DOCSLIB.ORG

PRS4000/PRS1025 60 Ghz Wigig Chipset

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
PRS4000/PRS1025 60 Ghz Wigig Chipset PRS4000/PRS1025 60 GHz WiGig Chipset Product Brief 2015‐03‐01 Overview The PRS4000 and PRS1025 comprise a highly integrated 60 GHz chipset compliant with the IEEE 802.11ad specifications. The two integrated circuits implement a complete SuperSpeed USB 3.0 to WiGig solution. The PRS4000 Low Power WiGig Baseband incorporates the Analog Front End, BB PHY/MAC, and two RISC CPU cores. The PRS1025 is a single chip RF IC incorporating an integrated antenna of 8.5 dBi peak gain. The chipset is ideal for wireless display, wireless docking, and multi‐gigabit mobile wireless applications. Features PRS4000 Low Power Baseband PRS1025 High Performance WiGig Radio IEEE 802.11ad compliant Tx output power: Up to +22.5 dBm EIRP Fully integrated AFE, PHY and MAC Better than ‐21 dB transmit EVM (16‐QAM) Highly flexible, dual CPU soft MAC integrates WiGig Receiver noise figure: < 5 dB MAC functions Receiver conversion gain > 70 dB PHY supports MCS0 to MCS12 (4.62 Gb/s) Integrated 8.5dBi Tx and Rx antennas 2 Gb/s link at 10m (MCS8) PLL tunes to all channels of IEEE 802.11ad 1 Gb/s at 20m (MCS4) specifications using integrated XO 0.8 mm thick, 7mm × 7mm BGA 0.7 mm thick, 7mm × 7mm BGA Package Application Diagram Status LED Serial Flash 2.5V 1.8V CPF 1.2V PWM SPI PRS4000 REFCLK PRS1025 3.3V (USB) Tx Antenna Bias 2.5V (IO) Peripherals MAC PHY AFE 1.1V (Core) SPI, I2C, PWM, UART, GPIO, LSADC, Upper MAC Memory DAC TX_I XREF1 JTAG (640K) WiGig PHY Tx Path Tx Data Path PLL USB 3.0 Upper MAC CPU DAC TX_Q XREF2 45 MHz USB 3 USB 3.0 Packet Buffer MAC/PHY IF PHY and Device/ PLL Digital AGC VCO XO Host Shared Memory GCMP (AES) (416K) USB 2 Encryption USB 2.0 PHY ADC RX_Q Lower MAC CPU Configuration WiGig PHY Rx Data Path and GPIO Lower MAC Memory Rx Path Control ADC RX_I GPIO (optional), SPI 192K SPI Radio Control Rx Antenna SPI Revision 0.15.03 © 2015 Peraso Technologies. All Rights Reserved. Page | 1 PRS4000/PRS1025 60 GHz WiGig Chipset Product Brief General Description The PRS4000 WiGig baseband and PRS1025 WiGig radio are compliant with the single carrier modulation and coding schemes of the IEEE 802.11ad specifications (MSC0 to MSC12). This chipset implements a low cost, low power, high performance SuperSpeed USB 3.0 to WiGig device. The PRS4000 includes a USB 2.0 and 3.0 device/host system interface. Supporting link speeds of up to 2.0 Gb/s, it is possible to configure the PRS4000 as a multi‐gigabit WiGig USB adaptor or as the 60 GHz wireless connection for a WSB peripheral device. The PRS4000 MAC incorporates two powerful RISC processors to provide the highest flexibility in supporting 801.11ad MAC functionality. CPU code boot loading is supported from the USB interface or external serial flash. Security is ensured through the use of AES with a 128‐bit key and a 128‐bit block size utilizing GCM for data confidentiality and GMAC for authentication and integrity. RSNA and 802.1X are used to provide a robust authentication and association procedure. The MAC includes sufficient internal memory to buffer data transfers to and from the PHY as well as receiving/transmitting packets to the host interfaces. No additional RAM is required. The PRS4000 PHY is capable of modulating/demodulating all control and single carrier π/2‐BPSK, π/2‐ QPSK and 16‐QAM WiGig coding schemes (MCS0 to MCS12) up to a maximum rate of 4.62 Gb/s. LDPC forward error correction maximizes performance in unreliable or noisy communication channels. The PRS4000 also includes a highly configurable programmable IO subsystem consisting of GPIO, UART, SPI, TWI, PWM and JTAG. The firmware incorporates multiple layers of debug functionality such logging and extensive statistic and event counters. The PRS4000 supports seamless connection to all Peraso 60 GHz radios: The PRS1025 is a single chip IC incorporating an integrated patch antenna with 8.5 dBi peak gain across the entire 60 GHz band The PRS1125 is a single chip IC with available 60 GHz Tx and Rx antenna ports allowing custom antenna designs The PRS2152 and PRS2153 are highly integrated module solutions with an available WR‐15 waveguide interface allowing simple interface to common 60 GHz waveguide components Applications Mobile multi‐gigabit wireless connectivity High quality, low latency, wireless UHD 4K display Wireless docking stations, I/O and mobile “sync‐and‐go” Small cell backhaul Wi‐Fi infrastructure and other multi‐gigabit links Standards Compatibility IEEE 802.11ad‐2012 (WiGig version 1.3): single carrier modulation and coding schemes IEEE 802.11‐2012 IEEE 802.1X‐2004 USB 3.0 Specification, Revision 1.0 FIPS PUB 197‐2001 Information furnished by Peraso Technologies is believed to be accurate and reliable. However, no responsibility is assumed by Peraso Technologies for its use, or responsibility for any infringements of patents or other rights of third parties that may result from its use. Specifications are subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Peraso Technologies. Trademarks and registered trademarks are the property of their respective owners. Peraso Technologies Inc. 144 Front St. West, Suite 685, Toronto, ON M5J 2L7 www.perasotech.com Revision 0.15.03 © 2015 Peraso Technologies. All Rights Reserved. Page | 2 .
Load more

Recommended publications
  • Understanding Technology Options for Deploying Wi-Fi
    Understanding Technology Options for Deploying Wi-Fi How Wi-Fi Standards Influence Objectives A Technical Paper prepared for the Society of Cable Telecommunications Engineers By Derek Ferro VP Advanced Systems Engineering Ubee Interactive 8085 S. Chester Street Suite 200 Englewood, CO 80112 [email protected] Bill Rink Senior Director Product Management Ubee Interactive 8085 S. Chester Street Suite 200 Englewood, CO 80112 [email protected] www.ubeeinteractive.com Introduction As Wi-Fi technology evolves at an exponential pace, Operators must understand available Wi-Fi standards in order to make the best business decisions when purchasing and deploying new wireless gateways (i.e. performance versus cost). This paper will discuss the migration from 802.11b, 802.11g, 802.11a, 802.11n and most recently the push to 802.11ac. It will also discuss the advancement of MIMO antenna technology from 1x1, 2x2, 3x3 and even 4x4. Many questions will be addressed: • What are the complexities of advanced MIMO? • When to implement which MIMO configuration? • What are alternative options for improving performance (power amplification, improved receive amplifiers, etc.)? • When should single band, dual-band selectable or dual-band concurrent gateways be deployed? • When examining the US residential market, what is the penetration of 2.4GHz, 5GHz, and dual-band homes, and what are the emerging trends in the marketplace? We hope to demystify the complexity surrounding Wi-Fi and look at the trade-offs in performance and cost presented by each option. www.ubeeinteractive.com Alphabet Soup: Understanding Wi-Fi Standards The Evolution of 802.11 Standards 802.11 technology has its origins in a 1985 ruling by the U.S.
    [Show full text]
  • 802.11 Alternate Phys February 2018
    CWNP 802.11 Alternate PHYs February 2018 802.11 Alternate PHYs A whitepaper by Ayman Mukaddam ©2018 CWNP, LLC CWNP Page 1 of 12 1005 Slater Road, Suite 101 • Durham, NC 27703 866-438-2963 • www.cwnp.com CWNP 802.11 Alternate PHYs February 2018 Contents Modern 802.11 Amendments ....................................................................................................................... 3 Traditional PHYs Review (2.4 GHz and 5 GHz PHYs) ..................................................................................... 3 802.11ad Directional Multi-Gigabit - DMG PHY ............................................................................................ 4 Frequency Band Used ............................................................................................................................... 4 Channel Plans ............................................................................................................................................ 5 Modulation Methods and Data Rates ....................................................................................................... 5 Use Cases .................................................................................................................................................. 6 802.11af TV High Throughput (TVHT) PHY ................................................................................................... 8 Frequency Band Used ..............................................................................................................................
    [Show full text]
  • W110 Wigig® Chipset Overview Features Application Diagram
    W110 WiGig Chipset Product Brief 2015‐12‐23 Overview The Peraso W110 chipset is targeted for WiGig applications and employs the PRS1125 and PRS4001 integrated circuits to implement the necessary IEEE 802.11ad functionality. The W110 chipset implements a complete SuperSpeed USB 3.0 to WiGig solution. The PRS4001 Low Power WiGig Baseband incorporates the Analog Front End, BB PHY/MAC, and two RISC CPU cores. The PRS1125 is a single chip direct conversion RF transceiver providing 60 GHz single‐ended receiver and transmit antenna interfaces. The chipset is ideal for wireless storage, wireless display, and multi‐gigabit mobile wireless applications. Features PRS4001 Low Power Baseband PRS1125 High Performance WiGig Radio IEEE 802.11ad compliant Tx output power: Up to +14 dBm Fully integrated AFE, PHY and MAC Better than ‐21 dB transmit EVM (16‐QAM) Highly flexible, dual CPU soft MAC integrates WiGig Receiver noise figure: < 5 dB MAC functions Receiver conversion gain > 70 dB PHY supports MCS0 to MCS12 (4.62 Gb/s) Integrated single‐ended 60 GHz antenna interfaces 2 Gb/s link at 10m (MCS8) PLL tunes to all channels of IEEE 802.11ad 1 Gb/s at 20m (MCS4) specifications using integrated XO 0.8 mm thick, 7mm × 7mm BGA 6mm × 6mm BGA Package Application Diagram Status LED Serial Flash Tx Antenna 2.5V 1.8V CPF 1.2V PWM SPI PRS4001 REFCLK 3.3V (USB) PRS1125 Bias 2.5V (IO) Peripherals MAC PHY AFE 1.1V (Core) SPI, I2C, PWM, UART, GPIO, LSADC, Upper MAC Memory DAC TX_I XREF1 JTAG (640K) WiGig PHY Tx Path Tx Data Path PLL USB 3.0 Upper MAC CPU DAC TX_Q XREF2 45 MHz USB 3 USB 3.0 Packet Buffer MAC/PHY IF PHY and Device/ PLL Digital AGC VCO XO Host Shared Memory GCMP (AES) (592K) USB 2 Encryption USB 2.0 PHY ADC RX_Q Lower MAC CPU Configuration WiGig PHY Rx Data Path and GPIO Lower MAC Memory Rx Path Control ADC RX_I GPIO (optional), SPI 256K SPI Radio Control SPI Rx Antenna Revision 0.15.12 © 2015 Peraso Technologies.
    [Show full text]
  • Medium Access Control for 60 Ghz Wireless Networks: a Comparative Review
    International Journal of Control and Automation Vol. 8, No. 4 (2015), pp. 421-434 http://dx.doi.org/10.14257/ijca.2015.8.4.39 Medium Access Control for 60 GHz Wireless Networks: A Comparative Review Rabin Bhusal1 and Sangman Moh2 1I&M Team, Telstra Corporation, Perth, Australia 2Dept. of Computer Eng., Chosun Univ., Gwangju, Korea [email protected], [email protected] Abstract The 60 GHz wireless networks enable multi-Gbps local communications. With opportunities, however, there are many challenges because the physical wave characteristics of the 60 GHz band are quite different from those of the currently used 2.4 GHz and 5 GHz ISM bands. Moreover, there are many hot issues associated with the MAC (Medium Access Control) layer as the directional MAC protocols proposed for 2.4 GHz and 5 GHz cannot be directly implemented on the 60 GHz frequency because of different characteristics of the millimeter waves. However, no review on MAC for 60 GHz wireless networks has been reported in the literature. In this paper, we comparatively review standards and protocols of MAC in 60 GHz wireless networks for multi-Gbps communications. Opportunities and challenges are also discussed. Keywords: 60 GHz, millimeter wave, multi-Gbps, medium access control, directional antenna, ISM band. 1. Introduction Wireless local area networks (WLANs) based on IEEE 802.11 standards, also commercially known as Wi-Fi, have become an integral part of our daily living, and this technology is being integrated into many devices like smart phones, laptops, and other consumer electronics. The rapid increase of throughput from 2 Mbps in 802.11 to as much as 600 Mbps in 802.11n has provided many opportunities and led to a new goal to achieve speeds in the Gbps range.
    [Show full text]
  • Toward a Reliable Network Management Framework
    TOWARD A RELIABLE NETWORK MANAGEMENT FRAMEWORK A DISSERTATION IN Computer Networking and Communications Systems and Economics Presented to the Faculty of the University of Missouri–Kansas City in partial fulfillment of the requirements for the degree DOCTOR OF PHILOSOPHY by HAYMANOT GEBRE-AMLAK University of Missouri - Kansas City Kansas City, Missouri 2018 © 2018 HAYMANOT GEBRE-AMLAK ALL RIGHTS RESERVED TOWARD A RELIABLE NETWORK MANAGEMENT FRAMEWORK Haymanot Gebre-Amlak, Candidate for the Doctor of Philosophy Degree University of Missouri–Kansas City, 2018 ABSTRACT As our modern life is very much dependent on the Internet, measurement and management of network reliability is critical. Understanding the health of a network via outage and failure analysis is especially essential to assess the reliability of a network, identify problem areas for network reliability improvement, and characterize the network behavior accurately. However, little has been known on characteristics of node outages and link failures in access networks. In this dissertation, we carry out an in-depth outage and failure analysis of a university campus network using a rich set of node outage and link failure data and topology information over multiple years. We investigated the diverse statistical characteristics of both wired and wireless networks using big data analytic tools for network management. Furthermore, we classify the different types of network failures and management issues and their strategic resolution. iii While the recent adoption of Software-Defined Networking (SDN) and softwariza- tion of network functions and controls ease network reliability, management, and vari- ous network-level service deployments, the task of monitoring network reliability is still very challenging.
    [Show full text]
  • On IEEE 802.11: Wireless LAN Technology
    Preprint: http://arxiv.org/abs/1307.2661 Original Publication: International Journal of Mobile Network Communications & Telematics (IJMNCT) Vol. 3, Issue. 4, 2013. [DOI: 10.5121/ijmnct.2013.3405] On IEEE 802.11: Wireless LAN Technology Sourangsu Banerji1, Rahul Singha Chowdhury2 1, 2 Department of Electronics & Communication Engineering, RCC-Institute of Information Technology, India ABSTRACT: Network technologies are WMAN: Wireless Metropolitan Area Network; traditionally based on wireline solutions. But generally cover wider areas as large as entire cities. the introduction of the IEEE 802.11 standards WWAN: Wireless Wide Area Network with a cell have made a huge impact on the market such radius about 50 km, cover areas larger than a city. that laptops, PCs, printers, cellphones, and However out of all of these standards, WLAN VoIP phones, MP3 players in our homes, in and recent developments in WLAN technology offices and even in public areas have would be our main area of study in this paper. The incorporated the wireless LAN technology. IEEE 802.11 is the most widely deployed WLAN Wireless broadband technologies nowadays technology as of today. Another well known is the provide unlimited broadband access to users HiperLAN standard by ETSI. Both these which were previously offered only to wireline technologies are united under the Wireless Fidelity users. In this paper, we review and summarize (Wi-fi) alliance. In literature though, IEEE802.11 one of the emerging wireless broadband and Wi-fi is used interchangeably and we will also technology i.e. IEEE 802.11,which is a set of follow the same convention in this paper.
    [Show full text]
  • GISFI 5G Workshop
    GISFI 5G Workshop Sri Chandra Standards Senior Manager, IEEE-SA Evolution of xG systems Standards Next Generation Mobile Telephony released every 10 years 1G: Nordic Mobile Telephone introduced in 1981 2G: released in 1991 (GSM) 3G: 2001 (IMT-2000 and UMTS) – Cdma/IS95 released in 1995 in the US 4G: Fully compliant with IMT Advanced standardized in 2012 – Mobile WiMAX in 2006 – First release LTE in 2009 5G: Approximately 2020 Source: Wikipedia IMT Advanced Requirements IEEE has been engaged in Wireless Mobile Telephony for a very long time; In Connection with next generation standards: Does not support traditional circuit-switched, but all-IP based communication Spread spectrum technology in 3G replaced by frequency domain equalization (OFDMA) Specific data rates specified for high and low mobility users (100 mbps, 1gbs) Smooth handovers across heterogeneous networks IEEE Standards IEEE has been engaged in Wireless Mobile Telephony for a very long time; In Connection with next generation standards: Two 4G candidate systems have been commercially deployed: ITU-R specified set of requirements for 4G standards, named IMT-A (International Mobile Telecommunications Advanced), with peak speed requirements for 4G at 100 megabits-per-second for highly mobile communications and 1Gbits per second for low mobility First release Long Term Evolution (LTE) Standard first released in 2009 Mobile WiMAX (Worldwide Interoperability for Microwave Access): IEEE 802.16e-2005 – WirelessMAN Advanced Evolution Standard based on 802.16m – Enabling
    [Show full text]
  • Wigig White Paper
    White Paper Defining the Future of Multi-Gigabit Wireless Communications July 2010 WiGig | Defining the Future of Multi-Gigabit Wireless Communications 2 Introduction Specification Overview The widespread availability and use of digital The WiGig specification includes key features to multimedia content has created a need for faster maximize performance, minimize implementation wireless connectivity that current commercial standards complexity and cost, enable compatibility with existing cannot support. This has driven demand for a single Wi-Fi and provide advanced security. Key features standard that can support advanced applications include: such as wireless display and docking, as well as more • Support for data transmission rates up to 7 Gbps; established usages such as network access. all devices based on the WiGig specification will be capable of gigabit data transfer rates The Wireless Gigabit (WiGig) Alliance was formed to • Designed from the ground up to support low-power meet this need by establishing a unified specification handheld devices such as cell phones, as well as for wireless communication at multi-gigabit speeds; this high-performance devices such as computers; specification is designed to drive a global ecosystem of includes advanced power management interoperable products. • Based on IEEE 802.11; provides native Wi-Fi The WiGig MAC and PHY Specification enables data support and enables devices to transparently switch rates up to 7 Gbps, more than 10 times the speed of between 802.11 networks operating in any frequency the fastest Wi-Fi networks based on IEEE 802.11n. It band including 2.4 GHz, 5 GHz and 60 GHz operates in the unlicensed 60 GHz frequency band, • Support for beamforming, maximizing signal which has much more spectrum available than the strength and enabling robust communication at 2.4 GHz and 5 GHz bands used by existing Wi-Fi distances beyond 10 meters products.
    [Show full text]
  • Wireless LAN IEEE 802.11 Aka Wi-Fi
    WLAN IEEE 802.11 aka Wi-Fi Max Riegel ©Max Riegel, 2019 Lectures overview June 27th – Wi-Fi deployments – Standardization environment – Wi-Fi system architecture – Wi-Fi security July 4th – Medium access functions – MAC layer management frame formats – Quality of Service – Wi-Fi roaming and Hotspot 2.0 – WLAN management July 11th – Wireless channel characteristics – Wi-Fi radio for 2.4 GHz and 5 GHz bands – WiGig extension for 60 GHz bands – HaLow extension for below 1GHz bands SON Self Organizing Networks SS2019 (WLAN) ©Max Riegel, 2019 2019-07-11 2 Standards environments STANDARD REFERENCE SON Self Organizing Networks SS2019 (WLAN) ©Max Riegel, 2019 2019-07-11 3 IEEE Std 802.11™-2016 + amendment 802.11ah • Can be downloaded at no charge by IEEE Get Program – http://standards.ieee.org/getieee802/download/802.11-2016.pdf – http://standards.ieee.org/getieee802/download/802.11ah-2016.pdf • No all the features specified in the standard are available in real Wi-Fi products • Where appropriate presentation adopts behavior of real Wi-Fi products as specified by Wi-Fi Alliance in its certification programs – https://www.wi-fi.org/discover-wi-fi/specifications Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications • Revision of IEEE Std 802.11-2012 – Previous revisions: IEEE Std 802.11-2007 and IEEE Std 802.11-1999 – Initial IEEE 802.11 standard release in 1997 • Comprises initial IEEE Std 802.11-1999 together with all amendments IEEE 802.11a-1999 … IEEE 802.11af-2013 – i.e.: a, b, d, e, g, h, I, j, k, n, p,
    [Show full text]
  • Improving Spatial Reuse in Future Dense High Efficiency Wireless Local Area Networks
    Improving spatial reuse in future dense high efficiency Wireless Local Area Networks Imad Jamil To cite this version: Imad Jamil. Improving spatial reuse in future dense high efficiency Wireless Local Area Networks. Networking and Internet Architecture [cs.NI]. INSA de Rennes, 2015. English. NNT : 2015ISAR0033. tel-01329810 HAL Id: tel-01329810 https://tel.archives-ouvertes.fr/tel-01329810 Submitted on 9 Jun 2016 HAL is a multi-disciplinary open access L’archive ouverte pluridisciplinaire HAL, est archive for the deposit and dissemination of sci- destinée au dépôt et à la diffusion de documents entific research documents, whether they are pub- scientifiques de niveau recherche, publiés ou non, lished or not. The documents may come from émanant des établissements d’enseignement et de teaching and research institutions in France or recherche français ou étrangers, des laboratoires abroad, or from public or private research centers. publics ou privés. Thèse THESE INSA Rennes présentée par sous le sceau de l’Université européenne de Bretagne pour obtenir le titre de Imad Jamil DOCTEUR DE L’INSA DE RENNES ECOLE DOCTORALE : MATISSE Spécialité : Electronique et Télécommunications LABORATOIRE : IETR Sandrine DESTOUET ROBLOT Improving spatial reuse Docteur-Ingénieur à Orange Labs Rennes / Membre invité in future dense high Thèse soutenue le 17.12.2015 eficiency Wireless Local devant le jury composé de : Hikmet SARI Area Networks Professeur à Centrale-Supelec à Gif sur Yvette / Président André-Luc BEYLOT Professeur à l’ENSEEIHT de Toulouse / Rapporteur
    [Show full text]
  • MIMO Beamforming in Millimeter-Wave Directional Wi-Fi 1
    Ho et al ., MIMO beamforming in millimeter-wave directional Wi-Fi 1 MIMO Beamforming in Millimeter-Wave Directional Wi-Fi Keang-Po Ho, Senior Member, IEEE , Shi Cheng, Member, IEEE and Jianhan Liu, Member, IEEE arrays are used in both transmitter and receiver, as shown in Abstract —Beamforming is indispensable in the operation of Figure 1, the whole array with many antennas are used to 60-GHz millimeter-wave directional multi-gigabit Wi-Fi. Simple transmit one SISO data stream. Analog phase shifters are used power method and its extensions enable the transmitting and to form a single spatial beam, basically pointing the receiving antenna arrays to form a beam for single spatial transmitter and receiver toward each other, providing multi- stream. To further improve the spectral efficiency in future 60- GHz directional Wi-Fi, alternating least square (ALS) algorithm gigabit yet directional transmission. SISO beamforming based can form multiple beams between the transmitter and receiver on the simple power method is well-known and can be very for multi-input-multi-output (MIMO) operations. For both effective for frequency-flat channel. Beamforming in shared and split MIMO architecture, the ALS beamforming frequency-selective channel is less well-known but can be algorithm can be operated in both frequency-flat and frequency- performed using alternating least square (ALS) method that selective channels. In the split architecture, MIMO beamforming finds iteratively the transmitter beamforming vector by fixing approximately maximizes the capacity of the beam-formed MIMO channel. that of the receiver, and then the other way around. Index Terms —Millimeter wave, MIMO, beamforming, SISO operation for 60-GHz millimeter wave is a mature directional multi-gigabit Wi-Fi technology, defined and operated in all 60-GHz standards.
    [Show full text]
  • Wigig and IEEE 802.11Ad for Multi-Gigabyte-Per-Second WPAN
    WiGig and IEEE 802.11ad For Multi-Gigabyte-Per-Second WPAN and WLAN SaiShankar N, Debashis Dash, Hassan El Madi, and Guru Gopalakrishnan Tensorcom Inc., 5900 Pasteur Court, Carlsbad, CA 92008 Abstract: The Wireless Gigabit Alliance (WiGig) and IEEE 802.11ad are developing a multigigabit wireless personal and local area network (WPAN/WLAN) specification in the 60 GHz millimeter wave band. Chipset manufacturers, original equipment manufacturers (OEMs), and telecom companies are also assisting in this development. 60 GHz millimeter wave transmission will scale the speed of WLANs and WPANs to 6.75 Gbit/s over distances less than 10 meters. This technology is the first of its kind and will eliminate the need for cable around personal computers, docking stations, and other consumer electronic devices. High-definition multimedia interface (HDMI), display port, USB 3.0, and peripheral component interconnect express (PCIe) 3.0 cables will all be eliminated. Fast downloads and uploads, wireless sync, and multi-gigabit-per-second WLANs will be possible over shorter distances. 60 GHz millimeter wave supports fast session transfer (FST) protocol, which makes it backward compatible with 5 GHz or 2.4 GHz WLAN so that end users experience the same range as in today’s WLANs. IEEE 802.11ad specifies the physical (PHY) sublayer and medium access control (MAC) sublayer of the protocol stack. The MAC protocol is based on time-division multiple access (TDMA), and the PHY layer uses single carrier (SC) and orthogonal frequency division multiplexing (OFDM) to simultaneously enable low-power, high-performance applications. Keywords: 60 GHz communications; IEEE standards; WiGig; 802.11ad; contention based access protocol; scheduled protocol; Beamforming; power save 1 Introduction There is a huge amount of unlicensed spectrum available worldwide in the 60 GHz band.
    [Show full text]