Sliding Bevel Square.Pdf

Total Page：16

File Type：pdf, Size：1020Kb

Project from www.craftsmanspace.com Sliding bevel square plan 1 Sliding bevel square Here you can find a plan according to which you can make a sliding bevel square which can also be found under the name sliding T-bevel. The Sliding bevel square is in reality a try-square with movable blade. The sliding T-bevel is, both for its purpose and appearance, essentially similar to the bevel square tool, the only difference is that the blade protrudes from both sides of the stock so that two angles are available. If the angle on one side is 45°, then it is 135° on the other. The sliding T- bevel serves to mark lines at an angle or to check angles. Sliding T bevel square may be set at any desired angle. Sliding T bevel consists of a stock (or handle) and a slotted blade (or tongue) that pivots on a machine screw with wing nut. The blade may be fixed firmly at any desired angle by simply turning the wing nut (or knurled screw). Use the dimensions in the plan as guidance; in case you need some dimensions that are different from those given in our plan, simply adjust the sliding T- bevel to the dimensions that suit you. How to use: The best method of setting sliding T bevel is to lay it on the protractor and then set and fix it at the required angle. This tool is used for: - checking whether the angle between two surfaces is the same everywhere; - marking out any angle other than an angle of 90° (for which the try square is used); - checking all angles except an angle of 90°(for which the try square is used). The blade can be made either of wood or of metal, but if you want a quality and long lasting sliding T- bevel, it is better to use metal for the blade and hardwood for the stock. Project from www.craftsmanspace.com Sliding bevel square plan 2 Parts list Project from www.craftsmanspace.com Sliding bevel square plan 3 Assembly drawing Project from www.craftsmanspace.com Sliding bevel square plan 4 Project from www.craftsmanspace.com Sliding bevel square plan 5 Project from www.craftsmanspace.com Sliding bevel square plan 6 Standard parts Assemblage images 1 2 .

Copy Link

Recommended publications

Extra Long Screwdriver Bits Kit Box Tool Holders
EXTRA LONG PHILLIPS® EXTRA LONG BITS 150MM 150mm long Phillips® screwdriver bits in three SCREWDRIVER BITS sizes No.1, 2 and 3. Bit Size Order Ref. Price EXTRA LONG TORX® EXTRA LONG POZI® Phillips® No. 1 SNAP/PH/1A £5.00 BITS 150MM BITS 150MM Phillips® No. 2 SNAP/PH/2A £5.00 Phillips® No. 3 SNAP/PH/3A £5.00 150mm long Torx® screw driver bits with round 150mm long Pozi® Screwdriver bits in three shafts. Can be used with T-Star® screws. sizes No.1, 2 and 3. EXTRA LONG Bit Size Machine Screw Order Ref. Price Bit Size Order Ref. Price SQUARE DRIVE BITS ® ® Torx T10 M3 SNAP/TX/10A £5.00 Pozi No. 1 SNAP/PZ/1A £5.00 Two lengths of No.2 Robertson square drive Torx® T15 M3.5 SNAP/TX/15A £5.00 Pozi® No. 2 SNAP/PZ/2A £5.00 bits. 75mm (3”) and 150mm (6”) for use with Torx® T20 M4 SNAP/TX/20A £5.00 Pozi® No. 3 SNAP/PZ/3A £6.00 Pocket Hole Jig. Torx® T25 M5 SNAP/TX/25A £5.00 Bit Size Order Ref. Price Torx® T30 M6 SNAP/TX/30A £5.00 Robertson® No. 2 (3”) SNAP/SQ/2A £4.00 Robertson® No. 2 (6”) SNAP/SQ/2B £5.00 KIT BOX 19 PIECE METRIC KIT BOX Standard Quick Chuck 1, 2, 3, 4, 5, 7 and 7mm drills. No.6, 8 and 10 drill bit guide. No. 4, 6, 8, 10 and 12 drill countersinks and Pozi® No.1, 2 and 3 50mm screwdriver bits.
[Show full text]
1. Hand Tools 3. Related Tools 4. Chisels 5. Hammer 6. Saw Terminology 7. Pliers Introduction
1 1. Hand Tools 2. Types 2.1 Hand tools 2.2 Hammer Drill 2.3 Rotary hammer drill 2.4 Cordless drills 2.5 Drill press 2.6 Geared head drill 2.7 Radial arm drill 2.8 Mill drill 3. Related tools 4. Chisels 4.1. Types 4.1.1 Woodworking chisels 4.1.1.1 Lathe tools 4.2 Metalworking chisels 4.2.1 Cold chisel 4.2.2 Hardy chisel 4.3 Stone chisels 4.4 Masonry chisels 4.4.1 Joint chisel 5. Hammer 5.1 Basic design and variations 5.2 The physics of hammering 5.2.1 Hammer as a force amplifier 5.2.2 Effect of the head's mass 5.2.3 Effect of the handle 5.3 War hammers 5.4 Symbolic hammers 6. Saw terminology 6.1 Types of saws 6.1.1 Hand saws 6.1.2. Back saws 6.1.3 Mechanically powered saws 6.1.4. Circular blade saws 6.1.5. Reciprocating blade saws 6.1.6..Continuous band 6.2. Types of saw blades and the cuts they make 6.3. Materials used for saws 7. Pliers Introduction 7.1. Design 7.2.Common types 7.2.1 Gripping pliers (used to improve grip) 7.2 2.Cutting pliers (used to sever or pinch off) 2 7.2.3 Crimping pliers 7.2.4 Rotational pliers 8. Common wrenches / spanners 8.1 Other general wrenches / spanners 8.2. Spe cialized wrenches / spanners 8.3. Spanners in popular culture 9. Hacksaw, surface plate, surface gauge, , vee-block, files 10.
[Show full text]
Punching Tools 
TruServices Punching Tools Order easily – with the correct specifica- tions for the right tool. Have you thought of everything? Machine type Machine number Tool type Dimensions or drawings in a conventional CAD format (e.g. DXF) Sheet thickness Material Quantity Desired delivery date Important ordering specifications ! Please observe the "Important ordering specifications" on each product page as well. Order your punching tools securely and conveniently 24 hours a day, 7 days a week in our E-Shop at: www.trumpf.com/mytrumpf Alternatively, practical inquiry and order forms are available to you in the chapter "Order forms". TRUMPF Werkzeugmaschinen GmbH + Co. KG International Sales Punching Tools Hermann-Dreher-Strasse 20 70839 Gerlingen Germany E-mail: [email protected] Homepage: www.trumpf.com Content Order easily – with the correct specifica- General information tions for the right tool. TRUMPF System All-round Service Industry 4.0 MyTRUMPF 4 Have you thought of everything? Machine type Punching Machine number Classic System MultiTool Tool type Cluster tools MultiUse Dimensions or drawings in a conventional CAD format (e.g. DXF) 12 Sheet thickness Material Cutting Quantity Slitting tool Film slitting tool Desired delivery date MultiShear 44 Important ordering specifications ! Please observe the "Important ordering specifications" on each product page as well. Forming Countersink tool Thread forming tool Extrusion tool Cup tool 58 Marking Order your punching tools securely and conveniently 24 hours a day, 7 days a week in our E-Shop at: Center punch tool Marking tool Engraving tool Embossing tool www.trumpf.com/mytrumpf 100 Alternatively, practical inquiry and order forms are available to you in the chapter "Order forms".
[Show full text]
Practical Woodwork Worksheet 1
Practical Woodwork Worksheet 1 1. Tick () the correct answer. (a) Which man-made board is shiny on one side and textured (rough) on the other? 1 Blockboard Chipboard Plywood Hardboard (b) Which material is made from mixing glue with very small pieces of wood? 1 Acrylic Chipboard Plastic Laminate Plywood 2. Tick () the correct answer. (a) This woodwork joint is called a: 1 Stopped halving Stopped housing Stopped mortise Stopped rebate Practical Woodwork Worksheet 1 Tick () the correct answer. (b) The process used to make this wooden handle is called: 1 Forming Shaping Turning Twisting 3. Four woodwork joints are shown: (a) Which joint would be most likely to be used to join a rail to a leg of a table? 1 (b) Which joint would be most likely to be used to join a shelf to a side of a cabinet? 1 4. Tick () the correct use for each tool. (a) Boring holes in metal Boring holes in wood 1 Countersinking screw holes Cutting threads in metal. Practical Woodwork Worksheet 1 Tick () the correct use for each tool. (b) 1 Bending a piece of acrylic Hammering in nails Forging a piece of metal Driving a chisel into wood 5. Five saws are shown below. (a) Which saw would be used to cut a large sheet of thick plywood? 1 6. Tick () the correct answer. (a) This is used in a: 1 Milling machine Mortise machine Shaping machine Shearing machine Practical Woodwork Worksheet 1 Tick () the correct use for each tool. (b) This is used in a: 1 Drilling machine Sanding machine Metal lathe Wood lathe (c) The frame shown has just been glued.
[Show full text]
Chisel Quilts
1501 Easy Chisel Quilts REQUIRED GO! Baby Friendly Twelve Star Quilt Quilt 49” x 61” Finished Block SizeSize 11½”11½” Teresa Varnes Amie Potter Long Braid Tablee RunneRunnerr 14” x 102” Finished Width ooff BrBraidaid 6” Eleanor Burns Judy Jackson Medium Length Braid Table Runner 14” x 54” 2 Select from a Star Lap Robe or Braid Table Runer in two sizes featuring AccuQuilt® Die #55039 for Chisels. The Star also uses Die #55009 for Half Square Triangles. This die is #3 from the 6” Mix and Match series. The Chisel die cuts two shapes at a time. Chisels #55039 The Half Square Half Square Triangle Triangle die cuts four #55009 shapes at a time. Carefully follow cutting instructions, because they are not the same for both projects. Chisels for Star Lap Robe are cut from strips placed right side up. Chisels for Braid Table Runner are cut from strips placed wrong sides together in pairs. 3 Fabric Selection Decide on the theme or era of your projects, such as Civil War, Depression, Traditional, Modern, Juvenile, or Holiday. It's easy to select from a line that a designer put together in a variety of prints and solids, or ones that appear solid. A total of eighteen fat quar- ters is enough for both projects, including two Table Runners in the medium length. Select twelve medium to dark print fat quarters in a variety of values, colors, and scales. Select six Background prints in similar values but different textures that appear solid and do not distract from prints. Twelve Fat Quarters Six Backgrounds In additional, purchase fabric listed on page 5 for ﬁnishing your project.
[Show full text]
Bandsaw Puzzle Cubes
Bandsaw Puzzle Cubes How’s that scrap pile in the corner of the shop coming along? Getting any smaller? Here’s one way to put some of your cherished chunks of thick stock to good use, producing casual gifts of irresistible appeal to young and old alike. Kids under ten can reassemble these puzzles in 30 seconds, grown-ups in only three or four minutes if they’re sharp. Make sure your bandsaw blade is square to the table, both left & right and fore & aft. The larger the puzzle cube, the less error you can get away with. Kerf width forgives some inaccuracy, but not much. Start off by milling up a cube — any size will do, but bigger is bet- ter: 3” x 3” or 4” x 4” makes a good puzzle blank. Put a 1/8” or 1/16” blade on your bandsaw, and don’t think about any claims you might have seen that you can’t cut thick stock with a very nar- row blade. Cool Blocks™ lateral guides are essential for 1/16”s and mighty useful for controlling 1/8” blades, too. Orient the cube so you’ll start cut- ting across the grain, and cut a ran- domly invented jigsaw puzzle pattern across the block. Make a fairly simple pattern. Push gently, using just your fingertips. Let the saw take its time working throughthe stock, so the blade stays vertical and your curves are consistent throughout.You’ll notice that sawing with the grain is much slower than across it; be ready for significant changes in speed and back pressure as you turn the block.
[Show full text]
2016 Affinity Tool Works Dealer Price Book Rev 20 Xlsx
2016 PRODUCT CATALOG Prices Effective January 1, 2016 Supersedes all previously dated price lists. No. 20 Prices subject to change without notice. Affinity Tool Works, LLC • 1161 Rankin • Troy, Michigan 48083 Ph(248) 588-0395 • Fax(248) 588-0623 • [email protected] • www.affinitytool.com Pkg www.boratool.com Stock No. Description Part No. List Price Qty BORA Clamps & Vises 540445 4.5" Micro Bar Clamp (2-Pack) 6$ 10.91 540606-S 6" Midi Pistol Grip Clamp 6$ 12.64 540606 6" Midi Pistol Grip Clamp (2-Pack) 6$ 23.64 540612-S 12" Midi Pistol Grip Clamp 6$ 15.45 540612 12" Midi Pistol Grip Clamp (2-Pack) 6$ 30.00 540806 6" Pistol Grip Bar Clamp 6$ 19.09 540812 12" Pistol Grip Bar Clamp 6$ 20.91 540818 18" Pistol Grip Bar Clamp 6$ 28.18 540824 24" Pistol Grip Bar Clamp 6$ 30.00 BORA Specialized Clamps & Vises 540520 20 Piece Mini Spring Clamp Set 1$ 10.00 551025 Corner Clamp 6$ 30.00 551027 Large Vise 6$ 30.00 BORA Angle Master Miter Duplicator for Mitersaws 530301 Angle Master - Miter Duplicator 3$ 65.45 BORA Sharpening Stones 501057 Sharpening Stone-Aluminum Oxide 6" x 2" x 1" 30$ 4.47 501098 Sharpening Stone-Green Silicon Oxide 6" x 2" x 1" 30$ 8.73 501060 Sharpening Stone-Aluminum Oxide 8" x 2" x 1" 30 $ 8.90 Page 2 © 2016 Affinity Tool Works, LLC Pkg Stock No. Description List Price Qty BORA Modular Clamp Edge & Accessories 543100 100" WTX Clamp Edge (50" + 50") 6$ 99.00 543050 50" WTX Clamp Edge 6$ 53.00 543036 36" WTX Clamp Edge 6$ 46.00 543024 24" WTX Clamp Edge 6$ 40.00 Kits: 543300 3 pc Clamp Edge Set, 24, 36, 50" 4$ 134.00 543400
[Show full text]
Quick Guide to Precision Measuring Instruments
E4329 Quick Guide to Precision Measuring Instruments Coordinate Measuring Machines Vision Measuring Systems Form Measurement Optical Measuring Sensor Systems Test Equipment and Seismometers Digital Scale and DRO Systems Small Tool Instruments and Data Management Quick Guide to Precision Measuring Instruments Quick Guide to Precision Measuring Instruments 2 CONTENTS Meaning of Symbols 4 Conformance to CE Marking 5 Micrometers 6 Micrometer Heads 10 Internal Micrometers 14 Calipers 16 Height Gages 18 Dial Indicators/Dial Test Indicators 20 Gauge Blocks 24 Laser Scan Micrometers and Laser Indicators 26 Linear Gages 28 Linear Scales 30 Profile Projectors 32 Microscopes 34 Vision Measuring Machines 36 Surftest (Surface Roughness Testers) 38 Contracer (Contour Measuring Instruments) 40 Roundtest (Roundness Measuring Instruments) 42 Hardness Testing Machines 44 Vibration Measuring Instruments 46 Seismic Observation Equipment 48 Coordinate Measuring Machines 50 3 Quick Guide to Precision Measuring Instruments Quick Guide to Precision Measuring Instruments Meaning of Symbols ABSOLUTE Linear Encoder Mitutoyo's technology has realized the absolute position method (absolute method). With this method, you do not have to reset the system to zero after turning it off and then turning it on. The position information recorded on the scale is read every time. The following three types of absolute encoders are available: electrostatic capacitance model, electromagnetic induction model and model combining the electrostatic capacitance and optical methods. These encoders are widely used in a variety of measuring instruments as the length measuring system that can generate highly reliable measurement data. Advantages: 1. No count error occurs even if you move the slider or spindle extremely rapidly. 2. You do not have to reset the system to zero when turning on the system after turning it off*1.
[Show full text]
Great American Furniture
Great american FURNITUREFROM THE EDITORS OF MAGAZINE JULY 2003 SHAKER Classic Candlestand ▼ 6 The Shakers referred to the leg design as “spider feet.” Surprisingly, this traditional form is not that complicated. Press Cupboard ▼ 12 This fine case piece showcases both your collection and craftsmanship. Oohs and ahhs guaranteed. Hand-tool Stepstool ▼ 19 Become a Neanderthal, if only for one project. This attractive yet highly useful stool offers step-by-step hand-tool instruction. 18TH CENTURY 62 Simple Candle Boxes ▼ 24 6 Beginning woodworkers will love this fast, classic project. Butler Tray Table ▼ 28 A Chippendale table, complete with a removable tray top, is just what you need for serving tea and coffee to guests. 12 ▼ Pennsylvania Spice Box 36 An instant heirloom: This beautiful 18th century spice box doubles as the perfect jewelry box for you or your loved one. ARTS & CRAFTS Greene & Greene Side Table ▼ 43 Grace the end of your sofa or chairs with class and style. 28 ▼ Slant-arm Morris Chair 48 Build an Arts & Crafts icon that instantly will become the most sought-after chair in your home. CONTEMPORARY 48 Nicolai Fechin-style Bench ▼ 58 Always wanted to try carving? Here’s your chance. The detail is meant to look rustic and simple so mistakes won’t matter. Plywood Nesting Tables ▼ 66 Sleek and versatile (one table or three), this project is a great lesson in making perfect miter joints. 66 Rice-paper Maple Lamp ▼ 70 Build a simple lamp based on designs typical in a Japanese household that will look great in any modern home.
[Show full text]
Stagecraft 1 -Tools Flashcards | Quizlet
Stagecraft 1 -Tools 123 terms by kj22333 Like this study set? Create a free account to save it. Create a free account Claw hammer framing hammer Tack hammer Ball peen hammer staplegun Self retracting hand tape measure Framing square Try Square Combination Square Speed square Spirit Level Bevel Gauge or Sliding T-Bevel Chalk Line Plumb Bob Trammel Points Hand Saw Back Saw Coping Saw Keyhole Saw Hack Saw Wood Plane Draw knife Wood Rasp File Tin Snips Diagonal Cutters Bolt Cutters Wood Chisel Cold Chisel Utility knife (Mat knife, x-acto knife) Box End Wrench Open Ended Adjustable Wrench (Crescent or C-wrench) Pipe Wrench c-clamp Parallel Jaw Clamp Jorgenson clamp Bar Clamp Crow Bar claw foot Slotted Screw Driver Phillips Screw Driver Portable Circular Saw Power Miter Saw Cordless Drill Jig Saw Router Band Saw Table Saw Straightedge t-square caliper compass miter guide tape measure saw protractor contour gauge scribe cross cut saw wider kerf crosscut saw teeth rip tooth blade/saw dovetail saw carpenters hatchet wire strippers paint scrapper electrical cable cutters sureform rat tail rasp can cut a hole/ shape a hole Racketing brace hand drill auger bit twist bit not very good at removing sawdust pilot bit countersink bit spade bit carbide bit good for concrete and plaster hole saw allen wrench set Yankee screwdriver screws as you push downward hammer staple gun nail set mallet nut driver pipe clamp vice wood vice spring clamp band clamp welding clamp vise grip lineman's pliers channel lock pliers/ slip joint lock pliers crimping tool needle nose pliers slip joint pliers nail puller socket wrench open end wrench pry bar tack remover grommet set rivet gun whetstone hot glue gun tubecutter die holder anvil pipe cutter center punch die tap conduit bender regulator pallet staple gun Nail gun Air ratchet/ grinder radial arm saw steel band saw drill press scew shooter angle grinder palm sander belt/disk sander random orbital sander best sander.
[Show full text]
Introduction to Carpentry Tools and Joints
INTRODUCTION TO CARPENTRY TOOLS 1. Try Square 2. Steel Rule 3. Marking Guage 4. Coping Saw 5. Tenon Saw 6. Penon Saw 7. Ironjack Plane 8. Benchwise 1. Try Square This is used to mark lines at 90 degrees to a straight edge. It is used to mark out lines square to the face edge and face side. It may also be used to check if edges are straight. If the try square is placed on the edge of the material and held up to a light, any light shining through between the material and the try square blade indicates that the edge of the material is not straight. 2. Steel Rule A steel rule is a very accurate marking and measuring tool. The steel is thin and the markings on the rule are very fine. The measurements are in millimetres on one edge and inches on the other. The steel rule can also be used as a straight edge to check if materials or edges of materials are straight. The measurements on the steel rule go all the way to the end unlike the plastic ruler. This is because the rule may be used to measure inside pipes. It may also be used to measure diameters and circumferences of pipes and tubes accurately. The end of the rule with the measurements to the edge is called the zero end. By: Harish Gupta Page 1 3. Marking Guage The marking gauge is used on wood.It is used to mark straight lines parallel to a straight edge.The marking tool has an adjustable stock (the stock slides up and down the stem) and is set using a steel rule.
[Show full text]
FED 101-026: Fundamentals of Engineering Design
New Jersey Institute of Technology Digital Commons @ NJIT Mechanical and Industrial Engineering Syllabi NJIT Syllabi Spring 2021 FED 101-026: Fundamentals of Engineering Design Balraj Mani Follow this and additional works at: https://digitalcommons.njit.edu/mie-syllabi Recommended Citation Mani, Balraj, "FED 101-026: Fundamentals of Engineering Design" (2021). Mechanical and Industrial Engineering Syllabi. 277. https://digitalcommons.njit.edu/mie-syllabi/277 This Syllabus is brought to you for free and open access by the NJIT Syllabi at Digital Commons @ NJIT. It has been accepted for inclusion in Mechanical and Industrial Engineering Syllabi by an authorized administrator of Digital Commons @ NJIT. For more information, please contact [email protected]. ME - FUNDAMENTALS OF ENGINEERING DESIGN FED 101 - ME TRACK January 19, 2021 Spring 2021 COURSE ADMINISTRATIVE INFORMATION Course Name: ME – FUNDAMENTALS OF ENGINEERING DESIGN Course Number: FED 101-026 (12827) Class meeting Room: Asynchronous Mode – via WebEX After Class office room: By appointment - WebEX Instructor’s Name: B. S. Mani Instructor’s Téléphone: (973) 596-3339 (office) (630) 345-0558 (mobile - text and dial) Instructor’s e-mail id: [email protected] Class meeting hours: Friday, 07:30AM–10:20 AM (Friday :L60, R: L61) After Class office hours: Open time slots by appointment-WebEX Complaints / Compliments: Dr. Joga Rao (973) 596-5601 [email protected] COURSE DESCRIPTION Study technical graphics and the computer as a technical drawing tool; Introduction to projections and multiview drawings and visualization; Discuss geometry commonly used in engineering design graphics, orthographic projections; Dimensioning techniques, tolerancing and introduction to auxiliary and sectional views; Apply software program Creo Parametric 6.0 (previously known as Pro/Engineer/Wildfire) to various problems.
[Show full text]