Tailored Platform Bed ASSEMBLY INSTRUCTIONS

BED COMPONENTS

ITEM QUANTITY NOTES: A Metal Corners 4 • Open all hardware packets before B Metal Side Rail 2 proceeding. C Metal End Rail 2 • Two people are needed for assembly. D Corner Leg 4 • Additional support legs are in wooden plank roll box. E Center Support Rail 1 F Center Support Leg 1 YOU WILL NEED: G Upholstered Side Rail 4 • Flat head screwdriver H Upholstered Foot Rail 4 I Wooden Slat Roll 1

I Wooden Slat Roll (located in headboard box)

*Images may vary from actual product

LIMITED WARRANTY All our items are returnable within 30 days and guaranteed against defects in construction for one year. NEED SOME HELP? For any questions contact us via your preferred method. Mon-Fri 9AM-9PM: Call 909-323-0016 OR E-Mail [email protected] Tailored Platform Bed ASSEMBLY INSTRUCTIONS

BED HARDWARE

1/4” 1/4” 3/4” X 5/16” 3/4” BOLTS NUTS BOLTS WASHER x 10 x 14 x 4 x 4

1” X 1/4” 3/4” 1” X 5/16” 1 X 1/4” BOLTS WASHER BOLT WASHER x 5 x 1 x 6 x 6

SMALLER LARGER WRENCH L WRENCH L WRENCH x 1 x 1 x 1

3/4” L BRACKET SCREW x 2 x 8 (optional) (optional)

STEP 1 - BUILDING THE METAL BED FRAME

1. Place (A) metal corners in a rectangular shape roughly the size of your mattress.

2. Lay (B) metal side rails and (C) metal end rails into (A) metal corners to create the shape of your bed frame. Snap into place.

3. Secure (B) metal side rails and (C) metal end rails to (A) metal corners using 1/4” bolts and 1/4” nuts. Tighten using small L Wrench and the wrench.

Note: 1/4” nuts should be on the inside of the frame.

4. Carefully attach (D) corner legs underneath (A) metal corners using 3/4” x 5/16” bolts and 3/4” washers. Tighten using larger L wrench. Tailored Platform Bed ASSEMBLY INSTRUCTIONS

STEP 2 - CENTER SUPPORT SYSTEM

1. Align holes of (E) center support rail with holes on (B) metal side rails. Attach using 1/4” bolts and 1/4” nuts. Tighten using the smaller L wrench and the wrench.

Note: (E) center support rail attaches underneath (B) metal side rails.

2. Attach (F) center support legs to (E) center support rail using 1” x 1/4” bolts and 3/4” washer. Tighten using smaller L wrench.

3.Carefully place the (I) wooden slat roll onto the bed frame. Attach using 1” x 1/4” bolts and 1/4” nuts. Tighten with smaller L wrench and the wrench.

Note: The black band that holds the slats together should face the floor. Tailored Platform Bed ASSEMBLY INSTRUCTIONS

STEP 3 - ATTACHING THE UPHOLSTERED RAILS

1. Loosely attach (G, H) upholstered rails to bed frame using 1” x 5/16” bolts and 1 1/4” washers.

Note: If (G) upholstered side rails have an additional hole, make sure the hole faces upwards and away from the (H) upholstered foot rail.

2. Push (G) upholstered side rails toward (H) upholstered foot rail to eliminate any gaps. Tighten (G) upholstered side rails first, then(H) upholstered foot rail using flat head screwdriver.

3. (OPTIONAL) To reinforce stability of (G, H) upholstered rails, use a phillips screwdriver to attach L brackets using 3/4” screw.

Note: this requires screwing 3/4” screws directly into the upholstered side rail. Headboard ASSEMBLY INSTRUCTIONS

HEADBOARD COMPONENTS

(A) HEADBOARD Note: actual headboard may look different than illustration.

(B) HEADBOARD LEGS x 2

HARDWARE INCLUDED:

5/8” X 5/16” 1 1/4” 1” X 1/4” 1/4” BOLTS WASHER BOLTS NUTS x 4 x 12 x 4 x 4

Note: You will need a flat head screwdriver and a wrench for assembly.

STEP 1

1. Place (A) headboard face down on a flat surface. Place B)( headboard legs on the back of (A) headboard, aligning the slots of the legs with the holes of the headboard.

Note: Make sure the “Out” sticker on each (B) headboard leg is facing the correct way.

2. Attach (B) headboard legs to (A) headboard using 5/8” x 5/16” bolts and 1 1/4” washers. Tighten with a flat head screwdriver. Headboard ASSEMBLY INSTRUCTIONS

STEP 2

Attach the assembled headboard to your bedframe using 1 x 1/4” bolts, 1 1/4” washers and 1/4” nuts. Tighten with a flat head screwdriver and wrench.

Note: The height of your headboard can be adjusted by loosening the (H1) bolts and shifting the (A) headboard up or down.