90034 Rev 90034-20090416

10006 Santa Fe Springs Road Santa Fe Springs, CA 90670 USA Made in China Owner’s Manual and Operating Instructions

Gasoline Powered HYDRAULIC AUGER

Table of Contents

Introduction ...... 1 Maintenance ...... 12 Portable Hydraulic Auger/Post Hole Engine Maintenance ...... 12 Digger ...... 1 Oil ...... 12 Accessories ...... 1 Spark Plugs ...... 12 This Booklet ...... 1 Air Filter ...... 12 Manual Conventions ...... 2 Cleaning ...... 13 Safety Rules ...... 3 Maintenance Schedule ...... 13 Controls and Features ...... 5 Auger/Post Hole Digger Maintenance ... 13 Auger/Post Hole Digger ...... 5 Storage ...... 14 Assembly ...... 6 Engine Storage ...... 14 Open Shipping Crate ...... 6 Specifications ...... 15 For parts reference see pages 16-18 in Auger/Post Hole Digger Specifications .. 15 the manual...... 6 Hydraulic Oil ...... 15 Step 1 – Engine Carriage Assembly ...... 6 Auger/Post Hole Digger Parts Diagram . 16 Step 2 – Attach Wheels ...... 6 Auger/Post Hole Digger Parts List ...... 17 Step 3 – Attach Boom ...... 7 Engine Parts Diagram ...... 19 Step 4 – Attach hose retaining bracket .... 7 Engine Parts List ...... 20 Step 5 – Feed the hydraulic hoses and Troubleshooting ...... 23 wires through the boom ...... 7 Warranty ...... 24 Step 6 – Attach handle assembly to boom7 Warranty Qualifications ...... 24 Step 7 – Connect hydraulic hoses ...... 7 Repair/Replacement Warranty ...... 24 Step 8 – Wire connections ...... 8 Do not return the unit to the place of Step 9 – Attach the towing coupler ...... 8 purchase ...... 24 Step 10 – Attach the Auger coupler ...... 8 Warranty Exclusions ...... 24 Add Engine Oil ...... 9 Normal Wear ...... 24 Add Engine Fuel ...... 9 Installation, Use and Maintenance .....24 Add Hydraulic Oil ...... 9 Other Exclusions ...... 24 Operation ...... 10 Limits of Implied Warranty and Auger/Post Hole Digger Location ...... 10 Consequential Damage ...... 24 Starting the Engine ...... 10 Contact Information ...... 24 Stopping the Engine ...... 10 Address ...... 24 Digging Operation ...... 10 Customer Service ...... 24 See Following Diagrams...... 11 Technical Service ...... 24 Notes ...... 25

Introduction

Introduction Accessories Champion Power Equipment manufactures Congratulations on your purchase of a and sells accessories designed to help you Champion Power Equipment Auger/Post get the most from your purchase. To find out Hole Digger. CPE designs and builds Augers more please visit our web site at to strict specifications. With proper use and maintenance, this Auger/Post Hole Digger www.championpowerequipment.com will bring years of satisfying service.

This Owner’s Manual contains important This Booklet safety instructions and information. SAVE Every effort has been made to ensure the THESE INSTRUCTIONS FOR FUTURE accuracy and completeness of the REFERENCE. information in this manual. We reserve the right to change, alter and/or improve the product and this document at any time Portable Hydraulic without prior notice. Auger/Post Hole Digger This unit is a gasoline engine driven Auger/Post Hole Digger. It is designed to dig post holes. Engine is shipped without oil and requires oil SAE10w-30 motor oil before starting. Before starting the engine fill the hydraulic tank with 10W AW 32 anti wear hydraulic fluid (3.9 gal/15 L)

Record the model and serial numbers as well as date and place of purchase for future reference. Have this information available when ordering parts and when making technical or warranty inquiries.

Champion Power Equipment Support 1-877-338-0999 Model Number 90034 Serial Number

Date of Purchase

Purchase Location

Rev 90034-20090416 1 Manual Conventions

CAUTION Manual Conventions This manual uses the following symbols to CAUTION indicates a potentially hazardous help differentiate between different kinds of situation which, if not avoided, may result in minor or moderate injury. information. The safety symbol is used with a key word to alert you to potential hazards in operating and owning power equipment.

Follow all safety messages to avoid or reduce the risk of serious injury or death. CAUTION

DANGER CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

NOTE If you have questions regarding your Auger/Post WARNING Hole Digger, we can help. Please call our help line at 1-877-338-0999. WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

2 Rev 90034-20090416 Safety Rules

DO NOT remove hitch pin or Auger Pin when the Safety Rules engine is running. Keep hands and feet away from rotating parts. Tie up long hair and remove jewelry. Operate equipment with guards in place. WARNING DO NOT wear loose-fitting clothing, dangling drawstrings or items that could become caught. Read this manual thoroughly before operating your Auger/Post Hole Digger. Failure to follow instructions could result in serious injury or death. WARNING

Sparks can result in fire or electrical shock.

When servicing the engine: Disconnect the spark plug wire and place it WARNING where it cannot contact the plug. DO NOT check for spark with the plug removed. The engine exhaust from this product contains Use only approved spark plug testers. chemicals known to the state of California to cause cancer, birth defects, or other reproductive harm. WARNING

Running engines produce heat. Severe burns can occur on contact. Combustible material can catch fire on contact. DANGER DO NOT touch hot surfaces. Auger/Post Hole Digger engine exhaust contains Avoid contact with hot exhaust gases. carbon monoxide, a colorless, odorless, poison Allow equipment to cool before touching. gas. Breathing carbon monoxide will cause Maintain at least three feet of clearance on all nausea, dizziness, fainting or death. If you start sides to ensure adequate cooling. to feel dizzy or weak, get to fresh air Maintain at least five feet of clearance from immediately. combustible materials.

Operate Auger/Post Hole Digger outdoors only in a well ventilated area. DO NOT operate the Auger/Post Hole Digger WARNING inside any building, enclosure or compartment. DO NOT allow exhaust fumes to enter a confined Skin Injection Hazard. High pressure hydraulic area through windows, doors, vents or other oil can inject under your skin. openings. DANGER CARBON MONOXIDE, using a Make sure all fittings are tightly secure before Auger/Post Hole Digger indoors CAN KILL YOU applying pressure. Relieve system of pressure IN MINUTES. before servicing.

DANGER WARNING

Rotating parts can entangle hands, feet, hair, Rotating Hazard clothing and/or accessories. Entanglement in Auger/Post Hole Digger will Traumatic amputation or severe laceration can cause serious injury or death. Keep away from result. Auger when engine is running.

Rev 90034-20090416 3 Safety Rules

When adding or removing fuel WARNING Turn the engine off and let it cool for at least two minutes before removing the fuel cap. Loosen Cables and Pipelines Hazard the cap slowly to relieve pressure in the tank. Only fill or drain fuel outdoors in a well-ventilated Auger/Post Hole Digger will cut through buried area. electrical cables and gas pipelines resulting in DO NOT overfill the fuel tank. serious injury or death. Contact your local utilities Always keep fuel away from sparks, open flames, company before drilling holes in the ground. pilot lights, heat and other sources of ignition. DO NOT light or smoke cigarettes. When starting the engine DO NOT attempt to start a damaged engine. WARNING Make certain that the gas cap, air filter, spark plug, fuel lines and exhaust system are properly in place. Incline Hazard Allow spilled fuel to evaporate fully before attempting to start the engine. Do not operate machine on hills or inclines that When storing the Auger/Post Hole are steeper than 15 degrees. Machine can roll away and tip over. Digger: Store away from sparks, open flames, pilot lights,

heat and other sources of ignition.

WARNING WARNING Projectile Hazard

Rock, dirt, and debris may fly out of work area. Rapid retraction of the starter cord will pull hand Wear safety glasses and protective clothing. and arm towards the engine faster than you can Keep bystanders away from work area. let go.

Unintentional startup can result in entanglement, traumatic amputation or laceration. WARNING Broken bones, fractures, bruises or sprains could Towing Hazard result.

Review towing safety warnings in your towing When starting engine, pull the starter cord slowly vehicle manual. until resistance is felt and then pull rapidly to Drive safely. Be aware of the added length of the avoid kickback. Auger/Post Hole Digger. NEVER ride or transport cargo on the Auger/Post Hole Digger. Choose a level surface to operate the Auger/Post CAUTION Hole Digger. NEVER EXCEED MAX. Towing Speed 45 MPH Improper treatment or use of the Auger/Post Hole Digger can damage it, shorten its life and void your warranty. DANGER Use the Auger only for intended uses. Fuel and fuel vapors are highly flammable and Operate only on level surfaces. extremely explosive. DO NOT expose Auger engine to excessive moisture, dust, or dirt. DO NOT allow any material to block the cooling Fire or explosion can cause severe burns or slots. death. DO NOT use the engine if: Equipment sparks, smokes or emits flames Unintentional startup can result in entanglement, Equipment vibrates excessively traumatic amputation or laceration.

4 Rev 90034-20090416 Controls and Features

Controls and Features Read this owner’s manual before operating your Auger/Post Hole Digger. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference.

Auger/Post Hole Digger

(1) Trigger – The trigger is used to start, (8) Hydraulic Oil Breather Cap – stop, and reverse the Auger bit. Remove cap to fill hydraulic tank with oil.

(2) Emergency Stop Button – (9) Engine – 270cc Gasoline driven Emergency engine stop button. engine.

(3) Auger Handle – Tilt control for Auger (10) 2” Ball Coupler – Attaches the Auger bit. to your vehicle.

(4) Hydraulic Motor – Spins Auger bit. (11) Engine Pivot – Allows engine to swing freely when operating Auger. (5) Control Valve – Directs the hydraulic oil to the hydraulic motor. (12) Hydraulic tank

(6) Work port Hydraulic hoses – These (13) Hydraulic filter hoses carry the hydraulic oil from the control valve to the hydraulic motor. (14) Strainer

(7) Pivot bolt – Adjust pivot bolt to rotate (15) Hydraulic Pump the Auger bit and handle when drilling on a slope. (16) Auger Bit

Rev 90034-20090416 5 Assembly

Assembly The Auger/Post Hole Digger requires some assembly.

If you have any questions regarding the assembly of your Auger/Post Hole Digger, call our help line at 1-877-338-0999. Please have your serial number and model number available.

Open Shipping Crate 1. Set the shipping crate on a solid, flat surface. 2. Carefully cut the shipping bands and remove lid of shipping crate. 3. Using two people to lift, carefully remove all parts and components. 4. Locate all hardware before beginning assembly. Step 2 – Attach Wheels 1. Attach wheel to axle using 4 M12x25 For parts reference see pages bolts. Repeat actions for other side 16-18 in the manual.

Step 1 – Engine Carriage Assembly The Engine is mounted to the hydraulic tank – together they make the Engine Carriage. The Engine Carriage attaches to the frame and is designed to swing freely when operating the Auger/Post Hole Digger. This swinging movement allows the engine and hydraulic tank to stay level, avoiding fuel and oil spillage.

1. Use M20x60 bolt, lock washer, nut, and lock nut to attach engine carriage to frame

6 Rev 90034-20090416 Assembly

Step 3 – Attach Boom 1. Line up holes on boom with holes on axle. 2. Attach and secure boom to axle with M10x35 Flange bolts, Flat Washer Ø10, Lock Washer Ø10 and M10 nuts.

Step 6 – Attach handle assembly to boom 1. Slides handle tube into the boom. 2. Install M10x35 bolt and Ø10 flat washer through the boom pivot bracket and into the nut welded to the handle assembly. 3. Tighten bolt until handle is secure and does not rotate. 4. Thread M10 nut onto the end of the M10x35 .Do not tighten the nut against

the weld nut; the nut acts as a stop so that the M10x35 bolt cannot fall out or Step 4 – Attach hose be loosened too far when making retaining bracket adjustments.

The hose retaining bracket protects the hydraulic hoses on the handle assembly. 1. Align holes in hose retaining bracket (A) with the holes on the handle frame 2. Fasten retaining bracket to handle with (2) M6x20 bolts, (2) M6 nuts, (2) Ø6 flat washers and (2) Ø6 lock washers.

Step 7 – Connect hydraulic hoses 1. Connect hose 2400 to the hydraulic pump outlet (A) 2. Connect hose 2550 to the hydraulic filter (B) 3. Make sure the hoses have enough slack to allow the engine carriage to swing freely. Step 5 – Feed the hydraulic hoses and wires through the boom 1. Feed the hydraulic hoses and wires through the boom pole

Rev 90034-20090416 7 Assembly

Step 10 – Attach the Auger Step 8 – Wire connections coupler The emergency stop wire contains a 1. Slide Auger coupler (C) into motor shaft white wire and black wire. (E) and lock in place with a lock pin (D) 1. Remove gas tank nut (E) and attach 2. Place Ø10x32 cotter less hitch pin in its white wire to stud, replace nut. storage location. This is the travel pin 2. Locate available snap in plug in the wire and will be used for moving and towing bundle (B), and snap in to receptacle the Auger. plug (C) on the emergency stop wire (black wire).

Step 9 – Attach the towing coupler 1. Fasten the 2” ball coupler to the frame using (2) M12x80 bolts, (2) Ø12 Flat Washer and (2) M12 lock nut. Tighten. 2. Attach the towing chains to the towing chain mount plate with (2) M12x45 bolts, (2) Ø12 Flat washers and (2) M12 lock nut. Bolt the first link in each towing chain. 3. Tighten all hardware

8 Rev 90034-20090416 Assembly

DO NOT mix oil and gasoline. Add Engine Oil Fill tank to approximately ¼” below the top of the tank to allow for fuel expansion. DO NOT fill fuel tank indoors. CAUTION DO NOT fill fuel tank when the engine is running or hot. DO NOT attempt to crank or start the engine DO NOT overfill the fuel tank. before it has been properly filled with the DO NOT light cigarettes or smoke when filling the recommended type and amount of oil. Damage fuel tank. to the Auger/Post Hole Digger as a result of failure to follow these instructions will void your warranty. Add Hydraulic Oil

1. Make sure the Auger is on a flat, level 1. Make sure the Auger is on a flat, level surface. surface. 2. Remove the oil breather cap from the oil 2. Remove oil fill cap/dipstick to add oil. tank (A). 3. Add 1.16 qt (1.1 L) of oil and replace oil 3. Add 3.9 gallons/15 L of hydraulic oil - fill cap/dipstick. 10W AW32, ASLE H-150, or ISO 32 are 4. Check engine oil level daily and add as all acceptable types of fluid. needed.

CAUTION

The engine is equipped with a low-oil-shutoff and will stop when the oil level in the crankcase falls below the threshold level.

NOTE

Check oil often during the break-in period. Refer to the Maintenance section for recommended service intervals.

Add Engine Fuel 1. Use clean, fresh, regular unleaded fuel with a minimum octane rating of 85. 2. DO NOT mix oil with fuel. 3. Clean the area around the fuel cap. 4. Remove the fuel cap 5. Slowly add fuel to the tank. DO NOT overfill. Allow approximately ¼ inch of space for fuel expansion. 6. Screw on the fuel cap and wipe away any spilled fuel.

CAUTION

Use regular unleaded gasoline with a minimum octane rating of 85.

Rev 90034-20090416 9 Operation

Operation NOTE If the engine starts but does not run make Auger/Post Hole Digger certain that the Auger/Post Hole Digger is on a Location flat, level surface. The engine is equipped with a low oil sensor that will prevent the engine from This Auger/Post Hole Digger must have at running when the oil level falls below a critical least five feet of clearance from combustible threshold. material. Leave at least three feet of clearance on all sides of the Auger to allow for adequate cooling, maintenance and servicing. DO NOT place the Auger/post Stopping the Engine Hole Digger near vents or intakes where 1. Turn the ignition switch to the “Off” engine exhaust fumes could be drawn into position. occupied or confined spaces. Carefully 2. Turn the fuel valve to the “Off” position. consider wind and air currents when positioning Auger. Digging Operation Starting the Engine 1. Use lock pin to attach the Auger bit to 1. As much as possible, make certain the the Auger coupler. Auger/Post Hole Digger is on a flat, level surface. 2. Flip engine switch to “ON” position. 3. Move the fuel lever (Item C) to the “ON” position (to the right).

2. Position the machine so that it is level as possible. If digging on an incline, position the Auger so that it will not roll away or towards you. Loosen the pivot bolt and rotate the handle to the desired angle. 3. Use the Auger handle to position the Auger bit for digging. 4. Move the choke lever (Item B) to the 4. Squeeze the right side of the trigger to “Choke” position (to the left). dig. 5. Pull the starter cord slowly until 5. As you dig, push the handle down to the resistance is felt and then pull rapidly ground in tandem with the drilling 6. As engine warms up, move the choke action of the Auger bit. DO NOT force lever to “Run” (to the right). it. 7. Move the throttle lever (Item A) to the 6. Periodically lift the Auger to clear loose “Fast” position. dirt from the hole. 7. If the Auger becomes stuck, squeeze the left side of the trigger to reverse the rotation of the Auger.

10 Rev 90034-20090416 Assembly

See Following Diagrams.

Rev 90034-20090416 11 Maintenance

Maintenance The owner/operator is responsible for all periodic maintenance.

WARNING

Never operate a damaged or defective Auger. Spark Plugs 1. Remove the spark plug cable from the spark plug. 2. Inspect the electrode on the plug. It must be clean and not worn to produce WARNING the spark required for ignition. 3. Make certain the spark plug gap is 0.7 - Improper maintenance will void your warranty. 0.8mm (0.028 - 0.031 in.). 4. Refer to the spark plug recommendation chart when replacing the plug. 5. Carefully thread the plug into the

engine. Complete all scheduled maintenance in a 6. Use the spark plug tool to firmly install timely manner. Correct any issue before the plug. operating the Auger/Post Hole Digger. 7. Attach the spark plug wire to the plug.

NOTE Air Filter 1. Unscrew wing nut to remove the air For service or parts assistance, contact our help line at 1-877-338-0999. filter cover. 2. Unscrew wing nut to remove the air filter. 3. Separate the foam element and the Engine Maintenance paper element. To prevent accidental starting, remove and 4. Tap the paper filter element to remove ground spark plug wire before performing dirt and debris. Use compressed air (25 any service. PSI) to clear debris. 5. For the foam element: Wash in liquid detergent and water. Squeeze Oil thoroughly dry in a clean cloth. Change oil when the engine is warm. Refer 6. Saturate in clean engine oil. to the oil specification to select the proper 7. Squeeze in a clean, absorbent cloth to grade of oil for your operating environment. remove all excess oil. 1. Remove the oil drain plug with a 12 mm 8. Reassemble the two elements and socket and extension. reattach. Tighten wing nut 2. Allow the oil to drain completely. 9. Reattach the air filter cover and snap in 3. Replace the drain plug. place. 4. Remove oil fill cap/dipstick to add oil. 5. Add 1.16 qt (1.1 L) of oil and replace oil fill cap/dipstick. 6. Dispose of used oil at an approved waste management facility.

12 Rev 90034-20090416 Maintenance

Auger/Post Hole Digger Cleaning Maintenance Make certain that the Auger/Post Hole CAUTION Digger is kept clean and stored properly. DO NOT expose the unit to extreme DO NOT spray engine with water. conditions, excessive dust, dirt, moisture or corrosive vapors. Water can contaminate the fuel system.

Use a damp cloth to clean exterior surfaces CAUTION of the engine. Use a soft bristle brush to remove dirt and DO NOT use a garden hose to clean the oil. Auger/Post Hole Digger. Use an air compressor (25 PSI) to clear dirt and debris from the engine. Water can enter the engine through the cooling slots and damage the engine windings.

Maintenance Schedule Use a damp cloth to clean exterior surfaces Follow the service intervals indicated in the of the Auger. schedule below. Use a soft bristle brush to remove dirt and Service your Auger/Post Hole Digger more oil. frequently when operating in adverse Use an air compressor (25 PSI) to clear dirt conditions. and debris from the Auger. Contact our help line at 1-877-338-0999 to Inspect all air vents and cooling slots to locate the nearest Champion Power ensure that they are clean and unobstructed. Equipment certified service dealer for your Auger/Post Hole Digger or engine maintenance needs.

Every 8 hours or daily Check oil level Clean around air intake and muffler First 5 Hours Change oil Every 50 hours or every season Clean air filter Change oil if operating in hot environments

Every 100 hours or every season Change oil Clean/Adjust spark plug Check/Adjust valve clearance * Clean spark arrester Clean fuel tank and filter * Every 3 years Replace fuel line

* To be performed by knowledgeable, experienced owners or Champion Power Equipment certified service dealers

Rev 90034-20090416 13 Storage

Storage

Engine Storage Engines stored for over 30 days need to be drained of fuel to prevent gum from forming in the fuel system, carburetor components and hoses. For long term storage, please follow these guidelines.

1. Allow the engine to cool completely before storage. 2. Clean the engine according to the instructions in the Maintenance section. 3. Drain all fuel completely from the fuel line and carburetor to prevent gum from forming. 4. Add a fuel stabilizer into the fuel tank. 5. Change the oil. 6. Remove the spark plug and pour about ½ ounce of oil into the cylinder. Crank the engine slowly to distribute the oil and lubricate the cylinder. 7. Reattach the spark plug.

14 Rev 90034-20090416 Specifications

Specifications

Auger/Post Hole Digger Specifications

Engine 270cc, OHV, 4 stroke Hydraulic Tank Capacity 3.9 gal (15L) Hydraulic Motor Torque 3800 in-lb Hydraulic Motor Speed 55 RPM Hydraulic Fluid Type 10W AW32, ASLE H- 150, ISO 32 Pressure Relief Setting 2000 psi Max Flow Capacity 3 GPM Tire Size 15 inches (38 cm) Coupler Ball Size 2 inches (5 cm) Max Towing Speed 45 MPH

Overall Dimensions Weight 350 lb. (158.75 kg) Height 61 inches (154.94 cm) Width 41 inches (104.14 cm) Length 115 inches (292.1 cm)

Hydraulic Oil Oil capacity is 3.9 gallons (15L). Use types 10W AW32, ASLE H-150, and ISO32

Rev 90034-20090416 15 Specifications

Auger/Post Hole Digger Parts Diagram

16 Rev 90034-20090416 Specifications

Auger/Post Hole Digger Parts List Item Part Number Description Qty 1 90034001 Engine 1 2 90034002 Wire Loom 1 3 90034003 Engine Bushing 1 4 90034004 Flat Key 1 5 90034005 Engine Coupling 1 6 90034006 Gear Pump Stand 1 7 90034007 Flat Washer Ø8 11 8 90034008 Lock Washer Ø8 12 9 90034009 Hex Bolt 5/16”-24x1”L 4 10 90034010 Screw M6x10 1 11 90034011 Gear Pump of Coupling 1 12 90034012 Round-head Key 1 13 90034013 Hydraulic Hose 2400 1 14 90034014 Outlet Connector of Pump 1 15 90034015 Gear Pump 1 16 90034016 Lock Nut M8 7 17 90034017 Bolt M8x25 4 18 90034018 Hex Bolt M8x30 4 19 90034019 Nut M10 14 20 90034020 Lock Washer Ø10 14 21 90034021 Flat Washer Ø10 15 22 90034022 Engine Mount Plate 1 23 90034023 Bolt M10x40 4 24 90034024 Screw M4x12 1 25 90034025 Oil Cap 1 26 90034026 Sponge 1 27 90034027 Inside Bushing 1 28 90034028 Breather Cap 1 29 90034029 Flat Washer Ø4 1 30 90034030 Lock Washer Ø4 1 31 90034031 Nut M4 1 32 90034032 Nylon Lock Nut M20 2 33 90034033 Oil Tank 1 34 90034034 Nylon Lock Nut M12 7 35 90034035 Flat Washer Ø12 4 36 90034036 2” Hitch Coupler 1 37 90034037 Bolt M12x80 2 38 90034038 Bolt M12x45 3 39 90034039 Frame Assembly 1 40 90034040 Nut M20 2 41 90034041 Blot M20x60 2 42 90034042 Lock Washer Ø20 2 43 90034043 Clamp Ø30 2 44 90034044 Oil Pipe 1 45 90034045 Outlet Connector Z3/4-Ø25 1 46 90034046 Connector Z3/4” 1 47 90034047 Flat Washer Ø6 8 48 90034048 Bolt M6x20 8 49 90034049 Lock Washer Ø6 8 50 90034050 Filter Plate 1 51 90034051 Rubber Washer 1 52 90034052 Filter 1 53 90034053 Hydraulic Hose 2550 1 54 90034054 Connector Z3/4”-M14x1.5 1 55 90034055 Hydraulic Filter Assemble 1 56 90034056 Connector Z3/4”-Z3/4” 1 57 90034057 Seal 2 58 90034058 Bearing 4

Rev 90034-20090416 17 Specifications

Item Part Number Description Qty 59 90034059 Flange 2 60 90034060 Flat Washer Ø20 2 61 90034061 Slotted Nut M20x1.5 2 62 90034062 Cotter Pin Ø4x30 2 63 90034063 Axle Cap 2 64 90034064 Wheel 2 65 90034065 Bolt M12x1.25x25 8 66 90034066 Flange Bolt M10x35 6 67 90034067 Hydraulic Hose 600 1 68 90034068 Connector Z1/2”-M14x1.5 2 69 90034069 Connect Bushing Z3/4”-Z1/2” 2 70 90034070 Connector Z1/2”-M14X1.5 2 71 90034071 Hydraulic Hose 850 1 72 90034072 Linkage Assembly 1 73 90034073 Nut M6 4 74 90034074 Flexible Joint 1 75 90034075 Screw M8x45 3 76 90034076 Control Valve 1 77 90034077 Hydraulic Hose 850 1 78 90034078 Trigger Assembly 1 79 90034079 Combination Washer Ø18 2 80 90034080 Hydraulic Motor 1 81 90034081 Cotter Pin Ø2x10 1 82 90034082 Handle Grip 1 83 90034083 Motor Coupler 1 84 90034084 Square Washer 1 85 90034085 Screw M8x25 1 86 90034086 Motor Pivot Bracket 1 87 90034087 Connector M18x1.5-M18x1.5 2 88 90034088 Lock Pin Ø10x65 2 89 90034089 Connector M14x1.5-M14x1.5 2 90 90034090 Hydraulic Hose 600 1 91 90034091 Switch 1 92 90034092 Hitch Pin 1 93 90034093 Handle Assembly 1 94 90034094 Towing Chains 2 95 90034095 Auger Coupler 1 96 90034096 Auger Bit 1 97 90034097 Pin A5x28 1 98 90034098 Bolt M12x30 2 99 90034099 Bolt M10x50 4 100 90034100 Hose Retaining Bracket 1 101 90034101 Bolt M10x35 1 102 90034102 Boom 1 103 90034103 Nylon Lock Nut M10 5 104 90034104 Oil Tank Block 4 105 90034105 Big Flat Washer Ø10 4 106 90034106 Engine Block 4 107 90034107 Tapping Screw ST4.8x9.8 4 108 90034108 Connector Cover 1 109 90034109 Oil Scale 1 110 90034110 Oil Plug 1

18 Rev 90034-20090416 Specifications

Engine Parts Diagram

Rev 90034-20090416 19 Specifications

Engine Parts List

Item Parts Number Description Qty 1 ST160F-1070100H Fuel Tank Cap 1 2 ST160F-1070006 Fuel Filter 1 3 ST173F-1070200-E Fuel Tank 1 4 ST160F-1070300-A Fuel Tank Joint 1 5 ST188FD-1070006A Clip 2 6 ST173F-1070001 Tube 1 7 GB41-N-8 Nut M8 5 8 GB5789-FB8-25 Flange Bolt M8×25 2 9 ST160F-1030001-C Oil Filler Cap 1 10 ST160F-1030002 Oil Filler Cap Packing 2 11 GB5789-FB8-40 Flange Bolt M8×40 7 12 ST173F-1030200 Oil Seal 2 13 ST173F-1030011 Crankcase Cover 1 14 ST188F-1030001-B Oil Filler Cap 1 15 ST188F-1020003 Head Cover Packing 1 16 ST188F-1020100 Head Cover 1 17 ST188F-1020006 Head Cover Bolt 1 18 ST173F-1020001 Tube 1 19 ST188FD-1100001 Muffler Gasket 1 20 ST188F-1100002 Exhaust Pipe 1 21 ST188F-1100100 Muffler Gasket 1 22 ST173F-1101200 Muffler 1 23 GB823-88 Tapping Screen M5×10 4 24 ST173F-1101101-A Muffler Protector 1 25 ST168F-1040027 Pivot Bolt 2 26 ST177F-1040021 Rocker Axis 1 27 ST177F-1040028 Push Rod Guide Plate 1 28 ST177F-1040026 Pillow Block 1 29 ST177F-1040022 Rocker Arm 2 30 GB41-N-6 Nut M6 4 31 ST173F-1090100-A Air Cleaner Elbow Comp 1 32 ST173F-1090001 Elbow Packing 1 33 ST173F-1090002 Silencer 1 34 ST173F-1090200 Air Cleaner Element 1 35 ST173F-1090003-A Air Cleaner Cover 1 36 ST160F-1090001 Air Cleaner Cover Nut 1 37 ST173F-1110002 Governor Rod 1 38 ST188F-1110001 Throttle Return Spring 1 39 ST173F-1080200 Control Assembly 1 40 ST188F-1110005 Washer 8.2×17×0.8 1 41 ST188F-1110007 Pin Clip 1 42 ST173F-1110003 Cover Arm Shaft 1 43 ST173F-1110006 Governor Arm 1 44 ST160F-1110004 Governor Arm Bolt 1 45 ST173F-1110004 Governor Spring 1 46 GB5789-FB6-8 Flange Bolt M6×8 6 47 ST173F-1060100-B Recoil Starter Case 1 48 ST188F-1060009 Starter Return Spring 1 49 ST173F-1060008 Recoil Starter Pulley 1 50 ST160F-1061200 Recoil Starter Knob 1 51 ST188F-1060004 Ratchet Guide Spring 1 52 ST188F-1060006 Return Spring 2 53 ST188F-1060007 Recoil Starter Rope 1 54 ST188F-1060005 Starter Ratchet 2 55 ST188F-1060003 Ratchet Guide 1 56 ST188F-1060002 Ratchet Guide Bolt 1

20 Specifications

Item Parts Number Description Qty 57 GB5789-FB6-12 Flange Bolt M6×12 9 58 ST173F-1080100 Fan Cover 1 59 139-FMD-1009301 Rubber Plug 1 60 ST173F-1050200 Connecting Rod Comp 1 61 ST168F-1050004 Piston Pin Clip 2 62 ST173F-1050005 Piston Pin 1 63 ST177F-1050001 Piston 1 ST177F-1050100 Oil Ring Set 1 64 ST177F-1050003 Second Ring Set 1 ST177F-1050002 First Ring Set 1 65 ST173F-1040011 Exhaust Valve 1 66 ST173F-1040003 Intake Valve 1 67 ST188F-1040006 Valve Spring Washer 1 68 ST188F-1040004 Valve Oil Seal 1 69 ST188F-1040007 Valve Spring 2 70 ST188F-1040008 Exhaust Valve Spring Retainer 1 71 ST188F-1040002 Intake Valve Spring Retainer 1 72 ST188F-1040009 Valve Rotator 1 73 ST188F-1010001 Exhaust Stud 2 74 GB41-N-8 Nut M8 2 75 ST173F-1080001 Shroud 1 76 ST173F-1011000-A Cylinder Head 1 77 ST173F-1010002 Bolt 2 78 ST160F-1124000 Spark Plug 1 79 ST173F-1130001 Carburetor Insulator Packing 1 80 ST173F-1130002 Carburetor Insulator 1 81 ST173F-1130003 Carburetor Packing 1 82 ST177F-1131000 Carburetor 1 83 ST188F-1130100 Air Cleaner Packing 1 84 GB5781-B6-29 Bolt M6×29 2 85 ST188F-1122000 Ignition Coil 1 86 ST188F-1030013 Dowel Pin 2 87 ST177F-1040010-II Push Rod 2 88 ST177F-1030008 Cylinder Head Gasket 1 89 ST188F-1040012 Valve Lifter 2 90 ST188F-1030009 Bolt 4 91 139FMD-1003101 Drain Plug Bolt 2 92 139FMD-1003102 Drain Plug Washer 2 93 ST160F-1110108 Governor Washer 1 94 ST173F-1110101 Governor Weight Holder 1 95 ST173F-1110103 Governor Weight 2 96 ST188F-1110102 Governor Weight Pin 2 97 ST188F-1110009 Governor Shaft 1 98 ST188F-1110008 Governor Slider 1 99 ST173F-1050301Q Crankshaft Comp 1 100 ST188F-1050304 Key 1 101 ST188F-1041000 Camshaft Comp 1 102 ST188F-1127000-A Oil Level Switch 1 103 GB276-BB-6206-UU Radial Ball Bearing 6206 Unsealed 2 104 ST173F-1030010 Case Cover Packing 1 105 139FMD-1003003 Dowel Pin 8×14 2 106 ST160F-1128000 Diode Comp 1 107 ST168F-1121100-C Switch 1 108 ST177F-1030006 Crankcase 1 109 ST188F-1030012 Packing 1 110 ST173F-1121000 Flywheel 1 111 ST173F-1080002 Cooling Fan 1 112 ST173F-1060001 Starter Pulley 1 113 ST188F-1050006 Flywheel Nut 1 114 ST188F-1080004-D Diode Base Comp 1

Rev 90034-20090416 21 Specifications

Item Parts Number Description Qty 115 ST168F-1090100 Air Cleaner Cover Nut 1 116 GB97.1-85 Gasket ø6 2 117 ST160F-1040025 Pivot Adjusting Nut 2 118 ST160F-1040024 Rocker Arm Bolt 2 119 ST173F-1071000-E Fuel Meter Assembly 1

22 Specifications

Troubleshooting

Problem Cause Solution Engine will not start No fuel Add fuel Faulty spark plug Replace spark plug Unit loaded during start up Remove load from unit Engine will not start; Low oil level Fill crankcase to the proper level Engine starts but runs roughly Make sure Auger/Post Hole Digger is on a flat, level surface Choke in the wrong position. Adjust choke. Spark plug wire loose Attach wire to spark plug Engine shuts down during operation Out of fuel Fill fuel tank Low oil level Fill crankcase to the proper level. Make sure Auger/Post Hole Digger is on a flat, level surface Engine cannot supply enough power Insufficient ventilation Check for air restriction. Move to a or overheating well ventilated area Engine gallops Engine governor defective Contact the help line

Rev 90034-20090416 23 Warranty

system cleaning and obstruction due to buildup is Warranty not covered by this warranty. CHAMPION POWER EQUIPMENT Other Exclusions 1 YEAR LIMITED WARRANTY Effective September 1, 2006. Replaces all undated This warranty excludes: warranties and all warranties dated before September 1, Cosmetic defects such as paint, decals, etc. 2006. Wear items such as filter elements, o-rings, etc. Accessory parts such as starting batteries, and Warranty Qualifications storage covers. Champion Power Equipment (CPE) will register Failures due to acts of God and other force this warranty upon receipt of your Warranty majeure events beyond the manufacturer’s Registration Card and a copy of your sales receipt control. from one of CPE's retail locations as proof of Problems cause by parts that are not original purchase. Champion Power Equipment parts. Please submit your warranty registration and your proof of purchase within ten (10) days of the Limits of Implied Warranty and date of purchase. Consequential Damage Repair/Replacement Warranty Champion Power Equipment disclaims any obligation to cover any loss of time, use of this CPE warrants to the original purchaser that the product, freight, or any incidental or mechanical and electrical components will be free consequential claim by anyone from using this of defects in material and workmanship for a Auger/Post Hole Digger. THIS WARRANTY IS period of one (1) year from the original date of IN LIEU OF ALL OTHER WARRANTIES, purchase (90 days for commercial & industrial EXPRESS OR IMPLIED, INCLUDING use). Transportation charges on product WARRANTIES OF MERCHANTABILITY OR submitted for repair or replacement under this FITNESS FOR A PARTICULAR PURPOSE warranty are the sole responsibility of the purchaser. This warranty only applies to the A unit provided as an exchange will be subject to original purchaser and is not transferable. the warranty of the original unit. The length of the warranty governing the exchanged unit will Do not return the unit to the place of remain calculated by reference to the purchase purchase date of the original unit. Contact CPE's Technical Service and CPE will troubleshoot any issue via phone or e-mail. If the This warranty gives you certain legal rights which problem is not corrected by this method, CPE may change from state to state. Your state may will, at its option, authorize evaluation, repair or also have other rights you may be entitled to that replacement of the defective part or component are not listed within this warranty. at a CPE Service Center. CPE will provide you with a case number for warranty service. Please Contact Information keep it for future reference. Repairs or replacements without prior authorization, or at Address an unauthorized repair facility, will not be Champion Power Equipment, Inc. covered by this warranty. Customer Service Warranty Exclusions 10006 Santa Fe Springs Rd. Santa Fe Springs, CA 90670 This warranty does not cover the following repairs and equipment: Customer Service Normal Wear Mon – Fri 8:30 AM – 5:00 PM (PST/PDT) Toll Free: 1-877-338-0999 Auger/Post Hole Digger needs periodic parts and Fax no.: 1-562-236-9429 service to perform well. This warranty does not cover repair when normal use has exhausted the Technical Service life of a part or the equipment as a whole. Mon – Fri 8:30 AM – 5:00 PM (PST/PDT) Installation, Use and Maintenance Toll Free: 1-877-338-0999 [email protected] This warranty will not apply to parts and/or labor if this Auger/Post Hole Digger is deemed to have been misused, neglected, involved in an accident, abused, loaded beyond its limits, modified, and installed improperly. Normal maintenance such as spark plugs, air filters, adjustments, fuel

24 Rev 90034-20090416 Notes

Notes

Rev 90034-20090416 25