OPEL Antara
Operation, Safety, Maintenance 2
Data specific to your vehicle Please enter your vehicle’s data here to keep it easily accessible. This information is available under the section "Technical data" as well as on the identification plate. Fuel Designation
Engine oil Grade
Viscosity
Tyre pressure Tyre size for load of up to 4 persons for full load Summer tyres Front Rear Front Rear
Winter tyres Front Rear Front Rear
Weights Permissible Gross Vehicle Weight
– EC kerb weight
=Loading 3
Your Antara Make use of the Owner's Manual: This symbol signifies: is an intelligent combination of forward- z Its "In brief" section will give you an initial 6 Continue reading on next page. looking technology, impressive safety, overview. 3 The asterisk signifies equipment not environmental friendliness and economy. z The table of contents at the beginning of fitted to all vehicles (model variants, It now lies with you to drive your vehicle the Owner’s Manual and within the engine options, models specific to one safely and ensure that it performs individual chapters will show you where country, optional equipment, Opel perfectly. This Owner's Manual provides everything is. genuine parts and accessories). you with all the necessary information to z Its index will help you find what you 9 Warning that end. want. Make sure your passengers are aware of z It will familiarise you with the Text marked 9 Warning provides the possible risk of accident and injury sophisticated technology. information on risk of accident or injury. which may result from improper use of the Disregard of the instructions may lead to z vehicle. It will increase your pleasure in your injuries or endanger life. vehicle. You must always comply with the specific Inform your passengers accordingly. laws of the country that you are travelling z It will help you to handle your vehicle through. These laws may differ from the expertly. information in this Owner’s Manual. Yellow arrows in the illustrations serve as The Owner’s Manual is designed to be points of reference or indicate some action When instructed to consult a workshop, clearly laid-out and easily understood. to be performed. we recommend that you consult an Opel Partner. Black arrows in the illustrations indicate a reaction or a second action to be All Opel Partners offer first-class service at performed. reasonable prices. Directional data, e.g. left or right, or front You will receive quick, reliable and or back, in the descriptions always relates individual service. to the direction of travel. Experienced mechanics, trained by Opel, We wish you many hours of pleasurable work according to specific Opel driving instructions. Your Opel Team The Owner's Manual should always be kept together with the Service and Warranty Booklet in the vehicle: Ready to hand in the glove compartment. 4 5
Handling characteristics In brief ...... 6 Contents All Wheel Drive vehicles have a high centre Locks, doors, windows ...... 21 of gravity due to the increased ground Seats, interior ...... 36 clearance required for off-road use. Instruments, controls ...... 70 As with other vehicles of this type, failure to Lighting ...... 94 operate the vehicle correctly may result in Infotainment system ...... 101 loss of control or an accident. Climate control ...... 103 Please read the sections "All Wheel Drive" Driving and operation ...... 115 on page 121 and "Driving hints" on Self-help, vehicle care ...... 171 page 127. Service, maintenance ...... 206 Technical data ...... 215 Index ...... 228 6 In brief In brief
To unlock and open the vehicle: To unlock and open the tailgate: Press button q, pull door handle Press button q on remote control, 6 Door locks - see pages 30, 72, operate button above keys - see page 21, license plate electronic immobiliser - see page 22, 6 Tailgate - see page 26, radio frequency remote control - radio frequency remote control - see page 23, see page 23, central locking system - see page 25, central locking system - see page 25, anti-theft locking system - see page 27, anti-theft alarm system - see page 27. anti-theft alarm system - see page 27. In brief 7
Front seat adjustment: Adjusting front seat backrests: Adjusting the lumbar support 3: Pull handle, slide seat, Lift release lever on outboard side Turn handwheel release handle of seat Adjust lumbar support to suit personal 6 Seats - see page 36, Move seat backrest to suit seating position. requirements. seat position - see page 38. Do not lean on seat backrest whilst adjusting it. 6 Seats - see page 36, seat position - see page 38. 8 In brief
Adjusting seat height 3: Adjusting head restraint height: Fitting seat belt: Raise or lower lever on outboard Press release button, Draw seat belt smoothly from side of seat adjust height, then release inertia reel, guide over shoulder Lever pumping action 6 Head restraints - see page 39, and engage in buckle upward: raises seat head restraint position – see page 39. The belt must not be twisted at any point. downward: lowers seat The lap belt must lie snugly against the body. 6 Seats - see page 36, The backrests must not be tilted back too seat position – see page 38. far (recommended maximum tilting angle approx. 25°). To release belt, press red button on belt buckle. 6 Seat belts – see pages 43 to 47, airbag systems – see page 52, seat position – see page 38. In brief 9
To adjust interior mirror: Electrically adjustable exterior Fold in exterior mirrors: Swivel mirror housing mirrors: Manually: press lightly. Swivel lever on underside of mirror housing Four way switch in driver’s door Electrically 3: with ignition switch in to reduce dazzle at night. Move selector switch to L or R; four way positions ACC or ON, press button n and Take care when driving with interior mirror switch adjusts corresponding mirror. both mirrors will fold in. adjusted for night vision. Rear view may be 6 Further information, Press button n again; both mirrors will fold slightly distorted in this position. automatic anti-dazzle exterior mirrors - to the driving position. 6 Mirrors - see page 31, see page 31, heated exterior mirrors - see page 105. If a folded-in electric mirror has been automatic anti-dazzle interior mirror - folded out manually, pressing button n see page 32. only folds the other mirror out. Pressing button n again folds both mirrors back in. Fold mirrors back into driving position before driving the vehicle. 10 In brief In brief 11
Page Page Page 1 Side air vents ...... 104 9 Centre air vents...... 104 17 Accelerator pedal...... 127 2 Door window defroster vents...... 104 10 Hazard warning...... 14 18 Driver’s airbag ...... 52 3 3 Headlamp flash and main beam .... 14 Park pilot ...... 142 19 Brake pedal...... 127, 146 Descent Control System (DCS)...... 138 turn signal lamps ...... 14 20 Clutch pedal 3...... 127, 128 Peripheral lighting...... 98 Electronic Stability Control (ESC) ... 136 cruise control 3 ...... 140 Front passenger’s 21 Steering wheel adjustment ...... 13 seat belt reminder 3...... 46 4 Infotainment system Fold in exterior mirrors 3 ...... 30 22 Bonnet release ...... 171 remote control buttons...... 101 Control indicator for 23 Coin storage...... 67 Trip computer 3...... 81, 88 anti-theft alarm system 3...... 29 24 Card holder ...... 67 5 Horn ...... 15 11 Infotainment system...... 101 25 Parking lamps...... 94 6 Instruments...... 70 12 Front passenger’s airbag...... 52 dipped beam ...... 14, 95 7 Windscreen and tailgate 13 Glove compartment...... 64, 105 automatic dipped beam wipers and washers ...... 15, 16 activation 3 ...... 95 headlamp washers 3...... 16 14 Fuse box ...... 182 headlamp range adjustment 3...... 97 15 Climate control...... 103 front fog lamps...... 96 8 Central information display for time, fog tail lamp ...... 96 date, outside temperature, 16 Ignition switch ...... 13 instrument illumination ...... 98 Infotainment system, check control 3 ...... 91 Trip computer 3...... 81, 88 12 In brief
Control indicators o Electronic immobiliser: N Water in diesel fuel filter 3: see pages 22, 72. see pages 73, 194. ABS (Anti-lock Brake System): u 3 see page 148. 9 Door open: C Change engine oil : see page 72. see page 73. Trailer indicator 3: g 3 see page 70. 3 Engine electronics, N Preheating for diesel engines : transmission electronics 3: see pages 19, 73. Brake system: 4 see pages 72, 134. 3 see pages 70, 145. I DPF (Diesel particle filter) : v Airbag systems 3, see pages 73, 135. Park pilot 3: r belt tensioners: 3 see pages 71, 142. m Cruise control : see pages 44, 52. see page 140. DCS (Descent Control System): 5 1 Tailgate open: 3 see pages 71, 138. S Engine oil level : see page 72. see page 73. B AWD (All Wheel Drive): X Driver’s seat belt reminder: see pages 71, 121. 2 Power steering: see page 72. see page 73. 7 ESC Active & Warning O Turn signal lamps: a Anti-theft alarm system activation (Electronic Stability Control): see pages 14, 72, 95. see page 136. without monitoring of passenger Y Low fuel level: compartment and vehicle tilt 3: A ESC Not Ready: see pages 72, 76, 132, 225. see page 28. see page 136. > Front fog lamps: I Engine oil pressure: J ESC OFF: see pages 73, 96. see page 74. see page 136. r Fog tail lamp: p Alternator: q Automatic headlamp range see pages 73, 96. see page 74. adjustment 3: see pages 71, 97. P Headlamp main beam: Z Exhaust emissions: see pages 14, 73, 95. see pages 74, 134. W Coolant temperature: see pages 71, 195. G Low windscreen washer fluid: 0 Winter program: see page 73. see pages 74, 117. In brief 13
Steering column lock and ignition: Steering wheel adjustment: Exterior lamps Turn key to position ACC. Move lever down, Turn light switch: To release lock, adjust height and distance, J =Off rotate steering wheel slightly move lever up and engage 8 =Parking lamps Positions: Adjust steering wheel only with vehicle 9 = Dipped beam or LOCK = Ignition off stationary and steering column lock released. main beam ACC = Steering unlocked, ignition off AUTO = Automatic dipped Push the lever firmly upwards to ensure ON = Ignition on, with diesel engine: beam activation 3 preheating that the steering wheel is locked in position. START = Start (transmission in neutral) 6 Airbag systems - see page 52. Press button: 6 Starting - see page 19, > =Front fog lamps electronic immobiliser - see page 22, r = Fog tail lamp parking the vehicle - see page 20. 6 Headlamp warning device - see page 92, further information - see page 94, headlamp range adjustment 3 - see page 97, headlamps when driving abroad - see page 100, daytime running lamps 3 - see page 94. 14 In brief
Headlamp flash, main and Turn signal lamps: Hazard warning lamps: dipped beam: Lever in rest position On = Press ¨ Headlamp = Pull lever Upwards = Right turn Off = Press ¨ again flash towards Downwards = Left turn 6 Hazard warning lamps - see page 97. steering wheel 6 Turn signal lamps - see page 95. Main beam = Push lever forwards Dipped beam = Pull lever back towards steering wheel 6 Main beam, headlamp flash - see page 95. In brief 15
Activate horn j: Windscreen wipers: Automatic wiping with rain Press either side of the Move lever upwards sensor 3: steering wheel J =Off Move lever to automatic wiping The horn will sound regardless of ignition $ =Timed interval wipe with rain sensor position $ switch position. % =Slow The rain sensor detects the amount of 6 Airbag systems - see page 52, & =Fast water on the windscreen and automatically remote control on steering wheel - regulates the windscreen wipers. Press lever down from position J: see page 101. 6 Single swipe. Windscreen wipers - see page 92, further information - see pages 198, 202, 6 Windscreen wipers - see page 92, 205. adjustable wiper interval - see page 92, further information - see pages 198, 202, 205. 16 In brief
Operating windscreen and Tailgate wiper and washer Heated rear window, headlamp washer systems 3: systems: heated exterior mirrors 3: Pull lever towards steering wheel Wipers on = Push lever forward Press Ü =On 6 Windscreen and headlamp washer Wipers off = Pull lever back Press Ü again = Off systems - see page 93, towards steering 6 Air conditioning - see page 109, further information - see pages 199, 202, wheel heated rear window, heated exterior 205. Wash = Press and hold mirrors - see page 105. button 6 Tailgate wiper and washer systems - see page 93, further information - see pages 198, 199, 202, 205. In brief 17
Drying misted up or iced up To set automatic mode of Manual transmission: windows: Electronic Climate Control 3: 1 to 5 = 1st to 5th gear Set air distribution to position l, Press AUTO button, R = Reverse gear set the temperature rotary knob set temperature using Only engage reverse gear when the vehicle to red and fan to position 4, rotary knob is stationary. switch on heated rear window Ü Open all air vents. Close centre air vents, open side air vents 6 Electronic Climate Control (ECC) - and direct them towards the door windows. see page 111. 6 Heating, ventilation and air conditioning system - see pages 106, 109. 18 In brief
Before starting-off, check: z Tyre pressures and condition. z Engine oil level and fluid levels in engine compartment (see page 192). z All windows, mirrors, exterior lighting and license plates are free from dirt, snow and ice and are operational. z Objects are securely located and will not be thrown forward in the event of sudden braking. z Seats, seat belts and mirrors are correctly adjusted. Automatic transmission 3: Manual mode: z All gauges and control indicators. P=Park position < = Shift to higher gear z Brake operation. R = Reverse ] =Shift to lower gear N = Neutral (idle) 6 Further information - see page 117. D = Automatic gear selection Starting is only possible in P or N. To move from P or N, switch on ignition, depress foot brake and press selector lever button. Engage P or R: press selector lever button. P: Only with vehicle stationary, first apply hand brake R: Only with vehicle stationary. 6 Automatic transmission - see page 115. In brief 19
Start attempts should not last longer than 15 seconds. If engine does not start, wait 10 seconds before repeating starting procedure. The increased engine speed automatically returns to normal idling speed as the engine temperature rises. Drive at a moderate speed, especially in cold weather, until normal engine operating temperatures have been reached. 6 Electronic immobiliser - see page 22, diesel fuel system - see page 171, Starting the engine: further information - see pages 127, 129, Releasing the hand brake: 131. Manual transmission in neutral, Raise lever slightly, Depress clutch and foot brake, press release button, Automatic transmission in P or N, lower lever fully Do not accelerate To reduce operating forces, depress foot brake at the same time. Petrol engines: Do not drive with hand brake on, to avoid TurnkeytoSTARTand release it damage to brakes on the rear wheels. Do Diesel engines: not apply hand brake while vehicle is in Turn key to ON, when preheating motion or as a substitute for the foot brake. control indicator N Drive carefully, economically and with the extinguishes1), turn key to START environment in mind. While driving, do not and release it do anything that could distract you. Key returns automatically to ON position 6 Hand brake - see page 147. when released.
1) Preheating system switches on only if outside temperature is low. 20 In brief
Advice when parking: That was the most important z Always apply hand brake firmly and as information for your first drive in firmly as possible on slopes. your Antara in brief. z Push key into ignition switch before removing (vehicles with automatic transmission 3: depress foot brake and shift into P before removing key). Turn steering wheel until lock is felt to engage Your vehicle has still more (anti-theft protection). instruments and controls, z If the vehicle is parked on a level surface possibly also optional equipment. or a hill, select 1st gear before switching ignition off (vehicles with automatic transmission 3: move selector lever to P). Also turn front wheels away from kerb if Parking the vehicle: parked on an uphill slope. Apply hand brake firmly, The remaining chapters of the close windows, If the vehicle is parked on a downhill Owner’s Manual contain switch off engine, remove key, slope, select reverse gear before important information on switching ignition off (vehicles with operation, safety and engage steering column lock, automatic transmission 3: move selector lock vehicle lever to P). Also turn front wheels maintenance as well as a 6 Further information - see pages 22, 128, towards kerb. complete index. radio frequency remote control - z see page 23, Switch off exterior lamps, otherwise the central locking system - see page 25, headlamp warning device will sound anti-theft alarm system - see page 27. when the driver’s door is opened. z Cooling fans may run on after the engine has been switched off. z Do not park on easily ignitable surfaces as hot exhaust system temperatures could cause the surface to ignite. Locks, doors, windows 21
Locks, doors, windows Replacement keys The key is a constituent of the electronic immobiliser. In case of loss, replacement keys can be ordered from your Opel Partner by quoting the key number and Vehicle Identification Number (VIN). Replacement keys ...... 21 Once a new transmitter is coded, the lost Car Pass...... 21 transmitter will not unlock your vehicle. 3 Key with foldaway key section ...... 21 Ordering keys from an Opel Partner Electronic immobiliser...... 22 guarantees problem-free operation of the Radio frequency remote control ...... 23 electronic immobiliser. Central locking system ...... 25 Keep spare key in a safe place. Tailgate ...... 26 Locks - see page 205. Mechanical anti-theft locking Key with foldaway key section 3 system 3 ...... 27 Car Pass Press button to extend. Press button to Anti-theft alarm system 3 ...... 27 The Car Pass contains all of the vehicle’s retract; key section audibly engages. Child safety locks...... 30 data and should therefore not be kept in Exterior mirrors...... 30 the vehicle. Interior mirror ...... 31 Have your Car Pass on hand when Electric windows...... 32 consulting an Opel Partner. Sun visors...... 34 Slide/tilt sun roof 3 ...... 34 22 Locks, doors, windows
Note The immobiliser does not lock the doors. Therefore, after leaving the vehicle, always lock it and switch on the anti-theft alarm system 3 - see pages 25, 27.
Electronic immobiliser Control indicator o for immobiliser The system checks whether the vehicle may The control indicator illuminates when the be started using the key that has been ignition is switched on, then extinguishes. inserted. If the key is recognised as If the control indicator stays illuminated "authorised", the vehicle can be started. after the ignition is switched on, there is a The check is carried out via a transponder fault in the immobiliser system. housed in the key. z Turn key to LOCK position and remove, The electronic immobiliser is automatically z wait approximately two seconds, activated when the key is turned to LOCK z then repeat starting procedure. position and removed from the ignition If the control indicator fails to extinguish, switch. try to start the engine using the spare key and seek the assistance of a workshop. Locks, doors, windows 23
Treat the remote control unit with care: Central locking system it should be protected against moisture, see page 25. kept out of direct sunlight and should not Mechanical anti-theft locking system 3 be operated unnecessarily. see page 27. Do not place heavy objects on the remote Anti-theft alarm system 3 control unit, and avoid dropping it. see page 27. The hazard warning lamps come on to indicate that the remote control is operational.
Radio frequency remote control The remote control is used to operate: z Central locking system, z Mechanical anti-theft locking system 3, z Anti-theft alarm system 3. The remote control has a range of approx. 6 metres. The range may be reduced due to environmental conditions or shadowing and reflection of the radio waves. To operate the remote control, direct the remote control unit at the vehicle. 24 Locks, doors, windows
Fault Key with fixed key section: If the central locking system cannot be insert a small screwdriver in the notch on operated with the remote control, this may the cover and prise it open. be due to the following reasons: Remove used battery, taking care to avoid z The remote control is out of range. touching the circuit board to other z The battery voltage of the remote components. control is too low. Change the battery in Ensure the new battery is installed correctly the remote control unit. with positive (+) side facing down towards z The remote control has been repeatedly the base. operated outside the vehicle’s reception Close cover, ensuring it audibly engages in range (e.g. at too great a distance from the key part. the vehicle). The remote control must be reprogrammed. We recommend you 9 Warning consult your Opel Partner. Changing battery in remote control unit Used lithium batteries can harm the z The system has been overloaded as a Replace the battery in accordance with the environment. Make sure that you dispose result of repeated operation at short information on pages 206 to 212 or when of old batteries in accordance with intervals. The power supply is cut-off for the range of the remote control starts to environmental protection regulations. a brief period. become reduced. Do not dispose with household refuse. z Interference from higher power radio Key with foldaway key section: waves from other sources. open cover by hand. Lock or unlock the doors manually using Remove used battery, taking care to avoid the key or central locking switch - touching the circuit board to other see page 25. components. Have cause of fault remedied by a Ensure the new battery is installed correctly workshop. with positive (+) side facing up. Close cover, ensuring it audibly engages in the key part. Locks, doors, windows 25
To unlock: Press button q on remote control - or - Press central locking switch m in driver’s door. If no door is opened within approx. 30 seconds after the vehicle has been unlocked via the remote control, the vehicle is relocked automatically and anti-theft alarm 3 is reactivated. When button q is pressed, the instrument panel illuminates for approx. 30 seconds or until ignition switch is turned to the ACC position. Central locking system Central locking switch m For front doors, rear doors, tailgate and 9 Warning Use the central locking switch to lock or tank flap. unlock the doors, tailgate and tank flap For safety reasons, the vehicle cannot be from inside the vehicle. To lock: locked or unlocked via the remote control Press button p on remote control Press the right part of the switch to lock or (and the anti-theft system 3 will not be - or - the left part of the switch to unlock. activated) if the key is in the ignition With the doors closed, press central locking switch. switch m in driver’s door. The central locking system can be activated with the windows open. Always ensure that the doors, bonnet, tailgate, sun roof 3 and windows are properly closed and that there are no passengers left in the vehicle before locking with the remote control. 26 Locks, doors, windows
9 Warning
Ensure there are no obstructions and that there is adequate clearance when opening the tailgate. Do not drive with tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases could penetrate the vehicle interior. If driving with tailgate open is necessary, set fan to highest speed, open all air vents, close windows and ensure air recirculation mode is off, to allow entry of Tailgate outside air. To close and lock To unlock and open There is a handle on the inside of the Press button q on remote control tailgate for closing the luggage - or - compartment. Press central locking switch m in driver’s Close tailgate by pushing it down so it door. latches securely. Ensure tailgate is fully The tailgate is unlocked together with the closed before driving. doors and can be opened by operating the To lock tailgate, together with the doors: button above the license plate and lifting Press button p on remote control the tailgate. - or - With the engine running, the tailgate will Press central locking switch m in driver’s only unlock when the hand brake is applied door. or automatic transmission 3 is in P. If the ignition is switched on, the tailgate If the tailgate is open when the ignition is open control indicator 1 extinguishes in switched on, tailgate open control the instrument panel. indicator 1 illuminates in the instrument panel. Locks, doors, windows 27
Mechanical anti-theft locking To unlock: Anti-theft alarm system 3 system 3 Press button q on remote control The system monitors: - or - 9 Warning Turn key in driver's door lock towards front z Front and rear doors. of vehicle, then turn it back to the vertical z Tailgate, bonnet. Do not use the system if there are people position and remove. z Ignition switch. in the vehicle. The doors cannot be unlocked from inside. 9 Warning z Passenger compartment 3. z Vehicle tilt, e.g. if it is raised 3. Unlocking is not possible in any other To lock: way, so keep spare key in a safe place. z Siren power supply 3. All doors and the tailgate must be closed; press button p on remote control again within 3 seconds after locking - or - Turn key in driver's door lock towards rear of vehicle again within 3 seconds after locking, then turn it back to the vertical position and remove. Lock buttons on all doors are positioned such that doors cannot be opened. 28 Locks, doors, windows
9 Warning
Do not use the system if there are passengers in the vehicle. The doors cannot be unlocked from the inside when the alarm is activated.
The remote control unit is used to operate the anti-theft alarm system.
To activate Always ensure that the doors, bonnet, tailgate, sun roof 3 and windows are properly closed and that there are no Confirm that the control indicator starts Activation without monitoring of passengers left in the vehicle before flashing slowly, after illuminating for passenger compartment and vehicle tilt 3 activating anti-theft alarm system. approx. 30 seconds, to show that the anti- Switch on when, for example, animals are Press button p on remote control theft system has been activated. to be left in the vehicle. - or - If button p is pressed again, the anti-theft 1. Close tailgate and bonnet. Lock driver’s door by turning key in door alarm system will activate automatically, 2. Press button a in the roof lining. lock towards rear of vehicle then turn it bypassing the 30 second delay. Control indicator a illuminates in back to the vertical position and remove; If the hazard warning lamps do not flash yellow in the instrument panel. z Hazard warning lamps flash once, on activation or the control indicator 3. Close doors. z All doors are locked, flashes quickly, this may indicate that a 4. Switch on anti-theft alarm system. z Anti-theft system is activated after door, the tailgate or the bonnet is not fully Control indicator for anti-theft alarm approx. 30 seconds. closed. system illuminates. After a 30 second delay, the system is activated without monitoring of the passenger compartment or vehicle tilt. Control indicator a remains illuminated in the instrument panel until the system is switched off by pressing button a again. Locks, doors, windows 29
To deactivate Alarm Press button q on remote control While the alarm system is switched on, the - or - alarm can be triggered, indicated by: Unlock driver’s door by turning key in door z an acoustic signal (horn) and lock towards front of vehicle, then turn it back to the vertical position and remove: z a visual signal (exterior lamps). z Hazard warning lamps flash twice, The number and duration of the alarms are z All doors are unlocked, legally established. z Anti-theft system is deactivated. The alarm is stopped by pressing q or p If the driver’s door is not opened, or the on the remote control or by unlocking engine is not started within 30 seconds of the driver’s door with the correct key. deactivation, all doors are automatically The anti-theft alarm system is deactivated relocked and the system is reactivated. at the same time. Control indicator for anti-theft alarm If the alarm has been triggered, the hazard system 3 warning lamps will not flash upon The control indicator illuminates to show deactivation. that the system is operational when the Note doors are locked with the remote control or The anti-theft alarm system cannot be the key. When the doors are unlocked with deactivated in any other way, so keep a the key or remote control, the control spare key in a safe place. indicator extinguishes. Changes to the vehicle interior, such as the use of seat covers, could impair the function of passenger compartment monitoring 3. 30 Locks, doors, windows
Child safety locks Exterior mirrors Fold in exterior mirrors Electrically adjustable exterior mirrors Manually: the exterior mirrors can be 9 Warning Adjust with the four way switch in driver’s folded in by pressing lightly on the outside door: move selector switch to L or R; of the mirror housing. Use the child safety locks whenever four way switch adjusts corresponding Electrically 3: with ignition switch in children are occupying the rear seats. mirror. positions ACC or ON, press button n and Disregard may lead to injuries or both mirrors will fold in. endanger life. Vehicle passengers must The mirror glass swivels in the same be informed accordingly. direction as the activation of the four way Press button n again; both mirrors will fold switch. to the driving position. 3 To engage lock, open door, insert key into Heated exterior mirrors - see page 105. If a folded-in electric mirror has been child safety lock and turn lock from the folded out manually, pressing button n vertical to the horizontal position. Door only folds the other mirror out. Pressing cannot then be opened from inside. button n again folds both mirrors back in. To unlock door while child safety lock is Fold mirrors back into driving position activated, pull up lock button and open before driving the vehicle. door from outside. Do not pull inside door handle while child safety lock is activated. Locks, doors, windows 31
For the safety of pedestrians, the exterior Automatic anti-dazzle exterior mirrors 3 Interior mirror mirrors will swing out of their normal Dazzle is automatically reduced. To adjust interior mirror, swivel mirror mounting position in the event of an Exterior mirrors dim to reduce glare housing. accident-like impact. automatically in conjunction with the Swivel lever on underside of mirror housing As exterior mirrors are convex, objects are automatic anti-dazzle interior mirror 3 - to reduce dazzle at night. closer than they appear. Use interior mirror see page 32, Fig. S13260. to judge size and distance of objects. Take care when driving with interior mirror adjusted for night vision. Rear view may be Do not scrape ice from exterior mirrors or slightly distorted in this position. force them if frozen. Use a de-icer. 32 Locks, doors, windows
Electric windows 9 Warning
Care must be taken when operating the electrically operated door windows. There is a risk of injury, particularly for children, and a danger that articles could become trapped. Vehicle passengers must be informed accordingly. If there are children on the rear seats, press the switch in the driver’s door to lock rear window operation. Rear windows can then only be operated via Automatic anti-dazzle interior mirror 3 the driver’s door switches. Operational with key in ignition switch Dazzle is automatically reduced. Keep a close watch on the windows when positions ACC or ON. If key is in LOCK With the ignition off, the mirror does not closing them. Ensure that nothing position or removed, windows can be dim. becomes trapped in them as they move. operated for 10 minutes or until driver’s door is opened. Press button on mirror housing to turn Before leaving the vehicle, remove the function on. Button will illuminate. ignition key in order to prevent Operated via four switches located in the Press button again to turn off. unauthorized operation. driver’s door. There are two light sensors in the mirror For incremental operation, briefly pull or housing. To avoid interference and loss of press the switch. function, do not cover the sensors or hang For automatic 3 opening or closing, pull or anything on the mirror. press the switch longer. Pull or press the switch again to stop the movement. Locks, doors, windows 33
Safety function 3 If the window glass encounters resistance above the middle of the window during automatic closing, it will stop immediately and will be opened again. In the event of difficulty due to frost or the like, press the relevant window switch several times until the window is closed.
Additional switches are located in the front Child safety system for rear windows passenger’s door and the rear doors. Press z switch in driver’s door to lock rear The rear windows do not open fully. window operation. With the lock on, rear passenger windows can only be operated via the switches in the driver’s door. 34 Locks, doors, windows
To open Press switch rearwards; it will open automatically unless the switch is pressed again in another direction, or released.
To close Press and hold switch forwards. Release switch when sun roof reaches desired position.
To tilt Press and hold switch upwards. Release switch when sun roof reaches desired position. 3 To return sun roof to its original position, Sun visors Slide/tilt sun roof press and hold switch downwards. Release Use the sun visor to protect from glare by Operated via switch in roof lining when the switch when sun roof reaches desired pulling it up, down or swivelling it to the ignition switch is in positions ACC or ON. position. side. With key in LOCK position in the ignition Sun visors have vanity mirrors and a ticket switch or removed, the slide/tilt sun roof holder 3 on the rear. can be adjusted for up to 10 minutes or When the vanity mirror covers are opened, until a door is opened. the sun visor lamp 3 will illuminate. For incremental operation, briefly press the button. For automatic opening or closing, press and hold the switch. Locks, doors, windows 35
Note z If the top of the sun roof is wet, tilt it to allow water to run off before opening the sun roof. z When carrying a roof load, check the clearance of the sun roof, to avoid damage. 9 Warning
Care must be taken when operating the sun roof. Do not place any objects or body parts in the sun roof opening. Keep sun roof clear of debris. Do not place heavy objects on or around sun roof. When leaving the vehicle unattended, ensure the sun roof is fully closed. 36 Seats, interior Seats, interior
Front seats ...... 36 Rear seats...... 41 Seat belts...... 42 Child restraint systems 3 ...... 47 Airbag systems ...... 52 Storage ...... 59 Drink holders ...... 67 Ashtrays 3...... 67 Front seats Adjusting front seat backrests Warning triangle ¨ 3, To adjust, lift the release lever, move seat First aid kit +3...... 68 9 Warning backrest to suit seating position and lock in position when the lever is released. Power outlets ...... 68 Never adjust seats whilst driving as they Do not lean on the seat backrest whilst Assist grips ...... 69 could move uncontrollably. adjusting it.
Adjust seat longitudinally To adjust, pull the handle on the front seat, slide the seat and release the handle. Seats, interior 37
Electrically adjustable front seat 3 9 Warning
Care must be taken when operating electrically adjustable seats. There is a risk of injury, particularly for children and a danger that articles could become trapped. Keep a close watch on the seats when adjusting them. Vehicle passengers must be informed accordingly.
Adjusting the lumbar support 3 Adjusting seat height 3 To adjust, turn the handwheel whilst To adjust, operate lever on side of seat. relieving the load on the backrest. Lever pumping action Adjust lumbar support to suit personal upward: raises seat requirements. downward: lowers seat 38 Seats, interior
Seat position Adjust driver’s seat such that, with the driver sitting upright, the steering wheel is held in the area of its upper spokes with the driver’s arms slightly bent. Slide front passenger’s seat as far back as it will go. The seat backrests must not be tilted back too far (recommended maximum tilting angle approx. 25°). 9 Warning
Disregard can lead to injuries which could Adjustment Seat backrest adjustment: be fatal. Vehicle passengers must be The seat position can be adjusted by Move upper part of rear switch forwards/ informed accordingly. means of switches on the outboard side of backwards. the seat. Operate switch until desired seat position is Adjusting the longitudinal position: reached. Seat position - see next column. Move front switch forwards/backwards. After adjusting the seat, adjust height of Height adjustment: seat belt - see page 47. To adjust height of front part of seat The seat backrest must not be tilted back cushion, push front part of switch up/down. too far (recommended maximum tilting To adjust height of rear part of seat angle approx. 25°). cushion, push rear part of switch up/down. To adjust height of entire seat cushion, push both front and rear parts of switch up/down. Seats, interior 39
Active head restraints 3 In the event of a rear-end impact, the active head restraints automatically tilt forwards. The head is more effectively supported by the head restraint and the danger of hyperextension in the area of the cervical vertebra is reduced. Do not attach objects or components that are not approved for your vehicle to the head restraints. These affect the protective effect of the head restraints and can be propelled through the vehicle in an uncontrolled manner if the driver brakes hard or an accident occurs. Head restraints Head restraint position To adjust head restraint height, press For maximum protection, the middle of the release button, adjust height to suit then head restraint should be at eye level. If this release the button. is not possible for extremely tall persons, Pull head restraint up to raise. Push head set to highest position, and set to lowest restraint down while pressing the release position for extremely small persons. button to lower the head restraint. 9 Warning
Disregard can lead to injuries which could be fatal. Vehicle passengers must be informed accordingly before moving away. 40 Seats, interior
Removing the head restraints Insert a suitable tool into the small hole in the side of the guide sleeve without the release button and depress the lock. Press the release button on the other guide sleeve and pull up the head restraint. Stow head restraints securely in luggage compartment.
Front seat armrest 3 Folding down the passenger’s seat 3 The armrest can be slid forwards. Pull up Push front passenger’s seat head restraint and hold upper lever and slide the armrest all the way down - see page 39. forwards. Slide front passenger’s seat as far back as To return armrest to its rearmost position, it will go. slide it back until it latches into position. Fold seat forwards by lifting backrest Console box in front armrest - see page 65. release lever and folding backrest down onto seat cushion. Seats, interior 41
To raise the seat, lift backrest release lever and push backrest to upright position. Push and pull on seat backrest to ensure it is locked, thus avoiding excessive forward movement in the event of a collision. 9 Warning
If longer objects, e.g. skis, are to be carried on the back of the front passenger’s seat backrest, ensure they are not in the area in which the front passenger’s airbag inflates or in the area between the seat backrest and the vehicle body. In the event of a collision, Rear seats Folding rear seat backrests such objects may be thrown through the To adjust backrests, lift release lever The luggage compartment can be vehicle. located on top of backrest and move enlarged by folding the rear seat backrests The load must not hinder hand brake backrest forwards or backwards to desired onto the seat cushions. operation or gearshifting. position. To fold rear seat backrests separately, Disregard of these notes can lead to Do not lean on seat backrest whilst unbuckle all three rear seat belts and injuries which may be fatal. adjusting it or make adjustments while the ensure front seats are not in reclined vehicle is moving. position. When folding the rear seat backrests, Push head restraints all the way down, lift ensure the seat belts are unbuckled. backrest release lever and fold backrest forwards and down onto seat cushion. Do not allow passengers to sit on folded backrest, or place any unrestrained loads on it. 42 Seats, interior
Seat belts 9 Warning Three-stage restraint system The system comprises: When folding the backrest, use caution - beware of moving parts. z Three-point seat belts. z Belt tensioners, with load limiters, on the Safety net 3 - see page 60. front seats. z Airbag systems for driver, front Restoring rear seat backrests passenger and rear outboard seat Lift and push backrest up and backwards occupants. to restore it to its original position. Ensure backrest latches into place by pushing top The three stages are activated in sequence of backrest and pulling it forwards again. depending on the seriousness of the accident: 9 Warning Rear seat armrest 3 z The automatic seat belt locking devices The armrest can be folded down. prevent the belt strap from being pulled Ensure that the backrest returns to its out and thus ensure that the vehicle correct position - see page 38. If the rear centre seat is being used or the occupants are retained in their seats. rear seat backrests are being folded down, Never adjust the rear seat backrests fold armrest upwards. z The front seat belt buckles are pulled whilst the vehicle is moving. They could downwards. As a result, the seat belts move in an uncontrolled manner when Console box in rear armrest - see page 65. are instantaneously tightened and the the lever has been pulled. occupants are made aware of the deceleration of the vehicle at a very early stage. This reduces stress placed on the body. Seats, interior 43 z The airbag system is additionally Three-point seat belts In the event of an accident, persons not triggered in the event of a serious The front and rear seats are equipped with wearing seat belts endanger their fellow accident involving a frontal impact, and three-point seat belts with automatic occupants and themselves. forms a safety cushion for the driver and retractors and locking devices, allowing Control indicator X for driver’s seat belt front passenger. In the event of a side freedom of body movement when the reminder - see page 72. impact, the side airbag system 3 vehicle moves at a constant speed, protects the occupants in the front of the although the spring-tensioned belts are Control indicator k for front passenger’s vehicle, and the curtain airbag system always a snug fit. seat belt reminder 3 - see page 46. protects both front and rear outboard The belt has a “vehicle sensitive retractor” Seat belts are designed to be used by only seat occupants. which is designed to lock during heavy one person at a time. They are only acceleration or deceleration in any suitable for children aged up to 12 or 9 Warning direction. smaller than 150 cm if used in conjunction with a child restraint 3. The airbag system serves to supplement 9 Warning the three-point seat belts and belt For children up to 12 years of age, we tensioners. The seat belts must therefore recommend the Opel child restraint Always wear your seat belt, and that system 3 - see page 47. always be worn. means also in urban traffic and when you Disregard of these notes can lead to are a rear seat passenger. It can save injuries which may be fatal. Vehicle your life! passengers must be informed Pregnant women too must always wear a accordingly. seat belt, keeping the lap belt low and Be sure to read the descriptions of all the snug on the hips and pelvis (not the waist restraint systems on the following pages. or abdomen, where actuating belt tensioners could cause serious injury in the event of a collision). 44 Seats, interior
Belt force limiters Actuation of belt tensioners Load limiters on the front seats reduce the The belt tensioners actuate only once and impact on the seat occupant’s body from a must be replaced by a workshop after tensioning belt, in the event of a severe activation. frontal collision. The belt force is controlled, to reduce the risk of belt-inflicted injury. 9 Warning
Inspection of belts The belt tensioners are operational only Periodically inspect all parts of the belt when control indicator v is unlit. system for damage and to make sure they If the control indicator does not flash are functioning properly. briefly when the ignition is on, stays lit, Have damaged parts replaced. After an illuminates or flashes whilst driving, the accident, belts and triggered belt belt tensioners or the airbag systems may tensioners must be replaced by new ones. not function correctly. Do not perform any alterations on the Belt tensioners Have both systems inspected by a belts, their anchorages, the automatic The seat belt systems on the front seats workshop. retractors or the belt buckles. incorporate belt tensioners housed in the belt buckles and seat belt retractors. Make sure that belts are not damaged or The seat belts remain fully operational In the event of frontal collisions or side trapped by sharp-edged objects. even when the belt tensioners have been impacts of a certain severity, belt buckles actuated. and seat belt retractors tighten the seat belts; the shoulder and lap belts are instantaneously tightened to fit the occupant’s body more snugly. The belt buckles and seat belt retractors will remain locked after actuation (where some noise will occur and smoke may be released). Belt tensioners are not designed to activate in the event of rear impacts, minor side impacts, rollovers or minor frontal collisions. Seats, interior 45
The system’s integrated self-diagnostics z The belt tensioner and airbag system allows faults to be quickly remedied. control electronics can be found in the Important centre console area. In order to avoid z Accessories not released for your vehicle malfunctions, do not store magnetic type and other objects must not be fixed objects in this area. or placed within the action zone of the z When using the rear seats, ensure that belt tensioners, as they may result in the front seat belt components are not injury if the belt tensioners are triggered. damaged by shoes or other objects. z Do not make any modifications to the Avoid dirt getting in the retractors. components of the belt tensioners, as z The belt tensioners only actuate once, this may result in unintended actuation indicated by continuous illumination of of the belt tensioners, rendering the control indicator v in the instrument vehicle unroadworthy and causing panel. Deployed belt tensioners must be serious personal injury. replaced by a workshop. Belt tensioners control indicator z The seat belt tensioners are monitored 9 Warning When disposing of the vehicle, observe electronically together with the airbags, the applicable safety regulations. Take the vehicle to a recycling company for and their operational readiness shown by Improper handling (e.g. removal or disposal. the red control indicator v in the installation) can activate the belt instrument panel. tensioners – risk of injury. When the ignition is switched on, the control indicator flashes several times then extinguishes. If it does not flash, stays lit, illuminates or flashes whilst driving, there is a fault with the belt tensioners or in the airbag systems. The systems might not therefore be triggered in the event of an accident (see also page 56). 9 Warning
Have the cause of the fault remedied by a workshop. 46 Seats, interior
Using the belts Front passenger’s seat belt reminder k 3 Fitting the belt 9 Warning Illuminates for approx. 4 seconds when Pull the belt out evenly from the retractor ignition is switched on. On pregnant women in particular, and guide it over the shoulder, making When the engine is running, if the front certain that it is not twisted. the lap belt must be positioned as low as possible across the pelvis in order to passenger’s seat is occupied and the belt is Insert the latch plate into the buckle. prevent pressure on the abdomen. not engaged, the control indicator will The seat backrest must not be tilted back flash for approx. 90 seconds and then too far (the recommended maximum tilting illuminate until the belt is fastened angle is approx. 25°). Keep knees pointing straight forward so correctly (control indicator will extinguish that driver’s side knee bolsters can help immediately). The lap belt must not be twisted and must prevent submarining under the seat belt in fit snugly across the body. Tension the belt the event of a collision. If vehicle speed exceeds approx. 22 km/h frequently whilst driving by tugging the (14 mph), the control indicator will flash for diagonal part of the belt. Bulky clothing prevents the belt from fitting approx. 90 seconds along with a warning properly. The belt must not rest against chime, and then illuminate until front hard or fragile objects in the pockets of passenger’s seat belt is fastened. your clothing (e.g. ballpoint pens, keys, X spectacles) because these could cause Control indicator for driver’s seat belt injury in the event of a collision. Do not reminder - see page 72. place any objects (e.g. handbags) between the belt and your body. Seats, interior 47
Child restraint systems 3 Opel child restraint systems are designed specifically for your vehicle and thus provide optimum safety for your child in the event of an impact. The use of an Opel child restraint system is therefore recommended. If a different child safety seat is used, follow the manufacturer’s instructions for fitting and use. 9 Warning
Disregard of these instructions may lead Seat belt height adjustment Removing the belt to injuries or endanger life. of front seat belt upper anchorage points To remove the belt, press the red release z Do not adjust height whilst driving. button on the belt buckle; the belt will retract automatically. Selecting the right system z Squeeze release buttons together and Your child should be transported facing slide adjuster up or down to desired Guide the belt as it retracts, to prevent rearwards in the vehicle as long as position. personal injury and damage to interior possible. The child’s neck area is still very surfaces. z Ensure sliding height adjuster latches weak and in an accident they suffer less into position. Always ensure you position the release stress in the semi-prone rearward position button so that you can unbuckle the seat than when sitting upright. Height adjuster can also be moved up belt quickly if necessary. without squeezing release buttons. 48 Seats, interior
Note z Do not stick anything on the child The following Opel child restraint systems z Children under 12 years or under 150 cm restraint systems and do not cover them have been approved for installation in your tall should only travel in an appropriate with any other materials. Antara: child safety seat. z Only allow children to enter and exit the Group, weight and age Opel z Never carry a child whilst travelling in the vehicle at the side facing away from the class 1) system vehicle. The child will become too heavy traffic. to hold in the event of a collision. 0 From birth - 10 kg, Baby Safe z A child restraint system which has been 0 - 10 months z When transporting children, use a child subjected to stress in an accident must restraint system that is suitable for the be replaced. 0+ From birth - 13 kg, 0 - 2 years child's weight, age and height. z When the child restraint system is not in z Ensure that the child restraint system to use, secure the seat with a seat belt or I From 9 - 18 kg, Duo ISOFIX be installed is compatible with the remove it from the vehicle. 8 months - 4 years II From 15 - 25 kg, Kid vehicle type. z The covers of the Opel child restraint 3 years - 7 years z You should always observe the system can be wiped clean. instructions on installation and use III From 22 - 36 kg, supplied with the child restraint system. 6 years - 12 years 1) We recommend the use of each system until the child reaches the upper weight limit.
If child restraint systems of other manufacture are to be installed, ensure that they conform to the appropriate safety regulations. Seats, interior 49
Permissible options for fitting a child safety seat U = Universal suitability in conjunction Weight and age class On front passenger’s On outboard rear On centre rear seat with the three-point seat belt. seat seats + = Vehicle seat with ISOFIX mounting 0: available. When mounting with up to 10 kg ISOFIX, only ISOFIX child restraint or approx. XU, +X systems that have been approved 10 months for the vehicle may be used. 0+: up to 13 kg ++= Vehicle seat with ISOFIX fixings or approx. XU, +X available. For use of ISOFIX and 2 years top tether fixings, universal ISOFIX I: child restraint systems may be 9 to 18 kg used. or approx. X U, +, ++ X 8 months to 4 years X = No child restraint system II: permitted in this weight and age 15 to 25 kg class. or approx. XUX 3 to 7 years 9 Warning III: 22 to 36 kg Disregard of these instructions may lead or approx. XUXto injuries or endanger life. 6 to 12 years 50 Seats, interior
ISOFIX child restraint systems 3 Size class Description D - ISO/R2: Rear-facing The instructions accompanying the ISOFIX A - ISO/F3: Forward-facing child restraint system for child restraint system are to be expressly child restraint system for smaller children in the followed. children of maximum size in weight class up to 13 kg. IL = Suitable for particular the weight class 9 to 18 kg. ISOFIX child restraint E - ISO/R1: Rear-facing systems specified in the B - ISO/F2: Forward-facing child restraint system for list. child restraint system for young children in the smaller children in the weight class up to 13 kg. These ISOFIX systems are weight class 9 to 18 kg. of the ’vehicle-specific’, ’restricted’ or ’semi- B1 - ISO/F2X: Forward-facing universal’ type. child restraint system for smaller children in the IUF = Suitable for ISOFIX weight class 9 to 18 kg. forward-facing child restraint systems of C - ISO/R3: Rear-facing universal category child restraint system for approved for use in this children of maximum size in weight and age class. the weight class up to 13 kg. X = No child restraint system permitted in this weight and age class. Seats, interior 51
Permissible options for fitting an ISOFIX child safety seat Weight and age class Size class Fixture On front passenger’s On outboard rear On centre rear seat seat seats 0: up to 10 kg or approx. EISO/R1X ILX 10 months 0+: up to 13 kg EISO/R1X ILX or approx. 2 years DISO/R2X ILX
CISO/R3X ILX I: 9 to 18 kg DISO/R2X ILX or approx. 8 months to CISO/R3X ILX 4 years BISO/F2X IUFX
B1 ISO/F2X X IUF X
AISO/F3X IUFX 52 Seats, interior
Mounting brackets for ISOFIX child Anchors for Top-Tether child restraint Airbag systems restraint systems systems Front airbags The brackets located between the backrest The top tether anchors located on the rear The front airbag system is identified by the and seat cushion are used for mounting of the backrests are designed to hold child word “Airbag” on the steering wheel and ISOFIX child restraint systems. restraints which come equipped with top above the glove compartment. tether anchor attachments only. The instructions accompanying the ISOFIX The front airbag system comprises: child restraint system are to be expressly Please be sure to follow the instructions z an airbag with an inflator in the steering followed. provided with the Top-Tether child wheel, and a second one behind a trim Only ISOFIX child restraint systems restraint system. panel above the glove compartment, approved for the vehicle may be used. For use of ISOFIX and Top-Tether fixings, z the control electronics, universal ISOFIX child restraint systems may be used. z the front impact sensor, z the airbag system control indicator v in the instrument panel. Seats, interior 53
When triggered, the driver’s and front The front airbag system will not be passenger’s airbags inflate in milliseconds triggered in the event of: and form safety cushions for the driver and z the ignition being switched off, front passenger. Forward movement of z minor frontal collisions, driver and front passenger is checked and the risk of injuries to the upper body and z accidents in which the vehicle overturns, head thereby substantially reduced. z collisions involving a side or rear impact z No impairment of view will occur, as where it would not be of benefit to the airbags inflate and deflate so quickly. occupants. 9 Warning 9 Warning
The front airbag system provides Seat belts must therefore always be worn. optimum protection when the seat, seat The front airbag system serves to The front airbag system is triggered: belt, backrest and head restraint are supplement the three-point seat belts. z depending on the severity of the correctly adjusted. If you do not wear your seat belt, you risk accident, Adjust the driver's seat according to the being seriously injured, or even thrown z depending on the type of impact, occupant's height such that, with the from the vehicle, in the event of an driver sitting upright, the steering wheel is accident. z within the range shown in the illustration, held in the area of its upper spokes with The belts help to maintain occupants in z independently of the side airbag 3 and the driver's arms slightly bent. the correct seating position for the front curtain airbag systems. The driver’s seat should be as far back as airbag system to provide effective Examples: possible without compromising the protection in the event of an accident. z Impact against a non-yielding obstacle; driver’s ability to reach the pedals, the front airbags are triggered at low steering wheel or controls. vehicle speeds, The front passenger’s seat should be as z Impact against a yielding obstacle (such far back as possible, with the backrest as another vehicle); the front airbags are upright. Do not place the head, body, only triggered at a higher vehicle speed. hands or feet on the cover of the airbag system. Do not place objects, children or pets in the area in which the airbags inflate. 54 Seats, interior
When triggered, the side airbag inflates in milliseconds and forms a safety cushion for the driver and/or front passenger in the respective door area. The risk of injury to the upper body and pelvis in the event of a side impact is thereby substantially reduced. 9 Warning
There must be no objects in the area in which the airbag inflates or in the area between the seat backrests and the vehicle body. Side airbags 3 The side airbag system will be triggered: Do not place hands, arms or other body The side airbags are identified by the word z depending on the severity of the parts on the covers of the airbag systems. "Airbag" on the outboard sides of the front accident, Important information - see page 57. seat backrests, and protect front seat z depending on the type of impact, occupants in the event of a severe side The three-point seat belt must always be impact. z within the range shown in the illustration, correctly fitted - see page 43. The side airbag system comprises: z independently of the front airbag z an airbag with inflator in the outboard system. sides of the driver's and front passenger's seat backrests, z the control electronics, z the side impact sensors, z the airbag systems control indicator v in the instrument panel. Seats, interior 55
The side airbags will not be triggered in the event of: z the ignition being switched off, z frontal collisions, z accidents in which the vehicle overturns, if lateral impact is insufficient for side airbag deployment, z collisions involving a rear impact, z collisions involving a side impact outside the passenger cell.
Curtain airbags The curtain airbag system will be triggered: The curtain airbag system is identified by z depending on the severity of the the word "Airbag" on the roof frame, and accident, protects front seat and rear outboard seat z depending on the type of impact, occupants in the event of a severe side impact. z within the range shown in the illustration, The curtain airbag system comprises: z together with the side airbag system, z an airbag with inflator in the roof frame z independently of the front airbag above the doors on the driver’s and system. passenger’s side respectively, z the control electronics, z the side impact sensors, z the airbag systems control indicator v in the instrument panel. 56 Seats, interior
When triggered, the curtain airbag inflates The curtain airbags will not be triggered in in milliseconds and provides a safety the event of: barrier in the head area on the respective z the ignition being switched off, side of the vehicle. This reduces the risk of z frontal collisions, injury to the head considerably in the event of a side impact. z accidents in which the vehicle overturns, if lateral impact is insufficient for curtain 9 Warning airbag deployment, z collisions involving a rear impact, There must be no objects in the area in which the airbag inflates. Do not place z collisions involving a side impact outside hands, arms or other body parts on the the passenger cell. covers of the airbag systems. Never secure anything to the roof by routing ropes through the doors or Airbag control indicator v windows, to avoid obstructing inflation of The front airbag system, side airbag the curtain airbags. system 3 and curtain airbag system Important information – see page 57. are monitored electronically together with the belt tensioners, and their operational The three-point seat belt must always be readiness is shown by the red control correctly fitted – see page 43. indicator v in the instrument panel. When the ignition is switched on, the control indicator flashes several times then extinguishes. If it does not flash, stays lit, illuminates or flashes whilst driving, there is a fault in the airbag systems or with the belt tensioners. The systems might not therefore be triggered in the event of an accident (see also page 45). Seats, interior 57
Important z Use only a dry cloth or interior cleaner to 9 Warning z Accessories not released for your vehicle clean the steering wheel, instrument type and other objects must not be panel, front seat backrests, roof frame Have the cause of the fault remedied by affixed or placed in the area in which the and seat area of the front seats. Do not a workshop. airbags inflate, as they could cause use any aggressive cleaning agents. injury when the airbags are triggered. z Only protective covers which are The system's integral self-diagnosis facility z Do not place any objects between the approved for your vehicle with side allows faults to be quickly remedied. airbag systems and the vehicle airbags 3 may be fitted on the front occupants; danger of injury. seats. When fitting the protective covers, 9 Warning z Only use the hooks on the assist grips in make sure that the airbag units on the the roof frame to hang up light articles of outboard sides of the front seat Disregard of these instructions may lead backrests are not covered. to injuries or endanger life. clothing or coat hangers. Do not place any objects in the pockets of the hanging z The airbag systems are triggered items; risk of injury. independently of each other, depending z Do not stick or place anything on the on the severity of the accident and the 3 steering wheel, instrument panel, front type of impact. The side airbag system seat backrests in the vicinity of the and the curtain airbag system are airbags and seat areas or cover them triggered together. with other materials. z During off-road driving especially, z The airbag systems and belt tensioner airbags can also inflate in moderate to control electronics can be found in the severe non-collision situations such as centre console area. In order to avoid when slamming the undercarriage or malfunctions, do not store magnetic other solid components of the vehicle in objects in this area. a dip in the driving surface. z Each airbag can be triggered only once. Once triggered, an airbag must be replaced immediately by a workshop. 58 Seats, interior z After airbags deflate, you may notice a z We recommend having the steering burning smell, smoke and white powder wheel, the instrument panel, all panelling in the interior, which is normal. Although parts, the door seals, handles and the they may cause skin or eye irritation, front seats removed by a workshop. these substances are non-toxic. z When disposing of the vehicle, please z Hazard warning lamps may flash and observe the applicable safety locked doors may be unlocked regulations. Take the vehicle to a automatically when airbags deploy 3. recycling company for disposal. z The speeds, directions of movement and deformation properties of the vehicles, 9 Warning and the properties of the obstacle Child restraint systems as well as other concerned, determine the severity of the heavy objects must never be carried on accident and triggering of the airbags. the lap of passengers; risk of fatal injury. z The degree of damage to your vehicle Use of child restraint systems 3 on front and the resulting repair costs alone are passenger’s seat not indicative that the criteria for triggering of the airbags were met. 9 Warning z Do not perform any modifications to the components of the airbag systems, as No child restraint system may be this will render the vehicle unroadworthy. installed to the front passenger’s seat. Danger to life. 9 Warning
The systems can be triggered abruptly and cause injury if they are handled improperly. Seats, interior 59
Notes on loading the vehicle: See page 63. 9 Warning
Do not place any heavy or sharp objects on the cover. Loose objects in the luggage compartment should be secured safely.
Storage To remove Luggage compartment cover Open luggage compartment cover. To close Pull socket on either side of cover towards Pull luggage compartment cover towards centre of vehicle, lift and remove cover rear of vehicle using handle and insert from the side guides. retainers into brackets on either side of Fit in reverse order. luggage compartment. To open Remove luggage compartment cover from side brackets. It rolls up automatically. 60 Seats, interior
Safety net 3 The safety net can be mounted behind the rear seats or, if the rear seat backrests are folded, in front of the rear seats. Passengers must not be transported behind the safety net.
Fitting In front of and behind the rear seats on There are four installation openings in the both sides of the vehicle are the hook roof frame, two located in front of and two holders (lashing eyes) for the lower strap behind the rear seats. hooks. When fitting behind the rear seats, remove Hang strap hooks in the two lashing eyes. the luggage compartment cover - Pull on the straps to take up any slack. see page 59. When fitting in front of the rear seats, fold down rear seat backrests - see page 41. Open aperture covers on the roof frame and insert top corners of safety net into large apertures in roof frame and secure by sliding them into the smaller apertures. Seats, interior 61
Designed for carrying small, light items 9 Warning only, the luggage floor net 3 helps keep loads from moving during sharp turns or Do not stack loads higher than the upper quick starts and stops. end of the safety net. To install: attach the four net hooks to the Avoid applying excessive force to the lashing eyes mounted on the luggage safety net or hanging heavy items from it. compartment floor. Do not place loads behind the safety net which have sharp edges that could pass 9 Warning through the net in the event of heavy braking, for example. Do not carry heavy objects in the luggage floor net. Loose objects in the luggage compartment should be secured Removing safely. Loosen straps by pulling up strap adjusters Lashing eyes and remove the strap hooks from the Lashing eyes are mounted on the luggage lashing eyes. compartment floor, to enable loads to be Pull top corners of safety net from the secured in position using lashing straps 3 smaller apertures into the larger apertures or a luggage floor net 3. Two lashing eyes and remove. are located in front of the rear seats for fitting a safety net 3 - see page 60. 62 Seats, interior
FlexOrganizer 3 Variable partition net Hooks and mesh pocket Flexible system for dividing the luggage Insert an adapter in each rail: fold up Insert the hooks in the desired position in compartment or securing loads. handle plate, insert adapter in upper and the rails: insert the hook in the upper The system consists of: lower groove of rails, move to desired groove on the rail and press in the lower position. groove. The mesh pocket can be hung from z adapters the hooks. z variable partition net To lock the adapter, swivel the handle z mesh pockets for the side walls plate up. Compress the rods of the Removing z hooks in the luggage compartment partition net slightly and insert in Press the partition net rods together and corresponding openings of the adapter. remove from the adapters. Components are mounted in the two guide The longer rod must be inserted in the Adapter: fold open the retainer, release the rails in the side walls of the luggage upper adapter. compartment by means of adapters or adapter from the lower groove and remove hooks. from the upper groove. Release the hooks from the rails. Seats, interior 63
Notes on loading the vehicle z Heavy objects in the luggage compartment should be placed as far forward as possible. If objects are to be stacked, the heavier objects should be placed at the bottom. With rear seats in the folded position, or with safety net 3 installed behind rear seats, objects must not be stacked higher than the seat backrests. Unsecured objects in the luggage compartment would be thrown forward with great force in the event of heavy braking, for example. Luggage compartment storage 3 Luggage compartment under floor Trays on both sides of the luggage storage 3 z Secure heavy objects with lashing compartment floor. To access the under floor storage, push straps 3 attached to the lashing eyes. If both levers on floor cover towards the heavy loads slip when the vehicle is handle - see page 176. Pull floor cover braked heavily or driven around a bend, upwards by the handle and hang the hook the handling of the vehicle may change. to the upper part of the tailgate opening. z Secure loose items in luggage compartment using FlexOrganizer 3 or 9 Warning luggage floor net 3 to prevent sliding. z Do not allow objects to protrude above When transporting objects in the 3 the top of the under floor storage, to luggage compartment, fit safety net - avoid damage to the storage area and see page 60. the luggage compartment floor. 64 Seats, interior z Close the luggage compartment cover to z The load must not obstruct the operation prevent the objects from being reflected of the pedals, hand brake and gearshift in the rear window. lever or hinder the freedom of movement z If the backrests are not folded down of the driver. Do not place any unsecured when transporting objects in the objects in the interior. luggage compartment, they must be z Bulky objects should not be transported engaged in their upright position - with the tailgate open or ajar, otherwise see page 41. poisonous exhaust fumes may enter the z Do not allow the load to protrude above vehicle. the upper edge of the rear seat z Weights, payload and roof load - backrests, or if the rear seat backrests see page 221. have been folded down onto the seat z Driving with a roof load (see also cushions, above the upper edge of the page 127) increases the sensitivity of the front seat backrests. vehicle to crosswinds and has a Stowage compartments z The warning triangle 3 and first aid kit 3 detrimental effect on vehicle handling Glove compartment should always be freely accessible. owing to the higher centre of gravity of To open, pull handle upwards. the vehicle. z No objects should be placed on the The glove compartment will illuminate luggage compartment cover or the when opened. instrument panel. They are reflected in 9 Warning the glass, obstruct the driver’s view and The glove compartment partition can be Disregard of these instructions may lead will be thrown through the vehicle in the removed from its groove. to injuries or endanger life. Vehicle event of heavy braking, for example. passengers must be informed Store the partition in the groove on the far z No objects should be stored in any of the accordingly. left-hand side of the glove compartment. airbag inflation zones, as injuries may be caused when the airbag is triggered. 9 Warning Do not drive with glove compartment open; risk of injury in the event of heavy braking or a collision.
Glove compartment cooling 3 - see page 105. Seats, interior 65
Sunglass holder Console box in front armrest 3 Console box in rear armrest 3 To open: push the rear part of the front To open: pull up lower lever and lift the lid. To open: pull up lid of rear centre armrest. reading lamps cover. To close: lower lid and push it down until it To close: lower lid and push it down until it To close: pull up cover and push it until it latches into position. latches into position. latches into place. To use the tray 3: ensure armrest is in its Do not store heavy items in the stowage rearmost position, pull up on upper lever compartment. and lift the lid. 66 Seats, interior
Console net 3 Front passenger’s seat undertray 3 Storage compartment 3 Located in the front passenger’s footwell. Pull up on front of tray then pull it forwards. Located in rear of centre console. Push the tray towards the seat to return it To open: press button above the storage to its original position. compartment. Seats, interior 67
Card holder Ashtrays 3 Located below instrument panel on driver’s To be used only for ash and not for side. Insert a card into the slot for combustible rubbish. convenient use. 9 Warning Coin storage Open by pulling handle on coin storage Disregard of these instructions may lead door (located below card holder) towards to injuries or endanger life. Vehicle you. Push door firmly to close. passengers must be informed accordingly.
Drink holders Located in the front 3 and rear of the centre console. The front drink holder is a fixed size. The rear drink holder is flexible, allowing different size drink containers to be stored. To open: press button above rear drink holder. 68 Seats, interior
Warning triangle ¨ 3, First aid kit + 3 Your first aid kit and warning triangle can be accommodated below the floor cover in the luggage compartment.
Portable front ashtray 3 Power outlets Located in front drink holder. Cigarette lighter ) To open: gently lift up lid. Illuminates With ignition switch in positions ACC or ON, depending on outside light conditions. push the cigarette lighter in all the way. To empty: rotate upper part of ashtray Heating up ceases once element is anti-clockwise and remove. glowing; cigarette lighter pops up automatically. Withdraw lighter. After use, close lid firmly. To replace battery: remove screw on ashtray lid and replace with CR2032 (or equivalent) battery. Seats, interior 69
Accessory sockets The maximum power requirement of Assist grips Located in the rear centre console between electrical accessories must not exceed Located above the driver’s door 3, the the front seats and in the right-hand side of 120 watts. front passenger’s door and both rear 3 the luggage compartment . Do not connect any current delivering doors. Operational with ignition switch in accessories, e.g. electrical charging Pull grip down and hold to assist when positions ACC or ON. devices or batteries. entering or exiting the vehicle. Grips swing Pull the cap out to use the accessory Connected electrical accessories must back up automatically when released. socket, and replace it when not in use. comply with the EC standard in terms of Rear door assist grips also include coat The socket for the cigarette lighter can also electromagnetic compatibility hangers. be used to connect electrical accessories requirements laid down in DIN VDE 40 839, when the ignition is switched on. otherwise vehicle malfunctions may occur. Use of accessory sockets while the engine is The use of non-authorised accessories may not running will discharge the battery. cause damage to the socket. 70 Instruments, controls Instruments, controls
Control indicators ...... 70 Instrument display...... 75 Information display ...... 76 Display of current tyre pressure 3 .... 91 Check control 3 ...... 91 Warning buzzers...... 92 Windscreen wipers...... 92 Control indicators 4 The control indicators described here are Brake system not present in all vehicles. The description Illuminates in red when ignition is switched applies to all instrument versions. on. Extinguishes after engine is started. The colours of the control indicators mean: Illuminates when engine is running if hand brake is applied and/or fluid level for z Red Danger, important reminder, brake hydraulics is too low. z Yellow Warning, information, fault, z Green Confirmation of activation, 9 Warning z Blue Confirmation of activation. If it illuminates when the hand brake is u not applied: stop vehicle; interrupt your ABS (Anti-lock Brake System) journey immediately. Consult a see page 148. workshop. g Trailer indicator 3 Further information - see page 145. Illuminates in green when a trailer is connected to the vehicle. Extinguishes when the trailer is disconnected. Instruments, controls 71 r B q Park pilot 3 AWD (All Wheel Drive) Automatic headlamp range Illuminates in yellow when ignition is Illuminates in yellow when ignition is adjustment 3 switched on, then extinguishes. switched on, then extinguishes. Illuminates in yellow when ignition is If it stays illuminated while driving, there is If it flashes during driving, the AWD system switched on, then extinguishes. a fault in the system - see page 142. is temporarily disabled. Comes on during driving to indicate a fault that requires immediate attention. Consult 5 If it illuminates, there is a fault in the system. Consult a workshop as soon as a workshop as soon as possible. DCS (Descent Control System) possible. Further information - see page 97. Both control indicators illuminate when ignition is switched on, then extinguish. Further information - see page 121. W Green; illuminates when DCS is ready for 7 Coolant temperature operation. Flashes during driving when ESC Active & Warning Illuminates in red when ignition is DCS is in operation, after pressing the (Electronic Stability Control) switched on, then extinguishes. DCS button. see page 136. If it illuminates when the engine is running: Yellow; flashes to indicate system is not stop vehicle and switch off engine. Coolant ready for conditions to operate. A temperature is too high; danger of engine Illuminates to indicate there is a fault in the ESC Not Ready damage. Check coolant level. system. see page 136. 9 Warning If the yellow control indicator flashes or J illuminates during driving, friction material ESC OFF Allow engine to cool down before needs to cool down: drive the vehicle see page 136. removing coolant filler cap. without braking as much as possible.
Further information - see page 138. Further information - see page 195. 72 Instruments, controls o 1 O Electronic immobiliser Tailgate open Turn signal lamps Illuminates in red when ignition is Illuminates in red when ignition is The relevant control indicator flashes in switched on, then extinguishes. switched on, then extinguishes. green when the turn signal is on. If it remains illuminated after the ignition is Illuminates when tailgate is open or not Rapid flash; failure of a turn signal bulb or on, there is a fault in the immobiliser securely latched. the corresponding fuse or failure of a trailer 3 system; the engine cannot be started - Tailgate - see page 26. turn signal bulb . Both control indicators see page 22. flash when the hazard warning lamps are X active. 9 Driver’s seat belt reminder Further information - see pages 14, 95. Door open Illuminates in red when ignition is Bulb replacement - see page 185. Illuminates in red when a door is open. switched on, then extinguishes. Fuses - see page 181. 3 When the engine is running, if driver’s seat Y Engine electronics, belt is not engaged, it will flash for approx. Low fuel level transmission electronics 3 90 seconds and then illuminate until Illuminates in yellow when ignition is Illuminates in yellow when ignition is driver’s seat belt is fastened. switched on, then extinguishes. switched on, then extinguishes. If vehicle speed exceeds approx. 22 km/h If it illuminates during driving; fuel level low: If it illuminates during driving; (14 mph), control indicator will flash for fill up fuel tank as soon as possible. there may be a fault in the engine or approx. 90 seconds along with a warning transmission electronics: interrupt your chime and then remains illuminated until Never let the tank run dry. journey and consult a workshop as soon as driver’s seat belt is fastened. Erratic fuel supply can cause catalytic possible. Seat belts - see page 43. converter to overheat - see page 133. Further information - see page 134. Diesel engines: if the tank has been run dry, v bleed the fuel system as described on page 171. Airbag systems 3, belt tensioners see pages 44, 52. Refuelling - see page 132. Fuel tank capacity - see page 225. Instruments, controls 73
> C m Front fog lamps Change engine oil 3 Cruise control 3 Illuminates in green when front fog lamps Illuminates in yellow when ignition is see page 140. are switched on - see page 96. switched on, then extinguishes. S Illuminates to indicate that engine oil r Engine oil level 3 needs changing within approx. 1000 km Fog tail lamp Illuminates in yellow when ignition is (600 miles). Engine power may be Illuminates in yellow when the fog tail lamp switched on, then extinguishes. decreased. is switched on - see page 96. If it illuminates during driving; Once the engine oil has been changed, the oil level low: top up oil to specified level - P engine oil life monitor needs to be reset - see page 192. Headlamp main beam see page 194. Illuminates in blue when main beam is on 2 N and when headlamp flash is operated - Power steering Preheating for diesel engines 3 see pages 14, 95. Illuminates in yellow when ignition is Illuminated in yellow during preheating. G switched on, then extinguishes. Preheating system switches on only if Low windscreen washer fluid If it does not illuminate when the ignition is outside temperature is low. Illuminates in yellow when ignition is switched on, stays illuminated or switched on, then extinguishes. If it comes on during driving or if the engine illuminates during driving, there is a fault in cannot be started, consult a workshop as the system. Consult a workshop as soon as If it illuminates: windscreen washer fluid soon as possible. possible. level low, add washer fluid as soon as possible - see page 199. Starting the engine - see page 19. N I Water in diesel fuel filter 3 DPF (Diesel particle filter) 3 Illuminates in yellow when water level in Illuminates in yellow when diesel particle diesel fuel filter exceeds a specified level. filter requires cleaning. Residual water in the diesel fuel filter will As soon as the road and traffic situation need to be drained - see page 194. Consult permits it, increase speed to more than a workshop as soon as possible. 50 km/h (30 mph) for approx. 15 minutes. The control indicator extinguishes as soon as cleaning is complete. Further information - see page 135. 74 Instruments, controls a Z Anti-theft alarm system activation 9 Warning Exhaust emissions without monitoring of passenger Illuminates in yellow when ignition is compartment and vehicle tilt 3 When the engine is off, considerably switched on. Extinguishes after engine is see page 28. greater force will be required for braking started. Can illuminate briefly when and steering. driving; this is normal and does not I Do not remove key until vehicle has come indicate a system fault. Engine oil pressure to a standstill, otherwise the steering If it illuminates when the engine is running; Illuminates in red when ignition is switched column lock could engage unexpectedly. fault in emission control system. on. Extinguishes after engine is started. The permitted emission limits may be Can illuminate intermittently when idling exceeded. Fuel economy and vehicle with hot engine; must extinguish when Check engine oil level before consulting driveability may be impaired. engine speed is increased. a workshop. If the oil level is low, top up using the specified engine oil - see pages The control indicator also illuminates if If it illuminates during driving; 192, 213, 217. there is a fault in the diesel particle filter 3. engine oil pressure may be dangerously Consult a workshop as soon as possible. low, interrupting engine lubrication and If the oil level is normal, have a workshop resulting in damage to the engine and/or check the vehicle’s lubricating system. If it flashes when the engine is running; locking of the driving wheels: for a fault that can lead to destruction of p the catalytic converter, see page 134. z Move out of the flow of traffic as quickly Alternator Consult a workshop as soon as possible. as possible without impeding other Illuminates in red when ignition is switched vehicles, on. Extinguishes after engine is started. 0 z Depress clutch, Winter program 3 z Move gearshift lever to neutral If it illuminates during driving: stop vehicle and switch off engine. The Illuminates in yellow when Winter program (automatic transmission to N), for the automatic transmission is enabled - z Switch off ignition. battery is not being charged and the engine cooling may be interrupted. The see page 117. brake servo unit may cease to be effective. Interrupt your journey immediately. Remove key and check drive belt condition and tensioning before consulting a workshop. Instruments, controls 75
Instrument display Speedometer Odometer Tachometer Indicates the vehicle speed. The odometer indicates how far the vehicle Making use of the tachometer helps to has been driven. save fuel; it indicates the engine speed in Trip odometer revolutions per minute (rpm). There are two independent trip odometers Red warning zone on right; maximum which indicate how far the vehicle has been permissible engine speed exceeded, driven since the last reset. danger to engine. Press the trip odometer button once to If possible, drive in each gear in the low toggle between Trip A and Trip B. engine speed range (between approx. To reset a trip odometer, press and hold 2000 and 3000 rpm) and maintain an even the trip odometer button. vehicle speed to maximise fuel efficiency. 76 Instruments, controls
11:25} 21.5°C Range
RDS [TP] 257km
Fuel gauge Transmission display 3 Information display Indicates fuel level when the ignition is on. Display of the selected gear or mode with Board information display 3 After adding fuel and restarting engine, automatic transmission . Display of time, outside temperature and fuel gauge pointer slowly moves to show P Park position. date/Infotainment system (when it is on). new fuel level. R Reverse gear. An F in the display indicates a fault. When fuel gauge indicates that fuel supply N Neutral. Have the cause of the fault remedied by a is low, control indicator Y illuminates: D Automatic mode. workshop. fill up fuel tank as soon as possible - 1 to 5 Selected gear in manual see page 132. mode. Never let the fuel tank become empty. Diesel engines: if the tank has been run dry, bleed the fuel system as described on page 171. Because of the amount of fuel remaining in the tank, the amount of fuel required to fill the tank may be less than the specified tank capacity. Instruments, controls 77
The type of information and how it is displayed depends on the equipment of the vehicle and the settings of the trip computer 3 and Infotainment system. : Some information appears on the display 11:25} -1.5°C Range 257 km in an abbreviated form. Infotainment system – see Infotainment Range Aver. Consump. 7.0 Ltr./100km system instruction manual. RDS [TP] Inst. Consumpt. 7.6 Ltr./100km An F in the display indicates a fault. Have the cause of the fault remedied by a 257km 19,5° 19:36 workshop.
Graphical information display 3, Outside temperature colour information display 3 A fall in temperature is indicated Display of time, outside temperature, and immediately and a rise in temperature date/Infotainment system (when it is on). after a time delay. The graphical information display presents If outside temperature drops to 3 °C, the information in monochrome. The colour the symbol : illuminates in the board information display presents the information display as a warning for information in colour. icy road surfaces. : remains illuminated until outside temperature reaches at least 5 °C. 78 Instruments, controls
11:25} 21.5°C Slippery road Range -2,5°C 257km OK
In vehicles with graphical information Board information display, Select menu items using the arrow buttons: 3 3 display or colour information display , selecting functions OK button Select marked item, a warning message appears on the display Functions and settings of some equipment confirm command. as a warning for icy road surfaces. There is can be accessed via the board information no message below -5 °C. display. This is done via the menus and the buttons 9 Warning on the Infotainment system or with the left adjuster wheel on the steering wheel. The Caution: the road surface may already relevant menu options are then shown on be icy, even though the display indicates the subsequent row of the display. a few degrees above 0 °C. Instruments, controls 79
The functions are displayed in the following order: z Time synchronisation z Time, setting hours 11:25} 21.5°C z Time, setting minutes z Date, setting day z Date, setting month System z Date, setting year z Ignition logic z Language selection z Setting units of measure
To select using the left adjuster wheel on Board information display, the steering wheel: system settings Turn up Previous menu item. Press the Settings button on the Infotainment system. Menu item Audio or Turn down Next menu item. System will appear. Press Select marked item, confirm command. Press the left arrow button to reach menu item System and select. The first function If check control 3 issues a warning of the System menu is marked. message, the display is blocked from other functions. Acknowledge the message by Some of the functions appear on the pressing the OK button or the left adjuster display in an abbreviated form. wheel. If there are several warning messages, acknowledge them one at a time. 80 Instruments, controls
The automatic setting is indicated by } in the display. To correct time with the help of RDS, select the menu item for time synchronisation 11:25} 21.5°C from the Settings menu. 11:25} 21.5°C Make the desired setting. Clock Sync.On Setting date and time English Select the menu item for time and date setting from the Settings menu. Make the desired setting. The setting is saved when the menu item is exited. Correcting time Ignition logic 3 Language selection Some RDS1) transmitters do not send a See Infotainment system instruction You can select the display language for correct time signal. If the incorrect time is manual. some functions. continually displayed, deactivate Select the menu item for language from the 3 automatic time synchronisation and set Settings menu and make the desired the time manually – see next column. setting.
1) RDS = Radio Data System. Instruments, controls 81
Board information display, trip computer 3 The trip computer provides information on driving data, which is continually recorded 11:25} 21.5°C and evaluated electronically. 11:25} 21.5°C Access trip computer vehicle data by pressing the BC button on the Infotainment Unit Europe-SI system or the left adjuster wheel on the Inst. Consumpt. steering wheel. Some of the functions appear on the display in an abbreviated form. 7.6l/100km Once a function has been selected, the subsequent rows of the trip computer Setting units of measure function are displayed. Instantaneous consumption You can select which units of measure are The functions are displayed in the following Display changes depending on speed; to be used. order: Display in l/h below 13 km/h. Select the menu item for units of measure z Instantaneous consumption Display in l/100 km above 13 km/h. from the Settings menu and make the z Average consumption desired setting. z Effective consumption z Average speed z Distance travelled z Range z Stop watch 82 Instruments, controls
Average consumption Resetting trip computer information Display of average consumption. The following trip computer information The measurement can be restarted at any can be reset (restart measurements): time – see "Resetting trip computer z Average consumption information". 11:25} 21.5°C z Effective consumption Effective consumption z Average speed Displays amount of fuel consumed. Range z Distance travelled The measurement can be restarted at any Select the desired trip computer time – see "Resetting trip computer information. information". 257km Reset by pressing the left adjuster wheel on Average speed the steering wheel or the OK button on the Display of average speed. Infotainment system. The measurement can be restarted at any time - see "Resetting trip computer information". Range Range is calculated from current fuel tank Stoppages in the journey with the ignition content and instantaneous consumption. off are not included in the calculations. The display shows average values. Distance travelled The vehicle updates the range Displays number of kilometres (miles) automatically after a brief delay when the driven. The measurement can be restarted vehicle has been refuelled. at any time – see "Resetting trip computer information". If the fuel in the tank will allow less than 50 km (30 miles) of travel, the warning "Range" appears on the display. If the fuel in the tank will allow less than 30 km (20 miles) of travel, the warning "Refuel!" 3 appears on the display. Instruments, controls 83
Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will 11:25} 21.5°C be lost. Range 257 km Stop Watch Aver. Consump. 7.0 Ltr./100km
Inst. Consumpt. 7.6 Ltr./100km 01:22:32h 19,5° 19:36
Stop watch Graphical information display 3 or Operating using the arrow buttons: colour information display 3, To start, press left arrow button to select selecting functions menu item Start and press OK button to The functions and settings of some 3 start/stop. equipment can be accessed via the graphical information display or the To reset, press left arrow button to select colour information display. menu item Reset and press OK button. Functions are selected and executed in the Operating using the left adjuster wheel on menu on the display using the arrow the steering wheel: buttons 3, the multifunction knob 3 on the To start, select menu item Start and press Infotainment system or the left adjuster to start/stop. wheel on the steering wheel. To reset, select menu item Reset and press to confirm command. 84 Instruments, controls
To select using the arrow buttons: To select using the multifunction knob: To select using the left adjuster wheel on Select menu items via menus and with Turn Mark menu items or the steering wheel: the buttons on the Infotainment system. commands, select functions. Turn up Previous menu item. If check control 3 issues a warning Press Select marked item, confirm Turn down Next menu item. message, the display is blocked from other command. Press Select marked item, functions. Acknowledge the message by To exit a menu, turn the multifunction knob confirm command. pressing the right or left arrow button. If left or right to Return or Main and select. If check control 3 issues a warning there are several warning messages, 3 message, the display is blocked from other acknowledge them one at a time. If check control issues a warning message, the display is blocked from other functions. Acknowledge the message by functions. Acknowledge the message by pressing the left adjuster wheel. If there are pressing the multifunction knob. several warning messages, acknowledge If there are several warning messages, them one at a time. acknowledge them one at a time. Instruments, controls 85
777 Settings 19,5° 19:36 777 Time, Date 19,5° 19:36
FM [TP] CDin Time, Date 19:36 Time 19:36 Language ᕃ 90.6 MHz Units 10 . 07 . 2004 Date 10 . 07 . 2004 Contrast
Day / Night 666 Synchron. clock automatical. 19,5° 19:36 666 Ign. logic
For each functional area there is a main Graphical information display 3 or Setting date and time page (Main), which is selected at the colour information display 3, Select menu item Time, Date from the top edge of the display: system settings Settings menu. z Audio The settings are accessed via the Settings The menu for Time, Date is displayed. z 3 menu. Navigation Select the menu items required: z 3 3 Telephone Press the Main button (not found on all make the desired setting. z Trip computer 3 Infotainment systems) on the Infotainment For audio, navigation 3 and telephone 3 system (call up main display). functions – see Infotainment system Press the Settings button on the instruction manual. Infotainment system. On Infotainment System CD 30, make sure no menu has been selected. The Settings menu is displayed. 86 Instruments, controls
Correcting time 3 With the navigation system, date and time are set automatically upon receipt of a GPS1) satellite signal. If the displayed time 777 Settings 19,5° 19:36 777 13 Languages 19,5° 19:36 does not match local time, it can be Time, Date corrected manually or automatically by X Deutsch receiving an RDS2) time signal 3. Language Deutsch English Some RDS transmitters do not send correct Units English Español time signals. If the incorrect time is Contrast Español Nederlands displayed often, deactivate automatic Day / Night ... Français time synchronisation 3 and set the time manually. 666 Ign. logic Italiano To correct time with the help of RDS, select menu item Synchron. clock automatical. from the Time, Date menu. Language selection Select the desired language. You can select the display language for Selections are indicated by a 6 in front of The box in front of Synchron. clock some functions. automatical. will be ticked: the menu item. see Fig. 17340 T. Select menu item Language from the In systems with voice output 3, when the Settings menu. language setting of the display is changed, The available languages are displayed. the system will ask whether the announcement language should also be changed – see Infotainment system instruction manual.
1) GPS = Global Positioning System, satellite system for world-wide positioning. 2) RDS = Radio Data System. Instruments, controls 87
Setting display mode 3 The display can be adjusted to suit the light conditions: black or coloured text on a light 777 Settings 19,5° 19:36 777 Contrast 19,5° 19:36 background or white or coloured text on a dark background. Time, Date Select menu item Day / Night from the Language ~ Europe-SI Settings menu. Units | Japan 12 The options are displayed. Contrast | Great Britain Automatic; adapted based on vehicle Day / Night | USA lighting. 666 Ign. logic Always day design; black or coloured text on light background. Always night design; white or coloured Setting units of measure Adjusting contrast 3 text on dark background. You can select which units of measure are (graphical information display) to be used. Select menu item Contrast from the Selections are indicated by a o in front of the menu item. Select menu item Units from the Settings Settings menu. menu. The menu for Contrast is displayed. Ignition logic 3 See Infotainment system instruction The available units are displayed. Confirm the required setting. manual. Select the desired unit. Selections are indicated by a o in front of the menu item. 88 Instruments, controls
Ü Board Computer 19,5° 19:36 BC 1 All values
BC 2 Range 257 km 257.0 km Range Timer 111 Aver. Consump. 7.0 Ltr./100km Ø40km/h 33km Tyres Inst. Consumpt. Ltr./100km 31.0 Ltr. 7.6 888 Ltr./100km Ø 7.0 19,5° 19:36 OK
Graphical information display 3 or Range If the fuel in the tank will allow less than colour information display 3, Range is calculated from current fuel tank 50 km (30 miles) of travel, the warning trip computer 3 content and instantaneous consumption. "Range" appears on the display. The trip computers provide information on The display shows average values. If the fuel in the tank will allow less than driving data, which is continually recorded After refuelling, the vehicle updates the 30 km (20 miles) of travel, the warning and evaluated electronically. range automatically after a brief delay. "Refuel!" 3 appears on the display. The trip computer main page provides Acknowledge the menu item as described information on range, average on page 84. consumption and instantaneous consumption. Instantaneous consumption Display changes depending on speed; To display other trip computer data, press the BC button on the Infotainment Display in l/h below 13 km/h. system and select the trip computer menu Display in l/100 km above 13 km/h. in the display. Instruments, controls 89
Distance travelled Displays number of kilometres (miles) driven. The measurement can be restarted at any time - see "Resetting trip computer Ü Board Computer 19,5° 19:36 Ü Reset BC 1 19,5° 19:36 information". BC 1 All values All values Average speed BC 2 Display of average speed. 257.0 km 257.0 km The measurement can be restarted at any Timer 111 Ø40km/h Ø40km/h time - see "Resetting trip computer Tyres information". 31.0 Ltr. 31.0 Ltr. Stoppages in the journey with the ignition 888 Ø 7.0 Ltr./100km Ø 7.0 Ltr./100km off are not included in the calculations. Effective consumption Displays amount of fuel consumed. Resetting trip computer information The information of the two trip computers The measurement can be restarted at any The following trip computer information can be reset separately, making it possible time - see "Resetting trip computer can be reset (restart measurements): to evaluate data from different time information". z Distance travelled periods. Average consumption z Average speed Select the desired trip computer Display of average consumption. z Effective consumption information. The measurement can be restarted at any z Average consumption time - see "Resetting trip computer The value for the selected function will be information". Select BC 1 or BC 2 from the trip computer reset and recalculated. menu. 90 Instruments, controls
Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, Ü Reset BC 1 19,5° 19:36 the values stored in the trip computer will Ü Board Computer 19,5° 19:36 be lost. All values BC 1 BC 2 00:00:00 257.0 km Timer Ø40km/h Tyres Start
31.0 Ltr. Reset Ø 7.0 Ltr./100km Options
To reset all information of a trip computer, Stop watch select menu item All values. Select menu item Timer from the Board After resetting, "- - -" is displayed for the Computer menu. trip computer information selected. The The Timer menu is displayed. recalculated values are displayed after a To start, select menu item Start. brief delay. To reset, select menu item Reset. Instruments, controls 91
The desired stop watch display can be Check control 3 selected from the Options menu 3: In vehicles with tyre pressure monitoring Driving Time excl. Stops system 3, if tyre pressure is too low, the Ü Board Computer The time the vehicle is in motion is display indicates which tyre to check, e.g.: recorded. Stationary time is not included. BC 1 Tyre pressure Driving Time incl. Stops BC 2 check rear The time the vehicle is in motion is Timer right tyre recorded. The time the vehicle is stationary (value in bar) Tyres with the key in the ignition switch is Check tyre pressure at next opportunity included. using suitable gauge. Travel Time Tyre pressure monitoring system 3 – Measurement of the time from manual see page 144. activation via Start to manual deactivation Tyre pressure – see page 224. via Reset. Display of current tyre pressure 3 Select menu item Tyres from the Board In vehicles with tyre pressure monitoring 3 Computer menu. system , if there is a major loss of pressure in a tyre, the display indicates the tyre at The current pressure of each tyre is fault, e.g.: displayed. Attention! Further information – see page 144. Rear left tyre pressure loss (value in bar) Stop immediately and check tyre. Tyre pressure monitoring system 3 – see page 144. Tyre pressure – see page 224. 92 Instruments, controls
Warning buzzers While driving: z when operating the turn signals. z if driver’s or passenger’s seat belt 3 is not engaged when the seat is occupied and vehicle speed exceeds approx. 22 km/h (14 mph).
When the vehicle is parked and driver’s door is opened: z with exterior lamps switched on. z when the key is in the ignition switch. 6 Seat belt warning chimes - see pages 46, 72, Windscreen wipers Adjustable wiper interval driving hints - see page 127, To activate, move lever upwards. To set the wiping interval to a value save fuel, protect the environment - between 1 and 10 seconds: see page 129. J =Off Switch on ignition. $ =Timed interval wipe Push lever down from position J. % =Slow Wait the desired interval. & =Fast Set the lever to adjustable timed interval wiper position $. J Press lever down from position : The interval remains stored until the next single swipe. change or the ignition is switched off. Further information - see pages 198, 202, Switching the ignition on and moving the 205. lever to $ sets the interval to 3.5 seconds. In this mode, wiping frequency is also affected by vehicle speed. As vehicle speed increases, wiping will become more frequent. Instruments, controls 93
Automatic wiping with rain sensor 3 Windscreen and headlamp washer Tailgate wiper and washer systems To activate, move lever upwards to systems 3 Activate wipers and washer as follows: automatic wiping with rain sensor To activate, pull lever towards steering Wipers on = Push lever forwards position $. wheel. Washer fluid is sprayed onto the Wipers off = Pull lever back towards windscreen. If the lever is held longer, the The rain sensor detects the amount of steering wheel wipers operate for two cycles after the lever water on the windscreen and automatically Wash = Press and hold button regulates the windscreen wipers. has been released and once more after a 3 second delay 3. Washer fluid is sprayed on to tailgate The wipers operate for one cycle to check The headlamp washer system 3 can only window when the button on the end of the the system when the ignition switch is lever is pressed. When the button is turned to ACC. be operated when the headlamps are on. Washer fluid is sprayed onto the released, the washer will stop, but the To turn wipers off, move lever to position J. headlamps. The headlamp washer system wipers will continue to swipe for approx. 3cycles. Keep the rain sensor area clean by can only be operated again after a short activating the windscreen washer system. delay. If washer fluid level is low then this Further information - see pages 198, 199, delay is increased. 202, 205. Further information - see pages 198, 202, 205. On vehicles fitted with rain sensor 3, keep the sensor area clean by activating the windscreen washer system. Further information - see pages 199, 202, 205. 94 Lighting
Daytime running lamps 3 Lighting Come on automatically when engine is started. They will turn off when the parking lamps or dipped beam are on, or when the engine is stopped. Main beam, headlamp flash ...... 95 Follow the regulations of the country in Automatic dipped beam activation 3 95 which you are driving when using daytime Turn signal lamps ...... 95 running lamps and front fog lamps. Front fog lamps > ...... 96 Driving abroad - see page 100. Fog tail lamp r ...... 96 Reversing lamps...... 96 Lamps on reminder Centre high-mounted stop lamp...... 96 If the driver’s door is opened when the light switch is in position 8 or 9 and the Hazard warning lamps ...... 97 Exterior lamps ignition is off, a warning chime will sound. Headlamp range adjustment q...... 97 Turn light switch: If the lamps are then switched off and back Peripheral lighting ...... 98 7 =Off on again, the warning chime will not sound. Instrument illumination, information 8 = Parking lamps 3 display illumination...... 98 Wiper activated lighting 9 = Dipped beam or main With light switch in AUTO position, Interior courtesy lamps...... 98 beam if windscreen wipers are operated for Battery discharge protection...... 100 AUTO = Automatic dipped beam 8 cycles or more, the exterior lamps Headlamps when driving abroad ..... 100 activation 3 illuminate automatically. In positions 8 and 9, the tail lamps, Approach lighting 3 license plate lamps and instrument panel Depending upon outside light conditions, lamps are also on. when you press q on the remote control, the hazard warning lamps flash twice and the exterior lamps illuminate for approx. 20 seconds. Lighting 95
Main beam, headlamp flash Automatic dipped beam Turn signal lamps To switch from dipped beam to main activation 3 To activate, press lever up or down lightly. beam, push lever forwards. Light switch to AUTO; dipped beam comes Lever up = Right turn To switch back to dipped beam, pull lever on automatically when the engine is Lever down = Left turn back towards steering wheel. running, depending on outside light conditions. When the steering wheel is turned back, the To activate the headlamp flash, pull lever lever automatically returns to its rest For reasons of safety, the light switch towards steering wheel. Main beam is position. This will not happen when making should always remain in the AUTO engaged for the duration of activation. a minor steering manoeuvre such as lane position. The blue control indicator P is illuminated changing. To ensure automatic dipped beam when main beam or headlamp flash is on. Tap signal: briefly move lever to resistance activation functions properly, do not cover point. The turn signal then flashes three the light sensor on top of the instrument times when changing lanes or the like. panel. Hold the lever if you want the turn signals to flash for longer. When released, the lever will spring back to rest position. The volume of the turn signal lamps’ audible warning is dependent upon vehicle speed. 96 Lighting
Reversing lamps Come on when reverse gear is engaged and ignition is switched on. Centre high-mounted stop lamp Comes on when the brakes are applied, acting as a third stop lamp, to supplement the brake lamps.
Front fog lamps > Fog tail lamp r On = Press button >, > On = Press button r, r illuminates in instrument illuminates in instrument panel. panel. Off = Press button > again, > Off = Press button r again, r extinguishes in instrument extinguishes in instrument panel. panel. The front fog lamps can only be switched The fog tail lamp can only be switched on on when both the ignition and headlamps when the ignition is on and the light switch are on. is in position 9, or the front fog lamps are 8 With automatic dipped beam activation 3, on and the light switch is in position . parking lamps and dipped beam come on With automatic dipped beam activation 3, simultaneously when the front fog lamps parking lamps and dipped beam come on are switched on. simultaneously when the fog tail lamp is Follow the regulations of the country in switched on. which you are driving when using front fog lamps. Lighting 97
Vehicles with level control system z Front seats occupied = 0 z All seats occupied = 1 z All seats occupied and load in =1 luggage compartment z Driver’s seat occupied and load =2 in luggage compartment Automatic headlamp range adjustment 3 On vehicles with Xenon headlamps, the range of the headlamps is adjusted automatically based on vehicle load. Hazard warning lamps Headlamp range adjustment q If control indicator q for automatic headlamp range adjustment illuminates in ¨ 3 To switch on, press button . Manual headlamp range adjustment the instrument panel while driving, a fault To switch off, press button ¨ again. With dipped beam switched on, adjust has occurred. headlamp range to suit vehicle load. To aid location of the pushbutton, the red Have the cause of the fault remedied surface is illuminated when the ignition is Correct adjustment of the headlamp range immediately. Consult a workshop. switched on. When the button is pressed, reduces dazzle for other road users. its control indicator flashes in unison with Automatic level control system 3 - the hazard warning lamps. see page 143. Vehicles without level control system z Front seats occupied = 0 z All seats occupied = 1 z All seats occupied and load in =2 luggage compartment z Driver’s seat occupied and load =3 in luggage compartment 98 Lighting
Peripheral lighting Instrument illumination, Interior courtesy lamps The dipped beam and reversing lamps information display illumination Front reading lamps, rear interior lamps illuminate for approx. 30 seconds after the Comes on when ignition is switched on. and luggage compartment lamps function driver exits the vehicle and closes the door. as courtesy lighting and illuminate when Brightness can be adjusted when the the doors or tailgate are opened. To activate function: exterior lamps are on: turn wheel to the 1. Switch off ignition. right or left until the desired brightness is If doors or tailgate remain opened, the lamps stay illuminated for approx. 2. Remove ignition key. obtained. 10 minutes. 3. Open driver’s door. If driver’s door is opened or q is pressed on 4. Pull turn signal lever towards the remote control, instrument panel lamps Once all doors and the tailgate are closed, steering wheel. will illuminate automatically and stay on the courtesy lamps dim gradually after for approx. 30 seconds until ignition switch approx. 10 seconds. If the driver’s door is left open, the lamps is turned to the ACC position. d will extinguish after two minutes. By pressing button , both front reading Display mode 3 - see page 87. lamps and the rear interior lamps Peripheral lighting can be deactivated by illuminate. inserting the key in the ignition switch or by pulling the turn signal lever towards the Press the button again to turn the lamps steering wheel again while the driver’s door off. is open. Lighting 99
Courtesy lamps can be turned off Front reading lamps Rear interior lamps immediately by pressing button K. Left and right reading lamps are Press button to turn on left and right rear individually operable. With ignition on: interior lamps individually. On = Press button L or M Press button again to turn the lamp off. Off = Press button again
9 Warning
Avoid using interior lamps while driving in the dark, as they can reduce driver visibility. 100 Lighting
Front door lamps Battery discharge protection Come on when a door is opened. To prevent battery from becoming Once all doors are closed, the front door discharged, the external lamps turn off lamps extinguish after approx. 10 seconds. automatically approx. 10 minutes after the If the doors are left open, the lamps will ignition is switched off. stay on for approx. 10 minutes. Battery discharge protection will not work if Front door lamps can also be turned off the lamps are turned on 10 minutes after immediately by pressing button K in the the ignition has been switched off; the key roof lining. cannot be removed from the ignition switch until the battery is recharged. Ignition switch illumination Comes on when you open a door. Headlamps when driving abroad Ignition switch illumination can also be The asymmetrical dipped beam increases the field of vision on the near side of the Luggage compartment lamps turned off immediately by pressing K lane. Come on when a door or the tailgate is button in the roof lining. opened. When driving in countries which drive on Sun visor lamps 3 the opposite side of the road, this causes Come on when vanity mirror covers are glare for oncoming traffic. opened. See page 34. For temporary periods, to avoid glare the Ashtray illumination headlamp pattern should be adjusted The portable front ashtray, located in the down to the horizontal position. front drink holder, illuminates depending Have the headlamps adjusted by a on outside light conditions. See page 68. workshop. Glove compartment illumination Comes on when the glove compartment is opened. See page 64. Infotainment system 101 Infotainment system Radio reception 3 The radio is operated as described in the operating instructions supplied. Vehicle radio reception will differ from that obtained with domestic radios. Radio reception 3...... 101 As the vehicle antenna is relatively near the Steering wheel mounted remote ground, the broadcasting companies control...... 101 cannot guarantee the same quality of reception as is obtained with a domestic Mobile telephones and radio radio using an overhead antenna. equipment (CB) 3 ...... 102 z Infotainment and navigation Changes in distance from the transmitter z systems 3...... 102 multi-path reception due to reflection and z shadowing Steering wheel mounted remote may cause hissing, noise, distortion or loss control of reception altogether. Infotainment system functions can be operated by the buttons mounted on the steering wheel. Further information - see pages 79, 84 and the relevant operating instructions. 102 Infotainment system
Mobile telephones and radio Obtain advice on predetermined equipment (CB) 3 installation locations for the external 9 Warning The Opel installation instructions and the antenna and equipment holder and ways of using devices with transmission power of When used in the vehicle interior, mobile operating guidelines provided by the telephones and radio equipment (CB) telephone manufacturer must be observed more than 10 Watts. We recommend that you consult your Opel Partner, who will with integrated antenna may cause when fitting and operating a mobile malfunctions in the vehicle electronics. telephone. Failure to do so could invalidate have brackets and various installation kits the vehicle’s operating permit (EU Directive and install them in accordance with Mobile telephones and radio equipment 95/54/EG). regulations. (CB) should only be used with an antenna fitted on the vehicle exterior. Requirements to ensure trouble-free Operation of a handsfree attachment with operation: no outside antenna, using the mobile telephone standards GSM 900/1800/1900 z Infotainment and navigation Professionally installed exterior antenna, and UMTS, may take place only if the 3 to obtain the maximum range possible maximum transmission power of the systems The systems are operated as described in z Maximum transmission power 10 W. mobile telephone does not exceed 2 W, in the case of GSM 900, and otherwise 1 W. the instruction manuals supplied. z Installation of the telephone in a suitable The operating instructions of the The navigation system is supplied with a spot (front centre console). manufacturer of the telephone and CD or DVD detailing the local territory. See important notes on page 57. handsfree attachment must be noted in all For additional countries/territories, cases. separate CD’s are available from your Opel For reasons of safety, we recommend that Partner. you do not use the phone while driving. Even use of a handsfree set can be a distraction while driving. Be sure to observe any country-specific regulations. Climate control 103 Climate control
Heating and ventilation system, air conditioning system ...... 103 Electronic Climate Control (ECC) 3 ... 103 Air vents ...... 104 Heated rear window, heated exterior mirrors 3 ...... 105 Heated front seats 3...... 105 Glove compartment cooling 3 ...... 105 Heating and ventilation system, Electronic Climate Control (ECC) 3 Heating and ventilation system ...... 106 air conditioning system Provides the greatest amount of comfort in Air recirculation mode...... 109 Ventilation, heating and cooling are the vehicle interior, regardless of the Air conditioning system...... 109 combined into one unit that is designed to weather, outside temperature or season. Electronic Climate Control (ECC) 3 ... 111 provide comfort regardless of the season, To ensure a constant and comfortable Air intake ...... 114 weather or outside temperature. climate in the vehicle, the temperature of Pollen filter ...... 114 When cooling is activated, the air is cooled inflowing air, the air flow rate, air distribution mode, air recirculation mode Note ...... 114 and dehumidified (dried). and air conditioning are automatically The heating unit heats the air as required in Maintenance ...... 114 adapted based on the climate conditions all operating modes, depending on the outside the vehicle and the current position of the temperature rotary knob. temperature of the vehicle interior. The air supply can be adjusted to suit personal requirements by means of the Electronic Climate Control (ECC) 3 - fan. see page 111. Air conditioning system - see page 109. 104 Climate control
Door window defroster vents Air distribution rotary knob set to l or J; cooled or heated air will be directed onto the windscreen and onto the door windows (mainly in the area of the exterior mirrors).
Rear air vents Operational when air distribution rotary knob is set to L, K or J. Cooled or heated air is directed into the footwell area of the rear passenger compartment. Keep the area underneath the front seats clear, to allow air flow to the rear Air vents Side air vents passenger compartment. Pleasant ventilation to the head area with To open and close air vents, turn horizontal unheated or slightly warmed air depending knurled wheel to the left or right. Additional air vents on the position of the temperature rotary Open air vents when air distribution rotary Below the windscreen (defroster vents) and knob. knob is set to M or L. in the front footwells. Centre air vents Depending upon the position of the To open and close air vents, turn horizontal temperature rotary knob, cold or heated knurled wheel to the left or right. air will be directed into the vehicle via these Open air vents when air distribution rotary air vents. knob is set to M or L. The air supply is increased by switching on The air supply is increased by switching on the fan. the fan. The air flow can be directed as desired by The air flow can be directed as desired by tilting and swivelling the slats up, down tilting and swivelling the slats up, down and sideways. and sideways. Climate control 105
Heated rear window, Heated front seats 3 Glove compartment cooling 3 heated exterior mirrors 3 Operational only in ignition switch Cooled air is fed into the glove Operational only in ignition switch positions ACC or ON. compartment through an air opening, positions ACC or ON. Press switch ß on respective side one or when the air conditioning is turned on. Press button Ü =On more times to set the desired heat output. Rotate adjustment wheel anti-clockwise to Control indicator in switch indicates which allow the air conditioning to keep the Ü Press button again = Off of the three heating levels is active. contents of the glove compartment cool. Control indicator in button. To switch heating off, set heat output to Rotate adjustment wheel clockwise to close Turn off as soon as vision is clear. the lowest level and press the switch again. air opening when glove compartment Rear window and exterior mirror heating is The control indicator will extinguish. cooling is not required. switched off automatically after approx. Prolonged use could cause damage to General notes and notes on air intake, 15 minutes. delicate and thin clothing and burn seat pollen filter and maintenance occupants. To avoid discharging the battery, do not see page 114. operate when you are just starting the Avoid subjecting seats to heavy impacts, vehicle, or if there is a build up of snow or as this may cause damage to the heating ice. Operate only with the engine running. element. Do not use sharp instruments or abrasive If temperature continues to rise, turn seat cleaners on rear window or exterior mirrors, heating off and consult a workshop. and avoid scratching or damaging their heating elements. 106 Climate control
Heating and ventilation system Central rotary knob: Temperature Right-hand rotary knob: Air flow Left-hand rotary knob: Air distribution To red = Warm Four fan speeds: M To head area via adjustable air vents To blue = Cold x =Off 4 = Maximum air flow L To head area via adjustable air vents and to footwell The rate of air flow is determined by the fan. The fan should therefore be switched K To footwell on during driving.
J To windscreen, front door windows and footwell l To windscreen, front door windows and head area via adjustable air vents Climate control 107
Heating To obtain a temperature for a "cool head The amount of heat is dependent on the and warm feet" effect: engine temperature and is thus not fully z Turn air recirculation mode 4 off. attained until the engine is warm. z Set the air distribution rotary knob to L. For rapid warming of the passenger’s compartment: z Turn temperature rotary knob to the middle. z Activate air recirculation mode 4. z Set fan to desired speed. z Set the air distribution rotary knob to K or L. z Open adjustable centre and side air vents. z Turn temperature rotary knob to red area for warm air. The comfort and general wellbeing of vehicle occupants are to a large extent z Set fan to 4. dependent on a suitable ventilation and Ventilation z Open adjustable side air vents. heating setting. z 4 Turn air recirculation mode off. Do not use this setting for extended z For maximum ventilation to head area: periods, as gradual deterioration in air set air distribution rotary knob to M. quality and an increase in humidity may cause windows to mist up. z For ventilation to footwell: set air distribution rotary knob to K. z For simultaneous ventilation to head area and footwell: set air distribution rotary knob to L. z Turn temperature rotary knob to blue area for cooling. z Set fan to desired speed. z Open adjustable centre and side air vents. 108 Climate control
z Set fan to 4. z Close centre air vents. z Open adjustable side air vents and direct them towards door windows. z Switch on heated rear window Ü. For simultaneous warming of the footwell, set air distribution rotary knob to J. Air conditioning n and air recirculation 4 are turned on automatically to improve defrosting efficiency when position J or l is selected. To prevent windows from misting up, do Heating the footwell Window demisting and defrosting not set air distribution rotary knob to z Set air distribution rotary knob to K. position J or l in extremely humid weather when temperature rotary knob is z Turn temperature rotary knob to red 9 Warning set to blue area for cooling. area for warm air. Failure to follow these instructions could z Switch on fan. lead to misted or icy windows and accidents stemming from impaired visibility.
To clear misted or icy windows, e.g. due to damp weather, damp clothing or low outside temperatures: z Set air distribution rotary knob to l. z Turn temperature rotary knob to red area for warm air. Climate control 109
Air recirculation mode should only be used for brief periods, due to gradual deterioration in air quality and an increase in humidity, causing windows to mist up. Driving with air recirculation mode on for extended periods may cause vehicle occupants to feel drowsy. Press button 4 again to turn air recirculation mode off; control indicator in the button extinguishes and outside air is drawn into the vehicle.
Air recirculation mode Air conditioning system During ’normal’ operation, the heating, As a supplement to the heating and ventilation and air conditioning system ventilation system, the air conditioning uses outside air. To prevent fumes or system cools and dehumidifies (dries) unpleasant odours from entering the inflowing air and removes dust and pollen, vehicle when in stationary traffic and when to provide maximum comfort under any rapid heating or cooling of the passenger weather conditions. 4 compartment is required, press button ; If cooling or dehumidification is not control indicator in the button illuminates required, switch off cooling in order to save and air is recirculated. fuel. 110 Climate control
Once activated, the air conditioning system is operated via the normal heating and ventilation controls. Even with air conditioning on, if temperature rotary knob is set to warm, the vehicle will still produce warm air in the passenger compartment. To improve efficiency of the air conditioning, always close the windows, to prevent chilled air from escaping. Switching on the air conditioning will assist in windscreen demisting. In very hot temperatures, before starting the engine, Cooling allow hot air to escape from the vehicle by Normal cooling Operational only with engine running and opening the windows and sun roof 3. z Press button n with the fan switched on: When the air conditioning system is (to switch on air conditioning system). switched on, at least one of the adjustable Press button n =On z Turn air recirculation mode 4 off. centre or side air vents must be open, so Press button n again = Off that the evaporator does not ice up due to z Set air distribution rotary knob to position M or L. Control indicator in the button illuminates lack of air movement. when air conditioning is enabled and Driving in stop-and-go traffic may reduce z Turn temperature rotary knob to blue extinguishes when the system is switched the effectiveness of the air conditioning area for cooling. off. system. z Set fan to desired speed. Cooling switches off automatically at low Using the air conditioning system when z Open air vents as required. outside temperatures. driving up long hills or in heavy traffic Engine power and performance may be can cause engine overheating. If engine affected when the system is on. coolant temperature warning control indicator W illuminates in instrument If the fan is switched off, the air panel, turn off air conditioning and allow conditioning system will not operate. engine to idle for a few minutes (see page 71). Climate control 111
Electronic Climate Control (ECC) 3 Provides the greatest amount of comfort in the vehicle interior, regardless of the weather, outside temperature or season. To ensure a constant and comfortable climate in the vehicle, the temperature of the inflowing air, the air flow rate, air distribution mode, air recirculation mode and air conditioning are automatically adapted based on the climate conditions outside the vehicle and the current temperature of the vehicle interior. Temperature changes due to external influences, such as direct sunlight, are Maximum cooling automatically compensated. When cooling (air conditioning Open windows and sun roof 3 briefly so compressor) is active, air is cooled and that warm air can escape rapidly. dehumidified. z Press button n The pollen filter removes dust, soot, pollen (to switch on air conditioning system). and spores from the inflowing outside air. z Activate air recirculation mode 4. z Set air distribution rotary knob to M. z Turn temperature rotary knob all the way to blue area for cooling. z Set fan to 4. z Open all air vents. 112 Climate control
Temperature preset The central rotary knob can be used to set the temperature; 22 °C, 24 °C and 26 °C appear on the rotary knob. Intermediate settings are possible. The selected temperature is maintained. At the lowest or highest temperature setting, the system works at maximum cooling or heating.
Automatic air recirculation Automatic mode The automatic air recirculation system has Basic setting for maximum comfort: an air quality sensor to detect harmful z Press AUTO button. ambient gases, in which case it will switch automatically to air recirculation mode. z Open all air vents. Press automatic air recirculation button t; z Set temperature using central rotary the system provides the optimum settings knob. for almost all conditions. Control indicator All air vents are actuated automatically in in the button illuminates when automatic automatic mode. The air vents should air recirculation is enabled. therefore always be open - see page 104. Press button t again to turn automatic air The control indicator in the AUTO button recirculation system off; control indicator in illuminates when automatic mode has the button extinguishes and outside air is been selected. drawn into the vehicle. To switch the system off, set fan to x. The system is only operational when the engine is running. Climate control 113
Air recirculation mode 4 is automatically switched off. Air conditioning n switches on. To switch off window demisting and defrosting, press button V again, press AUTO button, adjust fan speed or air distribution rotary knob.
Manual settings Window demisting and defrosting Under certain circumstances (e.g. iced or misted windows), the functions of the 9 Warning system can be modified manually. System settings can be changed by Failure to follow these instructions could pressing button n (control indicator in lead to misted or icy windows and button will illuminate) or by adjusting the accidents stemming from impaired fan or air distribution rotary knob. visibility. Automatic regulation of temperature, air flow rate, air distribution mode, air To clear misted or icy windows, e.g. due to recirculation mode and air conditioning is damp weather, damp clothing or low disabled. outside temperatures: To return to automatic mode: z Press button V, to clear the windscreen. press AUTO button. z Switch on heated rear window Ü. Air distribution mode - see page 106, z Set fan to desired speed. air flow rate - see page 106, air recirculation mode - see page 109, air conditioning system - see page 109. 114 Climate control
Note Maintenance If the windscreen mists up in damp To ensure continuously efficient weather, temporarily set the system as performance and prolong the life of the air described under "Window demisting and conditioning system, it must be switched on defrosting" - see pages 108, 113. for a few minutes once a week, irrespective Cooling is most efficient when the windows of the weather and time of year. are closed. If the interior is extremely hot Electronic Climate Control (ECC) 3 handles due to a long period in strong sunlight, this automatically while driving. Air briefly open the windows and sun roof 3 to conditioning compressor operation is not allow hot air to escape quickly. possible at low outside temperatures. When cooling (air conditioning Malfunctions in the system must not be compressor) is switched on, condensation rectified by the owner: consult a workshop. forms, which is expelled from the underside Air intake of the vehicle. The air intakes in front of the windscreen in When cooling is switched on, at least one of the engine compartment must be kept the adjustable centre or side air vents must clear to allow air intake. Remove any be open so that the evaporator does not leaves, dirt or snow. ice up due to lack of air movement. Cooling switches off automatically at low Pollen filter outside temperatures. The pollen filter cleans dust, soot, pollen Do not cover the interior temperature and spores from the air entering from sensor (located below the fan switch) or the outside. The active carbon layer 3 sunlight sensor (located in front of eliminates most odours and harmful windscreen defroster vents) as this could ambient gases from the air. cause the Electronic Climate Control (ECC) Replace the pollen filter at the intervals system 3 to malfunction. given on pages 206 to 212. Driving and operation 115 Driving and operation Automatic transmission 3 The automatic transmission permits 9 Warning manual gearshifting (manual mode) or automatic gearshifting (automatic mode) Disregard of these instructions may with fully automatic clutch control. cause damage to the vehicle and lead to The engine can only be started when the injuries or endanger life. 3 Automatic transmission ...... 115 selector lever is in position P or N. When All Wheel Drive...... 121 starting in P, turn key in ignition switch to Selecting D puts the transmission in Driving hints ...... 127 ACC or ON, depress foot brake and press automatic mode. Save fuel, protect the environment... 129 selector lever button before selecting a If the selector lever is moved to the left from Fuels, refuelling...... 131 gear. position D, manual mode is activated. Catalytic converter, exhaust Do not accelerate whilst gearshifting. If a Forward gear changes only can then be emissions...... 133 gear has been selected and the foot brake made manually by tipping the selector Drive control systems ...... 136 is released without accelerating, the lever towards + or -. vehicle will "creep". Brake system...... 145 Anti-lock Brake System (ABS) u...... 148 Never operate the brake pedal and accelerator simultaneously. Wheels, tyres ...... 149 Roof racks 3...... 153 Flex-Fix system 3...... 154 Towing equipment 3...... 164 Towing...... 167 116 Driving and operation
Selector lever can only be moved out of P or N with the ignition switched on and the foot brake depressed (selector lever lock). To engage P or R, press selector lever button. Never shift to P or R while the vehicle is moving. The engine can only be started when the selector lever is in position P or N. Depress foot brake or apply hand brake before starting. Do not accelerate during the selection procedure. Transmission display Selector lever settings, Display of mode or current gear. P, R, N and D (automatic mode) P P Park position. Park position. Front wheels locked. Only engage when the vehicle is R Reverse gear. stationary and the hand brake is applied. "P" appears on the N Neutral. transmission display.
D Automatic mode. R Reverse gear. Only engage when the vehicle is stationary. "R" appears on 1 to 5 Selected gear in manual the transmission display. mode. N Neutral or idle. "N" appears on the transmission display.
D Drive position for normal driving in 1st gear to 5th gear. "D" appears on the transmission display. Driving and operation 117
When upshifting in manual mode, take heed of prevailing road conditions, keeping engine speed below the red zone. Downshifts must be made in accordance with vehicle speed. Gears can be skipped by moving the selector lever repeatedly at short intervals. When starting on slippery surfaces, move selector lever forwards to engage 2nd gear. The selected gear is displayed in the transmission display. For safety reasons, kickdown is also Manual mode Winter program available in manual mode - see page 118. Move selector lever out of position D (to the In the event of difficulties starting-off on icy left) into manual gate, then forwards or To move back to D, push selector lever and slippery surfaces, press button n; backwards. back to the right. control indicator 0 is illuminated in the < Shift to a higher gear. instrument panel and the vehicle sets off in 3rd gear, to reduce slipping and loss of ] Shift to a lower gear. traction. Tip selector lever in the appropriate Winter program is switched off by: direction. It then returns to centre position. z pressing button n again Gearshifting in manual mode can be (control indicator 0 will extinguish in achieved whilst accelerating. instrument panel), If the engine speed is too low, the z turning off the ignition. transmission will automatically shift to a If the vehicle is switched to manual mode lower gear, even in manual mode. This while Winter program is active, the Winter prevents the engine from stalling. program is switched off. After stopping, 1st gear is automatically selected. No automatic shifting to a higher gear takes place at high engine speeds. 118 Driving and operation
Engine braking assistance Stopping the vehicle Automatic mode The selector lever can be left in the current The automatic transmission automatically drive range when the engine is running. selects the driving programs with the best In automatic or manual mode, once the possible braking effect. vehicle is stationary, first gear engages If necessary, lower gears can also be automatically and the clutch opens. selected in manual mode to increase the In position R, reverse remains engaged. braking effect. 1st gear has the greatest braking effect. When stopping on gradients, engage hand brake or depress brake pedal. Do not Manual mode hold the vehicle in place with the In order to utilize the engine braking effect accelerator. when driving downhill, select drive range 3, 2 or, if necessary, 1 in good time. Switch off engine if stopping for a lengthy period, e.g. in traffic jams. Kickdown The braking action is most effective in drive Depress accelerator pedal past the range 1. If drive range 1 is selected at too pressure point and hold in position; high a speed, the transmission remains in below certain speeds, the transmission the current gear until the shift point for shifts down into a lower gear. Full engine drive range 1 is reached, e.g. as a result of power is available for acceleration. deceleration. When the desired speed is reached, ease Use of the engine braking effect, as off the accelerator; the transmission shifts opposed to the use of the foot brake when up into a higher gear. driving downhill, can extend the life of the brakes. For safety reasons, kickdown is available in both automatic and manual mode. Driving and operation 119
Parking Rocking the vehicle Before leaving the vehicle: If it becomes necessary to rock the vehicle z Depress and hold foot brake, to free it from water, ice, sand, mud, snow z Apply hand brake, or a dip, observe the following: z Move selector lever to position P, Check there are no objects or people in the z Turn key to LOCK position, vicinity before attempting to rock the z Remove ignition key, vehicle. z Engage steering column lock, Turn the steering wheel fully from left to z Lock the vehicle. right to clear the area around the front When the ignition is switched off, the tyres. automatic transmission no longer responds Move the selector lever between R and a to movements of the selector lever. forward gear in a repeat pattern while applying light pressure to the accelerator pedal when the vehicle is in gear. Manoeuvring the vehicle Do not spin the wheels or race the engine To manoeuvre the vehicle back and forth and avoid sudden acceleration. during attempts to park or in garage entrances, the creeping movement can be This applies only in the exceptional utilized by releasing the foot brake. circumstances mentioned above. Never actuate the accelerator and brake If the vehicle cannot be released after pedals simultaneously. rocking the vehicle several times, your vehicle may need to be towed. Towing - see page 174. 120 Driving and operation
If the cause of the interruption to the power supply is not a discharged battery, release selector lever: 1. Turn off ignition and remove key. 2. Depress and hold foot brake. 3. Remove cap on console with a suitable screwdriver. 4. Insert ignition key and press gently into shift lock release slot. 5. Shift to neutral (N). 6. Remove key from shift lock release slot. 7. Start engine and shift to chosen gear. 8. Reinstall cap on console. Fault Z Interruption of power supply Have cause of power supply interruption If a fault occurs in the automatic The clutch is not disengaged if the vehicle remedied immediately. Consult a transmission, control indicator Z will battery is discharged and a gear has been workshop. illuminate in the instrument panel. selected. The vehicle cannot move. Automatic shifting may be much harsher If the battery is flat, the selector lever than normal or, in the case of a serious cannot be moved out of position P or N. fault, cancelled altogether. Start the vehicle using jump leads - Consult a workshop as soon as possible to see page 172. have the cause of the fault eliminated. Driving and operation 121
All Wheel Drive On-road driving All Wheel Drive (AWD) is an active-on- The increased traction of All Wheel Drive demand system that engages vehicles offers greater driving control in automatically, with no action required by adverse road conditions, particularly the driver. Depending on the driving heavy snow and ice. However, All Wheel environment, the vehicle switches between Drive vehicles are not "skid-proof" and do two-wheel drive and four-wheel drive, to not decrease stopping distances. give the vehicle more traction and stability All Wheel Drive vehicles have a higher when necessary. centre of gravity than conventional If the front wheels begin to slip, the rear vehicles. Always approach curves at an wheels will automatically begin to drive the appropriate driving speed. Do not attempt vehicle as required. to go as fast through turns as you might in a conventional vehicle. More torque is transferred to the wheels Strong crosswinds can affect the normal that have the most traction, so the vehicle All Wheel Drive control indicator has optimum grip at all times. steering of the vehicle. Drive slower under When the ignition is switched on, strong crosswind conditions. There may be a slight engagement noise control indicator B illuminates for approx. during hard use. 4 seconds. The system is ready for As well as enabling the vehicle to be driven operation when the control indicator off-road, this system also enables the extinguishes. vehicle to be driven on normal roads If the control indicator flashes during without incurring excessive tyre and driving, All Wheel Drive is temporarily drivetrain wear or causing poor control. disabled. If it flashes briefly then extinguishes, this is normal and does not indicate a fault. If the control indicator flashes continuously, there is a fault in the system. Consult a workshop as soon as possible. 122 Driving and operation
Always exercise caution when in slippery Off-road driving Preparation conditions (caused by sand, gravel, water, During off-road driving, you will encounter The duration, distance and conditions of snow or ice on the road), in order to a variety of driving conditions and the off-road activity determine the extent maintain vehicle control. circumstances too numerous to list here. of the preparation that is required. The Use the accelerator to control the vehicle - Always use good judgement and common following are given as guidelines. keep brake pedal use to a minimum. sense. If you feel uncomfortable about Know the area where you will be driving, z Do not slip the clutch. tackling a given situation, do not attempt either by inspection or from terrain maps. it. Decide your route in advance and ensure z Do not spin the wheels. 1) Avoid protruding objects (such as rocks or that it is a vehicular right of way . z Do not make exaggerated or jerky tree stumps) that may damage the Make a thorough check of the vehicle. steering movements. underbody and tyres of your vehicle. Check the following: Driving a vehicle in snow and ice should be Test the brakes after operating in mud, to z undertaken with extreme caution: Oil, water, fuel, brake and clutch fluid clear excess mud from the braking levels, z Select a gear suitable for the conditions. surfaces. z Drive belts, z Windscreen wipers and washer system, z Start the vehicle moving with minimal Gripping the steering wheel z Lamps. engine revs, low gear and combined Terrain conditions can cause rapid and clutch and accelerator control. unexpected movement in the steering, Maintenance - see pages 126, 206. z Change to a higher gear as quickly as especially rough terrain. possible, to keep the engine revs low. 9 Warning z With automatic transmission 3, select drive range D and press button n, to Be ready to deal with these movements activate the Winter program. by having a firm grip on the outer rim of the steering wheel with the thumbs outside the spokes, to guard against injury from kickback.
1) Observe national regulations. Driving and operation 123
Check the jack and wheel changing tools, and include a board or plate for supporting the jack on soft ground. Carry emergency equipment, i.e. tow rope, spade, first aid kit etc., which may be desirable if you intend entering unfamiliar off-road terrain. A tow rope should be carried, to allow the recovery vehicle to be placed clear of any adverse ground. Your Opel Partner will assist you in assessing any special requirements.
Ensure that tyres (including the spare) are Secure all loose items and luggage that inflated to the correct pressure and are may cause injury if thrown around the suitable for the prevailing off-road passenger compartment in bumpy conditions. conditions. Avoid carrying heavy loads on Tyre pressures - see page 224. the roof. Make sure all doors, the tailgate and the bonnet are firmly closed. Securing items using lashing eyes - see page 61. 124 Driving and operation
The ground clearance, ramp angle, angle Driving through water Avoid water entering the air intake system. of approach and departure and wading Do not exceed the maximum wading depth need to be considered, especially in depth. 9 Warning hilly conditions and when wading, to Check the depth of water: choose the If water enters the air intake system, prevent the vehicle becoming stuck and lowest entry and departure angles before engine seizure with severe costly damage possibly damaged. entering. may result. Technical data - see page 215. Maintain a steady engine speed, to help prevent water from entering the exhaust system, but do not exceed 5 km/h (3 mph), Test the brakes after leaving the water - to avoid splashing the water. wet brakes are less effective than dry ones. Drive with the flow wherever possible, not Perform the service operations for wading, against it. If you have to drive against the involving checks for water contamination, flow, try to drive at an angle to it, so that at the earliest opportunity. the leading corner of the vehicle will help Service checks after wading - deflect water from the engine see page 126. compartment. Avoid splashing the water - if the ignition system becomes wet, the engine may stall. Driving and operation 125
Self-help Cleaning Clean and check the mechanical parts of Recovery and towing Clean the vehicle thoroughly and as soon the vehicle, particularly the following When recovering or towing a vehicle as possible after driving off-road. areas: off-road, observe the following: Do not let mud remain dry on any part of z Driveshafts, including sealing bellows, z A greater force is required to move a the vehicle as it becomes abrasive and can z Front brake calipers, pads and discs, vehicle from or through mud than when damage paint, glass, seals, bearings and z Front suspension, on a hard surfaced road. brake components. z Clutch fork sealing bellows, z z Attach a tow rope to the towing eye of If left to build up, mud can seriously affect Rear brake calipers, pads and discs, z the vehicle, not to the axle - the air flow through and over mechanical Rear suspension, z see pages 164, 174. components and cause localised Fuel tank and underguard, z overheating and failure of parts, especially Breathers, axles and fuel tank, z Where possible, drive both vehicles z in the engine compartment. Load sensing valve, forward to affect a recovery, using an z Transfer box and underguard, appropriate gear to avoid wheelspin. Ensure the radiator core and the area z Engine oil pan and underguard. between the radiator and intercooler/oil z Avoid the use of reverse gear because of Observe the following: possible resultant wheelspin. cooler (where installed) is cleaned, to maintain proper cooling air flow. z Do not spray high-pressure water z Stay clear of the tow rope. Check the radiator and cooler cores for directly at the vehicle seals. 9 Warning blockage (sand, silt etc.). z The wheels must be removed to clean all Check the tyre treads. mud and stones from the brake calipers Breaking ropes can cause serious injury. and to check brake pad wear. z The areas on the upper side of the underguards must be cleared of stones, Wheel changing to prevent damage to the engine oil pan Place a board or plate beneath the jack, to and the fuel tank. prevent it from sinking into soft ground. Further information - see page 178. 126 Driving and operation
Maintenance All Wheel Drive summary Don’t Certain maintenance operations, e.g. Do z Do not venture off-road unless you are changes of engine oil, oil filter, air cleaner z Check fuel and tyres, water and oil levels certain that the conditions are capable element and brake pads, are required before venturing off-road. of being negotiated safely by you and more frequently for severe operating z Survey on foot before driving off-road, your vehicle. conditions, e.g. driving on unsurfaced especially when traversing hillsides, z Do not take unnecessary risks. roads, during thick dust or mud wading, driving in deep snow and over accumulation, etc. z Do not use the brakes excessively, to ridges. maintain steering control. If the vehicle is driven off-road to a great z Select the correct gear for the conditions. extent, the chassis will need regular z Do not change gear on difficult terrain - inspection. z Use the engine’s power of acceleration depressing the clutch may cause the and deceleration with the correct gear, vehicle to stop because of drag on the Your Opel Partner will inform you which to control the vehicle. wheels - or accelerate backwards or additional service is required between the forwards when on a hill. normal service intervals, after z Keep a firm grip on the outer rim of the consideration of the specific operating steering wheel - keep your thumbs away z Do not ride or slip the clutch. conditions of your vehicle. from the spokes. z Do not spin the wheels if stuck in mud, Further information - see page 206. z Drive carefully and be prepared for sand or snow - they will only dig in emergencies. deeper. Service checks after wading z Drive slower under crosswind conditions. z Do not drive at an excessive speed, After wading, check for the ingress of water especially into corners. Your All Wheel into the following: z Approach obstacles and conditions off-road at the correct angles and with Drive vehicle has a higher centre of z Brake fluid reservoir, sufficient momentum to negotiate the gravity than conventional vehicles. z Air cleaner element, obstacle, but do not put undue strain on Sudden changes of direction can lead to z Engine, the vehicle. loss of control. z Transmission, z Axles, z Use caution - if you are not sure, do not z Interior of vehicle. do it. Renew any lubricating oil or hydraulic fluid that has a milky appearance, indicating contamination with water. Driving and operation 127
Driving hints Brake servo unit Driving in extreme conditions The first 1000 km (600 miles) With the engine not running, the brake When driving in hazardous conditions, e.g. Drive your vehicle at various speeds. Do servo unit is no longer effective once the in snow, ice, mud, sand or water, drive not use full throttle. Never allow the engine brake pedal has been depressed once or slowly and cautiously to allow for greater to labour at low revs. twice. The braking effect is not reduced, braking distances. but substantially greater foot pressure is If stuck, use 2nd gear (automatic Make good use of all gears. Depress the necessary to stop the vehicle. accelerator pedal a maximum of around transmission in drive range 2) to avoid three quarters of the available pedal travel Power steering spinning the front wheels. in all gears and drive ranges. Never leave the steering wheel on full lock Use sand, tyre chains or other non-slip when the vehicle is stationary, as this may materials to provide traction when stuck in Do not drive faster than three quarters of damage the power steering pump. maximum speed. snow, mud or ice. If the power steering should fail - e.g. when Driving through water Avoid quick starts, sudden acceleration the vehicle is being towed with the engine and prolonged high-speed driving, to Before attempting to drive through water, switched off - the vehicle can still be check the depth. If the depth is slightly avoid engine damage and to conserve properly steered, but considerably greater fuel. lower than the underbody of your vehicle, effort is necessary. do not attempt to drive through it. Do not brake unnecessarily hard for the Driving in mountainous terrain or with a first 200 km (125 miles). Driving too quickly through water can caravan/trailer cause water to enter the engine through If possible, avoid towing another vehicle. Electrically driven fan; the fan cooling the air intake, causing severe damage. capacity is not dependent on engine Never coast with engine not running Drive slowly, in a high engine rpm in as low speed. It is not necessary, therefore, when a gear as possible. Many units may then not function (e.g. driving uphill to shift down into a lower brake servo unit, power steering, airbag gear if the vehicle can climb in a higher Driving with a roof load system). Driving in this manner is a danger gear. Do not exceed the permissible roof load - to yourself and others. see page 221. For safety reasons, distribute the load evenly and secure it tightly with straps so that it cannot slip. Set the tyre pressure to the value given for full load. Do not drive faster than 120 km/h (75 mph). Check and retighten straps at frequent intervals. 128 Driving and operation
Switching off the engine Engine rpm Clutch operation 3 If the engine temperature is very high, e.g. Under all driving conditions, drive in a Always depress the clutch pedal hard to after driving in mountainous terrain: allow favourable engine speed range. the floor, to prevent shifting difficulties and engine to idle for approx. 2 minutes, in Warming up transmission damage. There must be no order to prevent heat accumulation. Allow engine to warm up while driving. Do mats in the area of the pedals. When you switch off, fans in the engine not warm it up by letting it run at idling When driving, do not use the clutch pedal compartment may continue running for a speed. Do not apply full throttle until as a foot rest; this will cause substantial time, to cool the engine. engine reaches operating temperature. clutch wear. Vehicles with turbocharger 3 After a cold start, automatic Pedals In order to protect the turbocharger, after transmission 3 does not shift into higher Do not place any objects in the footwell running at high engine speeds or high gears until higher engine speeds have been which could slip under the pedals and engine loads, operate the engine briefly at reached. This allows the catalytic converter inhibit the pedal travel. a low load or run in neutral for approx. to quickly reach the temperature required To ensure the pedal travel is uninhibited, 30 seconds before switching off. for optimum pollutant reduction. there must be no mats in the area of the Save energy – more kilometres/miles Correct gear selection pedals. Please observe the running-in hints on the Do not race your engine whilst in neutral or When driving, do not use the brake pedal previous page and the tips for energy with a low gear selected. Driving too fast in as a foot rest; this will cause substantial saving on the following pages. individual gears or drive ranges as well as wear to brake components and cause Good, technically correct and economical stop-and-go traffic increase engine wear overheating, resulting in longer braking driving ensures maximum durability and and fuel consumption. distances. performance for your vehicle. Change down Battery care whilst driving Overrun When decreasing speed, shift down into When driving slowly or when the vehicle The fuel supply is automatically shut off the next lowest gear. Do not slip the clutch is stationary, e.g. in slow urban traffic, during overrun, e.g. when the vehicle is with a high-revving engine. This is stop-and-go traffic or traffic jams, turn off being driven down long gradients or during especially important when hill climbing. all unnecessary electrical loads where braking. To enable the overrun cut-off to possible (e.g. heated rear window, come into action, do not accelerate or auxiliary headlamps). declutch during overrun. When starting the engine, depress the clutch pedal so that transmission resistance is eliminated and the starter motor and battery are relieved. Driving and operation 129
Save fuel, protect the End-of-life vehicle recovery Warming up environment Information on end-of-life vehicle recovery z Full throttle and warming up at idle Trend-setting technology centres and the recycling of end-of-life speed increase wear, fuel consumption, When developing and manufacturing your vehicles is available at www.opel.com. fuel emission, the amount of pollutant in vehicle, Opel used environment-friendly Drive in an energy and the exhaust and the amount of noise. and, in the main, recyclable materials. The environment-conscious way z Drive off immediately after starting. production methods used to make your z High fuel consumption, noise levels and Warm up the engine by running it at vehicle are likewise environmentally- exhaust emissions are often caused by a moderate engine speeds. compatible. driving style that is not energy and Uniform speed Recycling of production wastes keeps the environment-conscious. z Hectic driving significantly increases fuel circulation of material closed. Reduction of z You should therefore drive with energy in consumption, the quantity of emission energy and water requirements also helps mind: "more kilometres/miles with less and the proportion of pollutant in the to conserve natural resources. fuel". exhaust. A highly advanced design means that your z Reduce the noise level and exhaust z Do not accelerate and brake vehicle can be easily disassembled at the emissions by adopting an environment- unnecessarily. Drive at uniform speed. end of its working life, and the individual conscious driving style. This is extremely Avoid frequent starting-off and materials separated for subsequent re-use. worthwhile and improves quality of life. stopping, e.g. at traffic lights, in short Materials such as asbestos and cadmium Fuel consumption depends to a great distance traffic and in queues of traffic, are not used. The refrigerant in the air extent on your own personal driving style. by means of clever planning. Select conditioning system is CFC-free. The following hints are intended to help roads with good traffic flow. New painting techniques employ water as you consume fuel at a rate that is as close Idling a solvent. as possible to the specified levels. z The engine also consumes fuel when Check your vehicle’s fuel consumption idling. every time you refuel. This facilitates early z If you have to wait for more than detection of any irregularities causing 1 minute, it is worthwhile switching off increased fuel consumption. the engine. Five minutes of idling corresponds to approx. one kilometre (0.6 miles) of driving. z Idling for more than 5 minutes can cause excessive temperatures and damage to the exhaust system. 130 Driving and operation
Overrun Tyre pressure Repair and maintenance z The fuel supply is automatically shut off z Inadequate tyre pressure, leading to z Improper repairs or adjustment and during overrun, e.g. when the vehicle is higher road resistance, costs money in maintenance work can increase fuel being driven down long gradients or two ways; for more fuel and increased consumption. Do not carry out work on during braking - see page 128. tyre wear. the engine yourself. z To enable the overrun cut-off to take z Regular checks (every 14 days) pay off. You may, out of ignorance, infringe effect and save fuel, do not accelerate or Electrical loads environmental laws by not disposing of declutch. z The power consumption of electrical materials properly. Correct gear selection equipment increases fuel consumption. Appropriate parts might not be recycled. z High revs increase engine wear and fuel z Switch off all additional consumers (e.g. Contact with some of the materials consumption. air conditioning, heated rear window) involved may pose a health hazard. z Do not race your engine. Avoid driving at when they are no longer required. z We recommend that repairs and high engine speeds. Roof racks 3 maintenance be entrusted to an Driving with an eye on the tachometer z Roof racks can increase fuel Opel Partner. saves fuel. If possible, drive at low revs in consumption by approx. 1 l/100 km Extreme driving conditions each gear and at a constant speed. (3.5 gal./1000 miles) due to air z Driving up steep gradients, cornering, Drive in top gear as much as possible, resistance. driving on poor roads, and winter driving shift up as soon as possible and do not z Remove them if they are not being used. all increase fuel consumption. shift down prematurely. Fuel consumption increases dramatically High speed in urban traffic and at winter z The faster the speed, the higher the fuel temperatures, especially on short trips consumption and noise level. Driving at when the engine operating temperature full throttle uses up a great deal of fuel is not reached. and generates excessive noise and high emission levels. z Follow the hints given above to keep fuel consumption to a minimum under such z Slightly releasing the accelerator pedal conditions. results in distinct fuel savings with no major loss of speed. Drive at no more than around three quarters of maximum speed and you will use up to 50% less fuel, without losing a great deal of time. Driving and operation 131
Fuels, refuelling Fuel for petrol engines Fuel for diesel engines Fuel consumption Commercially available high-quality fuels Diesel engines must be operated only on Optional equipment (e.g. wide tyres, are suitable (see page 217). Fuel quality commercially available diesel fuel meeting towing equipment) increases the kerb has a decisive influence on the power the specifications of DIN EN 590. weight and, in some cases, also the output, driveability and life of the engine. Marine diesel fuel, fuel oils, diesel fuels, permissible Gross Vehicle Weight. The additives contained in the fuel play an which are entirely or partially plant based important role in this regard. You should such as rape seed oil or bio-diesel, This in turn increases fuel consumption and therefore use only high-quality fuels reduces the maximum speed of the vehicle. Aquazole and similar diesel-water containing additives. emulsions must not be used. When the vehicle is new, there is increased Petrol with too low an octane number can friction between the engine and The flow and filterability of diesel fuels are cause pinking. Opel cannot be held liable insufficient at low temperatures, as a result transmission components lasting for for resulting damage. several thousand kilometres. This also of crystallized paraffins. increases fuel consumption. Petrol with a higher octane number can Diesel fuels with improved low- always be used. temperature properties are therefore A dispensing pump for leaded fuel cannot available on the market during the winter be inserted in the fuel tank of a vehicle that months. Make sure that you use winter fuel must be operated on unleaded fuel only. before the start of the cold weather Use of petrol with an octane rating of 95 season. will ensure economical driving Use of diesel fuels with manufacturer- guaranteed winter properties eliminates the need for additives. 132 Driving and operation
Fuel filler cap Correct refuelling is largely dependent on If replacing the fuel filler cap, be sure to use correct operation of the dispensing pump: the original fuel filler cap for your model, to z Insert dispensing pump as far as it will go ensure full functionality. and switch it on. Refuelling z After the first automatic cut-off, do not 9 Warning fill the tank any further. Replace the fuel filler cap and turn it Care must be taken when dealing with clockwise until you hear several clicks. fuel. Close tank flap. Before refuelling, it is absolutely vital to Wipe off any overflowing fuel immediately. switch off the engine and any heating systems with combustion chambers. If fuel is spilt onto the vehicle, rinse the area with clean, cold water as soon as possible, Switch off mobile phones. The fuel filler neck with bayonet cap is to avoid permanent damage to painted Fuel is inflammable and explosive, located on the left rear side of the vehicle. surfaces. therefore avoid dealing with fuel near The tank flap is locked together with the naked flames and doing anything that doors - see page 25. would generate sparks. No smoking! Unlock doors, tailgate and tank flap by This also applies where the smell of fuel is pressing button q on the remote control or noticeable. If the smell of fuel vapour by pressing central locking switch m in the occurs in the vehicle itself, have the cause driver’s door. remedied immediately by a workshop. Open the tank flap by hand. If, in cold weather, the tank flap does not Ensure suitable fuel is available before open, tap it and try again. driving in foreign countries. To unlock fuel filler cap: turn it anti- clockwise. If hissing occurs, wait until it stops before completely unscrewing the fuel filler cap. Remove fuel filler cap and place it in its holder on the inside of the tank flap. The fuel tank has a limiting system which prevents overfilling of the tank. Driving and operation 133
Damage to the catalytic converter or the Catalytic converter for diesel engines vehicle may result if the following points Damage to the catalytic converter or the are not observed: vehicle may result if the following points z If the engine misfires or runs roughly are not observed: after a cold start, the engine power has Consult a workshop as quickly as possible reduced significantly or other unusual in the event of irregular engine running, a operating problems occur that indicate significant loss of engine power or other a fault in the ignition system, please unusual malfunctions. If necessary, driving contact a workshop as quickly as may be continued for a short time at a low possible. Drive at a slower speed and speed and with a low engine speed. with less engine revs for a short time, if necessary. z If unburned fuel enters the catalytic converter, this may result in overheating Catalytic converter, exhaust and irreparable damage to the catalytic emissions converter. Catalytic converter for petrol engines You should therefore avoid frequent cold Leaded fuel will damage the catalytic starts, unnecessarily long use of the converter and parts of the electronic starter when setting off, running the tank system, thereby rendering them dry (an irregular fuel supply leads to inoperative. overheating) and starting the engine by On vehicles with a catalytic converter, the pushing or towing. fuel tank filler neck is of a narrow design so z If the control indicator for exhaust that a dispensing pump for leaded fuel emissions Z flashes, lift your foot off the cannot be inserted. accelerator until the control indicator stops flashing and is steadily lit. Contact a workshop immediately. Control indicator Z for exhaust emissions - see pages 74, 134. 134 Driving and operation
Controlling exhaust emission Control indicator for exhaust emissions Control indicator for engine electronics Through design-related measures, Control indicator Z illuminates for a few Control indicator 3 illuminates for a few primarily in the fuel injection and ignition seconds when the ignition is switched on. seconds when the ignition is switched on. systems (in combination with the catalytic If it illuminates when the engine is running, If it illuminates when the engine is running, converter), the proportion of noxious there is a fault in the emission control there is a fault in the engine electronics. materials in the exhaust, such as carbon system or with the diesel particle filter 3. The electronics switch to the emergency monoxide (CO), hydrocarbons (CH) and The permitted emission values may be running program, fuel consumption may nitrogen oxides (NOx), is reduced to a exceeded. Consult a workshop. increase and the driveability of the vehicle minimum. Flashing with the engine running indicates may be affected. a fault that may damage the catalytic In some cases, the fault can be eliminated converter. The vehicle’s electronic system by switching the engine off and back on will switch to an emergency running again. If the control indicator illuminates program so you may continue to drive again when the engine is running, have the without causing damage, by slowing down cause of the fault eliminated by a until the flashing stops and the control workshop. indicator is steadily lit. Consult a workshop immediately. Driving and operation 135
Exhaust gases Diesel particle filter (DPF) 3 Maintenance The diesel particle filter removes polluting Have all maintenance work carried out at 9 Warning soot particles out of the exhaust. the intervals specified by Opel. We recommend that you entrust this work to Engine exhaust gases contain poisonous The system contains a self-cleaning your Opel Partner, who has proper carbon monoxide, which has no colour or function at certain intervals. The filter is equipment and trained personnel odour and can be lethal if inhaled. cleaned by burning the soot particles at high temperature. This procedure runs available. Electronic testing of systems If exhaust fumes penetrate the vehicle automatically under certain vehicle permits rapid diagnosis and remedy of interior, open the windows and consult a conditions and can take up to 15 minutes, faults. This way, you can be certain that all workshop immediately. during which time fuel consumption may components of the vehicle’s electrical, increase. The smell and the noise that injection and ignition systems operate occur are normal. correctly, that your vehicle has a low level Do not run engine in enclosed spaces, e.g. of pollutant emission and that the catalytic in a garage, or sit in a parked vehicle for an The system cannot automatically clean converter system will have a long service extended period with the engine running. itself under certain vehicle conditions, such life. as driving short distances. Do not drive with tailgate open. If driving You are thereby making an important with the tailgate open is necessary, set fan If control indicator I illuminates, you contribution towards keeping the air clean to highest speed, close windows and should continue driving, and as soon as the and compliance with emissions legislation. ensure air recirculation mode is off, to allow road and traffic situation permits it, entry of outside air. increase speed to more than 50 km/h Checking and adjustment of the fuel- injection and ignition systems is part of the If the underbody or rear of vehicle is (30 mph) and diesel particle filter cleaning will start. scope of a Service. For this reason, you damaged or corroded, you notice a should have all maintenance work carried change in the sound of the exhaust system, Cleaning is quicker at faster speeds and out at the intervals specified in the chapter or whenever you suspect exhaust gases are under load. The engine speed should not "Service, Maintanance" on page 206. penetrating the vehicle interior, consult a drop below 2000 rpm. The control indicator workshop immediately. extinguishes as soon as cleaning is When the vehicle is driven for the first time, complete. wax and oil on the exhaust system may We recommend that you do not turn the evaporate, producing smoke-like emissions ignition off during cleaning. which should not be inhaled. Allow wax and oil to evaporate while the vehicle is in the open air. 136 Driving and operation
Drive control systems When the ESC comes into action, control Electronic Stability Control (ESC) indicator 7 flashes in the instrument panel. The Electronic Stability Control improves Some noise or vibration may be apparent. driving stability when necessary, The vehicle is now in a critical situation; independently of the type of road surface the ESC helps you to keep control of the and the tyre grip. It also prevents the drive vehicle and reminds you to match your wheels from spinning. speed to the road conditions. The system monitors vehicle movements. As soon as the vehicle starts to swerve 9 Warning (understeers/oversteers), engine output is reduced (the sound of the engine changes) Do not let this special safety feature and individual wheels are specifically tempt you into taking risks when driving. braked. This considerably improves the Traffic safety can only be achieved by driving stability of the vehicle on snow and adopting a responsible driving style. ice and on wet or slippery road surfaces. ESC Active & Warning control indicator 7 The control indicator illuminates in yellow ESC is ready for operation after the ignition for approx. 4 seconds when the ignition is is switched on and the ESC control switched on. The system is ready for 7 J indicators , A and illuminate then operation when it extinguishes. extinguish after approx. 4 seconds. Flashing when driving; The system has come into action. The engine output may be reduced (the sound of the engine changes) and the vehicle may be braked automatically to a small degree. Illuminated when driving; Fault in the system. Poor road surface conditions may cause vehicle stability to be impaired. Have the cause of the fault remedied by a workshop. The system’s integrated self- diagnostics allows faults to be quickly remedied. Driving and operation 137
ESC Not Ready control indicator A Switching off Turn off ESC function to allow engine rpm The control indicator illuminates in yellow Control indicator J illuminates in yellow for to increase, by pressing button J. Control for approx. 4 seconds when the ignition is approx. 4 seconds when the ignition is indicator J illuminates in the instrument switched on. switched on. panel. Illuminates to indicate that the system is With ESC active, if wheels are slipping on The ESC function is turned on again by not ready for conditions to operate. wet, snowy or icy roads, engine speed may pressing button J again (control indicator May illuminate in cold conditions. It should not increase when accelerator pedal is extinguishes) or the next time the ignition is extinguish when the vehicle warms up. depressed. The vehicle may not move. switched on. 138 Driving and operation
Hydraulic Brake Assist (HBA) When the ESC function comes into action and recognises any emergency situations requiring hard braking, it automatically delivers increased braking pressure to the wheels. Active Rollover Protection (ARP) If the vehicle moves in an unstable manner, this function helps the vehicle maintain normal stability. Trailer Stability Assist (TSA) 3 TSA monitors vehicle movements when towing a caravan or trailer. If the system detects lurching movements, engine power is reduced and the vehicle/trailer DCS (Descent Control System) To activate combination is selectively braked until the The Descent Control System allows the At speeds below approx. 50 km/h lurching ceases. vehicle to travel at a low speed without (30 mph), press DCS button. The green DCS depressing the foot brake. control indicator 5 will flash in the The vehicle will automatically decelerate to instrument panel, to show DCS is in a low speed and remain at that speed operation. when DCS button 5 is pressed. DCS will not activate at speeds above Use only when descending steep grades 50 km/h (30 mph), even if the button is while driving off-road. Do not use when pressed. driving on normal road surfaces. Unnecessary usage of the DCS function, Some noise or vibration from the brake such as while driving on normal roads, may system may be apparent when DCS is damage the brake system and the ESC active. function. Driving and operation 139
To deactivate Flashing or illumination of the yellow DCS Press DCS button again. The green DCS control indicator 5 reminds the driver that control indicator 5 will extinguish. the friction material needs to cool down: Depressing the foot brake or accelerator drive the vehicle without braking as much will also cause the DCS function to be as possible. deactivated. If the control indicator does not extinguish, have the cause of the fault remedied by a workshop.
Fault The yellow DCS control indicator 5 flashes to indicate that the system is not ready for conditions to operate, due to the high temperature (approx. 350 - 400 °C) of friction material, through severe or repeated braking. It will extinguish when the temperature drops below 350 °C. The yellow DCS control indicator 5 illuminates when there is a malfunction in the system, due to the extremely high temperature (over 400 °C) of friction material, through severe or repeated braking. It will extinguish when the temperature drops below 350 °C. These temperatures may differ according to vehicle conditions or outside conditions. 140 Driving and operation
Cruise control 3 Do not use cruise control if it is not Cruise control can store and maintain advisable to maintain a constant speed speeds over approx. 30 km/h (20 mph). (e.g. in situations presenting a danger to Deviation from the stored speed may occur yourself and other road users, in heavy when driving uphill or downhill. traffic or on winding, slippery or greasy roads). For safety reasons, cruise control cannot be activated until the foot brake has been With automatic transmission, only use depressed once. cruise control while in D. Cruise control is operated with buttons d, When cruise control is active, reaction c and e on the turn signal lever. times may be increased, due to the different position of the feet. 9 Warning
The driver is always responsible for Control indicator for cruise control ensuring that vehicle speed is When driving, control indicator m will appropriate for the speed limit and illuminate when the system is switched on driving conditions - even if cruise control and the desired vehicle speed is stored. is engaged. Illuminated in yellow; Failure to follow the instructions could cruise control is ready for operation by lead to injuries or endanger life. pressing the e button. Illuminated in green; cruise control speed is set by pressing the d button. Driving and operation 141
Increase speed To deactivate With cruise control active, press and hold Switch off cruise control when not needed, the c button and release it when the to avoid accidental activation. desired vehicle speed is reached. Press e button to turn cruise control off. To increase the speed in steps of Control indicator m extinguishes and the c 2 km/h (1.2 mph), tap the button vehicle slowly decelerates. To continue and release it. driving, depress the accelerator pedal in When the c button is released, the the usual manner. current speed is stored and maintained. For safety reasons, cruise control Alternatively, use the accelerator pedal to deactivates under certain driving increase vehicle speed, press the d conditions. button and release it, then release the For example: accelerator pedal. z If the vehicle speed drops below 30 km/h To activate d When the button and the accelerator (20 mph), or Press the e button to turn cruise control pedal are released, the current speed is on. Accelerate to the desired speed, press stored and maintained. z If the brake pedal is depressed, or the d button and release it; the current z If the clutch pedal 3 is depressed, or speed is stored and maintained. The Decrease speed accelerator pedal can be released after With cruise control active, press and hold z If the automatic transmission 3 selector setting cruise control speed. the d button and release it when the lever is in N, or Vehicle speed can be increased desired vehicle speed is reached. z If the traction control aspect of the temporarily for overtaking purposes, To decrease the speed in steps of Electronic Stability Control (ESC) comes by depressing the accelerator pedal. 2 km/h (1.2 mph), tap the d button into action, to limit wheel spin. When the accelerator pedal is released, the and release it. previously stored speed is resumed. Resuming the stored speed When the d button is released, the Press the c button at speeds above current speed is stored and maintained. 30 km/h (20 mph); the speed selected before cruise control was switched off, is resumed. The value of the stored speed is deleted when the ignition is switched off or the e button is pressed. 142 Driving and operation
The acoustic signal may differ depending on the type of object detected. If the vehicle approaches an obstacle when in a forward gear or while reversing, a series of signals can be heard in the vehicle interior. The interval between the signals becomes shorter as the distance is reduced. If the distance is less than 30 cm, the signal will be continuous. 9 Warning
Under certain circumstances, various reflective surfaces on objects or clothing Park pilot 3 as well as external noise sources may To deactivate The park pilot makes parking easier by cause the system to fail to detect The system deactivates automatically measuring the distance between the obstacles. when in neutral (automatic transmission 3 vehicle and any obstacles to the front and The park pilot may not recognise sharp in N or P) with the hand brake applied. rear and giving an acoustic signal in the objects, thick clothes or sponge-like When the vehicle speed is greater than passenger compartment. materials which absorb the frequency. 8 km/h (5 mph), the system also deactivates. The system records the distance using four If the sensors are damaged or covered sensors in both the front and rear bumpers. with snow, dirt or ice, the park pilot may To deactivate the system manually, press To activate not activate. button b on the instrument panel. The park pilot activates automatically The control indicator in the button will For these reasons, care must be taken illuminate. when the ignition is switched on and a when reversing, even if the park pilot is forward gear or reverse gear is engaged operational. This is of particular If the button is pressed again, the control and the hand brake is released. importance when in the vicinity of indicator in the button will extinguish and pedestrians. the system will be reactivated as soon as a forward gear or reverse gear is engaged and the hand brake is released. Driving and operation 143
To ensure the safety of other road users and people in the vicinity and to avoid damage to the vehicle, remember: z The park pilot should only be considered as a supplementary function. Normal precautions should be maintained when reversing. Check the rear view and use the mirrors when reversing. z Do not push, scratch or otherwise damage the sensors. z Do not use high-pressure jet cleaners to clean the sensors. Clean only with a soft sponge and clean water. Control indicator for park pilot Automatic level control 3 Control indicator r illuminates while Automatic level control makes it possible to driving if there is a fault in the system. keep the height of the vehicle constant If the acoustic signal sounds 3 times when subjected to different loads in the continuously when there are no obstacles rear (e.g. when passengers are occupying near the front or rear bumper, there is a the rear seats or when towing a caravan/ fault in the system. trailer). This significantly improves driving conditions. Have the cause of the fault remedied by a workshop. The vehicle is automatically raised at the rear to its previous unloaded level, increasing spring travel and ground clearance. Headlamp range adjustment - see page 97. In the event of malfunctions, do not utilise the vehicle’s full load capacity. Have the cause of the fault remedied by a workshop without delay. 144 Driving and operation
Tyre pressure monitoring system 3 The tyre pressure monitoring system 9 Warning continually checks the pressure of all four wheels while driving. The tyre pressure monitoring system does Ü Board Computer not replace manual checks with a A pressure sensor is integrated in each suitable gauge. BC 1 wheel. Once a minute, the pressure of each BC 2 tyre is sent to a control unit, where it is Check tyre pressures at least every compared. If the system detects one or 14 days and prior to any long journey: Timer more pressure differences, a message the tyres should be checked when cold. Tyres appears on the information display. Don’t forget to check the spare. Current tyre pressures can be shown in the information display. Tyre pressure – see pages 224. For the system to be operational, all wheels must be equipped with pressure sensors Display of current tyre pressure and all tyres must be filled to the Select menu item Tyres from the Board prescribed pressure. The tyre pressure Computer menu. monitoring system automatically detects if the vehicle is being driven with a load of up The current pressure of each tyre is to 3 persons or a full load. displayed. Once the ignition is switched on, the system Warning messages is operational and will continuously A message is given on the information monitor the tyre pressures at speeds of display to warn of inconsistent tyre approx. 40 km/h (25 mph) and above. pressures. In some versions, the message is displayed in abbreviated form. For example, the following messages can be displayed: Driving and operation 145
Brake system The effectiveness of the brakes is an important factor for traffic safety. Ü Board Computer Ü Board Computer In the interest of effectiveness, do not brake unnecessarily hard during the first Tyre pressure Attention! 200 km (125 miles) after new disc brake check rear Front left tyre pads have been fitted. left pressure loss Wear of the brake linings must not exceed (value in bar) (value in bar) a specified limit. Regular maintenance, as detailed on pages 206 to 212, is therefore OK OK of the utmost importance for traffic safety. Have worn brake pads replaced by a workshop. Pads which have been tested A graphic indicating the left rear tyre is A graphic indicating the front left tyre is and passed ensure optimum brake shown together with the current tyre shown together with the current tyre performance. pressure; slight pressure deviation. Reduce pressure; significant pressure deviation or Brake pads worn to their minimum speed. Check pressure at next opportunity direct pressure loss. Steer out of flow of thickness may generate a grinding noise. with appropriate gauge and correct if traffic as quickly as possible without It is possible to continue driving. Have your necessary. endangering other drivers. Stop and check brake pads replaced as soon as possible. On the colour information display 3, the tyres. Seek the assistance of a workshop for this report will appear in yellow. Mount the spare wheel if necessary – replacing the brake pads. see page 177. On the colour information display 3, 9 Warning this report will appear in red. Disregard of these instructions may lead Acknowledgement of warnings – to injuries or endanger life. see page 84. 146 Driving and operation
Foot brake In order to utilise the full pedal travel, The brake system comprises two separate particularly in the event of a brake circuit brake circuits. fault, there must be no mats in the area of If one brake circuit should fail, the vehicle the pedals - see page 128. can still be braked with the second With the engine stopped, the brake servo remaining circuit. assistance is discontinued after the brake If this happens, the brake pedal must be pedal has been depressed once or twice. fully depressed with greater pedal The braking effect is not reduced, but pressure. The distance required for braking increased foot pressure will be necessary. will be greater. Take extra care when the vehicle is being towed. If, at any time during driving, the brake pedal can be depressed further than Check the brake lamps before starting out normal, the vehicle repeatedly pulls to one on a journey. Shortly after the start of each journey, the brake system should be tested Brake assist side under braking or brake noise is heard, consult a workshop. for its effectiveness at low speed and Rapid powerful application of the brake without inconveniencing other road users, pedal automatically applies maximum especially if the brakes are wet, e.g. after brake force amplification to achieve the washing your vehicle. shortest possible braking distance under full braking (brake assist). Excessive braking when going downhill can cause brakes to temporarily overheat. Shift Maintain steady pressure on the brake to a lower gear rather than continuously pedal for as long as full-on braking is to applying brakes. continue. When the brake pedal is released, the maximum brake force The brake fluid level should be checked amplification is taken away. regularly - see page 196. Driving and operation 147
If the control indicator stays lit, the brakes do not operate as normal or leaks are found in the brake system, do not attempt to drive the vehicle. Have the vehicle towed to a workshop for inspection and repair. If the control indicator does not illuminate when the ignition is switched on or when the hand brake is applied (with ignition on), stop and consult a workshop.
Hand brake Control indicator 4 for brake system Always apply hand brake firmly. On slopes, Illuminates when ignition is switched on. apply the hand brake as firmly as possible. Extinguishes after engine is started. The mechanical hand brake acts on the Illuminates if hand brake is applied and/or brakes on the rear wheels. It engages fluid level for brake hydraulics is too low. automatically when applied. Brake fluid level - see page 196. To release the hand brake, press and hold the button, pull the lever up slightly and 9 Warning lower lever while holding the button in. If it illuminates when the hand brake is To reduce the operating forces of the not applied: stop vehicle, interrupt your hand brake, depress the foot brake at the journey immediately. same time. Check brake fluid level and top-up if necessary before consulting a workshop. Have cause of brake fluid loss remedied. 148 Driving and operation
Anti-lock Brake System (ABS) u If control indicator u illuminates during The ABS continually monitors the vehicle's driving along with brake system control brake system and prevents the wheels from indicator 4, there is a serious fault in the locking, irrespective of the road condition brake system. Have the system checked and tyre grip. immediately by a workshop. It starts to regulate the braking pressure as Fault soon as a wheel shows a tendency to lock. The vehicle remains steerable, even in the 9 Warning event of very heavy braking, e.g. on bends or when swerving to avoid an obstacle. If there is a fault in the ABS, the wheels Even in the case of full-on braking, the ABS may tend to lock in the event of unusually makes it possible to drive round an heavy braking. This may cause the obstacle without releasing the brakes. vehicle to swerve. The benefits of the ABS are lost. ABS control is made apparent through a Control indicator u for ABS pulse in the brake pedal and the noise of Illuminates in yellow for approx. 4 seconds the regulation process. when the ignition is switched on. You can continue driving, provided you drive with care and anticipation. 9 Warning At the same time, the system performs a self-check. When the control indicator Have the cause of the fault remedied by a workshop. The system's integrated self- For optimum braking, keep the brake extinguishes, the system is ready for diagnostics allows faults to be quickly pedal fully depressed throughout the operation. remedied. braking process, despite the fact that the If the control indicator does not illuminate pedal is pulsating. Do not reduce the when the ignition is switched on, does not pressure on the pedal. extinguish after approx. 4 seconds, or if it Do not let this special safety feature illuminates during driving, there is a fault in tempt you into taking risks when driving. the ABS. The vehicle's brake system may remain operational without ABS Traffic safety can only be achieved by regulation. adopting a responsible driving style. Driving and operation 149
Wheels, tyres Vehicles with tyre pressure monitoring Some brands of tyres have a beaded edge See page 223 for suitable tyres and system 3 for alloy wheels, to protect against restrictions. When using winter tyres, or when switching damage. If wheel trims are used on steel to different tyre sizes, sensors for the tyre wheels with beaded-edge tyres, the Factory-fitted tyres are matched to the pressure monitoring system can be fitted at following procedure must be followed: chassis and offer optimum driving comfort a later date by a workshop, upon request. and safety. z Wheel trims and tyres that are approved Otherwise, the system would not indicate by Opel for the respective vehicle and tyre pressure deviations. Changing tyre/wheel type comply with all of the relevant wheel and Note the necessary modifications before Tyre pressure monitoring system - tyre combination requirements must be switching to different tyres or wheels. see page 144. used. z If the wheel trims and tyres used are not Fitting new tyres 9 Warning Opel-approved, the tyres must not have New tyres should be fitted in pairs, or, for a beaded edge. Use of unsuitable tyres or wheels may preference, in sets. Make sure that both lead to accidents and render the vehicle tyres on an axle are: 9 Warning unroadworthy. z the same size, z the same design, Use of unsuitable tyres or wheel trims z the same make, could lead to sudden pressure loss and If wheel rims of a different type are to be z and have the same tread pattern. thereby accidents. installed, the wheel nuts may also need to Fit directional tyres such that they roll in the be changed. We recommend you consult direction of travel. The rolling direction is an Opel Partner. indicated by a symbol (e.g. an arrow) on If tyres of a different size to those fitted at the sidewall. the factory are used (this includes winter Tyres fitted opposing the rolling direction tyres), the electronic speedometer may (e.g. when a tyre is changed) should be possibly need to be reprogrammed, to refitted as soon as possible. This is the only ensure that the speed displayed is correct. way to obtain full benefit from the design properties of the tyre. Observe legal requirements when disposing of tyres. 150 Driving and operation
Tyre pressure After having checked the tyre pressures, Tyre condition, wheel condition Check tyre pressures when cold, at least securely tighten the valve caps. Driving over sharp edges can lead to every 14 days and prior to any long Incorrect inflation pressures will impair hidden tyre damage and wheel damage journey. Don't forget to check the spare. safety, vehicle handling, comfort and fuel which is only noticed later on; danger of Use the valve cap key 3 to make economy and will increase tyre wear. tyre blow-out. unscrewing the valve caps easier. The If the pressure is too low, this can result in Drive over edges slowly and at a right valve cap key is located on the inside of the considerable tyre warm-up and internal angle if possible. When parking, ensure tank flap. damage, leading to tread separation and that the tyres are not pressed against the Tyre pressures - see page 224. even to tyre blow-out at high speeds. edge of the kerb. Increased pressure resulting from tyre Hidden tyre damage is not eliminated by Check tyres regularly for damage (foreign warm-up must not be reduced, otherwise subsequently adjusting the inflation bodies, punctures, cuts, cracks, bulges in the pressure may drop below the pressure. sidewalls). Check wheels for damage. In permissible minimum when the tyres cool the event of damage or abnormal wear, down. 9 Warning consult a workshop.
Incorrect tyre pressure could lead to a flat 9 Warning tyre. Damage may lead to tyre blowout. Driving and operation 151
General information Note that the danger of aquaplaning is greater if the tyres are worn and if the tyre pressures are not correct. Tyres age, even if they are used only very little or not at all. A spare wheel which has not been used for six years should be used only in emergencies: drive slowly when using such tyres. Never fit used tyres the previous history and use of which you do not know.
Tread depth For safety reasons, tyres should be Check tread depth regularly. Should the replaced when their tread depth has worn front tyres show greater wear than the rear down to 2 to 3 mm. The legal permissible tyres, have both front wheels exchanged minimum tread depth (1.6 mm) has been with the rear wheels so that the tyres with reached when the tread has worn down as deeper tread are on the front axle. far as one of the wear indicators. For information on how to change a wheel A number of wear indicators are spaced at - see page 178. equal intervals around the tyre, within the Check the tyre pressures - see page 224. tread. Their position is indicated by markings on the tyre sidewall. 152 Driving and operation
Tyre designations Winter tyres 3 Meanings: See page 223 for restrictions. e.g. 235/60 R 17 102 H Winter tyres improve safety at extremely 235 =Tyre width inmm low outside temperatures and should therefore be fitted on all wheels. 60 =Aspect ratio (tyre height to tyre width in %) The design of summer tyres means they R =Belt type: Radial have limited qualities for winter driving. 17 = Rim diameter in inches If the maximum permissible speed for the 102 =Load index winter tyres is less than that of the vehicle, e.g.: 91 represents 618 kg a notice indicating the maximum H = Speed code permissible speed for the tyres must be affixed within the driver's field of vision 3 1). Speed code letters: If you use the spare wheel when it is fitted Q Up to 160 km/h (100 mph) with a summer tyre; the vehicle's Tyre chains 3 S Up to 180 km/h (112 mph) driveability may be affected, especially on See page 223 for restrictions. T Up to 190 km/h (118 mph) slippery road surfaces. Obtain a Tyre chains must not be used on the H Up to 210 km/h (130 mph) replacement for the faulty tyre as soon as temporary spare wheel. If you need to use possible, and have the wheel balanced V Up to 240 km/h (150 mph) tyre chains after suffering a flat front tyre, and fitted to the vehicle. W Up to 270 km/h (168 mph) fit the temporary spare wheel on the rear Ensure that winter tyres are inflated to the axle and transfer one of the rear wheels to correct pressure specified by the tyre the front axle. manufacturer. If winter tyres are installed that have not been approved for your vehicle, ESC performance may be affected. Consult a workshop regarding availability of approved winter tyres. Wheel trims 3 If the wheel trims and tyres used are not Opel-approved, make sure the tyres do not have a beaded edge - see page 149.
1) Varies from country to country on account of national regulations. Driving and operation 153
Always use fine-linked chains that add no Temporary spare wheel Roof racks 3 more than 15 mm to the tyre tread and the The temporary spare wheel is designed for inboard sides (including chain lock). use on your vehicle only. 9 Warning Tyre chains may only be used at speeds of Do not attempt to use the spare tyre on a Disregard of the instructions may lead to up to 50 km/h (30 mph)1) or up to the tyre different wheel, or use a different tyre on injuries or endanger life. Vehicle chain manufacturer’s recommended the spare wheel, as they will not fit. passengers must be informed maximum speed, whichever is lower. For notes on the temporary spare wheel - accordingly. When travelling on roads that are free of see page 178. snow, they may only be used for brief Ensure the temporary spare wheel is For reasons of safety and to avoid periods since they are subject to rapid wear inflated to the correct tyre pressure - on a hard road and may snap. damaging the roof, we recommend that see page 224. you use the Opel roof rack system Avoid sharp turns, bumps and holes and Wheel changing - see page 178. approved for your vehicle. do not lock the wheels when braking, to avoid damaging the tyre chains. Fasten the roof rack to the roof rails following the instructions that accompany Retighten the chains after driving for the system, ensuring that the roof load is approx. 1 km (0.6 miles). If, at any time, evenly distributed over the side or cross you hear or suspect that the chains are rails. Loads must not be placed on the roof contacting the vehicle, stop and retighten surface. the chains. To prevent damage or loss, check Always read the instructions supplied with frequently that roof loads are securely the tyre chains. fastened. Driving with a roof load affects the vehicle’s centre of gravity; drive carefully in crosswinds and do not drive at high speeds. Driving hints - see page 127.
1) Varies from country to country on account of national regulations. 154 Driving and operation
Flex-Fix system 3 Extend Flex-Fix system Completely pull out the Flex-Fix system The Flex-Fix system allows up to two Open tailgate - see page 26. until you hear it engage. bicycles to be attached to a pull-out carrier Ensure that it is not possible to push in the integrated beneath the vehicle floor. 9 Warning Flex-Fix system without pulling the release lever again. The maximum load is 40 kg. No persons may remain in the extension If not in use, the Flex-Fix system has to be zone of the Flex-Fix system while collapsed back beneath the vehicle floor. opening; risk of injury. There must not be any objects on the bicycles that could become loose during Raise the release lever. The system transportation. disengages and travels quickly out from A multifunction box 3 is offered as an the bumper. accessory for the carrier system. The transportation of other objects is not permitted. Driving and operation 155
Pull up license plate holder and fully insert Install the tail lamps Open out the lamp support on the back of the holder supports into the retainers. Remove the left tail lamp (1), then the right the tail lamp all the way. tail lamp (2) from the storage bay. 156 Driving and operation
Push the clamping lever and insert the Check the cable and lamp position to make Lock the Flex-Fix system lamp support into the retainer until it hits sure these are correctly installed and are Swivel the left clamping lever (1) outwards the stop. securely located. first, followed by the right clamping lever Perform this procedure for both tail lamps. (2) until they stop. Both clamping levers must point backwards, otherwise safe functionality is not guaranteed. 9 Warning
It is only permissible to fit objects to the Flex-Fix system if the system has been correctly engaged. If the Flex-Fix system will not engage correctly, do not fit objects to the system and slide the system back. Contact a workshop for assistance.
Close the tailgate. Driving and operation 157
Unfold pedal crank recesses Remove the pedal crank mounts from the Adapting the Flex-Fix system to a bicycle Fold one or both pedal crank recesses pedal crank recesses. With the rotary lever on the pedal crank upwards until the diagonal support recess, roughly adapt the adjustable pedal engages. crank unit to the protrusion of the pedal crank. If the bicycle has straight pedal cranks, unscrew the pedal crank unit all the way (position 5), see illustration. 158 Driving and operation
If the bicycle has curved pedal cranks, Press the release lever and withdraw the Push the release lever on the strap retainer screw in the pedal crank unit all the way wheel recesses. and remove the strap retainer. (position 1), see illustration. Driving and operation 159
Prepare the bicycle for attachment Attaching a bicycle to the Flex-Fix system Insert pedal crank mount into outer rail of Rotate the left pedal (opposite the chain Put on the bicycle. The pedal crank here each pedal crank recess from above and cog) vertically downwards. The pedal on must be placed in the pedal crank recess slide downwards as far as it will go, the left pedal crank must be horizontal. opening as shown in the illustration. see Fig. 18454 S on page 160. The front bicycle must have its front wheel facing left. The rear bicycle must have its front wheel facing right. 160 Driving and operation
Attach the pedal crank by rotating the Place the wheel recesses such that the Align the bicycle in the longitudinal attachment screw on the pedal crank bicycle is more or less horizontal. Here, the direction of the vehicle: mount. distance between the pedals and the Slightly loosen the pedal bearing mount - tailgate should be at least 5 cm. Setting the see page 157, Fig. 14629 S. wheel recesses - see page 158. Place the bicycle upright using the rotary Both bicycle tyres must be in the wheel lever on the pedal crank recess - recesses. In order to prevent damage, see page 157, Fig. 14629 S or page 158, neither the pedal bearing housing on the Fig. 14630 S. bicycle nor the pedal crank should be touching the pedal crank recess. If the two bicycles obstruct one another, the relative positions of the bicycles can be adapted by adjusting the wheel recesses and the rotary lever on the pedal crank recess until the bicycles no longer touch one another. Make sure there is sufficient clearance from the vehicle. Driving and operation 161
Tighten the attachment screw for the pedal Removing a bicycle from the Flex-Fix Retracting the Flex-Fix system bearing mount to its maximum point. system Push the pedal crank mounts into the Secure both bicycle wheels to wheel Undo strap retainers on both bicycle tyres. pedal crank recesses. recesses using strap retainers. Hold on to the bicycle, loosen the Check the bicycle to make sure it is secure. attachment screw for the pedal bearing mount, then lift the pedal bearing mount to The settings for the wheel recesses and the remove it. rotary lever on the pedal crank recess should be noted and saved for each Remove bicycle from the Flex-Fix system. bicycle. Correct presetting will facilitate refitting of the bicycle. 162 Driving and operation
Secure the strap retainer and pull tightly Press release lever and slide in wheel Disengage the locking lever on the downwards as far as possible. recesses all the way as far as they will go. diagonal support and fold both pedal crank recesses down. 9 Warning
Caution; risk of trapping fingers. Driving and operation 163
Swivel first the right clamping lever (1), Push the clamping lever and pull both lamp Fold in the lamp supports on the backs of inwards, followed by the left clamping lever supports out of the recesses. the tail lamps. (2), until they can be engaged in their First place the right tail lamp (1), then the respective recesses. left tail lamp (2) in their respective recesses and push down as far as possible. Push cables all the way into all guides in order to prevent damage. 164 Driving and operation
Towing equipment 3 If the vehicle is not equipped with a trailer hitch, we recommend having this retrofitted by a workshop, who will advise you on any possible towed load increases. The workshop has instructions on how to install the trailer hitch and making any changes to the vehicle that are needed that affect the cooling system, heat shields or other equipment. 9 Warning
The coupling ball bar is to be removed Pull up license plate holder and fold down Open the tailgate. when not towing. into horizontal position. Raise the release lever and push the system into the bumper until it engages. Mounting dimensions of towing equipment Ensure release lever returns to original - see page 227. position. 9 Warning
If the system cannot be correctly engaged, please contact a workshop for assistance. Driving and operation 165
Towing equipment with detachable coupling ball bar 3 Stowage of coupling ball bar The coupling ball bar is kept in a bag, fastened with a strap and is stowed below the floor cover in the luggage compartment.
Fitting the coupling ball bar Confirm that the colour marking on the Remove sealing plug from the hole for the lever is red. coupling ball bar and stow it in the luggage compartment. 166 Driving and operation
Important Check that the coupling ball bar is correctly attached: z Green marking must be visible on lever. z Coupling ball bar must be seated firmly in coupling housing. Coupling ball bar must be locked and key must be removed. 9 Warning
Towing a caravan/trailer is only permitted with a properly attached Inserting the coupling ball bar Lock coupling ball bar by turning the coupling ball bar. If the coupling ball bar Insert the coupling ball bar into the supplied key in the lock cylinder of the cannot be properly attached, consult a coupling housing and push firmly coupling ball bar. workshop. downwards until the coupling ball bar Remove key. audibly engages. Eye for breakaway stopping cable 3 If it does not engage, repeat fitting In the case of caravans/trailers with procedure. brakes 3, attach the breakaway stopping cable to the eye - not the coupling ball bar. Do not swing the coupling ball bar to the left or right, or upwards and downwards, to avoid disrupting correct fitting. Driving and operation 167
Towing Since engine power decreases as altitude Caravan/trailer loads1) increases because of the air becoming The permissible caravan/trailer loads are thinner, therefore reducing climbing ability, vehicle-dependent and engine-dependent it may not be possible for permissible trailer maximum values which must not be loads to be fully utilized in mountainous exceeded. territory. The actual caravan/trailer load is the The permitted towing weight decreases by difference between the actual gross weight 10% for every 1000 metres of additional of the caravan/trailer and the actual altitude. coupling socket load with the caravan/ The towing weight does not have to be trailer coupled. reduced when driving on roads with slight When the caravan/trailer load is being inclines (less than 8%, e.g. on motorways). checked, therefore, only the caravan/trailer The actual caravan/trailer load plus the Dismounting the coupling ball bar wheels - and not the jockey wheel - must be actual Gross Vehicle Weight must not Unlock coupling ball bar and remove key. standing on the weighing apparatus. exceed the maximum permitted towing weight. For example, if the permitted Gross Push lever to the left, towards the coupling The permissible caravan/trailer loads for your vehicle are given in the vehicle papers. Vehicle Weight is utilised, the caravan/ ball bar and turn it downwards. Pull trailer load must only be used until the coupling ball bar out of coupling housing. Unless otherwise stated, they are valid for gradients up to max. 12%. maximum permitted towing weight is Remove any rust or dirt from area around reached. the coupling housing and coupling ball bar The permissible caravan/trailer load should be fully utilized only by drivers who are The maximum permitted towing weight is connection before inserting sealing plug in shown on the vehicle identification plate - the hole. adequately experienced in towing large caravans/trailers. see page 215. Place the coupling ball bar in the bag supplied, fasten it with the strap and stow The permitted caravan/trailer load applies it below the floor cover in the luggage up to the specified incline and up to an compartment. altitude of 1000 metres above sea level. Do not use steam-jet cleaners or other high-pressure cleaners to clean the coupling ball bar.
1) Observe national regulations. 168 Driving and operation
Coupling socket load Rear axle load during towing The coupling socket load is the load When the caravan/trailer is coupled and exerted by the caravan/trailer on the the towing vehicle fully loaded (including coupling ball. It can be varied by changing all occupants), the permissible rear axle the weight distribution when loading the load must not be exceeded. caravan/trailer. National regulations regarding maximum The maximum permissible coupling socket speeds for vehicles towing a caravan/ load for the towing vehicle (80 kg) is stated trailer must be observed. on the towing equipment identification plate and should always be aimed for, particularly in the case of heavy caravans/ trailers. The coupling socket load should never be below 25 kg. When measuring the coupling socket load, make sure that the drawbar of the loaded Tyre pressure caravan/trailer is at the same height as it Increase the tyre pressure on the towing will be when the caravan/trailer is coupled vehicle to the value specified for full load with the towing vehicle loaded. This is (see page 224). Also check the pressure of particularly important for caravans/trailers the caravan/trailer tyres. with tandem axle. Driving and operation 169
Driving characteristics, towing tips In the case of caravans/trailers with low When coupled to a caravan/trailer, the In the case of caravans/trailers with directional stability, it is advisable to use a vehicle requires more braking effort when brakes 3, attach the breakaway stopping friction-type stabilizer to damp rolling driving down long gradients, so select the cable to the eye 3 or loop around coupling motions. same gear as you would when driving ball bar if no eye is available. Do not drive faster than 80 km/h (50 mph), uphill and drive at roughly the same speed. Ensure cable is crossed under the coupling even in countries where higher speeds are Automatic transmission in automatic mode socket to ensure the caravan/trailer nose permitted. will select the driving program with the cannot drop to the ground if it becomes When driving uphill, do not drive faster optimum engine braking effect. separated from the trailer hitch. than 30 km/h (20 mph) in 1st gear, or Remember that braking distances for Do not allow the cable to drag along the 50 km/h (30 mph) in 2nd gear. vehicles towing caravans/trailers with and ground and always allow enough slack to Make sure that you have enough room without brakes is always greater than for permit full turning. Follow the instructions when cornering and avoid sudden vehicles not towing a caravan/trailer. For supplied with the towing equipment. manoeuvres. caravans/trailers with brakes, follow the Before coupling the caravan/trailer, instructions carefully. Do not make any If the caravan/trailer starts to sway, drive modifications to the brake system. lubricate the ball of the caravan/trailer more slowly, do not attempt to correct the towing device. However, do not do so if a steering and brake sharply if necessary. Always check lamps on caravans/trailers stabilizer which acts on the coupling ball is before towing. Ensure national regulations being used to damp rolling motions. If it is necessary to apply the brakes fully, are observed. depress the brake pedal as hard as Handling is greatly influenced by the possible. The fog tail lamp on the vehicle is loading of the caravan/trailer. Loads deactivated when towing a caravan/ should therefore be secured so that they The cooling fan is electrically operated. trailer. cannot slip and should be placed in the The fan cooling capacity is not, therefore, dependent on engine speed. It is not When reversing, if possible, have someone centre of the caravan/trailer if possible, provide assistance. i.e. above the axle. necessary, when driving uphill, to shift down into a lower gear if the vehicle can Drive slowly and shift down into a lower Opel genuine parts and accessories which climb in a higher gear. gear when descending steep gradients can be subsequently fitted aid trailer rather than holding the foot brake operation, e.g. large mirrors for wide depressed, to avoid overheating and caravans/trailers. reduced brake efficiency. 170 Driving and operation
Block the wheels of both the caravan/trailer and the vehicle when parking and always apply the hand brake firmly. If possible, do not park on slopes. 9 Warning
Have someone provide assistance when removing blocks. Always remove blocks from wheels while standing to one side. Do not remove blocks while standing behind the caravan/trailer; risk of injury and damage to both the vehicle and caravan/trailer. Parking on inclines Starting on inclines If parking on an incline is unavoidable, Depress the foot brake and hold it down, depress the foot brake, have someone start the engine, shift into gear and release place wheel blocks under the caravan/ the hand brake. trailer wheels and release the foot brake Release foot brake and drive slowly until until the blocks have absorbed the load. the caravan/trailer is clear of the wheel Depress foot brake again, apply blocks. Stop the vehicle and have someone hand brake, engage first gear on uphill pick up the blocks. If possible, the engine gradients or reverse gear on downhill speed should not drop during this gradients (automatic transmission 3 in P) procedure. and finally, release foot brake. For vehicles with automatic transmission 3 in automatic mode, apply sufficient throttle. Before starting-off under extreme conditions (e.g. high combination weight, mountainous terrain with steep inclines), switch off all unnecessary electrical loads (e.g. heated rear window, air conditioning system, heated front seats 3). Self-help, vehicle care 171
Self-help, vehicle care 9 Warning
Disregard of the instructions may lead to injuries or endanger life. Vehicle passengers must be informed accordingly. Diesel fuel system, bleeding ...... 171 Bonnet ...... 171 Starting...... 172 Diesel fuel system, bleeding Starting the engine with jump leads 3 172 Never let the fuel tank run dry. If control indicator Y illuminates, refuel as soon as Towing...... 174 possible. Jack and vehicle tools ...... 176 It is possible to restart the engine if the tank Warning triangle ¨ 3, 177 has been run dry. A delayed start can be First aid kit +3...... expected. Switch on the ignition three times Bonnet Temporary spare wheel ...... 177 for approx. 15 seconds. Then try to start To open the bonnet, pull release lever / Wheel changing...... 178 the engine for no more than 40 seconds. If located on the left-hand side below the Electrical system ...... 181 the engine will not start, wait at least instrument panel. Fuses and the most important circuits 10 seconds before trying again. If the The bonnet will then be unlocked and will they protect ...... 182 engine will still not start, consult a partially open. Return release lever to its workshop. Bulb replacement ...... 185 original position. Opel genuine parts and accessories. 191 Do not pull release lever while the vehicle is A note on safety ...... 191 moving. Checking and topping up fluids...... 191 Windscreen wipers...... 198 Windscreen washer system...... 199 Battery...... 200 Protection of electronic components 201 Vehicle storage ...... 201 Vehicle care...... 201 172 Self-help, vehicle care
Starting Starting the engine with jump Do not start with quick charger leads 3 This prevents damage to electronic A vehicle with a discharged battery can be components. started using jump leads and the battery of another vehicle. 9 Warning Start attempts should be made at intervals If the vehicle battery requires charging of 1 minute and should not last longer than whilst still in the vehicle, ensure there is 15 seconds. adequate ventilation in and around the battery compartment, to prevent risk of 9 Warning explosion. This must be done with extreme care. Any deviation from the following instructions Do not start by pushing or towing could lead to personal injury or damage To open completely, locate the safety Because your vehicle is fitted with a resulting from battery explosion, as well catch, found slightly left of centre on the catalytic converter, it must not be started as to damage to the electrical systems in underside of the bonnet, push the catch by pushing or towing - see page 133. both vehicles. upwards and lift the bonnet gently. The bonnet is held open automatically. The vehicle can only be started using jump leads - see following pages. When the bonnet is opened, leaves, dirt or snow on the bonnet can slide down and obstruct the air intake. Remove any leaves, dirt or snow. Air intake - see page 114. Never drive with bonnet open. To close bonnet, lower it gradually, allowing it to drop from a height of approx. 30 cm. Check that the bonnet is locked in position before driving, by pulling at its front edge. If it is not engaged, repeat closing procedure. Self-help, vehicle care 173
z Use auxiliary battery with same voltage (12 volts). Its capacity (Ah) must not be considerably less than that of the discharged battery. Voltage and capacity information can be found on the batteries. z Use jump leads with insulated terminals and a width of at least 16 mm2 (25 mm2 for diesel engines). z Do not disconnect the discharged battery from the vehicle. z Switch off all unnecessary electrical consumers. Infotainment system may be z Never expose the battery to naked damaged if switched on while jump Connect the leads in the order shown in the flames or sparks. starting. illustration: z A discharged battery can freeze at z Do not lean over the battery during jump 1. Connect one end of the first jump lead to temperatures of 0 °C. Defrost the battery starting procedure. the positive terminal 1 of the battery in a warm room before connecting the z Do not allow the terminals of one lead to providing the jump start (identified by jump leads. touch those of the other lead. “+” sign on battery case or terminal). z Do not allow battery fluid to contact z The vehicles should not touch while jump 2. Connect the other end of the first jump eyes, skin, fabrics or painted surfaces. starting. lead to the positive terminal 2 of the The fluid contains sulphuric acid which discharged battery (“+” sign). z Apply hand brake. can cause injuries and damage in the 3. Connect one end of the second jump z Manual transmission in neutral, event of direct contact. lead to the negative terminal 3 of the automatic transmission 3 in P. z Wear eye protection and protective battery providing the jump start clothing when handling a battery. (identified by "-" sign on battery case or terminal). 4. Connect the other end of the second jump lead 4 to ground on the vehicle with the discharged battery, e.g. on the engine block. 174 Self-help, vehicle care
Place gearshift lever in neutral. Switch on 9 Warning the ignition to release the steering column lock and to permit operation of the brake Care must be taken to ensure that the lamps and windscreen wipers. leads do not inadvertently contact metal surfaces within the compartment area. Drive off slowly and avoid jerky movements. Impermissible tractive forces could damage the vehicles. z Do not connect leads to negative terminal of discharged battery. 9 Warning z The last connection point should be as far away from the discharged battery as More brake pedal pressure is necessary possible. when braking since the brake servo unit is operative only when engine is running. z Route leads so they cannot catch on rotating parts in engine compartment. Considerably greater steering force is Towing necessary since this unit is operative only z Start the engine of the vehicle providing Towing the vehicle when the engine is running. the jump start. Attach a tow rope 3 - or better still a tow z After 5 minutes, start the other engine. rod 3 - to the front towing eye (located Start attempts should be made at under the front bumper). Do not tow the intervals of 1 minute and should not last vehicle from the rear. longer than 15 seconds. The front towing eye must only be used for z After starting, allow both engines to idle towing and not recovering the vehicle. for approx. 3 minutes with leads connected. 9 Warning z In order to avoid excess voltage in the Never lift vehicle using the towing eye. electrical system, before removing a lead, switch on an electrical consumer (e.g. lamps, heated rear window) in the vehicle receiving the jump start. z Operate discharged vehicle for approx. 20 minutes to allow for recharging. z Reverse above sequence exactly when removing leads. Self-help, vehicle care 175
Keep tow rope 3 clear of front bumper, Towing service and ensure it is securely fixed to the towing Entrust your vehicle only to the towing eye at both ends. Pull on the tow rope 3 to service of your choice and obtain an check. estimate on towing costs before employing To prevent entry of exhaust fumes from any towing service. This will prevent towing vehicle, switch on air recirculation unnecessary expense and possible mode (see page 109) and close the insurance problems during claim windows. processing. Never let passengers ride in a vehicle that Use flatbed equipment whenever possible. is being towed. If vehicle is to be towed using a wheel lift, tow with all wheels off the road, using a Never tow a vehicle with damaged parts towing dolly. that are not secured to the vehicle or if wheels, brakes or steering are damaged. Never use sling-type equipment to tow the vehicle or tow the vehicle with the front or Do not tow the vehicle with a tow rope 3 or rear wheels on the road, to avoid causing Towing another vehicle tow rod 3 for extended periods, to avoid serious damage to the vehicle. In emergency situations only, attach a tow damage to the vehicle. Only tow in this rope 3 - or better still a tow rod 3 - to the manner on hard-surfaced roads. Place the gearshift lever in neutral rear towing eye. (automatic transmission 3 in N), switch on For vehicles with automatic transmission 3: hazard warning lamps, turn key to ignition The rear towing eye attachment 3 is stored use flatbed or wheel lift equipment only. switch position ACC and release the below the floor cover in the luggage Towing can cause severe damage to the hand brake before towing the vehicle. compartment. transmission. Remove the cover located on the rear Seek the assistance of a workshop. bumper by pressing the lower part of the cover. 176 Self-help, vehicle care
Screw the rear towing eye attachment anti- clockwise until it is firmly in place. 9 Warning
Never lift vehicle using the towing eye.
Drive off slowly and avoid jerky movements. Impermissible tractive forces could damage the vehicles. To prevent damage, do not take up slack in the tow rope too quickly. After towing, unscrew the rear towing eye attachment clockwise to remove, and Jack and vehicle tools To remove the jack and vehicle tools, open reinstall the cover. The jack and vehicle tools have been the tailgate. Push both levers on the floor specially developed for your vehicle and cover towards the handle and pull up the must only be used on that vehicle. Only use floor cover by the handle. jack for changing wheels. Hang the hook to the upper part of the The jack and vehicle tools are located in tailgate opening (see page 63, Fig. the luggage compartment below the floor S 13419). cover. Remove wing bolt from the jack by rotating it anti-clockwise and remove the jack and 9 Warning wheel wrench bag.
In a sudden stop or a collision, loose items Remove straps holding the bag containing can be thrown around inside the vehicle, the wheel wrench. Remove wheel wrench causing personal injury and damage to from the bag. the interior. Secure the jack and vehicle tools away properly under the floor cover in the luggage compartment. Self-help, vehicle care 177
Warning triangle ¨ 3, General information First aid kit + 3 If you use winter tyres 3, the spare wheel Your first aid kit and warning triangle can may still be fitted with a summer tyre. be accommodated below the floor cover in If you use the spare wheel when it is fitted the luggage compartment. with a summer tyre, the vehicle's driveability may be affected, especially on slippery road surfaces. Obtain a replacement for the faulty tyre as soon as possible, and have the wheel balanced and fitted to the vehicle.
Temporary spare wheel The temporary spare wheel is located in the luggage compartment below the floor cover and is secured with a screw-in retainer. Push both levers on the floor cover towards the handle and pull up floor cover by the handle (see page 176, Fig. S 13700). Hang the hook to the upper part of the tailgate opening (see page 63, Fig. S 13419). Remove the retainer by rotating it anti- clockwise, and remove spare wheel from the spare wheel well. 178 Self-help, vehicle care
Notes on temporary spare wheel Notes on directional tyres 3 Wheel changing z Using a temporary spare wheel may Tyres with a prescribed rotating direction In order to reduce the chance of possible change the driving behaviour of the can only achieve their maximum injuries, make the following preparations vehicle, particularly if using winter performance if they are fitted in the and note the procedure: tyres 3. Replace defective tyre as quickly prescribed rotating direction. as possible, balance wheel and fit to z Park on a level, firm and non-slippery If a tyre or spare wheel is fitted that is surface. vehicle. rotating in the wrong direction due to a z Fit only one temporary spare wheel. puncture, the following must be noted: z Switch on hazard warning lamps and apply hand brake. Engage 1st gear or z Do not drive faster than 80 km/h z The handling of the vehicle may be reverse (automatic transmission 3 in P). (50 mph). different. Replace defective tyres as soon z Correctly set up warning triangle 3. z Take curves slowly. as possible, have wheel balanced and fitted to the vehicle. z Ensure all vehicle passengers are out of z Do not use the temporary spare wheel z the vehicle and clear of the vehicle and for a lengthy period. Do not drive faster than 80 km/h (50 mph). other traffic. z Replace temporary spare wheel with full z z Take the spare wheel from under the specification wheel without delay. Drive particularly carefully on wet and snow-covered road surfaces. luggage compartment floor cover - z When temporary spare wheel is fitted, do see page 177. z not take the vehicle through an For more information on tyres with a prescribed rotating direction - z Before raising the vehicle, turn front automatic car wash with guide rails. The wheels to straight-ahead position. temporary spare wheel may get caught see page 149. on the rails, causing damage to the tyre, wheel and other vehicle parts. z Tyre chains are not permitted on the temporary spare wheel. If tyre chains are necessary after a front wheel puncture, fit the temporary spare wheel to the rear and a rear wheel to the front. Check tyre pressure and adjust if necessary - see page 224. z Follow the temporary spare wheel instructions on pages 153, 181, 223. Self-help, vehicle care 179 z Remove wheel trim 3. z Do not raise the vehicle more than is z Slacken wheel nuts one turn only before necessary to change a wheel. raising the vehicle, but do not totally z No people or animals may be in the unscrew or remove the nuts until the vehicle when it is jacked-up. wheel is off the ground. z Never start or run the engine or crawl z Never change more than one wheel at a under a jacked-up vehicle. time. z Before screwing on the wheel nuts when z Block wheel diagonally opposite the changing a wheel, apply a light coating wheel to be changed, by placing wedge of grease to the cone of each wheel nut. blocks or equivalent in front and behind z Fully tighten the wheel nuts after the wheel. lowering the vehicle all the way, ensuring z Do not jack-up the vehicle when traffic is nuts have been tightened to the correct too close. torque (see page 223). 3 z Use jack only when changing wheels. z If conditions are not satisfactory to 1. Prise off the wheel trim . 2. Slacken the wheel nuts by one turn z Never exceed jack maximum working change a wheel safely, consult a workshop. each using the wrench, putting the load (900 kg). wrench on as far as possible. z If the ground on which the vehicle is standing is soft, a solid board (max. 1 cm thick) should be placed under the jack. Using a thicker board could lead to damage of the jack and the vehicle. 180 Self-help, vehicle care
3. The location of front and rear jacking 4. Before positioning the jack, set it to the 5. Attach wrench to eye of threaded rod points is indicated by notches on the necessary height by rotating the eye by and turn crank to raise vehicle. bottom edge of the vehicle, under the hand. If this is not the case, carefully lower the doors. Position jack at the front or rear jacking vehicle immediately and reposition the point located nearest to the wheel jack. concerned so that the jack claw spans Raise the vehicle until the wheel is just the vertical base. Make sure it is properly clear of the ground. positioned. The jack base must be on the ground 6. Unscrew wheel nuts completely by directly below the jacking point in a turning anti-clockwise and wipe clean manner that prevents it from slipping. with a cloth. Then apply a light coating of grease to the cone of each wheel nut. Do not grease the threads. Put wheel nuts somewhere where the threads will not be soiled. Self-help, vehicle care 181
11. Stow replaced wheel in luggage Electrical system compartment. 9 Warning 12. Stow the jacking equipment and warning triangle 3 - see pages 176, Electronic ignition systems generate very 177. high voltages. Do not touch the ignition system; high voltage can be fatal. 13. Check the tyre pressure of the newly fitted wheel - see page 224. Adjust as necessary. Fuses There are two fuse boxes in the vehicle: 14. Have the new wheel balanced on the the instrument panel fuse box is located on vehicle and have the tightening torque the left-hand side of the front passenger’s of the wheel nuts checked as soon as footwell, the engine compartment fuse box possible, and if necessary, corrected. is located next to the coolant reservoir. 7. Change the wheel. Tightening torque - see page 223. It is advisable to carry a full set of fuses. Notes on spare wheel - see page 178. 15. Replace defective tyre on the wheel Spare fuses are kept in the engine 8. Screw on wheel nuts and tighten that was removed. compartment fuse box. slightly by hand until wheel is held against the hub. 16. Replace temporary spare wheel with a full specification wheel without delay. 9. Rotate wrench anti-clockwise and lower vehicle to the ground.
10. Tighten wheel nuts in a cross wise sequence, putting the wrench on as far as possible. 182 Self-help, vehicle care
Only install fuses of the specified rating. Each fuse has its rating written on it, in addition the fuses are colour coded. Fuses, Fuses, Colour Rating1) Grey 2 A Light brown 5 A Dark brown 7.5 A Red 10 A Light blue 15 A Yellow 20 A White 25 A When replacing a fuse, turn off the Light green 30 A Fuses and the most important respective switch and the ignition. Orange 40 A circuits they protect A defective fuse can be recognized by its Dark blue 60 A Instrument panel fuse box melted wire. A new fuse should only be Located in the left-hand side of the front 1) installed after the cause of the trouble has Rating in Amperes. passenger’s footwell. Release latch to open been eliminated. cover. There is a fuse extractor in the engine To help in replacing fuses, a fuse extractor compartment fuse box. Do not use tools is located in the engine compartment fuse that conduct electricity when changing box. fuses. Self-help, vehicle care 183
No. Circuit Rating 27 -- 28 Windscreen washer 10 A 29 Exterior mirror heating 15 A 30 Instrument cluster 10 A 31 Ignition 10 A 32 Airbag 10 A 33 Steering wheel remote 2 A 34 Folding mirrors 10 A 35 -- 36 Cigarette lighter 20 A Some circuits may be protected by several 37 Passenger’s electric 20 A fuses. No. Circuit Rating window 13 Stop 15 A No. Circuit Rating 38 Driver’s electric window 20 A 14 Headlamp washer 15 A 1 Accessory socket 20 A 39 Automatic transmission 10 A 2 Seat heating 20 A 15 Rear cluster 10 A 3 Audio 15 A 16 Air conditioning 15 A 4 Trailer 10 A 17 Body Control Module 20 A 5 Parking lamp (right side) 10 A 18 Body Control Module 15 A 6 Air conditioning 10 A 19 Ignition switch 2 A 7 Power steering 10 A 20 Fog tail lamp 10 A 8 Body Control Module 10 A 21 Airbag 10 A 9 Anti-theft alarm 10 A 22 Front door lock 15 A 10 Central door locking 20 A 23 Accessory socket 20 A 11 Turn signal (right side) 15 A 24 Transmission Control 15 A Module 12 Turn signal (left side) 15 A 25 Engine 15 A 26 Body Control Module 10 A 184 Self-help, vehicle care
Engine compartment fuse box Some circuits may be protected by several The fuse box is located next to the coolant fuses. No. Circuit Rating reservoir in the engine compartment. No. Circuit Rating 11 Cooling fan auxiliary 30 A 12 Stop 15 A 9 Warning 1 Engine 1 15 A 2 Engine 2 15 A 13 Seat heating 20 A Switch off engine before opening the 3 Engine Control Module 20 A 14 ABS module 20 A engine compartment fuse box; risk of 4 15 ABS module 40 A injury. Engine 3 15 A 5 Air conditioning 10 A 16 Horn 15 A 6 Main 10 A 17 Wipers 25 A To open, disengage cover and tilt upwards. 7 Starter 20 A 18 Run 40 A To help in replacing fuses, a fuse extractor 19 Accessory/Ignition 40 A is located in the engine compartment fuse 8 Cooling fan 30 A box. 9 Fuel pump 15 A 20 Sun roof 20 A 10 All Wheel Drive (AWD) 15 A 21 Anti-theft system 15 A Self-help, vehicle care 185
No. Circuit Rating Bulb replacement 22 Electric seat 30 A Before replacing a bulb, switch off ignition and relevant switch. 23 Battery 60 A Only hold new bulbs at base! Do not touch 24 Defogger 30 A the bulb glass with bare hands, otherwise 25 Dipped beam (left side) 15 A fingerprints on the glass evaporate and 26 Dipped beam (right side) 15 A residue builds up on the reflector eventually resulting in a dull reflector. 27 Parking lamp (left side) 10 A Inadvertently stained bulbs may be 28 Front fog lamps 15 A cleaned with a clean lint-free cloth, using 29 Main beam 15 A alcohol or white spirit. 30 Rear wipers 20 A Replacement bulb must be in accordance 31 --with data on base of defective bulb. Do not exceed wattage given on bulb base. 32 Headlamp washer 20 A Headlamp removal Headlamp aiming For bulb replacement, it is necessary to first 33 Transmission Control 15 A We recommend that headlamp aiming be remove the headlamp assembly. Module carried out by a workshop, which will have 1. Switch off ignition and headlamp switch. 34 Trailer/parking lamp 10 A special equipment. (left side) 2. Open the bonnet, release the 11 When aiming your headlamps, the manual retainers and remove the radiator cover. 35 Spare 25 A headlamp range adjustment 3 must be set 36 Spare 20 A to 7. 3. Remove 3 bolts and withdraw headlamp. 37 Spare 15 A 4. Depress harness connector tags and 38 Spare 10 A disconnect headlamp wiring. 5. Remove the headlamp assembly. Headlamp assembly installation is the reverse of removal - ensure locating dowel aligns with its socket. Do not overtighten bolts or retainers. 186 Self-help, vehicle care
Halogen headlamp system Parking lamps Front turn signal lamps Dipped and main beam 1. Remove headlamp assembly - 1. Remove headlamp assembly - Main beam 1 (inner bulbs) and dipped seepage185. see page 185. beam 2 (outer bulbs). 2. Remove headlamp cap and withdraw 2. Rotate bulb holder anti-clockwise and 1. Remove headlamp assembly - bulb holder (located next to main beam withdraw bulb holder from lamp seepage185. bulb) from lamp assembly. assembly. 2. Remove headlamp cap. 3. Remove bulb from bulb holder by pulling 3. Press and rotate bulb anti-clockwise to it straight out. remove it from bulb holder. 3. Release bulb retaining spring and remove bulb from reflector housing. 4. Install new bulb, using a lint-free cloth to 4. Install new bulb into bulb holder by hold bulb. pressing and rotating it clockwise. 4. When fitting a new bulb, ensure the lugs engage correctly with the recesses on the 5. Reinstall bulb holder in lamp assembly 5. Reinstall bulb holder in lamp assembly reflector. Do not touch the glass. and replace headlamp cap. by rotating it clockwise. 5. Engage bulb retaining spring and 6. Reinstall headlamp assembly. 6. Reinstall headlamp assembly. replace headlamp cap. 6. Reinstall headlamp assembly. Self-help, vehicle care 187
Xenon headlamp system 3 Parking lamps Front turn signal lamps Halogen headlamps A can be identified 1. Remove headlamp assembly - 1. Remove headlamp assembly - from Xenon headlamps B by the different seepage185. see page 185. lens layout. 2. Rotate bulb holder anti-clockwise and 2. Rotate bulb holder anti-clockwise and withdraw bulb holder from lamp withdraw bulb holder from lamp 9 Warning assembly. assembly.
Xenon headlamps operate at very high 3. Remove bulb from bulb holder by pulling 3. Press and rotate bulb anti-clockwise to voltages. Do not touch; risk of fatal injury. it straight out. remove it from bulb holder. Have dipped beam and main beam 4. Install new bulb, using a lint-free cloth to 4. Install new bulb into bulb holder by repaired by a workshop only. hold bulb. pressing and rotating it clockwise. 5. Reinstall bulb holder in lamp assembly 5. Reinstall bulb holder in lamp assembly by rotating it clockwise. by rotating it clockwise. 6. Reinstall headlamp assembly. 6. Reinstall headlamp assembly. 188 Self-help, vehicle care
Front fog lamps Side repeater lamps Rear brake, tail, turn signal, reverse lamps 1. Remove 2 screws from panel on 1. Using a suitable screwdriver, pry lamp and fog tail lamp underside of vehicle below front fog assembly away from wing. 1. Open the tailgate and remove 2 screws lamps and remove panel. 2. Rotate bulb holder anti-clockwise. and lamp assembly. 2. Disconnect harness connector from bulb 3. Remove bulb from lamp assembly by 2. Remove bulb holder by rotating it holder and rotate bulb holder anti- pulling bulb straight out of bulb holder. anti-clockwise. clockwise. 4. Install new bulb into bulb holder by 3. Remove bulb from bulb holder by 3. Remove bulb holder from lamp pressing it in and rotating the bulb pressing the bulb in and rotating it anti- assembly, rotate bulb anti-clockwise and holder clockwise. clockwise. remove from bulb holder. 5. Push lamp assembly back into aperture. 4. Install new bulb into bulb holder. 4. Install new bulb into bulb holder and 5. Reinstall bulb holder into lamp assembly. rotate it clockwise. Rotate bulb holder clockwise and ensure 5. Reinstall bulb holder in lamp assembly it is secure. and reconnect harness connector. 6. Reinstall panel to underside of vehicle using 2 screws removed earlier. Self-help, vehicle care 189
6. Replace lamp assembly by guiding lugs License plate lamps Front reading lamps on lamp assembly into their holes (see 1. Remove 4 screws (arrowed) and remove 1. Using a suitable screwdriver, pry lamp black arrows in illustration). lamp covers. lens away from roof lining. 7. Replace 2 screws removed earlier and 2. Remove bulb holder from lamp assembly 2. Remove bulb. close the tailgate. by rotating it anti-clockwise. 3. Install new bulb. 3. Pull bulb straight out of bulb holder. 4. Reinstall lamp lens in roof lining. 4. Install new bulb. 5. Reinstall bulb holder into lamp assembly, rotate bulb holder clockwise and ensure it is secure. 6. Replace lamp covers using 4 screws removed earlier. 190 Self-help, vehicle care
Rear interior lamps Luggage compartment lamps 3 Front door lamps 1. Using a suitable screwdriver, pry lamp 1. Using a suitable screwdriver, remove lens 1. Using a suitable screwdriver, pry lamp lens away from roof lining. from lamp assembly. lens away from front door trim. 2. Remove bulb. 2. Remove bulb. 2. Remove bulb. 3. Install new bulb. 3. Install new bulb. 3. Install new bulb. 4. Reinstall lamp lens in roof lining. 4. Reinstall lens to lamp assembly. 4. Reinstall lamp lens to front door trim. Self-help, vehicle care 191
Centre high-mounted stop lamp, Never carry out any repairs or adjustment instrument panel and glove compartment and maintenance work on the vehicle illumination yourself. This especially applies to the We recommend having bulb replacements engine, chassis and safety parts. You may, carried out by a workshop. out of ignorance, infringe the provisions of the law and, by not performing the work Opel genuine parts and properly, you may endanger yourself and accessories other road users. We recommend the use of “Opel genuine parts and accessories” and conversion Checking and topping up fluids parts released expressly for your vehicle To aid identification, the engine oil filler type. These parts have undergone special cap, the coolant filler cap, the lid of the tests to establish their reliability, safety and fluid container for the windscreen washer specific suitability for your vehicle. Despite system and the handle of the engine oil continuous market monitoring, we cannot A note on safety gauge (dipstick) may be coloured yellow. assess or guarantee these attributes for other products, even if they have been To avoid the possibility of injury, only carry granted approval by the relevant out engine compartment checks (e.g. authorities or in some other form. checking the brake fluid level or the engine oil level) when the ignition is switched off. “Opel genuine parts and accessories” and conversion parts approved by Opel can be 9 Warning obtained from your Opel Partner, who can provide comprehensive advice about The cooling fan may be operated by a permitted technical changes and ensure thermoswitch and can therefore start to that the part is installed correctly. operate unexpectedly, even when the ignition is switched off; risk of injury. Electronic ignition systems generate very high voltages. Do not touch the ignition system; high voltage can be fatal. 192 Self-help, vehicle care
Engine oil Information on engine oils - see page 213. Engine oil level and consumption It is normal for every engine to consume some oil, and it is sometimes necessary to check and top up the engine oil level between oil changes. 9 Warning
Do not allow the engine oil level to drop below the minimum level.
For this reason, the engine oil level should The illustrations show checking and Engine oil level check and topping up be checked every 500 km (300 miles) or replenishing the engine oil in the Z 24, Z 32 The engine oil level must be checked with before starting a long trip. petrol engines and the Z 20 diesel engines the vehicle horizontal and with the engine respectively. (which must be at operating temperature) To check the level, remove dipstick from switched off. Wait a few minutes before the dipstick tube, wipe it clean and re-insert checking the level to allow the normal oil it as far as it will go. After pulling the accumulation in the engine to drain back dipstick out again, check the oil level, into the oil pan. ensuring it is between the lower and upper (or MIN and MAX) marks. Self-help, vehicle care 193
Top up if the engine oil level has dropped When replenishing, attempt to use the Capacities - see page 225. to the "add oil" lower mark (or MIN mark). same type of engine oil as used at the last A stabilization of the engine oil The oil level must not go above the upper oil change. consumption will not take place until the (or MAX) mark on the dipstick. This would vehicle has been driven several thousand lead, for example, to increased oil kilometres/miles. Only then can the actual consumption, excessive formation of degree of oil consumption be established. carbon residue and a possible risk of If oil consumption exceeds more than damage to the catalytic converter or the 0.6 litres every 1000 km (600 miles) after engine. this running-in period, consult a workshop. 194 Self-help, vehicle care
9 Warning
Used engine oil filters and empty oil containers should not be disposed of as domestic refuse. We recommend that you entrust oil and oil filter changes to a workshop who is familiar with legal requirements regarding disposal of used oil and can thus help to protect both the environment and your health. Engine oil is a danger to health; avoid prolonged contact with skin and wash exposed areas thoroughly. Engine oil change, oil filter change Diesel fuel filter Engine oil changes are to be carried out Remember to reset the engine oil life Drain diesel fuel filter of residual water at depending on time intervals or kilometre/ monitor 3 whenever the engine oil is every engine oil change. mileage intervals, since oil loses its changed. lubrication properties not only through Place a container underneath the filter Engine oil life monitor 3 engine operation but also through ageing. housing. Turn drain plug, located on the The engine oil life monitor lets you know left of the filter housing, anti-clockwise We recommend that you use genuine Opel when to change the oil. Based on driving using a suitable screwdriver, to drain off oil filters. conditions, the kilometre/mileage interval the water. at which an oil change will be indicated can vary considerably. The filter is drained as soon as diesel fuel emerges from the port. Retighten the drain For the system to work properly, it must be plug by turning it clockwise. reset every time the oil is changed. Consult a workshop. With engine switched off, turn ignition key to ON, wait approx. 5 seconds, and turn When the system has calculated that oil life key to LOCK to perform priming operation. has been diminished, control indicator C Perform this operation 3 times or more illuminates in the instrument panel - while the engine is switched off, to avoid air see page 73. Engine oil needs changing entering the fuel line. within approx. 1000 km (600 miles). Engine power may be decreased. Self-help, vehicle care 195
Check diesel fuel filter at shorter intervals if Coolant the vehicle is subjected to extreme During operation, the system is operating conditions such as high humidity pressurized. The temperature may (primarily in coastal areas), extremely high therefore rise to over 100 °C. or low outside temperatures and substantially varying daytime and night- The antifreeze provides excellent corrosion time temperatures. protection for the cooling and heating system, as well as freeze protection down If there is water in the diesel fuel filter, to -28 °C. control indicator N illuminates in the instrument panel - see page 73. Drain the Certain types of antifreeze can lead to water immediately. engine damage. We therefore strongly recommend the use of antifreeze that has been approved by Opel.
9 Warning Coolant level Hardly any losses occur since the cooling Antifreeze is a danger to health: it must system is sealed and it is thus rarely therefore be kept in the original container necessary to top up the coolant. and out of the reach of children. The coolant level in the expansion tank Antifreeze and corrosion protection should be between the MIN and MAX Before the start of the cold weather season, marks when the system is cold. have the coolant checked for correct concentration by a workshop. The amount of antifreeze must provide protection down to approx. –28 °C. If the antifreeze concentration is too low, this reduces protection from freezing and corrosion. Top up antifreeze if necessary. If coolant loss is topped up with demineralised water, have antifreeze concentration checked and more antifreeze added as necessary. 196 Self-help, vehicle care
Coolant temperature 9 Warning Control indicator W illuminates when coolant temperature is too high. Check Allow engine to cool down before coolant level: removing coolant filler cap. If steam is z visible, move away from the vehicle until Coolant level low: the engine is cool. Top up coolant. Pay attention to the instructions given under "Antifreeze and Remove coolant filler cap carefully so corrosion protection" and "Coolant that pressure can escape slowly, level". Have the cause of the coolant loss otherwise there is a risk of scalding. remedied by a workshop. z Coolant level OK: When the engine is at operating Have the cause of increased coolant temperature, coolant level rises. It falls temperature remedied by a workshop. again when the system cools. If it falls below the MIN mark when the system is Brake fluid cold, the coolant must be replenished. Brake fluid level Top up antifreeze. If no antifreeze is 9 Warning available, top up with clean tap water. If tap water is unavailable, distilled water Caution - brake fluid is poisonous and can be used. corrosive. Do not allow it to contact eyes, When you top up with tap water or distilled skin, fabrics or painted surfaces; direct water, add concentrated antifreeze and contact may cause injuries and damage. possibly mix in antifreeze as well. Have the cause of the coolant loss eliminated by a workshop. Too low a coolant level can cause engine damage. When closing, tighten coolant filler cap as far as it will go. Self-help, vehicle care 197
The brake fluid level in the reservoir must Brake fluid change not be higher than the MAX mark or lower As brake fluid is hygroscopic, it absorbs than the MIN mark. water. Vapour bubbles which impair the Do not overfill the brake fluid reservoir, as braking effect may occur during braking. this may cause an engine fire due to fluid The fluid change intervals specified on burning; risk of injury and damage to the pages 206 to 212 must therefore be vehicle. observed. Use of some brake fluids could cause damage or impair braking effectiveness. 9 Warning Stay well informed. We recommend that We recommend that you have brake fluid you use Opel-approved high performance changed by a workshop, who will be brake fluid. familiar with the requirements of the law Extreme cleanliness is important, since as regards disposal of brake fluid and brake fluid contamination can lead to can thus help to protect the environment Clutch fluid 3 brake system malfunctions. and your health. The clutch fluid does not require any If brake fluid level is too low, brake system additional maintenance than that detailed control indicator 4 illuminates in the on pages 206 to 212. instrument panel - see page 70. If the fluid in the reservoir falls below the After correcting the brake fluid level, have MIN mark, consult a workshop. the cause of the loss remedied by a workshop. 198 Self-help, vehicle care
Windscreen wipers Clear vision is essential for safe driving. Perform regular checks on the wipers to ensure they are operating correctly. We recommend wiper blade replacement at least once a year. If the windscreen is dirty, operate the windscreen washer system before switching on the wipers or setting the wipers to automatic operation with the rain sensor 3. This will avoid wiper blade wear. Do not switch on the windscreen wipers if the windscreen is dry or obstructed (e.g. Power steering fluid with snow or ice), as this could damage the To ensure proper operation of the rain The power steering fluid does not require glass, the wiper blades, or the wiper sensor 3, the sensor area must be free from any additional maintenance than that system. dust, dirt and ice, which is why the detailed on pages 206 to 212. If the wipers become frozen on to the glass, windscreen washer system must be operated at regular intervals and the If the fluid in the reservoir falls below the we recommend that they be released with the aid of Opel De-icer Spray. sensor area de-iced. Vehicles with rain MIN mark, consult a workshop. sensor can be identified by the sensor area Smearing wiper blades can be cleaned with near the top of the windscreen. a soft cloth and Opel Cleaning Solvent and Antifreeze. Wiper blades whose lips have become hardened, cracked or covered with silicone must be replaced. This may be necessary as a result of the effects of ice, thawing salt or heat, or the incorrect use of cleaning agents. Switch off the wipers in car washes – see pages 92 and 202. Wiper care – see page 205. Self-help, vehicle care 199
In cold weather, do not fill the windscreen washer fluid reservoir more than three- quarters full, to allow enough room for expansion if the fluid freezes, and to prevent damage to the reservoir. In freezing conditions, use windscreen washer fluid with sufficient antifreezing properties. Do not use coolant antifreeze or tap water, to avoid freezing the solution and damaging the windscreen washer system. When closing the container, press the lid down firmly all the way round. Replacing windscreen wipers Windscreen washer system If the fluid in the windscreen washer fluid reservoir is too low, control indicator G Lift wiper arm, press and hold retaining clip Do not spray washer fluid onto windscreen and detach wiper blade. illuminates in the instrument panel - in freezing weather, to avoid ice forming see page 73. Top up washer fluid as soon and impairing vision. as possible. The filler opening of the fluid container for the windscreen washer system is located in the front of the engine compartment. Fill only with commercially available, ready-to-use windscreen washer fluid. Do not use tap water, as minerals will cause clogging in the system. 200 Self-help, vehicle care
Laying up the vehicle for more than 6 weeks can lead to battery discharge, 9 Warning which may reduce the service life of the battery. Disconnect battery from on-board Ensure there is adequate ventilation power supply by detaching negative when charging the battery. There is a risk terminal (anti-theft alarm system 3 is then of explosion if gases generated during disabled). charging are allowed to accumulate. Ensure that ignition is switched off before Battery acid is poisonous and corrosive. connecting the battery. Then perform the Do not allow it to contact eyes, skin, following actions: fabrics or painted surfaces; direct contact may cause injuries and damage. z Set date and time in the information display - see pages 80, 86. Avoid dealing with the battery near naked flames and anything that would z If necessary, activate the electric generate sparks. No smoking! Battery windows and sun roof 3 - see pages 32, 34. The battery is maintenance-free. Charge a disconnected battery every In order to prevent the battery from 6 weeks. 9 Warning discharging, some consumers such as the courtesy lamps automatically switch off We recommend that you have battery after a delay. changes carried out by a workshop who knows the laws concerning the disposal of used batteries, therefore protecting the environment and your health.
Retrofitted electrical or electronic accessories can place an additional load on the battery or discharge the battery. Consult a workshop regarding technical possibilities, such as fitting a more powerful battery. Self-help, vehicle care 201
Disconnecting/connecting the battery Vehicle care from/to the electrical system In caring for your vehicle, observe all Disconnect the battery from the vehicle national environmental regulations, electrical system before charging: particularly when washing your vehicle. first detach the negative and then the positive lead. Regular, thorough care contributes to improving the appearance of your vehicle Do not reverse the polarity of the battery, and maintaining its value. It is also a i.e. do not confuse the terminals for the prerequisite for claims made under the positive and negative leads. When warranty, in the event of paint or corrosion connecting, start with the positive lead and damage. In the following pages, we give then connect the negative lead. you tips for vehicle care which, with correct use, will help to ward off unavoidable and Vehicle storage harmful environmental influences. If your vehicle is to be stored for long Protection of electronic periods without use, we recommend you components consult a workshop for advice. In order to avoid the breakdown of electronic components within the electrical system, never disconnect the battery with the engine running. Never start the engine while the battery is disconnected (e.g. when using jump leads). To avoid damaging the vehicle, do not make any modifications to the electrical system, e.g. connecting additional consumers or tampering with electronic control units (chip tuning). 9 Warning
Electronic ignition systems generate very high voltages. Do not touch the ignition system; high voltage can be fatal. 202 Self-help, vehicle care
Vehicle care aids 3 Washing Clean edges and folds on opened doors Vehicle wash: The paintwork of your vehicle is exposed to and flaps as well as the areas they cover. z Car Shampoo environmental influences, e.g. continuous Thoroughly rinse off and leather-off the z Sponges changes in weather conditions, industrial vehicle. Rinse leather frequently. Use z Chamois Leather waste gases and dust or thawing salts, so separate leathers for paint and window z Wheel Cleaners wash and wax your vehicle regularly. When surfaces; remnants of wax on the windows z Engine Cleaners using automatic car washes, select a will impair vision. z Glass Cleaners program which includes waxing. Also wash aluminium trim parts, avoiding Exterior care: Bird droppings, dead insects, resin, pollen the use of abrasive materials such as z Touch-up Applicator and the like should be cleaned off automotive or chrome polish, steam or z Spray and Touch-up Paint immediately, as they contain aggressive caustic soap. Washing with water is z Car Polishes/Colour Restorers constituents which can cause paint normally sufficient. z Car Waxes/Sealers damage. z Observe national regulations. Alloy Wheel Cleaner If using a car wash, comply with the z Alloy Wheel Preserver pertinent instructions of the car wash z Metallic Paintwork Wax manufacturer. The windscreen wipers and z Rust Preventative tailgate wipers must be switched off – z Lubricant Sprays see pages 92, 93. Remove detachable rod z Lock Cylinder Grease antenna by unscrewing it. z De-icer Sprays z Tar Removal Spray Do not use high-pressure jet cleaners. z Insect Remover If you wash your vehicle by hand, make z Window Cleaning Spray sure that the insides of the wings are also z Cleaning Solvent and Antifreeze thoroughly rinsed out. Do not use Interior care: household dishwashing liquid, to avoid z Interior/Upholstery Cleaner removing wax from the paintwork. Self-help, vehicle care 203
Waxing Wheels Tar spots Wax your vehicle regularly, in particular Use a pH-neutral wheel cleaning agent to Tar spots must not be removed with hard after it has been washed using clean the wheels. objects, but instead immediately cleaned Car Shampoo and at the latest when water Avoid using abrasive materials and off with Tar Removal Spray. Do not use no longer forms beads on the paintwork, brushes that can damage the finish. Tar Removal Spray on headlamp and otherwise the paintwork will dry out. other exterior lamp bezels. Wheels are painted and can be treated Also wax aluminium trim parts, edges and with the same agents as the body. For alloy Exterior lamps folds on opened doors and flaps as well as wheels, we recommend the use of Alloy Headlamp and other protective lamp the areas they cover. Wheel Preserver. bezels are made of plastic. If they require additional cleaning after the vehicle has Polishing Paintwork damage Polishing is necessary only if the paint been washed, clean them with Repair small areas of paint damage such Car Shampoo. Do not use any abrasive or has become dull or if solid deposits have as stone impacts, scratches etc. become attached to it. caustic agents, do not use an ice scraper, immediately, using an Opel Touch-up and do not clean them dry. Paintwork polish with silicone forms Applicator or Opel Spray and Touch-up a protective film, making waxing Paint before rust can form. If rust has unnecessary. already formed, have the cause remedied Plastic body parts should not be treated by a workshop. Please also pay attention with wax and polish. to surfaces and edges beneath the vehicle where rust may have formed unnoticed for Use Metallic Paintwork Wax on vehicles some time. with a metallic-effect paint finish. 204 Self-help, vehicle care
Plastic and rubber parts Avoid over-exposure to vapours from Seat belts For additional cleaning of plastic and cleaning agents and other chemicals when Always keep seat belts clean and dry. rubber parts, use a cleaner suitable for cleaning. Whenever possible, avoid using Clean seat belts only with lukewarm water vehicle interiors. Do not use any other such cleaning agents in small, unventilated or Interior/Upholstery Cleaner. agent, and in particular do not use solvents spaces, to avoid inhalation of dangerous or petrol. vapours. Open the doors. Periodically check the seat belts and replace immediately with new seat belts if If the front seats are equipped with side Wheels and tyres damage or weakening of the belts has airbags 3, do not use chemical solvents or Do not use high-pressure jet cleaners on occurred. strong detergents on the seat covers. wheels and tyres. Do not saturate the seat covers with Windows Interior and upholstery Interior/Upholstery Cleaner, to avoid When cleaning the heated rear window, Clean the vehicle interior regularly, contaminating the airbag system, make sure that the heating element on the including the instrument panel fascia, otherwise the side airbags 3 may not inside of the window is not damaged. using Interior/Upholstery Cleaner. trigger in the event of a collision. Never place stickers on the inside of the rear window. Clean fabric upholstery with a vacuum cleaner and brush. To remove stains, use a Use a soft, lint-free cloth or chamois cleaner that is suitable for both fabrics and leather, in conjunction with Window vinyl. Cleaning Spray and Insect Remover. Do not use sharp instruments or abrasive cleaners. Open Velcro fasteners on clothing could damage seat upholstery. Make sure that Opel Cleaning Solvent and Antifreeze is Velcro fasteners are closed. suitable for de-icing windows. Do not use cleaning agents such as For mechanical removal of ice, use a acetone, carbon tetrachloride, paint commercially available sharp-edged ice thinner, paint remover, nail varnish scraper. Press the scraper firmly against remover, washing powder or bleach to the glass so that no dirt can get under it clean fabrics, carpets, the instrument panel and scratch the glass. or leather trim 3 in the vehicle interior. Benzine, petrol, naphtha, enamel reducers and lacquer thinners are also unsuitable. Self-help, vehicle care 205
Windscreen wiper blades Engine compartment Underbody Wax, such as that used in car washes, can Areas of the engine compartment that are Your vehicle has a factory-applied PVC cause streaks to form on the windscreen painted in the same colour as the vehicle undercoating in the wheel arches when the wipers are used. must be looked after like any other painted (including the longitudinal members) which Smearing wiper blades can be cleaned with surface. provides permanent protection and needs a soft cloth and Opel Cleaning Solvent and It is advisable to wash the engine no special maintenance. The surfaces of Antifreeze, and replaced if necessary – compartment before and after winter and the vehicle underbody not covered by PVC see page 198. Do not use abrasive preserve it with wax. Cover alternator and are provided with a durable protective wax cleaners. fluid reservoirs with plastic sheets before coating in critical areas. washing the engine. On vehicles which are washed frequently Locks When washing the engine with a steam-jet in automatic car washes with underbody The locks are lubricated with a high-grade cleaner, do not direct the steam-jet at washing facility, the protective wax lock cylinder grease at the factory. Opel components of the Anti-lock Brake System coating may be impaired by dirt-dissolving Lock Cylinder Grease prevents the locks (ABS), the air conditioning system or the additives. Check the underbody after from freezing up. belt drive and its components. washing and have it waxed if necessary. Only use de-icing agents in emergencies, Before the start of the cold weather season, Protective wax that has been applied is as they have a degreasing effect and will check the PVC coating and protective wax also removed during the engine wash. For impair the function of the locks. After using coating and, if necessary, have them this reason, have the engine, brake system a de-icing agent, have the locks re-greased restored to perfect condition. components in the engine compartment, by a workshop. axle components with steering, body parts Caution – commercially available bitumen/ and cavities thoroughly preserved with rubber materials can damage the PVC protective wax after the wash. coating. We recommend that you have underbody work carried out by a An engine wash can be performed in the workshop, who knows the prescribed spring in order to remove dirt that has materials and has experience in the use adhered to the engine compartment, thereof. which may also have a high salt content. Check protective wax layer and make good The underbody should be washed if necessary. following the end of the cold weather season to remove any dirt adhering to the underbody since this may also contain salt. Check protective wax coating and, if necessary, have it restored to perfect condition. 206 Service, maintenance Service, maintenance European service intervals Confirmations Engine oil change - Z 24 XE only Confirmation of Service is recorded in the Due every 15,000 km (10,000 miles). spaces provided in the Service and Main Service Warranty Booklet. The date and kilometre/ European service schedule ...... 207 Due every 30,000 km (20,000 miles) or mileage reading is completed with the International service schedule...... 209 1 year, whichever occurs first. stamp and signature of the Servicing Additional servicing...... 213 Workshop. International service intervals Recommended fluids and lubricants 213 Make sure that the Service and Warranty Interim Service - except Z 24 XE Booklet is completed correctly as Due every 15,000 km (10,000 miles). continuous proof of service is essential if Main Service - except Z 24 XE any warranty or goodwill claims are to be Due every 30,000 km (20,000 miles) or met, and is also a benefit when you come 1 year, whichever occurs first. to sell the vehicle. Interim Service - Z 24 XE only Service plan Due every 10,000 km (6,500 miles) or The European service schedule is valid for 6 months, whichever occurs first. the following countries: Main Service - Z 24 XE only Andorra, Austria, Belgium, Cyprus, Due every 20,000 km (13,000 miles) or Czech Republic, Denmark, Estonia, 1 year, whichever occurs first. Finland, France, Germany, Greece, Greenland, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, The Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, United Kingdom. For all remaining countries the International service schedule applies. Service, maintenance 207
European service schedule (Antara Z 20 DM, Z 20 DMH, Z 24 XE, Z 32 SE)
Service operations by year 1) 1 2 3 km ( x 1000)1) 15 30 45 60 75 90 miles ( x 1000)1) 10 20 30 40 50 60 Controls, lighting, signalling equipment and airbags: visual check xxx steering lock and ignition lock: check Remote control batteries: replace Every 2 years Windscreen wipers, windscreen washer system: check, correct x x x Coolant level and antifreeze: check, correct xxx Hoses: check for tightness and secure seating Brake fluid level: check, correct x x x Battery terminals: check for secure connections and battery eye x x x Vehicle system check with TECH2 x x x Pollen filter: replace x x x o More often for when dust, sand or pollen is in the air Agreement with customer Air cleaner element: replace xxx ⊕ Spark plugs and plug leads: replace Every 90 000 km/60 000 miles Ribbed V-belt: visual check x x x ⊕ Toothed belt and tension roller: visual check x x x Toothed belt and tension roller: replace - Z 24 XE Every 8 years/120 000 km/80 000 miles Toothed belt and tension roller: replace - Z 20 DM, Z 20 DMH Every 6 years/90 000 km/60 000 miles Power steering system: check for leaks. Fluid level: check, correct x x x Engine oil and oil filter: replace - fixed interval Z 24 XE2) xxxxxx Z 20 DM, Z 20 DMH, Z 32 SE, except2) xxx
1) Whichever occurs first. 2) On vehicles with oil life monitoring, it may be necessary to change the engine oil earlier (control indicator illuminates). 208 Service, maintenance
Service operations by year 1) 1 2 3 km ( x 1000)1) 15 30 45 60 75 90 miles ( x 1000)1) 10 20 30 40 50 60 ⊕ Diesel fuel filter: drain water Annually o (If relative humidity is high and/or fuel is of lower quality) Fuel filter: replace and drain water - diesel (grade EN 590) Every 2 years/60 000 km/40 000 miles Parking brake: check and adjust xxx Wheel mounting and suspension front and rear, brake lines, brake pressure hoses, fuel lines and exhaust system: visual check Corrosion protection: check and record in Service and Warranty Booklet Annually Front and rear wheel brakes: check visually x x x o⊕ Annual service check if annual mileage exceeds 20 000 km Annually Engine, transmission, PTO, rear differential, A/C compressor: check for leaks x x x Steering system boots, track rods, final drive: visual check x x x Track rod end and supporting ball joint: check x x x ⊕ Brake and clutch fluid: change Every 2 years Wheel fastening: loosen and tighten to torque xxx Tyre condition and pressures: check, correct ⊕ Annual service check if annual mileage exceeds 20 000 km Annually First aid kit, tyre repair kit and lashing eyes: visual check Every 2 years Headlamp aiming: check, adjust x x x Door hinges, door stop, lock cylinder, lock striker, bonnet catch, tailgate xxx hinges and check links: lubricate Test drive, final check xxx Service interval display and oil life monitor: reset - if applicable
1) Whichever occurs first. ⊕ Additional operations. o Under extreme operating conditions and if required by country-specific conditions, the intervals are reduced. Service, maintenance 209
International service schedule (All except Z 24 XE)
Service operations by year 1) 1 2 3 km ( x 1000)1) 15 30 45 60 75 90 miles ( x 1000)1) 10 20 30 40 50 60 Controls, lighting, signalling equipment and airbags: visual check xxxxxx steering lock and ignition lock: check Remote control batteries: replace Every 2 years Windscreen wipers, windscreen washer system: check, correct x x x x x x Coolant level and antifreeze: check, correct Annually Hoses: check for tightness and secure seating Brake fluid level: check, correct x x Battery terminals: check for secure connections and battery eye Annually Vehicle system check with TECH2 Annually Pollen filter: replace x x x o More often for when dust, sand or pollen is in the air Annually/15 000 km/10 000 miles Air cleaner element: replace xxx o More often for when dust or sand is in the air Annually/15 000 km/10 000 miles ⊕ Spark plugs and plug leads: replace Every 90 000 km/60 000 miles Ribbed V-belt: visual check x x x ⊕ Toothed belt and tension roller: visual check Annually/15 000 km/10 000 miles Toothed belt and tension roller: replace - Z 20 DM, Z 20 DMH Every 6 years/90 000 km/60 000 miles Power steering system: check for leaks. Fluid level: check, correct Annually Engine oil and oil filter: replace x x x x x x
1) Whichever occurs first. 210 Service, maintenance
Service operations by year 1) 1 2 3 km ( x 1000)1) 15 30 45 60 75 90 miles ( x 1000)1) 10 20 30 40 50 60 ⊕ Diesel fuel filter: drain water Annually o (If relative humidity is high and/or fuel is of lower quality) Fuel filter: replace and drain water - diesel (grade EN 590) Every 2 years/60 000 km/40 000 miles Parking brake: check and adjust Every 2 years/60 000 km/40 000 miles Wheel mounting and suspension front and rear, brake lines, brake pressure hoses, fuel lines and exhaust system: visual check Corrosion protection: check and record in Service and Warranty Booklet Annually Front and rear wheel brakes: check visually Every 2 years/60 000 km/40 000 miles o⊕ Annual service check if annual mileage exceeds 20 000 km Annually o⊕ Automatic transmission oil: change Every 4 years/60 000 km/40 000 miles Engine, transmission, A/C compressor: check for leaks Annually Steering system boots, track rods, final drive: visual check Annually Track rod end and supporting ball joint: check Annually ⊕ Brake and clutch fluid: change Every 2 years Wheel fastening: loosen and tighten to torque Every 2 years/60 000 km/40 000 miles Tyre condition and pressures: check, correct ⊕ Annual service check if annual mileage exceeds 20 000 km Annually First aid kit, tyre repair kit and lashing eyes: visual check Every 2 years Headlamp aiming: check, adjust Every 2 years/60 000 km/40 000 miles Door hinges, door stop, lock cylinder, lock striker, bonnet catch, tailgate Every 2 years/60 000 km/40 000 miles hinges and check links: lubricate Test drive, final check xxxxxx Service interval display and oil life monitor: reset - if applicable
1) Whichever occurs first. ⊕ Additional operations. o Under extreme operating conditions and if required by country-specific conditions, the intervals are reduced. Service, maintenance 211
International service schedule (Antara Z 24 XE)
Service operations by month 1) 6 12 18 24 30 36 km ( x 1000)1) 10 20 30 40 50 60 miles ( x 1000)1) 6.5 13 20 26.5 33 40 Controls, lighting, signalling equipment and airbags: visual check xxx steering lock and ignition lock: check Remote control batteries: replace Every 2 years Windscreen wipers, windscreen washer system: check, correct x x x Coolant level and antifreeze: check, correct xxx Hoses: check for tightness and secure seating Brake fluid level: check, correct x x x Battery terminals: check for secure connections and battery eye x x x Vehicle system check with TECH2 x x x Pollen filter: replace Annually/30 000 km/20 000 miles o More often for when dust, sand or pollen is in the air Agreement with customer Air cleaner element: replace Annually/30 000 km/20 000 miles ⊕ Spark plugs and plug leads: replace Every 90 000 km/60 000 miles Ribbed V-belt: visual check x x x ⊕ Toothed belt and tension roller: visual check Annually/30 000 km/20 000 miles Toothed belt and tension roller: replace Every 8 years/120 000 km/80 000 miles Power steering system: check for leaks. Fluid level: check, correct x x x Engine oil and oil filter: replace - fixed interval2) xxxxxx
1) Whichever occurs first. 2) On vehicles with oil life monitoring, it may be necessary to change the engine oil earlier (control indicator illuminates). 212 Service, maintenance
Service operations by month 1) 6 12 18 24 30 36 km ( x 1000)1) 10 20 30 40 50 60 miles ( x 1000)1) 6.5 13 20 26.5 33 40 Parking brake: check and adjust xxx Wheel mounting and suspension front and rear, brake lines, brake pressure hoses, fuel lines and exhaust system: visual check Corrosion protection: check and record in Service and Warranty Booklet Annually Front and rear wheel brakes: check visually x x x Engine, transmission, PTO, rear differential, A/C compressor: check for leaks x x x Steering system boots, track rods, final drive: visual check x x x Track rod end and supporting ball joint: check x x x ⊕ Brake and clutch fluid: change Every 2 years Wheel fastening: loosen and tighten to torque xxx Tyre condition and pressures: check, correct First aid kit, tyre repair kit and lashing eyes: visual check Every 2 years Headlamp aiming: check, adjust x x x Door hinges, door stop, lock cylinder, lock striker, bonnet catch, tailgate xxx hinges and check links: lubricate Test drive, final check xxx Service interval display and oil life monitor: reset - if applicable
1) Whichever occurs first. ⊕ Additional operations. o Under extreme operating conditions and if required by country-specific conditions, the intervals are reduced. Service, maintenance 213
Additional servicing It is recommended to seek technical advice Engine oil quality Additional operations ⊕ on the servicing requirements dependent European specifications on the specific operating conditions of your Additional work is work that is not required GM-LL-A-025: Petrol engines every service but can be performed in vehicle. GM-LL-B-025: Diesel engines conjunction with a regular service. Recommended fluids and without DPF Time allowances for such work are not lubricants ACEA-C3 Diesel engines included in the scope of regular services Only use products that have been tested with DPF and will be charged for additionally. It is and approved. Damage resulting from the more economic if these operations are use of non-approved materials will not be GM General Motors Europe performed as part of a scheduled service covered by the warranty. than having them performed separately. LL Longlife Severe operating conditions o 9 Warning A or B Engine oil quality Operating conditions are classified as specification severe when one or more of the following Operating materials are hazardous and 025 Validity index occurs frequently: must be handled with the appropriate level of care. If consumed, seek medical Opel engine oil meets classifications z cold starts, attention immediately. Do not inhale GM-LL-A-025 and GM-LL-B-025 and is z stop and go, fumes and avoid skin contact. Keep out therefore suitable for both petrol and z trailer/caravan towing, of reach of children. Do not allow diesel engines. z gradients and/or high altitudes, operating materials to contaminate the z poor road surfaces, sewage system, surface water, ground International specifications z sand and dust, water or soil. Dispose of empty containers ACEA-A3: Petrol engines z extreme temperature fluctuations. properly. Always bear in mind that ACEA-B4: Diesel engines Police vehicles, taxis and driving school operating materials are hazardous to without DPF your health. vehicles are also classified as operating ACEA-C3: Diesel engines under severe conditions. with DPF Under severe operating conditions, it may Checking and topping up fluids The above specification is valid only if the be necessary to have certain scheduled see page 191. service interval is reduced to that shown for service work done more frequently than the the international service schedule - scheduled intervals. Engine oil Engine oil is identified by its quality and see pages 209 to 212. For example, if fuel is used that does not also its viscosity. Quality is more important Topping up engine oil comply with required standards, the fuel than viscosity when selecting which engine Oils of different manufacturers and brands filter may need more frequent draining or oil to use. can be mixed as long as you comply with replacement and it may also be necessary the specified engine oil criteria (quality and to change other components more often viscosity). (e.g. spark plugs). 214 Service, maintenance
Not every engine oil available on the Brake and clutch fluid market meets the quality requirements, Only use DOT4 brake fluid. always check the required specification and rating is marked on the container. 9 Warning If engine oil of the required quality is not available, a maximum of 1 litre of ACEA Brake fluid is poisonous! A3/B4 or A3/B3 grade may be used (only once between each oil change). The Over time, brake fluid absorbs moisture viscosity should be of the correct rating. which will reduce braking effectiveness. Use of ACEA A1/B1 and A5/B5 engine oil is The brake fluid should therefore be expressly forbidden, since they can cause replaced at the specified interval. long-term engine damage under certain Brake fluid should be stored in a sealed operating conditions. container to avoid water absorption. Engine oil additives The SAE viscosity rating defines the ability Ensure it does not become contaminated The use of engine oil additives could cause of an oil to flow. When cold, oil is more with fluids containing mineral oil (oil, damage and invalidate the warranty. viscous than when hot. petrol, cleaner) as this can damage the seals and sleeves of the brake system. Engine oil viscosity Multigrade oil is indicated by two figures. SAE 0W-30, 0W-40, 5W-30 or 5W-40 The first figure, followed by a W, indicates 9 Warning low temperature viscosity and the second figure the high temperature viscosity. Due to its corrosive nature, it must not Coolant and antifreeze come in contact with the paintwork. Flush Use antifreeze of recommended any escaped brake fluid with plenty of specification: silicate-free LLC (Long Life water. Coolant). The system is factory-filled with coolant designed for frost protection down to approx. -28 °C. This concentration should be maintained all year-round. Coolant additives intended to give additional corrosion protection or seal against minor leaks can cause function problems. Liability for consequences resulting from the use of coolant additives will be rejected. Technical data 215 Technical data
Vehicle documents, identification plate...... 215 Coolant, brake fluid, oils ...... 216 Engine data...... 217 Performance...... 218 Fuel consumption, CO2 emissions ..... 219 Weights, payload and roof load ...... 221 Tyres ...... 223 Vehicle documents, Information on identification plate1): Electrical system ...... 225 identification plate 1 Manufacturer Capacities ...... 225 The technical data is determined in 2 Trim level Dimensions...... 226 accordance with European Community 3 Colour code standards. We reserve the right to make 4 Type approval number Mounting dimensions of caravan/ modifications. Specifications in the vehicle 5 Vehicle Identification Number trailer towing equipment...... 227 documents always have priority over those 6 Permissible Gross Vehicle Weight given in this manual. 7 Permissible Gross Train Weight The Vehicle Identification Number (VIN) is 8 Maximum permissible front axle load on the vehicle identification plate, 9 Maximum permissible rear axle load attached to the top of the front panel support, visible when the bonnet is open. The vehicle identification plate may also list, in kilograms, the Gross Vehicle Weight (GVW), the Gross Train Weight (GTW) and the maximum front and rear axle loads respectively. Observe these limits when using the full load or towing capacity of your vehicle.
1) The VIN plate on your vehicle may differ from the illustration shown. 216 Technical data
Coolant, brake fluid, oils Engine oils Use approved fluids only. Information on engine oils is available on page 213. Use of unsuitable fluids could cause serious damage to the vehicle.
The Vehicle Identification Number (VIN) is also engraved on the top right-hand side of the bulkhead near the centre of the engine firewall. Engine identifier code and engine number: stamped on the cylinder block under the engine’s exhaust manifold (petrol engines), or the intake manifold (diesel engines). Technical data 217
Engine data Sales designation 2.4 Petrol 3.2 V6 Petrol 2.0 Diesel 2.0 Diesel Engine stamp Z 24 SE 10 HM Z 20 S Z 20 S Engine identifier code Z 24 XE Z 32 SE Z 20 DMH Z 20 DM Number of cylinders 4644 Bore dia. (mm) 87.5 89.0 83.0 83.0 Stroke (mm) 100.0 85.6 92.0 92.0 Piston displacement (cm3) 2405 3195 1991 1991 Max. engine power (kW) 103 167 110 93 at rpm 5200 6600 4000 4000 Torque (Nm) 220 297 320 295 at rpm 2400 3200 2000 2000 Compression ratio 9.6 10.3 17.5 17.5 Fuel type Petrol Petrol Diesel Diesel Cetane requirement (CN) --49 (D)1) 49 (D)1) Octane requirement (RON)2) unleaded 913)4) 913)4) - - or unleaded 953) 953) - - Max. permissible engine speed, continuous operation (rpm) approx. 6200 6700 47505)/45006) 4750 Engine oil consumption (l/1000 km) 0.60.60.60.6
1) Standard high-quality fuels: D = Diesel. 2) Standard high-quality fuels, e.g. unleaded DIN EN 228; value printed in bold: recommended fuel. 3) Knock control system automatically adjusts ignition timing according to type of fuel used (octane number). 4) Use of 91 RON fuel reduces power and torque. If no unleaded Premium fuel is available, 91 RON can be used, taking care to avoid high engine load or full load as well as driving in mountainous terrain with a caravan/trailer load or high payload. 5) Manual transmission. 6) Automatic transmission. 218 Technical data
Performance (approx. km/h / mph) Engine1) Z 24 XE Z 32 SE Z 20 DMH Z 20 DM Maximum speed2) Manual transmission 175/109 - 180/112 174/108 Automatic transmission - 203/126 178/111 -
1) Sales designation - see page 217. 2) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle. Technical data 219
Fuel consumption, CO2 emissions The directive is oriented to actual driving The figures given must not be taken as a practices: Urban driving is rated at guarantee for the actual fuel consumption Directive 80/1268/EEC (last changed 1 approx. /3 and extra-urban driving with of a particular vehicle. by 2004/3/EG) has applied for the 2 measurement of fuel consumption approx. /3 (urban and extra-urban All values are based on the EU base since 1996. consumption). Cold starts and acceleration model with standard equipment. phases are also taken into consideration. The calculation of fuel consumption as The specification of CO2 emission is also a specified by directive 2004/3/EG takes constituent of the directive. account of the vehicle’s kerb weight, ascertained in accordance with these regulations. Optional extras may result in slightly higher fuel consumption and CO2 emission levels than those quoted. To convert l/100 km into mpg, divide 282 by number of litres/100 km. Save fuel, protect the environment – see page 129. 220 Technical data
Fuel consumption (approx. l/100 km), CO2 emission (approx. g/km) Engine1) Z 24 XE Z 32 SE Z 20 DMH Z 20 DM Manual transmission/Automatic transmission urban 13.3/- - /16.4 8.7/10.9 8.8/- extra-urban 7.3/ - - / 8.9 6.8/ 7.3 6.7/- total 9.6/ - - /11.6 7.6/ 8.6 7.5/- CO2 229/- - /278 198/238 200/-
1) Sales designation – see page 217. Technical data 221
Weights, payload and roof load The combined total of front and rear axle Roof load The payload is the difference between the loads must not exceed the permissible The maximum permissible roof load permissible Gross Vehicle Weight (see Gross Vehicle Weight. For example, if the is 100 kg. vehicle identification plate on page 215) front axle load is being fully utilized, the The roof load is the combined weight of the and the EC kerb weight. rear axle can only bear a load that is equal roof rack and the load. to the Gross Vehicle Weight minus the front To calculate the EC kerb weight, enter the axle load. Driving hints – page 127. data from your vehicle below: See the vehicle identification plate on Roof racks, caravan and trailer towing - z Kerb weight from + ...... kg page 215 or the vehicle documents for see page 153, 167. page 222 permissible axle loads. z Weight of heavy + ...... kg accessories The total = ...... kg is the EC kerb weight. Optional equipment and accessories increase the kerb weight and in some cases also the permissible Gross Vehicle Weight, which means that the payload will also change slightly. Note the weights given on the vehicle identification plate. 222 Technical data
Weights (kg), Kerb weights Model Engine1) Kerb weight2)3) Kerb weight3) Manual transmission Automatic transmission Enjoy/Edition Z 24 XE 1805 - Z 32 SE - 1845 Z 20 DMH 1845 1865 Z 20 DM 1845 - Cosmo Z 24 XE 1805 - Z 32 SE - 1845 Z 20 DMH 1845 1865 Z 20 DM 1845 -
1) Sales designation - see page 217. 2) The Gross Train Weight (GTW), along with the Gross Vehicle Weight (GVW) are shown on the VIN plate - see page 215. 3) With driver (75kg) and all fluids (tank 90% full). Technical data 223
Tyres Tyre chains Wheels Restrictions Restrictions Wheel nut tightening torque: 125 Nm. Not all tyres available on the market We recommend the use of Opel-tested currently meet the structural requirements. fine-mesh tyre chains that add no more We recommend that you consult an Opel than 15 mm to the tyre tread and the Partner concerning suitable tyre makes. inboard sides (including chain lock). These tyres have undergone special tests Tyre chains are permitted only on tyres of to establish their reliability, safety and size 215/70 R 16. We recommend you specific suitability for Opel vehicles. consult your Opel Partner. Despite continuous market monitoring, we Further information - see page 152. are unable to assess these attributes for other tyres, even if they have been granted approval by the relevant authorities or in some other form. Further information - see page 149. Winter tyres 3 Tyres of size 235/55 R 18 are not to be used as winter tyres. Tyres of size 215/70 R 16, 235/60 R 17 and 235/65 R 17 may be used as winter tyres. Use of the spare wheel may alter vehicle handling. Obtain a replacement for the faulty tyre as soon as possible, and have the wheel balanced and fitted to the vehicle. Further information - see page 152. 224 Technical data
Tyre pressures in kPa/bar The tyre pressures given are valid for cold Tyre pressure for load of Tyre pressure for full load tyres. The increased tyre pressure resulting up to 4 persons from extensive driving must not be 1) reduced. Engine Tyres Front Rear Front Rear The tyre pressures specified apply to both Z 24 XE, 215/70 R 16, 210/2.1 210/2.1 230/2.3 240/2.4 summer and winter tyres. Z 20 DMH, 235/60 R 17, Always inflate the spare wheel to the tyre Z 20 DM 235/65 R 17, pressure for full load. 235/55 R 18 Further information - see pages 149 to 153. Z 32 SE 215/70 R 162), 210/2.1 210/2.1 230/2.3 240/2.4 235/60 R 17, 235/65 R 17, 235/55 R 18 All T 155/90 R 16 410/4.1 410/4.1 410/4.1 410/4.1 (temporary spare)3)
1) Sales designation - see page 217. 2) Only permitted as winter tyres. 3) For notes on the temporary spare wheel - see pages 153, 178. Technical data 225
Electrical system
Engine1) Z 24 XE Z 32 SE Z 20 DMH Z 20 DM Battery Voltage12 V12 V12 V12 V Amp hours 60 Ah 70 Ah 90 Ah 90 Ah Battery for radio frequency CR 2032 or CR 2032 or CR 2032 or CR 2032 or remote control equivalent equivalent equivalent equivalent
1) Sales designation - see page 217.
Capacities (approx. in litres)
Engine1) Z 24 XE Z 32 SE Z 20 DMH Z 20 DM Engine coolant 9.0 10.0 9.0 9.0 Fuel tank 65 65 65 65 Engine oil with filter change 4.7 7.4 6.2 6.2 Engine oil between MIN and MAX on dipstick 1.0 1.0 1.0 1.0 Washer fluid reservoir for windscreen and tailgate 4.0 4.0 4.0 4.0 washer system Washer fluid reservoir for windscreen, headlamp 6.7 6.7 6.7 6.7 and tailgate washer system
1) Sales designation - see page 217. 226 Technical data
Dimensions
Overall length (mm) 4576 Width (mm) 1850 Overall height with roof rails (mm) 1747 Wheelbase (mm) 2707 Track width (mm): Front 1562 Rear 1572 Turning circle diameter, wall to wall (m) 12.78 Maximum wading depth (mm) 450 (at 5 km/h (3 mph)) Approach angle 24° Ramp angle 17.6° Departure angle 23° Technical data 227
Mounting dimensions of caravan/ trailer towing equipment Dimension mm A 416 B 507 C 482 D 734 E 1039 F (fully laden) 353 G (at kerb weight) 446
9 Warning
Only use towing equipment approved for your vehicle. We recommend entrusting fitting of towing equipment at a later date to a workshop. 228 Index
Automatic anti-dazzle interior mirror ... 32 Index A Automatic dipped beam activation ...... 95 ABS ...... 148 Automatic level control ...... 97, 143 Accessories ...... 45, 57, 69, 169, 191, 200 Automatic transmission ...... 18, 115 Accessory sockets ...... 69 Automatic mode ...... 116 Active Rollover Protection (ARP) ...... 138 Engine braking assistance ...... 118 Air conditioning system ...... 103, 109 Fault ...... 120 Air distribution ...... 106 Interruption of power supply ...... 120 Air intake ...... 114 Kickdown ...... 117, 118 Air quality sensor ...... 112 Manual mode ...... 117 Air recirculation mode ...... 109 Rocking the vehicle ...... 119 Air vents ...... 104 Selector lever ...... 116 Airbags ...... 42, 52, 54, 55 Transmission display ...... 116 Alarm ...... 29 Winter program ...... 117 Alarm system ...... 27 All Wheel Drive (AWD) ...... 121 B Alternator ...... 74 Battery ...... 200 Antenna ...... 101, 202 Interruption of power supply ...... 120 Antifreeze ...... 195, 214 Battery discharge protection ...... 100 Antifreeze protection ...... 195, 199 Before starting-off ...... 18 Anti-knock quality of fuel ...... 131 Belt force limiters ...... 44 Octane number ...... 217 Belt tensioners ...... 44 Anti-lock Brake System (ABS) ...... 148 Belts ...... 8, 42, 43, 204 Anti-theft alarm system ...... 27 Bleeding, diesel fuel system ...... 171 Anti-theft locking system ...... 27 Board information display ...... 76, 78 Towing equipment ...... 166 Bonnet ...... 171 Approach lighting ...... 94 Boot, see Luggage compartment ...... 41 Aquaplaning ...... 151 Brake assist ...... 146 Armrests ...... 40, 42 Brake fluid ...... 214 Ashtrays ...... 67 Brake system ...... 145 Illumination ...... 100 Assist grips ...... 69 Automatic air recirculation ...... 112 Automatic anti-dazzle exterior mirrors .31 Index 229
Brakes ...... 145 Clock ...... 76 Fog tail lamp ...... 73, 96 ABS ...... 148 Clutch fluid ...... 197 Front fog lamps ...... 73, 96 Brake assist ...... 146 Clutch operation ...... 128 Front passenger’s seat belt reminder 46 Brake fluid ...... 196 CO2 emissions ...... 219 Fuel level ...... 72, 76 Brake lamps ...... 188 Coin storage ...... 67 Headlamp main beam ...... 73, 95 Brake servo unit ...... 127 Cold starts ...... 128, 133 Park pilot ...... 71, 143 Foot brake ...... 146 Colour information display ...... 77, 83 Power steering ...... 73 Hand brake ...... 147 Console box ...... 65 Preheating ...... 73 Bulb replacement ...... 185 Console net ...... 66 Tailgate ...... 72 Bulbs ...... 185 Contrast ...... 87 Trailer ...... 70 Control indicators ...... 12, 70 Transmission electronics ...... 72 C ABS ...... 70, 148 Turn signal lamps ...... 72 Capacities ...... 225 Airbags ...... 56, 72 Water in diesel fuel ...... 73, 195 Car Pass ...... 21 All Wheel Drive ...... 71, 121 Windscreen washer fluid ...... 73, 199 Caravan/trailer towing ...... 127, 167 Alternator ...... 74 Winter program ...... 74, 117 Card holder ...... 67 Anti-theft alarm system ...... 28, 29, 74 Coolant ...... 195, 214, 216 Care ...... 201 Automatic headlamp Coolant level ...... 195 Catalytic converter ...... 133, 135, 172 range adjustment ...... 71, 97 Coolant temperature ...... 71, 195 Central locking switch ...... 25 Automatic transmission ...... 120 Cooled glove compartment ...... 105 Central locking system ...... 25 Belt tensioners ...... 45, 72 Cooling ...... 110, 111 Centre high-mounted stop lamp Brake system ...... 70, 147, 197 Correcting time ...... 86 Bulb replacement ...... 191 Change engine oil ...... 73, 194 Corrosion protection ...... 214 Changing the battery Coolant temperature ...... 71, 196 Coupling socket load ...... 168 Remote control ...... 24 Cruise control ...... 73, 140 Courtesy lamps ...... 98 Changing tyre/wheel type ...... 149 Descent Control System ...... 71, 138, 139 Bulb replacement ...... 189 Changing wheels ...... 178 Diesel particle filter ...... 73, 135 Switching off ...... 99 Chassis number, see Vehicle Doors ...... 72 Cruise control ...... 140 Identification Number ...... 215, 216 Driver’s seat belt reminder ...... 72 Curtain airbags ...... 55 Check control ...... 91 Electronic immobiliser ...... 22, 72 Child restraint system ...... 47, 58 Electronic Stability Control ...... 71, 136 Child safety locks ...... 30 Engine electronics ...... 72, 134 Cigarette lighter ...... 68 Engine oil level ...... 73 Cleaning ...... 201 Engine oil pressure ...... 74 Climate control ...... 103 Exhaust ...... 74, 134 230 Index
Electrically adjustable front seat ...... 37 D Electronic Climate Control ...... 17, 103, 111 F Dashboard - see Instrument panel ...... 10 Electronic components ...... 201 Fan ...... 106, 191 Data ...... 21, 215 Electronic immobiliser ...... 22 Filling station Date ...... 80 Electronic Stability Control (ESC) ...... 136 Capacities ...... 225 Daytime running lamps ...... 94 Engine braking assistance ...... 118 Engine oil level ...... 192 DCS (Descent Control System) ...... 138 Engine code ...... 216, 217 Fuel ...... 131, 217 Demisting and defrosting Engine control indicator ...... 134 Ignition key ...... 21 Windows ...... 17 Engine data ...... 217 Opening the bonnet ...... 171 With air conditioning system ...... 108 Engine oil ...... 213 Tyre pressure ...... 130, 224 With Electronic Climate Control ...... 113 Additives ...... 214 Vehicle data ...... 215 Descent Control System ...... 138 Topping up ...... 213 Windscreen washer system ...... 199 Diesel ...... 131 Viscosity ...... 214 First aid kit ...... 68, 177 Diesel fuel filter ...... 194 Engine oil change ...... 194 Flat tyre ...... 177 Diesel fuel system ...... 171, 194 Engine oil filter change ...... 194 Flex-Fix system ...... 154 Diesel particle filter ...... 73, 135 Engine oil level and consumption ...... 192 FlexOrganizer ...... 62 Dipped beam ...... 14, 95 Engine oil life monitor ...... 73, 194 Fog tail lamp ...... 96 Bulb replacement ...... 186 Engine oil pressure ...... 74 Bulb replacement ...... 188 Display ...... 76 Engine oils ...... 192, 216 Fold in exterior mirrors ...... 9, 30 Display mode ...... 87 Engine speed ...... 75 Foot brake ...... 146 Door locks ...... 6, 205 Engine wash ...... 205 Front airbags ...... 52 Doors ...... 72 Environmental protection ...... 194, 201 Front door lamps ...... 100 Drink holders ...... 67 ESC (Electronic Stability Control) ...... 136 Bulb replacement ...... 190 Drive control systems ...... 136 Exhaust control indicator ...... 134 Front fog lamps ...... 96 Driving abroad ...... 100 Exhaust gases ...... 135 Bulb replacement ...... 188 Driving hints ...... 127 Exhaust system ...... 135 Front passenger’s seat airbag ...... 52 Front passenger’s seat undertray ...... 66 E Exterior lamps ...... 94 Exterior mirrors ...... 30 Front reading lamps Economical driving ...... 129 Bulb replacement ...... 189 Electric exterior mirrors ...... 9, 30 Front seat armrest ...... 40 Electric sun roof ...... 34 Fuel ...... 131 Electric windows ...... 32 Fuel consumption ...... 129, 131, 219 Child safety system ...... 33 Fuel filler cap ...... 132 Safety function ...... 33 Fuel filter ...... 194 Electrical system ...... 181 Index 231
Fuel gauge ...... 76 Headlamp washer system ...... 16, 93, 199 Fuel system, diesel ...... 194 Antifreeze protection ...... 199 I Fuse extractor ...... 182 Capacities ...... 225 Identification plate ...... 215 Fuses ...... 181 Washer fluid reservoir ...... 199 Ignition logic ...... 80, 87 Headlamps ...... 13, 94 Ignition switch ...... 13 G Bulb replacement ...... 186, 187 Illumination ...... 100 Gears ...... 17 Daytime running lamps ...... 94 Ignition system ...... 19 Generator, see Alternator ...... 74 Driving abroad ...... 100 Immobiliser ...... 22 Glasses compartment ...... 65 Front fog lamps ...... 96 Information display ...... 76 Glove compartment ...... 64 Warning device ...... 92, 94 Bulb replacement ...... 191 Bulb replacement ...... 191 Wiper activated lighting ...... 94 Illumination ...... 98 Cooling ...... 105 Heated exterior mirrors ...... 16, 105 Infotainment system ...... 101, 102 Lighting ...... 64, 100 Heated front seats ...... 105 Inspection system ...... 206 Graphical information display ...... 77, 83 Heated rear window ...... 16, 105 Instrument display ...... 75 Gross Vehicle Weight ...... 131, 167, 221 Heating ...... 103, 107 Bulb replacement ...... 191 Exterior mirrors ...... 105 Illumination ...... 98 H Instrument panel ...... 10 Halogen headlamp system ...... 185 Rear window ...... 105 Seats ...... 105 Instruments ...... 70 Bulb replacement ...... 185 Interior lamps ...... 98 Hand brake ...... 19, 147 With air conditioning system ....107, 108 With Electronic Climate Control 112, 113 Front reading lamps ...... 99 Hazard warning lamps ...... 14, 97 Rear interior lamps ...... 99 Head restraints ...... 8, 39 Heating the footwell ...... 108 Height adjustment Interior mirror ...... 9, 31 Active head restraints ...... 39 Interruption of power supply ... 83, 90, 120 Head restraint position ...... 39 Head restraints ...... 8, 39 Seat belts ...... 47 Selector lever lock ...... 120 Height adjustment ...... 39 ISOFIX ...... 50, 51, 52 Headlamp aiming ...... 185 Steering wheel ...... 13 Headlamp flash ...... 14, 95 High-pressure cleaners 143, 167, 202, 204 J Headlamp main beam ...... 14, 95 Horn ...... 15 Jack ...... 176 Bulb replacement ...... 186 Hydraulic Brake Assist (HBA) ...... 138 Jump leads ...... 172 Control indicator ...... 73, 95 Headlamp range adjustment ...... 97, 185 Automatic ...... 97 Manual ...... 97 Headlamp switch ...... 13, 94 232 Index
Luggage compartment cover ...... 59 K O Lumbar support ...... 7, 37 Octane numbers ...... 217 Key ...... 21 Odometer ...... 75 Extending ...... 21 M Oil ...... 213 Ignition lock ...... 13 Main beam ...... 14, 95 Additives ...... 214 Locking doors ...... 27, 28 Bulb replacement ...... 186 Topping up ...... 213 Removing ...... 92 Control indicator ...... 73, 95 Viscosity ...... 214 Replacement keys ...... 21 Maintenance Oil change ...... 194 Starting ...... 13, 19 Air conditioning ...... 114 Oil filter change ...... 194 Kickdown ...... 117, 118 All Wheel Drive (AWD) ...... 126 Oil level and consumption ...... 192 Antifreeze protection ...... 195 Oil life monitor ...... 73, 194 L Battery ...... 200 Oil pressure ...... 74 Language selection ...... 80, 86 Brake fluid ...... 196 Oils ...... 192, 216 Lashing eyes ...... 61 Brakes ...... 145 Opel Service ...... 206 Leather trim ...... 204 Catalytic converter ...... 135 Operating temperature ...... 128 Level control system ...... 97, 143 Clutch fluid ...... 197 Outside temperature ...... 77, 78 License plate lamps Electronic Climate Control ...... 114 Overrun ...... 128 Bulb replacement ...... 189 Engine oil ...... 192 Light switch ...... 13, 94 Exhaust ...... 135 P Lighting ...... 94 Fuel consumption ...... 130 Paintwork damage ...... 203 Driving abroad ...... 100 Power steering fluid ...... 198 Park pilot ...... 142 Loading ...... 63, 168, 221 Tyre pressure ...... 150 Parking ...... 20, 119 Locking doors ...... 25, 28 Tyres ...... 150 Parking lamps Locking from the inside ...... 25 Windscreen wipers ...... 198 Bulb replacement ...... 186, 187 Locks ...... 205 Manual transmission ...... 17 Parking on inclines ...... 170 Lubricants ...... 191, 216 Mechanical anti-theft locking system ... 27 Payload ...... 221 Luggage compartment Mirrors ...... 9, 16, 30, 31, 105 Pedals ...... 128 Bulb replacement ...... 190 Misted windows ...... 108, 113 Performance ...... 218 FlexOrganizer ...... 62 Mobile telephones ...... 102 Peripheral lighting ...... 98 Lighting ...... 100 Muffler, see Exhaust system ...... 135 Petrol ...... 131, 217 Loading ...... 63, 221 Pinking ...... 131 Locking ...... 26 N Pollen filter ...... 114 Safety net ...... 60 Navigation system ...... 86, 102 Power outlets ...... 68 Storage ...... 63 Neutral ...... 17, 18 Under floor storage ...... 63 Index 233
Power steering ...... 73, 127 Running-in ...... 127 Side repeater lamps Fluid ...... 198 Brakes ...... 145 Bulb replacement ...... 188 Preheating ...... 19, 73 Slide/tilt sun roof ...... 34 Pushing, towing ...... 172 S Spare keys ...... 21 Safeguard against Spare wheel ...... 153, 177 R unauthorised use ...... 13, 20, 21 Speed ...... 129, 130 Radio ...... 101 Safety ...... 191 Fuel consumption ...... 129 Radio equipment (CB) ...... 102 Safety accessories ...... 47, 68, 177 Speedometer ...... 75 Radio frequency remote control Safety net ...... 60 Starting on inclines ...... 170 Central locking system ...... 6, 23, 25 Saving energy ...... 129 Starting the engine ...... 13, 19 Fault ...... 24 Saving fuel ...... 129 Self-help ...... 172 Radio reception ...... 101 Seat adjustment ...... 7, 36 Steam-jet cleaners ...... 143, 167, 202, 204 Rain sensor ...... 15, 93, 198 Seat belts ...... 8, 42, 43, 204 Steering column lock ...... 13 Rear interior lamps Driver’s seat belt reminder ...... 72 Steering wheel adjustment ...... 13 Bulb replacement ...... 190 Front passenger’s seat belt reminder 46 Steering wheel remote control ...... 101 Rear lamp cluster ...... 96 Height adjustment ...... 47 Storage ...... 59 Bulb replacement ...... 188 Removing ...... 47 Stowage compartments ...... 64 Rear seat armrest ...... 42 Seat height adjustment ...... 8, 37 Sun roof ...... 34 Rear seats ...... 41 Seat position ...... 38 Sun visors ...... 34 Folding backrests ...... 41 Seats ...... 7, 36 Illumination ...... 100 Restoring backrests ...... 42 Adjustment ...... 7, 8, 36 Sunglass holder ...... 65 Rear window washer system ....16, 93, 199 Electric seat adjustment ...... 37 System settings ...... 79, 85 Rear window wipers ...... 16, 93 Folding passenger’s seat ...... 40 Refuelling ...... 132 Heated seats ...... 105 T Fuel filler cap ...... 132 Selector lever ...... 18, 116 Tachometer ...... 75 Remote control Selector lever lock ...... 18, 116 Tail and brake lamps Central locking system ...... 6, 23, 25 Self-diagnosis ...... 45 Bulb replacement ...... 188 Fault ...... 24 Self-help ...... 171 Tailgate ...... 6, 26 Replacement keys ...... 21 Automatic transmission ...... 120 Tailgate washer system ...... 16, 93, 199 Reversing lamps ...... 96 Information display ...... 80, 86 Antifreeze protection ...... 199 Bulb replacement ...... 188 Remote control ...... 24 Capacities ...... 225 Roof load ...... 35, 64, 127, 153, 221 Service ...... 206 Washer fluid reservoir ...... 199 Roof racks ...... 130, 153 Service intervals ...... 206, 207 Tailgate wiper ...... 16, 93 Side airbags ...... 54 234 Index
Tank V Winter operation Fuel gauge ...... 76 Valve cap key ...... 150 Battery ...... 128 Technical data ...... 215 Vehicle care ...... 201 Coolant, antifreeze ...... 195 Telephone, see Mobile telephones ...... 102 Vehicle Identification Number .....215, 216 Fuel consumption ...... 130 Temperature regulation ...... 106, 112 Vehicle keys, see Key ...... 21 Fuel for diesel engines ...... 131 Temporary spare wheel ...... 153, 177 Vehicle tools ...... 176 Heating ...... 103, 109, 111 The first 1000 km ...... 127 Vehicle weights ...... 222 Locks ...... 205 Tightening torque ...... 223 Ventilation ...... 103, 104, 107 Tyre chains ...... 152, 223 Time ...... 80, 85 Window demisting Tools ...... 176 W and defrosting ...... 108, 113 Towing ...... 127, 169, 174, 175 Warning buzzers ...... 92 Windscreen wash system, Towing equipment ...... 164, 227 Warning messages ...... 79, 84 antifreeze protection ...... 199 Towing eye ...... 174, 175 Warning triangle ...... 68, 177 Winter tyres ...... 152 Towing service ...... 175 Washer fluid reservoir ...... 199 Winter program ...... 117 Trailer Stability Assist (TSA) ...... 138 Washing the vehicle ...... 202 Winter tyres ...... 152 Trailer/caravan towing ...... 127, 167 Weights ...... 221 Transmission display ...... 76, 116 Wheel condition ...... 150 X Tread depth ...... 151 Wheel trims ...... 152 Xenon headlamp system ...... 97, 187 Trip computer ...... 81, 88 Wheels, tyres ...... 149 Bulb replacement ...... 187 Trip odometer ...... 75 Windows ...... 16, 32, 105 Turn signal lamps ...... 14, 95 Demisting and defrosting ...17, 108, 113 Bulb replacement ...... 186, 187 Windscreen washer system ...... 16, 93, 199 Tyre chains ...... 152 Antifreeze protection ...... 199 Tyre condition ...... 150 Capacities ...... 225 Tyre pressure ...... 150, 168 Washer fluid reservoir ...... 199 Tyre pressure monitoring system ...91, 144 Windscreen wipers ...... 15, 92, 198 Tyres ...... 223 Directional tyres ...... 178 Pressure ...... 224 U Units of measure ...... 81, 87 Unleaded fuel ...... 131, 133, 217 Used engine oil ...... 194