DOCSLIB.ORG

Drive-At001 -En-P.Pdf

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Drive-At001 -En-P.Pdf Table of Contents Section 1 – Motor and Load Basics.................................................................................................... 9 AC Motors........................................................................................................................................... 11 NEMA Design Types........................................................................................................................ 12 Motor Synchronous Speed............................................................................................................... 12 3-Phase Motor Connections - NEMA ............................................................................................... 13 Rotor Inertia – NEMA....................................................................................................................... 16 3-Phase Motor Connections – IEC Nomenclature............................................................................ 17 Rotor Inertia – IEC ........................................................................................................................... 18 AC Motor Operation above Base Speed .......................................................................................... 19 Synchronous Motors........................................................................................................................ 20 Wound Rotor.................................................................................................................................... 20 Linear Induction Motors ................................................................................................................... 21 DC Motors........................................................................................................................................... 22 Design Types (typical characteristics).............................................................................................. 22 Operation above Base Speed.......................................................................................................... 23 DC Motor Control Basics ................................................................................................................. 24 Armature-Voltage Control ................................................................................................................... 24 Shunt-Field Control ........................................................................................................................... 24 Combination Control.......................................................................................................................... 24 Operation with Variable Speed Drive ..................................................................................................... 24 Load Types......................................................................................................................................... 25 Constant Torque Load ..................................................................................................................... 25 Variable Torque Load ...................................................................................................................... 25 Constant Horsepower Operation...................................................................................................... 26 Overload Operation.......................................................................................................................... 26 AC Drive Power Structure ................................................................................................................. 27 Regeneration...................................................................................................................................... 29 Stored Energy.................................................................................................................................. 29 Linear........................................................................................................................................... 30 Overhauling Load ........................................................................................................................ 30 Braking ............................................................................................................................................ 30 Line Regeneration............................................................................................................................ 30 Regenerative Brake ..................................................................................................................... 30 Drive Application Engineering Engineering Handbook Active Converter .......................................................................................................................... 31 Four Quadrants of Operation ....................................................................................................... 31 Section 2 – Basic Physics ................................................................................................................. 33 SI Units (International System of Units)........................................................................................... 34 Mechanical Quantities...................................................................................................................... 34 Electrical Quantities ......................................................................................................................... 35 Formulas............................................................................................................................................. 36 Mechanical....................................................................................................................................... 36 Linear Motion............................................................................................................................... 36 Rotational Motion......................................................................................................................... 37 Kinetic energy for Rotational Motion ............................................................................................38 Moment of Inertia......................................................................................................................... 39 Power .......................................................................................................................................... 40 Electrical .......................................................................................................................................... 42 Ohms Law ................................................................................................................................... 42 Angular frequency........................................................................................................................ 42 Impedance................................................................................................................................... 42 Power .......................................................................................................................................... 42 Power Factor ............................................................................................................................... 43 3-Phase relationships .................................................................................................................. 43 Imperial Units ..................................................................................................................................... 44 Mechanical....................................................................................................................................... 44 Linear Motion............................................................................................................................... 44 Rotational Motion......................................................................................................................... 45 Kinetic Energy.............................................................................................................................. 46 Moment of Inertia......................................................................................................................... 47 Electrical .......................................................................................................................................... 48 Power .......................................................................................................................................... 48 Newton’s laws of motion................................................................................................................... 48 Mass and weight.............................................................................................................................. 48 Lifting.................................................................................................................................................. 49 Friction ............................................................................................................................................... 49 Torque ................................................................................................................................................ 50 Torque and Tension..........................................................................................................................
Load more

Recommended publications
  • Development of a Self-Powered Weigh-In- Motion System
    Development of a Self-Powered Weigh-in- Motion System Project No. 19ITSUTSA01 Lead University: University of Texas at San Antonio Final Report December 2020 Disclaimer The contents of this report reflect the views of the authors, who are responsible for the facts and the accuracy of the information presented herein. This document is disseminated in the interest of information exchange. The report is funded, partially or entirely, by a grant from the U.S. Department of Transportation’s University Transportation Centers Program. However, the U.S. Government assumes no liability for the contents or use thereof. Acknowledgements The authors would like to acknowledge the support by the Transportation Consortium of South- Central States (TranSET) i TECHNICAL DOCUMENTATION PAGE 1. Project No. 2. Government Accession No. 3. Recipient’s Catalog No. 19ITSUTSA01 4. Title and Subtitle 5. Report Date Dec. 2020 Development of a Self-Powered Weigh-in-Motion System 6. Performing Organization Code 7. Author(s) 8. Performing Organization Report No. PI: A.T. Papagiannakis https://orcid.org/0000-0002-3047-7112 Co-PI: Sara Ahmed https://orcid.org/0000-0003-0935-5011 Co-PI: Samer Dessouky https://orcid.org/0000-0002-6799-6805 GRA: Reza Khalili https://orcid.org/0000-0002-8383-4945 GRA: Gopal Vishwakarma https://orcid.org/0000-0002-5440-9149 9. Performing Organization Name and Address 10. Work Unit No. (TRAIS) Transportation Consortium of South-Central States (Tran-SET) University Transportation Center for Region 6 11. Contract or Grant No. 3319 Patrick F. Taylor Hall, Louisiana State University, Baton Rouge, 69A3551747106 LA 70803 12. Sponsoring Agency Name and Address 13.
    [Show full text]
  • Lci's and Synchronous Motors Applied to Roller Mills
    LCI'S AND SYNCHRONOUS MOTORS APPLIED TO ROLLER MILLS For Presentation at the IEEEIPCA Cement Industry Technical Conference Salt Lake City, UT May 2000 By: James F. Zayechek G E Industrial Systems 1. Abstract A cement company concerned about high power-factor penalty costs requested an evaluation of the feasibility of using synchronous motors starting through LCl's to drive three new roller mills at a cement plant. The prior experience with roller mills centered about the application of wound rotor induction motors with either cascaded secondary resistance or liquid rheostat. By utilizing synchronous motors, there was the possibility of providing leading power factor to reduce the reactive power demands seen by the utility feeding the cement plant. It was theorized that, if sufficient power factor correction could be obtained, the payback period of the incremental additional cost of the synchronous motor drive system would be very short. After payback of the initial investment, all future energy savings gravitate directly to the bottom line as additional revenue. Several key concerns had to be addressed in evaluating the use of synchronous motors for these relatively high starting torque requirement applications. This paper discusses the electrical and mechanical evaluation leading up to the decision to proceed with this new application of synchronous motors started through an LCI. 2. Introduction Roller mills, also known as vertical mills, are becoming more prevalent in modern cement plants. These mills have application both for raw material preparation and clinker grinding to final specifications. The increasingly competitive nature of today's business environment is pushing the mill OEM's to larger mills with greater throughput.
    [Show full text]
  • Power Processing, Part 1. Electric Machinery Analysis
    DOCONEIT MORE BD 179 391 SE 029 295,. a 'AUTHOR Hamilton, Howard B. :TITLE Power Processing, Part 1.Electic Machinery Analyiis. ) INSTITUTION Pittsburgh Onii., Pa. SPONS AGENCY National Science Foundation, Washingtcn, PUB DATE 70 GRANT NSF-GY-4138 NOTE 4913.; For related documents, see SE 029 296-298 n EDRS PRICE MF01/PC10 PusiPostage. DESCRIPTORS *College Science; Ciirriculum Develoiment; ElectricityrFlectrOmechanical lechnology: Electronics; *Fagineering.Education; Higher Education;,Instructional'Materials; *Science Courses; Science Curiiculum:.*Science Education; *Science Materials; SCientific Concepts ABSTRACT A This publication was developed as aportion of a two-semester sequence commeicing ateither the sixth cr'seventh term of,the undergraduate program inelectrical engineering at the University of Pittsburgh. The materials of thetwo courses, produced by a ional Science Foundation grant, are concernedwith power convrs systems comprising power electronicdevices, electrouthchanical energy converters, and associated,logic Configurations necessary to cause the system to behave in a prescribed fashion. The emphisis in this portionof the two course sequence (Part 1)is on electric machinery analysis. lechnigues app;icable'to electric machines under dynamicconditions are anallzed. This publication consists of sevenchapters which cW-al with: (1) basic principles: (2) elementary concept of torqueand geherated voltage; (3)tile generalized machine;(4i direct current (7) macrimes; (5) cross field machines;(6),synchronous machines; and polyphase
    [Show full text]
  • Dynamic Suspension Modeling of an Eddy-Current Device: an Application to Maglev
    DYNAMIC SUSPENSION MODELING OF AN EDDY-CURRENT DEVICE: AN APPLICATION TO MAGLEV by Nirmal Paudel A dissertation submitted to the faculty of The University of North Carolina at Charlotte in partial fulfillment of the requirements for the degree of Doctor of Philosophy in Electrical Engineering Charlotte 2012 Approved by: Dr. Jonathan Z. Bird Dr. Yogendra P. Kakad Dr. Robert W. Cox Dr. Scott D. Kelly ii c 2012 Nirmal Paudel ALL RIGHTS RESERVED iii ABSTRACT NIRMAL PAUDEL. Dynamic suspension modeling of an eddy-current device: an application to Maglev. (Under the direction of DR. JONATHAN Z. BIRD) When a magnetic source is simultaneously oscillated and translationally moved above a linear conductive passive guideway such as aluminum, eddy-currents are in- duced that give rise to a time-varying opposing field in the air-gap. This time-varying opposing field interacts with the source field, creating simultaneously suspension, propulsion or braking and lateral forces that are required for a Maglev system. In this thesis, a two-dimensional (2-D) analytic based steady-state eddy-current model has been derived for the case when an arbitrary magnetic source is oscillated and moved in two directions above a conductive guideway using a spatial Fourier transform technique. The problem is formulated using both the magnetic vector potential, A, and scalar potential, φ. Using this novel A-φ approach the magnetic source needs to be incorporated only into the boundary conditions of the guideway and only the magnitude of the source field along the guideway surface is required in order to compute the forces and power loss.
    [Show full text]
  • A Survey of Propulsion Systems for High Capacity Personal Rapid Transit
    T NO UMTA-MA-06-0 04 8-75-2 A SURVEY OF PROPULSION SYSTEMS FOR HIGH CAPACITY PERSONAL RAPID TRANSIT Thorleif Knutrud JULY 1975 FINAL REPORT DOCUMENT IS AVAILABLE TO THE PUBLIC THROUGH THE NATIONAL TECHNICAL INFORMATION SERVICE, SPRINGFIELD VIRGINIA 22161 Prepared for u.s. DEPARTMENT OF TRANSPORTATION URBAN MASS TRANSPORTATION ADMINISTRATION Office of Research and Development Washington DC 20590 . NOTICE This document is disseminated under the sponsorship of the Department of Transportation in the interest of information exchange. The United States Govern- ment assumes no liability for its contents or use thereof NOTICE The United States Government does not endorse products or manufacturers. Trade or manufacturers' names appear herein solely because they are con- sidered essential to the object of this report. 7 , Htr . /V3 a/c? “DOT - Tsc- u. ~7&~ /£“ TECHNICAL REPORT STANDARD TITLE RAGE 3. Recipient's Catalog No. 1 . Report No. 2. Government Accesnon No. UMTA-MA- 0 6- 0 048-75-2 5. Report Date 4. T i tie and Subtitle July 1975 A SURVEY OF PROPULSION SYSTEMS FOR 6. Performing Organization Code HIGH CAPACITY PERSONAL RAPID TRANSIT 7. Author's) 8. Peefarming Orgonrzatron Report No Thorleif Knutrud DOT -TSC -UMTA-7 5-15 9. Performing Organization Name and Address 10. Work Unit No UM533/R6751 Alexander Kusko, * Inc.* 11. Controct or Grant No 161 Highland Avenue DOT -TSC- 2 03/DOT- TSC- 965 Needham Heights MA 02194 15. 13. Type of Report and Period Covered 12. Sponsoring Agency Nome ond Address Final Report U.S. Department of Transportation July 1974 - June 1975 16.Urban Mass Transportation Administration Office of Research and Development 14.
    [Show full text]
  • One Stop | Directories | Search U of M View All Past Issues of Brief Vol
    Return to: University Relations : U of M Home One Stop | Directories | Search U of M View all past issues of Brief Vol. XXXI No. 1 • January 10, 2001 Editor: Pauline Oo, 612-624-7889, [email protected] Past issues President Yudof talked about "special aspects that differentiate the U" from other state higher education institutions to House Higher Education Committee Jan. 8. Discussion included funding sources, expenditures, and enrollment and employment statistics. Presentation is available at www.umn.edu/govrel. Presentation to Senate Higher Education Budget Division will be Jan. 22, 1 p.m., State Capitol. President-elect Bush has named Yudof to his 31-member transition advisory committee on education. "Education policy and reform are longtime interests of mine," said Yudof, "and I look forward to discussing these critical issues with those charged with setting our nation's policies." Bush has named 475 individuals, including Minnesotans Yudof and Gov. Ventura, to work on 15 committees. Provost Bruininks has been appointed to Governor's Workforce Development Council. Group advises governor on workforce development policies and plans strategies associated with Minnesota's workforce. Recent gift of $10 million to Minnesota Landscape Arboretum is largest in its 42-year history. Arboretum, part of the Department of Horticultural Science, will use the gift from an anonymous donor to build new Visitor Center. Center will serve as formal entry point to gardens and collections; projected opening is 2004. Preliminary findings on unauthorized use of U long-distance telephone access code by 13 Gopher football student-athletes and other U students were released Dec. 20.
    [Show full text]
  • H, SAY Plied, Sternly
    B uchanan Record. PUBLISHED EVERY THURSDAY ---- »Y---- ID. ZBL. B O W E B . TERMS Sl.OO PER YEAR PATASLS IX ADYASOT. BELLS NEWS, IU , SCB3CKIPTIOXS DISCONTINUED AT EXPIRATION. SELLS BOOKS, ADVERTISING RATES. VOLUME XXXI, BLCHAXAX, BEERIEX COUNTY, MICHIGAN, THURSDAY, OCTOBER 21, 1S97, NUMBER 39. LESS THAU ONE YEAR. One week........................... S -SO pet incA SELLS GUM* One month. ............ .90 “ Two m onths....... .......... 1.50 “ “ iVe- are all friends,” the man said Three m onths......................... 2.10 ‘ ‘ fiY.Yn’mfkY.Y again, as his head reached below the asked Zfaeltson, in derisive tones. j melange Six montha......................... S.40 “ HUMPHREYS’ level of the floor. Dim though the light MICHIGAS . YEARLY CONTRACTS. I “By denouncing' you,” Mr. Slorley re­ was upon the stairs, I recognized him One inch, $6.00 foe year o£ 5i Insertions. N o. 1 Cures Fever. A CLEW BY WIRE H, SAY plied, sternly. NEWS OF GENERA'- INTEREST TO OUR Two inches or over, $5.00 per inch, for year of « immediately, and with a loud call N o. 2 W o r m ', 5S insertions. Or, An Interrupted Current. j “Now, that is useless and foolish talk. sprang toward him. READERS. One column, $120 for year of 52 insertions. te N o. S Infants’ Diseases. Bet us reason, as between tw o business “Afr. Perry! Oh, thank God, you Celebrated Sleeping Car Magnate W on ’t you come to t t men,” said Jackson, assuming a confi­ > PP lr B—In Record Buildine.Oak Street N o. 4 Diarrhea. BY HOWARD M. YOST. have come!” I stepped unthinkingly Important Happenings in the State Daring Is No More.
    [Show full text]
  • Resistor Control of Wound Rotor Motors Resistor Control of Wound Rotor Motors
    RESISTOR CONTROL OF WOUND ROTOR MOTORS RESISTOR CONTROL OF WOUND ROTOR MOTORS The Wound Rotor Induction Motor or Slip Ring Motor is widely used for applications requiring speed control or low starting currents. It is very similar to the Squirrel Cage Induction Motor except that the rotor leads are brought out through slip rings (commutator rings) so that external resistance may be inserted. In fact, if we shorted these three rotor leads together, we would basically have a squirrel cage motor. The beauty of the WRM is that we can control the torque of the motor with external resistors. The purpose of this paper is to show how these resistors are sized and connected for simple speed control or starting duty. STATIR CIRCUIT The Stator, or stationary winding, of the WRM is a three-phase winding which has a cylindrical shape and occupies the outer part of the motor just inside of the motor frame. The three primary leads are usually connected (through a contactor) to the 460 VAC 3ph, 60hz power lines. The three- phase power, applied to the stator windings, produces a rotating magnetic field. The mathematics are complex and will not be covered here. The main thing to remember is that a constantly rotating magnetic field is produced whenever the stator is energized. The speed or RPM of this rotating magnetic field is a function of how many “poles” are created by the windings and the frequency of the incoming power (60 cycles per second in this country, 50 cycles per second in many European countries). With 60hz power, this synchronous RPM is a multiple of 60 such as 360, 900, 1800, etc.
    [Show full text]
  • ADJUSTABLE SPEED DRIVES By: Richard D
    Service Application Manual SAM Chapter 620-130 Section 6A ADJUSTABLE SPEED DRIVES By: Richard D. Beard P.E. Consultant, RSES Manufacturers’ Service Advisory Council INTRODUCTION Many commercial and industrial machines and processes require adjustable speed. Adjustable speed usually makes a machine more universally compatible and increases its versatility. Adjustable-speed drives also are being used in residential equipment, including air conditioners, refrigerators, heat pumps, furnaces, and other devices driven by motors. These drives optimize speed and torque, making them generally more efficient than non-adjustable-speed drives. An adjustable-speed motor is one in which the speed can be varied gradually over a wide range—but, once adjusted, it remains nearly unaffected by the load. A variable-speed motor is one in which the speed varies with the load, usually decreasing when the load increases. The term "adjustable speed" implies that some external adjustment, which is independent of load, will cause the speed to change. A variable-frequency inverter drive is an example. The term "variable speed" describes a drive in which load changes inherently cause significant changes in speed. A direct current series motor, for example, exhibits this characteristic. An adjustable variable-speed motor is one in which the speed can be adjusted gradually. However, once adjusted for a given load, the speed will vary with changes in the load. A multispeed motor is one that can be operated at any one of two or more definite speeds, each being practically independent of the load. The multispeed motor is neither an adjustable-speed nor a variable-speed drive. Multispeed motors usually have two, three, or four definite operating speeds.
    [Show full text]
  • British Troops in Londonderry a Toast to Three Men Who Left Sky Unlimited
    * N '. ' a ^ PAGE THIRTY’-SIX ' ■■ ' ‘ \ llanrbfHtpr €t>ratng iii^raib WEDNESDAY, AUGUST 18, 1969 Most Manchester Stores Open Tonight Until 9 O^Clock will be borne by the town, prin­ Town^ T ravelers Research cipally by in-kind services. Harkins, following the sign­ Av«rage Daily Net Press Run ing of the contract with Trav­ Sign C-DAP Study Contract elers, said that work on the Fbr nSe Week Ended The Weather C-DAP study will start im­ June M, IMS ^ J / contract waa signed In Harkins added, however, that mediately. Fair and mild .tonight with // tford txiday (or the services he anticipates that 'Travelers lows in the 60s. Tomorrow, / ■ of ^y^elers Research Corp., to will do a good job and that he 15,459 again, (air and warm with does not anticipate any need highs in upper 80s. be the o<™ultant for Manches­ Five-Day Forecast for cancellation WINDSOR LOCKS, Conn. Manchester— A City of Vitiate Charm ter’s two^ar C-DAP (Com­ C-DAP, which can be com­ (AP) — Temperatures In Con­ VOL. LXXXV m , NO. 268 munity DevfelQpment Action pared to jet^massive Comprehen­ necticut from ’Thursday through TWENTY-TWO PAGES MANCHESTER, CONN., THURSDAY, AUGUST 14, 1969 (CSaaatfted Ads-ertising on Ftage 19) PRICE TEN CENTS Plan) study. sive P,lah, is a two-year study Monday are expected to average Signing for the tmVh was Ly­ ot a town’s exlstlng/servlces near normal with daytime highs man Hoops, chalrmaiAof Man­ and facilities and a ^'projection from 80 to 86 and overnight chester’s C-DAP AgencjAx^l^ of its needs in the five-year lows in the 60s.
    [Show full text]
  • The American Legion Magazine [Volume 87, No. 5 (November 1969)]
    THE AMERICAN 20C.N0VEMBER1969 LEGIONMAGAZINE The Growing Problems of AUTO DEFECTS AND REPAIRS — aris 10 Faimkm French PERFUMES ^^^^^ 10 world famous fragrances ^4.95 PARISIAN A SCENT FOR EVERY MOOD An extravagant, exciting gift at an unbelievably low price. Each in its own distinctive bottle and set You save when buying gift package of 10. in a beautiful tri-color gift box decorated $10.00 Our price, $1.50 for each bottle if bought separately. with gay, crisp drawings of Paris. These are all genuine full strength perfumes, We have imported a limited number of not toilet water or cologrie. these exciting gift packages for distribu- All perfumes sealed in the beautiful bottles you see pictured here. tion in the United States and Canada. Please rush your order now while the MOIMEY BACK C3UARAIMTEE supply lasts. Upon receipt of your order Niresk Importers, Dept. PR-132 we will rush this amazing gift package of 210 S. DesPlaines St., Chicago, HI. 60606 10 world famous French fragrances, each Please rush at once the fabulous collection of 10 World Famous Fragrance perfumes for only $4.95 each set plus for postage, handling and in its own different, distinctive bottle — 25C insurance—on full money-back guarantee. all for only $4.95. must You be completely I enclose $_ delighted or your money back promptly. Ship C.O.D. plus postage & C.O.D. fees. Charge to my Diners' Club Acct. No Please do not delay. Mail the no-risk Charge to my American Express Acct. No.. coupon today while our supply lasts.
    [Show full text]
  • Design Approach to a Wound Rotor Induction Motor Towards Optimization
    ISSN (Online) : 2454 -7190 ISSN (Print) 0973-8975 J.Mech.Cont.& Math. Sci., Vol.-13, No.-3, July-August (2018) Pages 159-172 Design approach to a wound rotor induction motor towards optimization 1Pritish Kumar Ghosh, 2Pradip Kumar Sadhu, 3Amarnath Sanyal, *4DebabrataRoy, 5Biswajit Dutta 1,2Electrical Engineering, Indian Institute of Technology (Indian School of Mines), Dhanbad, 826004, India 3Ex Power Engineering, Jadavpur University, Kolkata,W.B.- 700032,India 4Electrical Engineering,Techno International Batanagar, South 24Parganas, W.B.- 700141,India 5ElectricalEngineering,Seacom Engineering College,Howrah,W.B.-711302,India [email protected],[email protected],3ansanyal@yahoo. co.in,[email protected],[email protected], *Corresponding author: Debabrata Roy, Abstract About 88% of the driving power is produced by 3-phase and single-phase induction motors. In most part it is by squirrel-cage motors, only a small fraction by the slip-ring or phase-wound type. It is because the cage-type motors are relatively inexpensive. But they suffer from low p.f. operation and low starting torque which cannot be manipulated by inserting resistance in the rotor circuit. Also, this type of induction motors is not easily speed-adjustable. Though a little more expensive, the slip-ring type induction motors do not have these disadvantages. Therefore, they are used as speed-adjustable drives and for drives where heavy duty starting is involved. The design of any kind of power equipment should be made cost-optimally in the present day competitive market. A new approach to reaching optimal solution has been shown in this paper by the method of sequential searching with respect to the chosen design variables.
    [Show full text]