DOCSLIB.ORG

Ladder Tray Installation Instructions Must Be Installed with Side Durarac Ford Transit Low/Med/High Roofs - 148” WB Ladder Tray Part #: DTC 0804-002 V1.0.10.24.18

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Ladder Tray Installation Instructions Must Be Installed with Side Durarac Ford Transit Low/Med/High Roofs - 148” WB Ladder Tray Part #: DTC 0804-002 V1.0.10.24.18 Ladder Tray Installation Instructions Must Be Installed With Side DuraRac Ford Transit Low/Med/High Roofs - 148” WB Ladder Tray Part #: DTC 0804-002 V1.0.10.24.18 1.877.335.2621 www.DEJANA.com IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED IN THE SPECIFIED ORDER TO ENSURE PROPER INSTALLATION AND MUST BE FOLLOWED IN ORDER TO MAINTAIN YOUR PRODUCT WARRANTY! CRITICAL INFORMATION PERTAINING TO USER AND/OR VEHICLE SAFETY IS DENOTED USING A CAUTION SIGN. SAFETY ITEMS MUST BE STRICTLY ADHERED TO IN ORDER TO ENSURE A SAFE WORKING ENVIRONMENT! WARNING THE USE OF DRILLS WITH INTEGRAL DRILL STOPS ALONG WITH PROPER INSPECTION FOR GAS TANK, GAS LINES, BRAKE LINES AND ELECTRICAL LINES PRIOR TO DRILLING ANY MOUNTING HOLES IS STRONGLY RECOMMENDED TO ENSURE THAT VEHICLE DAMAGE IS AVOIDED! THE USE OF AIR OR ELECTRIC IMPACT TOOLS FOR THE ASSEMBLY OF FASTENERS COULD CAUSE FASTENER FAILURE! THE USE OF NON‐STANDARD FASTENERS AND/OR DEVIATING FROM THE FASTENERS SPECIFIED IN THESE INSTRUCTIONS MAY VOID YOUR PRODUCT WARRANTY! ALL DRILLED HOLES IN THE VEHICLES SHOULD HAVE THE RAW METAL EDGES SEALED WITH A SELF‐ETCHING PRIMER TO RESIST CORROSION AND POTENTIAL FASTENER POINT FAILURE! 1.877.335.2621 www.DEJANA.com Ladder Tray Installation Instructions – TOOL LIST Safety glasses MUST be worn at all times! TOOLS Drill Drill Bits Drill Stop Ratchet Wrench 5/16”, 7/16”, 11/32” 1/2” Drill 10” Drift Punch Box End Wrench Rubber Mallet/ Steel Hammer 7/16”, 1/2” Socket; (Used in aligning bolt 7/16”, 1/2”, 9/16” T45, T30, T27 TORX Bit holes) with Misc. Extensions RECOMMENDED TOOLS: Inch-pound Torque Wrench Impact Gun Leveling Gauge 1.877.335.2621 www.DEJANA.com Ladder Tray Installation Instructions Hardware: FAS 37708 FAS 10051-12025 FAS 33078 FAS 0195543 FAS 0197057 FAS 0195544 ACORN NUT, T27 TORX HEAD FLAT WASHER, T30 TORX HEAD 1/4”-20 T30 TORX HEAD 1/4”-20 SCREW 1/4”-20 X 1/4” X 5/8” SCREW 1/4”-20 X T-NUT,1/2”L SCREW 1/4”-20 X (QTY: 8) 5/8”L (QTY: 8) O.D. (QTY: 8) 1/2”L (QTY: 5) (QTY: 7) 11/16”L (QTY: 2) Step 1: Assemble Ladder Tray Subassemblies Notes: If pre-assembled from manufacturer proceed to Step 2. A. Begin by assembling the front section of the ladder tray with the rear section, and then the back section with the end stop. Bolt the three assemblies together using the 1/4”-20 T27 Torx screws, flat washer, and acorn nuts. 1.877.335.2621 www.DEJANA.com Ladder Tray Installation Instructions Step 1: Assemble Ladder Tray Subassemblies, CONT’d. Notes: B. With ladder tray assembled, mark the (7) hole locations shown. Once marked, disassemble the sections you just put together, and then drill through marked holes in FRP with an 11/32” drill bit. C. Now that holes are drilled through FRP, repeat step A, and assemble the sections again using The (2) outer 1/4”-20 T27 Torx screws, flat washers, and acorn nuts. Next insert T-nuts on the top of the ladder screws seen tray using your hands, pushing the T-nut in the hole as much as you can. Then use a hammer to in ‘Detail D’ fully insert T-nut until T-nut is flush to the surface. Once T-nuts are in, fasten 1/4”-20 T30 Torx are part screws into T-nuts. number FAS 0195543. The other (5) screws used are part number FAS 0195543. 1.877.335.2621 www.DEJANA.com Ladder Tray Installation Instructions Hardware: FAS 37018 FAS 19903 FAS 33078 NYLOCK NUT, SERRATED FLANGE FLAT WASHER, 1/4”-20 (QTY: 4) BOLT, 1/4”-20 X 1/4” X 5/8” 3/4” (QTY: 4) O.D. (QTY: 4) Step 2: Install Strut and Base Tab Notes: Rear DuraRac or Rear Mount and Side Durarac Must Already Be Installed to Continue Installation A. Remove (1) bolt and accompanied washers from the Streetside baseplate. B. Insert additional strut channel and align holes in the strut channel with the holes in the transverse mounting angle of the Side DuraRac. Fasten the two together with 1/4”-20 bolts, washers, and nuts. 1.877.335.2621 www.DEJANA.com Ladder Tray Installation Instructions Step 2: Install Strut and Base Tab, CONT’d. Notes: C. With strut now fastened to transverse mounting angle, insert base tab at the bottom of the additional strut, so that the hole in the tab is over the hole in the baseplate. Then re-fasten the 5/16” bolt down to fasten the tab and baseplate. D. Mark (2) hole locations onto the additional strut. Remove 5/16” bolt from base plate yet again, along with the base tab. Drill through strut and baseplate using a 5/16” drill bit. Then re-insert base tab, fasten 5/16” bolt back down, and then fasten the base tab to the strut using (2) 1/4”-20 bolts, washers, and nuts. 1.877.335.2621 www.DEJANA.com Ladder Tray Installation Instructions Hardware: FAS 37341 FAS 10140022 SERRATED T45 TORX HEAD FLANGE NUT, SCREW 3/8”-16 X 3/8”-16 (QTY: 12) 3/4”L (QTY: 12) Step 3: Install Ladder Tray in Vehicle Notes: A. Install the (3) ladder tray straps at the pre-drilled holes in the ladder tray angle. Fasten 3/8”-16 Bolts to go T45 Torx screws and serrated nuts. Make sure that the straps are aligned straight up and leveled on inside of before fully tightening bolts. ladder tray and the nuts will be on the outside. 1.877.335.2621 www.DEJANA.com Ladder Tray Installation Instructions Step 3: Install Ladder Tray in Vehicle, CONT’d. Notes: B. Insert ladder tray into the vehicle, we typically place it about 13” from the floor mat of the vehicle, but you can set it to whatever height you would prefer. Using two people at least, put the ladder tray flush up against the rear durarac and additional strut at the side durarac, and clamp ladder tray up against them. Once clamped you can begin adjusting to the preferred height. Be sure that the height is consistent the whole way down by measuring at multiple points and using a leveling gauge. C. With ladder tray in proper position and clamped in place, mark a total of (9) holes onto the struts that the ladder tray is clamped to. 1.877.335.2621 www.DEJANA.com Ladder Tray Installation Instructions Step 3: Install Ladder Tray in Vehicle, CONT’d. Notes: D. Take clamps off and set ladder tray out of the way. Drill through the (9) marked holes with a 7/16” drill bit. Then place ladder tray back up and fasten ladder tray to struts using 3/8”-16 T45 Torx screws and serrated nuts. 1.877.335.2621 www.DEJANA.com Ladder Tray Installation Instructions – Bill of Material ITEM PART NUMBER DESCRIPTION QTY. NO. 1 DTC 0804-002 [FWD SECTION] LADDER TRAY, FRONT SECTION 1 2 DTC 0804-002 [BACK SECTION] LADDER TRAY, REAR SECTION 1 3 DTC 0813-006 LADDER TRAY STRAP 3 4 DTC 0213-075 LADDER TRAY END STOP 1 5 AUST TB9002 STRUT CHANNEL, 47.75”L 1 6 DTC 0213-076 UNISTRUT BASE TAB 1 7 FAS 0197057 1/4”-20 T-NUT, 1/2”L 7 8 FAS 33078 FLAT WASHER, 1/4” X 5/8” O.D. 12 9 FAS 10051-12025 T27 TORX HEAD SCREW 1/4”-20 X 5/8”L 8 10 FAS 37708 1/4”-20 ACORN NUT 8 11 FAS 10140022 T45 TORX HEAD SCREW 3/8”-16 X 3/4”L 12 12 FAS 37341 3/8”-16 SERRATED FLANGE NUT 12 13 FAS 19903 SERRATED FLANGE BOLT, 1/4”-20 X 3/4” 4 14 FAS 37018 NYLOCK NUT, 1/4”-20 4 15 FAS 0195544 T30 TORX HEAD SCREW 1/4”-20 X 11/16”L 2 16 FAS 0195543 T30 TORX HEAD SCREW 1/4”-20 X 1/2”L 5 1.877.335.2621 www.DEJANA.com Ladder Tray Installation Instructions – Technical Drawing 1.877.335.2621 www.DEJANA.com Ladder Tray Installation Instructions – Inspection Dimensions 1.877.335.2621 www.DEJANA.com .
Load more

Recommended publications
  • PDF Product List
    STRUCTURAL BOLTS MACHINE BOLTS NUTS A325 Screw Only, A193 B7 Heavy Hex Head Bolt Acorn (Cap) Nut Domestic & Import A307A Breakaway Bolt Allen Nut A325 Bolt with Nut A307B Heavy Head Bolt Cap (Acorn) Nut A325 Type 3 Bolt, Domestic F1554 Hex Machine Bolt Castle Nut A325 Interference Body Bolt (Grades 36, 55, & 105) Coupling Nut Canadian A325 Bolt w/DH Nut, Square Head Machine Bolt Coupling Nut, Reducer Hot Dip Galvanized Coupling Nut, Heavy Duty A490 Screw Only, BOLTS & SCREWS Hex Nut Domestic & Import Carriage Bolt Hex Nut, Left Hand TC A325 Assembly, Countersunk Bolt Hex Nut, Heavy Grade 4 Domestic& Import Counterbore Screw, 12 Point Hex Nut, Heavy, Grade 7 TC A490 Assembly, Elevator Bolt Hvy Double Recess Guardrail Nut Domestic & Import Flange Bolt Jack Nut Flat Head Bolt, Slotted Jam Nut STRUCTURAL NUTS Guardrail Bolt Jam Nut, Left Hand A194 2H Nut, Domestic Hanger Bolt Flange Nut A194 2H Nut, Import Lag Screw High Nut A563 Grade DH Heavy Nut, Lag Screw, 1-Way Truss Head Knurled Nut Domestic Lag Screw, Indented HWH Machine Screw Nut, Hex A563 DH Type 3 Nut Full Thread Machine Screw Nut, Small Pattern ANCO Heavy Hex Locknut Lag Screw, Square Head Machine Screw Nut, Square ANCO Finished Locknut Penta Head Bolt Palnut ANCO 2H Heavy Locknut Place Bolt Panel Nut ANCO A325 Locknut Plow Bolt, Grade 2 Slotted Nut Plow Bolt, Grade 5 Slotted Nut, Heavy STRUCTURAL WASHERS Plow Bolt, Grade 8 Square Nut F436 Hardened Washer Shaker Screen Bolt, Grade 5 Square Nut, Heavy Domestic & Import Shackle Bolt Tee Nut F436 Type 3 Washer Security Bolt Wing
    [Show full text]
  • Draft Standard
    PHILIPPINE AGRICULTURAL ENGINEERING STANDARD PAES 311: 2001 Engineering Materials – Bolts and Nuts for Agricultural Machines – Specifications and Applications Foreword The formulation of this National Standard was initiated by the Agricultural Machinery Testing and Evaluation Center (AMTEC) under the project entitled "Enhancing the Implementation of AFMA Through Improved Agricultural Engineering Standards" which was funded by the Bureau of Agricultural Research (BAR) of the Department of Agriculture (DA). This standard has been technically prepared in accordance with PNS 01-4:1998 (ISO/IEC Directives Part 3:1997) – Rules for the Structure and Drafting of International Standards. It provides specifications and proper application of bolts and nuts for agricultural machines. The word “shall” is used to indicate requirements strictly to be followed in order to conform to the standard and from which no deviation is permitted. The word “should” is used to indicate that among several possibilities one is recommended as particularly suitable, without mentioning or excluding others, or that certain course of action is preferred but not necessarily required. In the preparation of this standard, the following references were considered: Hummel, B. L. (Ed.) 1967. Machine design, Fastening and joining, Vol. 39 No. 34. Penton Publishing Co., Cleveland, Ohio. ISO 262:1998, ISO general purpose metric screw threads – Selected sizes for screws, bolts, and nuts ISO 273:1979, Fasteners – Clearance holes for bolts and screws ISO 888:1976, Bolts, screws, and studs – Nominal lengths and thread lengths for general purpose bolts JIS B 1052:1998, Mechanical properties of steel nuts JIS B 1057:1994, Mechanical properties of non-ferrous metal fasteners C-69 PHILIPPINE AGRICULTURAL ENGINEERING STANDARD PAES 311:2001 Engineering Materials – Bolts and Nuts for Agricultural Machines – Specifications and Applications 1 Scope This standard establishes specifications and provides technical information for the proper application of bolts and nuts for agricultural machinery.
    [Show full text]
  • ABS Fastener Catalog
    ABS FASTENERS OFFERS A COMPLETE LINE OF COMMERCIAL STANDARDS AND SPECIALS. We are your premier source for commercial grade fasteners, nuts, bolts, screws, and hard- ware. For more than 60 years, ABS has set the standard for quality, value-added services, and superior customer service. From our seven ABS warehouses strategically located across the USA and Mexico stocking several million in inventory, we are uniquely poised to serve your fastener and hardware needs for manufacturing and assembly. 4 ...........Anchors 20 .........Custom Fasteners & Hardware 5 ...........Bits 21 .........Value Added Services 6-7 ........Bolts 22 .........Quick Fastener Reference 8-9 ........Nuts 23 .........Heads, Threads, and Drive Styles 10 .........Washers 24 .........Thread Pitch Guide 11 .........Socket Products 25 .........Material Reference 12 .........Machine Screws 26 .........Plating Reference 13 .........Wood Screws 27 .........Painting Services 14 .........Construction Screws 28 .........Staple Reference 15 .........Self Drilling Screws 29 .........Nail Reference 16-17 ...Sheet Metal Screws 30 .........Hardware Off ering 18 .........Nails & Rivets 29 .........ABS Locations & Contact Info 19 .........Pins & Miscellaneous Items © 2017 American Bolt & Screw. All Rights Reserved. Reproducing or copying any part of this catalog without permission is unlawful under the United States Copyright Act. Violaters are subject to full prosecution under federal law. We hold industry together... You are not anchored to other suppliers! We have the anchors you need for light or heavy jobs. Conical Plastic Anchors E-Z Anchors Toggle Bolts Light-duty wall anchor used with a sheet metal or wood Pre-drills own hole in gympsum wallboard.Replaces A machine screw and toggle wing anchoring system screw in drywall,concrete or hollow brick.
    [Show full text]
  • Workholding Components
    WORKHOLDING COMPONENTS Workholding Components Adjustable Clamp Heels............................................................268 Nuts, Spinner-Grip™...................................................................255 Adjustable Clamp Rests ............................................................267 Nuts, Stainless Steel...................................................................257 Adjustable Step Blocks .............................................................278 Nuts, T-Slot ..................................................................................258 Assemblies, Spherical Flange ..................................................254 Plastic Pad Covers ......................................................................240 Bolts, Dovetail .............................................................................252 Revolving Clamp Assemblies, Long Bushing Type .............232 Bolts, Swing .................................................................................235 Revolving Clamp Assemblies, Short Bushing Type.............232 Bolts, T ..........................................................................................252 Revolving Clamp Base ...............................................................232 Bolts, T-Slot ..................................................................................251 Rod Ends ......................................................................................236 Bolts, T-Strap ...............................................................................247
    [Show full text]
  • UNITED's Nuts! Acorn, Lock - Spherical Flange Coupling, Lock and Flange Nuts GET MORE for LESS at UNITED! ACORN NUTS See Section G for Stainless
    Nuts: Acorn-Coupling- UNITED's Nuts! Acorn, Lock - Spherical Flange Coupling, Lock and Flange Nuts GET MORE FOR LESS AT UNITED! ACORN NUTS See Section G for Stainless. Closed end ACORN NUT A B C protects stud UDB-925000 1/4-20 1/2 1/2 threads from UDB-925005 5/16-18 5/8 9/16 damage. Heat UDB-925010 3/8 – 16 3/4 11/16 treated black UDB-925015 1/2-13 15/16 7/8 B oxide finish. UDB-925020 5/8-11 1-3/16 1-1/16 UDB-925025 3/4 – 10 1-3/8 1-1/4 C12L15 STEEL — HEAT TREATED WITH BLACK OXIDE FINISH. UDB-925030 7/8 – 9 1-7/16 1-7/16 KNURLED LOCK NUTS See Section G for Stainless. Quick thread 1018 STEEL — HEAT TREATED — BLACK OXIDE locking on jigs STEEL STAINLESS A THD B O. D. C STEP D E F DIA PART NO. PART NO. I. D. SIZE DIA DIA WIDTH LIP +.005 and fixtures. 1/4 -.000 detents permit UDB-925110 UDB-925110S 1/4 – 20 1-1/8 1" 7/16 1/16 .250 additional UDB-925115 UDB-925115S 3/8 – 16 1-1/8 1" 7/16 1/16 .250 tightening with UDB-925120 UDB-925120S 1/2 – 13 1-1/8 1" 7/16 1/16 .250 1/4" pin. UDB-925125 UDB-925125S 5/8 – 11 1-3/8 1" 7/16 1/16 .250 COUPLING NUTS Makes unlimited COUPLING NUT A B C stud length UDB-925050 3/8 – 16 1 11/16 combinations UDB-925055 1/2-13 1-1/4 7/8 available.
    [Show full text]
  • Fasteners & Bolts
    Parts for Trucks, Trailers & Buses ® 11 FASTENERS Proven, reliable and always innovative. TRP® offers reliable aftermarket products that are designed and tested to exceed customers’ expectations regardless of the vehicle make, model or age. BOLTS • Clips • GROMMETS • inserts • nuts • sCrews • washers Tested. Reliable. Guaranteed. TABLE OF CONTENTS Fasteners FASTENERS Fastener Guide ..............................11-4 Choosing the right Bolts ......................................11-6 replacement part or service for your vehicle—whether you own Clips .....................................11-39 one, or a fleet—is one of the Collars ....................................11-44 most important decisions you can make for your business. Cotter ....................................11-45 ® And, with tested TRP parts Fastener Assortment for HWU10000 ............11-48 it’s an easy decision. Fastener Assortment for HWU11301 ............11-50 Regardless of the make Grommets .................................11-53 you drive, TRP® quality replacement parts are Huck Bolts .................................11-54 engineered to fit your truck, Huck Collars ...............................11-56 trailer or bus. Choose the parts that give you the best Huck Fastener Tools .........................11-57 value for your business. Check Inserts ....................................11-59 them out at an approved TRP® retailer near you. Kits ......................................11-66 Nuts .....................................11-67 Pins ......................................11-86 The cross reference information in this catalog is based upon data provided by several industry sources and our partners. While every attempt is made to ensure the information presented is accurate, we bear no liability due to incorrect or incomplete information. Product Availability Due to export restrictions and market ® demands, not all products are TRP North America always available in every location. 750 Houser Way N. Check for availability in your area with your local TRP® Distributor.
    [Show full text]
  • HARDWARE LISTIN(J
    HARDWARE LISTIN(j 812 SCREW, 1/4-20 X 1-1/2 knurled socket 1203 SCREW, No. 8-32 X 7/8 Pozidriv fillister hd. (chrome) hd. (Grade 2 steel) 813 SCREW, 1/4-20 X 1-3/4 knurled socket 1205 SCREW, No.1 0-24 X 3/4 Pozidriv fillister hd. (chrome) hd. 852 SCREW, 1/4-20 X 1 knurled socket hd. 1309B SCREW, No. 10-32 X 1/2 Phillips Truss 853A SCREW, 5/16-18 X 12-1/4 knurled hd. (self-sealing) socket hd 1311A SCREW, No. 8-32 X 1/2 Truss hd. (self- 854A SCREW, 5/16-18 X 2-1/4 socket hd. sealing) (Grade 2 steel). 1357W SCREW, 1/4-20 X 1 Phillips oval ctsk. hd. 854 SCREW, 3/8-24 X 2 knurled socket hd. (stai nless) 855B SCREW, 3/8-16 X 2 knurled socket hd. 1601 SCREW, No. 8-32 X 1/2 Pozidriv flat ctsk. 856A SCREW, 5/16-24 X 1 knurled socket hd. hd. (Grade 2 steel) 857A SCREW, No.1 0-24 X 3/8 knurled socket 1602 SCREW, 1/4-20 X 3/4 flat hd. (Grade 2 hd. (black) ste'el) 860 SCREW, 3/8-16 X 2 knurled socket hd. 1610 SCREW, 5/16-24 X 1-1/2 Pozidriv flat (black) ctsk. hd. (Grade 2 steel) 864 SCREW, 114-20 X 7/16 socket pan hd. 1611 SCREW, No. 10-32 X 3/4 Pozidriv flat 866 SCREW, 5/16-18X 1-1/8 knurled socket ctsk. hd.
    [Show full text]
  • BRIGHTON-BEST INTERNATIONAL * Rohs Compliant Product
    Revised February 2018 Toll Free: 1-800-275-0050 BRIGHTON-BEST INTERNATIONAL * RoHS compliant product www.brightonBEST.com PIPE PLUGS LONG ARM HEX KEYS L9® FASTENING SYSTEM 232 18-8 Stainless Steel Dry Seal 512 6150 CRV Alloy (Import) Plain 446 L9 Collar Locknuts Cad. Yellow & 3/4 Taper 519 8650 Alloy Plain Wax (USA) 447 USS Tension Flat Washers 528 8650 CRV Alloy (Metric) Plain CUP POINT SET SCREWS Zinc/Yel (USA) 514 6150 Alloy (Import) SOCKET PRODUCTS 101/601 Alloy Plain 448 SAE Tension Flat Washers Zinc/Yel (USA) 873* Alloy Zinc Bake HEX KEY SETS SOCKET CAP SCREWS 838 Alloy Mechanical Zinc 529 8650 Alloy (Inch/Metric) Sets HEX BOLTS 011/581 Alloy Plain 105 Alloy Plain Nylon Patch (USA) Plain 493 A307 Grade A Plain 872* Alloy Zinc Bake 816 Alloy Locking Socket Jam 494* A307 Grade A Zinc 837 Alloy Mechanical Zinc Screw Plain 495 A307 Grade A HDG 015 Alloy Plain Nylon Patch 533 Alloy Class 14.9 DIN 916 Plain 195 A307 Grade A Zinc/Yel 307 Alloy Plain 1936 Series 877 Alloy Class 14.9 DIN 916 Zinc Bake 532 Alloy Class 12.9 Plain DIN 912 102/602 18-8 Stainless Steel HEAVY HEX BOLTS 104 316 Stainless Steel 876* Alloy Class 12.9 Zinc Bake DIN 912 BOLT PRODUCTS 505 A193 Grade B7 Plain 539 A2 Stainless Steel 012/592 18-8 Stainless Steel 484 A307 Grade B Plain 067 45H ISO 4029 / DIN 916 Mechanical GRADE 2 014 316 Stainless Steel 167* A307 Grade B Zinc Zinc 402 Grade 2 Plain 538 A2 Stainless Steel 168 A307 Grade B HDG 403* Grade 2 Zinc 549 A4 (316) Stainless Steel ASSORTED PT.
    [Show full text]
  • Glossary of Industry Terms
    Glossary Of Industry Terms A A/F An abbreviation for Across Flats. Used in reference to the dimensions on hexagon head products. ACORN NUT A nut (so-called because of its shape) that has a domed top so that it prevents contact with the external thread. AIRCRAFT QUALITY In the fastener industry, aircraft quality refers to parts that are made to more stringent specifications, and tested more thoroughly, than commercial fasteners because they are used in high-risk and/or high-stress applications requiring near-zero defects. ALLOWANCE An intentional clearance between internal or external thread and the design form of the thread when the thread form is on its maximum metal condition. Not all classes of fit have an allowance. For metric threads the allowance is called the fundamental deviation. ALLOY STEEL Alloy steel is steel containing alloying elements, other than carbon, which have been added to achieve defined mechanical of physical proper- ties and performance. Alloy steel has greater tensile and yield strength than medium carbon steel. ANAEROBIC ADHESIVE An adhesive which hardens in the absence of air, such adhesives are often used as a thread locking medium. ANGLE CONTROLLED TIGHTENING A tightening procedure in which a fastener is first tightened by a pre-selected torque (called the snug torque) so that the clamped surfaces are pulled together, and then is further tightened by giving the nut an additional measured rotation. Frequently bolts are tightened beyond their yield point by this method in order to ensure that a precise preload is achieved. Bolts of short length can be elongated too much by this method and the bolt material must be sufficiently ductile to cater for the plastic deformation involved.
    [Show full text]
  • Finished Hex Head Bolts Grade 2, 5, 8 and L9
    Finished Hex Head Bolts Grade 2, 5, 8 and L9 SAE Grade 2, ASTM A307 Plain = HC020------- Zinc = HC020-------Z1 SAE J429 Grade 5, ASTM A449 Plain = HC050-------00D Zinc = HC050-------Z1D SAE J429 Grade 8, ASTM A490 Plain = HC080-------00D Zinc = HC080-------Z1D SAE J429 Grade L9, ASTM F606 (Note 1) Zinc = HCL90-------Z1 Tap Bolts/Fully Threaded HCT020------- HCT050------- HCT080------- D F C H Weight Width Bolt Body Width Across Flats Across Height Rough Estimate Diameter Diameter Corners Max Basic Max Min Max Min Basic Per Each ¼ 0.260 7/16 0.438 0.425 0.505 0.484 11/64 .003 + .014 x inch 5/16 0.324 1/2 0.500 0.484 0.577 0.552 7/32 .007 + .021 x inch 3/8 0.388 9/16 0.562 0.544 0.650 0.620 1/4 .012+ .030 x inch 1/2 0.515 3/4 0.750 0.725 0.866 0.826 11/32 .034 + .055inch 5/8 0.642 15/16 0.938 0.906 1.083 1.033 27/64 .063 + .084 x inch 3/4 0.768 1-1/8 1.125 1.088 1.299 1.240 1/2 .128 + .125 x inch 7/8 0.895 1-5/16 1.312 1.269 1.516 1.447 37/64 .188 + .180 x inch 1 1.022 1-1/2 1.500 1.450 1.732 1.653 43/64 .219 + .230 x inch 1-1/8 1.149 1-11/16 1.688 1.631 1.949 1.859 3/4 .353 + .280 x inch 1-1/4 1.277 1-7/8 1.875 1.812 2.165 2.066 27/32 .509 + .345 x inch 1-3/8 1.404 2-1/16 2.062 1.994 2.382 2.273 29/32 1-1/2 1.531 2-1/4 2.250 2.175 2.598 2.480 1 .920 + .500 x inch 1-3/4 1.785 2-5/8 2.625 2.538 3.031 2.893 1-5/32 1.37 + .700 x inch 2 2.039 3 3.000 2.900 3.464 3.306 1-11/32 2.16 + .890 x inch 2-1/4 2.305 3-3/8 3.375 3.262 3.897 3.719 1-1/2 2-1/2 2.559 3-3/4 3.750 3.625 4.330 4.133 1-21/32 Dimensional specifications per ASME B18.2.1 STANDARD THREAD Bolt lengths ≤ 6”: Thread length = (2 X diameter) + 1/4” LENGTH Bolt lengths > 6”: Thread length = (2 X diameter) + 1/2” Note 1: L9 Head height is not accurate in this chart.
    [Show full text]
  • P E R F E C T I O N I N D E F L E C T I
    INCH CATALOG C D B A PERFECTION IN DEFLECTION Table of Contents Letter from the President 3 Automation Locknuts 4,5 CollarPlus™ Locknuts 6 Flange Center Locknuts 7 TechPlus™ Locknuts 8 Finished Hex Center Locknuts 9 Jam and Machine Screw Top Locknuts 10 Acorn and Special Locknuts 11 Technical Information 12 Locknut Specifications 16 13 Locknut Applications 16 14 16 2 Letter from the President From Aztech’s inception, quality has been our consistent theme. We have engineered quality into every facet of the company’s work. We think quality products and productivi- ty go hand in hand, so we build solid relationships with our customers by always striving to be your partner in productivity. True partnerships are not built overnight, but take time to develop. At Aztech, we believe that trust, commitment and an understanding of your individual needs are the founda- tion blocks to building a lasting and mutually beneficial relationship. One of the great resources Aztech offers is being a single source for all your locknut and freespinning nut needs, from basic standards to fully custom designs. We reduce the time required to purchase and inspect nuts and locknuts. Your Aztech team stands ready to serve your every need with the broadest selection of quality nuts and attentive personal service. Let us deliver Perfection In Deflection... to you. Mark Kaindl President Aztech Locknut Company All sales by Aztech Locknut Company are made pursuant to the terms and conditions in effect during the time of deliv- ery. Aztech Locknut Company shall not be held liable to the buyer or anyone else for any defect in goods that results in personal injury, death, property damage, loss of use or replacement costs.
    [Show full text]
  • BRIGHTON-BEST INTERNATIONAL Toll Free 1-800-275-0050 METRIC FASTENER PRODUCT LINES
    www.brightonbest.com Revised June 2021 BRIGHTON-BEST INTERNATIONAL Toll Free 1-800-275-0050 METRIC FASTENER PRODUCT LINES SOCKET PRODUCTS ALLOY STANDARD SOCKET PRODUCTS STAINLESS STANDARD HEX CAP SCREWS 10.9 STANDARD 854 Socket Head Cap Screws Coarse 8.8 Alloy DIN 912 823 Flat Socket Cap Screws A2 Stainless DIN 7991 / ISO 10642 462 Full Thread Fine Plain DIN 961 / ISO 8676 Thermal Black Oxide 862 Flat Socket Cap Screws A4 Stainless DIN 7991 / ISO 10642 165 Partial Thread Coarse Zinc Yellow Bake CR+6 DIN 931 / ISO 4014 718 Socket Head Cap Screws 8.8 Alloy Zinc CR+3 DIN 912 541 Cup Point Set Screw A4 Stainless DIN 916 165 Full Thread Coarse Zinc Yellow Bake CR+6 DIN 933 / ISO 4017 532 Socket Head Cap Screws 12.9 Alloy Plain DIN 912 / ISO 4762 THREADED ROD STANDARD 164 Partial Thread Coarse Plain ASME B18.2.3.1M 876 Socket Head Cap Screws 12.9 Alloy Zinc Bake CR+3 DIN 912 / ISO 4762 164 Full Thread Coarse Plain ASME B18.2.3.1M 066 Socket Head Cap Screws 12.9 Alloy Mechanical Zinc DIN 912 / ISO 4762 V34 All Thread Rod 4.6 Plain DIN 975 CR+3 737 All Thread Rod 4.6 Zinc CR+3 DIN 975 HEX CAP SCREWS STAINLESS STANDARD 531 Low Head Socket Cap Screws Alloy 10.9 Plain DIN 7984 V37 All Thread Rod B7 Plain DIN 975 830 A2 Stainless Partial Thread Coarse DIN 931 / ISO 4014 213 Low Head Socket Cap Screws 8.8 Plain DIN 7984 871 All Thread Rod A2 Stainless DIN 975 830 A2 Stainless Full Thread Coarse DIN 933 / ISO 4017 533 Socket Set Screws Cup Point Alloy 14.9 Plain DIN 916 / ISO 4029 869 All Thread Rod A4 Stainless DIN 975 797 A4-70 Stainless Partial
    [Show full text]