DOCSLIB.ORG

Oxygen Generation. by Vacuum Pressure Swing Adsorption

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Oxygen Generation. by Vacuum Pressure Swing Adsorption Oxygen generation. By Vacuum Pressure Swing Adsorption. Vacuum Pressure Swing Adsorption (VPSA) plant in Italy. Oxygen generation 03 Sulfur recovery plants have increased capacity The steelmaking process requires oxygen. through oxygen enrichment. Proven technology – tailored to your needs. Fast, cost-effective oxygen on demand Advantages. Balancing performance needs with cost constraints. Demand for on-site oxygen generation solutions continues to rise across a number of industries. Vacuum Pressure Swing Adsorption Our entire VPSA offering is geared towards ensuring the perfect fit for (VPSA) technology is an increasingly popular way ofmeeting this individual application needs. You can rely on our VPSA specialists to demand. VPSA involves separating air into its constituent components recommend the configuration that strikes the best balance between by means of adsorption. In other words, the gas molecules bind with your performance needs and investment constraints. With a VPSA adsorbent material at different rates depending on the pressure. This system from Linde, you can look forward to the following benefits: allows operators to single out one particular gas from air. The growth in demand for VPSAtechnology is largely attributable to its simplicity, Right volume and purity on demand reliability and low operating costs. Scaling from 50 to 10,000 Nm³/h (2 to 342 tpd) with purity levels of up to 95 vol.% our plants deliver the precise volume and purity you need – on demand. Experience counts Outstanding availability World leader in adsorption technology, Linde has designed and Offering exceptional availability rates of almost 100%, all of our supplied more than 700 adsorption plants worldwide – including the plants are engineered for excellence, featuring premium components world‘s largest units. We also offer the highest availability levels in the to ensure maximum operational uptime. industry. Our adsorption systems are therefore the solution of choice where performance, flexibility, availability and reliability are key Low operating costs success factors. High quality and easy accessibility to all components Our VPSA units are designed for the highest levels of energy efficiency, also ensure ease of maintenance. making them a cost-effective option. Ease of maintenance and automated operations further reduce operating costs. A PLC-based control system dynamically adjusts the VPSA process to meet changing Adsorption applications purity and flow needs. Major applications include the recovery of high purity hydrogen, Advanced flexibility methane and carbon dioxide as well as the generation of oxygen and Operational capacity can be easily adjusted to the required levels – nitrogen. Linde oxygen VPSA systems are successfully deployed in anything from 0% to 100% is possible. Our plants also start up at the industries as diverse as iron and steel, metals, mining, chemicals, pulp push of a button and are operational within a few minutes. Shut-down and paper, water treatment, glass, food and fish farming. is also completed within minutes. Remote control Large portfolio for all capacity needs To increase manageability even further, our VPSA systems come with an optional dedicated port that can be connected to a plant-wide Our VPSA units for oxygen generation come in multiple sizes and control system (DCS) and/or a communication board for remote control. shapes to suit individual needs. All systems support on-stream applications requiring gaseous oxygen with purity levels of up to 95%. Modular design and prefabricated equipment Capacities scale up to 10,000 Nm³/h (342 tpd) – with one single train. Prefabrication of VPSA modules accelerates deployment, reduces installation effort and saves costs. For instance, our valve skids – In addition, we have developed a fully containerised C-series containing switching and control valves, instrumentation and piping – supporting oxygen streams of up to 2,000 Nm³/h (68 tpd). are preassembled and tested prior to delivery. Our specially designed This C-series is ideal for customers looking to combine the containerised C-series takes mobility, time efficiencies and cost benefits of rapid deployment with maximum cost efficiencies. savings to the next level. 04 Oxygen generation VPSA in detail. How Vacuum Pressure Swing Adsorption works. Process description Each adsorber undergoes a cyclic process, Before the adsorbent is fully saturated with consisting of: nitrogen, the system switches over to the Use of adsorption to recover gases is based → Adsorption (O₂ production) other bed in order to regenerate the saturated on the ability of certain porous materials → Desorption (evacuation) adsorber. to adsorb gases through their large surface → Re-pressurisation (pressure build-up) areas. Individual gases are adsorbed to Desorption different extents depending on the pressure While the first adsorber is in adsorption stage, and temperature of the feed gas and the Adsorption and regeneration cycles the second bed (B) is regenerated by opening selectivity of the adsorbent (see figure 1). the residual gas valve, which is connected to a A VPSA plant is often designed as “2-bed vacuum pump. This pump draws out moisture, Adsorptive air separation is a periodic system”. One bed is in the adsorption stage carbon dioxide and nitrogen in the opposite batch process, in which adsorbent material and the other in the regeneration stage direction to the gas flow in adsorption mode. is alternately (see figure 2). This residual gas is vented to the atmosphere. 1. fed with pressurised air to produce the Adsorption Re-pressurisation required product, and The vessel (A) in the adsorption phase is fed In order to reduce energy consumption during 2. regenerated by vacuum to remove the with compressed process air through an open pressurisation of the regenerated adsorber, residual gases from the adsorbent. air valve. dry gas from the pressurised adsorber (A) flows to the evacuated adsorber (B). To During the generation of oxygen, a cyclic Moisture and carbon dioxide are captured at increase pressure further, the process air swing between overpressure and vacuum the entrance zone of the adsorber. Nitrogen blower pressurises ambient air and feeds it occurs (Vacuum Pressure Swing Adsorption). molecules are continuously adsorbed, thus into the adsorber (B). To reduce energy consumption, the pressure separating oxygen molecules from nitrogen is equalised between the production molecules. At the discharge side of the And so the cycle continues. (overpressure) and regeneration (vacuum) adsorber, the dry oxygen flows into the buffer steps. vessel. Figure 1: Ranking of adsorption forces Figure 2: Typical process flow diagram of a Linde oxygen VPSA plant Compressed air Oxygen Residual gas Hydrogen weak Oxygen Argon Nitrogen VPSA O2 buffer Carbon monoxide Methane Oxygen Carbon dioxide Adsorber A Residual gas Ethane to atmosphere Ethylene Propane Butane Adsorber B Propylene Air Silencer Ammonia compressor Air Hydrogen sulfide Mercaptanes BTX Water strong Vacuum pump Oxygen generation 05 Containerised VPSA. A prefabricated solution for accelerated deployment and reduced costs. Figure 3: 3D graphic of a containerised VPSA plant 7 7 5 1 3 6 2 4 3 8 1 Machinery container 2 Valve skid container 3 Adsorption vessels 4 Interconnecting piping 5 Electrical container 6 Oxygen product gas compressor package (optional) 7 Utility container (optional) 8 Buffer vessel Our C-series “containerised” VPSA plants 4 Interconnecting piping “Understanding our are designed as highly prefabricated, The interconnecting piping between customers' needs, offering modularised and cost-effective facilities. the machinery container, adsorber a value-creating solution The main equipment of the VPSA plant, i.e. vessels, valve skid container and oxygen the air blower and vacuum pump package, compressor is delivered prefabricated for and executing are the valve skid and the electrical system, are the installation on site. key capabilities at supplied fully assembled inside hoods or Linde Engineering.” tailor-made containers. Expenses for erection 5 Electrical container and commissioning of the highly modularised Including PLC control system, electrical Jürgen Nowicki C-series VPSA plant are significantly reduced switchgears and Motor Control Centre Managing Director Member of the Board of Directors with this solution. Due to the containerised (MCC). Linde Engineering Division design of the C-series, a separate machinery building is not required. 6 Oxygen product gas compressor package (optional) 1 Machinery container Including motor, coolers, pulsation Including rotary-lobe-type air blower unit dampers, valves and instrumentation. and vacuum pump unit with motors, cooler, It is skid-mounted and designed as an oil- silencers, valves and instrumentation. free, dry-running compressor, driven by an electric motor. 2 Valve skid container Including process piping, switching and 7 Utility container (optional) control valves, O₂ analyser and field Including the instrument air station and instrumentation. the closed-loop cooling water system. 3 Adsorption vessels 8 Buffer vessel The system consists of two vertical-type The buffer vessel downstream of the adsorber vessels where the adsorption adsorbers ensures a continuous supply process takes place. The vessels are of oxygen. Read more: designed for outdoor installation. linde-engineering.com/adsorption 06 Oxygen generation Linde’s VPSA and PSA solutions. A large portfolio to suit individual needs. To ensure the perfect fit for
Load more

Recommended publications
  • Turbine Expanderexpander
    CryogenicsCryogenics –– whywhy?? MaciejMaciej ChorowskiChorowski WroclawWroclaw UniversityUniversity ofof TechnologyTechnology FacultyFaculty ofof MechanicalMechanical andand PowerPower EngineeringEngineering European Cryogenic Course Wroclaw 20 - 25 April, 2009 T, K 10 10 The word cryogenics was introduced by Core of the hottest stars 9 Kamerlingh Onnes and is formed from the 10 8 Greek: 10 Fusion reaction of hydrogen 7 10 Core of the Sun 6 – cold 10 5 10 – generated from TEMPERATUREVERY HIGH Plasma 4 10 Surface of the Sun 3 According to the convention adopted at the 10 Steam turbine Biological processes XIIII Congress of the International Institute of 2 10 High temperature superconductivity Boiling temperature of nitrogen Refrigeration, cryogenics treats concepts and Low temperature superconductivity 10 technologies connected to reaching and Boiling temperature of helium Superfluid helium 4 applying temperature below 120 K. 1 -1 In cryogenic temperatures: 10 -2 10 -3 - new physical phenomena are visible (liquefaction 10 Superfluid helium 3 -4 of gases, superfluidity, superconductivity); 10 -5 - all the reactions are slowed down; 10 The lowest measured temperature in the whole volume of a probe -6 - dis-order in the matter is vanishing, noises are 10 VERY LOW TEMPERATUREVERY LOW -7 avoided (cryo-electronics). 10 The lowest temperaure of copper nuclei -8 European Cryogenic Course 10 CERN Geneva 2010 -9 10 Bose-Einstein condensate HistoricalHistorical developmentdevelopment ofof cryogenicscryogenics andand relatedrelated technologiestechnologies
    [Show full text]
  • Merger Agreement Between Linde Intermediate Holding
    Notarial deed by Notary Dr. Tilman Götte, Munich, as of November 1, 2018 - UR 2924 G/2018 Convenience Translation MERGER AGREEMENT BETWEEN LINDE INTERMEDIATE HOLDING AG AND LINDE AKTIENGESELLSCHAFT Merger Agreement between Linde Intermediate Holding AG, Klosterhofstraße 1, 80331 Munich, – hereinafter also referred to as “Linde Intermediate” or the “Acquiring Company” – and Linde Aktiengesellschaft, Klosterhofstraße 1, 80331 Munich, - hereinafter also referred to as “Linde AG” or the “Transferring Company” – Acquiring Company and Transferring Company also referred to as “Parties” or individually referred to as a “Party” – - 2 - Preliminary Remarks I. Linde Intermediate is a stock corporation, incorporated under the laws of Germany and registered with the commercial register of the local court of Munich under HRB 234880, having its registered office in Munich, whose shares are neither admitted to trading on the regulated market segments of a stock exchange nor traded on an over-the-counter market of a stock exchange. The nominal capital of Linde Intermediate registered with the commercial register amounts to € 50,000. It is divided into 50,000 registered shares with no par value each having a notional value of € 1.00. The fiscal year of Linde Intermediate is the calendar year. The sole shareholder of Linde Intermediate is Linde Holding GmbH, registered with the commercial register of the local court of Munich under HRB 234787, having its registered office in Munich (“Linde Holding GmbH”). The nominal capital of Linde Holding GmbH is, in turn, fully held by Linde plc, a public limited company incorporated under the laws of Ireland, having its registered office in Dublin, Ireland, and its principal executive offices in Surrey, United Kingdom (“Linde plc”).
    [Show full text]
  • Rudolf Diesel — Man of Motion and Mystery Jack Mcguinn, Senior Editor
    addendum Rudolf Diesel — Man of Motion and Mystery Jack McGuinn, Senior Editor You have to admit, having an In 1893, he published his treatise, “Theory engine named after you is a and Construction of a Rational Heat singularly impressive achieve- Engine to Replace the Steam Engine and ment. After all, the combustion the Combustion Engines Known Today.” It engine isn’t named for anyone. No one was the foundation of his research that led refers to the steam engine as “the Watt” to the Diesel engine. But later that year, it engine. was back to the drawing board; Diesel came But then along came Rudolf Diesel to realize that he wasn’t there yet, and later (1858–1913), and with him — the that year filed another patent, correcting his Diesel engine, the engine that liter- mistake. ally took the steam out of a wide range Central to Diesel’s game-changing engine of engine applications. Born in Paris creation was his understanding of thermo- to Bavarian immigrants in some- dynamics and fuel efficiency, and that “as what humble circumstances — his much as 90%” of fuel energy “is wasted in father Theodor was a bookbinder and a steam engine.” Indeed, a signature accom- leather goods manufacturer — Rudolf plishment of Diesel’s engine is its elevated was shortly after birth sent to live for efficiency ratios. After several years of fur- nine months with a family of farmers ther development with Heinrich von Buz in Vincennes, for reasons that remain of Augsburg’s MAN SE, by 1897 the Diesel sketchy. Upon return to his parents, Rudolf was excelling in engine was a reality.
    [Show full text]
  • Air Separation Plants. History and Technological Progress in the Course of Time
    Air separation plants. History and technological progress in the course of time. History and technological progress of air separation 03 When and how did air separation start? In May 1895, Carl von Linde performed an experiment in his laboratory in Munich that led to his invention of the first continuous process for the liquefaction of air based on the Joule-Thomson refrigeration effect and the principle of countercurrent heat exchange. This marked the breakthrough for cryogenic air separation. For his experiment, air was compressed Linde based his experiment on findings from 20 bar [p₁] [t₄] to 60 bar [p₂] [t₅] in discovered by J. P. Joule and W. Thomson the compressor and cooled in the water (1852). They found that compressed air cooler to ambient temperature [t₁]. The pre- expanded in a valve cooled down by approx. cooled air was fed into the countercurrent 0.25°C with each bar of pressure drop. This Carl von Linde in 1925. heat exchanger, further cooled down [t₂] proved that real gases do not follow the and expanded in the expansion valve Boyle-Mariotte principle, according to which (Joule-Thomson valve) [p₁] to liquefaction no temperature decrease is to be expected temperature [t₃]. The gaseous content of the from expansion. An explanation for this effect air was then warmed up again [t₄] in the heat was given by J. K. van der Waals (1873), who exchanger and fed into the suction side of discovered that the molecules in compressed the compressor [p₁]. The hourly yield from gases are no longer freely movable and this experiment was approx.
    [Show full text]
  • Paving the Way for LNG
    Plants, terminals and equipment for the entire LNG value chain Paving the way for LNG Making our world more productive 2 LNG value chain Introduction Driven by increasing natural gas demand and decreasing costs along the whole LNG value chain (due to significant economies of scale, improvements in technologies, etc.), investments in LNG infrastructure are growing rapidly in the last years. LNG has turned from being an expensive and regionally traded fuel to a globally traded source of energy with rapidly diminishing costs. In China, Norway and lately in particular in the US, petroleum fuels With more than 125 years of comprehensive experience in the Linde offers innovative and economical solutions for the entire LNG have been successfully substituted by LNG in various applications, handling of cryogenic liquids, Linde Engineering has a track record in value chain and has more than 40 years experience in designing, mainly for heavy trucking, remote-power generation and marine the design and performance of a wide range of natural gas projects building and operating LNG plants and proprietary cryogenic fueling. Today the volumes are still relatively small, however studies including upstream natural gas liquids recovery (NGL plants), feed equipment. indicate substantial demand for additional domestic LNG capacities in gas pre-treatment and liquefaction, transport and distribution of LNG many countries. These include the entire Baltic Area (ECA) and South regasification in both LNG import and export terminals. East Asia. As a consequence, an appropriate infrastructure consisting of small- to mid-scale LNG liquefaction plants, import terminals and Linde Engineering is well recognised as a reliable technology refuelling stations will be built up and/or expanded.
    [Show full text]
  • Mergers & Acquisitions in the US Industrial Gas Business
    Mergers & Acquisitions in the US Industrial Gas Business PART II – THE MAJOR INDUSTRY SHAPERS By Peter V. Anania, Leaders LLC he Industrial Gas (IG) industry has seen tremendous growth a process to separate oxygen in 1880. In 1886 the brothers Brin started over the past 100 years, fueled by rapidly expanding technol- commercially developing the use of oxygen. T ogy in market leading countries that required more mixes of Interestingly, one of BOC’s first mergers — and now its last — was gases (including the exotics), purer gases for high-tech applications, with Linde. In 1906, Linde joined with Brin Oxygen by contributing as well as new applications of traditional gases. With the develop- its British Linde patents. These patents represented a new method for ment of industry in emerging economies, demand for industrial producing oxygen by cryogenic distillation of air. The resulting gases continues to grow worldwide. This is Part II of this series that merged entity was renamed British Oxygen Company or BOC. In the examines mergers and acquisitions activity in the industrial gas busi- 1920s, a process for the large-scale production of liquid oxygen ness. In this feature we look at some of the “majors” and how they allowed the oxygen to be delivered in liquid form by road tanker and have grown over the years through acquisitions. In compiling this greatly expanded its market applications. article, we researched the websites of many of the companies men- BOC’s growth in the first half of the 20th century was achieved tioned herein, had access to the archives of JR Campbell Associates, largely by developing or acquiring rights to new technology and Inc., along with discussions with Buzz Camp- processes, including further improvements in liq- bell, and used The History of Industrial Gases, uefaction and cryogenic cooling in the 1930s.
    [Show full text]
  • 1 Introduction
    1 1 Introduction The history of industrial gases is inextricably linked to the rapid pace of industri- alisation that marked the nineteenth century. The large-scale generation of certain gases opened the door for new types of technologies and production processes. Acetylene, for example, was discovered by E. Davy in 1836. A signifi cant landmark followed in 1862, when F. Wöhler succeeded in producing acetylene from the reaction between calcium carbide and water. Then, in 1892, T. L. Wilson and H. Moissan discovered a process for generating calcium carbide in an electric furnace. This paved the way for industrial-scale production of acetylene in 1895 (see also Section 8.2). Initially, acetylene was mainly used for lighting purposes due to its bright fl ame. Later, its high combustion temperature in oxygen prompted development of autogenous cutting and welding technology, starting in 1901. An even more important step from today’s perspective was the liquefaction of air by Carl von Linde, marking the birth of an entirely new industry. C. v. Linde employed the Joule–Thomson effect, decreasing the temperature of the gas by adiabatic expansion. In 1895, he achieved continuous generation of liquid air at a yield of three litres per hour using a laboratory plant [1.1]. The following years saw the construction and delivery of the fi rst small commercial air liquefaction plants. Figure 1.1 shows a typical early air liquefi er (ca. 1899). Fig. 1.1 Typical assembly of a Linde air liquefi er (ca. 1899). Industrial Gases Processing. Edited by Heinz-Wolfgang Häring Copyright © 2008 WILEY-VCH Verlag GmbH & Co.
    [Show full text]
  • How Liquid Helium and Superconductivity Came to Us
    IEEE/CSC & ESAS EUROPEAN SUPERCONDUCTIVITY NEWS FORUM (ESNF), No. 16, April 2011 Heike Kamerlingh Onnes and the Road to Liquid Helium Dirk van Delft, Museum Boerhaave – Leiden University e-mail: [email protected] Abstract – I sketch here the scientific biography of Heike Kamerlingh Onnes, who in 1908 was the first to liquefy helium and in 1911 discovered superconductivity. A son of a factory owner, he grew familiar with industrial approaches, which he adopted and implemented in his scientific career. This, together with a great talent for physics, solid education in the modern sense (unifying experiment and theory) proved indispensable for his ultimate successes. Received April 11, 2011; accepted in final form April 19, 2011. Reference No. RN19, Category 11. Keywords – Heike Kamerligh Onnes, helium, liquefaction, scientific biography I. INTRODUCTION This paper is based on my talk about Heike Kamerlingh Onnes (HKO) and his cryogenic laboratory, which I gave in Leiden at the Symposium “Hundred Years of Superconductivity”, held on April 8th, 2011, the centennial anniversary of the discovery. Figure 1 is a painting of HKO from 1905, by his brother Menso, while Figure 2 shows his historically first helium liquefier, now on display in Museum Boerhaave of Leiden University. Fig. 1. Heike Kamerling Onnes (HKO), 1905 painting by his brother Menso. 1 IEEE/CSC & ESAS EUROPEAN SUPERCONDUCTIVITY NEWS FORUM (ESNF), No. 16, April 2011 Fig. 2. HKO’s historical helium liquefier (last stage), now in Museum Boerhaave, Leiden. I will address HKO’s formative years, his scientific mission, the buiding up of a cryogenic laboratory as a direct consequence of this mission, add some words about the famous Leiden school of instrument makers, the role of the Leiden physics laboratory as an international centre of low temperature research, to end with a conclusion.
    [Show full text]
  • Thermodynamic Performance Analysis of Gas Liquefaction Cycles for Cryogenic Applications
    Journal of Thermal Engineering, Vol. 5, No. 1, pp. 62-75, January, 2019 Yildiz Technical University Press, Istanbul, Turkey THERMODYNAMIC PERFORMANCE ANALYSIS OF GAS LIQUEFACTION CYCLES FOR CRYOGENIC APPLICATIONS C. Yilmaz1,*, T. H. Cetin2, B. Ozturkmen2, M. Kanoglu2 ABSTRACT In this paper presents an analysis of the thermodynamic cycles the most commonly used for the liquefaction of gases in order to evaluate and compare their performance under given working conditions and system component efficiencies. The cycles considered are simple Linde-Hampson cycle, precooled Linde- Hampson cycle, Claude cycle, and Kapitza cycle. First and second law relations are investigated for each cycle and performance parameters are evaluated. Thermodynamically performances criteria are compared of cycles with respect to the each other. Cycles are model in the computer environment and analyzed with Engineering Equation Solver (EES) software program. Cycles of the liquefaction fractions, coefficient of performances and second law of efficiencies are calculated for the liquefaction of different gases. Second law efficiencies are calculated as 13.4%, 21.8%, 62.9%, and 77.2% for simple Linde-Hampson cycle, pre-cooled Linde-Hampson cycle, Claude cycle, and Kapitza cycle, respectively. Claude and Kapitza cycles give better performance but simple and precooled Linde-Hampson cycle has the advantages of the simplicity of their setup. Keywords: Cryogenic Cycles, Linde-Hampson, Claude, Kapitza, J-T Expansion, Thermodynamic Analysis INTRODUCTION Liquefaction is a key branch of cryogenics and has wide application areas including producing commercial liquid gases and cryogenic engineering applications. The main scope of cryogenic engineering is the design, development and improvement of low temperature systems and components.
    [Show full text]
  • 125 Years of Linde 125 Years of Linde of 125 Years a Chronicle
    chronik_Cover_gb 05.07.2004 17:54 Uhr Seite 1 Idea no 0001– no 6385 125 Years of Linde 125 Years of Linde of 125 Years A Chronicle Idea No 0001 – No 6385 “The only thing I find comparable to the great satisfaction of a scientific endeavor pursued together with ambitious and productive men is production carried out on one’s own and in one’s own area of expertise.” Carl von Linde in a letter to Göttingen mathematician Felix Klein, 1895 Inventive spirit and innovation are still our mainsprings A look back at the achievements of engineer/inventor Carl von Today, Linde is the world’s largest supplier of industrial and Linde and at the development of the company he helped found, medical gases. We stand for cutting-edge technology in inter- the “Gesellschaft für Linde’s Eismaschinen,“ into today’s Linde AG national facilities engineering, hold a leading position among means more to us than fond memories – it is also a commitment the most important manufacturers of forklift trucks and warehouse to the future. equipment and are the market leaders in refrigeration technology The abilities and characteristics exemplified by scientist and in Europe. With some 46,500 employees, we achieved sales of inventor Carl von Linde during his lifetime are, today more than approximately 9 billion euro in fiscal year 2003. ever, a model for corporate leaders who want to lead a technol- This impressive corporate development did not happen on its ogy group like Linde into a long-term, successful future. His own, and it is certainly no guarantee of future success.
    [Show full text]
  • Keeping You Cool. Delivering Your Refrigerant Gas and Service Needs
    Keeping you cool. Delivering your refrigerant gas and service needs. 02 Delivering your refrigerant gas and service needs Delivering your refrigerant gas and service needs 03 Why choose Linde Gas? A global leader and trusted partner. Linde Gas is a global leader in refrigerant solutions and services. Our products span both traditional fluorocarbon and natural refrigerants making us a trusted partner to a vast range of industries around the world. They are vital for refrigeration, process chilling and heat extraction applications used in the food and beverage, pharmaceuticals, industrial manufacturing, chemical and petrochemical industries. They also provide air conditioning in our transport, shops, offices and public buildings and homes. Whatever your application, wherever you are, Linde Gas can meet all your needs relating to the delivery, handling and management of refrigerant gases. Proven industry expert. Meeting your refrigerant gas and service needs. Linde Gas solutions and services span: Wide product range Total solution and services • Refrigerant gases including fluorocarbon and environmentally friendly, • Specialist services such as refrigerant recovery and reclamation, on site natural gases such as refrigerant-grade carbon dioxide (R744), ammonia audits and risk assessment (R717), hydrocarbons and hydrocarbon blends • Safe and legal waste management • A wide choice of packaging – cylinders, drums, ISO tanks and bulk road • Technical and operational expertise – advice on the best gas for your tankers needs, local legislation/regulatory • Pressure testing and leak detection gases compliance and environmentally friendly alternatives • Cutting and welding gases • Training tailored to end user needs Global branch network • Best in class logistics ensuring optimal product quality and security of supply • Local customer service 04 Delivering your refrigerant gas and service needs Delivering your refrigerant gas and service needs 05 Serving you wherever you are.
    [Show full text]
  • CO2-Refrigeration in a Historic Perspective CO2 Is Back!
    CO2 is back! CO2-refrigeration in a historic perspective (2000) Prof. Dr.-Ing. Armin Hafner Professor Refrigeration Technology NTNU, EPT 7491 Trondheim Norway GIAN @ Indian Institute of Technology Madras; October 2017 GIAN @ Indian Institute of Technology Madras; October 2017 Professor Gustav Lorentzen 1915-1995 First draft made for a patent application on how to operate and control transcritical CO2- vapour compression systems November 1988 CO2-refrigeration technology prior 1988? GIAN @ Indian Institute of Technology Madras; October 2017 3 GIAN @ Indian Institute of Technology Madras; October 2017 4 Inventors and pioneers of mechanical refrigeration Content Vapour compression cycle: – Oliver Evans (1755-1819), USA • How developed refrigeration technology? ”The Abortion of the Young Steam Engineer’s Guide”, 1805 • Factors which contributed to the development – Jacob Perkins (1766-1849), American living in London British Patent No 6662, 14. August 1834 •CO2 i relation to other working fluids Machine applying sulphur-ether, build by John Hague • The people behind the innovations • Synergies to todays situation • CO2 processes / system configurations and modifications • Reasons why CO2 refrigeration technology was absent between 1960 to 1990 MOTIVATION: Can we learn something when studying the historic CO2 refrigeration systems? GIAN @ Indian Institute of Technology Madras; October 2017 5 GIAN @ Indian Institute of Technology Madras; October 2017 6 Inventors and pioneers of mechanical refrigeration Inventors and pioneers of mechanical refrigeration
    [Show full text]