UNITED NATIONS INDUSTRIAL DEVELOPMENT ORGANIZATION

VIENNA INTERNATIONAL CENTRE PO BOX 300, A-1400, VIENNA, AUSTRIA TELEPHONE: (+43 1) 26026-0 FAX: (+43 1) 26026-6815

Technical specifications the procurement of Workshop Equipment Project SAP No.: 101100 Rfx 700001532 I. . General Background Information:

The purpose of this procurement is to purchase equipment for the implementation of UNIDO training activities in General Mechanics/.

II. The Scope of Supply:

UNIDO REQUIREMENTS TO BE COMPLETED BY THE INVITEE

Item Name and required parameter QTY Unit price Total item compliance* Remarks** No price currency currency yes/no Workshop Equipment US $ US $ 1 Workbench/workstation 5 0.00 0.00 Y/N  Flat packed workbench/work station – 1.2 metres wide  Worktop size approx. 1205 x 600mm  Boltless designed frame, easy to assemble with minimal being required  Two half drawers, with ball bearing slides, full size shelf below worktop and 230mm shelf above pegboard.  Pegboard rear panel with hooks for convenient storage. 2 Bench vice (engineers) 5 . 4” (100mm) opening bench vice . 3” (75mm) jaw width . Premium quality bench vice with replaceable jaws 3 Bench vice jaws 2 . Set of 75mm jaws for above bench vice sets 4 Mild steel sheet 5 . 1.2–1.5mm mild steel sheet cut to workbench worktop pcs (item 1) size e.g. 1205 x 600mm. Shall be affixed to the wooden top of bench to protect surface. 5 Toolkit for Metalworking 5 A set of tools for basic metalworking comprising of : sets . ONE (1) x 12” . TEN (10) x hacksaw blades 12” x 18 teeth per inch . TEN (10) x hacksaw blades 12” x 32 teeth per inch

Page 1 of 4

UNITED NATIONS INDUSTRIAL DEVELOPMENT ORGANIZATION

VIENNA INTERNATIONAL CENTRE PO BOX 300, A-1400, VIENNA, AUSTRIA TELEPHONE: (+43 1) 26026-0 FAX: (+43 1) 26026-6815

Technical specifications the procurement of Workshop Equipment Project SAP No.: 101100 Rfx 700001532 . ONE (1) x junior hacksaw 6” . TEN (10) x junior hacksaw blades 6” x 32 teeth per inch . ONE (1) x 6 piece needle file set, 16cm long, plastic handles . ONE (1) x 4 piece engineers file set, 25cm long, moulded plastic handles . ONE (1) x 3m tape measure . ONE (1) x 300mm steel ruler, round end, hanging hole . ONE (1) x protractor type angle gauge . ONE (1) x double end metal scriber . ONE (1) x metric pitch gauge . ONE (1) x 13 piece metric feeler gauge . ONE (1) x 4mm square head centre punch, 100mm long . ONE (1) x 2.8-5mm engineers tap wrench . ONE (1) x M8 x 1.25 tap set (taper, second and plug) . ONE (1) x 25mm die stock handle . ONE (1) x M8 x 1.25 split die . ONE (1) x plastic handle gasket scraper set (3 or 4 pcs) . ONE (1) x spark brush set (3 pcs) . ONE (1) x stainless steel wire brush . ONE (1) x 150mm engineers square . ONE (1) x 200mm spring divider . ONE (1) x 1lb engineers ball pein hammer . TWO (1) x 255mm curved jaw grip wrench . ONE (1) x 160mm combination plier . ONE (1) x 125cc metal oil can . ONE (1) x plastic handle dustpan/brush set . Toolbox is not required as tools will be fixed to back board 6 set 1 . Metric tap and die set, M2 through to M16 . High speed steel

7 Screw Extractor 1 . 4 piece screw extractor set (2, 3, 4 and 5)

8 Thread restorer 1 . Metric thread restorer file

9 Wire wool 1 Page 2 of 4

UNITED NATIONS INDUSTRIAL DEVELOPMENT ORGANIZATION

VIENNA INTERNATIONAL CENTRE PO BOX 300, A-1400, VIENNA, AUSTRIA TELEPHONE: (+43 1) 26026-0 FAX: (+43 1) 26026-6815

Technical specifications the procurement of Workshop Equipment Project SAP No.: 101100 Rfx 700001532 . 450g roll of wire wool, Grade 2

10 Wire wool 1 . 450g roll of wire wool, Grade 0

11 Bench grinder with pedestal stand 1 . 150mm bench grinder, 230V UK plug . Floor mounted pedestal type

12 Step . Sheet metal step drill (4-20mm) 1

13 Drill sharpener and wheel 1 . 3-13mm drill sharpener for use with power tool drill . Complete with TWO (2) silicon carbide sharpening wheels

14 Pillar drill . Floor standing pillar drill 1 . Approximately 550W 230V with 13 amp UK plug . Titling worktable . Spindle taper: MT2 . Chuck: 16mm . Drill capacity: 20mm . Spindle travel: 80mm . Speeds: 12 . Max distance - chuck/table: 725mm . Max distance - chuck/base: 1220mm . Max distance - spindle to column: 190mm . Column diameter: 80mm . Table size: 300 x 300mm . Base size: 500 x 300mm

15 Morse taper drill drift 1 . ONE (1) x morse taper drill drift tool, size 1 & 2 16 Morse taper sleeve 1 . 1 x 2MT (inside x outside) morse taper sleeve

Page 3 of 4

UNITED NATIONS INDUSTRIAL DEVELOPMENT ORGANIZATION

VIENNA INTERNATIONAL CENTRE PO BOX 300, A-1400, VIENNA, AUSTRIA TELEPHONE: (+43 1) 26026-0 FAX: (+43 1) 26026-6815

Technical specifications the procurement of Workshop Equipment Project SAP No.: 101100 Rfx 700001532 17 Drill press vice 1 . 100mm jaw width drill press vice 18 Bench shear 1 . 4mm plate bench shear . 120mm jaw width 19 Morse taper drill set 1 HSS taper shank drill set – metric, comprising of . ONE (1) x 3mm MT1 . ONE (1) x 4mm MT1 . ONE (1) x 5mm MT1 . ONE (1) x 6mm MT1 . ONE (1) x 7mm MT1 . ONE (1) x 8mm MT1 . ONE (1) x 9mm MT1 . ONE (1) x 10mm MT1 . ONE (1) x 11mm MT1 . ONE (1) x 12mm MT1 . ONE (1) x 13mm MT1 . and . ONE (1) x 14mm MT2 . ONE (1) x 15mm MT2 . ONE (1) x 16mm MT2 . ONE (1) x 17mm MT2 . ONE (1) x 18mm MT2 . ONE (1) x 19mm MT2 . ONE (1) x 20mm MT2 . ONE (1) x 21mm MT2 . ONE (1) x 22mm MT2 . ONE (1) x 23mm MT2

20 Manual sheet metal folder 1 . Sheet Metal Folder . Bench Mounting 760mm width . 17 gauge (1.3mm thickness approx.)

21 Drill chuck 1 . ½” x 20 industrial keyed drill chuck (1.5 to 13mm)

Page 4 of 4

UNITED NATIONS INDUSTRIAL DEVELOPMENT ORGANIZATION

VIENNA INTERNATIONAL CENTRE PO BOX 300, A-1400, VIENNA, AUSTRIA TELEPHONE: (+43 1) 26026-0 FAX: (+43 1) 26026-6815

Technical specifications the procurement of Workshop Equipment Project SAP No.: 101100 Rfx 700001532 22 Drill chuck arbor 1 . MT2 drive to ½” x 20 thread chuck 23 HSS Tin tipped drill set 3 . TWENTY FIVE (25) pc set, 1 to 13mm in 0.5mm increments

24 Countersink drill 2 . 10mm HSS countersink drill 25 Centre drill set 2 . FIVE (5) peice metric centre drill set in HSS . 2-5mm pilot / 5-12.5mm body

26 Hex key set 2 . TWENTY (20) piece metric hexagon (allen) key set . 1.5-10mm size range

27 Nuts, bolts and washers sets 2 . ONE (1) x set of nuts, bolts and washers comprising of : . Hex nuts: 75 x M6, 30 x M8 and 20 x M10. . Washers: 150 x M6, 60 x M8 and 50 x M10. . Set : 30 x (M6 x 16), 20 x (M6 x 20), 20 x (M6 x 25), . 10 x (M8 x 30), 10 x (M8 x 40), 5 x (M8 x 50), . 10 x (M10 x 60), 6 x (M10 x 70) and 4 x (M10 x 75) 28 Tin snips 2 . THREE (3) piece aviation tin snips . right hand, left hand and straight cutting

29 Pin punch set 1 . SIX (6) piece parallel pin punch set . 2, 3, 4, 5, 6 and 8mm

30 Cold chisel set 1 . THREE (3) piece flat cold chisel set . 12x150mm, 18x200mm and 25 x 255mm

Page 5 of 4

UNITED NATIONS INDUSTRIAL DEVELOPMENT ORGANIZATION

VIENNA INTERNATIONAL CENTRE PO BOX 300, A-1400, VIENNA, AUSTRIA TELEPHONE: (+43 1) 26026-0 FAX: (+43 1) 26026-6815

Technical specifications the procurement of Workshop Equipment Project SAP No.: 101100 Rfx 700001532 31 Pliers set 1 . FOUR (4) piece plier set . Groove joint 265mm, snipe nose 215mm, diagonal 165mm and combi-plier 200mm (approx. sizes only)

32 Micrometer and caliper set 1 . Basic precision measuring set supplied in plastic fitted case: ONE (1) x 0 - 25mm and ONE (1) 25 - 50mm external micrometer, ONE (1) x 25mm setting standard, TWO (2) x micrometer setting spanners, ONE (1) x 125mm/5” vernier caliper and ONE (1) x 150mm/6” rule. 33 Spring caliper set 1  ONE (1) x 200mm internal spring caliper.  ONE (1) x 200mm external spring caliper.

34 Clear acrylic sheet 30 . 2mm clear acrylic sheet, cut to 610 x 910mm and drilled with FOUR corner holes at minimum 13mm from edges, diameter of holes 5mm.

35 Clear acrylic sheet 10 . 2mm clear acrylic sheet, cut to 840 x 1190mm and drilled with FOUR corner holes at minimum 13mm from edges, diameter of holes 5mm and TWO holes on each side spaced equidistant along the edges, at minimum 13mm from edges, diameter of holes 5mm.

36 A4 picture frames 40  10-15mm wide flat black brushed grain finish picture frames to accept A4 size photographs/prints. Each frame to be supplied with 1.2mm Acrylic glazing.

37 Door signs 20  Rigid PVC, self adhesive backed (foam pads or peel off in back), total 1-2mm thickness in WHITE, printed with 5 spot colours with no bleed over edges.

Page 6 of 4

UNITED NATIONS INDUSTRIAL DEVELOPMENT ORGANIZATION

VIENNA INTERNATIONAL CENTRE PO BOX 300, A-1400, VIENNA, AUSTRIA TELEPHONE: (+43 1) 26026-0 FAX: (+43 1) 26026-6815

Technical specifications the procurement of Workshop Equipment Project SAP No.: 101100 Rfx 700001532 ONE pc each of TWENTY different designs (similar to this design)

38 Safety spectacles 20  Anti-mist safety spectacles, one piece polycarbonate lens  Rubber nose bridge and spectacle cord

39 Pegboard tool hanging hooks 5  Must be compatible with Item 1 workbench perfo board. sets  Quantity: 50 pcs in a set (various sizes)

Total price EX-Works packed for AIR shipment : US $

Total price CPT Erbil airport, IRAQ : US $ International bidders

Total price DDP Erbil (to the S.A.T. Runaky Quarter), IRAQ : US $ Iraqi bidders

*) compliance must be confirmed in detail by the contractor’s offer and technical documentation and will be verified by UNIDO during technical evaluation; **) if not compliant with UNIDO’s required parameters, the invitee must indicate his parameters in this column

Company Name of Bidder : ______Contact person : ______Page 7 of 4

UNITED NATIONS INDUSTRIAL DEVELOPMENT ORGANIZATION

VIENNA INTERNATIONAL CENTRE PO BOX 300, A-1400, VIENNA, AUSTRIA TELEPHONE: (+43 1) 26026-0 FAX: (+43 1) 26026-6815

Technical specifications the procurement of Workshop Equipment Project SAP No.: 101100 Rfx 700001532

Address of Bidder : ______Signature : ______

______Date : ______

______Email : ______

III. Notes for the invitees:

1. Offers to be made in US dollars. UNIDO reserves the right to accept all or part of your offer. 2. UNIDO will not accept partial offers. 3. Your bid must be accompanied by adequate technical documentation, catalogue(s) and other printed material or pertinent information (in English) for the items quoted. The equipment to be supplied should be worldwide known “Brand Name” products, unused and of the most recent or current models or stock lines, incorporating any recent improvements in design and components. All active (powered) equipment, unless stated otherwise, must operate on 220v +/- 20v, 50Hz +/- 2Hz with 3 pin UK plugs fitted as standard. Offers should specify warranty details (ideally 24 months warranty is required). 4. Delivery Period – No later than TWO weeks to EXW / DAP delivery point from the date of signing the purchase order. 5. Final point of delivery is The Swedish Academy for Training located in the Runaky Quarter - Erbil, IRAQ.

Page 8 of 4