11-300

10” Pro Cabinet

Operator’s Manual Record the serial number and date of purchase in your manual for future reference.

Serial Number: ______Date of purchase: ______For technical support or parts questions, email [email protected] or call toll free at (877)884-5167

11-300M1 www.rikontools.com TABLE OF CONTENTS

Specifications...... 2 Safety Instructions ...... 3 - 6 Getting To Know Your Cabinet Saw ...... 7 Contents of Package ...... 8 - 9 Installation ...... 10 Assembly ...... 10 - 15 Adjustments...... 16 - 21 Operation ...... 22 - 24 Maintenance ...... 25 Electricals & Wiring Diagram ...... 5 & 25 Troubleshooting ...... 26 Notes ...... 27 Parts Diagrams & Parts Lists ...... 28 - 37 Warranty ...... 38 Accessories ...... 39

SPECIFICATIONS

Motor ...... 3 HP, TEFC Motor Speed (no load)...... 3,450 RPM Volts ...... 240 V Amps, Hertz, Phase ...... 13 A, 60 Hz, 1Ph Blade Diameter...... 10” (254 mm) Blade Arbor...... 5/8” (16 mm) Blade Speed ...... 3,450 RPM Blade Tilt ...... Left Max Depth of Cut @ 90°...... 3-3/8” Max Depth of Cut @ 45°...... 2-1/4” Table Size (W x D) ...... 56-1/4” x 27” (1428.75 x 685.80 mm) Table Height ...... 35-1/4” (895.35 mm) Miter T-Slots (2) ...... 3/4” x 5/8” Height ...... 2-5/8” (66.68 mm) Max Rip Capacity (right of blade)...... 30” (762 mm) Dust Ports (1) ...... 4” Diameter (100 mm) Height ...... 41” (1,041.40 mm) Width ...... 64-1/4” (1,631.95 mm) Depth ...... 42” (1,066.80 mm) Net Weight ...... 425 lbs (193.78 kg)

NOTE: The specifications, photographs, drawings and information in this manual represent the current model when the manual was prepared. Changes and improvements may be made at any time, with no obligation on the part of Rikon Power , Inc. to modify previously delivered units. Reasonable care has been taken to ensure that the information in this manual is correct, to provide you with the guidelines for the proper safety, assembly and operation of this machine. 2 SAFETY INSTRUCTIONS

IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. There are certain applications for which this was designed. We strongly recommend that this tool not be modified and/or used for any other application other than that for which it was designed. If you have any questions about its application, do not use the tool until you have contacted us and we have advised you.

SAFETY SYMBOLS SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION. This symbol may be used in conjunction with other symbols or pictographs.

Indicates an imminently hazardous situation, which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation, which, if not avoided, could result in minor or moderate injury. NOTICE: Shown without Safety Alert Symbol indicates a situation that may result in property damage.

GENERAL SAFETY KNOW YOUR . Read the owner’s manual 4. AVOID A DANGEROUS WORKING ENVIRONMENT. carefully. Learn the tool’s applications, work capabilities, DO NOT use electrical tools in a damp environment or and its specific potential hazards. expose them to rain.

BEFORE USING YOUR MACHINE 5. DO NOT use electrical tools in the presence of flammable liquids or gasses. To avoid serious injury and damage to the tool, read and follow all of the Safety and Operating Instructions before 6. ALWAYS keep the work area clean, well lit, and operating the machine. organized. DO NOT work in an environment with floor surfaces that are slippery from debris, grease, and wax. 1. Some dust created by using power tools contains chemicals known to the State of California to cause cancer, 7. KEEP VISITORS AND CHILDREN AWAY. DO NOT birth defects, or other reproductive harm. permit people to be in the immediate work area, Some examples of these chemicals are: especially when the electrical tool is operating. • Lead from lead-based . • Crystalline silica from bricks, cement, and other 8. DO NOT FORCE THE TOOL to perform an operation • masonry products. for which it was not designed. It will do a safer and • Arsenic and chromium from chemically treated . higher quality job by only performing operations for Your risk from these exposures varies, depending on how which the tool was intended. often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area and work 9. WEAR PROPER CLOTHING. DO NOT wear loose with approved safety equipment, such as those dust masks clothing, gloves, neckties, or jewelry. These items can that are specially designed to filter out microscopic get caught in the machine during operations and pull the particles. operator into the moving parts. The user must wear a protective cover on their hair, if the hair is long, to 2. READ the entire Owner’s Manual. LEARN how to use prevent it from contacting any moving parts. the tool for its intended applications. 10. CHILDPROOF THE WORKSHOP AREA by 3. GROUND ALL TOOLS. If the tool is supplied with a 3 removing switch keys, unplugging tools from the prong plug, it must be plugged into a 3-contact electrical electrical receptacles, and using padlocks. receptacle. The 3rd prong is used to ground the tool and provide protection against accidental electric shock. DO 11. ALWAYS UNPLUG THE TOOL FROM THE NOT remove the 3rd prong. See Grounding Instructions ELECTRICAL RECEPTACLE when making adjust- on the following pages. ments, changing parts or performing any maintenance. 3 SAFETY INSTRUCTIONS

12. KEEP PROTECTIVE GUARDS IN PLACE AND IN 25. ALWAYS WEAR A DUST MASK TO PREVENT WORKING ORDER. INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including dust, crystalline silica dust 13. AVOID ACCIDENTAL STARTING. Make sure that and asbestos dust. Direct particles away from face and the power switch is in the “OFF” position before plugging body. Always operate tool in well ventilated area and in the power cord to the electrical receptacle. provide for proper dust removal. Use wherever possible. Exposure to the dust may 14. REMOVE ALL MAINTENANCE TOOLS from the cause serious and permanent respiratory or other injury, immediate area prior to turning “ON” the machine. including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged 15. USE ONLY RECOMMENDED ACCESSORIES. Use contact with dust. Allowing dust to get into your mouth of incorrect or improper accessories could cause serious or eyes, or lay on your skin may promote absorption of injury to the operator and cause damage to the tool. If in harmful material. Always use properly fitting NIOSH/OSHA doubt, check the instruction manual that comes with that approved respiratory protection appropriate for the dust particular accessory. exposure, and wash exposed areas with soap and water.

16. NEVER LEAVE A RUNNING TOOL UNATTENDED. 26. USE A PROPER EXTENSION CORD IN GOOD Turn the power switch to the “OFF” position. DO NOT CONDITION. When using an extension cord, be sure to leave the tool until it has come to a complete stop. use one heavy enough to carry the current your product will draw. The table on the following page shows the cor- 17. DO NOT STAND ON A TOOL. Serious injury could rect size to use depending on cord length and nameplate result if the tool tips over, or you accidentally contact the amperage rating. If in doubt, use the next heavier gauge. tool. The smaller the gauge number, the larger diameter of the extension cord. If in doubt of the proper size of an exten- 18. DO NOT store anything above or near the tool where sion cord, use a shorter and thicker cord. An undersized anyone might try to stand on the tool to reach it. cord will cause a drop in line voltage resulting in a loss of power and overheating. 19. MAINTAIN YOUR BALANCE. DO NOT extend USE ONLY A 3-WIRE EXTENSION CORD THAT HAS yourself over the tool. Wear oil resistant rubber soled A 3-PRONG GROUNDING PLUG AND A 3-POLE shoes. Keep floor clear of debris, grease, and wax. RECEPTACLE THAT ACCEPTS THE TOOL’S PLUG.

20. MAINTAIN TOOLS WITH CARE. Always keep tools 27. ADDITIONAL INFORMATION regarding the safe and clean and in good working order. Keep all blades and tool proper operation of this product is available from: bits sharp, dress grinding wheels and change other accessories when worn. • Power Tool Institute 1300 Summer Avenue 21. EACH AND EVERY TIME, CHECK FOR DAMAGED Cleveland, OH 44115-2851 PARTS PRIOR TO USING THE TOOL. Carefully check www.powertoolinstitute.org all guards to see that they operate properly, are not dam- aged, and perform their intended functions. Check for • National Safety Council alignment, binding or breaking of moving parts. A guard 1121 Spring Lake Drive or other part that is damaged should be immediately Itasca, IL 60143-3201 repaired or replaced. www.nsc.org

22. DO NOT OPERATE TOOL WHILE TIRED, OR • American National Standards Institute UNDER THE INFLUENCE OF DRUGS, MEDICATION 25 West 43rd Street, 4th Floor OR ALCOHOL. New York, NY 10036 www.ansi.org 23. SECURE ALL WORK. Use clamps or jigs to secure the work piece. This is safer than attempting to hold the • ANSI 01.1 Safety Requirements for work piece with your hands. Machines and the U.S. Department of Labor regulations 24. STAY ALERT, WATCH WHAT YOU ARE DOING, www.osha.gov AND USE COMMON SENSE WHEN OPERATING A POWER TOOL. 28. SAVE THESE INSTRUCTIONS. Refer to them A moment of inattention while operating power tools may frequently and use them to instruct others. result in serious personal injury. 4 SAFETY INSTRUCTIONS ELECTRICAL SAFETY EXTENSION CORDS

THIS TOOL IS PRE-WIRED FOR 240V THE USE OF AN EXTENSION CORD CIRCUITS, AND MUST BE GROUNDED WHILE IN USE TO WITH THIS MACHINE IS NOT RECOMMENDED. For PROTECT THE OPERATOR FROM ELECTRIC SHOCK. best power and safety, plug the machine directly into a dedicated, grounded electrical outlet that is within the IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, supplied cord length of the machine. grounding provides the path of least resistance for electric current and reduces the risk of electric shock. This tool If an extension cord needs to be used, it should only be is equipped with an electric cord that has an equipment for a limited operation of the machine. The extension grounding conductor and requires a grounding plug (not cord should be as short as possible in length, and have included). The plug MUST be plugged into a matching elec- a minimum gauge size of 14AWG. trical receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances. Check extension cords before each use. If damaged replace immediately. Never use a tool DO NOT MODIFY ANY PLUG. If it will not fit the electrical with a damaged cord, since touching the damaged area receptacle, have the proper electrical receptacle installed could cause electrical shock, and serious injury. by a qualified electrician. Use a proper extension cord. Only use cords listed by IMPROPER ELECTRICAL CONNECTION of the Underwriters Laboratories (UL). Other extension cords can equipment grounding conductor can result in risk of cause a drop in line voltage, resulting in a loss of power electric shock. The conductor with the green insulation and overheating of tool. When operating a power tool out- (with or without yellow stripes) is the equipment ground- doors, use an outdoor extension cord marked “W-A” or “W”. ing conductor. DO NOT connect the equipment grounding These cords are rated for outdoor use and reduce the risk conductor to a live terminal if repair or replacement of electric shock. of the electric cord or plug is necessary. Keep the extension cord clear of the working area. Position the cord so that it will not CHECK with a qualified electrician or service personnel if get caught on lumber, tools or other obstructions while you do not completely understand the grounding you are working with your power tool. instructions, or if you are not sure the tool is properly * Canadian electrical codes require extension cords to grounded when installing or replacing a plug. be certified SJT type or better. ** The use of an adapter in Canada is not acceptable. USE ONLY A 3-WIRE EXTENSION CORD THAT HAS THE PROPER TYPE OF A 3-PRONG GROUNDING PLUG THAT MATCHES THE MACHINE’S 3-PRONG PLUG AND ALSO THE 3-POLE RECEPTACLE THAT ACCEPTS THE TOOL’S PLUG. *

REPLACE A DAMAGED OR WORN CORD IMMEDIATELY. This tool is intended for use on a circuit that has a 240 volt electrical receptacle. FIGURE A shows the type of the 240V, 3-wire electrical plug and electrical receptacle that has a grounding conductor. See page 25 for the wiring diagram.

FIG. A Sample of 240 volt plug required for this machine. Consult a qualified electrician if the distance of the machine from the electrical panel is greater than 30 feet.

5 SAFETY INSTRUCTIONS

SPECIFIC SAFETY INSTRUCTIONS FOR TABLE This machine is intended for the cutting of natural and solid .The permissible workpiece dimensions must be observed (see Technical Specification). Any other use not as specified, including modification of the machine or use of parts not tested and approved by the equipment manufacturer, can cause unforeseen damage and invalidate the warranty. ATTENTION: Use of this still presents risks that cannot be eliminated by the manufacturer. Therefore, the user must be aware that wood working machines are dangerous if not used with care and all safety precautions are adhered to.

1. ALWAYS USE SAW BLADE GUARD, splitter and anti-kickback pawls for every through-sawing operation. Through-sawing operations are those in which the blade cuts completely through the workpiece when ripping or crosscutting. Always be sure blade guard is tightly secured. 2. ALWAYS HOLD WORK FIRMLY against the miter gauge or rip fence. 3. ALWAYS USE a push stick, especially when ripping narrow stock. 4. NEVER PERFORM ANY OPERATIONS FREEHAND, which means using only your hands to support or guide the workpiece. Always use either the fence or the miter gauge to position and guide the work. WARNING: FREEHAND CUTTING IS THE MAJOR CAUSE OF KICKBACK AND FINGER/HAND AMPUTATIONS. 5. NEVER STAND or have any part of your body in line with the path of the saw blade. Keep your hands out of the saw blade path. 6. NEVER REACH behind or over the cutting tool for any reason. 7. FEED WORK INTO THE BLADE against the direction of rotation only. 8. NEVER use the rip fence as a cut-off gauge when crosscutting. 9. NEVER ATTEMPT TO FREE A STALLED SAW BLADE without first turning the saw OFF. Turn power switch OFF immediately to prevent kickback and motor damage. 10. PROVIDE ADEQUATE SUPPORT to the rear and the sides of the table saw for long or wide workpieces. 11. AVOID KICKBACKS (work thrown back towards you) by keeping the blade sharp, the rip fence parallel to the saw blade and by keeping the splitter, anti-kickback pawls and guards in place, aligned and functioning. Do not release work before passing it completely beyond the saw blade. Do not rip work that is twisted, warped or does not have a straight edge to guide it along the fence. 12. AVOID AWKWARD OPERATIONS and hand positions where a sudden slip could cause your hand to move into the saw blade. 13. NEVER USE SOLVENTS to clean plastic parts. Solvents could possibly dissolve or otherwise damage the material. Only a soft damp cloth should be used to clean plastic parts. 14. NEVER CUT METALS or materials that make hazardous dust. 15. ALWAYS USE IN A WELL-VENTILATED AREA. Clean out from the interior of the saw to prevent a pontenial fire hazard. 16. NEVER LEAVE THE SAW RUNNING UNATTENDED. Do not leave the saw until blade comes to a complete stop. SAVE THESE INSTRUCTIONS. Refer to them often.

California Proposition 65 Warning WARNING: Some dust created by power sanding, sawing, grinding, , and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles. For more detailed information about California Proposition 65 log onto rikontools.com.

This owner’s manual is not a teaching aid. Use of this owner’s manual is intended to show assembly, adjustments, and general use. 6 GETTING TO KNOW YOUR CABINET SAW

E F G H

D I

J C B

A K L

A. Fence Bracket Hooks G. Rip Fence B. Blade Angle Handwheel H. Table Board C. ON / OFF Switch I. Rip Fence Locking Handle D. Rip Fence Rail J. Motor Cover E. Miter Gauge K. Scale F. Blade Guard Assembly with L. Blade Height Handwheel

7 CONTENTS OF PACKAGE Model 11-300 10” Pro Cabinet Saw body is shipped complete in one box. The fence assembly is shipped separately. Instructions for assembly and use of the fence are provided separate from this manual.

Unpacking, Checking Contents & Clean-up

1. Carefully remove all contents from the shipping carton. Compare the contents with the list of contents to make sure that all of the items are accounted for, before discarding any packing material. Place parts on a protected surface for easy identification and assembly. If any parts are missing or broken, please call RIKON Customer Service (877- 884-5167) as soon as possible for replacements. DO NOT turn your machine ON if any of these items are missing. You may cause injury to yourself or damage to the machine.

2. Report any shipping damage to your local distributor. Take photos for any insurance claims.

3. With the help of another person, carefully lift the saw from the packaging and place it on a level floor.

4. Clean all rust protected surfaces with ordinary house hold type grease or spot remover. Do not use; gasoline, thinner, mineral spirits, etc. These may damage painted surfaces.

5. Apply a coat of paste wax to the table to prevent rust. Wipe all parts thoroughly with a clean dry cloth. Be careful, as the blade has sharp teeth and may cause injury if touched.

6. Set packing material and shipping carton aside. Do not discard until the machine has been set up and is running properly.

TABLE OF LOOSE PARTS A. Main Saw Body B. Cast Iron Extenstion Wings (2) C. ON/OFF Switch Box and Wiring D. Blade Guard and Splitter Assembly E. Hand Wheels (2) Locking Knobs (2) F. Miter Gauge, Wrenches & Push Stick

A E

C

B

D F

CONTINUED ON PAGE 9

8 CONTENTS OF PACKAGE

TABLE OF LOOSE PARTS continued

Extension Wing Screw Package: A A. M8 Flat Washer (8) B B. M8 Lock Washer (8) C. 8mm x 50mm Hex Allen Bolt (8) C

Fence Bracket Package: D. M4 x 8mm Round HD Tap Screw (2) F G E. Wrench Hook (1) D F. Fence Storage Bracket (2) G. 1/4”-20 x 3/8” Round HD Tap Screw (4) E

Dust Port Hardware Package: H. Dust Port (1) I I. 1/4”-20 x 1/2” Round HD Tap Screw (4) H

Spacer Package: J. Spacer (for cast wing installation) (2) J

9 INSTALLATION MOVING & INSTALLING THE SAW

The table saw is heavy - over 400 3. Align the machine so that during use, the material lbs! It is best to assemble the machine near the being cut will not face aisles, doorways, or other work area where it will eventually reside. areas that bystanders may be in. Do not locate or use the machine in damp or wet conditions. 1. Carefully remove the machine from the shipping carton. See above instructions on handling the saw. 4. Once in place in your shop, level the machine with spacers, and secure it to the floor with lag screws 2. Position the machine on a solid, level foundation (not supplied) using the 4 holes in the cabinet base. that is located in an area that has ample space in front, right side and in back of the for cutting large or long material.

For best power and safety, the table saw should be plugged directly into a dedicated grounded electrical outlet that is within the supplied cord length of the machine. The use of an extension cord is not recommended. ASSEMBLY

• The table saw is a heavy machine; two people • DO NOT assemble the table saw until you are may be required for certain assembly sure the power switch is in the "OFF" position. operations. • For your own safety, DO NOT connect the • DO NOT assemble the table saw until you are machine to the power source until the machine sure the tool is unplugged. is completely assembled and you read and understand this entire User Manual.

MOBILE BASE TIP The use of mobile bases (not included) to increase portability are common for stationary table saws (A- Fig. 1). Consider starting your assembly with the mobile base of your choice; building the table saw within the base. This will make it easier to install the (Mobile Base not Included) mobile base now rather than lifting a fully assembled A table saw later.

NOTE: The mobile base must be rated to hold FIGURE 1 500 lbs!

1. Assemble the mobile base of your choice per the supplied instructions from the base manufacturer.

2. Lock the wheels and level the base.

3. With the help of another person, lift the saw body (Fig. 2) into the frame of the mobile base.

4. Begin assembly of the saw (Figures 3 thru 19). FIGURE 2 10 ASSEMBLY

THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE. A C HANDWHEEL ASSEMBLY 1. Place one of the handwheels (A-Fig. 3) onto the shaft to raise/lower the blade (B-Fig. 3) located on the front of the cabinet. Align the B in the back of the handwheel with the pin (C-Fig. 3). FIGURE 3 2. Thread the locking knob (A-Fig. 4) onto the threaded end of the shaft (C-Fig. 3).

3. Repeat the steps above to assemble the remaining handwheel and locking knob (A-Fig. 5) onto the blade angle shaft located on the left side of the cabinet. A

WRENCH AND FENCE HOOK ASSEMBLY FIGURE 4 1. Install both of the fence hooks (B-Fig. 5) to the left side of the cabinet using two M4 x 8mm tap screws for each hook. C 2. Attach the wrench hook (C-Fig. 5) to the left A side of cabinet using two M4 X 8mm round head tap screws.

DUST PORT INSTALLATION B 1. Locate the dust port and four 1/4”-20 x 1/2” FIGURE 5 Round HD Tap Screws from the package contents.

2. Place the dust port over the opening located at the bottom of the rear panel and attach using the four screws (A-Fig. 6) with a Phillips head screw driver.

A (x4)

FIGURE 6 11 ASSEMBLY EXTENSION WING INSTALLATION

The extension wings are heavy; two people are required for assembly. A 1.One person is required to lift an extension wing into position. The extension wing will sit into alignment pins to help locate the postion.

2. The second person will install two spacers (A-Fig. 7) into the table slot to ensure proper miter guage operation. FIGURE 7 3. Have the second person secure the extension wing in place using four 5/16”-18 x 45mm hex socket bolts, four M8 lock washers and four special wash- ers. Bolts and washers will install up from inside the cabinet into the bottom of the extension wing. Front Bolts SEE FIG. 8. Rear Bolts (x2) (x2) TABLE LEVELING ADJUSTMENT The pre-adjustment and setting of the extension wings for level and flatness have been performed at the factory. Follow the instructions below if further adustment is needed. FIGURE 8

1. Use a long and accurate straight edge to check table level and flatness. Place the straight edge onto the main table and check each wing separate- ly and then all three castings at once. This will ensure that the wings are level with the main table as well as each other. SEE FIG. 9.

2. Loosen the four small set screws (A-Fig. 10) on the side of the frame casting using a 2.5mm Allen wrench.

3. Next, loosen slightly the four 5/16”-18 x 45mm hex FIGURE 9 socket bolts (B-Fig. 10) previously used to attach extension wings to the saw body. THIN BOLTS 4. Adjust the four thin elevation bolts found between the top of the frame casting and the underside of A the extension wing using the 5/8” opening of the BLADE blade wrench. SEE FIG. 10. B WRENCH 5. Check progress periodically with the straight edge using steps described in the first step above.

6. Once the table level and flatness is achieved tighten the four 5/16”-18 x 45mm hex socket bolts and then the four small set screws on the side of FIGURE 10 the frame casting to retain the setting. 12 ASSEMBLY

THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE.

RIVING KNIFE/SPLITTER COMPONENTS A ASSEMBLY 1. Make sure blade or arbor is at the highest position before continuing to the steps below.

2. Remove the Table Insert (A-Fig. 11). The Table FIGURE 11 Insert is held to the table with four magnets. B 3. Loosen the lever (A-Fig. 12), and line up the Riving Knife/Splitter (B-Fig. 12) in the proper direction to the mounting bracket (C-Fig. 12). C A 4. Push the Riving Knife/Splitter all the way down into the mounting bracket, make sure the loca- tion pin is properly locked in the holes (B-Fig. 12) of the Riving Knife/Splitter.

FIGURE 12 5. Tighten the lever (A-Fig. 12).

REMOVING THE RIVING KNIFE/SPLITTER

1. Make sure blade or arbor is at the highest position before adding or removing the Riving 30” & 50” Fence Systems Knife/Splitter Assembly.

2. Reverse opertation in steps 2 thru 5 above in section “RIVING KNIFE/SPLITTER COMPONENTS ASSEMBLY”.

SWITCH INSTALLATION

NOTE: Please refer to the Rip Fence Operator’s Manual (cover shown right) provided in the Rip Fence carton for switch installation instructions.

(Shown on Model 11-200) RIP FENCE ASSEMBLY Operator’s Manual NOTE: Please refer to the Rip Fence Record the serial number and date of purchase in your manual for future reference. Operator’s Manual (cover shown right) Date of purchase: ______For technical support or parts questions, email [email protected] or call toll free at (877)884-5167 provided in the Rip Fence carton for V1 www.rikontools.com assembly and opertating instructions.

13 ASSEMBLY

THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE. E BLADE ASSEMBLY D B 1. Remove the hex nut (A-Fig. 13) and outer F flange (B-Fig. 13) from the blade arbor (C-Fig. A 13). C

The arbor has a right hand thread; to Note: FIGURE 13 loosen the hex nut turn it counterclockwise.

2. Place a 10” saw blade (D-Fig. 13) onto the A blade arbor (C-Fig. 13), make sure the teeth B of the blade are pointing down in the front of the table saw. Place the outer flange (B-Fig. 13) and hex nut (A-Fig. 13) onto the blade arbor and snug hex nut by hand. Place the open-end blade wrench (E-Fig. 13) on the flats of the inner blade flange (not shown) and the box-end blade wrench (F-Fig. 13) onto the hex nut and securely tighten. FIGURE 14

Note: The blade arbor has a right hand thread, to tighten the hex nut turn it clockwise.

3. Place a (A-Fig. 14) onto the saw blade and against the splitter assembly (B-Fig. 14). B Make sure the splitter is square to table

4. Lay a straight edge (A-Fig. 15) against the left side of the saw blade (B-Fig. 15) Align the split- A ter and make sure the splitter is aligned to the blade. FIGURE 15

14 ASSEMBLY

THE MACHINE MUST NOT BE C D PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE. CHANGING THE SPLITTER TO A RIVING KNIFE

Note: It is very important to keep the Riving Knife in close proximity to the blade to maintain an B even gap inside the kerf of the workpiece. A Keeping the gap open prevents the kerf of the FIGURE 16 workpiece to close behind the blade and causing kickback. B 1. Remove the guard assembly (A-Fig. 16) and kick-back pawl assembly (B-Fig. 16) by loosening knobs (C-Fig. 16) and (D-Fig. 16).

2. Remove the table insert, and loosen the Lever (A-Fig. 17) that locks the splitter into position. A

3. Slide the splitter to the desired height and make sure the location pins inside the bottom FIGURE 17 of the mounting bracket are properly inserted into the location holes (B-Fig. 17) of the split- ter. This will set the splitter to its lowest posi- tion. A B 4. Tighten the Lever (A-Fig. 17) and re-install the table insert.

CONNECTING SWITCH CORD TO MOTOR CORD

1. Place the switch cord (A-Fig. 18) through hole FIGURE 18 (B-Fig. 18) in front of cabinet. A B 2. Open motor cover, insert three prong male cord (A-Fig. 19) into three hole outlet of the female cord (B-Fig. 19).

3. Pull slack in switch cord into the cabinet. Make sure that the power cord inside of the cabinet is properly routed and clear of the saw blade and any pinch points for all blade height and blade angle settings. FIGURE 19 15 ADJUSTMENTS

RAISING AND LOWERING THE BLADE

The blade height adjustment handwheel and handwheel lock knob are located on the front of the cabinet above the blade angle scale. To raise the saw blade, loosen the handwheel lock knob (A-Fig. 20) (counterclockwise) and turn the hand- wheel (B-Fig. 20) clockwise. When the saw blade is at the desired height, tighten the handwheel A lock knob (clockwise) until it is securely tightened.

To lower the saw blade, loosen the handwheel lock knob (counterclockwise) and turn the hand- B wheel counterclockwise. When the saw blade is at the desired height, tighten the handwheel lock FIGURE 20 knob (clockwise) until it is securely tightened.

TILTING THE BLADE The blade angle handwheel and handwheel lock knob are located on the left side of the cabinet. To change the saw blade bevel angle, loosen the handwheel lock knob (A-Fig. 21) (counterclock- wise), then turn the hand wheel (B-Fig. 21) clock- wise.

When the saw blade is at its desired degree an- gle, tighten the handwheel lock knob (clockwise). B To return the saw blade bevel to zero degrees, loosen the handwheel lock knob (A-Fig. 21) (counterclockwise) then turn the handwheel A (B-Fig. 21) counterclockwise.

To tilt the blade angle to 45-degrees, loosen the handwheel lock knob (counterclockwise) and the FIGURE 21 adjustment knob and then turn the handwheel clockwise. When the saw blade is at 45-degrees it will come into contact with the adjustable posi- tive stop which will cause the blade to stop.

Tighten the hand-wheel lock knob (clockwise)and the adjustment knob until it is securely tightened.

16 ADJUSTMENTS

ADJUSTING BLADE ANGLE POSITIVE STOPS 1. Raise the saw blade (A-Fig. 22) to its highest position using the handwheel on the front of the saw. (See RAISING AND LOWERING THE BLADE on page sixteen)

2. Using an angle or (B-Fig. B A 22) check that the blade is 90 degrees to the saw table (zero degrees on blade angle scale).

3. If the blade is correctly set 90 degrees to the FIGURE 22 table no further adjustment is needed. If further adjustment is need continue to the next step.

4. Once the blade has been raised and set to 90 degrees (confirm this using your square), D tighten the bevel handwheel lock knob (A-Fig. 23) located on the side of the cabinet. This will A keep the blade from tilting further. C 5. If adjustment is necessary it will be done through the surface of the tabletop. The 90 FIGURE 23 degree stop adjustment is located within the left miter slot. The 45 degree stop is located next to the right miter slot.

6. If the blade is not set to 90 degrees when the set screw (A-Fig. 24) contacts the position stop, turn the set screw until the blade can be 90° Stop 45° Stop positioned to 90 degrees. A B 7. Loosen the blade angle handwheel lock and tilt the blade to 45 degrees. Using an angle or combination square (A-Fig. 25), make sure FIGURE 24 that the blade is set at 45 degrees.

8. With the blade tilted to 45 degrees, tighten the bevel handwheel lock knob to keep the blade from tilting further.

9. If the blade is not set to 45 degrees, when the set screw (B-Fig. 24) contacts the position A stop, turn the set screw until the blade can be positioned to 45 degrees. (See BLADE ANGLE SCALE ARROW ADJUSTMENT on page twenty for setting of the angle scale FIGURE 25 arrow position.) 17 ADJUSTMENTS CHECKING BLADE ALIGNMENT

The blade is set parallel at the factory and should not need any adjustments. You can check this by using a dial indicator (not included) or a combina- tion square (not included). It is recommended to A check the alignment before initial operation as follows:

THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE. B 1. Raise the saw blade (A-Fig. 26) to its highest C position using the handwheel on the front of the saw. (See RAISING AND LOWERING FIGURE 26 THE BLADE on page sixteen)

2. Place a combination square (B-Fig. 26) on the saw table with one edge of the square against the left miter slot (C-Fig. 26).

3. Adjust the square so the rule just touches the front position of the saw blade. Make sure the rule is not touching any of the carbide tips of A the saw blade.

4. Keep the rule in this position. B 5. Carefully rotate the saw blade back so that you take the measurement from the same spot on the saw blade.

6. Take a reading at the rear of the blade (A-Fig. 27) with the combination square. If there is a difference of more than. 01” between the rule FIGURE 27 and the blade, then an adjustment will have to be made to the table. See ADJUSTING BLADE ALIGNMENT on page nineteen.

18 ADJUSTMENTS ADJUSTING BLADE ALIGNMENT

NOTICE: Blade alignment is factory set and should not need adjustment. All saw blades have some runout. Therefore, readjusting the A (x6) blade alignment should only be attempted if it becomes necessary (see CHECKING BLADE ALIGNMENT on page eighteen).

THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE. B

1. To align the blade parallel to the miter slot, FIGURE 28 loosen six hex socket head screws (A-Fig. 28) under the front side of the table saw. This is the same side as the hand wheel (B-Fig. 28) that raises and lowers the blade.

2. Remove the three End Caps (A-Fig. 29) on the rear side of the table saw and loosen six hex

socket head screws. Three hex socket head (Position #1 hidden, see NOTE) screws (Positions 1, 5 & 6-Fig. 29) are outside the cabinet, three are located behind the End Caps (Positions 2, 3, & 4-Fig. 29) inside the 3 4 cabinet. NOTE: Open the Motor Cover to gain 2 1 5 6 access to Position #1. A (x3)

3. The saw table is now loose and can be reposi- tioned until the blade is parallel to the miter slot. Repeat steps in CHECKING BLADE ALIGNMENT on page eighteen.

FIGURE 29 4. When blade is parallel to miter slot, tighten all twelve hex socket head screws.

5. Recheck blade alignment.

6. Tilt the blade to 45 degrees, and rotate the saw blade by hand. Make sure the blade does not contact the table insert.

19 ADJUSTMENTS BLADE ANGLE SCALE ARROW ADJUSTMENT 1. Make certain that the blade is set 90 degrees to the table surface with a combination square. See page 17, figure 22ADJUSTING BLADE ANGLE POSITIVE STOPS. A

2. Check that the bevel arrow is pointing to the zero degree mark on the bevel scale located on the front of the cabinet.

3. To adjust arrow, loosen the Phillips head screw (A-Fig. 30), reposition the bevel arrow and tighten screw. (Handwheel has been removed for clarity; do not need to remove to make adjustment.) FIGURE 30

TABLE INSERT ADJUSTMENT

THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE.

1. The table insert (A-Fig. 31) must always be level with the saw table.

2. Place a straight edge (not provided) across the front and rear of the table insert. Check that the insert is perfectly level with the saw table. B B A 3. To level the table insert, turn one or more of C the four corner adjusting set screws (B-Fig. 31) as needed and recheck.

4. The table insert is equipped with a finger hole (C-Fig. 31) for easy removal. FIGURE 31

20 ADJUSTMENTS MITER GAUGE ADJUSTMENT

1. The miter gauge has adjustable positive stops B at 0-degree and 45-degrees or it can be manu- ally set at any angle between 60-degrees. A C 2. To rotate the miter gauge body (A-Fig. 32), loosen knob (B-Fig. 32) and pull out plunger (C-Fig. 32) and rotate miter gauge body to desired angle and tighten knob.

3. To rotate to the next positive stop, pull plunger (C-Fig. 32) out, rotate miter gauge body then push plunger back in and continue rotating miter gauge body until it stops against the next positive stop. FIGURE 32

ADJUSTING POSITIVE STOPS B 1. To adjust the three positive stops, loosen the knob (B-Fig. 32), pull out on plunger (C-Fig. A 32) and turn the miter gauge over.

2. Loosen the lock nut (A-Fig. 33) 3 or 4 turns.

3. Place a square against the guide bar and front of the miter gauge body. Square the miter gauge body to the guide bar and tighten knob.

4. Push in the plunger and make adjustments to the stop screw (B-Fig. 33) so that it touches FIGURE 33 the plunger and tighten the lock nut.

5. Recheck the positive stop angle to the saw blade. Insert the guide bar into the miter slot and slide the miter gauge up to the saw blade. A (x4) NOTICE: If the miter bar feels loose in the slot adjust the four hex set screws in the side of the miter bar (A-Fig. 34) to add side tension to slot.

6. To check, place a square against the saw blade and miter gauge body. If any more adjustments are needed repeat steps above.

FIGURE 34 7. To set both 45-degree positive stops, repeat steps 1 thru 6 above at each 45-degree set- ting. 21 OPERATION

A separate electrical circuit should be used for this table saw. The circuit should not be less than A #14AWG wire and should be protected with a 15- amp breaker. Have a qualified electrician repair or replace damaged or worn cord immediately.

Before connecting the motor to the power source, make certain the switch is in the “OFF” position and be sure that the electric current is of the B same rating as the motor nameplate. All line con- nections should make good contact. Running on low voltage or long, under rated extension cords will damage the motor. FIGURE 35

DO NOT expose the table saw to rain or oper- ate the in damp locations. MAKE SURE all parts have been assembled correctly and are in work- A ing order. KEEP table surface clear of tools and debris before starting table saw.

STARTING AND STOPPING THE SAW

1. The ON/OFF switch is located under the front rail on the table saw.

2 To turn the table saw on, press the green ON button (A-Fig. 35) in about one half inch until FIGURE 36 you feel or hear a “click”.

3. To turn the table saw off, press the large red “OFF” paddle (B-Fig. 35).

4. If the power is interrupted, or the saw will not start, the breaker may have tripped. Press the A “OFF” button and locate the breaker on the side of the switch box (A-Fig. 36). Depress the breaker button and Press the “ON” button to test operation.

5. Using a padlock (not provided), it is possible to lock the switch to prevent unauthorized use. FIGURE 37 Lift the red “OFF” paddle and place a padlock through the holes (A-Fig. 37) in the side of the “ON” button and then lock the padlock. 22 OPERATION

TYPES OF SAWING OPERATIONS CROSSCUTTING WARNING: Use caution when starting the cut to WARNING: For your own safety, always observe the prevent binding of the guard against the workpiece. following safety precautions. This cut is performed with the miter gauge set at “0”, • Never make any cut freehand (without using miter and is used for cutting across the workpiece grain at gauge or rip fence). Blade can bind in the cut and 90° (blade square with both the edge and flat side of cause a kick back. wood). • Always lock miter gauge or rip fence securely when MITER CUTTING in use. • Remove rip fence from the table when miter gauge WARNING: Miter angles greater than 45° may force is in use. the blade guard assembly into the saw blade causing • Remove miter gauge from table when rip fence is in damage to the blade guard assembly and personal use. injury. Before starting the motor, test the operation by • Make sure blade guard is installed for all “through feeding the workpiece into the blade guard assembly. sawing” operations. Through sawing operations are If the blade guard assembly contacts the blade, place those operations in which the saw blade cuts com- the workpiece under the blade guard assembly, not pletely through the thickness of the wood. Replace touching the blade, before starting the motor. guard immediately after completion of resawing, rab- WARNING: Certain workpiece shapes, such as mold- beting and dadoing. ing may not lift the blade guard assembly properly. Frequently check action of anti-kickback pawls by With the power off, feed the workpiece slowly into the passing the workpiece alongside the spreader while blade guard area and until the workpiece touches the saw is off. Pull the workpiece toward you. If the pawls blade. If the blade guard assembly contacts the blade, do not dig into the workpiece and hold it, the pawls place the workpiece under the blade guard assembly, must be sharpened. not touching the blade, before starting the motor. This cut is performed with the miter gauge, and is used • Have blade extend approximately 1/8″ above top of for cutting at an angle other than 90° square with the workpiece. Additional blade exposure increases edge of the workpiece. hazard potential. • Do not stand directly in front of blade in case of a BEVEL CROSSCUTTING kickback. Stand to either side of the blade. WARNING: When possible, use the right miter gauge • Keep your hands clear of the blade and out of the slot when bevel crosscutting so that the blade tilts path of the blade. away from the miter gauge and your hands. • If the blade stalls or stops while cutting, turn switch OFF and safety disconnect OFF before attempting to WARNING: Use caution when starting the cut to pre- free the blade. vent binding of the guard against the workpiece. • Do not reach over or behind the blade to pull the This cut is performed with the miter gauge, and is the workpiece through the cut, to support long or heavy same as crosscutting, except that the workpiece is workpieces, to remove small cut-off pieces of mate- also cut at an angle other than 90° square to the flat rial or for any other reason. side of the wood (blade is at an angle).

• Do not pick up small pieces of cut-off material from COMPOUND MITER CUTTING the table. Remove them by pushing them off table This cut is performed with the miter gauge, and is a with a long stick. Otherwise they could be thrown combination of miter cutting and bevel crosscutting. back at you by the rear of the blade. The cut is made at an angle other than 90° to both the • Do not remove small pieces of cut-off material that edge and flat side of wood. may become trapped inside blade guard while saw is on. This could endanger your hands or cause a kick back. Turn saw off. After blade has stopped turning, lift guard and remove the piece. • Always lower blade below the table level when machine is not in use. 23 OPERATION RIPPING DADOING WARNING: When bevel ripping and whenever possible, This cut is performed with either the miter gauge or rip place the fence on the side of the blade so that the blade fence. Dadoing is done with a set of blades ( set) is tilted away from the fence and hands. Keep hands rather than standard saw blades. The is used clear of the blade and use a push stick to feed the work- to groove wood similar to ploughing and rabbeting. How- piece if there is less than 6″ between the fence and the ever, the dado set allows operator to remove more mate- blade. rial in one pass. The operator, with a dado set, can vary width of cut up to 3⁄4″. This cut is performed with the rip fence, and is used to cut the workpiece lengthwise with the grain. Position the Instructions for operating dado set are contained in own- fence to the desired width of rip and lock in place. When er’s manual furnished with dado set. Dadoing requires ripping long boards or large panels, always use a work cuts which do not go all the way through material. There- support. fore, the blade guard and splitter must be removed. Dado sets have different characteristics than saw blades. BEVEL RIPPING When using a dado set, a dado table insert (not includ- Before connecting the table saw to the pow- WARNING: ed) must be used. er source or operating the saw, always inspect the blade guard assembly and riving knife for proper alignment and IMPORTANT: Always use correct insert. When using the clearance with saw blade. Check alignment after each dado set, use caution. Use featherboards and push change of bevel angle. sticks as applicable. WARNING: When possible, place the fence on the right WARNING: Always immediately replace the standard side of the blade so that the blade is tilted away from the blade, blade guard and blade insert when you are fence and hands. Keep your hands clear of the blade finished dadoing. and use a pushstick to feed the workpiece if there is less than 6″ between the fence and the blade. FREEHAND Freehand is a very dangerous operation of This cut is performed with the rip fence, and is the same WARNING: making a cut without using the miter gauge or rip fence. as ripping, except that the blade is set at an angle other Freehand cuts on a Table than 90°. must never be performed Saw. RESAWING CUTTING OVERSIZED WORKPIECES This cut is performed with the rip fence, and is used to When cutting long workpieces or large panels, always rip a workpiece through its thickness rather than across support workpiece that is not on table. Use adjustable its flat width. Do not attempt to resaw bowed or warped roller stand or make simple support by clamping a piece material. of to saw horse. Add facings to miter gauge or NOTE: It may be necessary to remove blade guard and rip fence as needed. use work supports as well as push blocks when perform- Do not allow facings to interfere with the ing this operation. IMPORTANT: operation of blade guard. WARNING: Install blade guard immediately upon com- pletion of resawing operation. BLADE SELECTION Blade selection is based on type of material being cut PLOUGHING and how it will be cut. There are three general types of This cut is performed with the rip fence, and is used to saw blades: blades cut with grain of wood, make a groove lengthwise with the grain of the work- cut-off saw blades cut across grain, and combination piece. Use proper hold downs and feed devices. saw blades cut with grain, across grain and any angle to grain. RABBETING IMPORTANT: Your saw is only as accurate and efficient This cut is performed with either the miter gauge or rip as the blade or cutting tool used. fence. Rabbeting is used to cut out a section of the cor- ner of a workpiece, across an end or along an edge. To make a requires cuts which do not go all the way through the material. Therefore, blade guard must be re- moved. Rabbet cuts can also be made using dado head. 24 MAINTENANCE

BEFORE CLEANING OR CARRYING OUT MAINTENANCE WORK, DISCONNECT THE MACHINE FROM THE POWER SOURCE (WALL SOCKET). NEVER USE WATER OR OTHER LIQUIDS TO CLEAN THE MACHINE. USE A BENCH BRUSH. DO NOT USE COMPRESSED AIR NEAR BEARINGS. REGULAR MAINTENANCE OF THE MACHINE WILL PREVENT UNNECESSARY PROBLEMS.

1. Keep the inside of the cabinet clear of saw dust and wood chips. With the table saw unplugged, vacuum out the inside of the cabinet or blow out the inside with an air hose. Be sure to use air pressure no higher than 50 P.S.I. as high pressure air may damage sealed bearings. If blowing sawdust, wear a proper dust mask and eye protection to prevent debris from being inhaled and blowing into your eyes. 2. The table saw has sealed lubricated bearings in the motor housing that do not require any additional lubrication from the operator. 3. Use a wire brush to clean off the worm gears and trunnions and apply a white lithium grease to keep them lubricated. 4. To prevent rust apply a heavy coat of WD-40 to unpainted cast iron surfaces. 5. Before each use: Check the power cord and plug for any wear or damage. Check for any loose screws, hardware, locking handles, jigs or various lathe accessories. Check the area to make sure it is clear of any misplaced tools, lumber, cleaning supplies, etc. that could hamper the safe operation of the machine.

WIRING DIAGRAM

This machine must be grounded. Replacement of the power supply cable should only be done by a qualified electrician. See page 5 for additional electrical information.

As received from the factory, your bandsaw is ready to run at 240V operation.

25 TROUBLESHOOTING

FOR YOUR OWN SAFETY, ALWAYS TURN OFF AND UNPLUG THE MACHINE BEFORE CARRYING OUT ANY TROUBLESHOOTING.

For parts or technical questions contact: [email protected] or 877-884-5167.

26 NOTES Use this section to record maintenance, service and any calls to Technical Support:

27 PARTS DIAGRAM

SAFETY GUARD, SPLITTER & RIVING KNIFE

28 PARTS LIST

SAFETY GUARD, SPLITTER & RIVING KNIFE P11-300-1 P11-300-2 P11-300-3 P11-300-4 P11-300-5 P11-300-6 P11-300-6A P11-300-7 P11-300-8 P11-300-9 P11-300-10 P11-300-11 P11-300-13 P11-300-14 P11-300-15 P11-300-16 P11-300-17 P11-300-18 P11-300-19 P11-300-20 P11-300-21 P11-300-22 P11-300-23 P11-300-24 P11-300-25 P11-300-26 P11-300-27 P11-300-28 P11-300-29 P11-300-29A P11-300-29C P11-300-29D P11-300-29E P11-300-29F PART NO. PART the Serial Number of your machine is required. RIGHT BLADE GUARD RIGHT SHOULDERD SCREW ROUND PIN M4X10mm ROUND HEAD CUTTING SCREW SCREW M4X6mm HEX SOC SET ARM BLADE GUARD SUPPORT LABEL WARNING SCREW M5x12mm HEX SOC SET FIXED SHAFT BALL 7/32 STEEL SPRING BUSHING GRIP TWIST BLADE GUARD LEFT M4x8mm COUNTERSUNK HEAD SCREW RIVING KNIFE RING M12 RETAINING ANTI KICKBACK FINGER RIGHT SPRING TWIST M3x30mm SPRING PIN ANTI KICKBACK FINGER LEFT ANTI KICKBACK FINGER SUPPORT BOLT SPECIAL SPRING BASE NUT FAST RIVING KNIFE PLATE RIVING KNIFE SUPPORT M6x12mm HEX SOC HEAD SCREW M6 LOCK WASHER SCREW M6x8mm HEX SOC SET M8 BLOCKING NUT(LEFT) SCREW M5x10mm HEX SOC SET SCR TAP ST2.9X6.5mm CROSS COUNTERSUNK BEARER ANTI KICKBACK FINGER SUPPORT DESCRIPTION NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts. For Parts under Warranty, 1 2 3 4 5 6 6A 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 29A 29C 29D 29E 29F KEY NO. KEY

29 PARTS DIAGRAM

MAIN TABLE & EXTENSION WINGS

SWITCH & CORD ASSEMBLY

30 PARTS LIST

MAIN TABLE & EXTENSION WINGS KEY NO. DESCRIPTION PART NO. 30 1/4-28 X 3/8” NYLON SET SCREW P11-300-30 31 TABLE INSERT P11-300-31 31A TABLE INSERT PAD P11-300-31A 32 M8X6mm MAGNET P11-300-32 33 TABLE P11-300-33 35 M8X12mm HEX SOC SET SCREW P11-300-35 35A M8X40mm HEX SOC SET SCREW P11-300-35A 36 SPECIAL WASHER (8.3X25X3.5) P11-300-36 37 M8 LOCK WASHER P11-300-37 38 5/16-18 X42mm HEX SOC HEAD SCREW P11-300-38 39 LEFT EXTENSION WING P11-300-39 40 SPECIAL WASHER (8.5X20X2) P11-300-40 41 M8 LOCK WASHER P11-300-41 42 5/16-18X28mm HEX SOC HEAD SCREW P11-300-42 45 MICRO ADJUST FLAT WASHER P11-300-45 46 RIGHT EXTENSION WING P11-300-46 SWITCH & CORD ASSEMBLY KEY NO. DESCRIPTION PART NO. 60 SWITCH PADDLE P11-300-60 61 M4X25mm ROUND HEAD TAP SCREW P11-300-61 62 SWITCH P11-300-62 63 SWITCH BOX P11-300-63 63A SWITCH RESET LABEL P11-300-63A 64 M4X16mm ROUND HEAD TAP SCREW P11-300-64 66 SWITCH SUPPORT P11-300-66 68 M5 HEX NUT P11-300-68 69 M5 EXT TOOTH WASHER P11-300-69 70 M5X12mm PAN HEAD SCREW P11-300-70 73 RESET SWITH(25Amp,125/250V) P11-300-73 74 JUMPER WIRE (BLACK) P11-300-74 75 SWITCH CORD P11-300-75 75A STRAIN RELIEF(7P-2) P11-300-75A 76 POWER CORD P11-300-76

NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required. 31 PARTS DIAGRAM

MITER GAUGE

32 PARTS LIST

MITER GAUGE

KEY NO. DESCRIPTION PART NO. 114 MITER GAUGE BODY P11-300-114 115 SPECIAL WASHER P11-300-115 116 SPECIAL SCREW P11-300-116 119 GUIDE BAR P11-300-119 120 M4 X 16mm SET SCREW P11-300-120 121 1/4”x3/4 PIN P11-300-121 122 M4X10mm PAN HEAD SCREW P11-300-122 122A M4 FLAT WASHER P11-300-122A 123 PLUNGER P11-300-123 124 PLUNGER BLOCK P11-300-124 125 CURSOR P11-300-125 126 M4X15mm PAN HEAD SCREW P11-300-126 127 M4X20mm PAN HEAD SCREW P11-300-127 127A M4 HEX NUT P11-300-127A 130 MITER SCALE P11-300-130 131 SPECIAL WASHER (8.3X25X3.5) P11-300-131 132 MITER GAUGE KNOB P11-300-132

NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required.

33 PARTS DIAGRAM MOTOR & TRUNNION

34 PARTS LIST MOTOR & TRUNNION P11-300-244 P11-300-245 P11-300-246 P11-300-247 P11-300-247A P11-300-247B P11-300-248 P11-300-249 P11-300-250 P11-300-251 P11-300-251A P11-300-2252 P11-300-253 P11-300-254 P11-300-255 P11-300-256 P11-300-256A P11-300-258 P11-300-259 P11-300-260 P11-300-261 P11-300-261A P11-300-262 P11-300-262A P11-300-263 P11-300-264 P11-300-265 P11-300-266 P11-300-266A P11-300-266B P11-300-266C P11-300-267 P11-300-268 P11-300-268A P11-300-269 P11-300-270 P11-300-274 P11-300-275 P11-300-276 P11-300-277 P11-300-280 P11-300-281 P11-300-282 P11-300-283 P11-300-284 P11-300-285 P11-300-286 P11-300-287 P11-300-288 PART NO. PART M4 x 22mm SPRING PIN NUT SPECIAL TRUNNION FRONT M6 x 20mm HEX SOC HEAD SCREW M6 LOCK WASHER WASHER M6 FLAT M8X30mm SPRING PIN M6X20mm HEX SOC HEAD SCREW TRUNNION MAIN RAISE/LOWER SLEEVE SLEEVE SPECIAL RAISE/LOWER SPACER POINTER WASHER M6 FLAT M6X16mm CHEESE HEAD SCREW HANDWHEEL ASSY HANDLE LOCK KNOB HANDWHEEL WORM GEAR M4x20mm SPRING PIN SHAFT TILT M4x22mm SPRING PIN ECCENTRIC SCREW SLEEVE BRACKET FRONT WASHER M10 FLAT M10X45mm HEX HEAD SCREW COLLAR TILT (t=2mm) 3/8” FIBER WASHER COLLAR SCREW 1/4-20 X 1/4” HEX SOC SET SCREW M6X8mm HEX SOC SET M5 HEX NUT (5.4X18X3) WASHER M5 FLAT BRACKET TILT M5X25mm ROUND HEAD SCREW 9/16-18 JAM HEX NUT WASHER M10 FLAT M10 LOCK WASHER M10 HEX NUT WRENCH (7/8” x 1/2”) 22mm OPEN END WRENCH ALLEN WRENH 2.5mm ALLEN WRENCH 3mm ALLEN WRENCH 4mm ALLEN WRENCH 5mm ALLEN WRENCH 6mm 1/8”ALLEN WRENCH SPACER DESCRIPTION 244 245 246 247 247A 247B 248 249 250 251 251A 252 253 254 255 256 256A 258 259 260 261 261A 262 262A 263 264 265 266 266A 266B 266C 267 268 268A 269 270 274 275 276 277 280 281 282 283 284 285 286 287 288 KEY NO. KEY P11-300-200 P11-300-201 P11-300-202 P11-300-203 P11-300-203A P11-300-204 P11-300-205 P11-300-205A P11-300-205B P11-300-205C P11-300-206 P11-300-207 P11-300-208 P11-300-209 P11-300-210 P11-300-211 P11-300-212 P11-300-213 P11-300-214 P11-300-215 P11-300-216 P11-300-217 P11-300-218 P11-300-220A P11-300-221 P11-300-222A P11-300-223 P11-300-224A P11-300-225A P11-300-226 P11-300-227 P11-300-228 P11-300-229 P11-300-230 P11-300-231 P11-300-232 P11-300-238 P11-300-239 P11-300-240 P11-300-240A P11-300-240B P11-300-240C P11-300-240D P11-300-241 P11-300-241A P11-300-241B P11-300-242 P11-300-424A P11-300-242B P11-300-243 PART NO. PART 5/8-18 +C107:C148JAM NUT ARBOR PULLEY 5x5x15 KEY HEAD SCREW M5X12mm PAN ARBOR SPACER BEARING 6004-2RS BALL BRACKET ARBOR RAISING SUPPORT GIB M5X25mm HEX HEAD SCREW M5 HEX NUT ARBOR SLEEVE 6004 WASHER WAVE BEARING 6004-2RS BALL ARBOR SHAFT BLADE (OD: 10” , ID: 5/8”,TEETH: 40) BLADE FLANGE ARBOR NUT M10 x 45mm HEX HEAD SCREW WASHER M10 FLAT REAR BRAKET WASHER M10 FLAT M10 LOCK WASHER M10 HEX NUT (29.5 x 6Rib K) BELT SCREW 1/4-20×3/8 HEX SOC SET PULLEY MOTOR 5 x 36mm KEY (3HP) ASSEMBLY MOTOR (3HP)11-300 SPEC LABEL MOTOR M8X20mm HEX SOC HEAD SCREW M8 LOCK WASHER WASHER M8 FLAT BRACKET SUPPORT MOTOR WASHER M10 FLAT M10 LOCK WASHER M10X25mm HEX HEAD SCREW PIN ELEVATION SCREW M6X8mm HEX SOC SET BRACKET ELEVATING WASHER WAVE WASHER FLAT SPECIAL BOLT PIVOT ELEVATING M6X10mm HEX SOC HEAD SCREW M8X30mm HEX SOC HEAD SCREW M8 LOCK WASHER WASHER M8 FLAT ASSEMBLY SHAFT ELEVATING M4 x20mm SPRING PIN WORM GEAR SHAFT ELEVATING DESCRIPTION 200 201 202 203 203A 204 205 205A 205B 205C 206 207 208 209 210 211 212 213 214 215 216 217 218 220A 221 222A 223 224A 225A 226 227 228 229 230 231 232 238 239 240 240A 240B 240C 240D 241 241A 241B 242 242A 242B 243 KEY NO. KEY 35 PARTS DIAGRAM SAW CABINET

36 PARTS LIST SAW CABINET P11-300-311 P11-300-316 P11-300-317 P11-300-318 P11-300-319 P11-300-320 P11-300-321 P11-300-322 P11-300-324 P11-300-325 P11-300-327 P11-300-328 P11-300-329 P11-300-329B P11-300-329C P11-300-424 P11-300-425 P11-300-426 P11-300-450 PART NO. PART DUST CHUTE DUST 1/4-20 x3/8 ROUND HEAD TAP SCREW TAP 1/4-20 x3/8 ROUND HEAD CABLE SCREW TAP 1/4-20 x3/8 ROUND HEAD PORT DUST SCREW TAP 1/4-20 x1/2 ROUND HEAD SCREW M5X6mm HEX SOC SET END CAP SCREW TAP 1/4-20 x3/8 ROUND HEAD INSULATOR NAMEPLATE WRENCH HOOK FENCE BRACKET SCREW TAP M4X8 ROUND HEAD WASHER M4 FLAT SCREW TAP 1/4-20 x3/8 ROUND HEAD M8X20mm HEX HEAD SCREW M8X40mm HEX HEAD SCREW M8 HEX NUT PUSH STICK DESCRIPTION 311 316 317 318 319 320 321 322 323 324 325 327 328 329 329B 329C 424 425 426 450 KEY NO. KEY P11-300-301 P11-300-300A P11-300-301B P11-300-301E P11-300-301F P11-300-302 P11-300-303 P11-300-304 P11-300-304A P11-300-304B P11-300-304C P11-300-305 P11-300-305A P11-300-305B P11-300-305C P11-300-306 P11-300-307 P11-300-308 P11-300-309 P11-300-310 PART NO. PART the Serial Number of your machine is required. NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts. For Parts under Warranty, CABINET CABINET (11-300) SPEC LABEL SCALE BEVEL ACCESS DOOR CABINET M4X8mm ROUND HEAD TAP SCREW TAP M4X8mm ROUND HEAD ASSY HINGE SCREW TAP 1/4-20 x3/8 ROUND HEAD COVER MOTOR LABEL BIG WARNING LABEL WARNING SMALL SPONGE 5/16-24 HEX NUT WASHER M8 FLAT SPRING 5/16-24X2.36“ HEX HEAD SCREW KNOB SIDE PANEL CABINET SCREW TAP 1/4-20 x3/8 ROUND HEAD SCREW TAP 1/4-20 x3/8 ROUND HEAD SCREW ADJUSTABLE DESCRIPTION 301 301A 301B 301E 301F 302 303 304 304A 304B 304C 305 305A 305B 305C 306 307 308 309 310 KEY NO. KEY 37 WARRANTY

38 ACCESSORIESNOTES

13-299 DADO BLADE TABLE INSERT Quality cast aluminum construction with 1-1/8” x 7-5/8” blade opening. Includes four leveling screws.

C10-100 PUSH STICK Keep your hands clear of the blade with this rigid plastic push stick. Ergonomic design helps you push material through a saw, or other cutting devices giving you better control of the workpiece while providing safety.

ADDITIONAL TABLE SAW ACCESSORIES For additional table saw accessories or replacement parts, contact your local RIKON distributor, or visit the RIKON website at www.rikontools.com.

39 11-300

For more information: 16 Progress Road Billerica, MA 01821

877-884-5167 / 978-528-5380 [email protected]

11-300M1 www.rikontools.com