DOCSLIB.ORG

Log Hauling | BC Forest Safety Council Page 1 of 1

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Log Hauling | BC Forest Safety Council Page 1 of 1 Log Hauling | BC Forest Safety Council Page 1 of 1 Log Hauling Safety Alert Type: Log Hauling Location: 500 Road-east of Quesnel Date of Incident: 2007-12-27 Company Name: Inwood Trucking Details of Incident: A loaded tridem long log truck was loaded on the 500 Road. The road was in winter condition-frozen and icy. While coming around a corner on a 10-12% downhill slope, the logging truck met a pick up (empty direction) towing a trailer with 2 snowmobiles on it. The pick up did not have a radio. The log truck tried to slow and allow the pick up to pass, however, the pick up driver panicked and began to back up. The trailer behind the pick up jackknifed in front of the logging truck, blocking the road. At this point, the log truck driver applied his brakes, causing his trailer to jackknife as well. The right front corner of the loaded logging truck bumped the snowmobile trailer, pushing the pick up around. At this point the loaded truck came to a stop. During the investigation, it became known that the pick up was on the wrong road. The young driver had become lost while looking for a popular snowmobile area and turned onto an active logging road. He ignored the signs warning of radio use and industrial traffic. There was minimal damage to both vehicles and no injuries. However, the potential for serious injury was enormous. Only the defensive driving of the log truck driver prevented a more serious outcome. Recommended Preventative Actions: 1. Public should be more aware of industrial traffic and radio control on multi user roads. 2. Pick ups should be radio equipped, keep to their own side of the road and use pullouts to clear industrial traffic. 3. All log truck drivers should drive defensively and be aware of non industrial, recreational traffic at all times. More Information Contact Details: Lloyd Inwood (250) 992-6097 Copyright © 2008 BC Forest Safety Council. All rights reserved. http://www.bcforestsafe.org/node/164 3/24/2009 Manual harvesting/bucking | BC Forest Safety Council Page 1 of 1 Manual harvesting/bucking Safety Alert Type: Manual Harvesting/Bucking Date of Incident: 2007-12-27 Company Name: Long Shot Holdings Ltd. Details of Incident: Due to road builders falling the right of way into the standing timber, an entangled mess of trees was left standing at the north end of the block. A faller was sent in to clear out the mess. The faller attempted to straighten the mess and in doing so a tree slid down another; which had been left fallen down through the standing timber. This caused the ground that the faller was working around to become unstable. Recommended Preventative Actions: A loader could not knock the trees down because of the steepness of the right of way. It was decided to drag the trees over with the lines of the grapple yarder. It was noted that this was a high hazard incident and the outcome could have been worse than it was. All employees were reminded that everyone has the right to refuse unsafe work. INVESTIGATION: It was shown that the road builders had fallen the right of way trees into the standing timber. This made it hard for a loader to knock them down as the slope was to steep on the right of way. The faller attempted to fall the trees and after the way the first tree came down the faller refused to attempt the others. The faller did the right thing. More Information Contact Details: Laura Olynyk Long Shot Holdings Copyright © 2008 BC Forest Safety Council. All rights reserved. http://www.bcforestsafe.org/node/184 3/24/2009 FOREST INDUSTRY SAFETY ALERT Close Call/Serious Incident Location: Cowichan (L-Line) Date of Incident: November 23, 2007 Details of Incident: A faller was bucking the root off a blown down fir tree when the root wad, which was partially attached, rolled from its original resting place down the slope increasing the load energy on the tree. When the cut was completed the top portion of the tree kicked back striking the fallers left lower leg pinning him and fracturing his leg. Faller misjudged the hazard of the loaded stem and the potential for the energy to increase with the root wad moving down hill. Recommended Preventative Actions: 1. Eliminate loaded hazards by bucking at pivot points. 2. Faller positioning, ensure safe position prior to making any cuts. 3. Where pivot points or hazards can't be removed do not attempt any bucking 4. Ensure this incident is reviewed with all fallers and documented For more information, please call: Ted LeRoy Trucking Ltd. Safety and Compliance Dept. Jim Vaux or Shawn Munson (250) 246-2880 1 2 Log Hauling | BC Forest Safety Council Page 1 of 1 Log Hauling Safety Alert Type: Log Hauling Location: 1320.5 km-east of Quesnel Date of Incident: 2007-12-23 Company Name: Inwood Trucking Details of Incident: A short log truck was returning to the bush on the 1300 Road. Winter road conditions were present. After calling “1318 empty” the driver cleared a loaded truck and started to the bush again. After calling “1320 empty” the driver was proceeding around a right hand corner at 1320.5 when he met a loaded truck. The driver of the empty truck swerved to the right in an attempt to allow the load to pass. However, he could not completely leave the road due to the heavy snow bank. The driver of the loaded truck also swerved to try and clear the empty truck, hitting the ditch in the process. Despite the road being wide enough, the trucks could not clear each other and the driver’s sides of the trucks hit. The empty truck sustained damage to the driver’s side cab and the trailer. The loaded truck sustained severe damage from the impact and from hitting the ditch in an effort to avoid the crash. Fortunately, there were no injuries as a result of the incident. Recommended Preventative Actions: 1. Warn all drivers to use radios and clear loaded traffic. 2. Keep to proper side of road 3. Keep speed down during periods of winter road conditions. 4. Drive defensively and expect the unexpected. More Information Contact Details: (250) 992-6097 Copyright © 2008 BC Forest Safety Council. All rights reserved. http://www.bcforestsafe.org/node/163 3/24/2009 HAZARD ALERT | BC Forest Safety Council Page 1 of 1 HAZARD ALERT Safety Alert Type: Log Hauling Date of Incident: 2007-12-17 Company Name: Buckley House Holdings Ltd. Details of Incident: A lowbed driver had attached a belt to the pin holding the trailer hitch onto the truck. This was apparently done so he did not have to reach in when pulling the pin to disconnect. The belt was fairly long and hung out from the hitch. The lowbed was moving a D6 Cat and due to slippery road conditions the driver put his chains on. As the truck was proceeding down the road one of the chains caught the belt and pulled the pin out of the hitch. This caused the trailer to detached from the truck. The trailer started sliding backwards down a hill pulling the truck with it. Fortunately the driver was able to stop the truck with minimal damage, he then hooked up and proceeded. This could have been a very serious incident. This alert is to advise all drivers to inspect their trucks regularly and identify potential hazards. Also it is recommending not to add anything on to equipment. Let all continue to work and drive safe. Copyright © 2008 BC Forest Safety Council. All rights reserved. http://www.bcforestsafe.org/node/321 3/24/2009 Mechanical Harvesting | BC Forest Safety Council Page 1 of 1 Mechanical Harvesting Safety Alert Type: Mechanical Harvesting Location: Malakwa Date of Incident: 2007-12-17 Details of Incident: Loader Operator was working on setting up roadside yarded logs for loading at approximately 5:30 am before yarding crew arrived. As loader was moving logs around a hemlock log slid down the hill in the dark and hit the backspar machine approx. 400 ft. below road. Loaderman was not aware that a log had slid down and hit the backspar machine until the yarding crew arrived and noticed the cab on the backspar machine was missing. No injuries resulted from this incident. Recommended Preventative Actions: Keep separation between loading area and active yarding roads; make sure logs are stable on road or landing. Yarding crew to be safe distance from the active yarding road during any operations, and do not sit in backspar machine during active yarding. Copyright © 2008 BC Forest Safety Council. All rights reserved. http://www.bcforestsafe.org/node/196 3/24/2009 Manual harvesting/bucking | BC Forest Safety Council Page 1 of 1 Manual harvesting/bucking Safety Alert Type: Manual Harvesting/Bucking Location: Clearwater Date of Incident: 2007-12-14 Details of Incident: Hand faller fell small Pine tree which landed on some debris on ground kicking up small piece of slash that came back and hit him in the knee causing a loud snapping noise. He had previously bucked some slash in the path of the tree prior to falling it. The faller continued to work as no pain was experienced but began to notice incomplete functioning of his knee. He still finished his day (he only had a few trees left) then went to hospital. Doctor diagnosed him with a 3rd degree tear of NCL tendon on his right knee.
Load more

Recommended publications
  • Logging Songs of the Pacific Northwest: a Study of Three Contemporary Artists Leslie A
    Florida State University Libraries Electronic Theses, Treatises and Dissertations The Graduate School 2007 Logging Songs of the Pacific Northwest: A Study of Three Contemporary Artists Leslie A. Johnson Follow this and additional works at the FSU Digital Library. For more information, please contact [email protected] THE FLORIDA STATE UNIVERSITY COLLEGE OF MUSIC LOGGING SONGS OF THE PACIFIC NORTHWEST: A STUDY OF THREE CONTEMPORARY ARTISTS By LESLIE A. JOHNSON A Thesis submitted to the College of Music in partial fulfillment of the requirements for the degree of Master of Music Degree Awarded: Spring Semester, 2007 The members of the Committee approve the Thesis of Leslie A. Johnson defended on March 28, 2007. _____________________________ Charles E. Brewer Professor Directing Thesis _____________________________ Denise Von Glahn Committee Member ` _____________________________ Karyl Louwenaar-Lueck Committee Member The Office of Graduate Studies has verified and approved the above named committee members. ii ACKNOWLEDGEMENTS I would like to thank those who have helped me with this manuscript and my academic career: my parents, grandparents, other family members and friends for their support; a handful of really good teachers from every educational and professional venture thus far, including my committee members at The Florida State University; a variety of resources for the project, including Dr. Jens Lund from Olympia, Washington; and the subjects themselves and their associates. iii TABLE OF CONTENTS ABSTRACT .................................................................................................................
    [Show full text]
  • Forestry Materials Forest Types and Treatments
    -- - Forestry Materials Forest Types and Treatments mericans are looking to their forests today for more benefits than r ·~~.'~;:_~B~:;. A ever before-recreation, watershed protection, wildlife, timber, "'--;':r: .";'C: wilderness. Foresters are often able to enhance production of these bene- fits. This book features forestry techniques that are helping to achieve .,;~~.~...t& the American dream for the forest. , ~- ,.- The story is for landolVners, which means it is for everyone. Millions . .~: of Americans own individual tracts of woodland, many have shares in companies that manage forests, and all OWII the public lands managed by government agencies. The forestry profession exists to help all these landowners obtain the benefits they want from forests; but forests have limits. Like all living things, trees are restricted in what they can do and where they can exist. A tree that needs well-drained soil cannot thrive in a marsh. If seeds re- quire bare soil for germination, no amount of urging will get a seedling established on a pile of leaves. The fOllOwing pages describe th.: ways in which stands of trees can be grown under commonly Occllrring forest conditions ill the United States. Originating, growing, and tending stands of trees is called silvicllllllr~ \ I, 'R"7'" -, l'l;l.f\ .. (silva is the Latin word for forest). Without exaggeration, silviculture is the heartbeat of forestry. It is essential when humans wish to manage the forests-to accelerate the production or wildlife, timber, forage, or to in- / crease recreation and watershed values. Of course, some benerits- t • wilderness, a prime example-require that trees be left alone to pursue their' OWII destiny.
    [Show full text]
  • Response of Nesting Northern Goshawks to Logging Truck Noise Kaibab National Forest, Arizona
    RESPONSE OF NESTING NORTHERN GOSHAWKS TO LOGGING TRUCK NOISE KAIBAB NATIONAL FOREST, ARIZONA Teryl G. Grubb U.S. Forest Service Rocky Mountain Research Station Flagstaff, Arizona Angela E. Gatto 8 May 2012 U.S. Forest Service North Kaibab Ranger District Kaibab National Forest Fredonia, Arizona Larry L. Pater Noise Consultant Champaign, Illinois David K. Delaney U.S. Army Research and Development Center Construction Engineering Research Laboratory Champaign, Illinois RESPONSE OF NESTING NORTHERN GOSHAWKS TO LOGGING TRUCK NOISE KAIBAB NATIONAL FOREST, ARIZONA Teryl G. Grubb U.S. Forest Service Rocky Mountain Research Station Flagstaff, Arizona Angela E. Gatto U.S. Forest Service North Kaibab Ranger District Kaibab National Forest Fredonia, Arizona Larry L. Pater Noise Consultant Champaign, Illinois David K. Delaney U.S. Army Engineer Research and Development Center Construction Engineering Research Laboratory Champaign, Illinois Final Report to Southwest Region (R-3) U.S. Forest Service 8 May 2012 EXECUTIVE SUMMARY At present log hauling is categorically precluded from northern goshawk (Accipter gentilis) post- fledging family areas (PFAs) on the Kaibab Plateau to the detriment of efficient U. S. Forest Service contract logging. The goal of the current research was to test sufficiently with a logging truck hauling near actively nesting goshawks to establish critical thresholds for distance and noise levels, as well as assess current levels of frequency/duration/timing, i.e., concentration of exposure. Collaboration with U.S. Forest Service Rocky Mountain Research Station (RMRS) and U.S. Army Engineer Research and Development Center/Construction Engineering Research Laboratory (ERDC/CERL) brought wildlife and acoustical expertise, as well as sophisticated, professional grade, recording equipment to the project.
    [Show full text]
  • Design Vehicle Configuration Analysis and CSA-S6-00 Implication Evaluation Phase II
    BUCKLAND & TAYLOR LTD. Bridge Engineering MINISTRY OF FORESTS Design Vehicle Configuration Analysis and CSA-S6-00 Implication Evaluation Phase II 2003 November 19 Our Ref: 1579 Prepared by: Darrel P. Gagnon, P.Eng. Reviewed by: Peter G. Buckland, P.Eng. BUCKLAND & TAYLOR LTD. 101-788 Harbourside Drive North Vancouver, BC, Canada V7P 3R7 Tel: (604) 986-1222 Fax: (604) 986-1302 E-mail: [email protected] Website: www.b-t.com W:\1579\Phase II Final Report\Title.fm BUCKLAND & TAYLOR LTD. Bridge Engineering Executive Summary The Ministry of Forests (BCMoF) had previously commissioned Buckland & Taylor Ltd. to conduct of review of the Forest Service Bridge Design and Construction Manual and CAN/ CSA-S6-00 (CHBDC) to determine if the existing BCMoF Design Vehicle configurations are reasonably representative of the logging vehicles now being used in the BC forest industry and if these configurations are appropriate for use with the load factors in CHBDC. A survey of logging truck weights conducted by Forest Engineering Research Institute of Canada (FERIC) provided the base data for this analysis and the results of this study were presented to the BCMoF in a report entitled ’MoF Design Vehicle Configuration Analysis and CSA-S6-00 Implication Evaluation’ dated 2003 January 04 (draft report dated 2002 May 13). Although the report made some recommendations for revisions to the L75 Design Vehicle and corresponding load factors, it was concluded that insufficient data was available to accurately assess the L100, L150 and L165 Design Vehicles or trucks conducting movements of logging equipment. Although truck loadings and bridge design capacity requirements could vary significantly between operationing regions and individual operators, comments received from personnel involved in the industry indicated that most companies were having forestry bridges designed for load levels that exceeded the maximum measured weights of most of the logging trucks.
    [Show full text]
  • WAC 296-54 WAC, Logging Operations
    Chapter 296-54 WAC Introduction Safety Standards for Logging Operations _________________________________________________________________________________________________________ Chapter 296-54 WAC Safety Standards for Logging Operations (Form Number F414-016-000) This book contains rules for safety standards for logging operations, as adopted under the Washington Industrial Safety and Health Act of 1973 (Chapter 49.17 RCW). The rules in this book are effective October 2017. A brief promulgation history, set within brackets at the end of this chapter, gives statutory authority, administrative order of promulgation, and date of adoption of filing. TO RECEIVE E-MAIL UPDATES: Sign up at https://public.govdelivery.com/accounts/WADLI/subscriber/new?topic_id=WADLI_19 TO PRINT YOUR OWN PAPER COPY OR TO VIEW THE RULE ONLINE: Go to https://www.lni.wa.gov/safety-health/safety-rules/rules-by-chapter/?chapter=54/ DOSH CONTACT INFORMATION: Physical address: 7273 Linderson Way Tumwater, WA 98501-5414 (Located off I-5 Exit 101 south of Tumwater.) Mailing address: DOSH Standards and Information PO Box 44810 Olympia, WA 98504-4810 Telephone: 1-800-423-7233 For all L&I Contact information, visit https://www.lni.wa.gov/agency/contact/ Also available on the L&I Safety & Health website: DOSH Core Rules Other General Workplace Safety & Health Rules Industry and Task-Specific Rules Proposed Rules and Hearings Newly Adopted Rules and New Rule Information DOSH Directives (DD’s) See http://www.lni.wa.gov/Safety-Health/ Chapter 296-54 WAC Table of Contents Safety Standards for Logging Operations _________________________________________________________________________________________________________ Chapter 296-54 WAC SAFETY STANDARDS FOR LOGGING OPERATIONS WAC Page 296-54-503 Variance. .................................................................. 1 WAC 296-54-505 Definitions.
    [Show full text]
  • Northeastern Loggers Handrook
    ./ NORTHEASTERN LOGGERS HANDROOK U. S. Deportment of Agricnitnre Hondbook No. 6 r L ii- ^ y ,^--i==â crk ■^ --> v-'/C'^ ¿'x'&So, Âfy % zr. j*' i-.nif.*- -^«L- V^ UNITED STATES DEPARTMENT OF AGRICULTURE AGRICULTURE HANDBOOK NO. 6 JANUARY 1951 NORTHEASTERN LOGGERS' HANDBOOK by FRED C. SIMMONS, logging specialist NORTHEASTERN FOREST EXPERIMENT STATION FOREST SERVICE UNITED STATES GOVERNMENT PRINTING OFFICE - - - WASHINGTON, D. C, 1951 For sale by the Superintendent of Documents, Washington, D. C. Price 75 cents Preface THOSE who want to be successful in any line of work or business must learn the tricks of the trade one way or another. For most occupations there is a wealth of published information that explains how the job can best be done without taking too many knocks in the hard school of experience. For logging, however, there has been no ade- quate source of information that could be understood and used by the man who actually does the work in the woods. This NORTHEASTERN LOGGERS' HANDBOOK brings to- gether what the young or inexperienced woodsman needs to know about the care and use of logging tools and about the best of the old and new devices and techniques for logging under the conditions existing in the northeastern part of the United States. Emphasis has been given to the matter of workers' safety because the accident rate in logging is much higher than it should be. Sections of the handbook have previously been circulated in a pre- liminary edition. Scores of suggestions have been made to the author by logging operators, equipment manufacturers, and professional forest- ers.
    [Show full text]
  • Logging Truck Driver
    [Company Logo] Company Name Safe Work Procedure – Logging Truck Driver PERSONAL PROTECTIVE EQUIPMENT: Adequate Footwear with good traction soles Hi-vis Hardhat Gloves Hi-vis Vest Hearing Protection PROCEDURES: Vehicle Inspections • Inspect the logging truck to ensure it is in safe operating condition. • Check the logging rigging regularly to ensure the cables, bunks, stakes, lift straps, couplings, lights and other critical components are free of defects and in good working order. • Check the condition of the brakes and adjust them regularly to ensure they are functioning properly. • Ensure the required government inspections of the vehicle are conducted and are current. Operating the Vehicle • All logging trucks must be equipped with a two-way radio using the frequency posted for the particular haul road. • Drive with the headlights on at all times. • Passengers are not allowed unless they have proper authorization. • Operate the logging truck in a safe manner. Drive within the posted speed limits and/or within safe speeds determined by the conditions of the road. • Always get into and leave the truck in a safe manner using the handholds provided to prevent slipping and tripping. • Wear the personal protective equipment required when getting out of the vehicle. • Refer to Section “Rules of the Road” for Operating the vehicle on industrial forest roads and use of the two-way radio system. • Report any observed unsafe haul road conditions to your supervisor, the logging contractor or the sawmill personnel. Tire Chains • Where winter conditions prevail, always adequately chain up the vehicle in a safe flat location before you encounter areas where vehicle traction is questionable.
    [Show full text]
  • The Legacy of the Log Boom Humboldt County Logging from 1945 to 1955 Logging in Humboldt County in Northwestern California Began in 1850
    Paul G. Wilson The Legacy of the Log Boom Humboldt County Logging from 1945 to 1955 Logging in Humboldt County in northwestern California began in 1850. When settlers first saw the giant old growth coast redwoods in Humboldt County they were in awe of them. These trees had diameters up to 30 feet and heights up to almost 400 feet. Old growth redwood trees are the oldest living things on earth; they can live about two thousand years. The settlers of Humboldt County had a respect for the redwoods; however, the settlers saw an immediate profit to be made. Old growth redwood lumber was used to build houses, railroad ties, shingle bolts, fence posts, and grape stakes.1 Redwood timberland in Humboldt County was located near the coast and extended twenty-five miles inland. The mills that cut the redwood logs into dimension sized lumber were located on the shores of Humbolt Bay. Humboldt Bay was a safe place for ocean vessels to pick up loads of redwood lumber to be sent to San Francisco Bay. Lumber vessels were often overloaded with redwood lumber. Because the vessels were piled with lumber, the vessels were believed to be unsinkable.2 Redwood lumber was sent all over the world for its preference in woodworking. In 1878 the United States government passed the Timber and Stone Act which allowed loggers to buy 160 acres of timberland for $2.50 per acre as long as the loggers "improved" the land through logging and ranching. Loggers acquired thousands of acres of redwood land and often formed partnerships to begin lumber companies.
    [Show full text]
  • Securing Loads on Logging Trucks \ J.A
    SECURING LOADS ON LOGGING TRUCKS \ J.A. Stulen g N.Z. Logging 1,s:; Ram,reh Assn. Inc. PX). Box 147, Ratorua . (1J Wrapzround strops released 1.21 Load faIls to the ground INTRODUCTION Over the past twelve months, LIRA has been involved with the work of an industry committee which has been dealing with problems in securing log loads on trucks. This committee has recently submitted recommendations to the Department of Labour to assist them in their current revision of the "Safety Code for Bush Undertakings - Part 2 : Transportation". This report discusses and highlights the important aspects of the committee work. A full project report covering all tests and results will be released later this year. ACKNOWLEDGEMENT LIRA acknowledges the work of the committee and its members in making its results available for this publication. BACKGROUND In November, 1982, the DSIR completed a series of tests and a demonstration for the Institute of Road Transport Engineers (IRTE). These showed how dynamic forces in a logging truck frame and its load securing devices could be measured. The success of this early work encouraged the formation of an industry committee with representatives from the following organisations :- Ministry of Transport (MOT) Department of Labour (DOL) Department of Scientific and Industrial Research (DSIR) Institute of Road Transport Engineers (IRTE) Road Transport Association (RTA) Logging Industry Research Association (LIRA) and a number of logging companies. The principle objective of the committee was : "To establish safe and sensible working regulations for the securing of log loads on logging trucks". To achieve this end, more tests were undertaken usino the DSIR and the eauioment and assistance of a number of logging companies and t6eir staff.
    [Show full text]
  • Lt Master File
    1 VOLUME 49 NUMBER 1 VOLUME 49 NUMBER 1 To Advertise Call: (800) 462-8283 JaNUaRy 2013 r o , M e L a s 8 7 1 . o n t i M r e P 5 2 4 8 - 2 3 5 8 9 a W , c s i L a H e H D I A P . H J 6 0 2 4 y W n o s k c a e g a t s o P . s . u P W L s n o i t a c i L b u d L r o s r e g g o d t s t r s r P 2 2 a normally excellent was a source of pride and satisfaction to me was breakfast that my wife our outdoor fireplace. i had hauled some of the creates on a campfire) i rock in that superior fire pit some fifty miles. un - planned the coming day. fortunately the trailer bumped into it and scat - 3 at the same time i tered rocks and fire more than a little bit. after 1 0 2 sort of suspicioned that i putting the fire out had to tear down the fireplace y was kidding myself. and throw the carefully selected rocks into a pile. R Rigging a thoughts kept intrud - then with no further trouble we were out and on U N ing, thoughts like; "got our way. a J to get these 20 plus rolls We deliberately wasted time going out. We had Shack of film back so that John about 25 miles to go to the junction and then 52 (darkroom man par ex - miles from the junction to kitwanga, all on pri - “Classic” cellence) can develop the vate road.
    [Show full text]
  • Operational Parameters of Logging Trucks Working in Mountainous Terrains of the Western Carpathians
    Article Operational Parameters of Logging Trucks Working in Mountainous Terrains of the Western Carpathians Michal Allman 1, Zuzana Dudáková 1,*, Martin Jankovský 2 and Ján Merganiˇc 1 1 Department of Forest Harvesting, Logistics and Ameliorations, Faculty of Forestry, Technical University in Zvolen, T.G. Masaryka 24, 960 01 Zvolen, Slovakia; [email protected] (M.A.); [email protected] (J.M.) 2 Department of Forestry Technology and Constructions, Faculty of Forestry and Wood Sciences, Czech University of Life Sciences Prague, Kamýcká 129, 165 00 Prague 6–Suchdol, Czech Republic; jankovskym@fld.czu.cz * Correspondence: [email protected]; Tel.: +421-455-206-276 Abstract: Timber haulage is the last phase of the raw timber production process, necessary to transport timber to the customer. To improve the efficiency of logging truck operations, it is necessary to observe and assess several operational parameters through the electronic systems installed on the logging trucks. Measurements for this study were conducted for three logging truck types, which hauled 24,648 m3 of timber over 54,857 km and 1232 round trips. The RMC system was used for truck monitoring, equipped with a CAP04 capacitance sensor and a WGS 48 GPS module. The monitoring was continuous, lasting 27 to 74 weeks. Data acquired were evaluated via regression and correlation analyses and ANOVA. The results showed a moderately strong negative correlation between haulage productivity and haulage distance, ranging from r = −0.47 to r = −0.68. Simultaneously, a rather low efficiency of timber haulage was found for long-range haulage caused by legislation-based small utilization of the load-carrying capacity of the logging trucks.
    [Show full text]
  • LOGGING and LOG TRANSPORT in TROPICAL HIGH FOREST Log Extraction in Waterlogged Areas by Means of Blasted Ditches, Surinam
    rv0D AND AGRICULTURE ORGANIZATION OF THE UNITED NATIONS As recorded information on methods, production and costs of logging and transport in the developing world - and especially in tropical high forest - is scarce, one of the main purposes· of this manual is to focus attention on the analytic approach needed to quantify output and costs data. An important element of tropical high forest logging is examined: the influence of physical and economic conditions on production. Production and cost data are presented, as far as available information permits, for the most commonly used logging methods adaptable to this. particular situation. LOGGING AND LOG TRANSPORT IN TROPICAL HIGH FOREST Log extraction in waterlogged areas by means of blasted ditches, Surinam. (Bubberman/Vink) FAO Forestry Development Paper No. 18 LOGGING AND LOG TRANSPORT IN TROPICAL HIGH FOREST A manual on production and costs FOOD AND AGRICULTURE ORGANIZATION OF THE UNITED NATIONS Rome, 1974 The copyright in this book is vested in the Food and Agri­ culture Organization of the United Nations. The book may not be translated, nor may it be reproduced, in whole or in part, by any method or process, without written permission from the copyright holder. Applications for such permis­ sion, with a statement of the purpose and extent of the reproduction desired, should be addressed to The Director, Publications Division, Food and Agriculture Organization of the United Nations, Via delle Terme di Caracalla, Rome, Italy. @ FAO 1974 Printed in Italy CONTENTS Introduction . 1 PURPOSE OF THE STUDY 1 SOURCES OF INFORMATION 2 Field studies - Questionnaires - Literature 1. Theoretical framework . 4 SELECTION OF FACTORS AFFECTING PRODUCTION 4 LIMITATIONS OF THE STUDY .
    [Show full text]