Laboratory the Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Location 1: S. No. 102, Vetal Hill,Off.Paud Road, Kothrud, Pune, Maharashtra Location 2: Plot No. E1/1, MIDC Chakan Industrial Area, Phase-III, Village Nighoje-Mahalunge,Kharabwadi, Taluka-Khed, Pune, Maharashtra Accreditation Standard ISO/IEC 17025: 2005 Certificate Number TC-5085 Page 1 of 64

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed

CHEMICAL TESTING

LOCATION 1

I. PETROLEUM AND PRODUCTS

1. Hydraulic Brake Appearance & Colour IS 8654-2001(RA 2016) Fluid Water content (%m/m) IS 8654-2001(RA 2016) 0.5 % to 10 % Max SAEJ1703-(2012) SAEJ1704-(2012) FMVSS 116-(2018) Equilibrium Reflux IS 8654-2001 (RA 2016) 170 °C to 300 °C Boiling point (ERBP) SAEJ1703-(2012) SAEJ1704-(2012) FMVSS 116-(2018) Wet Equilibrium IS 8654-2001(RA 2016) 100 °C to 220 °C Reflux Boiling point SAEJ1703-2012 (Wet ERBP) SAEJ1704-(2012) FMVSS 116-(2018) Evaporation Test IS 8654-2001(RA 2016) 5 % to 99 % FMVSS 116-(2018) Stability IS 8654-2001(2016) Change in ERBP High Temperature SAEJ1703-2012 Upto 10 °C Chemical SAEJ1704-(2012) FMVSS Upto 10 °C 116-(2018) Corrosion Test IS 8654-2001(RA 2016) 0.01 mg/cm2 to 2 mg/cm2 SAEJ1703-(2012) SAEJ1704-(2012) FMVSS 116-(2018)

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed pH IS 8654-2001(RA 2016) 5 to 13 SAEJ1703-(2012) SAEJ1704-(2012) FMVSS 116-(2018) Water tolerance IS 8654-2001(RA 2016) Bubble flow time SAEJ1703-(2012) 2 sec to 60 sec SAEJ1704-(2012) FMVSS 116-(2018) Fluidity and IS 8654-2001(RA 2016) Bubble flow time appearance SAEJ1703-2012 2 sec to 60 sec SAEJ1704-(2012) FMVSS 116-(2018) Compatibility IS 8654-2001(RA 2016) Visual Appearance SAEJ1703-(2012) SAEJ1704-(2012) FMVSS 116-(2018) Resistance to IS 8654-2001(RA 2016) Change in mass Oxidation SAEJ1703-(2012) 0.01 mg/cm2 to 2 mg/cm2 SAEJ1704-(2012) FMVSS 116-(2018) Effect on rubber IS 8654-2001(RA 2016) Diameter change SAEJ1703-(2012) 0.01 mm to 5 mm SAEJ1704-(2012) FMVSS Hardness change 116-(2018) Upto 15 IRHD Volume change 0.05 % to 25 % 2. Antifreeze Density IS 5759-2006 (RA 2018) 1.100 g/cm3 to 1.150 g/cm3 Coolant ASTM D1122-2016 JISK 2234-2006

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Water content ASTM D1123-1999(2015) 0.5 % m/m to 10 % m/m IS 5759-2006 (RA 2018) JISK 2234-2006 ASTMD 4377-(00)2006 pH Value ASTM D1287-2011 5 to 12 IS 5759-2006(RA 2018) JISK 2234-2006 Boiling Point IS 5759-2006(RA 2018) 100 °C to 200 °C JISK 2234-2006 ASTM D1120-2011 Foaming Properties IS 5759-2006(RA 2018) Upto 10 ml JISK 2234-2006 ASTM D4921-95 (2006) Reserve Alkalinity IS 5759-2006(RA 2018) 0.2 ml to 25 ml of JISK 2234-2006 0.1N HCl ASTM D1121-2011 Corrosion Property of IS 5759-2006(RA 2018) 0.05 mg/cm2 to 10 mg/cm2 Cast Aluminum at Heat JISK 2234-2006 Transfer Surface Glassware Metal IS 5759-2006(RA 2018) 0.005 mg/cm2 to 6 mg/cm2 Corrosion Property JISK 2234-2006 Circulating Corrosion IS 5759-2006(RA 2018) 0.005 mg/cm2 to 6 mg/cm2 Property JISK 2234-2006

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed II. RUBBER AND RUBBER PRODUCT

1. Rubber Polymer identification ASTM D3677-2010e1 Wave No. by FT-IR Spectrometer AIS-066-2004 4000 cm-1 to 400 cm-1 Flammability/Burning SAEJ369:2007 Upto 600 mm/min Behavior FMVSS 302-2018 ISO 3795-1989(E) IS 15061:2002 (2017) (Annex. A)

III. PLASTICS & PLASTIC PRODUCTS

1. Plastic Polymer identification ASTM D3677-2010e1 Wave No. by FT-IR Spectrometer AIS-066-2004 4000 cm-1 to 400 cm-1 Flammability/Burning SAEJ369:2007 Upto 600 mm/min Behavior FMVSS 302-2018 ISO 3795-1989(E) IS 15061:2002 (2017) (Annex. A)

IV. ATMOSPHERIC POLLUTION

1. Vehicle 4 wheeler, A) Tailpipe emissions MoRTH/CMVR/TAP/115- 3 wheeler and CO 116 (Issue4, Amendment 8) 10 mg/km to 20 g/km 2 wheeler vehicles HC GSR 493(E), GSR 400(E), 0.6 mg/km to 5 g/km NOX GSR 77(E), GSR 720(E), 1 mg/km to 2 g/km CH4 GSR 686(E), GSR 853(E), 0.6 mg/km to 1 g/km

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed CO2 GSR 284(E), GSR 589(E), 1 g/km to 500 g/km GSR 786(E), GSR 84 (E), Fuel Consumption GSR 515 (E), GSR 111(E), 2 km/l to 30 km/l (calculated from CO, GSR103(E), GSR431(E), HC, CO2) GSR487(E), GSR498(E), Particulate Matter GSR99(E), GSR412(E), 0.000001mg/km to 0.5 g/km Particulate Number GSR682(E), GSR629(E), 1x106 to 9x1015 number/km B) Idling Emission GSR889(E), GSR954 (E), Measurement GSR290(E), GSR490(E) CO GSR518(E), GSR1461(E), Upto 10% GSR400(E), GSR84(E), HC Upto10000 ppm (V)(C6) GSR103(E), GSR498(E), -1 -1 C) Free Acceleration GSR99(E), GSR412(E), 0.001 m to10 m Smoke GSR 682(E), GSR 954 (E), D) Crankcase GSR 889(E), Qualitative emissions

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed E) Evaporative R83-07(Except Type VI), 0.01 g/test to 30 g/test emissions (HC) R-101, R40, R47 (Volume of SHED ADR79/05 (Except Type VI) Facility is 87.48±13 EEC70/220, (EC)715/2007, (EU)2017/1151, (EU)2017/1154, (EU) 2017/1347 (Except Type VI), GTR02, 97/24/EC (Chapter5), (EU)168/2013 supplemented by (EU)134/2014 and (EU) 44/2014, (EU)2018/295 CARB 2001 for EVAP only, Colombian Decree 910, Indonesian Decree 141of 2003, TRIAS31-J044(1)-01, TRIAS31-J044(2)-01, EPA CFR 40 Part86-Sub Part E&F (Only for 2W), GB15744-2008, GB20998- 2007, GB14621-2011, GB14622-2007 2. Engine A) Pollutants MoRTH/CMVR/TAP/ (measured on steady 115-116 Issue 4 state cycles and Amendment 5, R-49- transient test cycles) 02 to R 49-06, 88/77/EEC CO as amended 2001/27/EC, 10 mg/kWh to 25 g/kWh HC 2005/55/EC as amended 10 mg/kWh to 25 g/kWh

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed NOX 2005/78/EC, (EU) no. 10 mg/kWh to 25 g/kWh

CH4 595/2009 as amended by 10 mg/kWh to 10 g/kWh Particulate Matter (EU) no. 4 mg/kWh to 2 g/kWh 133/2014. AIS 137 Part-4, NH3 0.1 ppm to 1000 ppm AIS 137 Part-7 CO2 10 mg/kWh to 1000 g/kWh ADR80/03, 97/68/EC as amended 2012/46/EU, R 96-04, 2000/25/EC as amended 2014/43, 40 CFR Part 89Sub-Part E, 40 CFR Part 86 Sub-Part N, GSR 286(E), GSR 83 (E), GSR 853(E), GSR 686(E), GSR 284(E), GSR 589(E), GSR276(E), GSR720(E), GSR 84(E), GSR 412(E), GSR 889(E), GSR 498(E)_ 2015, GSR Particulate Number 412(E) 2016, GSR 201(E) 1 X 106 to 9X 1015 Number /kWh B) Measurement of R-85-00 2 kW to 20 kW Engine Power (for CI & SI engines only), 15 kW to 150 kW 80/1269/EEC as amended 22 kW to 220 kW 1999/99/EC, R 120-01, 25 kW to 250 kW ADR30/01, IS14599:1999. 50 kW to 500kW AIS 137 Part-5, Part-7 B) Measurement of UNECE-R24-03, 0.001 m-1 to 10 m-1 visible Pollutant 72/306/EEC (Smoke density) as amended by

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 2005/21/EC,77/537/EEC as amended by 97/54/EEC, GSR 103(E), IS 8118:1998, 40 CFR Part 86 Sub Part I, AIS 137 Part-5, Part-7 3. Off‐road Emission of pollutants 80/1269/EEC as amended 15 kW to 150 kW diesel Engines from diesel engines by 1999/99/ EC, ECER‐120 (Agricultural i) Power Rev.1, ECER‐ 24 Rev 2 Tractor engines, amend. 3, ADR30/012006 Genset engines, MoRTH/CMVR/TAP/ CEV engines) 115‐116 Issue 4 Amendment ‐1 (Part IV), Central Pollution Control Board, GSR771(E), GSR232(E) ii) Free acceleration, 77/537/EEC as amended 0.1 % to100 % Full load & 80%Smoke by 97/54/EC (0.001 m-1 to 10 m-1) MoRTH/ CMVR/TAP/115‐ 116 Issue 4Amendment ‐1 (Part IV), Central Pollution Control Board, GSR 771(E), GSR232(E), ISO 8178‐3:1994 iii) Pollutants 97/68/EC as amended by (measured on steady 2012/46/EU (for Non‐Road state cycles) Steady Cycle only), 2000/25/EC as amended by CO: 0.01g/kWh to CO, 2014/43/EU, ECE R‐96 25 g/kWh

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Rev3 Amend.1 (Annex4A, for Non‐Road HC: 0.01g/kWh to HC, Steady Cycle only), 25 g/kWh MoRTH/CMVR/TAP/115‐116 Issue 4 Amendment ‐1 NOx:0.01g/kWh to 25 NOx, Part XV, Sub‐ Part A, g/kWh (Agri Tractors Stage III A and CEV Stage III), Central PM:0.004g/kWh to 2 Particulate Pollution Control Board, g/kWh Matter GSR 771(E), GSR232 (E), ISO 8178‐1:2006, ISO 8178‐4:1996

CHEMICAL TESTING

LOCATION 2

I. ATMOSPHERIC POLLUTION

1. Vehicle Emission Test From Temperature -10°C to 30°C. A) Tail pipe emissions

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed CO MoRTH/CMVR/TAP/115- 10 mg/km to 35 g/km HC 116(Issue 4, 0.6 mg/km to 5 g/km NOX Amendment 5,7,8) 1 mg/km to 2 g/km

CH4 0.6 mg/km to 1 g/km GSR400(E), GSR84(E), CO2 1 g/km to 500 g/km Fuel Consumption GSR103(E), GSR498(E), 2 km/l to 30 km/l (calculated from CO, GSR99 (E), GSR412(E), HC, CO ) GSR682(E), SO 2 1072(E), GSR954(E), Particulate Matter 0.000001 mg/km to GSR889(E) 0.5 g/km 6 15 Particulate Number R 83-07 Rev5: Supplement 1x10 to 9x10 number/km B) Idling Emission 6 to the Measurement 07 series of amendments, CO R-101 (Rev3Amendment6) Upto 9.99 % HC Upto 20000 ppm(V)(C6) C) Free Acceleration ADR79/05 0.001 m-1 to 10 m-1 Smoke EEC70/220lastamendedby 2006/96/EC, (EC)715/2007

D) Crankcase (EU) 2016/646, Qualitative emissions (EU)2017/1151, E) Evaporative (EU) 2017/1154, 0.01 g/test to 13 g/test emissions (HC) (EU)2017/1347 (Volume of SHED facility is 46.89 to 54.45 m³)

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed

ELECTRONICS TESTING

LOCATION 1

I. EMC TEST FACILITIES

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 1. Motor Vehicles Radiated Emissions CISPR 12:2009 30 MHz to 1000 MHz (2/3 Wheelers) (In ALSE chamber) AIS004(Part 1)/1999 Upto 90 dBµV AIS004(Part 3)/2009 (Annex 2 & 3) ECE R-10 Rev.05 (Annex 4 & 5) 97/24/EC Chapter 8 (Annex 2 & 3) SANS 20010:2010 (Annex 4 & 5) Radiated Immunity ISO 11451-2:2015 20 MHz to 2000 MHz (In ALSE chamber) AIS004 (Part 3)/2009 30V/m (Annex 4) ECE R-10 Rev.05 (Annex 6) 97/24/EC Chapter 8 (Annex 4) SANS 20010:2010 (Annex 6)

2. Vehicle Electronic Radiated Emissions AIS:004(Part 1)/1999 30 MHz to 200 MHz Systems/ (In ALSE chamber) AIS004 (Part 3)/2009 Upto 90 dBµV Sub-systems (Annex 5 & 6) ECE R-10 Rev.05 200 MHz to 1000 MHz (Annex 7 & 8) Upto 90 dBµV 97/24/EC Chapter 8

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed (Annex 5 & 6) SANS 20010:2010 (Annex 7 & 8) 150 kHz to 30 MHz CISPR 25 edition 4.0:2016 Upto 90 dBµV 3. ISM Equipment Radiated Emissions CISPR 11:2016 30 MHz to 1000 MHz (In ALSE chamber) CISPR 32:2015 Upto 90 dBµV 4. Vehicle Electronic Radiated Immunity AIS004:Part 3/2009 200 MHz to 2000 MHz, Systems/ (In ALSE chamber/ (Annex 7) 30 V/m Sub-systems BCI/Strip-Line) ECE R-10 Rev.05 (ALSE Method) (Annex 9) 97/24/EC Chapter 8 (Annex 7) SANS 20010:2010 (Annex 9) ISO 11452-2 second edition 200 MHz to 3100 MHz, 2004 (ALSE) 100 V/m SAE J1113-21:2005 (with ground Ref. plane method only) ISO 11452-4 fourth edition 1 MHz to 400 MHz, 2011 (BCI) 200 mA ISO 11452-5 second edition 100 kHz to 400 MHz, 2002 (Strip line) 200 V/m

5. Vehicle Electronic Conducted Emissions CISPR 25 edition 4.0:2016 150 kHz to 108 MHz Systems/ Upto 110dBµV Sub-systems operating on vehicle battery supply

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 6. ISM Equipment Conducted Emissions CISPR 11:2016 150kHz to 30MHz CISPR 32:2015 Upto 90dBµV 7. Vehicle Electronic Immunity to conducted ISO 7637-2:2011(E) Upto 12 V/24V DC, Systems/ transient disturbances AIS004:Part 3/2009 50 A Sub-systems on power supply lines (Annex 8) operating on Test pulse 1 (12/24 V ECE R-10 Rev.05 vehicle battery system) Test pulse 2a (Annex 10) supply (12/24 V system) Test SANS 20010:2010 pulse 2b (12/24 V (Annex 10) system) Test pulse 3a & 3b (12/24 V system) Test pulse 4 (12/24 V system) Load ISO 16750-2:2012 dump test pulse (For Load dump) (12/24 V system) Immunity to coupled ISO 7637-3:2016 Upto 12 V/24VDC, transient disturbances 50 A on lines other than power supply lines

Positive and negative test pulse (fast/slow) (12 V and 24 V system)

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Conducted transient ISO 7637-2:2011(E) Upto 12/24 V DC, emissions on power AIS004:Part 3/2009 50 A supply lines (Annex 8) ECE R-10 Rev.05 (Annex 10) SANS 20010:2010 (Annex 10) Electrostatic Discharge ISO 10605:2008 Upto 25 kV (Air and Contact IEC 61000-4-2:2008 Discharge) SAE J1113-13:2011 Immunity to ISO 11452-9:2012 28 MHz to 1950 MHz narrowband radiated Net power up to 50W electromagnetic energy. Portable/Handy transmitters Superimposed ISO 16750-2:2012 Upto 12/24V DC, alternating voltage. 16 A Slow decrease and increase of supply voltage. Discontinuities in supply voltage Withstand voltage Insulation resistance ISO 16750-2:2012 100 VDC to 500 VDC Test Voltage 1 MΩ to 10 MΩ Immunity to magnetic ISO 11452-8:2015 Frequency DC-150kHz fields Amplitude 1000A/m (Uniformed field area:30cm x 30cm x 30cm)

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 8. ISM equipment Radiated Immunity IEC 61000-4-3 80MHz to 2000 MHz Edition 3.2:2010 Upto 10V/m Field Uniformity IS 14700 (Part 4/Sec 3): 2008 Area 0.6m x 0.6m Burst on power/ IEC 61000-4-4:2012 Upto 4kV signal lines IS 14700 (Part 4/Sec 4): 2008 Surge on power supply IEC 61000-4-5:2014 Upto 4kV (1.2/50 µs) Conducted RF immunity IEC 61000-4-6:2013 Upto 10Vrms on Power lines Power frequency IEC 61000-4-8:2009, Upto 30A/m magnetic field IS 14700 (Part 4/Sec8): 2008 Power fail simulation IEC 61000-4-11 Edition 0%, 40%, 70%, 100% 2.0:2017

II. ENVIRONMENTAL TEST FACILITY

1. Vehicle Electronic Thermal Shock IEC 60068-2-14 Na:2009 0.5m x 0.6m x 0.45m Systems/ Test/Rapid change of IS 9000(Part 14/Sec 1): (-) 40 °C to 150 °C Sub-systems and temperature with 1988 SAE J1455:2017 Transfer Time < 10 sec. other Components prescribed time of JASO D 001:1994 transfer. Rapid ISO 16750-4:2010(E) Temperature Cycling JSS 55555:2012 Cold Test IEC 60068-2-1:2007 0.95 mx 0.95 mx 1.0 m Low Temperature IS 9000(Part 2):1977 Ambient to-50 °C JSS 55555:2012 Dry Heat Test IEC 60068-2-2:2007 0.95m X 0.95m X 1m High Temperature Test IS 9000(Part 3):1977 Ambient to 150 °C JSS 55555:2012

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Composite IEC 60068-2-38:2009 0.95m X 0.95m X 1m temperature/humidity IS 9000(Part 6):1978 50 °C to 150 °C. cyclic test Tropical JSS 55555:2012 30 % to 98 % RH for Exposure Temperature Range Damp Heat, cyclic IEC 60068-2-30:2005 (25 °C to 55 °C) (12 h + 12h cycle) IS 9000(Part 5/Sec 2):1981 Max. Ramp Rate:5 °C/min. Damp Heat, IEC 60068-2-78:2012 Steady State IS 9000(Part 4):2008 JSS 55555:2012 Temperature Cycling ISO 16750-4:2010(E) 0.95m X 0.95m X 1m Thermal Cycling SAE J1455:2017 50 °C to 150 °C. Change of temperature IEC 60068-2-14 Nb:2009 Max. with specified change of IS 9000(Part 14/Sec 2): Ramp Rate:5 °C/min temperature 1988 Vibration Testing JIS D 1601:1995 Sine and Random IEC 60068-2-64:2008 Frequency: SAE J1455:2017 5 Hz to 2000 Hz SAE J1211:2012 Velocity:1800 mm/sec. IS 9000 (Part VIII):2003 X, Y Axis 30 G IEC 60068-2-6:2007 (Bare Table). ISO 16750-3:2012 Z Axis 82 G (Bare Table). JASO D 001-94 Mechanical Shock JASO D 001-94 100 g, 6 ms and 50 g, IEC 61373:2013 11ms with a mass of 1 kg IEC-60068-2-27:2008 JSS55555:2012

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Combined Temperature ISO 16750-3:2012 Frequency:5 Hz to 2000 Hz; and Vibration Test IEC 60068-2-64:2008 Velocity:1800 mm/sec. Z Axis-40 g Temperature: (-) 50°C to 150°C Max. ramp rate 5 °C/min Humidity:30 to 95% r.h. Chamber Size:0.95 x 0.95m x 1m

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed

MECHANICAL TESTING

LOCATION 1

I. MECHANICAL PROPERTY OF METELS

1. 5th wheel coupling Static test-1 AIS 091/Part 1,2009 and mounting Limit of deformation & ECE R 55,2018 plate width under specified Annexure 6 Clause 25 KN to 250 KN load No.3.7.2.2 Static test-2 Separation of coupling pin under specified load Dynamic test AIS 091/Part 1,2009 & Number of cycles for ECE R 55,2018 test pass or fail Annexure 6 clause Horizontal force No.2.2 and 3.7.3.1 20 kN to 220 kN Vertical force 50kN to 500 kN 2. 5th Wheel King Pin Dynamic test AIS 091/Part 1,2009 & Number of cycles for ECE R 55,2018 test pass or fail Annexure 5 clause 8 Load Annexure 6 clause 25 KN to 250 KN No.2.2 and 3.9 3. Metals and Axial Fatigue Number ASTME 466-15 Alloys of cycles for test pass or fail Load 25 kN to 250 kN Fatigue life estimation 5 kN to 25 kN (S-N Curve)

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 4. Ferrous & Non- Residual Stress SAE HS 784:2003 2θ angle Ferrous Measurement Scanning range:10° to 163° (Normal stress) II. PERFORMANCE/DURABILITY/SAFETY TEST

1. Vehicle Horn Installation IS 15796-2008 Installation Testing ECE R28; amendment 3 testing: Horn Sound Level supplement 3 Rev2 80 dBA to 125 dBA Installation Voltmeter 12 V to 30 V 2. Vehicle Wind Screen wiping AIS 045-2004 Installation system test IS 15802:2008 testing: Angle of the tangent IS 15804:2008 5° to 180° Windscreen from the eye ellipse Wiping Temperature (-) 20 °C to 55 °C Linear dimension 10 mm to 3000 mm 3. Vehicle Installation High speed test AIS 002:2001 (Cl. No. 4.2) Upto 80 %of max speed of testing: Rear View Field of vision test AIS 002 (Part 1) (Rev. 1): the vehicle or 160 kmph mirror installation 2011 AIS 002 (Part 2) whichever is less test (Rev. 1):2011 Test for Rearview mirror ECE R46 Rev 4, 03 series 10° to 90° position of amendments SANS:20046-2006 4. Automotive Dimensional check IS 15636-2005 component Section width of tyre AIS 110 ECE R No. 54 150 mm to 450 mm testing: Tyre outer diameter amendment No.2 Rev No.2 500 mm to 1600 mm Pneumatic tyres SANS:20054-2007 for commercial vehicles diagonal and radial ply

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Load/Speed IS 15636-2005 20 °C to 40 °C Performance Test AIS 110-2009 32 km/h to 96 km/h ECE R No. 54 1. 200 kg to 10000 kg Amendment No.2 Rev No.2 2. 200 kg to 5000 kg SANS:20054-2007 100 kPa to 1000 kPa Endurance Test IS 15636-2005 20 °C to 40 °C ECE R No. 54 80 km/h to 90 km/h SANS:20054-2007 1. 200 kg to 10000 kg 2. 200 kg to 5000 kg 100 kPa to 1000 kPa Tyre Strength Test IS 15636-2005 10 kPa to 180 kPa AIS 110-2009 50 (±) 1.5 mm/minute 100 kg to 10000 kg Tread-Wear-Indicators IS 15636-2005 1 mm to 5 mm AIS 110-2009 ECE R No. 54 Amendment No.2 Rev No.2 SANS:20054-2007 Markings IS 15636-2005 5 mm to 50 mm AIS 110-2009 ECE R No. 54 Amendment No.2 Rev No.2 SANS:20054-2007 5. Driver’s forward Driver’s forward Field of AIS 021-2011 1° to 6° Field of Vision Vision Amendment 1 EEC 77/649

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed

6. Pneumatic tyres Dimension test IS 15627:2005 for two wheeled- Section width of tyre 50 mm to 300 mm vehicles-under Diameter of tyre IS 15627:2005 150 mm to 700 mm speed capability Tread wear indicators IS 15627:2005 0.8 mm (+0.60/-0.0) mm of 150km/h Endurance test IS 15627:2005 20 °C to 40 °C 20 km/h to 200 km/h 20 kg to 2000 kg 10 kPa to 300 kPa Load Speed IS 15627:2005 20 °C to 40 °C Performance test 50 km/h to 350 km/h 50 kg to 2000 kg 10 kPa to 300 kPa Plunger test IS 15627:2005 150 kPa to 300 kPa 50 (±) 1.5 mm/minute 100 kg to 2000 kg Markings IS 15627:2005 5 mm to 50 mm 7. Signaling Devices Vehicle Installation for Motor Vehicle testing:Installation having more than Requirements of Lighting and Light

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Three Wheels, Presence AIS 008 (Rev. 1):2010 1 m to 30 m (±) 1mm Trailer and Semi- Number ECE R48.03, Rev4, 0.5 m to 5 m (±) 1 mm Trailer excluding Arrangement amendment 01 Agricultural Position 2° to 180° (±) 2° Tractor and Geometric Visibility Special Purpose Orientation Vehicle Electrical connection Tell-tale 5 s to150 s Other requirements

8. Signaling Devices Vehicle Installation for L Category testing:Installation Vehicles, their Requirements of Trailers and Lighting and Light Semi-Trailers Number AIS 009-2001 Upto 30 m (±) 1mm Arrangement ECE R53 Upto 5 m (±) 1 mm Position ECE R74 Geometric Visibility Orientation Upto 180° (±) 2° Electrical connection Tell-tale Upto 150 s (±) 1 s Other requirements 9. Safety Belt Dynamic test using Cl.4.4.2,5.5.2of ‘g’ Level 29±3g within Assembly Bungee Sled Facility IS-15140:2003 specific Corridor, after all the specified Cl.6 of ECE16-07-07 series Speed 50±1 kmph, Pre-conditioning such of amendments Manikin fwd displacement as Retractor durability, Cl.6 of ADR4/05 between 40 mm to 200 Buckle Durability, Dust Cl.6 of SANS20016:2009 mm at Pelvic level 50 mm Test, Salt Spray test to 500 mm at Torso level 10. Safety Belt Tensile strength after Cl.No4.2,4.3,5.2,5.4of Upto100 KN

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Assembly: various conditioning IS 15140:2003 Webbing or such as Cl.No.6.2,6.3,7.4,7.5 of Straps/Rigid Parts Room/Cold/Heat/Light/ ECE16-07-Cl.6 of Water Abrasion ECE16-07-07 series of amendments Cl.6 of ADR4/05 Cl.No.6.2,6.3,7.4,7.5 of SANS20016:2009

Elongation Cl.No.4.3.5,5.4.3of Upto 40 mm IS 15140:2003 Energy Absorptivity Cl.No.4.3.6,5.4.4of Work Load Ratio>50, IS 15140:2003 Work/Length Nm/m>500 Width under Load Cl.No 4.3.1.2,5.4.1 of Upto 50 mm IS 15140:2003 Cl.No.6.3.1.2,7.4.3 of ECE16-07-Cl.6 of ECE16- 07-Cl.6 of ECE16-07- 07series of amendments Cl.6 of ADR4/05 Cl.No.6.3.1.2,7.4.3 of SANS 20016:2009 11. Safety Belt Micro Slip test Cl.No.4.2.3.1 and 5.2.8 of 1000 cycles, Assembly-2 IS 15140:2003 Strap Slipup to 50 mm Point Static/ Cl.No.:7.3 of ECE 16-07- 3 Point Static Cl.6 of ECE16-07-07series of amendments Cl.6 of ADR 4/05

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Cl.No.7.3 of SANS 20016:2009 12. Safety Belt Buckle Release Force Cl.No.4.4.2.10.c) and 5.5.3 Upto 500N Measurement Test of IS 15140:2003 Cl.No.6.2.2.5 and 7.8 of ECER 16- 07-Cl.6 of ECE 16-07-07 series of amendments Cl. 6 of ADR 4/05 Cl.No.6.2.2.5 and 7.8 of SANS 20016:2009

G Lock Test Cl.No.4.2.5.3 and 5.3.2 of Upto 200 mm IS 15140:2003 0.45 g to 5 g Cl. No. 7.6.1,7.6.2, 6.2.5.3.1.1, 6.2.5.3.1.2 of ECER 16-07-Cl.6 of ECE16-07- 07 series of amendments Cl.6 of ADR 4/05 Cl. No. 7.6.1,7.6.2, 6.2.5.3.1.1,6.2.5.3.1.2 of SANS 20016:2009

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Manual Belt Adjuster Cl.No.4.2.3.3 and 5.2.6 of Upto 500 mm Force Measurement IS 15140:2003 Upto 500 N Test Cl.No.6.2.3.4 and 7.5.6 of ECER16-07-Cl.6 of ECE16- 07-07 series of amendments Cl.6 of ADR4/05 Cl.No.6.2.3.4 and 7.5.6 of SANS 20016:2009 Retractor Retraction Cl.No.4.2.5.2,4.2.5.3 and Upto 2000 mm Force Measurement 5.3.4 of IS 15140:2003 Upto 110 N Test Cl.No.7.6.4 of ECER16- 07Cl.6 of ECE16-07-07 series of amendments Cl.6 of ADR4/05 Cl.No.7.6.4 of SANS 20016:2009

Retractor Tilt Lock 4.2.5.3.a.3,4.2.5.3. a.4 and Upto 40° Test 5.3.2.5 of IS 15140:2003 Cl.No.6.2.5.3.1.3 and 6.2.5.3.1.4 of ECER 16-07-Cl.6 of ECE 16-07- 07 series of amendments Cl.6 of ADR 4/05 Cl.No.6.2.5.3.1.3 and 6.2.5.3.1.4 of

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed SANS 20016:2009 Cl.No.7.2.3.2 of AIS 072:2011 13. Seats Dynamic test Cl.5.1,5.3 of ‘g’ Level 0 to 50g, (Seats and their (Resistance to Inertia IS 15546:2005 Pulse Width 0 to100 ms Anchorages) Effects) Cl.6.3 of ECE17-08- Using Bungee Sled Supplement 4 to the 08 Facility series of amendments Clause 4.2.3,4.3.3 of AIS-023 Cl.6.3 of Appendix A of ADR 3/03 Cl.6.3 of SANS 20017:2004 14. Seats Luggage Retention test Cl.5.15 of ECE17:08- ‘g’ Level 24±4 g Using Bungee Sled Supplement 4 to the 08 Within Specific Corridor, Facility series of amendments Speed 48 to 50 kmph, Cl.No.5.9 of IS 15546:2005 Seat Back and Head Cl.5.15 of Appendix A of Restraint Movement wrt ADR3/04 R Point Upto 200 mm Cl.5.15 SANS 20017:2004

15. Cabins& their Frontal Impact Test (Test Cl.5.2 of AIS 029/2004 3000 mkgf for vehicles attachments of A) using Pendulum weighing<=7.0tons Commercial Impact Test Rig 4500mkgf for vehicles Vehicles of weighing>7.0tons Category N Cl.5.2 of ECER 29.02 29.4kJforvehicles Supplement 1 to the series weighing<=7.0tons 02 of amendments 44.1kJforvehicles weighing>7.0tons

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Cl.5.1.2 of ECER 29.03 29.4kJforvehicles 03 series of amendments weighing<=7.0tons 55kJforvehicles weighing>7.0tons 16. Driver/Passenger/ Static Airbag SAEJ1630-JAN2011 Temperature Conditioning Seat Airbag Deployment Test after from-35°C to +90°C, Modules temperature Programmable Firing conditioning Current Pulse up to 5A (Exclusion:Sun Load Simulation and Pressure Measurement) 17. Strength of Full Vehicle Rollover Cl.7.1.1,Cl.8 of Rate of Tilting≤5deg./sec Superstructure of AIS 031/2004 Intrusion of vehicle Large Passenger incl. Amd.1, superstructure into Vehicles Cl.5.1toCl.5.3 of residual space ECER66.01

18. Child Restraint Systems(CRS) 19. Complete CRS Resistance to Cl.No.7.1.1of AIS 072:2011 50±0.5hrs;Annex-4; Corrosion Amd.#1,2 Cl.7.1.1 of ECE Visual Inspection R44.04 Energy Absorption Cl.No.7.1.2 of AIS 072:2011 Head form drop, Cl.7.1.2 of ECE R44.04 2.75kg (±) 0.05kgfrom 100-0 (+) 5mm; Peakg≤60

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Overturning Test Cl. No.7.1.3 of AIS 072:2011 Manikin head Movement Cl.7.1.3 of ECE R44.04 Upto 300 mm 20. Complete Child Resistance to Cl.7.1.5 of AIS 072:2011 (-) 30to (+) 180 °C Restraint System Temperature Cl.7.1.5 of ECE R44.04 Visual Inspection /Buckle Area Cl.No.7.2.1.2 of Upto100 mm assemblies, AIS072:2011 retractors, Cl.No.7.2.1.2of ECE Adjusters and R44.04 lock-off devices 21. CRS Child Parts: Durability Cl.No.7.2.1.7 of 5000 cycles; Buckle AIS 072:2011 Operational check Cl. No.7.2.1.7 of ECE R44.04 Opening Force under Cl. No. 7.2.1.8 of Upto 500N no-load AIS 072:2011 Opening Force under Cl. No. 7.2.1.8 of ECE Upto 500N load R44.04 Strength Cl.No.7.2.1.9 of Upto 100KN AIS 072:2011 Cl. No. 7.2.1.9 of ECE R44.04

Operating Force Cl. No. 7.2.2.4 of AIS Upto 50N 072:2011 l.No.7.2.2.4 of ECE R44.04 22. CRS Child Parts: Resistance to Cl.7.1.5 of AIS 072:2011 (-) 30 to (+) 180°C Visual Adjusting Devices Temperature Cl.7.1.5 of ECE R44.04 Inspection Micro slip test for- Cl.No.7.2.2.5 of AIS 1000 cycles, Adjuster not directly 072:2011 Strap Slip mounted on CRS Cl.7.2.2.5 of ECE R44-04 Upto 50mm

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Micro slip test for- Cl.No.7.2.2.6 of AIS 5000 Cycles; Adjuster directly 072:2011 strapslip≤25mm mounted on CRS Cl.7.2.2.7 of ECE R44-04 23. CRS Child Parts: Retractor Durability Cl.No.7.2.3.2.6 of AIS 40000 Cycles; Operational Automatic 072:2011 Cl.No.7.2.3.2 of Check Locking ECE R44-04 Retractors/ Tilt Lock Cl.No.7.2.3.2 of AIS Upto 40° Emergency G lock Test 072:2011 Up to 200 mm Locking Retractors Cl.No.7.2.3.2 of ECE R44-04 0.45 g to 5 g Retraction Force Cl.No.7.2.3.2.1 and Upto 2000 mm Measurement Test 7.2.3.2.5 of AIS0 72:2011 Cl.No.7.2.3.2.1 and Upto 110 N 7.2.3.2.5 of ECE R44-04 Dust Test Cl.no.8.2.4.5 of AIS 072 Visual Inspection Cl.no.8.2.4.5 of ECER44-04 Operational check 24. CRS Child Parts Width Cl.7.2.4.1 of AIS 072:2011 Upto 100 mm Straps Cl.7.2.4.1 of ECE R44-04 Strength after room Cl.7.2.4.2 of AIS 072:2011 Upto100 KN conditioning Cl. 7.2.4.2 of ECE R44-04 Strength after special Cl.7.2.4.3 of AIS 072:2011 conditioning Cl.7.2.4.3 of ECE R44-04

25. CRS Child Parts Micro slip:Class B Cl.7.2.5.3 of AIS 072:2011 60cycles; Lock-Off devices devices Cl.7.2.5.3 of ECE R44-04 strapslip≤25mm 26. Complete Child Dynamic Test Cl.7.1.4 of AIS 072:2011 Forward Impact: Restraint System 50-2+0kmph;‘g’levelwithin Cl.7.1.4 of ECE R44.04 specific corridor; Manikin Chest Acceleration:resultant ≤55g; Peak Upwards≤30g;

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Head forward &upward movement within limits Rearward impact: 30-2+0kmph; ‘g’levelwithin specific corridor; Manikin Chest Acceleration: ≤55g; Peak Upwards≤55g; Head forward &upward Movement within limits 27. BIW+Seat Seat Belt IS 15139/2002 Cl No. 4.5; Upto 20.25 kN for 3 point Anchorage Test ECER 14 Rev.07/2012cl. belts 6.1 to 6.4 excluding ISO FIX anchorages; ADR 05/5 year 2006 Upto 33.37 kN for 2 point Amendment1-Cl.6.4 only belts SANS 20014:2004 28. Automotive Dimensional IS 15546/2005 Cl. 4.4,4.5, Seats measurements of head 4.6.1 ECE regulationno restraint R 17, Revision 08/2009 Height CL. 5.5,5.7,5.10 Upto 1100 mm Width ADR 03/3 year 2006 Upto300 mm Gap Amendment1-Cl. 6.6 & 6.7 Upto 80 mm SANS 20017:2004 Width AIS 023/2205 Cl 4.2.1, Upto 500 mm Depth 4.2.2,4.3.1,4.4.1, Upto 500 mm Back Rest Height 4.4.2, 4.5.1 (Component Upto 1, 200 mm Torso Angle Level dimensions) Upto 25 Degree Longitudinal adjustment Upto 100 mm Arm Rest Height Upto 300 mm Arm Rest Width Upto70 mm

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Head restraint IS 15546/2005 Cl. 4.7, performance test reference standards ECE Moment regulation no R17, Revision Upto 560 Nm Force 08/2009 Cl 5.12 Upto1335N R point Deflection of ADR 03/3 year 2006 less than 102 mm HR Amendment 1-Cl.6.4 SANS 20017:2004 AIS023/2005 Cl No 4.2.3 Seat Back IS 15546/2005 Cl. 4.3.1 Strength test reference standard ECE Moment about Rpoint regulation no R17, Upto 795 Nm Revision 08/2009 Cl 6.2 ADR 03/3 year 2006 Amendment 1-Cl.6.2 SANS 20017:2004 AIS023/2005 Cl No 4.2.3 Energy Dissipation test IS 15546/2005 Cl. 4.2.2, Deceleration of Head 4.2.3 ECE regulation No. Upto 250g continuously for Form R17,08/2009CL5.5.2 more than 3 milliseconds. ADR 03/3 year 2006 Amendment 1-Cl.6.8 SANS 20017:2004 AIS 023/2005 Cl. No.4.2.3

Seat Static Strength i) AIS 023/2005 Cl. 5.0 test Load Upto 35 kN Displacement 50 mm to 400 mm Seat Anchorage test i)AIS 023/2005 Cl. 7.0 Load Upto 40kN

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 29. Automotive vehicle Verification of weights IS 11825:1986 Upto 60000 kg testing 2W, 3W, 4W, of vehicles Agricultural Tractor, Automotive Trailer, Construction Equipment Vehicles (CEV)& their derivatives 30. Automotive Constant Speed Fuel vehicle testing Consumption 2W, 3W, 4W & Evaluation their derivatives 2 Wheelers and their IS 10881:1994 0.4 L/hr to 60 L/hr. derivatives 3 & 4 Wheelers and IS 11921:1993 0.06 L/hr to 60 L/hr. their derivate

31. Automotive Brake Performance vehicle testing Evaluation 2W, 3W, 4W & Speed 71/320/EEC or ECE R13 Upto 140 km/h their derivatives, i) 4 Wheelers and their IS 11852:2001 ADR 31/01, (Speed limit on N-CAT Test Automotive derivatives, Automotive 31/02,31/03, 35/00, 35/01, Track is=150 km/h) Trailer, Trailer 35/02, 35/03, 35/04

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Construction ii) 2 & 3 Wheelers and 93/14/ EEC IS 14664:1999 Equipment their derivate ADR 33/00 Vehicles (CEV), iii) Construction Central Vehicle Motor Rule Agricultural Equipment Vehicles No-96 Tractor and Trailer (CEV) combination iv) Braking System and AIS043 Amd.03-2005 Performance Requirements for the Combination of Agricultural Tractor and Trailer combination 32. Automotive vehicle Gradeability Evaluation AIS003-1999 7°,10.2°,15°,25°& 30° testing 2W, 3W, 4W IS 13988-2002 & their derivatives 33. Steering Torque 70/311/EEC or ECE R79 250 Nm Equipment for Angle IS 11948-1999 1250° Automotive Steering Equipment for AIS 042:2017 vehicle testing for 4 wheeler & Agricultural AIS 113 4W, Agricultural tractors, Automotive tractors, trailer Automotive trailer & Construction Equipment Vehicles (CEV) 34. Automotive Turning Circle Diameter IS 12222:2011 70m vehicle evaluation IS 11859:2004 4W, Agricultural tractors & Construction Equipment

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Vehicles (CEV) 35. Automotive Speedo meter vehicle Calibration 2W, 3W, 4W, Speed 97/39/EEC or ECE R39, Upto 140 km/h Construction i) 4 Wheelers and their IS 11827-1995, 2008 (Speed limit on N-CAT Equipment derivatives & Test Track is 150 km/h) Vehicles (CEV) & Construction their derivatives Equipment Vehicles (CEV) ii) 2 & 3 Wheelers and 2000/7/EEC their derivate IS 11827-1995, 2008 36. Automotive Coast Down Test IS 14785-2000 Vehicles 4W Speed TAP-115/116 Upto 140 km/h (Speed limit on N-CAT Test Track is 150 km/h) 37. Automotive Max. Speed Test Vehicles Speed ECE/68, IS 11877:1986 Upto 150 km/h 2W, 3W, 4W, i) 4 Wheelers and their (Speed limit on N-CAT Construction derivatives Test Track is 150 km/h) Equipment ii) 2 Wheelers and their 95/1/EEC, IS 10278:2002 Vehicles(CEV) & derivatives Agricultural iii) 3 Wheelers and their 95/1/EEC Tractor their derivate derivatives iv) Agricultural Tractor AIS 116 38. Automotive Permissible Sound 30 dB(A) to 130 dB(A) Vehicles Level Test 2W, 3W, 4W, i) 4 Wheelers and their IS 3028-1998 70/157/ Agricultural derivatives EEC, ECE R51, ADR 83/00

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Tractor & their ii) 2 Wheelers and their IS 3028-1998, derivatives derivate ECE R41, ADR 83/00 iii) 3 Wheelers and their IS 3028-1998, derivate ADR 83/00 iv) Agricultural Tractor AIS 115 (Part 2) By stander Noise and AIS 115 (Part 1) OEL Noise level 39. Automotive Internal Sound Level AIS 020, IS 12832:1989 30 dB(A) to 130 dB(A) Vehicles Hood Latch Tests IS 14226:1995 120 km/h 4W & their derivatives 40. Automotive External projection- IS 13942:1994 10 mm to 10000 mm Vehicles Performance 2W, 3W, 4W& their Requirements derivatives except for two and three wheeled vehicles below 500 cc. 41. Automotive The Arrangement of AIS 035 30 mm to 500 mm Vehicles of Foot Controls of category M1 and Vehicles L7-M

42. Automotive Identification of AIS 126 Amd.01-2017 Visual Vehicles of Controls, Tell-Tales, category Indicators, Control “L1 & L2” Location & Operations Requirements

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 43. Automotive Identification of AIS 071 (Part1& Part2) Visual Vehicles of Controls Amd.01-2015 category L, M, N, Tell-Tales and A and C Indicators 44. Automotive Wheel Guards IS 13943:1994 10 mm to 2000 mm Vehicles- For Passenger Cars- Amd.01-2016 passenger cars Performance Requirements 45. Automotive Temporary-Use Spare AIS-110:2009 Vehicles of Wheel/Tyres and Run Amd.01-2013 vehicle category Flat Tyres M1 & N1 Speed Upto 80 km/h 46. Automotive Physical/Dimensional AIS-052 (Rev.1):2008 10 mm to 20000 mm vehicles-Fully and Other verification of Amd.08 Built Bus, Buses (Bus Code) FullyBuilt School Physical/Dimensional AIS-063:2005 Amd.09 10 mm to 20000 mm Bus & Sleeper and Other verification of Coaches School Buses Specific Constructional AIS-119 (Rev 1):2016 10 mm to 20000 mm Requirements for Sleeper Coaches

47. Automotive Measurement of IS 9435-2004 30 mm to 500 mm vehicles-Other Ground than 2W & 3W Clearance 48. Automotive Physical/Dimensional AIS 056 Rev. 01 10 mm to 20000 mm vehicles-Category and Other verification of

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed N2 &N3 Vehicles Truck Cabin Ventilation System for Category N2 & N3 Vehicles Physical/Dimensional AIS-093 (Rev.1) and Amd. 10 mm to 20000 mm and Other verification 1 and 2 for Construction and Approval of Truck Cabs & Truck Bodies 49. Automotive Constructional and AIS-125 (Part 1) and Amd 1 10 mm to 20000 mm vehicles-Category Functional & 2 M & L Vehicles Requirements for Road Ambulances 50. Pneumatic tyres Dimensional check IS 15633-2005 for passenger car Section width of tyre AIS 110 100 mm to 400 mm vehicles diagonal Tyre outer diameter ECE R 30 amendment No.2 200 mm to 1000 mm and radial ply Rev No.3 ADR 23 SANS:20030-2007 Load/Speed IS 15633-2005 20°C to 40 °C/ Performance Test AIS 110 30 °C ECE R 30 amendment No.2 100 km/h to 350 km/h Rev No.3 200 kg to 2500 kg ADR 23 100 kPa to 500 kPa SANS:20030-2007

Endurance Test IS 15633-2005 20 °C to 40 °C 80 km/h to 90 km/h 200 kg to 10000 kg 100 kPa to 1000 kPa IS 15633-2005 50 (±) 1.5 mm/minute

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Bead Unseating AIS 110 100 kg to 3000 kg Resistance Test for 10 kPa to 180 kPa Tubeless Tyre Tyre Strength Test IS 15633-2005 AIS 110 50 (±) 1.5 mm/minute 100 kg to 10000 kg 100 kPa to 500kPa Tread-Wear-Indicators IS 15633-2005 1.0 mm to 5 mm AIS 110 ECE R 30 amendment No.2 Rev No.3 ADR 23 SANS:20030-2007 Markings IS 15633-2005 5 mm to 50 mm AIS 110 ECE R 30 amendment No.2 Rev No.3 ADR 23 SANS:20030-2007 III. RUBBER AND RUBBER PRODUCT

1. Rubber Durometer Hardness ASTM D2240-2015 20 Shore A & D to Rubber:Shore A 90 Shore A & D Plastic:Shore D Hardness (IRHD) ASTM D1415-2006 (2012) 30 IRHD M &N to Micro & Normal 95 IRHD M &N

IV. PLASTICS & PLASTIC PRODUCTS

1. Plastic Durometer Hardness ASTM D2240-2015 20 Shore A & D to Rubber:Shore A 90 Shore A & D

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Plastic:Shore D Hardness (IRHD) ASTM D1415-2006 (2012) 30 IRHD M &N to Micro & Normal 95 IRHD M &N V. NOISE AND VIBRATION

1. Automotive porous Flow resistivity ISO 9053-1991 and 1000 to 1000000 (N.s/m4) materials such as ASTM C-522-2003 foams, fibers, boards scrims, blankets 2. Automotive porous Normal incidence ISO 10534-2-1998, ASTM 100 Hz to 6300 Hz material such as sound absorption E-1050-2012 (0.05 to 1) foam, fibers, dash coefficient panel, carpet, seats, measurement using headliners, jute impedance tube 3. Automotive sound Random incidence ISO 354-2003 and 125 Hz to 5000 Hz package materials sound absorption ASTM C-423-17 (0.05 to 1) such as floor coefficient carpet, dash panel, measurement using headliner, hood Reverberation chamber insulator Non- Automotive building acoustic materials such as PU foam, Rockwool Glass wool, Curtains, ceiling tiles 4. Automotive sound Sound transmission ISO 10140-2-2010/ 125 Hz to 5000 Hz Package materials loss measurement ASTM E 90-09 (6 dB to 70 dB)

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed such as Floor using reverberation Carpet, Dash Panel, chambers Headliner, Glass Panel, Sheet Meal etc. Non- Automotive Building Acoustic Materials Such as Drywall Partitions, Glass Partitions, Roofing Systems, Doors, Windows 5. Horn Measurement of sound IS 1884:1993 80 dBA to 125 dBA level ECE R-28-Rev. 2 Sound spectrum (Amendment 3, 80 dBA to 125 dBA Supplement 3 to original (1.6 KHz to 4 KHz) Endurance version of the 1 sec ON/4 sec (3 sec) regulation) OFF Vibration test 10 to 55 Hz, SANS:20028-1972 0.75 mm 3 hrs Corrosion Resistance 25 °C to 55 °C Test 1 hrs to 1000 hrs. Damp Heat Test 25 °C to 55 °C (Cycling test) 80 % to 95 % RH 7 cycles (24 hrs. one cycle) Water Spray Proof Precipitation of 2.54 mm of Test water per minute at 45° spray angle, 4 rev/min, 6 hrs.

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Temp Stability Test 70°C/55°C for 4hrs/16hrs and-10°C for 2 hrs Insulation Resistance 50 °C to 60 °C, test 95 %RH 48 hrs, 500 V dc Current Draw Test At rated voltage current measurement Upto 15A Operating Voltage From 5 Vdc to 30 Vdc Range Test High Voltage test AC 240 V rms, frequency between 40 HZ to 60 HZ for 5 seconds Continuous operation 80 dBA to 125 dBA test Dust Test At interval of 15min., 2 sec. dust agitation, 5hrs test duration

VI. AUTOMOTIVE COMPONENTS

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 1. Safety Glass Dimensional check IS 2553 (Part II)-1992 1 mm to 25 mm (thickness) (Laminated and Toughened) ECE R-43-01 supplement 2 Fragmentation Test to the 01 series of 40 nos to 400 nos. (Toughened) amendments Mechanical (-) 15°C, 60°C & Strength/Impact SANS:20043-2005 Ball weight:227g, Resistance test Height of drop:1.5 to 12 m (Laminated & Toughened) Penetration Ball weight 2260g, (Laminated) Height of drop:1.5 to 12m Resistance to high 60 ° C to 100 °C temperature (Boil test) Temperature and 30 °C to 180 °C humidity (Laminated) 95%RH Head form Weight of Head Form (Laminated) 10 kg, Height of drop:4 m Resistance to 750 W (±) 50 W radiation (Laminated) 2. Door Hinges & Longitudinal load test IS 14225-1995 100 kgf to 30000 kgf latches for Hinges & latches ECE R-11-03 supplement 03 to the 03 & 04 series of Transverse load test for amendments Hinges & latches SANS:20011-1981

3. Rear View Mirror Radius of curvature AIS 001, Rev 01, Part1 and 100 mm to 2000 mm Part 2-2011

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Co-efficient of reflection ECE R 81-Amendment 1 2.5 % Supplement 2 to the 00 Upto 100 % Impact test series of amendments. 2 ° to 60 ° Bending test ECE R-46, Rev3, At 25 Kg Load Supplement 4 to the 02 series of amendments. ADR 14, 2006 Amendment 1 4. LPG Pressure Tests for Class 1, ECE R-67-04 Regulator, LPG Class 2 (A) and Class 3 solenoid valve, Over Pressure 1000 kPa to 10000 kPa Gas air mixer External Leakage 1000 kPa to 10000 kPa (-) 40 °C to 120 °C High temperature 1000 kPa to 10000 kPa (-) 40 °C to 120 °C Low temperature 1000 kPa to 10000 kPa (-) 40 °C to 120 °C Seat leakage 1000 kPa to 10000 kPa

LPG compatibility Weight loss <5% Volume change20%Max. Corrosion resistance 25 °C to 55 °C test temp. 1 hrs to 1000 hrs. 500 g to 10 kg Resistance to dry heat. 50 °C to 150 °C temp. Creep. 1000 kPa to 10000 kPa 30 °C to 120 °C Temperature cycle. (-) 40 °C to 120 °C

5. Electrical Fuse Electrical Fuse Test AIS 026:2002 5 Amp. to 13.5 Amp.

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Clause No.12 (c) 10 sec to 70 min. AIS 028:2015 Clause No.4.3.3 6. CNG Pressure Hydro-static strength. ISO 15500:Part 9-2016, 5 MPa to 100 MPa Regulator, CNG Leakage Part 6-2016, 5 MPa to 30 MPa Solenoid Valve, Excess Torque Part 11-2015 3 kg-m to 14 kg-m CNG Gas Air Resistance Part 2-2016 Mixer Electrical over voltages. IS 15712-2006; 9 Volts DC to 18 Volts DC, IS 15713-2006; for 3 minutes Vibration Resistance IS 15714-2006 Acceleration 1.5g, Frequency Range 10Hz to 500 Hz Sweep Time 10 minute Resonance frequency 500Hz Corrosion resistance Qualitative (Sodium Chloride concentration in distilled or deionized water 50 g/l., 35°C test temp. for 144 hrs or 500 hrs.) Brass Material Exposure to Ammonia air compatibility. mixer at 34°C for 10 days. Insulation resistance. 10 kΩ to 240 kΩmin. Minimum opening 8 to 16 V DC at 0.75 times voltage. WP Pressure impulse. 1 MPa to 20 MPa Water jacket freezing. (-) 10 °C or (-) 40 °C

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 7. CNG Rigid piping Burst Pressure Test AIS 028-2002 10 MPa to 100 M Pa and connections Clause No.3.1.1 IS 15716-2006 Corrosion Resistance ASTM B117-2007 25 °C to 55 °C test temp. Test 1 hrs to 1000 hrs. 500 g to 10 kg 8. LPG Rigid piping Pressure Test AIS 026:2002 10 kg/cm2 to 100 kg/cm2 and connections Clause No.9 (a)(i). 9. Wheel Rim Radial Fatigue test IS 9436-1980 500 kgf to 3000 kgf Corner Fatigue test IS 9438-1980 500 kg-m to 3000 kg-m 10. Hydraulic brake Visual examination IS 7079:2008 hose Constriction test Within 1 sec.to 10 sec. Whip test Pressure 0.5 Mpa to 2 Mpa Rotational speed 100 rpm to 900 rpm Whip life of min1-100HRS. Pressure test 10 MPa to 100 MPa Burst test 10 MPa to 100 MPa Tensile test 10 N to 4000 N Cold bend test (-) 20 °C to (-) 50 °C Expansion test Burette:0.5 cc to 10 cc 1 MPa to 30 MPa Salt spray test 25 °C to 55 °C test temp. 1 hrs to 1000 hrs. 500 g to 10 kg Ozone resistance test 10 pphm to 100 pphm

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Brake fluid compatibility 50 °C to 120 °C

Hot Impulse Strength 1 MPa to 11 MPa; Test 30 °C to 150 °C Water Absorption 30 °C to 85 °C Test 11. Anti-theft devices Torque test for key AIS 075-2005 0.5 Nm to 2.45Nm (Device to prevent ECE R 18:Rev 3, 03 series unauthorized use)- of amendments Locks the steering ECE R 116 Rev 2 Lock Bolt strength test AIS 075-2005 10 Nm to 300 Nm ECE R 18:Rev 3, 03 series of amendments ECE R 116 Rev 2 Wear Producing test AIS 075-2005 5 Nm to 50Nm ECE R 18:Rev 3, 03 series of amendments ECE R 116 Rev 2 12. Anti- Torque test for key AIS 074 0.5 Nm to 2.45 Nm theft devices (component level and ECE R 62; amendment 01 (Device to prevent vehicle level) corrigendum 1 unauthorized use) ECE R 116 Rev 2

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Lock Bolt strength test AIS 074 10 Nm to 200 Nm (component level and ECE R 62; amendment 01 vehicle level) corrigendum 1 ECE R 116 Rev 2

13. Metallic-Fuel Tank Leakage test IS 12056:1987 Cl. No 4.1, 10 g to 100 g/min when for 4 Wheelers AIS 104, Cl. No. 4.1.1 inverted for 5 minutes for Tractor 10 g to 100 g/min (PTO power up to 75kW) 10 g to 100 g/min (PTO power above75kW) Pressure test IS 12056:1987 Cl. No. 4.3 Qualitative ECE R 34-2001Cl.6.1 (No mechanical failure of AIS 104, Cl. No. 4.1.3 tank.) Vent Size (diameter) IS 12056:1987 Cl. No. 4.2 1 mm to 10 mm (vehicles Upto 6000 Kg)/ 1mm to 2 mm (vehicles above 6000 Kg) 14. Metallic-fuel tank Leak Tightness Test IS 14681:1999 Cl. No 3.1, 10 kPa to 600 kPa for 2 and 3 W EEC 97/24 Ch.VI Annex-1 Cl. No. 1.3 Leakage Test IS 14681:1999 Cl. No 3.2, 10 ml/minute to EEC 97/24 Ch.VI, Annex-1 100 ml/minute Cl. No. 1.3

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 15. Non-Metallic fuel Permeability Test IS 14681:1999 Cl No 4.1 20 g/day tank for 2 and 3W EEC 97/24 Ch.VI, Cl. No. 2.1.1 Leak Tightness Test IS 14681:1999 Cl No 3.1 5 kPa to 50 kPa EEC 97/24 Ch.VI, Annex-I Cl. No. 1.3 Leakage Test IS 14681:1999 Cl No 3.2 1 ml/minute to EEC 97/24 Ch.VI, Annex-I 100 ml/minute Cl. No. 1.3 at the end of 5 minutes

Shock Test IS 14681:1999 Cl No 4.2 (-) 10 °C to (-) 20 °C EEC 97/24 Ch.VI, Cl. No. 2.2 Mechanical IS 14681:1999 Cl No 4.3 25 °C to 60 °C Strength Test EEC 97/24 Ch.VI, Cl. No. 2.3 0.1 kg/cm2 to 0.5 kg/cm2 Fuel Resistance IS 14681:1999 Cl No 4.4 (±) 25 % Test EEC 97/24 Ch.VI, Cl. No. 2.4 Fire Resistance Test IS 14681:1999 Cl No 4.5 0.1 mm/s to 0.80 mm/s EEC 97/24 Ch.VI, Cl. No. 2.5 High temperature test IS 14681:1999 Cl No 4.6 30 °C to 70 °C EEC 97/24 Cl. No. 2.6

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed

MECHANICAL TESTING

LOCATION 2

I. PERFORMANCE/DURABILITY/SAFETY TEST

1. Seats and their Dynamic test Cl. 5.1, 5.3 of ‘g’ Level Upto 50g, Anchorages (Resistance to Inertia IS 15546:2005 Pulse Width Upto150 ms Effects) Cl. 6.3 of ECE 17.08 (Using Bending bar Cl. 4.2.3, 4.3.3 of AIS-023 sled test facility) Cl. 6.3 of Appendix A of ADR 3/03 Cl. 6.3 of SANS 20017:2004 2. Seats Luggage Retention test Cl. 6.3 of ECE 17.08 ‘g’ Level 24 (±) 4g (Using Bending bar Cl. No. 5.9 of IS15546:2005 Within Specific Corridor, sled test facility) Cl.5.15 of Appendix A of Speed ADR 3/03 49 kmph to 50 kmph, Cl.5.15 SANS 20017:2004 Seat Back Movement wrt R Point Upto 200 mm

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 3. Ambulance Dynamic test Clause 5.0 of AIS-125 ‘g’ Level 10 (±) 2g Stretcher (Resistance to Inertia (Part 1) including Within Specific Corridor Effects) Amendment No. 2 (Using Bending bar sled test facility)

4. Tests on Crash Test Dummies A. Hybrid-III 50%tile Head drop Test Annex 7 of AIS-098 Resultant Acceleration dummy including 225 g to 275 g, Lateral Amendment No. 2 Acceleration (±) 15 g,

Cl. 2.0 and Annex 10 of Unimodal Oscillation < ECE 94.03 10% B. Eurosid-II Dummy Annex 3(B) of AIS-099 Resultant Acceleration including 100 g to150 g Amendment No. 2 Annex 6 of ECE 95.03 C. Hybrid-III 50%tile Neck Flexion Test Annex 7 of AIS-098 Velocity 6.89 m/s to 7.13 dummy including m/s, Acceleration 29 g max, Amendment No. 2 Rotation 64 to 78°, Cl. 2.0 and Annex 10 of Moment ECE 94.03 88.1 Nm to 108.4 Nm Neck Extension Test Velocity 5.94 m/s to 6.19 m/s, Acceleration 22g max, Rotation 81 to 106°, Moment 52.9 Nm to 80 Nm

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed D. Eurosid-II Dummy Neck Test Annex 3(B) of AIS-099 Velocity 3.3 m/s to 3.5 m/s, including Pendulum Velocity within Amendment No. 2 specified corridor, Head Annex 6 of ECE 95.03 Flexion Angle 49 to 59°, Fore and Aft angle 26.8 to 32.5° E. Hybrid-III 50%tile Thorax Impact Test Annex 7 of AIS-098 Velocity 6.59 m/s to 6.83 dummy including m/s, Chest Deflection Amendment No. 2 63.5 mm to 72.6 mm, Cl. 2.0 and Annex 10 of Pendulum Force ECE 94.03 5.16 kN to 5.9 kN, Internal Hysteresis between 69 % to 85 % Knee Impact Test Annex 7 of AIS-098 Velocity 2.07 m/s to 2.13 including m/s, Pendulum Force Amendment No. 2 4.715 kN to 5.782 kN Cl. 2.0 and Annex 10 of ECE 94.03 Knee Slider Impact Annex 7 of AIS-098 Velocity 2.7 m/s to 2.8 m/s, Test including Femur Force Amendment No. 2 1.26kN to 3.1 kN, Cl. 2.0 and Annex 10 of Displacement ECE 94.03 10.2 mm to 17.8 mm Hip Joint Range of Annex 7 of AIS-098 Rate of Torque between Motion Test including Amendment No. 2 5 °/s to 10 °/s, Femur Cl. 2.0 and Annex 10 of Angle between40° to 50°, ECE 94.03 Torque Upto 203 Nm

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Upper Foot Impact Annex 7 of AIS-098 Velocity 6.6 m/s to 6.8 m/s, Test including lower tibia bending Amendment No. 2 momentum about the y- Cl. 2.0 and Annex 10 of axis(My)between ECE 94.03 95 Nm to 145 Nm Lower Foot Impact Velocity4.3 m/s to 4.5 m/s, Test Without Shoe Impactor Acceleration between 245 g to 345 g Lower Foot Impact Velocity6.6 m/s to 6.8 m/s, Test With Shoe Tibia Compressive Force between 2.8 kN to 3.8 kN

F. Eurosid-II Dummy Rib Module Test Annex 3(B) of AIS-099 Velocity 3.96 m/s to 4.04 including Amendment No. 2 m/s, Rib Deflection 46 mm to 51 mm Annex 6 of ECE 95.03 Velocity 1.98 m/s to 2.02 m/s, Rib Deflection 23.5 mm to 27.5 mm Velocity 2.97 m/s to 3.03 m/s, Rib Deflection 36 mm to 40 mm Lumbar Spine Impact Annex 3(B) of AIS-099 Velocity 5.95 m/s to 6.15 Test including Amendment No. 2 m/s, Pendulum velocity Annex 6 of ECE 95.03 within specified corridor, Head FlexionAngle 45 to 55°, ForeandAftangle 26.7 to 34.2°

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Shoulder Impact Test Annex 3(B) of AIS-099 Velocity 4.2 m/s to 4.4 m/s, including Amendment No. 2 Pendulum Acceleration Annex 6 of ECE 95.03 7.5 g to 10.5 g Abdomen Impact Test Annex 3(B) of AIS-099 Velocity3.9 m/s to 4.1 m/s, including Peak Abdomen Force Amendment No. 2 2.2 kN to 2.7 kN, Max Annex 6 of ECE 95.03 Pendulum Force between 4.0 kN to 4.8 kN Pelvis Impact Test Annex 3(B) of AIS-099 Velocity4.2 m/s to 4.4 m/s, including Amendment No. 2 PubicForce Annex 6 of ECE 95.03 1.04 kN to 1.64 kN

5. Passenger Full Frontal Collision Cl. 7 of IS 11939:1996 Speed between vehicles category (Crash) Test (RA 2012) 48.3 kph to 53.1 kph, of M1 and N1, Cl. 5.1 of AIS-096 including Total Vehicle including vehicles Amendment No. 4 Mass Upto 3500 kg equipped with Cl. 5.1 of ECE 12.04 electric power Cl 10.2.2, 10.2.3 and 10.2.4 train of ADR 10/00 SANS 20012:1994/ECE R12:1994 Rev 3 Offset Frontal Cl. 5.2 of AIS-098 including Speed 56 kph to 57 kph, Collision (Crash)Test Amendment No. 2 Total Vehicle Mass Cl. 5.2 of ECE 94.03 Upto 3500 kg Cl. 5.1 of ADR 73/00 SANS 20094:2009/ECE R94:2007 Rev1

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Lateral Collision Cl. 5.2 of AIS-099 including Speed 49 kph to 51 kph, (Crash) Test Amendment No. 2 Total Vehicle Mass Cl. 5.1 of ECE 95.03 Upto 3500 kg Cl. 5.1 of ADR 72/00 Rear Impact (Crash) Cl. 5.0 of AIS-101 including Speed between Test Amendment No. 1 35 kph to 38 kph, Total Vehicle Mass 3500 kg 6. Front &Rear Vehicle Impact Test Cl. No. 4.2 of Speed: Bumpers of IS 15901-2010 min.:4km/h for center vehicle Annex-3 Cl. No. 2.7.5 & impact (Vehicle testing) 2.8.4 of ECE 42.00 min:2.5km/h for corner impact

7. Interior fittings Head Form Impact Annex-4 Cl. No. 1.4.2 & 2.1 Velocity:min. 24.1 Km/h Test (Using Occupant of ECE 21.01 Annex-B, Deceleration:80g Impact test Rig) Cl. No. B-1.4.2 & B-2.1 of IS 15223:2002 Appendix A, Annex-4 Cl. No. 1.4.2 &2.1 of ADR 21 SANS 20021:1993 Impact Test (Pendulum Annex-4 Cl. No. 1.4.2 & 2.1 Velocity:min. 24.1 Km/h Impactor) of ECE R 21.01 Deceleration:80g&3 (Using Universal Annex-B, Cl. No. B-1.4.2 & milliseconds Launcher-Pedestrian B-2.1 of IS 15223:2002 test facility) Appendix A, Annex-4 Cl. No. 1.4.2 & 2.1 of ADR 21 SANS 20021:1993 8. Steering control Body Block Test Cl. No. 5.2 of ECE R 12.04, Velocity:min. 24.1 Km/h

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed assembly (Using Occupant Cl. No. 6.1 of IS Force:11150 N Impact test Rig) 11939:1996 (RA 2012) Deceleration:120 g Cl. No. 5.2of AIS 096 Appendix-A Cl.No. 5.2 of ADR10 SANS 20012:1994 9. Steering control Body Block Test Cl. No. 5.2 of ECE R 12.04, Velocity:min. 24.1 Km/h assembly Cl. No. 6.1 of IS Peak Horizontal Force: (Using Universal 11939:1996 (RA 2012) 11150 N Methods: Launcher-Pedestrian Cl. No. 5.2 of AIS 096 Tri-axial Load Cell test facility) Appendix-A Cl.No. 5.2 Accelerometers of ADR10 SANS 20012:1994

Head Form Test Cl. No. 5.3 of ECE R 12.04, Velocity:min. 24.1 Km/h Cl. No. 8.1 of IS (Using Universal 11939:1996 (RA 2012) Deceleration:80 g & 3 Launcher-Pedestrian Cl. No. 5.3 of AIS 096 Milliseconds test facility) Appendix-A Cl.No. 5.3 of ADR10 SANS 20012:1994 Max.Acceleration:120 g 10. Pedestrian safety

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed A. Front structure of Pedestrian Child head Cl. 5.2. & 7.3 of AIS 100 HIC≤1000 & HIC≤1700 Passenger cars form test Appendix-5 Cl.4 & Cl. 5.2 of Child Head form test area. ECE 127.02 Speed-9.7 (±) 0.2 m/s. Cl. 5.2. & 7.3 of GTR-9 Mass 3.5 (±) 0.07Kg Amendment 1 Impact Angle-50º (±) 2 º Target accuracy- (±) 10mm Temperature-20 (±) 4ºc Humidity-40 (±) 30% Pedestrian Adult head Cl. 5.2. & 7.4 of AIS 100 HIC≤1000 & HIC≤1700 form test Appendix-5 Cl.5 & Cl. 5.2 of Adult Head form test area. ECE 127.02 Speed-9.7 (±) 0.2 m/s. Cl. 5.2. & 7.3 of GTR-9 Mass 4.5 (±) 0.1Kg Impact Amendment 1 Angle-65º (±) 2 º Target accuracy- (±) 10mm Temperature-20 (±) 4ºc Humidity-40 (±) 30%

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Pedestrian Upper leg Cl. 7.1.2 & Cl 5.1 of AIS 100 Sum of Impact forces< form test Appendix-5 Cl.2 & Cl. 5.1.2 7.5kN, Bending of ECE 127.02 moment<510Nm, Speed Cl. 7.1.2 & Cl 5.1 of GTR-9 11.1 (±) 0.2 m/s. Amendment 1 Mass 9.5 kg (±) 0.1 kg. Target accuracy-Vertical plane-±2 º Lateral and vertical tolerance (±) 10m Pedestrian Lower leg Cl. 7.1.1 & Annex 5 Cl. 5.1 Dynamic Knee form test of AIS 100 bending<19°, Appendix-5 Cl.1 & Cl. 5.1.1 Knee Shear Displacement of ECE <6mm, Tibia 127.02 Acceleration<250g, Speed Cl. 7.1.1 & Annex 5 Cl. 5.1 11.1 (±) 0.2 m/s Mass-13.4 of GTR-9 (±) 0.2 kg Target accuracy- Amendment 1 Horizontal plane-(±) 2 º Longitudinal plane-(±) 2 º Lateral plane- (±) 2º About Vertical axis- (±) 5 º Lateral and vertical tolerance (±) 10mm II. MECHANICAL PROPERTIES OF MOTELS

1. Ferrous & Non- Tensile test at room ASTM E8/ E8M-2016a For YS, UTS, MoE: Ferrous temp. (Offset YS, Load:1 kN to 100 kN Upper & Lower YS, For Elongation:1 % to 80 % UTS,% Elongation) Modulus of Elasticity ASTM E111-2017

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed Rockwell Hardness IS 1586 (P.1):2012 30 HRBW to 100 HRBW 25 HRC to 65 HRC 2. Carbon steels and Inclusion Content of IS 4163:2004 100X By Comparison with Alloy steel Steel standard Diagram Grain size analysis IS 4748:2009 100X By Comparison with (Ferritic-untwinned standard Diagram Grain Size) Grain size 00-10 Depth of ASTM E1077-2014 100X decarburization (5 µm to 1200 µm) 3. 5th wheel coupling a) S t a t i c te s t -1 AIS 091/Part1,2009 Load: 50 KN to 500 KN and mounting Limit of deformation & ECE R 55,2018 plate width under specified Annexure 6 clause load No.3.7.2.2 b) S t a t i c te s t -2 Separation of coupling pin under specified load D yna m i c te st AIS 091/Part 1,2009 Horizontal force = Number of cycles for & ECE R 55,2018 20 kN to 220 kN test pass or fail Annexure 6 clause Vertical force = Horizontal force and No.2.2 and 3.7.3.1 50kN to 500 kN vertical force 4. 5th Wheel D yna m i c te st AIS 091/P 1,2009 & ECE R Load: 50 KN to 500 KN King Pin Number of cycles for 55,2018 Annexure 5 test pass or fail clause 8 Annexure 6 clauseNo.2.2 and 3.9 5. Metals and A x i a l F a t i gue T e st: ASTME466-15 Load: 20 kN to 90 kN Alloys Number of cycles for test pass or fail Fatigue life estimation (S-N Curve)

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed III. METALLOGRAPHY TEST

1. Microstructure analysis AML/TP/020 50X to 1000X by Optical Microscope (Ref. ASM ATLAS Vol. and Scanning Electron 9,11,12) Microscope Evaluation of Elements AML/TP/038 Qualitative analysis of by Energy Dispersive (Ref. ASM ATLAS Vol. 9, Elements B,C,N, O,F, Na, Analysis (EDS) on SEM 11, 12) Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni,Cu,Zn,Br, Sr,Zr,Nb, Mo,Rh,Ag, Cd,Sn,Sb, Ba,W,Pt,Au, Pb when present at % level

IV. PLASTICS & PLASTIC PRODUCTS

1. Plastic Materials Tensile test of plastics ASTM D638-2014 50 N to 100 kN (Room temp.) Elongation Range: (YS, TS & Elongation) 1 % to 100% Flexural strength of ASTM D790:2017 50 N to 100 kN Plastics (Room Temp.)

V. RUBBER & RUBBER PRODUCTS

1. Rubber Materials Compression Set Test ASTM D395-16 Deflection: Upto 25% for Rubber Test Method B Temp:50 ºC to 200 ºC Tensile strength of ASTM D412-16 Method A 50 N to 1000 N rubber

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed

PHOTOMETRY TESTING

LOCATION 1

I. LIGHT SOURCES (ELECTRIC LAMP)

1. Head lamp Light distribution and AIS 010 (Part 1, 2 and 4)- 1 lx to 300 lx Colour Measurement in Rev. 1-Dec. 2010 0.001 co-ordinates to a) driving beam, AIS 010 (Part 5)- 0.5 co-ordinates (x and y) b) passing beam Rev. 1-Dec. 2010 ECE R-112 (Oct. 2008), ECE R 113 (July 2009) ADR 46/00 2006 2. Stop lamp i) Light distribution AIS 010 (Part 3)- 1 cd to 1000 cd 3. Front Position ii) Colour measurement Rev. 1-Dec. 2010 0.001 co-ordinates to (side) lamps and iii) Illumination area AIS 010 (Part 5)- 0.5 co-ordinates (x and y) Front end-outline Rev. 1-Dec. 2010 marker lamps AIS 012 (Part 6)- 4. Front position Rev. 1-Dec. 2010 (side) lamps ECE R-50 (Oct. 2008) incorporated in ECE R-7 (Mar. 2009) head lamps ADR 53/00 2006 5. Rear Position ADR 49/00 2006 (side) lamps and ADR 60/00 2006 Rear end-outline SANS 20050-2007 marker lamps SANS 20007-2002

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed 6. Direction i) Light distribution AIS 010 (Part 3)- 1 cd to 1000 cd indicator ii) Colour measurement Rev. 1-Dec. 2010 0.001 co-ordinates to iii) Illumination area AIS 010 (Part 5)- 0.5 co-ordinates (x and y) Rev. 1-Dec. 2010 AIS 012 (Part 5)- Rev. 1-Oct. 2011 ECE R-50 (Oct. 2008) ECE R-6 (Mar. 2009) ADR 6/00 2005 ADR 53/00 2006 SANS 20050-2007 SANS 20006-2003 7. Reverse lamp i) Light distribution AIS 010 (Part 3)- 1 cd to 1000 cd ii) Colour measurement Rev. 1-Dec. 2010 0.001 co-ordinates to iii) Illumination area AIS 010 (Part 5)- 0.5 co-ordinates (x and y) Rev. 1-Dec. 2010 AIS 012 (Part 7)- Rev. 1-Oct. 2011 ECE R-50 (Oct. 2008) ECE R-23 (Oct. 2008) ADR 53/00 2006 ADR 1/00 2005 SANS 20050-2007 SANS 20023-2012 8. Front Fog lamp i) Light distribution AIS 012 (Part 1)- 1 cd to 1000 cd ii) Colour Rev. 1-Oct. 2011 0.001 co-ordinates to AIS 010 (Part 5)- 0.5 co-ordinates (x and y) Rev. 1-Dec. 2010 ECE R-19 (Mar. 2009)

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed

9. Rear fog lamp i) Light distribution AIS 012 (Part 2)- 1 cd to 1000 cd ii) Colour measurement Rev. 1-Oct. 2011 0.001 co-ordinates to iii) Illumination area AIS 010 (Part 5)- 0.5 co-ordinates (x and y) Rev. 1-Dec. 2010 ECE R-38 (Oct. 2008) ADR 52/00 2006 II. LUMINARIES

1. Number plate i) Luminance AIS 010 (Part 3)- 1 cd/m2 to 1000 cd/m2 lamp distribution Rev. 1-Dec. 2010 ii) Gradient of AIS 010 (Part 5)- Luminance Rev. 1-Dec. 2010 AIS 012 (Part 4)- Rev. 1-Oct. 2011 AIS 62(Dec. 2004) ECE R-50 (Oct. 2008) ECE R-4 (July 2008), ADR 53/00 2006 ADR 48/00 2006 SANS 20050-2007 SANS 20004-2012 2. Filament lamp I) Electrical AIS 034 (Part 1)- 1 lm to 5000 lm Test measurements Rev. 1-Dec. 2010 0.1 VDC to 30 VDC i) Photometric ECE R-37 (Oct. 2009) 0.01 A to 10 A measurements ADR 51/00 2006 0.001 co-ordinates to 0.5 ii) Colour measurement SANS 20037-2007 co-ordinates (x and y)

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager Laboratory The Automotive Research Association of India, S. No. 102, Vetal Hill, Off.Paud Road, Kothrud, Pune, Maharashtra

Validity 31.10.2018 to 30.10.2020 Last Amended on 03.11.2018

Sl. Product / Material Specific Test Test Method Specification Range of Testing / of Test Performed against which tests are Limits of Detection performed

III. GLASSES/MIRRORS

1. Reflex Reflector i) Photometric AIS 057-Rev. 1-Dec. 2010 1 mcd/lx to 50000 mcd/lx and Warning Measurement AIS 22 (May 2001), 0.001 co-ordinates to Triangle. (Co-efficient of ECE R27(Feb. 2007) 0.5 co-ordinates (x and y) Luminous Intensity) ECE R3(Feb 1998) ii) Colour measurement ADR 47/00 2006 SANS 20027-1998 SANS 20003-2005 2. Safety Glass i) Light Transmission IS 2553 (Part II) 1 % to 100 % ii) Optical distortion ECE R-43 (Aug. 2007), 0.4 Minutes to 8 Minutes of SANS 20043-2005 arc Visual iii) Image Separation ABNT NBR 9503 ABNT NBR 9504

Birendra Prasad Murmu N. Venkateswaran Convenor Program Manager