B C C C FLAT OVAL FLAT KIDNEY LOW RECTANGLE C CALFCALF

* No reinforced base on this size. C ** LARGE remote port. All others are STANDARD. † Remote port has approx. 17cm tubing. CURVILINEAR (FME-CV) ELLIPSOID