Installation Instructions
Total Page:16
File Type:pdf, Size:1020Kb
KIT COMPONENTS Radio Housing Metal 99-4512 Support Tray INSTALLATION INSTRUCTIONS Flat Faceplate APPLICATIONS ½" Faceplate GENERAL MOTORS 1982-96 VEHICLES EQUIPPED WITH J-2000 PANEL-STYLE 1" FACTORY HEAD UNIT PROVISIONS Faceplate (SEE INSIDE FOR SPECIFIC APPLICATIONS) Equalizer Faceplate Bracket Set #1 Bracket Set #2 Bracket #3 Bracket Bracket #4 #(L) S-10 Bracket Set #5 Bracket #6 Bracket #7 TOOLS REQUIRED 1-800-221-0932 www.metraonline.com rev. 030701 Phillips screwdriver © COPYRIGHT 2001 METRA ELECTRONICS CORPORATION TABLE OF CONTENTS NOTES: ______________________________________________________ ________________________________________________________________ CAR PAGE CAR PAGE BUICK CHEVROLET (cont.) Roadmaster 1991-94.............. 4 Van (full) 1988-95....................9 ________________________________________________________________ CADILLAC GMC Cimarron 1982-88................... 4 S15 Jimmy 1982-85................ 8 ________________________________________________________________ CHEVROLET S15 Jimmy 1986-94................ 8 Astro 1985-89..........................2 S15 Pickup 1982-85................8 Astro 1990-95..........................1 S15 Pickup 1986-93................8 ________________________________________________________________ Beretta 1991-96...................... 2 Safari 1985-89.........................2 Camaro 1982-84..................... 3 Safari 1990-95........................ 1 Camaro 1985-92..................... 3 Van (full) 1988-95....................9 ________________________________________________________________ Caprice 1991-93..................... 4 OLDSMOBILE Cavalier 1982-90.....................4 Bravada 1991-94.................... 8 Cavalier 1991-94.....................5 Omega 1983-84...................... 9 ________________________________________________________________ Corsica 1991-96..................... 2 Silhouette 1990-95.................. 6 El Camino 1985-88................. 5 Silhouette 1996....................... 7 ________________________________________________________________ Lumina 1990-94...................... 6 PONTIAC Lumina APV 1990-95.............. 6 6000 1982-91.......................... 10 Lumina APV 1996................... 7 Firebird 1982-84......................3 ________________________________________________________________ Monte Carlo 1985-88.............. 5 Firebird 1985-92......................3 Nova 1985-88..........................7 Grand Prix 1990-93.................10 S10 Blazer 1982-85.................8 Sunbird J-2000 1982-88..........4 ________________________________________________________________ S10 Blazer 1986-94.................8 TransSport 1990-95................ 6 S10 Pickup 1982-85................8 TransSport 1996......................7 ________________________________________________________________ S10 Pickup 1986-93............... 8 SATURN (all models) 1991-94............... 11 ________________________________________________________________ (FACTORY BRACKETS MUST BE RETAINED AND USED WITH VEHICLES NOT LISTED ABOVE) ________________________________________________________________ CHEVROLET Astro / GMC Safari 1990-95 ________________________________________________________________ 2 ________________________________________________________________ 1 "A" ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ ________________________________________________________________ Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Remove Bracket Set #1 EXCEPT tabs "A". The ________________________________________________________________ (2) screws from the bottom of the dash trim mounting tabs can be identified by the bezel. Gently unclip and remove the bezel. stamped letter on the back of each tab. Skip ________________________________________________________________ Remove (4) screws from the factory head to the Installation Instructions for ALL unit and disconnect the wiring. VEHICLES on Page #11. 1 14 7 CHEVROLET Astro / GMC Safari 1985-89 Fig. A 1 2 "A" Fig. B "A" 2-SHAFT HEAD UNITS: Slide the aftermarket head unit into the kit and secure with shaft nuts. Be sure the Rear Support Bullet on the unit engages the Rear Support Bracket on the Metal Support Tray. (see Fig. A) Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Remove Bracket #3 EXCEPT tabs "A". The DIN HEAD UNITS: Cut and remove the shaft supports from the Faceplate. Slide the DIN (3) Phillips screws from the top portion of the mounting tabs can be identified by the cage into the kit and secure by bending the metal locking tabs down. Slide the aftermarket dash trim bezel. Open the glove box and stamped letter on the back of each tab. Skip head unit into the cage until secure. Be sure the Rear Support Bullet on the unit engages the remove (2) 10mm bolts from the lower edge to the Installation Instructions for ALL Rear Support Bracket on the Metal Support Tray. (see Fig. B) of the trim bezel. Pull the console trim VEHICLES on Page #11. forward and remove (2) 7mm bolts exposed. (If an equalizer will be included, slide the unit into the back of the Radio Housing and secure. Gently unclip and remove the trim bezel. If an equalizer will NOT be included, snap the Equalizer Dummy Plate into the opening). Remove (2) 7mm screws from the factory head unit and disconnect the wiring. 8 9 A CHEVROLET Beretta / Corsica 1991-96 B C 1 2 D A) Strip wire ends back ½" B) Twist ends together C) Solder D) Tape Locate the factory wiring harness in the Re-connect the battery terminal and test the unit dash. Metra recommends using the for proper operation. Mount the head unit/kit proper mating adaptor and making assembly to the sub-dash with those screws Disconnect the negative battery terminal to Locate Bracket #7. (No cutting is required). connections as shown. (Isolate and previously removed. prevent an accidental short circuit. Using a Skip to the Installation Instructions for ALL individually tape off the ends of any panel removal tool, pry outward on the dash VEHICLES on Page #11. unused wires to prevent electrical short trim bezel and remove. Remove (2) screws circuit). securing the factory head unit and disconnect the wiring. 13 2 CHEVROLET Camaro / PONTIAC Firebird 1982-84 5 "C" "B" Fig. B "C" 1 2 "B" "A" "A" "B" "A" "B" "A" "B" Fig. A "A" "B" "A" Fig. C Disconnect the negative battery terminal to Cut and remove all mounting tabs on "A" prevent an accidental short circuit. Remove Bracket Set #2 EXCEPT those tabs with (4) star-drive screws from the dash trim holes "A". The mounting tabs can be TOP MOUNTING BRACKETS: Slide the Radio Housing onto the Metal Support Tray and mount bezel and remove the bezel. Remove (4) identified by the stamped letter on the back with (2) Carriage Bolts and (2) Keps Nuts ("A"). Mount the Equalizer Brackets to the Radio screws securing the factory head unit and of each tab. Skip to the Installation Housing with (2) Carriage Bolts and (2) Keps Nuts ("B"). Mount the factory bracket to the top of the disconnect the wiring. Instructions for ALL VEHICLES on Page Housing with (2) Carriage Bolts and (2) Keps Nuts ("C"). (see Fig. A) #11. SIDE MOUNTING BRACKETS: Slide the Radio Housing onto the Metal Support Tray and mount with (2) Carriage Bolts and (2) Keps Nuts ("A"). Mount the Equalizer Brackets to the Housing assembly (through the side holes) with (2) Carriage Bolts and (2) Keps Nuts ("B"). (see Fig. B) BOTTOM MOUNTING BRACKETS: Slide the Radio Housing onto the Metal Support Tray and mount the factory bracket to the Housing (through the holes in the Tray) with (2) Carriage Bolts and CHEVROLET Camaro / PONTIAC Firebird 1985-92 (2) Keps Nuts ("A"). Mount the Equalizer Brackets to the Housing with (2) Carriage Bolts and (2) Keps Nuts ("B"). (see Fig. C) 2 1 6 Fig. A "B" Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Remove Bracket Set #2 EXCEPT those tabs with (4) star-drive screws from the dash trim holes "B". The mounting tabs can be bezel and remove the bezel. Remove (4) identified by the stamped letter on the back screws securing the factory head unit and of each tab. Skip to the Installation disconnect the wiring. Instructions for ALL VEHICLES on Page #11. Mount the Rear Support Bracket to the Metal Support Tray with (2) Hex-head Screws supplied. The mounting location may vary depending on the depth of the installation. (See Fig A). Screw the Rear Support Bullet onto the back of the aftermarket head unit. 3 12 SATURN (all models) 1991-94 CHEVROLET Caprice 1991-93 BUICK Roadmaster 1991-94 1 2 1 2 "A" "B" "A" Disconnect the negative battery terminal to Cut and remove all mounting tabs on prevent an accidental short circuit. Gently Bracket #6 EXCEPT tabs "A". The unclip the dash trim bezel. Remove (2) mounting tabs can be identified by the Disconnect the negative battery terminal to Cut and remove all mounting tabs on screws from the factory head unit and stamped letter on the back of each tab. Skip prevent an accidental short circuit. Remove Bracket #4 EXCEPT tabs "B". The disconnect the wiring. to the Installation Instructions for ALL (2) screws from the driver's side service mounting tabs can be identified by the VEHICLES on Page #11. panel and unclip the panel. Pry off