DOCSLIB.ORG

Polysulfone Chemical Compatibility Chart

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Polysulfone Chemical Compatibility Chart ver 04-Feb-2019 Polysulfone Chemical Compatibility Chart Chemical Rating Chemical Rating 1,4-Dioxane, pure X Aluminum chloride, pure A 2,2,4-Trimethylpentane, pure4 A Aluminum hydroxide B 2,4,6-Trinitrophenol X Aluminum salts, pure A 2-Methoxyethanol X Aluminum trichloride, 10% A 2-Propanol, pure4 A Amino acid, pure A Acetaldehyde X Aminoethanol (2-) A Acetamide X Ammonia, 25%2 A Acetic acid, 5% A Ammonia, 29%2 A Acetic acid, 10% A Ammonia4 B Acetic acid, 20% A Ammonium acetate, saturated A Acetic acid, 50%1 A Ammonium chloride, 10% A Acetic acid, glacial1 A Ammonium chloride, pure A Acetic anhydride X Ammonium glycolate, pure A Acetone, 5% A Ammonium hydroxide, 5%1 A Acetone, 50% A Ammonium hydroxide, 15%1 A Acetone, 60%2 A Ammonium hydroxide, 29%1 A Acetone, pure X Ammonium hydroxide, 30%1 A Acetonitrile X Ammonium nitrate, 10% A Acetophenone X Ammonium oxalate, pure A Acetyl chloride X Ammonium persulfate, 24% A Acrylonitrile X Ammonium salts, pure A Adhesive (Eastman 910) A Ammonium sulfate, 10% A Adipic acid, pure A Amyl acetate X Alanine, pure A Amyl alcohol A Alconox, 1% A Amyl alcohol, pure A Allyl alcohol4 B Amyl chloride X Aluminum sulfate, 10% A Aniline X A = Little or no interaction B = Slight interaction X = Not recommended Room temperature = 20°C or 68°F (1) Elevated temperatures may reduce resistance --- (2) Exposure to elevated stress may damage polymer (3) Prolonged exposure may reduce resistance --- (4) Room Temperature only It is the sole responsibility of the system designer and user to select products suitable for their specific application requirements and to ensure proper installation, operation, and maintenance of these products. Material compatibility, product ratings and application details should be considered in the selection. Improper selection or use of products described herein can cause personal injury or product damage. Industrial Specialties Mfg. 4091 S. Eliot St., Englewood, CO 80110-4396 ISM and IS MED Specialties Phone 303-781-8486 I Fax 303-761-7939 industrialspec.com ismedspec.com © Copyright 2019 Industrial Specialties Mfg. Polysulfone Chemical Compatibility Chart ver 04-Feb-2018 Chemical Rating Chemical Rating Anti-Freeze2 A Butter, salted2 A Antimony trichloride X Butyl acetate X Aqua regia, pure X Butyl alcohol A Automotive grease2 A Butyl cellosolve A Aviation gasoline (100 octane)3 B Butyl chloride X Barbitol solvent A Butyl ether A Barium chloride, 10% A Butyl phthalate X Benzaldehyde X Butylamine (n-) X Benzenamine X Butylated hydroxy anisole X Benzene X Butylated hydroxy toluene A Benzene sulfonic acid X Butyraldehyde X Benzoic acid3 B Butyric acid X Benzol, pure X Calcium chloride, saturated A Benzonitrile X Calcium dinitrate, 10% A Benzyl acetate X Calcium hydroxide B Benzyl alcohol X Calcium hypochlorite, 3.5%3 A Benzyl chloride X Calcium hypochlorite, saturated3 A Black liquor1 A Calcium propionate2 A Boric acid A Calgon liquid A Brake fluid X Carbitol A Brine A Carbazole X Bromine, 10%1,3 B Carbon disulfide X Bromine, pure X Carbon tetrachloride3 A Bromobenzene X Carbon Tetrachloride X Bromoform X Caustic potash, 30%4 A Butadiene X Caustic potash, 50%4 A Butanol2 A Caustic potash, concentrated4 A A = Little or no interaction B = Slight interaction X = Not recommended Room temperature = 20°C or 68°F (1) Elevated temperatures may reduce resistance --- (2) Exposure to elevated stress may damage polymer (3) Prolonged exposure may reduce resistance --- (4) Room Temperature only It is the sole responsibility of the system designer and user to select products suitable for their specific application requirements and to ensure proper installation, operation, and maintenance of these products. Material compatibility, product ratings and application details should be considered in the selection. Improper selection or use of products described herein can cause personal injury or product damage. Industrial Specialties Mfg. 4091 S. Eliot St., Englewood, CO 80110-4396 ISM and IS MED Specialties Phone 303-781-8486 I Fax 303-761-7939 industrialspec.com ismedspec.com © Copyright 2019 Industrial Specialties Mfg. Polysulfone Chemical Compatibility Chart ver 04-Feb-2018 Chemical Rating Chemical Rating Caustic soda, 1% A Corn oil2 A Caustic soda, 50%1 A Cotton Seed oil2 A Cedarwood oil3 B Cresol (m-) X Cellosolve (2-ethoxyethanol) A Cresol X Cellosolve acetate X Cresyl Diphenyl phosphate X Cellosolve solvent4 A Cupric chloride, saturated A Chlorine, water solution X Cyclohexane2 A Chlorine, dry gas, 10% X Cyclohexane X Chlorine, wet gas X Cyclohexanol A Chlorine, wet gas, 10% X Cyclohexanone X Chloroacetic acid X Cyclopentane X Chlorobenzene X Decahydronaphthalene X Chloroethanol (2-) X Decalin, pure X Chloroform X Diacetone, pure X Chlorophenol, 5% X Diacetone alcohol X Chromic acid, 10%2 A Dibutyl phthalate, pure X Chromic acid, 12%2 A Dichlorobenzene (p-), vapor X Chromic acid, 20% X Dichlorodifluoromethane (Freon 12) A Chromic acid, 50% X Dichloromethane X Chromic acid, 60% X Diesel fuel A Chromic acid, sulfuric acid mixture, 96% X Diesel fuel (fuel oil #2) A Cinnamon oil3 B Diethyl benzene X Citric acid, 2% A Diethyl ether X Citric acid, 10% A Diethyl ketone X Citric acid, 40% A Diethyl malonate3 B Citric acid, 1M A Diethylamine1,3 B Copper sulphate, pure A Diethylene dioxide X A = Little or no interaction B = Slight interaction X = Not recommended Room temperature = 20°C or 68°F (1) Elevated temperatures may reduce resistance --- (2) Exposure to elevated stress may damage polymer (3) Prolonged exposure may reduce resistance --- (4) Room Temperature only It is the sole responsibility of the system designer and user to select products suitable for their specific application requirements and to ensure proper installation, operation, and maintenance of these products. Material compatibility, product ratings and application details should be considered in the selection. Improper selection or use of products described herein can cause personal injury or product damage. Industrial Specialties Mfg. 4091 S. Eliot St., Englewood, CO 80110-4396 ISM and IS MED Specialties Phone 303-781-8486 I Fax 303-761-7939 industrialspec.com ismedspec.com © Copyright 2019 Industrial Specialties Mfg. Polysulfone Chemical Compatibility Chart ver 04-Feb-2018 Chemical Rating Chemical Rating Dimethyl formamide X Ethyl chloride X Diethylene glycol X Ethyl cyanoacetate X Diethylene glycol monoethyl ether X Ethyl lactate X Dimethyl acetamide, pure X Ethylbutyric acid (2-) A Dimethyl formamide, pure X Ethylene chloride X Dimethyl sulfoxide X Ethylene dichloride X Dimethylaniline X Ethylene glycol A Dimethylformamide (N,N-) X Ethylene glycol, pure A Dimethylsulfoxide, 50% (DMSO) B Ethylene glycol monomethyl ether X Dimethylsulfoxide, pure (DMSO) X Ethylene oxide A Dioctylphthalate2 (dioctyl phthalate) A Ethylene oxide, gas A Dioxane (p-) X Ethylene oxide, pure A Dipropylene glycol3 B Ethylenediamine, 92%4 A DMSO X EtO, gas (ethylene oxide) A Dowtherm X EtO, pure (ethylene oxide) A Epichlorohydrin X Fatty acids - saturated B Ethanol1,2 A Fatty acids - unsaturated B Ethanol, 40%1,2 B Ferric chloride, 10% A Ether X Ferrous sulfate, saturated A Ethyl acetate X Fluorides A Ethyl alcohol, 15% A Fluorine, gas X Ethyl alcohol, 40%1,2 B Formaldehyde, 2% A Ethyl alcohol, 95%1,2 B Formaldehyde, 30% A Ethyl alcohol, pure1,2 B Formaldehyde, 10% A Ethyl benzene X Formaldehyde, 37%1 A Ethyl benzoate X Formaldehyde, 40%1 A Ethyl butyrate X Formalin, 10% A A = Little or no interaction B = Slight interaction X = Not recommended Room temperature = 20°C or 68°F (1) Elevated temperatures may reduce resistance --- (2) Exposure to elevated stress may damage polymer (3) Prolonged exposure may reduce resistance --- (4) Room Temperature only It is the sole responsibility of the system designer and user to select products suitable for their specific application requirements and to ensure proper installation, operation, and maintenance of these products. Material compatibility, product ratings and application details should be considered in the selection. Improper selection or use of products described herein can cause personal injury or product damage. Industrial Specialties Mfg. 4091 S. Eliot St., Englewood, CO 80110-4396 ISM and IS MED Specialties Phone 303-781-8486 I Fax 303-761-7939 industrialspec.com ismedspec.com © Copyright 2019 Industrial Specialties Mfg. Polysulfone Chemical Compatibility Chart ver 04-Feb-2018 Chemical Rating Chemical Rating Formalin, 40%1,3 B Hydraulic oil A Formic acid, 3%1 A Hydrazine X Formic acid, 10%1 B Hydrobromic acid, 20% A Formic acid, 25%1 B Hydrobromic acid, 69%1 A Formic acid, 50%1 B Hydrochloric acid, 5%2 A Formic acid, 88%1 X Hydrochloric acid, 20%2 A Formic acid, 100%1 X Hydrochloric acid, 37%1 A Formic acid, pure1 X Hydrofluoric acid, 4%1,3 B Freon 111 A Hydrofluoric acid, 25%1,3 A Freon TF, pure1 B Hydrofluoric acid, 50%1,3 A Freon TMC X Hydrogen peroxide A Freon TMS2 A Hydrogen peroxide, 3% A Fuel oil1 A Hydrogen peroxide, 30% A Furfural X Hydrogen peroxide, 90% A Gasoline2 A Iodine solutions X Glutaraldehyde B Isobutanol, pure1 A Glutaraldehyde disinfectant B Isobutyl alcohol A Glycerin, pure A Isobutyl alcohol, pure1 A Glycerol, pure A Isooctane A Grape juice A Isopropanol1,3 B Grease2 A Isopropanol, 100%1,3 B Green liquor A Isopropanol, pure1,3 B Heptane (n-)2 A iso-Propanol, 100%1,3 B Heptane, 0.05% A Isopropyl acetate X Hexane (n-)2 B Isopropyl alcohol A Hexane1 B Isopropyl alcohol, 100%1,3 B Hexanol A Isopropyl alcohol, pure1,3 B A = Little or no interaction B = Slight interaction X = Not recommended Room temperature = 20°C or 68°F (1) Elevated temperatures may reduce resistance --- (2) Exposure to elevated stress may damage polymer (3) Prolonged exposure may reduce resistance --- (4) Room Temperature only It is the sole responsibility of the system designer and user to select products suitable for their specific application requirements and to ensure proper installation, operation, and maintenance of these products.
Load more

Recommended publications
  • Provisional Peer-Reviewed Toxicity Values for Sulfolane (Casrn 126-33-0)
    EPA/690/R-12/024F l Final 1-30-2012 Provisional Peer-Reviewed Toxicity Values for Sulfolane (CASRN 126-33-0) Superfund Health Risk Technical Support Center National Center for Environmental Assessment Office of Research and Development U.S. Environmental Protection Agency Cincinnati, OH 45268 AUTHORS, CONTRIBUTORS, AND REVIEWERS CHEMICAL MANAGER Dan D. Petersen, PhD, DABT National Center for Environmental Assessment, Cincinnati, OH DRAFT DOCUMENT PREPARED BY ICF International 9300 Lee Highway Fairfax, VA 22031 PRIMARY INTERNAL REVIEWERS Ghazi Dannan, PhD National Center for Environmental Assessment, Washington, DC Q. Jay Zhao, PhD, MPH, DABT National Center for Environmental Assessment, Cincinnati, OH This document was externally peer reviewed under contract to Eastern Research Group, Inc. 110 Hartwell Avenue Lexington, MA 02421-3136 Questions regarding the contents of this document may be directed to the U.S. EPA Office of Research and Development’s National Center for Environmental Assessment, Superfund Health Risk Technical Support Center (513-569-7300). i Sulfolane TABLE OF CONTENTS COMMONLY USED ABBREVIATIONS ................................................................................... iii BACKGROUND .............................................................................................................................1 DISCLAIMERS ...............................................................................................................................1 QUESTIONS REGARDING PPRTVS ...........................................................................................1
    [Show full text]
  • Development of Polysulfone Hollow Fiber Porous Supports for High Flux Composite Membranes: Air Plasma and Piranha Etching
    fibers Article Development of Polysulfone Hollow Fiber Porous Supports for High Flux Composite Membranes: Air Plasma and Piranha Etching Ilya Borisov 1,*, Anna Ovcharova 1,*, Danila Bakhtin 1, Stepan Bazhenov 1, Alexey Volkov 1, Rustem Ibragimov 2, Rustem Gallyamov 2, Galina Bondarenko 1, Rais Mozhchil 3, Alexandr Bildyukevich 4 and Vladimir Volkov 1 1 A.V. Topchiev Institute of Petrochemical Synthesis, Russian Academy of Sciences, Moscow 119991, Russia; [email protected] (D.B.); [email protected] (S.B.); [email protected] (A.V.); [email protected] (G.B.); [email protected] (V.V.) 2 Kazan National Research Technological University, Kazan 420015, Russia; [email protected] (R.I.); [email protected] (R.G.) 3 National Research Nuclear University “MEPhI”, Moscow 115409, Russia; [email protected] 4 Institute of Physical Organic Chemistry, National Academy of Sciences of Belarus, Minsk 220072, Belarus; [email protected] * Correspondence: [email protected] (I.B.); [email protected] (A.O.); Tel.: +7-495-955-4893 (I.B.); +7-495-647-59-27 (A.O.) Academic Editors: Alberto Figoli and Tao He Received: 30 December 2016; Accepted: 4 February 2017; Published: 13 February 2017 Abstract: For the development of high efficiency porous supports for composite membrane preparation, polysulfone (PSf) hollow fiber membranes (outer diameter 1.57 mm, inner diameter 1.12 mm) were modified by air plasma using the low temperature plasma treatment pilot plant which is easily scalable to industrial level and the Piranha etch (H2O2 + H2SO4). Chemical and plasma modification affected only surface layers and did not cause PSf chemical structure change.
    [Show full text]
  • Radel® PPSU, Udel® PSU, Veradel® PESU & Acudel® Modified PPSU
    Radel ® | Udel ® | Veradel ® | Acudel ® Radel® PPSU, Udel® PSU, Veradel® PESU & Acudel® modified PPSU Processing Guide SPECIALT Y POLYMERS 2 \ Sulfone Polymers Processing Guide Table of Contents Introduction ............................. 5 Part Ejection . 14 Draft . 14 Ejector pins and/or stripper plates . 14 Sulfone Polymers........................ 5 Udel® Polysulfone (PPSU) . 5 Injection Molding Equipment ............. 15 ® Veradel Polyethersulfone (PESU) . 5 Controls . 15 ® Radel Polyphenylsulfone (PPSU) . 5 Clamp . 15 ® Acudel modified PPSU . 5 Barrel Capacity . 15 Press Maintenance . 15 Resin Drying . .6 Screw Design . 15 Rheology................................ 8 Screw Tips and Check Valves . 15 Viscosity-Shear Rate ..................... 8 Nozzles . 16 Molding Process . 16 Resin Flow Characteristics . 9 Melt flow index . 9 Polymer Injection or Mold Filling . 16 Spiral flow . 9 Packing and Holding . 17 Injection Molding . .10 Cooling . 17 Molds and Mold Design .................. 10 Machine Settings ....................... 17 Tool Steels . 10 Barrel Temperatures . 17 Mold Dimensions . 10 Mold Temperature . 18 Mold Polishing . 10 Residence Time in the Barrel . 18 Mold Plating and Surface Treatments . 10 Injection Rate . 18 Tool Wear . 10 Back Pressure . 18 Mold Temperature Control . 10 Screw Speed . 18 Mold Types . 11 Shrinkage . 18 Two-plate molds . 11 Three-plate molds . 11 Regrind ............................... 19 Hot runner molds . 11 Cavity Layout . 12 Measuring Residual Stress ............... 19 Runner Systems . 12 Extrusion............................... 22 Gating . 12 Sprue gating . 12 Edge gates . 13 Predrying ............................. 22 Diaphragm gates . 13 Tunnel or submarine gates . 13 Extrusion Temperatures ................. 22 Pin gates . 13 Screw Design Recommendations . 22 Gate location . 13 Venting . 14 Sulfone Polymers Processing Guide / 3 Die Design ............................. 22 Extruded Product Types . 23 Wire . 23 Film . 23 Sheet . 23 Piping and tubing . 23 Start-Up, Shut-Down, and Purging .......
    [Show full text]
  • Groundwater and Soil  Oxygen and Nutrients (Soil Tilling, Blowers) (Biogenie, 2006)
    RemTech 2016 Brent Lennox, M.Sc., P.Geol., Senior Hydrogeologist Eric Pringle, M.A.Sc., P.Eng., Principal Hydrogeological Engineer Waterline Resources Inc. Used in Sulfinol for sour gas sweetening since 1960s Human health related guidelines Poorly adsorbed to soil High solubility in water Microbial degradation slow in typical groundwater conditions Clear, colourless, no field indicators (visual or olefactory) Microbial degradation rapid in aerobic environments and surface water (CCME, 2006) + 2- C4H8O2S + 6.5O2 4CO2 + 3H2O + 2H +SO4 Nutrients improve degradation times Low pH conditions inhibit degradation Typical degradation times: 2 to 4 days at 28°C and 8 to 12 days at 8°C (Green et al., 1998), average air temperatures during trials ranged from 6.9 to 14.1°C Groundwater and Soil Oxygen and nutrients (soil tilling, blowers) (Biogenie, 2006) Groundwater Activated Sludge Treatment System (WorleyParsons Komex, 2008) Oxidants (e.g., hydrogen peroxide) and/or UV light Mixed success (Barr Engineering, 2013; Gallegos et al., 2013; EBA, 2015) Peroxide and iron catalyst shown to be more effective than peroxide (Gallegos, 2013) No sulphate as by-product Site is an operating gas plant located in southern Alberta Constructed in 1960s Sulfolane investigation and monitoring since 1994 No active facilities Downgradient of active facilities Majority of plant waste stored here before the 1980s Potential materials disposed: alumina catalyst, filters (compressor, sulfinol, salt water, glycol, solvent receiver), zeolite, etc. Cells
    [Show full text]
  • Technical Datasheet: Udel® P-1700
    Udel® P-1700 Polysulfone Solvay Specialty Polymers www.ulprospector.com Technical Data Product Description Udel® P-1700 polysulfone (PSU) is a tough, rigid, high-strength thermoplastics suitable for continuous use up to 300°F (149°C). It is resistant to oxidation and hydrolysis and withstand prolonged exposure to high temperatures and repeated sterilization. Udel® P-1700 polysulfone is highly resistant to mineral acids, alkali and salt solutions. Resistance to detergents and hydrocarbon oils is good, but the resin may be attacked by polar solvents such as ketones, chlorinated hydrocarbons and aromatic hydrocarbons. These resins are also highly resistant to degradation by gamma or electron beam radiation. Electrical properties of Udel® P-1700 polysulfones are stable over a wide temperature range and after immersion in water or exposure to high humidity. The resins comply with FDA 21 CFR 177.1655 and may be used in articles intended for repeated use in contact with foods. Additionally, they are approved by the NSF, by the Department of Agriculture for contact with meat and poultry and by the 3-A Sanitary Standards of the Dairy Association. • Transparent: Udel® P-1700 CL 2611 CMP • Transparent: Udel® P-1700 NT 06 • Transparent: Udel® P-1700 NT 11 • Opaque Black : Udel® P-1700 BK 937 • Opaque White: Udel® P-1700 WH 6417 • Opaque White: Udel® P-1700 WH 7407 • Opaque Gray: Udel® P-1700 GY 8057 General Material Status • Commercial: Active Literature 1 • Technical Datasheet UL Yellow Card 2 • E36098-231084 • Solvay Specialty Polymers Search for
    [Show full text]
  • G ( NOW T LSO )
    Oct. 21, 1969 D. M. E. 3,474,030 PREVENING SO RESIN FORMATION WITH A SULFOLANE Filed Oct. 9, 1967 f O O n S. NO WISO r W?? WA Q i? 1 a O r Q r C " ? l (? - 2 st e3 r g ( NOW T LSO ) SP & y (T)w 5 > < n Q - ( c O cy P O (? CO w o (f) 7: (s OW&WS ) O) O 3. R k N i 1 ? k y CO s m Yn C - CO s aa ( SS 2 Ele=E c l N 5: N NOLOW X3 NBA OS c INVENTOR. D. M. LTTLE BY y C Year A 77OAPAWAYS 3,474,030 United States Patent Office Patented Oct. 21, 1969 2 A further object of this invention is to minimize the 3,474,030 formation of resinous deposits during the operation of PREVENTING SO, RESIN FORMATION a unit employing SO2 and to provide a practical method WITH A SULFOLANE Donald M. Little, Bartlesville, Okla., assignor to Phillips for removing resinous materials inadvertently formed dur Petroleum Company, a corporation of Delaware 5 ing operation of the process. Filed Oct. 9, 1967, Ser. No. 673,607 Other objects, aspects as well as the several advantages Int. C. C10g 21/10, 21/22 of the invention will be apparent to those skilled in the U.S. C. 208-338 8 Claims art upon reading the specification, drawing, and the ap pended claims. O Summary of the invention ABSTRACT OF THE DISCLOSURE According to the invention, I have found that resinous Dissolution of resinous materials formed from SO2 and materials formed from SO2 and unsaturated materials unsaturated materials coming in contact with SO2, for ex contained in hydrocarbon oils coming in contact with SO ample, during the SO2 solvent extraction of hydrocarbon can be dissolved by contacting with at least one sulfolane.
    [Show full text]
  • Studies on Radiation Crosslinking of Polysulfone
    JP0050427 JAERI-Conf 2000-001 Studies on Radiation Crosslinking of Polysulfone Xiaoguang Zhong Jiazhen Sun Changchun Institute of Applied Chemistry Chinese Academy of Sciences Changchun 130022, China Polysulfone is a kind of high temperature-resistance and radiation-resistance engineering plastic. The chemical structure is as follows: Brown (1), Lyon (2), Sasuga (3), et al have already studied its radiation effect. We studied CH3 radiation crosslinking effect of polysulfone by using of XPS, ESR, and CG methods and got some new results. Results and Discussions 1. Study radiation crosslinking of polysulfone by XPS method Because of conjugate system of benzene ring, polymer material which contains of benzene ring will appear shake-up peak in XPS spectra. Wanxi Zhang (4) shows that during radiation crosslinking of polystyrene increases with radiation dose and the intensity of shake-up peak decreases gradually with increase of radiation dose and crosslinking degree. This suggests that radiation crosslinking destroyed conjugate system of benzene ring. During radiation crosslinking of polysulfone, we find rules of shake-up peaks in the XPS spectra are different at different radiation crosslinking temperature. At lower temperature the intensity of shake-up peak decreases with the increase of radiation dose. This rule is similar to that of radiation crosslinking of polystyrene. The results are shown in Fig. 1. 183- JAERI-Conf 2000-001 Fig. 1. The spectra of radiation crosslinking of polysulfone at 70"C Comparing with radiation crosslinking at lower temperature, the intensity of shake-up peak increases with radiation dose when radiation crosslinking reaction takes place at temperature above glass transition temperature of polysulfone.
    [Show full text]
  • US3636140.Pdf
    Jan. 18, 1972 A. F. INGULLI ETA 3,636,140 THERMOPLASTIC RESIN BLEND OF POLY SULFONE WITH ABS Filed Aug. 4, 1969 5. Sheets-Sheet, 2. R O /O 20 30 40 0 60 22 80 20 M22 (7, AOA. Yuo/MAOM/A /W AA S adze wa /MVA MV7 OAS Air 7- 4. a Zafa AA A. MM/G/ZZ / A/a. Mary A. at 7A air 2- 9% agew, Jan. 18, 1972 A. F. NGULL ET All- 3,636,140 "I HERMOPLASTIC RESIN BLEND OF POLYSULFONE WITH ABS Filed Aug. 4, 1969 5. Sheets-Sheet 3 S | | | | | | \ / | | | | |\ 1 \ | | | | | | | | \ | | | | | | | N TTTTTTTT O 3O 20 O SO 70 so 90 /OO 7. AozYuva /owa w Aaj azawo 2g z 7-5 MM/a M72A S. AAAAAA M. MMMGO/4 AM AyAAMA 1 A... a A. JAA larus 9.4 AG AW 7 Jan. 18, 1972 A. F. NGULL FT All- 3,636,140 TERMOPLASTIC RESIN BLEND OF POLYSULFONE WITH ABS Filed Aug. 4, 1969 5 Sheets-Sheet 4. 24.0 -- -T 22.ol | | | || 20.0 I Y Mas t SR I W. n w /4.0 | -- N - S v 2.0 HI N | n N S s S. v O /O 20 30 10 60 60 70 &0 70 /00 7./oz ruz/z/-owa //v4 as aza/v4 MM VAM/OA 27zz7 a AAAMAA A. MM6t/44/ A/AMMA)1 A. az Zafa 9ers /.4- a 47AM/7 Jan. 18, 1972 A. F. NGULL ET All- 3,636,140 THERMOPLASTIC RESIN BLEND OF POLYSULFONE WITH ABS Filed Aug. 4, 1969 5 Sheets-Sheet 5 JO J00 290 28 O 270 28 O 25 O 24 O 2.3 O O O 20 JO 40 50 60 70 8 O 3 O LOO % AOZyura/4 MoM2 //v 44, aza/V2 , , , .
    [Show full text]
  • High Performance Reactive Blends Composed of Poly(P-Phenylene Sulfide)
    Polymer Journal (2011) 43, 991–999 & The Society of Polymer Science, Japan (SPSJ) All rights reserved 0032-3896/11 $32.00 www.nature.com/pj ORIGINAL ARTICLE High performance reactive blends composed of poly(p-phenylene sulfide) and ethylene copolymers Hideko T Oyama, Mayu Matsushita and Motonobu Furuta Poly(p-phenylene sulfide) (PPS) is a high performance polymer that has superior chemical resistance and heat stability, but its brittleness is a serious drawback for applications. The objective of this work is to improve the physical properties of PPS by incorporating a small amount of either poly(ethylene-ran-methylacrylate–ran-glycidyl methacrylate) (EMA–GMA) or poly(ethylene- ran-glycidyl methacrylate)-graft-poly(methyl methacrylate) (EGMA-g-PMMA) by melt mixing under a high shear rate. It was demonstrated that the chemical reaction between PPS and EMA–GMA (or EGMA-g-PMMA) proceeded efficiently at the interface and that the domains of EMA–GMA (or EGMA-g-PMMA) were finely dispersed in the PSS matrix with size of ca 0.1–0.3 lm. The resultant copolymers formed at the interface contributed to a decrease in the interfacial tension and an increase in the interfacial adhesion so that the obtained PPS/EMA–GMA blends (or PPS/EGMA-g-PMMA blends) showed excellent mechanical properties, at the same time retaining high thermal stability. Polymer Journal (2011) 43, 991–999; doi:10.1038/pj.2011.106; published online 19 October 2011 Keywords: blend; copolymer; interface; poly(ethylene-ran-glycidyl methacrylate); poly(phenylene sulfide) INTRODUCTION ties are not reported in the same paper, it was found that the Poly(phenylene sulfide) (PPS) is a high performance super-engineer- activation energy of crystallization of PPS increases by blending ing plastic with high thermal stability (over 150 1C), excellent chemical with PES and that the equilibrium melting temperature decreases resistance (no solvents under 200 1C), good electrical and electronic linearly with increase of the PES content.
    [Show full text]
  • LSR Material Chart and REACH Statement
    LSR Material Chart and REACH Statement Article Component Part Material Abbreviation Storage Pouch Polyethylene PE Compact Case Case Polypropylene PP Partition wall Acrylonitrile Butadiene Styrene ABS Display Case Case Polypropylene PP Window Methyl Methacrylate Acrylonitrile Butadiene Styrene MABS Tray Acrylonitrile Butadiene Styrene ABS Lock Polyamide PA Bag Bag Silicone rubber SI Valve Connector Polysulfone PSU O-Ring Fluorelastomer VITON Patient Valve Upper Housing Polysulfone PSU Patient side Housing Polysulfone PSU Lip Valve Silicone rubber SI Disk Membrane Silicone rubber SI Stem Polyphenylsulfone PPSU Cap Polysulfone PSU Pressure Relief Valve Spring Stainless steel Seal Silicone rubber SI Intake Valve Outer part Polysulfone PSU Inner part Polysulfone PSU Cap Polysulfone PSU Flap Valve Silicone rubber SI Intake Membrane Silicone rubber SI O² Reservoir Bag Reservoir Bag Polyvinyl chloride PVC Coupling for Bag Poly Carbonate PC Masks Masks No.00-0/1-2 Silicone rubber SI No.3-4, 4-5+ Silicone rubber SI No.0-1-2 Silicone rubber SI Article Component Part Material Abbreviation Mask Cover Polysulfone PSU Lock Clip Stainless steel Head Strap w/Ring Strap Thermoplastic Elastomer TPE Attachment Ring Polysulfone PSU Expiration Diverter Housing Polysulfone PSU Center gasket Silicone rubber SI External gasket Silicone rubber SI Extension Tube Tube Silicone rubber SI Coupling Polysulfone PSU Manometer Polysulfone PSU Connector Hanging Loop Silicone rubber SI Wall Mount Acrylonitrile Butadiene Styrene ABS Wall Bracket PolyOxyMethylene POM Laerdal Statement for REACH Regulation EC No 1907/2006 Substances of Very High Concern are not used in concentrations above 0.1% (w/w) in the production of all models of the Laerdal Silicone Resuscitator.
    [Show full text]
  • Polysulfone PSU1000 Datasheet
    Quality Plastics Since 1936 POLYSULFONE - PSU1000 Characteristics * Broad Temperature Range Capability - Hot Water and Steam Performance to 300º F (150 C) * Good Thermal and Electrical Insulation Characteristics * Hydrolysis Resistant * Radiation Stability * Low Ionic Impurity Description PSU 1000 Polysulfone is an amber semi-transparent, heat resistant, high performance engineering thermoplastic. It offers excellent mechanical, electrical and improved chemical resistance properties relative to polycarbonate. Polysulfone's properties remain relatively consistent over a broad temperature range, from -150º to 300º F (-100º to 150º C). PSU Polysulfone offers high chemical resistance to acidic and salt solutions, and good resistance to detergents, hot water and steam. In addition, polysulfone has excellent radiation stability and offers low ionic impurity levels. PSU 1000 Polysulfone often replaces polycarbonate when higher temperatures, improved chemical resistance or autoclavability is required. It is commonly used for analytical instrumentation, medical devices and semiconductor process equipment components. Forms Available ROD .250 to 6.00 " diameter, Lengths to 12 feet TUBE Custom produced as requested PLATE .250" to 3.000" thick, Widths to 24", Lengths to 48" COLOR Amber Typical Property Values Polysulfone MECHANICAL @ 73ºF PSU-1000 Specific Gravity 1.24 Tensile Strength psi 10,200 Tensile Modulus of Elasticity psi 390,000 Tensile Elongation ( at Break ) % 30 Flexural Strength psi 15,000 Flexural Modulus of Elasticity psi 400,000 Shear Strength psi 9,000 Compressive Strength, 10% Deformation psi 13,000 Compressive Modulus of Elasticity psi 375,000 Rockwell Hardness M Scale 82 Izod Impact Strength, Notched ft-lbs/in. of notch 1.30 Coefficient of Friction, Dynamic ( Dry vs. Steel ) Limiting PV ( 4 :1 Safety Factor Applied ) ft.lbs/in.² min Wear Factor in³-min/ft.lbs.
    [Show full text]
  • Sulfolane: Magic Extractor Or Bad Actor? Pilot-Scale Study on Solvent Corrosion Potential
    sustainability Review Sulfolane: Magic Extractor or Bad Actor? Pilot-Scale Study on Solvent Corrosion Potential Andrzej Bak 1,* , Violetta Kozik 1, Paulina Dybal 1, Slawomir Kus 2, Aleksandra Swietlicka 1 and Josef Jampilek 3,* 1 Department of Synthesis Chemistry, Faculty of Mathematics, Physics and Chemistry, University of Silesia, Szkolna 9, 40007 Katowice, Poland; [email protected] (V.K.); [email protected] (P.D.); [email protected] (A.S.) 2 Honeywell Process Solutions, 11201 Greens Crossing Blvd, Suite 700 Houston, TX 77067, USA; [email protected] 3 Department of Pharmaceutical Chemistry, Faculty of Pharmacy, Comenius University, Odbojarov 10, 83232 Bratislava, Slovakia * Correspondence: [email protected] (A.B.); [email protected] (J.J.); Tel.: +48-32-359-1197 (A.B.) Received: 17 September 2018; Accepted: 11 October 2018; Published: 14 October 2018 Abstract: The sulfur-containing derivatives and their metabolites, regarded as ‘old devils of green’ chemistry, constitute a relevant class of air/water/soil contaminants in over-polluted world. In fact, some industrially-engineered solvents have become environmentally unfavorable. An attractive alternative to commonly used industrial liquids is sulfolane (C4H8SO2), an anthropogenic medium. The main objective of this paper is the comprehensive review focusing mainly on the state-of-the-art aspects of the sulfolane synthesis, application of sulfolane as an extractive solvent due to its ‘unique’ physicochemical properties as well as the potential of sulfolane to cause equipment corrosion and subsequent spills. The potential risk for groundwater contamination, danger for human health and ways of sulfolane biodegradation were briefly reviewed as well. Interestingly, the analysis performed on data stored in the Reaxys database revealed an alternating tendency of waxing and waning interest in sulfolane during the space of the last fifty years.
    [Show full text]