Ginko Wrap Bracelet Try using the new Matubo Ginko in this beginner-friendly project

Material (for one bracelet)

Matubo Ginko (approx. 12 pcs) Matubo Rulla (approx. 7 pcs) Pinch beads (approx. 12 pcs) Matubo 11/0 (or 11/0 Japanese seed beads) (approx. 30 pcs) 15/0 Japanese seed beads (approx. 60 pcs)

Beading wire, crimp beads (2pcs), tips (2pcs), (3pcs), a clasp (1pc).

(This amount of material will give you a bracelet that is approximately 19cm/7.4in long - including the clasp.)

Difficulty: For beginners

1 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz) Autorem tohoto designu a návodu je Nela Kábelová (www.gianelle.beadforum.cz) www.matubobeads.com 1) Cut two pieces of 5) Then use the flat-nose beading wire (I usually use to close the bead tip. 0,015-inch diameter for this kind of bracelets).

Both pieces should be a little longer than the desired length of the bracelet. 6) Start stringing beads on You can also use double or triple that length and create the opposite end of the a wrap-style bracelet, that is – as the name suggests – wire. worn wrapped multiple times around your wrist (like the First, string three 15/0s -brown bracelet on the front page). and one 11/0 on each end.

2) On both pieces of wire string a bead tip (closed side first) and then one 7) Then add one Rulla (one crimp bead. end of the wire through each hole).

3) Move the crimp bead to the end of both wires and then squeeze it with flat- 8) Then one 11/0 and one nose pliers, so it becomes 15/0 on each end. flat.

4) Then pull the bead tip over the crimp bead (the bead goes inside the bead 9) Then one Ginko (one end tip). of the wire through each hole, from the "outside").

2 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz) Autorem tohoto designu a návodu je Nela Kábelová (www.gianelle.beadforum.cz) www.matubobeads.com 10) Then one 15/0, one 15) Take another bead tip pinch bead and one 15/0 on and string it on both ends each end. of the wire (closed side first), then string a crimp bead.

11) Then one Ginko (one 16) Move both components end of the wire through as close to the beads as each hole, from the possible and then squeeze "inside"). the crimp bead with flat- nose pliers. Then cut the excess of the beading wire and then close the bead tip with the crimp bead inside.

12) Then one 15/0 and one 17) This is what you should 11/0 on each end. get.

13) This is what you should 18) Use jump rings to attach get. Repeat steps 7-12, until a clasp of your choice. you reach the desired length.

14) You should finish the 19) The bracelet is finished. bracelet with a Rulla bead and then one 11/0 and three 15/0s on each end.

3 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz) Autorem tohoto designu a návodu je Nela Kábelová (www.gianelle.beadforum.cz) www.matubobeads.com Colorways:

Matubo Ginko 03000/29123 Matubo Rulla 93200/85001 Pinch beads 02010/01750 Matubo 11/0 23980/14415 TOHO 15/0 83 Metallic Iris Brown

Matubo Ginko 23980/29503 Matubo Rulla 33050/85001 Pinch beads 00030/98544 Miyuki 11/0 4202 Duracoat Galvanized Miyuki 15/0 135FR Matte Brown AB

Matubo Ginko 00030/15695 Matubo Rulla 63130/43400 Pinch beads 63130 Matubo 11/0 23980/14415 TOHO 15/0 83 Metallic Iris Brown

Matubo Ginko 03000/86805 Matubo Rulla 63130/85001 Pinch beads 00030/84110/14464 Matubo 11/0 00030/01670 TOHO 15/0 2604F Semi Glazed Turquoise

4 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz) Autorem tohoto designu a návodu je Nela Kábelová (www.gianelle.beadforum.cz) www.matubobeads.com