DOCSLIB.ORG

Quadrac Internally Triggered Triacs (4 a to 15 A)

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Quadrac Internally Triggered Triacs (4 a to 15 A) Thyristor Product Catalog Teccor Electronics 1800 Hurd Drive Irving, Texas 75038 United States of America Phone: +1 972-580-7777 Fax: +1 972-550-1309 Website: http://www.teccor.com E-mail: [email protected] ©2002 Teccor Electronics i http://www.teccor.com Thyristor Product Catalog +1 972-580-7777 Downloaded from Elcodis.com electronic components distributor Teccor Electronics reserves the right to make changes at any time in order to improve designs and to supply the best products possible. The information in this catalog has been carefully checked and is believed to be accurate and reliable; however, no liability of any type shall be incurred by Teccor for the use of the circuits or devices described in this publication. Furthermore, no license of any patent rights is implied or given to any purchaser. Teccor Electronics is the proprietor of the QUADRAC® trademark. is a registered trademark of Underwriters Laborato- ries, Inc. All other brand names may be trademarks of their respective companies. To conserve space in this catalog, the trademark sign (®) is omitted. http://www.teccor.com ii ©2002 Teccor Electronics +1 972-580-7777 Thyristor Product Catalog Downloaded from Elcodis.com electronic components distributor Contents Product Selection Guide Product Descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - vi Circuit Requirement Diagram - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - vii Product Packages - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - viii Description of Part Numbers- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - x Quality and Reliability Assurance - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - xii Standard Terms and Conditions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - xiv Data Sheets V-I Characteristics of Thyristor Devices - - - - - - - - - - - - - - - - - - - - - - - - E0-2 Electrical Parameter Terminology - - - - - - - - - - - - - - - - - - - - - - - - - - - - E0-3 Electrical Specifications Sensitive Triacs- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - E1 Triacs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - E2 QUADRACs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - E3 Alternistor Triacs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - E4 Sensitive SCRs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - E5 SCRs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - E6 Rectifiers - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - E7 Diacs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - E8 SIDAC - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - E9 Mechanical Specifications Package Dimensions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - M1 Lead Form Dimensions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - M2 Packing Options - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - M3 Application Notes Fundamental Characteristics of Thyristors - - - - - - - - - - - - - - - - - - - AN1001 Gating, Latching, and Holding of SCRs and Triacs - - - - - - - - - - - - - AN1002 Phase Control Using Thyristors- - - - - - - - - - - - - - - - - - - - - - - - - - - AN1003 Mounting and Handling of Semiconductor Devices - - - - - - - - - - - - - AN1004 Surface Mount Soldering Recommendations - - - - - - - - - - - - - - - - - AN1005 Testing Teccor Semiconductor Devices Using Curve Tracers - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - AN1006 Thyristors Used As AC Static Switches and Relays - - - - - - - - - - - - AN1007 Explanation of Maximum Ratings and Characteristics for Thyristors - AN1008 Miscellaneous Design Tips and Facts - - - - - - - - - - - - - - - - - - - - - - AN1009 Thyristors for Ignition of Fluorescent Lamps- - - - - - - - - - - - - - - - - - AN1010 Appendix Cross Reference Guide - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A1 Part Numbers Index- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A27 ©2002 Teccor Electronics iii http://www.teccor.com Thyristor Product Catalog +1 972-580-7777 Downloaded from Elcodis.com electronic components distributor http://www.teccor.com iv ©2002 Teccor Electronics +1 972-580-7777 Thyristor Product Catalog Downloaded from Elcodis.com electronic components distributor Product Selection Guide Product Descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P 2 Circuit Requirement Diagram - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P 3 Product Packages - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P 4 Description of Part Numbers- - - - - - - - - - - - - - - - - - - - - - - - - - - - - P 6 Quality and Reliability Assurance - - - - - - - - - - - - - - - - - - - - - - - - - P 8 Standard Terms and Conditions - - - - - - - - - - - - - - - - - - - - - - - - - P 10 ©2002 Teccor Electronics P - 1 http://www.teccor.com Thyristor Product Catalog +1 972-580-7777 Downloaded from Elcodis.com electronic components distributor Product Descriptions Thyristors Sensitive SCRs A thyristor is any semiconductor switch with a bi-stable action Teccor's sensitive gate SCRs are silicon-controlled rectifiers repre- depending on p-n-p-n regenerative feedback. Thyristors are nor- senting the best in design, performance, and packaging techniques mally two- or three-terminal devices for either unidirectional or bi- for low- and medium-current applications. directional circuit configurations. Thyristors can have many forms, Anode currents of 0.8 A to 10 A rms can be controlled by sensitive but they have certain commonalities. All thyristors are solid state gate SCRs with gate drive currents ranging from 12 µA to 500 µA. switches that are normally open circuits (very high impedance), Sensitive gate SCRs are ideally suited for interfacing to integrated capable of withstanding rated blocking/off-state voltage until trig- circuits or in applications where high current load requirements and gered to on state. When triggered to on state, thyristors become a limited gate drive current capabilities exist. Examples include igni- low-impedance current path until principle current either stops or tion circuits, motor controls, and DC latching for alarms in smoke drops below a minimum holding level. After a thyristor is triggered detectors. Sensitive gate SCRs are available in voltage ratings to to on-state condition, the trigger current can be removed without 600 V ac. turning off the device. Thyristors are used to control the flow of electrical currents in applications including: • Home appliances (lighting, heating, temperature control, alarm SCRs activation, fan speed) Teccor's SCR products are half-wave, silicon-controlled rectifiers • Electrical tools (for controlled actions such as motor speed, sta- that represent the state of the art in design and performance. pling event, battery charging) Load current capabilities range from 1 A to 70 A rms, and voltages • Outdoor equipment (water sprinklers, gas engine ignition, elec- from 200 V to 1000 V may be specified to meet a variety of appli- tronic displays, area lighting, sports equipment, physical fitness) cation needs. Because of its unidirectional switching capability, the SCR is used in circuits where high surge currents or latching action is required. Sensitive Triacs It may also be used for half-wave-type circuits where gate-con- Teccor's sensitive gate triacs are AC bidirectional silicon trolled rectification action is required. Applications include crow- switches that provide guaranteed gate trigger current levels in bars in power supplies, camera flash units, smoke alarms, motor Quadrants I, II, III, and IV. Interfacing to microprocessors or other controls, battery chargers, and engine ignition. equipment with single polarity gate triggering is made possible with Surge current ratings are available from 30 A in the TO-92 packag- sensitive gate triacs. Gate triggering currents of 3 mA, 5 mA, ing to 950 A in the TO-218X package. 10 mA, or 20 mA may be specified. Sensitive gate triacs are capable of controlling AC load currents Rectifiers from 0.8 A to 8 A rms and can withstand operating voltages from 200 V to 600 V. Teccor manufactures 15 A to 25 A rms rectifiers with voltages rated from 200 V to 1000 V. Due to the electrically isolated TO-220 package, these rectifiers may be used in common anode or com- Triacs mon cathode circuits using only one part type, thereby simplifying Teccor's triac products are bidirectional AC switches, capable of stock requirements. controlling loads from 0.8 A to 35 A rms with 10 mA, 25 mA, and 50 mA IGT in operating Quadrants I, II and III. Diacs Triacs are useful in full-wave AC applications to control AC power either through full-cycle switching or phase control of current to the Diacs are trigger devices used in phase control circuits to provide load element. These triacs are rated to block voltage in the “OFF” gate pulses to a triac or SCR. They are voltage-triggered bidirec- condition from 200 V minimum with selected products capable of tional silicon devices housed in DO-35 glass axial lead packages 1000 V operation. Typical applications include motor speed con- and
Load more

Recommended publications
  • TRIAC Overvoltage Protection Using a Transil™
    AN1966 Application note TRIAC overvoltage protection using a Transil™ Introduction In most of their applications, TRIACs are directly exposed to overvoltages coming from the mains, as described in IEC 61000-4-5 or IEC 61000-4-4 standards. When TRIACs are used to drive resistive loads (ex: temperature regulation), it is essential to provide them with efficient overvoltage protection to prevent any turn-on in breakover mode that could lead to device damage. A traditional method to clamp the voltage is to use a varistor in parallel across the TRIAC. But with high power loads (a few kW), the current through the varistor is very high in case of surge voltages (a few hundred amperes). The varistor is then not efficient enough, due to its dynamic resistor, to limit the TRIAC voltage to a low value. We present here a solution that can be used for these kinds of applications and also for all applications where TRIAC voltage protection is required. It should be noted that the overvoltages could also come from the overvoltages that appear at device turn-off due to the TRIAC holding current. This phenomenon occurs mainly with TRIACs controlling low rms current (15-50 mA), high inductive loads like valves. For more information about such behavior, please refer to AN1172. Contents 1 Why overvoltage protection is required . 2 2 Overvoltage protection solution . 3 3 Transil choice for efficient TRIAC voltage protection . 6 3.1 Normal operation: check VRM voltage . 6 3.2 Surge voltage clamping: check max VCL voltage . 6 4 Experimental validation example . 8 5 Conclusion .
    [Show full text]
  • Triac Control with a Microcontroller Powered from a Positive Supply
    AN440 Application note Triac control with a microcontroller powered from a positive supply Introduction This application note explains how to implement a control circuit to drive an AC switch (Triac, ACS or ACST) in case the microcontroller unit (MCU) is supplied with a positive voltage. The driving circuit will also depends on the kind of Triac used and also if other supplies (positive or negative) are available. We also deal about the case of insulated or non-insulated supplies. It is recommended to refer to AN4564 which explains why positive supplies are usually implemented and how simple solutions can be implemented to get a negative supply. Refer also to AN3168 for information about AC switch control circuits in case the microcontroller is supplied with a negative power supply. AN440 - Rev 4 - March 2020 www.st.com For further information contact your local STMicroelectronics sales office. AN440 Positive supply defintion and AC switch triggering quadrants 1 Positive supply defintion and AC switch triggering quadrants 1.1 Positive power supply A positive power supply is a supply where its reference level (VSS) is connected to the mains (line or neutral). The VDD level is then above the mains terminal as shown in Figure 1. If the supply is a 5 V power supply, then VDD is 5 V above the mains reference. This is why such a supply is called a positive supply (compared to a negative supply as shown in AN3168). Figure 1. Positive supply basic schematic 1.2 AC switch triggering quadrants To switch-on an AC switch, like any bipolar device, a gate current must be applied between its gate pin (G) and its drive reference terminal (refer also to AN3168).
    [Show full text]
  • An Application of TRIAC to Capacitor Motor for Hermetic Compressor K
    Purdue University Purdue e-Pubs International Compressor Engineering Conference School of Mechanical Engineering 1984 An Application of TRIAC to Capacitor Motor for Hermetic Compressor K. Nakane Y. Tozaki H. Sakamoto Follow this and additional works at: https://docs.lib.purdue.edu/icec Nakane, K.; Tozaki, Y.; and Sakamoto, H., "An Application of TRIAC to Capacitor Motor for Hermetic Compressor" (1984). International Compressor Engineering Conference. Paper 449. https://docs.lib.purdue.edu/icec/449 This document has been made available through Purdue e-Pubs, a service of the Purdue University Libraries. Please contact [email protected] for additional information. Complete proceedings may be acquired in print and on CD-ROM directly from the Ray W. Herrick Laboratories at https://engineering.purdue.edu/ Herrick/Events/orderlit.html AN APPLICA'l'ION OF 'l'RIAC TO CAPACI'l'OR 1-10'l'OR FOR lll~Rt~IC'riC COMPRSSO!l Ka.zuhiro Nakane, Yasuhiro To?.nki,. Ilirota.ka Sakamoto Shizuoka. Worlw, Mitsubishi Electri.c Corporation Shizuoka City , Ja.pan ABSTRACT oncy and output rati.ngo are 100 V ,50/60 J!v. and 100 11. It is a. 1mi 1 t-in motor for the rotary type This paper refers to a.n n.pplication study of 'l'lUAC hermetic compressor shown in Ji'ie;. 2. 'l'hore are to PSC motor for thft hermetic compessor. It is three types of the wirings of the starting device 1-1ell lcnown that 'l'HIAC rlel nys pharJa ane,le of the for thifl motor,as shown i.n lcig, 3. A shows CSR current and has no losses if it is consider(\ as moto:r,n shows P'l'C asoist CSR motor and C sho~1s ideal flwitch.
    [Show full text]
  • Thyristors & Triacs
    APPLICATION NOTE Thyristors & Triacs - Ten Golden Rules for Success In Your Application. This Technical Publication aims to provide an threshold current IGT, within a very short time known as interesting, descriptive and practical introduction to the the gate-controlled turn-on time, tgt, the load current can golden rules that should be followed in the successful flow from ’a’ to ’k’. If the gate current consists of a very use of thyristors and triacs in power control applications. narrow pulse, say less than 1µs, its peak level will have to increase for progressively narrower pulse widths to Thyristor guarantee triggering. A thyristor is a controlled rectifier where the When the load current reaches the thyristor’s latching unidirectional current flow from anode to cathode is current IL, load current flow will be maintained even after initiated by a small signal current from gate to cathode. removal of the gate current. As long as adequate load current continues to flow, the thyristor will continue to akconduct without the gate current. It is said to be latched ON. Note that the VGT,IGT and IL specifications given in data g are at 25 ˚C. These parameters will increase at lower temperatures, so the drive circuit must provide adequate Fig. 1. Thyristor. voltage and current amplitude and duration for the The thyristor’s operating characteristic is shown in lowest expected operating temperature. Fig. 2. Rule 1. To turn a thyristor (or triac) ON, a gate current On-state ≥ Forward IGT must be applied until the load current is current characteristic ≥ IL. This condition must be met at the lowest expected operating temperature.
    [Show full text]
  • How to Implement a SCR Or a Triac in a Hybride Relay Application
    AN4993 Application note How to implement an SCR or a Triac in hybrid relay applications Introduction This document gives some key information about the design of the solid-state silicon AC switch stage of a hybrid relay, which can drive resistive, capacitive or inductive AC loads, such as: heater resistors, motors for industry, power tools or appliance applications. Section 1 describes the hybrid relay principle. Circuit and functional diagram is the first topic to be handled followed by its advantages and drawbacks and finally the main targeted applications are listed. Section 2 specifies different ways to drive the AC switch implemented on the hybrid relay circuit. Section 3 provides some design tips to pass electromagnetic compatibility standards, especially to reduce EMI noise. March 2017 DocID030191 Rev 1 1/23 www.st.com Contents AN4993 Contents 1 Hybrid relay ...................................................................................... 5 1.1 General schematic ............................................................................ 5 1.2 Advantages and drawbacks .............................................................. 6 1.3 Applications ....................................................................................... 7 1.3.1 Water and room heaters ..................................................................... 7 1.3.2 Home automation smart plug ............................................................. 7 1.3.3 Inrush limiter for power supply ..........................................................
    [Show full text]
  • Issues, Models and Solutions for Triac Modulated Phase Dimming of LED Lamps
    Issues, Models and Solutions for Triac Modulated Phase Dimming of LED Lamps Dustin Rand (Raytheon), Brad Lehman* (Northeastern University), Anatoly Shteynberg (Exclara, Inc.) *Dept. ECE; Northeastern University; Boston, MA 02115; [email protected] Abstract - This paper discusses the difficulties in dimming Edison metric tons of carbon emission, as well as alleviate the need of socket LED lamps directly from residential phase modulated more than 40 1000MW power stations [9,10]. dimmer switches. In order to explain these difficulties PSpice Dimmers models for the dimmers are proposed that necessarily include Residential dimmers are designed to meet the needs of diac characteristics to improve accuracy. A method to dim the homeowners and architects in both style and function. LEDs from the residential dimmers is discussed. Commercial companies offer a complete line of residential dimmers with an amazing array of colors that coordinate with the most popular interior colors and finishes. Commercial I. INTRODUCTION: LED LIGHTING - THE NEXT dimmers and dimming systems are designed to meet the TECHNOLOGICAL REVOLUTION? requirements of architects and specifiers of commercial spaces such as hotels, restaurants, offices and warehouses. Within the last few years, new LED materials and What is a Phase Modulated Dimmer? improved production processes have resulted in bright LEDs Incandescent bulbs primarily utilize phase modulating in colors throughout the visible spectrum with efficacies dimming through triac switches to control the power sent to greater than incandescent lamps [1,2]. In fact, recent the bulb. Dimming fluorescent lighting is possible by technological breakthroughs [3-7] in the high brightness retrofitting the lighting switches/infrastructure with electronic “White Light” LEDs have experts predicting that the “bright or other dimming ballasts.
    [Show full text]
  • Questions for Electronics
    www.YoYoBrain.com - Accelerators for Memory and Learning Questions for electronics Category: Default - (192 questions) What electronic device is a breakover diode diac made to trigger triacs in phase-controlled circuits 3 basic options for converting single phase to static, rotary, and electronic 3 phase power Define: static phase converter simplest/lowest cost option for converting single to 3 phase electricity Nothing more than a capacitor and a potential relay comprising a starter circuit Define: rotary phase converter consists of a 3-phase motor and some way of starting it, be it a rope and pulley or a well-designed static converter automatic start circuit converts single phase to 3 phase electricity Define: variable frequency drive a box of solid-state electronics that convert 3-phase 60 Hz AC to variable frequency 3-phase. Allows motors to be driven at different speeds Define: polarized plug a plug that must be plugged in correctly to reference line on ac plug or it will harm the equipment Define: Shockley diode special purpose diode with more 2 PN junctions (four-layer diode) uses a trigger voltage to switch the diode on What is the purpose of SSIFET transistors used in microwave frequency circuits Define: latching relay a relay where one control pulse closes the switch contacts and it remains closed until another signal tells it to release Define: component placement diagram used to show where components are layed out on circuit board Define: cold solder joints a rough and grainy solder joint; source of many problems on circuits
    [Show full text]
  • Teccor® Brand Thyristors Qxxxxltx Series
    Teccor® brand Thyristors 4 / 6 / 8 / 10 / 15 Amp Quadracs QxxxxLTx Series RoHS ® Description The Quadrac is an internally triggered Triac designed for AC switching and phase control applications. It is a Triac and DIAC in a single package, which saves user expense by eliminating the need for separate Triac and DIAC components. Standard type devices normally operate in Quadrants I & III triggered from AC line. Alternistor type Quadracs are used in circuits requiring high dv/dt capability. Features & Benefits Agency Approval • RoHS Compliant • Surge capability up to 200 A • Glass – passivated Agency Agency File Number junctions ® L Package : E71639 • Voltage capability up to 600 V Schematic Symbol Applications Excellent for AC switching and phase control applications such as lighting and heating. Typical applications are AC MT2 MT1 solid-state switches, light dimmers, power tools, home/ brown goods and white goods appliances. T Alternistor Quadracs (no snubber required) are used in applications with extremely inductive loads requiring highest commutation performance. Main Features Internally constructed isolated package is offered for ease Symbol Value Unit of heat sinking with highest isolation voltage. IT(RMS) 4 to 15 A VDRM / VRRM 400 to 600 V Additional Information DIAC VBO 33 to 43 V Datasheet Resources Samples © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/14/14 Teccor® brand Thyristors 4 / 6 / 8 / 10 / 15 Amp Quadracs Absolute Maximum Ratings Value Symbol Parameter Unit Qxx04LT Qxx10LT /
    [Show full text]
  • AN3168 Non-Insulated SCR / Triac Control Circuits
    AN3168 Application note Non-insulated SCR / Triac control circuits Introduction In alternating current applications the direct current power supply for low-voltage electronic devices (MCU, LEDs, optocouplers, Triacs and so on) can be provided using one of several different circuits. There are traditionally two major types of power supplies used in appliances, capacitive power supply and linear power supply using a step-down transformer. Today, designers are using more and more switches mode power supplies (SMPS) to achieve higher output current levels and especially lower standby power consumption. The power supply choice is a trade-off between several parameters. These are the cost, the required power, the output voltage level and polarity, the standby power consumption and the necessity or not of an electrical insulation between the mains and the low output DC voltage. This application note considers only non-insulated power supplies. After a brief description of the triggering quadrants and key parameters for SCR, Triac, ACS and ACST, the usual control circuits are described according to the output voltage polarity of the power supply. Finally, some examples of negative power supply circuits are introduced. March 2010 Doc ID 17193 Rev 1 1/20 www.st.com AN3168 Contents Contents 1 Triggering quadrants and key parameters . 3 2 Triggering circuits . 6 2.1 Two kind of power supply bias . 6 2.2 Gate resistor value definition . 6 2.3 SCR and Triac triggering circuit with a positive power supply . 7 2.4 Triac and ACS / ACST triggering circuit with negative power supply . 8 2.5 SCR triggering circuit with negative power supply .
    [Show full text]
  • Thyristors and Triacs Control Gate Trigger Circuits
    1 Lab no. 3 THYRISTORS AND TRIACS CONTROL GATE TRIGGER CIRCUITS 1. Introduction The thyristor is a power semiconductor device with the control terminal called grid or gate (G). The device name comes from the similarity of operation with the gas triode: thiratron transistor. Because the thyristors are mainly used in the controlled rectifier structures, the technical literature calls them as SCR (Semiconductor Controlled Rectifiers) devices. After the series manufacture start in 1957 until the ‘80s of the twentieth century the thyristor was the leader of power semiconductor devices with control electrode. Despite the fact that the thyristor is a half controlled device (through the gate terminal can be only turned on) this switch remains favourite in a wide range of applications because it is robust, can be easily controlled and can operates in high power structures at high voltages and currents with low power conduction losses. To operate, every thyristor require a drive (trigger, control) circuit that provides gate current pulses to induce the on-state. These pulses must have a certain amplitude and duration. The device remains latched in on-state until it is reverse biased. Thus, in forward biased conditions, after the turn-on process, the gate current can be interrupted. Thyristors can be found in various applications such as phase-controlled rectifiers, AC voltage variators, starters, static breakers, cycloconverters, etc. Depending on the requirements, are available on the market several types of thyristors: common thyristors (used in phase-controlled converters at low switching frequency, high voltages and currents), fast thyristors (with a small blocking time), optical thyristors (light-activated through optical fibers), etc.
    [Show full text]
  • Catalogo Tiristor
    Thyristor Product Catalog Teccor Electronics 1800 Hurd Drive Irving, Texas 75038 United States of America Phone: +1 972-580-7777 Fax: +1 972-550-1309 Website: http://www.teccor.com E-mail: [email protected] ©2002 Teccor Electronics i http://www.teccor.com Thyristor Product Catalog +1 972-580-7777 Teccor Electronics reserves the right to make changes at any time in order to improve designs and to supply the best products possible. The information in this catalog has been carefully checked and is believed to be accurate and reliable; however, no liability of any type shall be incurred by Teccor for the use of the circuits or devices described in this publication. Furthermore, no license of any patent rights is implied or given to any purchaser. Teccor Electronics is the proprietor of the QUADRAC® trademark. is a registered trademark of Underwriters Laborato- ries, Inc. All other brand names may be trademarks of their respective companies. To conserve space in this catalog, the trademark sign (®) is omitted. http://www.teccor.com ii ©2002 Teccor Electronics +1 972-580-7777 Thyristor Product Catalog Contents Product Selection Guide Product Descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - vi Circuit Requirement Diagram - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - vii Product Packages - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - viii Description of Part Numbers- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - x Quality
    [Show full text]
  • Thyristors Triacs Precautions For
    Common Item R07ZZ0011EJ0200 Thyristor・Triac (Previous: REJ27G0020-0100) Rev.2.00 Precautions for Use Aug.7.2019 Contents 1. Use of Thyristors ..................................................................................................................................... 2 (1) How to select current rating .............................................................................................................................. 2 (2) How to select withstanding voltage class........................................................................................................ 2 (3) Cautions on dv/dt ................................................................................................................................................ 3 (4) Cautions on di/dt ................................................................................................................................................. 3 (5) Measures to prevent false triggering ............................................................................................................... 3 2. Use of Triacs ........................................................................................................................................... 4 (1) How to select current rating .............................................................................................................................. 4 (2) How to select withstanding voltage class........................................................................................................ 4 (3)
    [Show full text]