Installation Guide Ds4+

Home , Volkswagen Jetta, Volkswagen Jetta (A1), Volkswagen Jetta (A2), Volkswagen Jetta (A5), Volkswagen Jetta (A6), Volkswagen Jetta (A7)

INSTALLATION GUIDE DS4+

VW10

This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components. 2017-11-02 Contents Warning! Safety first...... 3 Introduction...... 4 Pre-installation and application warnings...... 4 Vehicle application guide...... 5 Wiring connections...... 6 Main harness (H1), 12-pin black connector...... 6 Relay harness (H2), 10-pin white connector...... 6 Data harness (H3), 8-pin white connector...... 6 Analog input/output harness (H4), 22-pin white connector...... 7 RF Port harness (H5), 2-pin white connector...... 7 D2D harness (H6), 4-pin white (1) and black (2) connectors...... 7 Temperature sensor harness (H7), 2-pin black connector...... 7 Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)...... 8 Type 1...... 8 Type 2...... 11 Type 3...... 14 Type 4...... 16 Type 5...... 18 Type 6...... 20 Type 7...... 22 Type 8...... 24 Type 9...... 26 Type 10...... 29 Type 11...... 31 Immobilizer interface ...... 33 Method 1: Key Wrap...... 33 Method 2: Immobilizer interface with 556U (Regular Key)...... 33 Method 3: Immobilizer interface with OEM Immobilizer Receiver...... 34 Connecting the module...... 35 Important!...... 35 RF Systems...... 35 8504D Combo Sensor...... 35 When used in conjunction with SmartStart...... 36 D2D port configuration...... 36 Module programming...... 37 LED diagnostics and troubleshooting...... 38 Soft reset...... 40 Hard reset...... 40 Learning the Tach (not needed with Virtual Tach)...... 41 Initializing Virtual Tach (not needed with hardwired or data tach applications)...... 41 Limited lifetime consumer warranty...... 42 Quick Reference Guide...... 43 Warning! Safety first The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: • Never use a test light or logic probe when installing this unit. Always use a multimeter. • Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). • When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle. • USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.

Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle.

This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk.

3 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Introduction The VW10 firmware for DS4+ is compatible with specific Volkswagen and Audi vehicles. It is a complete solution for remote start, security (when security features are enabled), bypass, and features built in Bluetooth 4.0 allowing you to configure and control your system. This guide provides information on the installation of the module using VW10. Please refer to the DirectLink application or www.directechs.com for more information about which configuration is best for your application.

Warning! This module is designed to be configured using the DirectLink application for mobile devices, however it can also be configured using the web tool located at www.directechs.com. To download the DirectLink mobile application, please visit the Google Play or Apple store.

Pre-installation and application warnings

Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness Keys required for Keys required for compatible programming 1 operation 1

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector. It is important to check that the fuses are positioned correctly in the module. Refer to the "Fuse selection" section following each installation type for more information. Refer to the "Vehicle wiring reference chart" following each installation type.

General notes: This section highlights important information for this specific firmware.

[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are not equipped with a factory hood pin. [2] The siren is ONLY required when enabling the security features during module flashing. [3] For Key Wrap instructions, refer to pages 33 & 34. [4] Locks and trunk release output ONLY required if door locks or trunk are not supported in data. [5] Diodes and brake connection only required on vehicles where brake needs to be depressed to start.

Additional parts required (maximum required):

87a 86 85 Diode 6A 30 Resistor 100Ω Fuse 7.5A 2 x 1A Diodes 0 x Resistor 2 x Fuse 2 x Relay

4 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Vehicle application guide The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.

Vehicles 2017 2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2004 PK-Universal RF Bypass- Key Req'd AV-Parking Lights Control Security Factory DL-Arm Security Factory DL-Disarm Control Lock DL-Door Unlock DL-Door Unlock Priority DL-Driver DL-Trunk / Hatch Release remote OEM with alarm aftermarket of FOB-Control Remote) OEM using control (Start START LOCK RS-3x RS-3x LOCK STOP (Stop control using OEM Remote) RS-Accessory Activation Activation RS-Ignition RS-RAP Shut Down (Retained ACC Power) RS-SmartStart RS-Start (Crank) Activation Output RPM / RS-Tach Pins Door ALL Monitoring SS-Entry Pin Hood Monitoring SS-Entry Pin Trunk/Hatch Monitoring SS-Entry ST-Brake Status (foot brake) Status Locks ST-Door Status ST-E-Brake Status ST-Ignition Audi A3 4 4 4 4 4 8 8 8 8 • • • • • • • • • • • • • • • • • • • • • • • • Q3 5 5 5 • • • • • • • • • • • • • • • • • • • • • • • • R8 4 4 4 4 8 8 • • • • • • • • • • • • • • • • • • • • • • • • TT 4 4 4 4 4 4 8 8 8 8 • • • • • • • • • • • • • • • • • • • • • • • • Volkswagen 17 16 15 14 13 12 11 10 09 08 07 06 04 EOS 1 1 1 1 1 9 9 9 9 • • • • • • • • • • • • • • • • • • • • • • • • Golf 2 2 2 2 2 9 9 9 9 • • • • • • • • • • • • • • • • • • • • • • • • GTI 2 2 2 2 2 9 9 9 9 • • • • • • • • • • • • • • • • • • • • • • • • Jetta 11 11 11 3 3 3 3 9 9 9 9 9 • • • • • • • • • • • • • • • • • • • • • • • • Jetta GLI 1 1 1 • • • • • • • • • • • • • • • • • • • • • • • • Jetta SportWagen 1 1 1 1 7 9 • • • • • • • • • • • • • • • • • • • • • • • • Passat 2 2 2 2 2 2 10 10 10 10 10 • • • • • • • • • • • • • • • • • • • • • • • • Passat CC 6 6 6 6 6 6 10 10 • • • • • • • • • • • • • • • • • • • • • • • • Rabbit 9 9 9 9 • • • • • • • • • • • • • • • • • • • • • • • • Tiguan 1 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • • • • • •

Legend: AV: Horn and Light Controls DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status

Main harness (H1), 12-pin black connector

Conn./Pin Color Description H1/1 Blue/White Relay 1 N.C. – Parking Light Interrupt (conn. side) 1 H1/2 Blue/Red Relay 1 N.O. – (+) Parking Light Output or (+)12V Input 1 H1/3 Blue Relay 1 COM – (+) Parking Light Interrupt (vehicle side) 1 H1/4 White/Brown Relay 3 N.C. – No Connection1 H1/5 White Relay 3 COM – (+) Accessory Output 1 H1/6 Red (+) 12 Volt (Input) H1/7 Lt. Green/Red Relay 2 N.O. – Key Wrap 1 H1/8 Lt. Green Relay 2 COM – Key Wrap1 H1/9 Lt. Green/White Relay 2 N.C. – Key Wrap 1 H1/10 Black (-) Ground H1/11 White Relay 3 COM – (+) Accessory Output 1 H1/12 Red (+) 12 Volt (Input)

Relay harness (H2), 10-pin white connector

Conn./Pin Color Description H2/1 N/A No Connection H2/2 Red/Black No Connection H2/3 Pink/Black No Connection H2/4 Pink/White No Connection H2/5 Red No Connection H2/6 Green No Connection H2/7 Violet No Connection H2/8 Orange No Connection H2/9 Red/White No Connection H2/10 Pink No Connection

Data harness (H3), 8-pin white connector

Conn./Pin Color Description H3/1 Tan HS CAN Low H3/2 Tan/Black HS CAN High H3/3 Orange/Brown FT CAN Low H3/4 Orange/Green FT CAN High H3/5 Lt. Green No Connection H3/6 Violet/Brown (MUX) Lock/Unlock Output H3/7 Orange/Black ISO BUS 2 H3/8 Yellow/Black ISO BUS 1

1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.

Conn./Pin Color Description H4/1 Lt. Green/Black (-) Hazards Output 1 H4/2 Blue/White (-) Key Release Output 1 H4/3 Dk. Green/Black (-) Lock Output 1 H4/4 Red/White (-) Trunk Release Output 1 H4/5 Brown/Black (-) Horn Output 1 H4/6 Brown/White N/A H4/7 White (+) Starter Output 1 H4/8 Violet/Black (+) Ignition Output 1 H4/9 Dk. Blue/Black (-) Unlock Output 1 H4/10 Lt. Blue/Black (-) FAD Output 1 H4/11 Brown/Red (+) Siren Output 1 H4/12 Pink (+) Ignition Sense Input H4/13 Violet (+) Door Sense Input 2 H4/14 Brown (+) Brake Input 2 H4/15 White/Blue (-) Activation Input 2 H4/16 Blue/Red (-) Valet Switch 2 H4/17 Black/White (-) E-Brake Input 2 H4/18 Orange/Black (-) Instant Alarm Trigger Input 2 H4/19 Blue (-) Trunk Sense Input 2 H4/20 Green (-) Door Sense Input 2 H4/21 Gray (-) Hood Pin Input 2 H4/22 Violet/White (AC) Tach Input

RF Port harness (H5), 2-pin white connector

Conn./Pin Color Description H5/1 N/A RF Loop H5/2 N/A RF Loop

D2D harness (H6), 4-pin white (1) and black (2) connectors

Conn./Pin Color Description H6/1 Blue (Data) TX H6/2 Black (-) Ground H6/3 Green (Data) RX H6/4 Red (+) 12 Volt

Temperature sensor harness (H7), 2-pin black connector

Conn./Pin Color Description H7/1 Black Temperature Sensor H7/2 Black Temperature Sensor

1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a list of compatible features. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary.

7 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Installation (wiring diagrams, fuse selection & vehicle wiring reference charts) Type 1 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).

C B A

FT CAN Low: Orange/Brown, pin 3

FT CAN High: Orange/Green, pin 4

(+) Starter: Red/Black or HS CAN High: Orange/Black, pin 6 Red/Brown,pin 6 Diagnostic 1 8 Connector 1 6 8 Steering column module OBDII 9 16 9 14 16 (behind steering column trim)

(+) Ignition: HS CAN Low: Orange/Brown, pin 14 Black, pin 14 VESCM - Driver side under dashboard [5] Diode 1A

HS CAN 1 Low: Tan: 1

(+) Brake: Black/Red, pin 17 2 HS CAN 1 High: Tan/Black: 2 (+) 12V: 8 FT CAN Low: Orange/Brown: 3 Red/Yellow, 42 25 1 [5] Diode 1A

4 pin 42 5

FT CAN High: Orange/Green: 4 MAIN (5A) (+) (5A) MAIN

(+) Starter / Brake Activation Output: White: 7

(-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-)

28 30

29 12 (+) Ignition Output: Violet/Black: 8 (+) (30A) START & ACC (-) 4

5 20

22 MAIN (5A) (+) (5A) MAIN

(+) Siren Output: Brown/Red: 11 (+) (20A) RLY FLEX (-) 20

(-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) Hood Pin (+) (20A) IGN Siren

(-) Hood Input: Gray: 21 4 DS4+ DS4 Parking Light Interrupt (conn. side): Blue/White: 1 (+) Parking Light Output: Blue/Red: 2 52 41 24 11 Proper Fuse Brown VESCM connector C Parking Light Interrupt (vehicle side): Blue: 3 Positioning 2 (+) 12V Input: Red: 6 & 12

Key Wrap: Lt.Green/Red: 7 12 Key Wrap: Lt. Green: 8 Key Wrap: Lt. Green/White: 9 DS4 (-) Ground: Black: 10 Parking Lights Interrupt: Red/White or Red/Blue, pin 8

CUT 10 10 8 7 6 Headlight switch 9 Slide (black conn. at DS4+ 5 4 3 2 1 light switch) to open

(+) Parking Lights: Gray/Yellow, pin 3 It is important to check that the fuses are positioned correctly.

DS4+ VW10 8 © 2017-11-02 Directed. All rights reserved. Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Volkswagen EOS 2010-2014 Parking Light Gray/Yellow 3 (+) Headlight Switch. Black 10 A Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A Starter Red/Brown or Red/Black 6 (+) Steering column module. Black 16 B Ignition Black 14 (+) Steering column module. Black 16 B FT CAN High Orange/Green 4 Data Steering column module. Black 16 B FT CAN Low Orange/Brown 3 Data Steering column module. Black 16 B HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C 12V Red /Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D Volkswagen Jetta GLI 2012-2014 Parking Light Gray/Yellow 3 (+) Headlight Switch. Black 10 A Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A Starter Red/Brown or Red/Black 6 (+) Steering column module. Black 16 B Ignition Black 14 (+) Steering column module. Black 16 B FT CAN High Orange/Green 4 Data Steering column module. Black 16 B FT CAN Low Orange/Brown 3 Data Steering column module. Black 16 B HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C 12V Red /Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D

9 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Volkswagen Jetta SportWagen 2011-2014 Parking Light Gray/Yellow 3 (+) Headlight Switch. Black 10 A Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A Starter Red/Brown or Red/Black 6 (+) Steering column module. Black 16 B Ignition Black 14 (+) Steering column module. Black 16 B FT CAN High Orange/Green 4 Data Steering column module. Black 16 B FT CAN Low Orange/Brown 3 Data Steering column module. Black 16 B HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C 12V Red /Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D Volkswagen Tiguan 2010-2016 Parking Light Gray/Yellow 3 (+) Headlight switch. Black 10 A Parking Light Interrupt Red/Blue 8 Cut Headlight switch. Black 10 A Ignition Black 14 (+) Steering column module behind steering column trim. Black 16 B Starter Red/White or Red/Black 6 (+) Steering column module behind steering column trim. Black 16 B FT CAN High Orange/Green 4 Data Steering column module behind steering column trim. Black 16 B FT CAN Low Orange/Brown 3 Data Steering column module behind steering column trim. Black 16 B HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C 12V Red/Violet 42 (+) VESCM connector C, under drivers dash. Brown 52 D Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D

10 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Type 2 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).

C B A

FT CAN Low: Orange/Brown, pin 3

FT CAN High: Orange/Green, pin 4

(+) Starter: Red/Black or HS CAN High: Orange/Black, pin 6 Red/Brown,pin 6 Diagnostic Connector 1 8 1 6 8 Steering column module OBDII 9 16 9 14 16 (behind steering column trim)

(+) Ignition: HS CAN Low: Orange/Brown, pin 14 Black, pin 14 VESCM - Driver side under dashboard [5] Diode 1A

HS CAN 1 Low: Tan: 1

(+) Brake: Black/Red, pin 17 2 (+) 12V: HS CAN 1 High: Tan/Black: 2 Red/White or 8 FT CAN Low: Orange/Brown: 3 Red/Yellow, 42 25 1 [5] Diode 1A

4 pin 42 5

FT CAN High: Orange/Green: 4 MAIN (5A) (+) (5A) MAIN

(+) Starter / Brake Activation Output: White: 7

(-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-)

28 30

29 12 (+) Ignition Output: Violet/Black: 8 (+) (30A) START & ACC (-) 4

5 20

22 MAIN (5A) (+) (5A) MAIN

(+) Siren Output: Brown/Red: 11 (+) (20A) RLY FLEX (-) 20

(-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) Hood Pin (+) (20A) IGN Siren

Key Wrap: Lt.Green/Red: 7 12 Key Wrap: Lt. Green: 8 Key Wrap: Lt. Green/White: 9 DS4 Parking Lights Interrupt: (-) Ground: Black: 10 Red/White, pin 8

CUT 10 10 8 7 6 Headlight switch 9 Slide (black conn. at DS4+ 5 4 3 2 1 light switch) to open

(+) Parking Lights: White/Black, pin 1 It is important to check that the fuses are positioned correctly.

DS4+ VW10 11 © 2017-11-02 Directed. All rights reserved. Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Volkswagen Golf 2010-2014 Parking Light White/Black 1 (+) Headlight Switch. Black 10 A Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A Ignition Black 14 (+) Steering column module. White 16 B Starter Red/Black or Red/Brown 6 (+) Steering column module. White 16 B FT CAN High Orange/Green 4 Data Steering column module. White 16 B FT CAN Low Orange/Brown 3 Data Steering column module. White 16 B HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C 12V Red/White or Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D Volkswagen GTI 2010-2014 Parking Light White/Black 1 (+) Headlight Switch. Black 10 A Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A Ignition Black 14 (+) Steering column module. White 16 B Starter Red/Black or Red/Brown 6 (+) Steering column module. White 16 B FT CAN High Orange/Green 4 Data Steering column module. White 16 B FT CAN Low Orange/Brown 3 Data Steering column module. White 16 B HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C 12V Red/White or Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D

12 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Volkswagen Passat 2012-2017 Parking Light White/Black 1 (+) Headlight Switch. Black 10 A Parking Light Interrupt Red/White or Red/Yellow 8 Cut Headlight Switch. Black 10 A Ignition Black 14 (+) Steering column module. Black 16 B Starter Red/Black or Red/Brown 6 (+) Steering column module. White 16 B FT CAN High Orange/Green 4 Data Steering column module. Black 16 B FT CAN Low Orange/Brown 3 Data Steering column module. Black 16 B HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C 12V Red/White or Red /Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D

13 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Type 3 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).

White VESCM Connector B VESCM - (under drivers kick) (under drivers kick) 16 3 7 73 HS CAN High: Orange/Black, pin 6

1 8 Diagnostic

9 16 Connector OBDII FT CAN Low: Orange/Brown, pin 21 HS CAN Low: Orange/Brown, pin 14 FT CAN High: Orange/Green, pin 20

1 17 63 Connector Connector HS CAN 1 Low: Tan: 1 A B HS CAN 1 High: Tan/Black: 2 2

FT CAN Low: Orange/Brown: 3 8

FT CAN High: Orange/Green: 4

5 5 5 5 5 4 5 5 5 5 5 5 5 5 5 5 5 5

(MUX) Lock/Unlock Output: Violet/Brown: 6 5

MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN

15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15

(-) Trunk Release Output: Red/White: 4 15

(-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-) (-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-) (-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-)

30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30

(+) Starter / Brake Activation Output: White: 7 30

(-) ACC & START (30A) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (-) ACC & START (30A) (+) (30A) START & ACC (-) (-) ACC & START (30A) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (-) ACC & START (30A) (+) (30A) START & ACC (-)

(-) ACC & START (30A) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-)

16 3 7 73 4 (+) (30A) START & ACC (-)

5 5 5 5 5 5 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20

(+) Ignition Output: Violet/Black: 8 20

MAIN (5A) (+) (5A) MAIN (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN

(-) FLEX RLY (20A) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (-) FLEX RLY (20A) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (-) FLEX RLY (20A) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-)

Diode 1A Diode 1A

15 15 15 15 15 15

20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20

(+) Siren Output: Brown/Red: 11 20

(+) 12V: Hood Pin (+) (20A) IGN (MUX) Doorlock: Siren Red/White (-) Hood Input: Gray: 21 4 Blue/Red,pin 24 or Red/Yellow, pin 68 DS4+ DS4 (-) Trunk Release: (+) 12V Input: Blue/Red: 2 Violet, pin 23 Proper Fuse (+) Brake: (+) Parking Light Output: Blue: 3 Positioning 2 Black/Red, pin 39 (+) Accessory Output: White: 5 & 11

(+) 12V Input: Red: 6 & 12 12 1 17 63 Key Wrap: Lt.Green/Red: 7 Key Wrap: Lt. Green: 8 Black VESCM connector A DS4 (under drivers kick) Key Wrap: Lt. Green/White: 9 (-) Ground: Black: 10

(+) Parking Lights: (+) Starter: Red/Black, pin 4 Gray/Red, pin 14 10 (+) Ignition: 10 14 17 Black/Violet, pin 8 Slide DS4+ to open

1 9

Ignition Switch 10 9 8 7 6 It is important to check that the (black conn. at Parking Light Switch fuses are positioned correctly. 5 4 3 2 1 ignition switch) (black conn. at light switch) (+) Accessory: Black/Red, pin 3

DS4+ VW10 14 © 2017-11-02 Directed. All rights reserved. Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Volkswagen Jetta 2011-2014 Starter Red/Black 4 (+) Ignition switch. Black 10 A Ignition Black/Violet 8 (+) Ignition switch. Black 10 A Accessory Black/Red 3 (+) Ignition switch. Black 10 A HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 B HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 B Parking Light Gray/Red 14 (+) Headlight switch. Black 17 C FT CAN High Orange/Green 20 Data VESCM connector B, under drivers dash. White 73 D FT CAN Low Orange/Brown 21 Data VESCM connector B, under drivers dash. White 73 D 12V Red/White or Red/Yellow 68 (+) VESCM connector A, under drivers dash. Black 73 E Brake Black/Red 39 (+) VESCM connector A, under drivers dash. Black 73 E Doorlocks [4] Blue/Red 24 MUX VESCM connector A, under drivers dash. Black 73 E Trunk Release [4] Violet 23 (-) VESCM connector A, under drivers dash. Black 73 E

15 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Type 4 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).

C B A

FT CAN High: Orange/Green, pin 14 Steering Column Control Unit FT CAN Low: Orange/Brown, pin 15 HS CAN High: Orange/Black, pin 6 Steering Column Module (behind steering 1 20 Diagnostic 10 17 1 8 column trim) Connector 9 16 (+) Ignition: Pin 17 (+) Starter: Red/Black OBDII or Black/Gray,pin 18

HS CAN Low: Orange/Brown, pin 14 Black VESCM connector A VESCM - Driver side under dashboard 42 25 1 [5] Diode 1A

HS CAN Low: Tan: 1 28

29 12 2 HS CAN High: Tan/Black: 2 8 (-) Parking Lights: FT CAN Low: Orange/Brown: 3 Black/White, pin 19

FT CAN High: Orange/Green: 4 5 MAIN (5A) (+) (5A) MAIN

(-) Parking Lights Output: Lt.Green/Black: 1

(-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-) (+) Starter / Brake Activation Output: White: 7 30 52 41 24 11

(+) Ignition Output: Violet/Black: 8 (+) (30A) START & ACC (-) 4 5 20

22 MAIN (5A) (+) (5A) MAIN

(+) Siren Output: Brown/Red: 11 (+) (20A) RLY FLEX (-)

(-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) Hood Pin (+) (20A) IGN Siren (-) Hood Input: Gray: 21 DS4+ DS4 4 (+) 12V Input: Red: 6 & 12 (+)12V: Red/Blue or Red/Violet, pin 42 Proper Fuse

Key Wrap: Lt.Green/Red: 7 2 42 25 1 Positioning Key Wrap: Lt. Green: 8 12

Key Wrap: Lt. Green/White: 9 28 29 12 DS4 (-) Ground: Black: 10

[5] Diode 1A

(+) Brake: Black/Red, pin 17 10

52 41 24 11 Slide DS4+ Brown VESCM connector C to open

It is important to check that the fuses are positioned correctly.

DS4+ VW10 16 © 2017-11-02 Directed. All rights reserved. Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Audi A3 2009-2013 HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A Starter Red/Black 18 (+) Steering column module behind steering column trim. Black 20 B Ignition Black/Green 17 (+) Steering column module behind steering column trim. Black 20 B FT CAN High Orange/Green 14 Data Steering column module behind steering column trim. Black 20 B FT CAN Low Orange/Brown 15 Data Steering column module behind steering column trim. Black 20 B 12V Red/Blue 42 (+) VESCM, connector C, under drivers dash. Brown 52 C Brake Black/Yellow 17 (+) VESCM, connector C, under drivers dash. Brown 52 C Parking Lights Gray/Yellow 19 (-) VESCM, connector A, under drivers dash. Black 52 D Audi R8 2010-2014 HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A Starter Black/Gray 18 (+) Steering column module behind steering column trim. Black 20 B Ignition Black/Violet 17 (+) Steering column module behind steering column trim. Black 20 B FT CAN High Orange/Green 14 Data Steering column module behind steering column trim. Black 20 B FT CAN Low Orange/Brown 15 Data Steering column module behind steering column trim. Black 20 B 12V Red/Violet 42 (+) VESCM, connector C, below glove box. Brown 52 E Brake Red/Black 17 (+) VESCM, connector C, below glove box. Brown 52 E Parking Lights Black/White 19 (-) VESCM, connector A, below glove box. Black 52 F Audi TT 2010-2015 HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A Starter Red/Black 18 (+) Steering column module behind steering column trim. Black 20 B Ignition Black/White 17 (+) Steering column module behind steering column trim. Black 20 B FT CAN High Orange/Green 14 Data Steering column module behind steering column trim. Black 20 B FT CAN Low Orange/Brown 15 Data Steering column module behind steering column trim. Black 20 B 12V Red/Violet 42 (+) VESCM, connector C, under drivers dash. Brown 52 C Brake Black/Yellow 17 (+) VESCM, connector C, under drivers dash. Brown 52 C Parking Lights Gray/Yellow 19 (-) VESCM, connector A, under drivers dash. Black 52 D

17 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Type 5 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( )

C B A

FT CAN Low: Orange/Brown, pin 3

HS CAN High: Diagnostic FT CAN High: Orange/Green or Lt.Green, pin 4 Orange/Black, pin 6 Connector OBDII (+) Starter: Red/Black,pin 6 1 8

9 16 1 6 8 9 14 16

(+) Ignition: Green/Black, pin 14 HS CAN Low: VESCM - Driver side under dashboard Orange/Brown, pin 14 Steering Column Module (behind steering column trim) HS CAN 1 Low: Tan: 1 2

[5] Diode 1A HS CAN 1 High: Tan/Black: 2 8 FT CAN Low: Orange/Brown: 3

FT CAN High: Orange/Green: 4 5 MAIN (5A) (+) (5A) MAIN

(-) Hazards Output: Lt.Green/Black: 1

(-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-)

(+) 12V: (+) Starter / Brake Activation Output: White: 7 30

Red/Yellow, 42 25 1 (+) (30A) START & ACC (-) 4

pin 42 (+) Ignition Output: Violet/Black: 8 20 22

MAIN (5A) (+) (5A) MAIN

(-) FLEX RLY (20A) (+) (20A) RLY FLEX (-)

(+) Siren Output: Brown/Red: 11 20

(-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) Hood Pin (+) (20A) IGN 28 Siren

(-) Hood Input: Gray: 21 4 29 12 (-) Hazards: Brown/Red, pin 7 DS4+ DS4 (+) 12V Input: Red: 6 & 12 Proper Fuse Key Wrap: Lt.Green/Red: 7 Positioning 2 [5] Diode 1A

Key Wrap: Lt. Green: 8 12

(+) Brake: Black/Red, pin 17 Key Wrap: Lt. Green/White: 9 52 41 24 11 DS4 Brown VESCM connector C (-) Ground: Black: 10 10

Slide DS4+ to open

It is important to check that the fuses are positioned correctly.

DS4+ VW10 18 © 2017-11-02 Directed. All rights reserved. Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Audi Q3 2015-2017 HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A Starter Red/Black 6 (+) Steering column module behind steering column trim. Black 16 B Ignition Green/Black 14 (+) Steering column module behind steering column trim. Black 16 B Orange/Green or FT CAN High 4 Data Steering column module behind steering column trim. Black 16 B Lt.Green FT CAN Low Orange/Brown 3 Data Steering column module behind steering column trim. Black 16 B 12V Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 C Hazards Brown/Red 7 (-) VESCM connector C, under drivers dash. Brown 52 C Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 C

19 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Type 6 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).

(+) Starter: Pin 6

(+)12V 86 87 85 Steering Column Module 1 6 8 87a HS CAN High: 9 14 16 Fuse 5A Orange/Black, pin 6 (behind steering column trim) (+) Keysense: 30 Green or 1 8 Diagnostic Green/Blue, pin 16 9 16 Connector OBDII

[5] Diode 1A (+) Ignition: HS CAN Low: Red/Green or Orange/Brown, pin 14 Violet/Yellow, pin 5 Ignition Switch Plug (at Key Port)

HS CAN 1 Low: Tan: 1

HS CAN 1 High: Tan/Black: 2 2

[5] (+) Brake: Black/Red, pin 17 8 FT CAN Low: Orange/Brown: 3

(+) 12V: [5] Diode 1A 4 FT CAN High: Orange/Green: 4 5 Red/Yellow, 42 25 1

pin 42 (+) (5A) MAIN (-) Key Release Output: Blue/White: 2

(+) Starter / Brake Activation Output: White: 7 (+) (15A) LIGHT PK RLY3 (-) 30

(+) Ignition Output: Violet/Black: 8 (+) (30A) START & ACC (-) 4 28 5 20

29 12 22 MAIN (5A) (+) (5A) MAIN

FT CAN High: (+) (20A) RLY FLEX (-)

Orange/Green, pin 15 (+) Siren Output: Brown/Red: 11 20

(-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) Hood Pin (+) (20A) IGN Siren FT CAN Low: (-) Hood Input: Gray: 21 4 Orange/Brown, pin 16 DS4+ DS4 Parking Light Interrupt (conn. side): Blue/White: 1 (+) Parking Light Output: Blue/Red: 2 Proper Fuse

Parking Light Interrupt (vehicle side): Blue: 3 2 52 41 24 11 Positioning (+) 12V Input: Red: 6 & 12 Brown VESCM connector C Key Wrap: Lt.Green/Red: 7 12 Key Wrap: Lt. Green: 8 Key Wrap: Lt. Green/White: 9 DS4 (-) Ground: Black: 10

C B A Parking Lights Interrupt: Red/White or Red/Black, pin 8 CUT 10

Slide DS4+ 10 9 8 7 6 Headlight Switch to open (black conn. at light switch) 5 4 3 2 1

(+) Parking Lights: Gray/Yellow It is important to check that the or Gray/Green, pin 3 fuses are positioned correctly.

VESCM - Driver side under dashboard

DS4+ VW10 20 © 2017-11-02 Directed. All rights reserved. Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Volkswagen Passat CC 2011-2016 Gray/Yellow or Gray/ Parking light 3 (+) Headlight switch. Black 10 A Green Parking light Interrupt Red/White or Red/Black 8 Cut Headlight switch. Black 10 A Red/Brown or Red/Gray Starter 6 (+) Ignition switch port. Black 16 B or Red/Yellow Red/Green or Violet/ Ignition 5 (+) Ignition switch port. Black 16 B Yellow Keysense Green or Green/Blue 16 (+) Ignition switch port. Black 16 B HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C 12V Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D FT CAN High Orange/Green 15 Data VESCM connector C, under drivers dash. Brown 52 D FT CAN Low Orange/Brown 16 Data VESCM connector C, under drivers dash. Brown 52 D Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D

21 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Type 7 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).

C B A

FT CAN Low: Orange/Brown, pin 15

FT CAN High: Orange/Green, pin 14 HS CAN High: Orange/Black, pin 6 (+) Starter: Red/Black or Red/Brown, pin 18 Diagnostic 1 8 Steering column Connector module 9 16 1 20 OBDII 10 17 (behind steering column trim) HS CAN Low: Orange/Brown, pin 14 (+) Ignition: Black, pin 17 VESCM - Driver side under dashboard [5] Diode 1A

HS CAN 1 Low: Tan: 1

(+) Brake: Black/Red, pin 17 HS CAN 1 High: Tan/Black: 2 2 8 FT CAN Low: Orange/Brown: 3

(+) 12V: 42 25 1 [5] Diode 1A

4 Red/Yellow, pin 42 5

FT CAN High: Orange/Green: 4 MAIN (5A) (+) (5A) MAIN

(+) Starter / Brake Activation Output: White: 7

(-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-)

28 30

29 12 (+) Ignition Output: Violet/Black: 8 (+) (30A) START & ACC (-)

5 20

22 MAIN (5A) (+) (5A) MAIN

(+) Siren Output: Brown/Red: 11 (+) (20A) RLY FLEX (-)

(-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) Hood Pin (+) (20A) IGN Siren (-) Hood Input: Gray: 21 DS4+ DS4 4 Parking Light Interrupt (conn. side): Blue/White: 1 52 41 24 11 (+) Parking Light Output: Blue/Red: 2 Proper Fuse Brown VESCM connector C Parking Light Interrupt (vehicle side): Blue: 3 Positioning 2 (+) 12V Input: Red: 6 & 12

Key Wrap: Lt.Green/Red: 7 12 Key Wrap: Lt. Green: 8 Key Wrap: Lt. Green/White: 9 DS4 (-) Ground: Black: 10 Parking Lights Interrupt: Red/White, pin 8

CUT 10

Slide 10 9 8 7 6 Headlight switch DS4+ (black conn. at to open 5 4 3 2 1 light switch)

(+) Parking Lights: White/Black, pin 1 It is important to check that the fuses are positioned correctly.

DS4+ VW10 22 © 2017-11-02 Directed. All rights reserved. Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Volkswagen Jetta SportWagen 2010 Parking Light White/Black 1 (+) Headlight Switch. Black 10 A Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 B HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 B Starter Red/Black or Red/Brown 18 (+) Steering column module. Black 16 C Ignition Black 17 (+) Steering column module. Black 16 C FT CAN High Orange/Green 14 Data Steering column module. Black 16 C FT CAN Low Orange/Brown 15 Data Steering column module. Black 16 C 12V Red /Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D

23 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Type 8 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).

VESCM (+) Ignition: Black or Black/Green, pin 11 (under drivers dash or below glove box) HS CAN High: Orange/Black, pin 6

(+) Starter: Red/Black or Black, pin 1 Diagnostic 1 8 1 2 3 4 5 6 Connector G plug OBDII 9 16 at VESCM 7 8 9 10 1112 (under drivers dash HS CAN Low: Orange/Brown, pin 14 or below glove box)

FT CAN Low: E F G H Orange/ Brown,pin 7 (-) Hazards: Brown/Red or Blue/Red, pin 9

FT CAN High: Orange/Green, pin 8 HS CAN Low: Tan: 1

HS CAN High: Tan/Black: 2 2

FT CAN Low: Orange/Brown: 3 8

FT CAN High: Orange/Green: 4

4 5 MAIN (5A) (+) (5A) MAIN

(-) Hazards Output: Lt. Green/Black: 1

(-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-)

(+) Starter Output: White: 7 30

(-) ACC & START (30A) (+) (30A) START & ACC (-) 4

5 20

(+) Ignition Output: Violet/Black: 8 22

MAIN (5A) (+) (5A) MAIN

(-) FLEX RLY (20A) (+) (20A) RLY FLEX (-)

(+) Siren Output: Brown/Red: 11 20 (-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-)

Hood Pin (+) (20A) IGN Siren (-) Hood Input: Gray: 21 DS4+ DS4 4

VESCM Connector L (+) 12V Input: Red: 6 & 12 Proper Fuse

(under drivers dash or behind glove box) 2 Key Wrap: Lt.Green/Red: 7 Positioning 2 10 6 4 2 Key Wrap: Lt. Green: 8 12 3 1 Key Wrap: Lt. Green/White: 9 DS4 2 (-) Ground: Black: 10

(+)12V: Pin 1 10

Slide DS4+ to open

It is important to check that the fuses are positioned correctly.

DS4+ VW10 24 © 2017-11-02 Directed. All rights reserved. Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Audi A3 2004-2008 12V Red/Black or Black 1 (+) VESCM connector L, under drivers dash. Black 2 A Starter Red/Black or Black 1 (+) VESCM connector G, under drivers dash. Black 12 B Ignition Black or Black/Green 11 (+) VESCM connector G, under drivers dash. Black 12 B FT CAN High Orange/Green 8 Data VESCM connector G, under drivers dash. Black 12 B FT CAN Low Orange/Brown 7 Data VESCM connector G, under drivers dash. Black 12 B Hazards Brown/Red 9 (-) VESCM connector G, under drivers dash. Black 15 B HS CAN High Orange/Black 6 Data OBDII. Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Black 16 C Audi R8 2008-2009 12V Black/Blue 1 (+) VESCM connector L, below glove box. Black 2 D Starter Red/Black or Black 1 (+) VESCM connector G, below glove box. Black 12 E Ignition Black/Violet 11 (+) VESCM connector G, below glove box. Black 12 E FT CAN High Orange/Green 8 Data VESCM connector G, below glove box. Black 12 E FT CAN Low Orange/Brown 7 Data VESCM connector G, below glove box. Black 12 E Hazards Blue/Red 9 (-) VESCM connector G, below glove box. Black 15 E HS CAN High Orange/Black 6 Data OBDII. Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Black 16 C Audi TT 2006-2009 12V Red 1 (+) VESCM connector L, under drivers dash. Black 2 A Starter Red/Black or Black 1 (+) VESCM connector G, under drivers dash. Black 12 B Ignition Black/White 11 (+) VESCM connector G, under drivers dash. Black 12 B FT CAN High Orange/Green 8 Data VESCM connector G, under drivers dash. Black 12 B FT CAN Low Orange/Brown 7 Data VESCM connector G, under drivers dash. Black 12 B Hazards Brown/Red 9 (-) VESCM connector G, under drivers dash. Black 15 B HS CAN High Orange/Black 6 Data OBDII. Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Black 16 C

25 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Type 9 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).

VESCM (under drivers dash or below glove box) (+) Ignition: Black or Black/Green, pin 11 HS CAN High: Orange/Black, pin 6 Diagnostic (+) Starter: Pin 1 1 8 1 2 3 4 5 6 Connector G plug OBDII 9 16 at VESCM 7 8 9 10 1112 (under drivers dash HS CAN Low: Orange/Brown, pin 14 or below glove box)

FT CAN Low: E F G H Orange/ Brown,pin 7

FT CAN High: Orange/Green, pin 8 HS CAN Low: Tan: 1

HS CAN High: Tan/Black: 2 2

FT CAN Low: Orange/Brown: 3 8

FT CAN High: Orange/Green: 4 5 MAIN (5A) (+) (5A) MAIN

(+) Starter Output: White: 7

(-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-) 30

(+) Ignition Output: Violet/Black: 8 (+) (30A) START & ACC (-) 4 5 20

MAIN (5A) (+) (5A) MAIN

(-) FLEX RLY (20A) (+) (20A) RLY FLEX (-)

(+) Siren Output: Brown/Red: 11 20 (-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-)

Hood Pin (+) (20A) IGN Siren (-) Hood Input: Gray: 21 DS4+ DS4 4 Parking Light Interrupt (conn. side): Blue/White: 1 VESCM Connector L (+) Parking Light Output: Blue/Red: 2 Proper Fuse (under drivers dash or behind glove box) Parking Light Interrupt (vehicle side): Blue: 3 Positioning 2 2 10 6 4 2 (+) 12V Input: Red: 6 & 12 12 3 1 Key Wrap: Lt.Green/Red: 7 Key Wrap: Lt. Green: 8 Key Wrap: Lt. Green/White: 9 DS4 2 (-) Ground: Black: 10

1 Parking Lights Interrupt: Red/White, pin 8 CUT

(+)12V: Pin 1 10

Slide 10 9 8 7 6 Headlight switch DS4+ (black conn. at to open 5 4 3 2 1 light switch)

It is important to check that the (+) Parking Lights: fuses are positioned correctly. Gray/Yellow, pin 3

DS4+ VW10 26 © 2017-11-02 Directed. All rights reserved. Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Volkswagen EOS 2006-2009 12V Red/Black or Black 1 (+) VESCM connector L, under drivers dash. Black 2 A Parking Light Gray/Yellow 3 (+) Headlight switch. Black 10 B Parking Light Interrupt Red/White 8 Cut Headlight switch. Black 10 B Starter Red/Black 1 (+) VESCM connector G, under drivers dash. Black 12 C Ignition Black or Black/Green 11 (+) VESCM connector G, under drivers dash. Black 12 C FT CAN High Orange/Green 8 Data VESCM connector G, under drivers dash. Black 12 C FT CAN Low Orange/Brown 7 Data VESCM connector G, under drivers dash. Black 12 C HS CAN High Orange/Black 6 Data OBDII. Black 16 D HS CAN Low Orange/Brown 14 Data OBDII. Black 16 D Volksawgen Golf 2006-2009 12V Red/Black or Black 1 (+) VESCM connector L, under drivers dash. Black 2 A Parking Light Gray/Yellow 3 (+) Headlight switch. Black 10 B Parking Light Interrupt Red/White 8 Cut Headlight switch. Black 10 B Starter Red/Black or Red/Brown 1 (+) VESCM connector G, under drivers dash. Black 12 C Ignition Black or Black/Green 11 (+) VESCM connector G, under drivers dash. Black 12 C FT CAN High Orange/Green 8 Data VESCM connector G, under drivers dash. Black 12 C FT CAN Low Orange/Brown 7 Data VESCM connector G, under drivers dash. Black 12 C HS CAN High Orange/Black 6 Data OBDII. Black 16 D HS CAN Low Orange/Brown 14 Data OBDII. Black 16 D Volkswagen GTI 2006-2009 12V Red/Black or Black 1 (+) VESCM connector L, under drivers dash. Black 2 A Parking Light Gray/Yellow 3 (+) Headlight switch. Black 10 B Parking Light Interrupt Red/White 8 Cut Headlight switch. Black 10 B Starter Red/Black or Red/Brown 1 (+) VESCM connector G, under drivers dash. Black 12 C Ignition Black or Black/Green 11 (+) VESCM connector G, under drivers dash. Black 12 C FT CAN High Orange/Green 8 Data VESCM connector G, under drivers dash. Black 12 C FT CAN Low Orange/Brown 7 Data VESCM connector G, under drivers dash. Black 12 C HS CAN High Orange/Black 6 Data OBDII. Black 16 D HS CAN Low Orange/Brown 14 Data OBDII. Black 16 D

27 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Volkswagen Jetta 2006-2010 12V Red/Black or Red/Yellow 1 (+) VESCM connector L, under drivers dash. Black 2 A Parking Light Gray/Yellow 3 (+) Headlight switch. Black 10 B Parking Light Interrupt Red/White 8 Cut Headlight switch. Black 10 B Starter Red/Black or Red/Brown 1 (+) VESCM connector G, under drivers dash. Black 12 C Ignition Black or Black/Green 11 (+) VESCM connector G, under drivers dash. Black 12 C FT CAN High Orange/Green 8 Data VESCM connector G, under drivers dash. Black 12 C FT CAN Low Orange/Brown 7 Data VESCM connector G, under drivers dash. Black 12 C HS CAN High Orange/Black 6 Data OBDII. Black 16 D HS CAN Low Orange/Brown 14 Data OBDII. Black 16 D Volkswagen Jetta SportWagen 2009 12V Red/Black 1 (+) VESCM connector L, under drivers dash. Black 2 A Parking Light Gray/Yellow 3 (+) Headlight switch. Black 10 B Parking Light Interrupt Red/White 8 Cut Headlight switch. Black 10 B Starter Red/Black or Red/Brown 1 (+) VESCM connector G, under drivers dash. Black 12 C Ignition Black 11 (+) VESCM connector G, under drivers dash. Black 12 C FT CAN High Orange/Green 8 Data VESCM connector G, under drivers dash. Black 12 C FT CAN Low Orange/Brown 7 Data VESCM connector G, under drivers dash. Black 12 C HS CAN High Orange/Black 6 Data OBDII. Black 16 D HS CAN Low Orange/Brown 14 Data OBDII. Black 16 D Volkswagen Rabbit 2006-2009 12V Red/Black or Red/Yellow 1 (+) VESCM connector L, under drivers dash. Black 2 A Parking Light Gray/Yellow 3 (+) Headlight switch. Black 10 B Parking Light Interrupt Red/White 8 Cut Headlight switch. Black 10 B Starter Red/Black or Red/Brown 1 (+) VESCM connector G, under drivers dash. Black 12 C Ignition Black or Black/Green 11 (+) VESCM connector G, under drivers dash. Black 12 C FT CAN High Orange/Green 8 Data VESCM connector G, under drivers dash. Black 12 C FT CAN Low Orange/Brown 7 Data VESCM connector G, under drivers dash. Black 12 C HS CAN High Orange/Black 6 Data OBDII. Black 16 D HS CAN Low Orange/Brown 14 Data OBDII. Black 16 D

28 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Type 10 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).

VESCM Connector L (under drivers dash or behind glove box) 2 2 10 6 4 2

3 1 1 (+)12V: Red/White, pin 1 G plug at VESCM (under drivers dash) (+) Ignition: Red/Violet, pin 11 HS CAN High: VESCM (under drivers dash) 1 2 3 4 5 6 Orange/Black, pin 6 (+) Starter: (+) Brake: Red/Gray or Black/Red, pin 2 Red/Violet, pin 1 7 8 9 10 1112 1 8 Diagnostic

9 16 Connector OBDII E plug FT CAN Low: at VESCM 1 2 3 4 5 6 7 8 Orange/ Brown,pin 7 (under HS CAN Low: 9 10 11 12131415 16 Orange/Brown, pin 14 drivers dash) FT CAN High:

Fuse 5A [5] Diode 1A Orange/Green, E F G H pin 8 HS CAN Low: Tan: 1 86 87 85 HS CAN High: Tan/Black: 2 2 87a 8 30 FT CAN Low: Orange/Brown: 3

4 FT CAN High: Orange/Green: 4 5

Ignition Switch Port (-) Key Release Output: Blue/White: 2 (+) (5A) MAIN

(black conn. at keyport) (+) Starter / Brake Activcation Output: White: 7 (+) (15A) LIGHT PK RLY3 (-) 30

(-) ACC & START (30A) (+) (30A) START & ACC (-) 4

(+) Ignition Output: Violet/Black: 8 5 20

22 MAIN (5A) (+) (5A) MAIN

(+) Siren Output: Brown/Red: 11 (+) (20A) RLY FLEX (-)

Siren 20

(-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) Hood Pin (+) (20A) IGN (-) Hood Input: Gray: 21 DS4+ DS4 4 Parking Light Interrupt (conn. side): Blue/White: 1 Ignition Switch Plug (+) Parking Light Output: Blue/Red: 2 Proper Fuse

(at Key Port) 2 Parking Light Interrupt (vehicle side): Blue: 3 Positioning (+) 12V Interrupt: Green/Red, pin 3 (+) 12V Input: Red: 6 & 12

CUT Key Wrap: Lt.Green/Red: 7 12 1 2 3 4 5 6 7 8 Key Wrap: Lt. Green: 8 9 10 11 12 13 14 15 16 Key Wrap: Lt. Green/White: 9 DS4 Keysense: Green, pin 16 (-) Ground: Black: 10

Parking Lights Interrupt: Red/White or Red/Black, pin 8 Fuse 5A 86 87 85

87a CUT 10 30 Slide DS4+ 10 9 8 7 6 Headlight Switch to open (black conn. at light switch) 5 4 3 2 1 It is important to check that the (+) Parking Lights: Gray/Yellow, pin 3 fuses are positioned correctly.

DS4+ VW10 29 © 2017-11-02 Directed. All rights reserved. Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Volkswagen Passat 2006-2010 12V Red/White 1 (+) VESCM connector L, under drivers dash. Black 2 A Parking Light Gray/Yellow 3 (+) Headlight switch. Black 10 B Parking Light Interrupt Red/White or Red/Black 8 Cut Headlight switch. Black 10 B Starter Red/Gray or Red/Violet 1 (+) VESCM connector G, under drivers dash. Black 12 C Ignition Red/Violet 11 (+) VESCM connector G, under drivers dash. Black 12 C FT CAN High Orange/Green 8 Data VESCM connector G, under drivers dash. Black 12 C FT CAN Low Orange/Brown 7 Data VESCM connector G, under drivers dash. Black 12 C Keysense Green 16 (+) Keyport switch. Black 16 D 12V Interrupt Green/Red 3 (+) Keyport switch. Black 16 D Brake Black/Red 2 (+) VESCM connector E, under drivers dash. Black 16 E HS CAN High Orange/Black 6 Data OBDII. Black 16 F HS CAN Low Orange/Brown 14 Data OBDII. Black 16 F Volkswagen Passat CC 2009-2010 12V Red/White 1 (+) VESCM connector L, under drivers dash. Black 2 A Parking Light Gray/Yellow 3 (+) Headlight switch. Black 10 B Parking Light Interrupt Red/White or Red/Black 8 Cut Headlight switch. Black 10 B Starter Red/Gray or Red/Violet 1 (+) VESCM connector G, under drivers dash. Black 12 C Ignition Red/Violet 11 (+) VESCM connector G, under drivers dash. Black 12 C FT CAN High Orange/Green 8 Data VESCM connector G, under drivers dash. Black 12 C FT CAN Low Orange/Brown 7 Data VESCM connector G, under drivers dash. Black 12 C Keysense Green 16 (+) Keyport switch. Black 16 D 12V Interrupt Green/Red 3 (+) Keyport switch. Black 16 D Brake Black/Red 2 (+) VESCM connector E, under drivers dash. Black 16 E HS CAN High Orange/Black 6 Data OBDII. Black 16 F HS CAN Low Orange/Brown 14 Data OBDII. Black 16 F

30 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Type 11 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).

VESCM - Driver side, under dashboard White VESCM Connector B (under drivers kick) 16 3 7 73 HS CAN High: Orange/Black, pin 6

1 8 Diagnostic

9 16 Connector OBDII FT CAN Low: Orange/Brown, pin 21 HS CAN Low: Orange/Brown, pin 14 FT CAN High: Orange/Green, pin 20

1 17 63 Connector Connector HS CAN Low: Tan: 1 A B HS CAN High: Tan/Black: 2 2

FT CAN Low: Orange/Brown: 3 8

FT CAN High: Orange/Green: 4

5 5 5 5 5 4 5 5 5 5 5 5 5 5 5 5 5 5 (MUX) Lock/Unlock Output: Violet/Brown: 6 5

MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN (+) (5A) MAIN (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN (+) (5A) MAIN

15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 (-) Trunk Release Output: Red/White: 4 15

(-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-) (-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (-) RLY3 PK LIGHT (15A) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-) (+) (15A) LIGHT PK RLY3 (-)

30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 (+) Starter/Brake Activation Output: White: 7 30

16 (-) ACC & START (30A) (+) (30A) START & ACC (-) (-) ACC & START (30A) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (-) ACC & START (30A) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (-) ACC & START (30A) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-) (+) (30A) START & ACC (-)

37 73 (+) (30A) START & ACC (-)

5 5 5 5 5 5

20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20

(+) Ignition Output: Violet/Black: 8 20

MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN MAIN (5A) (+) (5A) MAIN

(-) FLEX RLY (20A) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (-) FLEX RLY (20A) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (-) FLEX RLY (20A) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (-) FLEX RLY (20A) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-) (+) (20A) RLY FLEX (-)

15 15 15 15 15 15 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 (+) 12V: 20

(+) Siren Output: Brown/Red: 11

(-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) (-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) (-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) (-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) (-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) (-) RLY3/PK LIGHT(15A) (+) LIGHT(15A) RLY3/PK (-) IGN (20A) (+) (20A) IGN IGN (20A) (+) (20A) IGN (+) (20A) IGN (+) (20A) IGN (+) (20A) IGN (+) (20A) IGN IGN (20A) (+) (20A) IGN IGN (20A) (+) (20A) IGN (+) (20A) IGN (+) (20A) IGN (+) (20A) IGN (+) (20A) IGN IGN (20A) (+) (20A) IGN (+) (20A) IGN (+) (20A) IGN IGN (20A) (+) (20A) IGN (+) (20A) IGN Red/White (+) (20A) IGN Hood Pin (MUX) Doorlock: or Red/Yellow, Siren (-) Hood Input: Gray: 21 4 Blue/Red,pin 24 pin 68 DS4+ DS4 Parking Light Interrupt (conn. side): Blue/White: 1 (-) Trunk (+) Parking Light Output: Blue/Red: 2 Release: [5] Diode 1A Proper Fuse

(+) Brake: 2 Violet, pin 23 Parking Light Interrupt (vehicle side): Blue: 3 Positioning Black/Red, pin 39 (+) Accessory Output: White: 5 & 11

(+) 12V Input: Red: 6 & 12 12 1 17 63 Key Wrap: Lt.Green/Red: 7 Black VESCM connector A Key Wrap: Lt. Green: 8 DS4 (under drivers kick) [5] Diode 1A Key Wrap: Lt. Green/White: 9 (-) Ground: Black: 10

Parking Lights Interrupt: Red/Yellow, pin 8

(+) Starter: (+) Ignition: CUT 10 Red/Black, pin 4 Black/Violet, pin 8 Slide DS4+ 10 9 8 7 6 to open Ignition Switch 10 9 8 7 6 Headlight Switch (black conn. at 2 (black conn. at light switch) 5 4 3 2 1 5 4 3 1 ignition switch) It is important to check that the (+) Accessory: Black/Red, pin 3 fuses are positioned correctly. (+) Parking Lights: White/Black, pin 1

DS4+ VW10 31 © 2017-11-02 Directed. All rights reserved. Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information.

Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Volkswagen Jetta 2015-2017 Starter Red/Black 4 (+) Ignition switch. Black 10 A Ignition Black/Violet 8 (+) Ignition switch. Black 10 A Accessory Black/Red 3 (+) Ignition switch. Black 10 A Parking Light White/Black 1 (+) Headlight switch. Black 10 B Parking Light Interrupt Red/Yellow 8 Cut Headlight switch. Black 10 B HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C FT CAN High Orange/Green 20 Data VESCM connector B, under drivers dash. White 73 D FT CAN Low Orange/Brown 21 Data VESCM connector B, under drivers dash. White 73 D 12V Red/White or Red/Yellow 68 (+) VESCM connector A, under drivers dash. Black 73 E Brake Black/Red 39 (+) VESCM connector A, under drivers dash. Black 73 E Doorlocks Blue/Red 24 MUX VESCM connector A, under drivers dash. Black 73 E Trunk Release Violet 23 (-) VESCM connector A, under drivers dash. Black 73 E

32 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Immobilizer interface For vehicles with Keyless Entry you must remove battery from OEM key (the OEM remote may differ from the models shown in the illustrations). Method 1: Key Wrap 2 8 4 4 22 4 NO Relay 2: Lt.Green/Red: 7 2 12 OEM COM Relay 2: Lt.Green 8 Immobilizer Receiver 4-6 loops *

4-6 loops

- Make 4-6 loops and place them as close to the front of key port (OEM Immobilizer Receiver) as possible. - Make 4-6 loops and place them around the front of the plastic body of the vehicle’s coded key as shown above. - Test and secure mounted loops before reassembling the vehicle. * When possible use valet key for key wrap, if blade key is used, battery must be removed. Method 2: Immobilizer interface with 556U (Regular Key) 556U or 556UW is sold SEPARATELY. 2 8 4 4 22 4

NO Relay 2: Lt.Green/Red: 7 2 12

COM Relay 2: Lt.Green 8 Move the 556U loop as close to the front of ignition cylinder (OEM Immobilizer Receiver) as possible. Test and secure mounted loop (-) Ground: Black, pin 1 before reassembling the vehicle. (+) 12V (+) 12V: Red, pin 2 N/A : Violet, pin 3 (-) GWR: Blue, pin4 N/A: Green, pin 5 OEM N/A:Brown , pin 6 Immobilizer Receiver

IMPORTANT!: Not all OEM remotes can be inserted in 556U 8 4 because of their size. Make sure the key will fit, otherwise it is recommended to use a different method.

NO Relay 2: Lt.Green/Red: 7 4

COM Relay 2: Lt.Green: 8 2 12

NC Relay 2: Lt.Green/White: 9

Remove battery 4-6 loops from OEM OEM Remote Control Immobilizer Receiver

Immobilizer ECU

- Make 4-6 loops and place them around the front of the plastic body of the vehicle's coded key as shown above. - Make connections to the OEM Immobilizer receiver as shown above. - Test and secure mounted loops before reassembling the vehicle. * When possible use valet key for key wrap, if blade key is used, battery must be removed.

Important! Before connecting the DS4+, it is important to ensure that the proper feature and function programming is selected using the configuration wizard. Visit www.directechs.com to use the latest version of the online tool.

Flashing a module using your computer: 1. Disconnect the main module from any (+) 12V power source, then connect it to your computer using the XKLoader2. 2. Go to www.directechs.com using Internet Explorer; the configuration wizard will be displayed automatically. 3. Follow the instructions in the pop up window that will be displayed when the module is detected.

Flashing a module using your smartphone or tablet: 1. Disconnect the main module from any (+) 12V power source, then connect it to the XKLoader3. 2. Launch the Directechs Mobile app on your smartphone or tablet. 3. Select FLASH YOUR MODULE and follow the on-screen instructions.

When the flashing operation is successful, you can proceed with the instructions below.

Additional connections required for vehicles equipped with a manual transmission (if not supported by firmware)

Connection Description (-) E-Brake Status Input Must be connected to a working emergency brake in the vehicle. Although most vehicles have simple (Black/White, pin 17) (-) trigger emergency brake circuits note some vehicles do not and may require unique integration methodologies. (-) Door Trigger Input Must be connected to a working door trigger in the vehicle, which monitors all doors. The unit must monitor (Green, pin 20) OR the door pins to allow the Ready Mode process to be enabled. (+) Door Input (Violet, pin Note: Some vehicles may require unique integration methodologies for this circuit. 13) (AC) Tachometer Input Must be connected to a working tachometer signal in the vehicle (fuel injector, ignition coil, true tach, etc.) (Violet/White, pin 22) and learned successfully to the DS4+.

Note: Refer to www.directechs.com for more information.

RF Systems An RF System consists of one or multiple remotes, a Control Center (antenna), and an antenna cable – various combinations exist. An RF System allows the vehicle owner to control the system with enhanced range. Two-way models are available. Please follow the instructions included with the kit for appropriate installation and programming information.

8504D Combo Sensor The 8504D Combo Sensor must be paired to the device before it can be used. To enter pairing, turn the vehicle ignition to the ON position, then press and hold the programming button on the Control Center (antenna) until the LED starts flashing. Once pairing mode has been entered, your Combo Sensor is ready to use.

Your Combo Sensor is preset for the majority of applications, however it can be adjusted using the DirectLink application, as well as a compatible LED or LCD remote. Please refer to the instructions included with your sensor for more information on how to make adjustments.

35 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. When used in conjunction with SmartStart To enable D2D communication between the DS4+ and the SmartStart one of the following actions must be executed: • SmartStart with Loops – The brown loop must be cut. • SmartStart with Pigtails – The gray wire must be connected to a ground source.

Loops Pigtails

DO NOT connect the SmartStart 2-pin power harness when using the DS4+. Power and ground will be provided by the D2D connector on main module. Refer to the SmartStart documentation for further details.

D2D port configuration The system will automatically configure the D2D ports based on your selections in the module programming. The white D2D port is reserved for SmartStart. To ensure proper functionality with SmartStart, it is important that it is selected in the system programming of the DirectLink application or via the online web tool.

Note: Both black D2D ports are reserved for the Control Center (antenna) and 8504D Combo Sensor.

To connect the module: Please ensure that the vehicle is in a safe location and cannot move forward during 1 programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. Connect all but the 12-pin harness 2 Connect all the harnesses to the DS4+, EXCEPT the 12-pin main power harness.

Must be connected LAST Connect the 12-pin main power harness, and wait until the LED turns ON solid red. & 3 Solid F F

Press Unlock on the OEM fob then insert key into key switch and turn ON. The LED flashes O N IG & 4 START Flashes green. green F F

O N IG F

START F O N 5 Wait for the LED to turn solid green for 3 seconds then OFF. Solid & OffIG START

xF 3 secs F

O N IG START F F

O N Turn vehicle ignition OFF once the module is successfully programmed. IG 6 START F F

Pair O N Pair remotes (if applicable). For information on how to pair a specific remote, please remotes* IG 7 refer to its corresponding owner documentation, which can be found inside the product START packaging of the complete system or on www.directechs.com.*

By default, the tachometer is preprogrammed for the vehicle. For instructions on how to Initialize 8 program tach, see page 41. tachometer

* Your aftermarket remote may differ from the model shown in the illustrations.

You have successfully completed the module programming sequence.

37 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module programming

LED Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black Module has no power. Off wires. If 12 Volt is present, the module may be defective. Waiting to begin the programming Ensure the correct programming procedure is being followed. Solid red sequence.

Reset the module and complete the programming again. If the issue persists, please contact Flashes red & Initialization failed. green Technical Support. (If compatible) when the RXT mode is not desired or convenience features are needed, please Transponder functions were skipped. Solid orange reset and reprogram the module. All required CAN networks has been Normal operation. Flashes green detected.

1 of 2 CAN networks has been detected. Normal operation. Flashes orange

Please follow the steps indicated in "Module programming" on page 37 to complete the Flashes orange Key2GO initiated. slowly Key2GO programming.

Module was successfully programmed Solid green x Normal operation. 3 secs with all functions. Module was successfully Solid orange x programmed without transponder Normal operation. 3 secs functions. Module programming – Error codes

LED Description Troubleshooting Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus CAN2 not detected. by turning the ignition on and try again. If your installation does not require this connection, skip Flashes red x 1 this step by pressing the programming button 5 times. Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try J1850 not detected. Flashes red x 1 again. Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the CAN1 not detected. ignition on and try again. If your installation does not require this connection, skip this step by Flashes red x 2 pressing the programming button 5 times. Check the bypass line connection. If more than one wire is used, make sure they are not inverted. Bypass data not detected. Flashes red x 3 Ensure the vehicle still operates correctly using the factory key. The bypass calculation failed. Reset the module and try again. If the condition persists, please Bypass processing error. Flashes red x 4 contact Technical Support. The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams, ISO 1 not detected. Flashes red x 5 fuse selection & vehicle wiring reference charts)" on page 8 to check the connections. The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams, ISO 2 not detected. Flashes red x 6 fuse selection & vehicle wiring reference charts)" on page 8 to check the connections. The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to MUX not detected. "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 8 to Flashes red x 7 check the connections. External module synchronization

LED Description Troubleshooting

(Flashes red, red, OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. then orange) x 10

LED Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence. Flashes green received.

Flashes red & Ignition ON command received. The module has received the Ignition ON command and is processing the remote start sequence. orange

Flashes green Start ON command received. The module has received the Start ON command and is processing the remote start sequence. quickly

PTS shutdown error. The PTS output from the module was not activated due to safety protection. Flashes red x 10 Verify the CAN1 and CAN2 connections. Refer to "Installation (wiring diagrams, fuse selection & CAN bus incorrectly detected. Flashes red x 21 vehicle wiring reference charts)" on page 8 to check the connections.

Commands

LED Description Troubleshooting

LOCK command received. Flashes orange x 1

UNLOCK command received. Flashes orange x 2

TRUNK command received. Flashes orange x 3 If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or D2D. AUX1 command received. Flashes orange x 4

AUX2 command received. Flashes orange x 5

AUX3 command received. Flashes orange x 6

Shutdown codes

LED Description Troubleshooting

Takeover successful. Normal operation. Flashes green x 1 No UNLOCK command was received prior to opening the door, or the 45 second timer expired Runsafe was not disabled. Flashes red x 1 in takeover mode.

Brake was not detected. The brakes were not detected, which prevents the system from shutting down the vehicle. Flashes red x 2

Smart key was not detected. The smart key was not detected, which prevents the system from shutting down the vehicle. Flashes red x 3

Speed was detected. The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4

Analog error codes

LED Description Troubleshooting

Flashes red, green DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. & orange

39 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Soft reset A module reset will only erase the steps performed in "Module programming" on page 37. The firmware and settings flashed to the module will not be affected.

Connect all but the If required for your installation, connect all the harnesses to the DS4+, EXCEPT the 12-pin 12-pin harness 1 main power harness. Press and hold the programming button, then connect the 12-pin harness to the module.

Wait 3 seconds until the LED turns ON solid orange then release the programming button. & & 2 The LED turns ON solid red. Solid Release Solid

Hard reset Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings may need to be reconfigured. Connect your module to a computer and use the web configuration tool to edit its programmable features.

After 3 seconds the LED turns ON solid orange. Keep holding the programming button until & & 2 the LED flashes red, then orange slowly. Solid Hold Flashes

3 Release the programming button. The LED turns ON solid red. & Release Solid

40 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Learning the Tach (not needed with Virtual Tach) Tach comes preprogrammed, therefore learning is not required; however, it can be readjusted with the following operations: 1. Start the vehicle using the key. 2. Within 5 seconds, press and hold the Control Center* (antenna) or the main module programming button, until the LED on the Control Center (antenna) or the main module turns ON solid. 3. Release the button. Tachometer value is now stored in memory. If the LED does not turn ON solid, find an alternate tach source.

* If the Control Center (antenna) was not included in your kit, the tach can be programmed using the programming button directly on the main module.

Note: When the tachometer is programmed, the main module automatically enters the Tachometer engine checking mode.

Initializing Virtual Tach (not needed with hardwired or data tach applications) To program Virtual Tach: 1. After the install is complete, remote start the engine. The programming operation may require 3 cranks of the starter before the engine starts and runs. Do not turn off the remote start if this happens, it is a normal programming operation. 2. Once the engine begins running, let it run for at least 30 seconds. 3. Using the Remote, send the Remote start command to turn remote start off. Virtual Tach is programmed. To reset Virtual Tach, a module reset must be done.

Note: Virtual Tach cannot be used in Manual Transmission Mode. It is also not recommended for diesel trucks.

Virtual Tach handles disengaging the starter motor during remote starting – it does not address over-rev. If the customer wants to have the over-rev protection capability, the tach wire or data tach must be used.

Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence.

41 DS4+ VW10 © 2017-11-02 Directed. All rights reserved. Limited lifetime consumer warranty Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace (at Directed’s election) with a comparable reconditioned model any Directed unit (hereafter the “unit”), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was purchased from an authorized Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address; the authorized dealers name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. ALL PRODUCTS RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF PURCHASE FROM AN AUTHORIZED DEALER WILL BE DENIED. This warranty is non-transferable and is automatically void if: the unit’s date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. Directed, in its sole discretion, will determine what constitutes excessive damage and may refuse the return of any unit with excessive damage.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGE TO VEHICLE, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE SUBJECT TO THE CONDITIONS AS DESCRIBED HEREIN. THIS WARRANTY IS VOID IF THE UNIT HAS NOT BEEN PURCHASED FROM DIRECTED, OR AN AUTHORIZED DIRECTED DEALER, OR IF THE UNIT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, ACTS OF GOD, NEGLECT, IMPROPER SERVICE, OR OTHER CAUSES NOT ARISING OUT OF DEFECT IN MATERIALS OR CONSTRUCTION.

Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State.

This warranty is only valid for sale of product(s) within the United States of America and in Canada. Product(s) sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied.

For further details relating to warranty information of Directed products, please visit the support section of Directed’s website at: www.directed.com.

This product may be covered by a Guaranteed Protection Plan (“GPP”). See your authorized Directed dealer for details of the plan or call Directed Customer Service at 1-800-876-0800.

(920-10011-01 2011-06)

Sending commands to your vehicle Pit stop/idle mode Whether you want to remote start the engine, lock/unlock the doors or pop the trunk, there are 3 possible ways you can send commands to your vehicle, using the: Stop the vehicle in a safe parking spot and put the Put gear in • Factory remote. 1 gear in Park (P). Park • Aftermarket remote. Press the Remote Start button on the transmitter.* • Directed SmartStart application via your smartphone. 14:36 & 2 The parking lights will flash once to indicate the If applicable, you can also start the engine remotely by pressing the Lock button 3 Press Remote Parking lights flash x1 vehicle is now in Pit Stop Mode. Start button* times quickly on your factory remote. It is safe to leave the engine running and exit the Vehicle takeover with regular key vehicle with the factory remote in hand. 3 14:36 Note: We recommend that you always lock the Exit vehicle with remote Close the vehicle doors, hood and trunk, then send Press Remote doors of your vehicle14:36 when leaving it unattended. 1 the Remote Start command to start the vehicle.* Start button* * Icon and remote appearance may differ depending on the model purchased. Send the Unlock command on the factory or Press Unlock on 2 aftermarket remote.* either remote* List of available commands14:36 Note that the information below is for many Viper, Clifford, Python, Autostart and Enter the vehicle, while making sure the factory 14:36 AstroStart models. Icons and commands may differ depending on the model and 3 remote is inside with you. Enter vehicle options purchased. Refer to your authorized installation center for more specific with remote information.

ey O OFF ey OFF ey OFF ey OFF Insert your key in the ignition barrel and turn it to Othe O O O 4 S S S S ON position. Button(s) Actions Depress the brake pedal, put the car in gear and Ready to Press & hold for 1 second to lock. 5 drive off. drive off Press & hold for 1 second to unlock. * Icon and remote appearance may differ depending on the model purchased. * Press & hold for 1 second to remote start. * Press & hold for 5 seconds to activate the trunk release (optional).

* Icon and remote appearance may differ depending on the model purchased.

DS4+ VW10 © 2017-11-02 Directed. All rights reserved. SmartStart compatible This system is compatible with Directed SmartStart. For a complete list of supported features, please visit www.mysmartstart.com.

What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system: • Lock/Arm • Unlock/Disarm • Remote Car Starter • Trunk Release • Panic • Aux Channels

You can also control multiple vehicles – great for families – and assign more than one user to control a vehicle. It’s easy with SmartStart! But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, parked car finder and more.

The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.

For more information, visit www.mysmartstart.com.

Notes