®

Installation instructions for part INST-7800

Acura/Honda 1990-2002 Contents INST-7800 Installation Instructions Section INSTALLATION INSTRUCTIONS - 99-7888...... 1.0 • 99-7888 • 99-7889 • 99-7890 • 99-7891 - 99-7889...... 2.0 • 99-7892 • 99-7893 • 99-7894 • 99-7895 - 99-7890...... 3.0 - 99-7891...... 4.0 TOOLS REQUIRED - 99-7892...... 5.0 Refer to each section title page. - 99-7893...... 6.0 - 99-7894...... 7.0 - 99-7895...... 8.0 APPLICATION OVERVIEW INST-7800 is a collection of installation instruction booklets. 99-7888 99-7890/99-7892 99-7891 Use the Application Overview when selecting which Acura Integra 1990-2001 Acura CL 1997-1999 Honda Civic 1996-1998 installation instruction selection to use. Each section is setup Acura Legend 1990-1996 Acura Integra 1990-2001 99-7893 as a chapter with its own table of contents. Acura TL 1996-1998 Acura Legend 1990-1996 Honda CR-V 1997-2001 Acura Vigor 1992-1994 Acura TL 1996-1998 Honda Prelude 1997-2001 Honda Accord 1990-1993 Acura Vigor 1992-1994 Honda Odyssey 1995-1998 Honda Accord 1990-1997 99-7894/99-7895 Isuzu Oasis 1996-1999 Honda Odyssey 1995-1998 Honda Accord 1998-2002 99-7889 Isuzu Oasis 1996-1999 Honda Prelude 1992-1996 CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling APPLICATIONS the ignition. Also, do not remove the factory radio with the key in the

REV. 10/12/2016 INST-7800 REV. See application list inside cover on position, or while the vehicle is running.

METRA - The World’s best kits ® metraonline.com © COPYRIGHT 2016 METRA ELECTRONICS CORPORATION ®

99-7888

Section 1 F G Dash Disassembly Acura/Honda/Isuzu Acura Integra 1990-1993 1990-2001 1. Remove (3) screws from each side of the center 99-7888 console and remove the console. TOOLS REQUIRED 2. Remove (2) screws securing the factory radio to KIT FEATURES the sub-dash support bracket. • Phillips screwdriver • Cutting tool • Socket wrench • 2-shaft radio provision • DIN radio provision 3. Slide the radio/pocket assembly out and • Equalizer provision • Rear support provision disconnect the wiring. (Figure A) Table of Contents 4. Locate the radio housing. (Figure B) KIT COMPONENTS Dash Disassembly Continue to kit assembly for • A) Radio housing • B) Trimplate • C) Radio support – Acura Integra 1990-1993...... 1.0 ALL VEHICLES, Section 1 • D) Mounting bracket • E) Equalizer dummy plate – Acura Integra 1994-2001...... 1.1 • F) Shaft masks • G) (2) Pal nuts – Acura Legend 1990...... 1.1 A B – Acura Legend 1991-1996...... 1.1 – Acura TL 1996-1998...... 1.2 – Acura Vigor 1992-1994...... 1.2 – Honda Accord 1990-1993...... 1.3 – Honda Odyssey 1995-1998...... 1.3 – Isuzu Oasis 1996-1999...... 1.3 D E Kit Assembly – 2-shaft radio provision...... 1.4 C – DIN radio provision...... 1.5 (Figure A) (Figure B) 1.0 ®

99-7888

Dash Disassembly

Acura Integra 1994-2001 5. Remove the gear shifter knob Acura Legend 1990 removing the Acura Legend 1991-1996 and unsnap the shifter trim. shaded portions 1. Remove the cover cap located 1. Remove (2) screws of the housing lip. 1. Remove (2) screws below the ashtray. under the emergency brake and 6. Remove (2) screws below the below the ashtray. (Figure B) (Figure A) remove (2) screws exposed. radio opening and remove (Figure A) Continue to kit 2. Unclip the dash trim bezel and the upper dash trim bezel. 2. Unclip the dash assembly for 2. Remove (2) screws from the trim bezel then disconnect the cigarette lighter wiring and rear corners of the lower 7. Remove (2) 8mm screws ALL VEHICLES, disconnect the Section 1 remove the bezel. dash trim bezel and remove. securing the factory radio cigarette lighter (Figure A) and disconnect the wiring. wiring and remove 3. Remove (2) bolts securing the the bezel. rear of the factory radio and 3. Remove the ashtray and (2) 8. Locate the radio housing. disconnect the wiring. screws exposed. (Figure A) (Figure B) 3. Remove (2) bolts securing the rear 4. Locate the radio housing. (Figure B) 4. Unsnap the ashtray housing Continue to kit assembly for of the factory radio and disconnect the cigarette ALL VEHICLES, Section 1 and disconnect the Continue to kit assembly for lighter harness. wiring. ALL VEHICLES, Section 1 4. Modify the factory radio housing by cutting and (Figure A)

¼” ¼” ¾” ¾” Factory radio housing opening 1¼” 1¼” 1” 1” (Figure A) (Figure B) (Figure B) (Figure A) (Figure B) 1.1 ®

99-7888

Dash Disassembly Acura TL 1996-1998 the metal housing and slide the Acura Vigor 1992-1994 6. Lift up on the center console and radio out. remove. 1. Using a small screwdriver, unclip the 1. Remove the access cap from the climate perimeter of the radio trim bezel. Note, it is NOT necessary to control cluster and (1) screw exposed. 7. Unclip the radio trim bezel and (Figure A) remove the screws securing the disconnect the wiring. 2. Disconnect the climate control metal housing to the bezel. 2. Unclip the cluster and remove (2) screws 8. Remove (2) bolts from the back and rear defroster wiring and exposed. of the factory radio and disconnect the remove the bezel. 5. Disconnect the wiring. 3. Remove the ashtray and (2) Phillips wiring. 3. Remove (4) Phillips screws 6. Cut and remove the top clips screws exposed. (Figure A) 9. Modify the factory radio housing by securing the factory radio/trim from the radio housing. 4. Remove the cover caps from each front cutting and removing the shaded bezel assembly. (Figure A) (Figure B) corner of the center console and the portions of the housing lip. (Figure B) screws exposed. 4. Loosen (2) Phillips screws Continue to kit assembly for Continue to kit assembly for ALL 5. Open the storage compartment, lift up the VEHICLES, Section 1 securing the back of the radio to ALL VEHICLES, Section 1 carpet and remove (2) screws exposed.

¼” ¼”

¾” ¾” Factory radio housing opening 1¼” 1” 1” 1¼”

(Figure A) (Figure B) (Figure A) (Figure B) 1.2 ®

99-7888

Dash Disassembly

Honda Accord 1990-1993 Honda Odyssey 1995-1998 5. Remove (1) Phillips screw from the coin tray Isuzu Oasis 1996-1999 and then remove (1) Phillips screw under 1. Remove (4) screws from the lower portion of the center the ignition. console. (Figure A) 1. Remove (2) 8mm screws under the glove box. 2. Remove the gear shifter knob and lift the console out. 6. Remove (4) Phillips screws securing the 2. Remove (1) Phillips screw on the glove box factory cupholder. 3. Remove the ashtray and ashtray bracket. arm and remove the box. 7. Remove (2) 8mm hex-head 4. Remove (2) screws from the bottom of the radio support, 3. Remove (2) Phillips screws exposed in the screws from the rear support bracket and slide the unit out and disconnect the wiring. glove box cavity then remove (2) Phillips disconnect the wiring. screws below the storage box door (under the 5. Locate the radio housing. (Figure B) ashtray). (Figure A) 8. Locate the radio housing. (Figure B) Continue to kit assembly for ALL VEHICLES, Section 1 4. Remove (2) screws from the left side of the Continue to kit assembly for dash console. ALL VEHICLES, Section 1

(Figure A) (Figure B) (Figure A) (Figure B) 1.3 ®

99-7888

Kit Assembly

All Vehicles 5. If an equalizer will be included: 2-shaft radio provision: Slide the aftermarket equalizer into the back of the radio housing. Using the hardware included with the equalizer, secure the unit to the kit. (Figure B) 1. Attach the trim plate and shaft masks to the radio housing. (Figure A1) 2. Slide the radio into the kit and secure with shaft nuts. (Figure A1) If an equalizer will NOT be included: Continue to Step 5 Snap the Equalizer Dummy Plate into the radio housing. (Figure C) DIN radio provision: 6. Insert the Radio Support into the Mounting Bracket. (Figure D) 1. . Cut and remove the shaft supports from the radio housing. 7. Turn the Radio Support to lock into place. (Figure E) 2. . Remove the metal DIN sleeve from the aftermarket radio. 8. Secure the assembly to the factory mounting plate in the sub-dash with (2) Pal 3. . Slide the sleeve into the kit and secure by bending the metal locking tabs down. Nuts supplied. (Figure F) 4. . Slide the radio into the sleeve until it clicks in. (Figure A2) Continue on the next page Continue to Step 5

(Figure A1) (Figure A2) (Figure B) (Figure C) 1.4 ®

99-7888

Kit Assembly

8. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation. 9. Integra, Accord, Odyssey, Oasis: Snap the completed assembly into the sub-dash. (Figure G) Legend, TL, Vigor: Snap the completed assembly into the factory trim bezel. Secure the bezel to the dash with those screws previously removed. (Figure H) 10. Reassemble the dash in reverse order of disassembly. (Figure D) (Figure E)

(Figure F) (Figure G) (Figure H) 1.5 ®

99-7889

Section 2 F Dash Disassembly (Cont) Honda Prelude 3. Pull up on the console trim bezel and remove. 1992-1996 E 4. Using an angled screwdriver, remove (2) screws 99-7889 securing the gear shifter bracket to the bezel. TOOLS REQUIRED (Figure A) KIT FEATURES • Phillips screwdriver • Cutting tool • Socket wrench 5. Remove (4) screws from the radio trim bezel, • 2-shaft radio provision • DIN radio provision remove the factory radio assembly and disconnect • Equalizer provision • Rear support provision Table of Contents the wiring. (Figure B) Continue to kit assembly for KIT COMPONENTS Dash Disassembly...... 2.0 ALL VEHICLES, Section 2 • A) Radio housing • B) Trimplate • C) Shaft masks Kit Assembly • D) Equalizer dummy plate • E) Radio support – 2-shaft radio provision...... 2.1 • F) Mounting bracket – DIN radio provision...... 2.1 A B

Dash Disassembly

1. Remove (2) screws from the top of the console trim C D bezel. (Figure A) 2. Slide the front seats back and remove (4) Phillips screws from each side of the bezel. (Figure A) (Figure A) (Figure B) 2.0 ®

99-7889

Kit Assembly

All Vehicles DIN radio provision: 5. If an equalizer will be included: 9. Locate the factory wiring harness in the dash. Metra recommends using 2-shaft radio provision: 1. Remove the metal DIN sleeve from Slide the unit into the back of the the aftermarket radio. radio housing and secure. the proper mating adapter from 1. Attach the trim plate and shaft If an equalizer will not be included: Metra or AXXESS. Test the radio for masks to the radio housing. 2. Cut and remove the shaft supports proper operation. (Figure A) from the radio housing. Snap the equalizer dummy plate into the opening. 10. Snap the completed assembly into 3. Slide the sleeve into the housing and 2. Slide the aftermarket radio into 6. Insert the radio support into the the radio trim bezel and secure the the kit. (Figure A) secure by bending the metal locking mounting bracket. (Figure C) bezel to the dash with those screws tabs down. (Figure B) 3. Secure with shaft nuts. (Figure A) 7. Turn the radio support to lock into previously removed. (Figure F) 4. Slide the radio into the sleeve until it place. (Figure D) Continue to Step 5 clicks in. (Figure B) 11. Reassemble the dash in reverse 8. Secure the assembly to the factory order of disassembly. Continue to Step 5 mounting plate in the sub-dash with (2) Pal Nuts supplied. (Figure E)

(Figure A) (Figure B) (Figure C) (Figure D) (Figure E) (Figure F) 2.1 ®

99-7890

Section 3 F G Table of Contents Acura/Honda/Isuzu Honda 1990-2001 E – Accord 1990-1993...... 3.5 – Accord 1994-1997...... 3.6 99-7890 H I – Odyssey 1995-1998...... 3.6-3.7 KIT FEATURES Isuzu – Oasis 1996-1999...... 3.6-3.7 • 2-shaft radio provision • DIN radio provision • Equalizer provision • Rear support provision Kit Assembly TOOLS REQUIRED – 2-shaft radio provision...... 3.7-3.8 KIT COMPONENTS • Phillips screwdriver • Cutting tool • Socket wrench – DIN radio provision...... 3.7-3.8 • A) Radio housing • B) Rear support bracket Dash Disassembly • C) Shaft supports • D) (2) Nuts • E) Radio support Table of Contents • F) Mounting bracket • G) Equalizer dummy plate Acura CL 1997-1999 • H) (2) Carriage bolts • I) (2) Pal nuts Dash Disassembly 1. Unclip the radio trim bezel and disconnect the A B Acura clock and climate control wiring. (Figure A) – CL-1999...... 3.0-3.1 2. Remove (2) 8mm hex-head screws securing the – Integra 1990-1993...... 3.1 factory radio and disconnect the wiring. – Integra 1994-2001...... 3.2 3. Locate the radio housing and then cut and remove the side clips from the radio housing. (Figure B and C) – Legend 1990...... 3.2-3.3 C D 4. Secure the rear support bracket to the bottom tab – Legend 1991-1996...... 3.3 on the radio housing with (2) carriage bolts and (2) – TL 1996-1998...... 3.4 nuts. (Figure D) – Vigor 1992-1994...... 3.4-3.5 Continue to kit assembly for ALL VEHICLES, Section 3

3.0 ®

99-7890

Acura CL 1997-1999 (Cont) Dash Disassembly Acura Integra 1990-1993 7. Secure the assembly to the factory mounting plate 1. Remove (3) screws from each side of the center in the sub-dash with (2) pal nuts supplied. console and remove the console. (Figure A) (Figure D) 2. Remove (2) screws securing the factory radio to the Continue to kit assembly for ALL VEHICLES, sub-dash support bracket. Section 3 3. Slide the radio/pocket assembly out and disconnect the wiring. 4. Cut and remove the top clips and bottom tab from the radio housing. (Figure B) 5. Insert the radio support into the mounting bracket. (Figure A) (Figure B) (Figure C) 6. Turn the radio support to lock into place. (Figure C) (Figure C)

(Figure C) (Figure D) (Figure A) (Figure B) (Figure D) 3.1 ®

99-7890 Dash Disassembly

Acura Integra 1994-2001 4. Remove the gear shifter knob 8. Insert the radio support into Acura Legend 1990 and unsnap the shifter trim. the mounting bracket. Turn the 1. Remove (2) screws 1. Remove the cover cap located radio support to lock into place. below the ashtray. under the emergency brake and 5. Remove (2) screws below the (Figure C) remove (2) screws exposed. radio opening and remove the Unclip the dash trim (Figure A) upper dash trim bezel. 9. Secure the assembly to the bezel. (Figure A) factory mounting plate in the 2. Remove (2) screws from the rear 6. Remove (2) 8mm screws 2. Disconnect the sub-dash with (2) pal nuts cigarette lighter wiring corners of the lower dash trim securing the factory radio and supplied. (Figure D) bezel and remove. (Figure A) disconnect the wiring. and remove the bezel. Continue to kit assembly for 3. Remove (2) bolts 3. Remove the ashtray and (2) 7. Cut and remove the top clips ALL VEHICLES, Section 3 screws exposed. Unsnap the and bottom tab from the radio securing the rear of ashtray housing and disconnect housing. (Figure B) the factory radio and (Figure A) the cigarette lighter harness. disconnect the wiring. 4. Cut and remove the top clips and bottom tab from the radio housing. (Figure B) 5. Insert the radio support into the mounting bracket. Turn the radio support to lock into place. (Figure C) 6. Secure the assembly to the sub-dash mounting plate with (2) pal nuts supplied. (Figure D) 7. Modify the factory radio housing by trimming the shaded portions of the housing lip. (Figure E) Continue to kit assembly for (Figure A) (Figure B (Figure C) (Figure D) ALL VEHICLES, Section 3 3.2 ®

99-7890

Acura Legend 1990 (Cont) Dash Disassembly Acura Legend 1991-1996 1. Remove (2) screws below the ashtray. Unclip the dash trim bezel. (Figure A) 2. Disconnect the cigarette lighter wiring and remove the bezel. 3. Remove (2) bolts securing the rear of the factory radio and disconnect the wiring. (Figure B) (Figure C) 4. Cut and remove the top clips and (Figure A) (Figure B) bottom tab from the radio housing. ¼” ¼” (Figure B) ¾” 5. Insert the radio support into the 1¼” mounting bracket. Turn the radio support to lock into place. (Figure C) 6. Secure the assembly to the factory 1” 1” mounting plate in the sub-dash with Factory radio (2) pal nuts supplied. (Figure D) housing opening Continue to kit assembly for ALL (Figure D) (Figure E) VEHICLES, Section 3 (Figure C) (Figure D) 3.3 ®

99-7890 Dash Disassembly

Acura TL 1996-1998 Acura Vigor 1992-1994 1. Using a small screwdriver, unclip the 1. Remove the access cap from the climate control perimeter of the radio trim bezel. cluster and (1) screw exposed. (Figure A) 2. Unclip the cluster and remove (2) screws exposed. 2. Disconnect the climate control (Figure A) and rear defroster wiring and remove the bezel. 3. Remove the ashtray and (2) Phillips screws exposed. 3. Remove (4) Phillips screws securing 4. Remove the cover caps from each front corner of the factory radio/trim bezel the center console and the screws exposed. assembly. (Figure A) 5. Open the storage compartment, lift up the carpet 4. Loosen (2) Phillips screws securing and remove (2) screws exposed. the back of the radio to the metal (Figure A) (Figure B) 6. Lift up on the center console and remove. Unclip housing. the radio trim bezel and disconnect the wiring. 5. Disconnect the wiring. Cut and 7. Remove (2) bolts from the back of the factory radio remove the top clips and bottom tab and disconnect the wiring. from the radio housing. (Figure B) 8. Cut and remove the top clips and bottom tab from 6. Insert the radio support into the the radio housing. (Figure B) mounting bracket. Turn the radio 9. Insert the radio support into the mounting bracket. support to lock into place. (Figure C) Turn the radio support to lock into place. 7. Secure the assembly to the factory 10. Secure the assembly to the sub-dash mounting mounting plate in the sub-dash with plate with (2) pal nuts supplied. (Figure C) (2) pal nuts supplied. (Figure D) 11. Modify the factory radio housing by trimming the Continue to kit assembly for shaded portions of the housing lip. (Figure D) ALL VEHICLES, Section 3 (Figure C) (Figure D) Continue to kit assembly for ALL VEHICLES, Section 3 3.4 ®

99-7890

Acura Vigor 1992-1994 (Cont) Dash Disassembly

Honda Accord 1990-1993 1. Remove (4) screws from the lower portion of the center console. (FIgure A) 2. Remove the gear shifter knob and lift the console out. Remove the ashtray and ashtray bracket. 3. Remove (2) screws from the bottom of the radio support, slide the unit out and disconnect the wiring. (Figure A) (Figure B) (Figure A) (Figure B) 4. Cut and remove the top clips and bottom tab from the radio housing. ¼” ¼” (Figure B) ¾” 5. Insert the radio support into the 1¼” mounting bracket. Turn the radio support to lock into place. (Figure C) 6. Secure the assembly to the factory 1” 1” mounting plate in the sub-dash with Factory radio (2) pal nuts supplied. (FIgure D) housing opening Continue to kit assembly for (Figure C) (Figure D) ALL VEHICLES, Section 3 (Figure C) (Figure D) 3.5 ®

99-7890 Dash Disassembly

Honda Accord 1994-1997 Honda Odyssey 1995-1998 Isuzu Oasis 1996-1999 1. Remove the ashtray and (1) 3/4” #8 Phillips screw exposed. 1. Remove (2) 8mm screws under the glove box and then remove (1) Phillips screw on the glove box 2. Open the storage compartment arm and remove the box. and remove (2) #8 Phillips screws exposed. 2. Remove (2) Phillips screws exposed in the glove box cavity. 3. Remove the cupholder tray and (3) #8 Phillips screws inside. (Figure A) 3. Remove (2) Phillips screws below the storage box door (under the ashtray). 4. Lift the center console out and 4. Remove (2) screws from the left side of the dash remove (2) Phillips screws exposed at console and then remove (1) Phillips screw from the base of the dash trim bezel. Unclip the bezel and remove. (Figure A) (Figure A) (Figure B) the coin tray. 5. Remove (1) Phillips screw under the ignition and 5. Remove (2) hex-head screws then remove (4) Phillips screws securing the securing the factory radio and factory cupholder. disconnect the wiring. 6. Remove (2) 8mm hex-head screws from the rear 6. Locate the radio housing and then support bracket and disconnect the wiring. cut and remove the side clips from the radio housing. (Figure B and C) 7. Cut and remove the top clips and bottom tab from the radio housing. (Figure B) 7. Secure the rear support bracket to the 8. Insert the radio support into the mounting bracket. bottom tab on the radio housing with Turn the radio support to lock into place. (Figure C) (2) carriage bolts and (2) keps nuts. (Figure D) 9. Secure the assembly to the factory mounting plate in the sub-dash with (2) pal nuts supplied. (Figure D) Continue to kit assembly for ALL VEHICLES, Section 3 (Figure C) (Figure D) Continue to kit assembly for ALL VEHICLES, Section 3 3.6 ®

99-7890

Kit Assembly Honda Odyssey 1995-1998 (Cont) Isuzu Oasis 1996-1999 All Vehicles 2-shaft radio provision: 1. Snap the shaft supports into the radio housing. (Figure A) 2. Slide the radio into the kit and secure with shaft nuts. (Figure A) Continue on the next page, Step 4

(Figure A) (Figure B) (Figure A) DIN radio provision: 1. Remove the metal DIN sleeve from the aftermarket radio. 2. Slide the sleeve into the kit and secure by bending the metal locking tabs down. 3. Slide the radio into the sleeve until it clicks in. (Figure B) Continue on the next page, Step 4

(Figure C) (Figure D) (Figure B) 3.7 ®

99-7890

Kit Assembly Notes

All Vehicles (Cont) 4. If an equalizer will be included: Slide the unit into the back of the radio housing and secure. If an equalizer will not be included: Snap the equalizer dummy plate into the opening. 5. Locate the factory wiring harness and connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation. (Figure A) 6. Accord 1990-1993, Integra, Odyssey, Oasis: Snap the completed assembly into the sub-dash. Legend, TL, Vigor: Snap the completed assembly into the factory trim bezel. Secure the bezel to the dash with those screws previously removed. (Figure A) Accord 1994-1997, CL: Slide the completed assembly into the sub-dash and secure the rear support bracket to the rear support provision with (2) hex-head bolts previously removed. (Figure B)

(Figure B) 3.8 ®

99-7891

Section 4 F Dash Disassembly (Cont) Honda Civic 3. Pull straight down on the lower steering column 1996-1998 panel and remove the panel. 4. Remove (2) Phillips screws under the climate 99-7891 TOOLS REQUIRED control panel.

KIT FEATURES • Phillips screwdriver • Cutting tool • Socket wrench 5. Remove (4) Phillips screws from the lower dash location. • 2-shaft radio provision • DIN radio provision 6. Remove (2) 8mm hex-head screws securing the • Rear support provision Table of Contents bottom-rear of the factory radio and disconnect the KIT COMPONENTS wiring. Dash Disassembly...... 4.0 • A) Radio housing • B) Faceplate Continue to installation instructions for ALL • C) Radio support • D) Mounting bracket Kit Assembly VEHICLES, Section 4 • E) (2) Pal nuts • F) Shaft supports – 2-shaft radio provision...... 4.1 A B – DIN radio provision...... 4.1

Dash Disassembly D E 1. Remove (2) Phillips screws from the bottom edge of the glove box door and remove the door. C 2. Remove (3) Phillips screws from the lower steering column panel.

4.0 ®

99-7891

Kit Assembly

2-shaft radio provision: 4. Locate the factory wiring harness and connector in the dash and complete all 1. Snap the faceplate* and shaft supports into the radio housing. (Figure A) necessary connections to the radio. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation. Continue to Step 2 5. 2-shaft radio provision (Figure E): DIN radio provision: a. Snap the completed assembly into the sub-dash. Ensure that the radio 1. Position the radio housing in the radio opening by inserting the locating pins on engages the radio support in the dash. the right side of the housing into the holes on the left side of the factory pocket. 6. DIN radio provision (Figure F): (Figure B) a. Remove the metal DIN sleeve from the aftermarket radio. Continue to Step 2 b. Slide the sleeve into the radio housing and secure by bending the metal Insert the radio support into the mounting bracket. Turn the radio support to lock 2. locking tabs down. into place. (Figure C) c. Slide the radio into the sleeve until it clicks in. Ensure that the radio engages 3. Secure the assembly to the factory mounting plate in the sub-dash with (2) pal the radio support in the dash. nuts supplied. (Figure D)

Optional

(Figure A) (Figure B) (Figure C) (Figure D) (Figure E) (Figure F) 4.1 ®

99-7892

Section 5 E Dash Disassembly Acura/Honda/Isuzu Acura CL 1997-1999 1997-2001 TOOLS REQUIRED 1. Unclip the radio trim bezel and disconnect the 99-7892 • Phillips screwdriver • Cutting tool • Socket wrench clock and climate control wiring. (Figure A) KIT FEATURES 2. Remove (2) 8mm hex-head screws securing the Table of Contents factory radio and disconnect the wiring. • 2-shaft radio provision with pocket Dash Disassembly • DIN radio provision with pocket Continue on the next page • ISO DIN radio provision with pocket Acura • Rear support provision – CL 1997-1999...... 5.1 – Integra 1990-1993...... 5.1 KIT COMPONENTS – Integra 1994-2001...... 5.2 • A) Radio housing • B) Faceplate – Legend 1990...... 5.2-5.3 • C) ISO DIN brackets • D) Rear support bracket – Legend 1991-1996...... 5.3 • E) (2) Phillips screws – TL 1996-1998...... 5.4 – Vigor 1992-1994...... 5.4 A B Honda – Accord 1990-1993...... 5.5 – Accord 1994-1997...... 5.5 – Odyssey 1995-1998...... 5.6 – Isuzu Oasis 1996-1999...... 5.6 C D Kit Assembly – 2-shaft radio provision with pocket...... 5.6 – DIN radio provision with pocket...... 5.7 – ISO DIN radio provision with pocket...... 5.7 (Figure A) 5.0 ®

99-7892

Dash Disassembly

Acura CL 1997-1999 (Cont) Acura Integra 1990-1993 3. Cut and remove the side clips from the radio 1. Remove (3) screws from each side of the center housing. (Figure B) console and remove the console. (Figure A) 4. Secure the rear support bracket to the back of the pocket with (2) Phillips screws supplied. (Figure C) 2. Remove (2) screws securing the factory radio to the sub-dash support bracket. (Figure A) Continue to kit assembly for ALL VEHICLES, Section 5 3. Slide the radio/pocket assembly out and disconnect the wiring. 4. Cut and remove the top clips from the radio housing. (Figure B) (Figure A) For ISO DIN radio provisions: Secure the rear (Figure B) support bracket to the back of the pocket with (2) Phillips screws supplied. (Figure C) Continue to kit assembly for ALL VEHICLES, Section 5

(Figure C) (Figure B) (Figure C) 5.1 ®

99-7892

Dash Disassembly

Acura Integra 1994-2001 Acura Legend 1990 1. Remove the cover cap located under the 1. Remove (2) screws below the ashtray. (Figure A) emergency brake and remove (2) screws exposed. Unclip the dash trim bezel. (Figure A) 2. 2. Remove (2) screws from the rear corners of the 3. Disconnect the cigarette lighter wiring and remove the bezel. lower dash trim bezel and remove. (Figure A) 4. Remove (2) bolts securing the rear of the factory 3. Remove the ashtray and (2) screws exposed. radio and disconnect the wiring. Unsnap the ashtray housing and disconnect the (Figure A) cigarette lighter harness. Continue on the next page 4. Remove the gear shifter knob and unsnap the shifter trim. 5. Remove (2) screws below the radio opening and remove the upper dash trim bezel.

6. Remove (2) 8mm screws securing the factory radio (Figure B) and disconnect the wiring. 7. Cut and remove the top clips from the radio housing. (Figure B) For ISO DIN radio provisions: Secure the rear support bracket to the back of the pocket with (2) Phillips screws supplied. (Figure C) Continue to kit assembly for ALL VEHICLES, Section 5 (Figure C) (Figure A) 5.2 ®

99-7892

Dash Disassembly

Acura Legend 1990 (Cont) Acura Legend 1991-1996 5. Cut and remove the top clips from the radio 1. Remove (2) screws below the ashtray. Unclip the housing. (Figure B) dash trim bezel. (Figure A) 6. Modify the factory radio housing by trimming the shaded portions of the housing lip. (Figure C) 2. Disconnect the cigarette lighter wiring and remove the bezel. Continue to kit assembly for ALL VEHICLES, Section 5 3. Remove (2) bolts securing the rear of the factory radio and disconnect the wiring. 4. Cut and remove the top clips from the radio housing. (Figure B) (Figure A) For ISO DIN radio provisions: Secure the rear (Figure B) support bracket to the back of the pocket with (2) Phillips screws supplied. (Figure C) ¼” ¼” Continue to kit assembly for ALL VEHICLES, Section 5 ¾” ¾” Factory radio housing opening 1¼” 1” 1” 1¼”

(Figure C) (Figure B) (Figure C) 5.3 ®

99-7892

Dash Disassembly

Acura TL 1996-1998 Acura Vigor 1992-1994 1. Using a small screwdriver, unclip the 1. Remove the access cap from the climate perimeter of the radio trim bezel. control cluster and (1) screw exposed. (Figure A) 2. Disconnect the climate control and rear defroster wiring and remove 2. Unclip the cluster and remove (2) screws the bezel. exposed. Remove the ashtray and (2) Phillips screws exposed. (Figure A) 3. Remove (4) Phillips screws 3. Remove the cover caps from each front securing the factory radio/trim (Figure A) corner of the center console and the (Figure A) bezel assembly. (Figure A) screws exposed. 4. Loosen (2) Phillips screws securing 4. Open the storage compartment, lift up the the back of the radio to the metal carpet and remove (2) screws exposed. housing and slide the unit out. Disconnect the wiring. 5. Lift up on the center console and remove. Unclip the radio trim bezel and Note: it is NOT necessary to disconnect the wiring. remove the screws securing the metal housing to the bezel. (Figure B) 6. Remove (2) bolts from the back (Figure B) of the factory radio and disconnect the 5. Cut and remove the top clips from wiring. ¼” ¼” the radio housing. (Figure B) 7. Cut and remove the top clips from the ¾” ¾” For ISO DIN radio provisions: radio housing. (Figure B) Factory radio Secure the rear support bracket 8. Modify the factory radio housing by housing opening to the back of the pocket with (2) trimming the shaded portions of the Phillips screws supplied. (Figure C) housing lip. (Figure C) 1¼” 1” 1” 1¼” Continue to kit assembly for Continue to kit assembly for ALL VEHICLES, Section 5 (Figure C) ALL VEHICLES, Section 5 (Figure C) 5.4 ®

99-7892

Dash Disassembly

Honda Accord 1990-1993 Honda Accord 1994-1997 1. Remove (4) screws from the 1. Remove the ashtray and (1) 3/4” #8 Phillips screw lower portion of the center exposed. console. (Figure A) 2. Open the storage compartment and remove (2) #8 Phillips screws exposed. 2. Remove the gear shifter knob and lift the console 3. Remove the cupholder tray and (3) #8 Phillips screws inside. (Figure A) out. Remove the ashtray and ashtray bracket. 4. Lift the center console out and remove (2) Phillips (Figure A) screws exposed at the base of the dash trim bezel. (Figure B) 3. Remove (2) screws from (Figure B) the bottom of the radio 5. Unclip the bezel and remove. Remove (2) hex-head support, slide the unit out and screws ecuring the factory radio and disconnect the disconnect the wiring. wiring. 4. Cut and remove the top clips 6. Cut and remove the side clips from the radio from the radio housing. housing. (Figure C) (Figure B) (Figure B) 7. Secure the rear support bracket to the back of the (Figure C) pocket with (2) For ISO DIN radio provisions: Phillips screws Secure the rear support supplied. bracket to the back of the (Figure D) pocket with (2) Phillips screws Continue to kit supplied. (Figure C) assembly for Continue to kit assembly for ALL VEHICLES, ALL VEHICLES, Section 5 Section 5 (Figure C) (Figure A) (Figure D) 5.5 ®

99-7892

Dash Disassembly Kit Assembly

Honda Odyssey 1995-1998, All Vehicles Isuzu Oasis 1996-1999 2-shaft radio provision with pocket: 1. Remove (2) 8mm screws under the glove box. 1. Snap the faceplate into the radio housing. (Figure A) 2. Remove (1) Phillips screw on the glove box arm and remove the box. 2 Slide the radio into the kit and secure with shaft nuts. (Figure A) 3. Remove (2) Phillips screws exposed in the glove box cavity. Continue on the next page, Step 4 (Figure A) 4. Remove (2) Phillips screws below the storage box door (under the ashtray). 5. Remove (2) screws from the left side of the dash console. Remove (1) Phillips screw from the coin tray. 6. Remove (1) Phillips screw under the ignition. Remove (4) Phillips screws securing the factory cupholder. (Figure B) 7. Remove (2) 8mm hex-head screws from the rear support bracket and disconnect the wiring. 8. Cut and remove the top clips from the radio housing. For ISO DIN radio provisions: Secure the rear support bracket to the back of the pocket with (2) Phillips screws supplied. (Figure C) Continue to kit assembly for ALL VEHICLES, Section 5 (Figure C) (Figure C) 5.6 ®

99-7892 Kit Assembly (Cont)

DIN radio provision with pocket: All vehicles (CONT): 1. Remove the metal DIN sleeve from 4. Locate the factory wiring harness the aftermarket radio. and connector in the dash and complete all necessary 2. Slide the sleeve into the kit and connections to the radio. Metra secure by bending the metal recommends using the proper locking tabs down. (Figure B) mating adapter from Metra. Test 3. Slide the radio into the sleeve until the radio for proper operation. it clicks in. (Figure B) 5. Accord 1990-93, Integra, Continue to Step 4 Odyssey, Oasis: Snap the completed assembly into ISO DIN radio provision with pocket: (Figure B) the sub-dash. (Figure D) 1. Slide the ISO DIN brackets onto the Legend, TL, Vigor: sides of the rear support bracket. Snap the completed assembly Cut and remove the shaft supports into the factory trim bezel. Secure from the Faceplate and snap into the bezel to the dash with those the radio housing. (Figure C) screws previously removed. 2. Remove the metal DIN sleeve and (Figure D) trim ring from the aftermarket radio. Accord 1994-97, CL: 3. Slide the radio into the housing; Slide the completed assembly into align the holes in the radio with the the sub-dash and secure the rear holes in the ISO DIN brackets and support bracket to the rear support secure with the screws supplied provision with (2) hex-head bolts with the radio. (Figure C) previously removed. (Figure E) Continue to Step 4 (Figure C) (Figure E) 5.7 ®

99-7893

Section 6 Table of Contents Dash Disassembly (Cont)

Honda CR-V / Prelude Dash Disassembly remove the (4) outer screws exposed. Unclip the 1997-2001 center console and remove. – Honda CR-V 1997-2001...... 6.0 99-7893 – Honda Prelude 1997-2001...... 6.1 6. Remove (2) Phillips screws securing the radio trim bezel, disconnect the wiring, and remove the trim Kit Assembly bezel/radio assembly. (Figure A) KIT FEATURES – 2-shaft radio provision with pocket...... 6.1-6.2 • DIN radio provision with pocket 7. Remove (4) Phillips screws securing the radio to • 2-shaft radio provision with pocket – DIN radio provision with pocket...... 6.1-6.2 the bezel and remove. 8. Cut and remove all mounting clips on the radio Dash Disassembly housing EXCEPT the clips stamped “C”. (Figure B) KIT COMPONENTS Continue to kit assembly for • A) Radio housing Honda CR-V 1997-2001 ALL VEHICLES, Section 6 A 1. Open the glove box, squeeze the retaining clips and remove the stoppers. “C” 2. Lower the glove box and remove (2) Phillips screws from the left edge. 3. Remove (2) Phillips screws from the lower steering column panel and remove.

TOOLS REQUIRED 4. Unclip the lower console cover (below the ashtray and pocket) and remove. “C” • Phillips screwdriver • Cutting tool • Socket wrench 5. Remove (2) Phillips screws from the base of the center console, open the console pocket and (Figure A) (Figure B) 6.0 ®

99-7893

Dash Disassembly Kit Assembly

Honda Prelude 1997-2001 All Vehicles 1. Using a panel removal tool, unclip the radio trim bezel and 2-shaft radio provision with pocket: remove (some force may be required). (Figure A) 1. Slide the radio into the radio housing. (Figure A) 2. Remove (4) Phillips screws securing the factory radio/ bracket housing assembly and disconnect the wiring. 2. Secure unit with shaft nuts. (Figure A) 3. Remove (4) Phillips screws securing the factory radio to the Continue to Step 4 bracket housing and remove. DIN radio provision with pocket: 4. Cut and remove all mounting clips on the radio housing EXCEPT the clips stamped “P”. (Figure B) 1. Remove the metal DIN sleeve from the aftermarket radio. Continue to kit assembly for ALL VEHICLES, Section 6 2. Cut and remove the shaft supports from the radio (Figure A) housing and then slide the sleeve into the kit. “P” Secure by bending the metal locking tabs down. 3. Slide the radio into the sleeve until it clicks in. (Figure B) Continue to Step 4

4. Locate the factory wiring harness and connector in the dash and complete all necessary connections to “P” the radio. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation.

(Figure A) (Figure B) Continued on the next page (Figure B) 6.1 ®

99-7893

Kit Assembly (Cont) Notes All Vehicles (CONT) 5. Install the completed assembly to the vehicle. CR-V: Snap the completed assembly into the radio trim bezel and secure the bezel to the dash using those screws previously removed. (Figure C) Prelude: (Figure C) Snap the completed assembly into the factory bracket housing and secure the housing to the sub-dash with (4) Phillips screws previously removed. (Figure D)

(Figure D) 6.2 ®

99-7894

Section 7 Table of Contents

Honda Accord Dash Disassembly...... 7.0-7.1 1998-2002 Kit Assembly 99-7894 – DIN radio provision...... 7.1-7.2

KIT FEATURES • DIN radio provision • Equalizer/factory-pocket provision Dash Disassembly

KIT COMPONENTS 1. Unsnap the clock panel, disconnect the wiring and remove. • A) Radio housing • B) Brackets (Figure A) • C) Equalizer dummy plate 2. Remove (1) Phillips screw exposed in the clock cavity. (Figure A) A B 3. Remove (2) Phillips screws below the factory radio. Unclip the radio trim bezel and disconnect the wiring. (Figure A) 4. Remove (4) Phillips screws securing the factory C radio assembly and disconnect the wiring. 5. Remove (2) screws securing the factory pocket to the assembly. 6. Snap the Brackets onto the front of the lower TOOLS REQUIRED mounting tabs on the radio housing. (Figure B) • Phillips screwdriver • Cutting tool • Socket wrench Continue on the next page (Figure B) 7. 0 ®

99-7894

Dash Disassembly (Cont) Kit Assembly

7. If NOT KEEPING the factory pocket: DIN radio provision: If an equalizer will be included: “A” 1. Remove the metal DIN sleeve from Slide the unit into the back of the the aftermarket radio. radio housing and secure. 2. Slide the sleeve into the radio housing and secure by bending the metal If an equalizer will not be locking tabs down. included: Snap the equalizer 3. Slide the radio into the sleeve until dummy plate into the opening. it clicks in. (Figure A) Continue to kit assembly 4. Locate the factory wiring harness and If KEEPING the factory pocket: connector in the dash and complete Cut sections “A” on the back all necessary connections to the radio. Metra recommends using the of the radio housing and break (Figure C) proper mating adapter from Metra. (Figure A) away the bottom portion of the Test the radio for proper operation. housing. (Figure C) 5. Secure the completed assembly to Secure the factory pocket to the sub-dash with (4) Phillips screws previously removed. (Figure B) the housing with (2) screws “A” previously removed. (Figure D) 6. Re-attach the radio trim bezel. Be sure the clips on the back of the Continue to kit assembly bezel engage slots “A” on the kit. (Figure B)

(Figure D) (Figure B) 7.1 ®

99-7895

Section 8 Table of Contents Dash Disassembly

Honda Accord Dash Disassembly...... 8.0 1. Unsnap the clock panel, disconnect the wiring and remove. 1998-2002 Kit Assembly 2. Remove (1) Phillips screw exposed in the clock cavity. 99-7895 – DIN radio provision with pocket...... 8.1 (Figure A) 3. Remove (2) Phillips screws below the factory radio. Unclip KIT FEATURES the radio trim bezel and disconnect the wiring. (Figure A) • DIN radio provision with pocket 4. Remove (4) Phillips screws securing the factory radio assembly and disconnect the wiring. KIT COMPONENTS Continue to kit assembly • A) Radio housing A

TOOLS REQUIRED • Phillips screwdriver

(Figure A)

8.0 ®

99-7895

Kit Assembly

DIN radio provision with pocket: 1. Remove the metal DIN sleeve from the aftermarket radio. 2. Slide the sleeve into the radio housing and secure by bending the metal locking tabs down. 3. Slide the radio into the sleeve until it clicks in. (Figure A) 4. Locate the factory wiring harness and antenna connector in the dash. (Figure A) (Figure B) (Figure C) Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation. 5. Secure the completed assembly to the sub-dash with (4) Phillips screws previously removed. (Figure B) 6. Re-attach the radio trim bezel. (Figure C) Note: Make sure the clips on the back of the bezel engage the slots on the kit.

8.1 ®

Notes ®

Notes ®

Notes ®

Notes ®

Installation instructions for part INST-7800

IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians REV. 10/12/2016 INST-7800 REV.

METRA - The World’s best kits ® metraonline.com © COPYRIGHT 2016 METRA ELECTRONICS CORPORATION