Installation Instructions for ALL Unit and Disconnect the Wiring

Home , Chevrolet Astro, Chevrolet Lumina APV

KIT FEATURES TABLE OF CONTENTS

Works with any Metra GM CAR PAGE CAR PAGE BUICK CHEVROLET (cont.) J-body kit 02-4544 Roadmaster 1991-94...... 4 Van (full) 1988-95...... 9 CADILLAC GMC Cimarron 1982-88...... 4 S15 Jimmy 1982-85...... 8 KIT COMPONENTS INSTALLATION CHEVROLET S15 Jimmy 1986-94...... 8 Astro 1985-89...... 2 S15 Pickup 1982-85...... 8 Astro 1990-95...... 1 S15 Pickup 1986-93...... 8 Bracket Set #1 INSTRUCTIONS Beretta 1991-96...... 2 Safari 1985-89...... 2 Camaro 1982-84...... 3 Safari 1990-95...... 1 Camaro 1985-92...... 3 Van (full) 1988-95...... 9 Caprice 1991-93...... 4 OLDSMOBILE Cavalier 1982-90...... 4 Bravada 1991-94...... 8 Cavalier 1991-94...... 5 Omega 1983-84...... 9 Bracket APPLICATIONS Corsica 1991-96...... 2 Silhouette 1990-95...... 6 Set #2 El Camino 1985-88...... 5 Silhouette 1996...... 7 Lumina 1990-94...... 6 PONTIAC Bracket GENERAL MOTORS 1982-96 Lumina APV 1990-95...... 6 6000 1982-91...... 10 #(L) S-10 Lumina APV 1996...... 7 Firebird 1982-84...... 3 VEHICLES EQUIPPED WITH J-2000 PANEL-STYLE Monte Carlo 1985-88...... 5 Firebird 1985-92...... 3 FACTORY HEAD UNIT PROVISIONS Nova 1985-88...... 7 Grand Prix 1990-93...... 10 S10 Blazer 1982-85...... 8 Sunbird J-2000 1982-88...... 4 Bracket #3 (SEE INSIDE FOR SPECIFIC APPLICATIONS) S10 Blazer 1986-94...... 8 TransSport 1990-95...... 6 S10 Pickup 1982-85...... 8 TransSport 1996...... 7 Bracket #4 S10 Pickup 1986-93...... 8 SATURN (all models) 1991-94...... 11

Bracket Set #5 CHEVROLET Astro / GMC Safari 1990-95

Bracket #6 2 1 "A"

Bracket #7

(4) Keps Nuts

(4) Carriage Bolts

TOOLS REQUIRED

Phillips screwdriver Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Remove Bracket Set #1 EXCEPT tabs "A". The (2) screws from the bottom of the dash trim mounting tabs can be identified by the bezel. Gently unclip and remove the bezel. stamped letter on the back of each tab. Skip Cutting tool Remove (4) screws from the factory head to the Installation Instructions for ALL unit and disconnect the wiring. VEHICLES on Page #11. 1-800-221-0932 www.metraonline.com 1 rev. 300701Socket wrench © COPYRIGHT 2001 METRA ELECTRONICS CORPORATION CHEVROLET Astro / GMC Safari 1985-89 CHEVROLET Camaro / PONTIAC Firebird 1982-84

1 2 1 2 "A"

"A"

Disconnect the negative battery terminal to Cut and remove all mounting tabs on Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Remove Bracket #3 EXCEPT tabs "A". The prevent an accidental short circuit. Remove Bracket Set #2 EXCEPT those tabs with (3) Phillips screws from the top portion of the mounting tabs can be identified by the (4) star-drive screws from the dash trim holes "A". The mounting tabs can be dash trim bezel. Open the glove box and stamped letter on the back of each tab. Skip bezel and remove the bezel. Remove (4) identified by the stamped letter on the back remove (2) 10mm bolts from the lower edge to the Installation Instructions for ALL screws securing the factory head unit and of each tab. Skip to the Installation of the trim bezel. Pull the console trim VEHICLES on Page #11. disconnect the wiring. Instructions for ALL VEHICLES on Page forward and remove (2) 7mm bolts exposed. #11. Gently unclip and remove the trim bezel. Remove (2) 7mm screws from the factory head unit and disconnect the wiring.

CHEVROLET Camaro / PONTIAC Firebird 1985-92 CHEVROLET Beretta / Corsica 1991-96 1 2 1 2

"B"

Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Remove Bracket Set #2 EXCEPT those tabs with Disconnect the negative battery terminal to Locate Bracket #7. (No cutting is required). (4) star-drive screws from the dash trim holes "B". The mounting tabs can be prevent an accidental short circuit. Using a Skip to the Installation Instructions for ALL bezel and remove the bezel. Remove (4) identified by the stamped letter on the back panel removal tool, pry outward on the dash VEHICLES on Page #11. screws securing the factory head unit and of each tab. Skip to the Installation trim bezel and remove. Remove (2) screws disconnect the wiring. Instructions for ALL VEHICLES on Page securing the factory head unit and #11. disconnect the wiring.

2 3 CHEVROLET Caprice 1991-93 CHEVROLET Cavalier 1991-94 BUICK Roadmaster 1991-94 1 2 1 2

"B" "B"

"B"

Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Using a Bracket Set #3 EXCEPT tabs "B". The Disconnect the negative battery terminal to Cut and remove all mounting tabs on panel removal tool, carefully pry out on the mounting tabs can be identified by the prevent an accidental short circuit. Remove Bracket #4 EXCEPT tabs "B". The dash trim bezel and remove. Remove (2) stamped letter on the back of each tab. Skip (2) screws from the driver's side service mounting tabs can be identified by the screws securing the factory head unit and to the Installation Instructions for ALL panel and unclip the panel. Pry off the trim stamped letter on the back of each tab. Skip disconnect the wiring. VEHICLES on Page #11. piece located above the glove box and to the Installation Instructions for ALL remove (1) screw. Remove (3) screws from VEHICLES on Page #11. the top edge of the dash trim bezel. Remove (1) screw from the lower-left corner of the glove box and (1) screw from the parking brake release. Remove the dash trim bezel.

CHEVROLET Cavalier 1982-90 / Cadillac Cimarron 1982-88 CHEVROLET El Camino / Monte Carlo 1985-88 PONTIAC Sunbird J-2000 1982-88 1 2 1 2 "C" "A"

"C"

"A" "C"

"C"

Disconnect the negative battery terminal to Cut and remove all mounting tabs on Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Remove Bracket Set #2 EXCEPT tabs "C". The prevent an accidental short circuit. Remove Bracket #4 EXCEPT tabs "A". The (4) screws from the dash trim bezel. mounting tabs can be identified by the (6) star-drive screws from the dash trim mounting tabs can be identified by the Remove the bezel and disconnect the stamped letter on the back of each tab. Skip bezel and remove the bezel. Remove (2) stamped letter on the back of each tab. Skip cigarette lighter wiring. to the Installation Instructions for ALL screws from the factory head unit and to the Installation Instructions for ALL VEHICLES on Page #11. disconnect the wiring. VEHICLES on Page #11. 4 5 CHEVROLET Lumina 1990-94 CHEVROLET Lumina APV / OLDSMOBILE Silhouette 1 2 PONTIAC TransSport 1996 "A" 1 2 "A" "B" "A"

"A" "B"

Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Remove Bracket Set #5 EXCEPT tabs "A". The (2) screws from the lower steering column mounting tabs can be identified by the Disconnect the negative battery terminal to panel. Pull the panel down to access the stamped letter on the back of each tab. Skip prevent an accidental short circuit. Remove Cut and remove all mounting tabs on bottom portion of the radio trim bezel. Pull to the Installation Instructions for ALL (1) Phillips screw from each side of the Bracket Set #6 EXCEPT tabs "B". The the top and bottom edges of the bezel VEHICLES on Page #11. center console. Open the glove box and mounting tabs can be identified by the forward and remove. remove (2) Phillips screws exposed. stamped letter on the back of each tab. Skip Remove (2) 7mm hex-head screws and (1) to the Installation Instructions for ALL pop-clip from the lower steering column VEHICLES on Page #11. panel, and (2) Phillips screws exposed near the climate controls. Remove (1) 7mm hex- head screw under the glove box. Pull out on CHEVROLET Lumina APV / OLDSMOBILE Silhouette the center console and remove. PONTIAC TransSport 1990-95 CHEVROLET Nova 1985-88 1 2 "B" 1 2 "B"

"B"

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove Cut and remove all mounting tabs on (2) screws securing the lower steering Bracket Set #6 EXCEPT tabs "B". The Disconnect the negative battery terminal to Cut and remove all mounting tabs on column panel and remove. Remove (2) mounting tabs can be identified by the prevent an accidental short circuit. Remove Bracket Set #1 EXCEPT tabs "B". The screws exposed on the left tab of the radio stamped letter on the back of each tab. Skip the ashtray and (2) screws from the ashtray mounting tabs can be identified by the trim bezel. Open the glove box and remove to the Installation Instructions for ALL bracket. Remove (2) screws above the stamped letter on the back of each tab. Skip (2) screws exposed on the right tabs of the VEHICLES on Page #11. radio opening and remove the radio trim to the Installation Instructions for ALL radio trim bezel. bezel. VEHICLES on Page #11. 6 7 CHEVROLET S10 Pickup 1982-85 / S10 Blazer 1982-85 CHEVROLET Van (full size) 1988-95 GMC S15 Pickup 1982-85 / S15 Jimmy 1982-85 GMC Van (full size) 1988-95

1 2 "B" 1 2

"B" "B" "C"

"C" "B"

Disconnect the negative battery terminal to Cut and remove all mounting tabs on Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Remove Bracket Set #5 EXCEPT tabs "B". The prevent an accidental short circuit. Carefully Bracket Set #1 EXCEPT tabs "C". The (4) star-drive screws from the corners of the mounting tabs can be identified by the unsnap the radio trim bezel and remove. mounting tabs can be identified by the dash trim bezel. Remove (1) star-drive stamped letter on the back of each tab. Skip Remove (2) screws securing the factory stamped letter on the back of each tab. Skip screw from the lower-right corner of the to the Installation Instructions for ALL head unit and disconnect the wiring. to the Installation Instructions for ALL instrument cluster panel and remove the VEHICLES on Page #11. VEHICLES on Page #11. dash trim bezel. CHEVROLET S10 Pickup 1986-93 / S10 Blazer 1986-94 GMC S15 Pickup 1986-93 / S15 Jimmy 1986-94 OLDSMOBILE Bravada 1991-94 OLDSMOBILE Omega 1983-84

1 2 1 2 "C"

"B" "C"

"C"

Disconnect the negative battery terminal to Locate Bracket #(L) S-10 and the right Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Remove Bracket from Bracket Set #5. Cut and prevent an accidental short circuit. Remove Bracket Set #2 EXCEPT tabs "C". The the ashtray and (1) screw inside the ashtray remove all mounting tabs on the right (4) hex-head washer screws from the mounting tabs can be identified by the cavity. Open the glove box and remove (2) Bracket EXCEPT top tab "B". (No cutting is steering column trim panel, pull down on the stamped letter on the back of each tab. Skip screws exposed on the edge of the dash trim required on Bracket #(L) S-10). The rear edge of the panel and remove. Remove to the Installation Instructions for ALL bezel. mounting tabs can be identified by the (4) Phillips screws from the top edge of the VEHICLES on Page #11. stamped letter on the back of each tab. Skip dash trim bezel. Remove (2) hez-head to the Installation Instructions for ALL washer screws from the bottom of the dash VEHICLES on Page #11. trim bezel and remove the bezel. 8 9 PONTIAC 6000 1982-91 SATURN (all models) 1991-94

1 2 1 2

"A" "A" "A" "A"

"A"

Disconnect the negative battery terminal to Cut and remove all mounting tabs on Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Open Bracket #5 EXCEPT tabs "A". The prevent an accidental short circuit. Gently Bracket #6 EXCEPT tabs "A". The the glove box and remove (1) screw from the mounting tabs can be identified by the unclip the dash trim bezel. Remove (2) mounting tabs can be identified by the side of the radio trim bezel. Gently remove stamped letter on the back of each tab. Skip screws from the factory head unit and stamped letter on the back of each tab. Skip the bezel from the dash and the dummy to the Installation Instructions for ALL disconnect the wiring. to the Installation Instructions for ALL plate from the bezel. VEHICLES on Page #11. VEHICLES on Page #11.

ALL VEHICLES

PONTIAC Grand Prix 1990-93 3

Fig. B 1 2 "B" Fig. A

"B"

(SHOWN WITH 99-4544 AS EXAMPLE)

(SHOWN WITH 99-4544 AS EXAMPLE) Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Remove Bracket #6 EXCEPT tabs "B". The (1) 9/32" hex-head screw from the computer mounting tabs can be identified by the TOP AND/OR BOTTOM MOUNTING BRACKETS: Using the Radio Housing from one of diagnostic plug and twist to access (1) 9/32" stamped letter on the back of each tab. Skip Metra's GENERAL MOTORS J-body kits, secure the Mounting Bracket(s) to the Housing with screw on the trim panel. Remove (3) 9/32" to the Installation Instructions for ALL Carriage Bolts and Keps Nuts. (see Fig. A) screws from the bottom edge of the panel VEHICLES on Page #11. and remove. Open the glove box and SIDE MOUNTING BRACKETS: Using the Radio Housing from one of Metra's GENERAL remove (4) 9/32" screws from the dash trim MOTORS J-body kits, ecure the Mounting Brackets to the Housing (through the center holes) bezel. with Carriage Bolts and Keps Nuts. (see Fig. B) 10 11 4 Fig. A

Fig. B

2-SHAFT HEAD UNITS: Slide the aftermarket head unit into the kit and secure with shaft nuts. (see Fig. A)

DIN HEAD UNITS: Cut and remove the shaft supports. Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. Slide the aftermarket head unit into the cage until secure. (see Fig. B)

56 A

B C

A) Strip wire ends back ½" B) Twist ends together C) Solder D) Tape

Locate the factory wiring harness in the Re-connect the battery terminal and test the unit dash. Metra recommends using the for proper operation. Mount the head unit/kit proper mating adaptor and making assembly to the sub-dash with those screws connections as shown. (Isolate and previously removed. individually tape off the ends of any unused wires to prevent electrical short circuit).