SmartLine Wireless Absolute Pressure Transmitter Specification 34-SW-03-02, August 2019
Model:
STAW84L 0 to 500 psia 0 to 35 barA
Introduction
SmartLine Wireless Pressure continues the evolution of
Honeywell’s wireless transmitter product offering and provides the latest critical advancements to support industrial automation users’ desire to expand wireless use for monitoring and control. With over 14 years of industrial wireless experience, the SmartLine Wireless Pressure builds upon and is compatible with the current XYR 6000 product porfotlio.
Similar to the XYR 6000 wireless transmitter, the SmartLine Wireless product line is part of the
Honeywell OneWireless™ system and is ISA100 - Figure 1 — SmartLine Wireless In-Line Absolute ready. Pressure Transmitter
SmartLine Wireless Pressure transmitters also The previous generation transmitters primarily were leverage SmartLine technology in the incorporaton of applied to monitoring applicaions but experienced users the enhanced SmartLine Pressure meter body. By know that Honeywell’s wireless products are as reliable, utilizing the same meter body as in the non-wireless secure, and safe as their wired counterparts. With this pressure product offering, you get best-in-class knowledge, users are now looking for wireless performance, reduction in spares inventory, and a transmiiters for use in specific control applications. lessening of the maintenance learning curve. SmartLine Wireless introduces a step change in The SmartLine Wireless Pressure transmitter enables performance and most notably, performance suitable for customers to obtain data and create information from control. SmartLine Wireless performance is improved in remote and hazardous measurement locations without these ways: the need to run wires, where running wire is cost Fast ½ second publication rate prohibitive and/or the measurement is in a hazardous location. Without wires, transmitters can be installed Built-in additional noise reduction and operational in minutes, quickly providing More powerful 4 dBi integral antenna information back to your system. Good battery life performance even at ½ second publication rate.
2 SmartLine Wireless Transmitter
SmartLine Wireless Pressure retains the following SmartLine Wireless Features desirable features from the XYR 6000 product offering: Local and over-the-air provisioning capability. All Mesh or non-mesh configuration within each Honeywell wireless devices feature a secure method to transmitter join the local wireless network, also known as provisioning. Generic, off-the-shelf lithium ion battery. SmartLine Wireless transmitters feature two methods to provision a transmitter onto the network which are either Two “D” size batteries for longer life. by using a handheld device to locally communicate Choice of over-the-air or local provisioning through the IR interface or remotely using the over-the-air (network security join key) function. The over-the-air function is managed by the OneWireless gateway, Wireless Device Manager (WDM). Over-the-air firmware upgrade capability In either method, the communication of secure, unique Unique, encrypted provisionng key delivered from the factory provisioning keys is one of the main factors to prevent against unintended access. Honeywell’s security keys are Remote and integral antenna options unique for each device from the factory, never made 24 VDC power option visible, always encrypted, and uniquely generated from the gateway that manages the deployed network. Publication rates of 1, 5, 10, or 30 seconds, plus new selections for ½ sec, and 1, 15, 30, Over-the-air firmware updates. Once joined as a 60 minutes member of your OneWireless network, the WDM can Transmitter range (integral antenna) of 1150’ download new transmitter firmware releases to each (350 m) under ideal conditions. SmartLine Wireless transmitter over the wireless network. Locating and accessing the transmitter locally is not The STAW84L is a high performance absolute required thus saving time and keeping your personnel in pressure transmitter featuring piezoresistive sensor safe environments. technology which combines pressure sensing with on-chip temperature compensation capabilities. The Mesh and non-mesh capability. All SmartLine Wireless result is high accuracy, stability and performance over transmitters can be configured to operate in either a mesh a wide range of application pressures and network or a star (non-mesh) network. The configuration temperatures. is specific to each wireless transmitter and thus the network can consist of a mixture of meshing and non- The SmartLine family is also fully tested and meshing devices. Non-meshing is desirable for compliant with Experion® PKS providing the highest deterministic communications which is preferred for level of compatibility assurance and integration control. capabilities. SmartLine easily meets the most Transmission power setting. To comply with local and demanding application needs for pressure regional requirements, SmartLine Wireless transmitters are measurement applications. set at the factory to the maximum transmission power setting allowed for the country of use. Span & Range Limits: Non-proprietary battery. Sourcing lithium thionyl chloride Model URL LRL Max Span Min Span batteries is much simpler since SmartLine Wireless utilizes psia psia psia psia commercial off-the-shelf batteries. Please see the list of (barA) (barA) (barA) (barA)) approved battery manufacturers later in this specification. STAW84L 500 (35) 0 (0) 500 (35) 5 (0.35) Batteries are housed in an IS-approved battery compartment making battery changes safe and easy. Backward compatibility. SmartLine Wireless transmitters can join existing OneWireless networks and interoperate with existing XYR 6000 wireless transmitters or other ISA100 Wireless compliant transmitters or networks.
SmartLine Wireless Transmitter 3
OneWireless Network Features The core of the Honeywell wireless solution is the OneWireless Network which consists a gateway, access point(s), and field routers. The Wireless Device Manager (WDM) serves as the gateway function and in this role, manages the communication from the wireless field devices to the process control application. Typically, the WDM connects logically to the process control network (Level 2 or wireless DMZ). As the wireless network manager, the WDM provides easy access to the entire wireless network through a browser-based user interface. The Honeywell WDM can manage devices communicating over the ISA100 Wireless protocol and the Wireless HART protocol. The ability to deploy redundant WDMs improves the reliability ensuring no loss of process data which is a requirement for control applications. The Field Device Access Point (FDAP) serves in two roles in the OneWireless network infrastructure, which are: 1) access point, and 2) field router. As an access point, the FDAP directly connects to the WDM via Ethernet LAN cable. More than one access point is permitted and, when more than one is present, it ensures dual path for communications into the WDM from the field devices. As a field router, the FDAP located in the field would communicate to the FDAP acting as an access point. Using the FDAP as a router is more efficient than using field devices as routers since FDAPs are line powered devices whereas field devices are typically battery powered, and the FDAP offers greater range. The meshing capability of FDAPs allows flexibility in the setup of the wireless network to fit the requirements for wireless network performance, in terms of reliable communications, performance, and future growth. The choice of non-meshing network may be desirable for decreased communication latency which a FDAP serving as a field router helps ensures.
Wireless Specifications
Parameter Description Wireless 2,400 to 2,483.5 MHz (2.4 GHz) Industrial, Scientific and Medical (ISM) band Communication DSSS - Direct Sequential Spread Spectrum per FCC 15.247 / IEEE 802.15.4 2006 Every data packet transmitted in either direction is verified (CRC check) and acknowledged by the receiving device. USA – FCC Certified Canada – IC Certified European Union – Radio Equipment Directive compliant DSSS RF Transmitter NA Selection –100 mW (20.0 dBm) maximum EIRP including antenna for USA and Canadian Power locations. EU Selection – 63 mW (18.0 dBm) maximum EIRP including antenna per RTTE/ETSI for EU locations. Compliant to ETSI EN 300 328 wireless standard Data PV Publish Cycle Time: Configurable as 0.5, 1, 5, 10, 30 seconds, plus 1, 15, 30, 60 minutes Rate: 250 Kbps Antennas Integral – 4 dBi omnidirectional monopole (default selection) Remote – 8 dBi omnidirectional monopole with up to 10 m cables and lightning surge arrester Remote – 14 dBi directional parabolic with up to 10 m cables and lightning surge arrester. Signal Range Nominal 350 m (1150 feet) between Field Transmitter and Infrastructure Unit (FDAP) when using 4 dBi Integral antenna with a clear line of sight* *Actual range will vary depending on antennas, cables and site topography.
4 SmartLine Wireless Transmitter
Specifications
Operating Conditions – All Models
Parameter Reference Rated Condition Operative Limits Transportation Condition and Storage (at zero static) °C °F °C °F °C °F °C °F
Ambient Temperature4 25 ±1 77 ±2 -40 to 85 -40 to 185 -40 to 85 -40 to 185 -55 to 120 -67 to 248 Ambient Temperature 25 ±1 77 ±2 -40 to 85 -40 to 185 LCD Display visible range Meter Body Temperature 25 ±1 77 ±2 -40 to 1101 -40 to 230 -40 to 125 -40 to 257 -55 to 120 -67 to 248 Humidity %RH 10 to 55 0 to 100 0 to 100 0 to 100
Vacuum Region - Minimum See Figure 2. Pressure Operate within specifications above 25 mmHgA (33 mbarA). Short term1 exposure to full vacuum will not result in damage
Maximum Allowable Working Standard: Pressure (MAWP) 2,3 STAW84L = 500 psia, 35 barA
Vibration Maximum of 4g over 15 to 200Hz. Shock Maximum of 40g. Commercially available, non-proprietary 3.6V Lithium thionyl chloride (LiSOCl2) batteries, non-rechargeable, size D. Battery pack-only option is available. Approved list of the manufacturer models: 1. Xeno Energy XL-205F Power 2. Eagle Picher PT-2300H 3. Tadiran TL-5930/s 24 VDC power option. For Non I.S. application: 16 to 28 VDC input range, max input current 100mA. For I.S. application: Barrier in accordance with the control drawing required, entity parameters 30V, 120mA, 0.9W 1Short term equals 2 hours at 70°C (158°F) 2 Units can withstand overpressure of 1.5 x MAWP without damage 3 Consult factory for MAWP of SmartLine Wireless transmitters with CRN approval 4 The Ambient Limits shown are for Ordinary Non-Hazardous locations only. Refer to the Hazardous Locations Approvals section for the Ambient Limits when installed in Hazardous Locations.
SmartLine Wireless Transmitter 5
Remote Antenna Cables
Remote Antennas
8 dBi Omnidirectional Antenna 14 dBi Directional Antenna
6 SmartLine Wireless Transmitter
Performance Specifications
Performance under Rated Conditions* - Model STAW84L (0 to 500 psia/35 barA)
Parameter Description Upper Range Limit psia 500 barA 35 Minimum Span psia 5 barA 0.35 Zero Suppression No limit except minimum span within 0 (zero) to +100% URL. Accuracy (Reference – Includes ±0.065% of calibrated span or upper range value (URV), whichever is greater, combined effects of linearity, terminal based. hysteresis, and repeatability) • Accuracy includes residual error For URV below reference point (20 psia), accuracy equals: after averaging successive readings. 20 psia 1.4 barA 0.0125 0.05 or 0.0125 0.05 in % of span span/ psia span/ barA Zero Temperature Effect per 28°C ±0.05% of span. (50°F) For URV below reference point (75 psia), effect equals:
75 psia 5.25 barA ±0.05 ( span/ psia) or ±0.05 ( span/ barA) in % of span Combined Zero and Span ±0.075% of span. Temperature Effect per 28°C For URV below reference point (75 psia), effect equals: (50°F) 75 psia 5.25 barA ±0.025 + 0.05 ( span/ psia) or ±0.025 + 0.05 ( span/ barA) in % of span * Performance specifications are based on reference conditions of 25°C (77°F), 10 to 55% RH, and 316L Stainless Steel barrier diaphragm.
Performance Under Rated Conditions – All Models Parameter Description Electromagnetic Compatibility IEC 61326-1 Lightning Surge Arrester (Remote Frequency range: 0 – 3 GHz, 50 Ohms, VSWR = 1:1.3 Max, Insertion Loss = 0.4 dB antenna only) Connectors Type N Female, Max, Gas Tube Element: 90 V ± 20%, Impulse Breakdown Voltage = 1,000 V ± 20%, Maximum Withstand Current = 5 KA. CE Conformity These transmitters are in conformity with the Radio Equipment Directive, ETSI EN 300 328 V2.1.1 including EMC standard EN61326-1 2013
SmartLine Wireless Transmitter 7
Physical Specifications Parameter Description Mounting Bracket Carbon Steel (zinc-plated) or Stainless Steel angle bracket or flat bracket available. Fill Fluid Silicone DC 200 oil, or CTFE (Chlorotrifluoroethylene) Electronic Housing Epoxy-Polyester hybrid paint. Low Copper-Aluminum with 1/2” NPT or M20 conduit connections. Meets NEMA 4X (hosedown and corrosion resistant), IP 66/67 (hosedown and submersible to 1m).
Stainless Steel Housing (option) 316 SS or Grade CF8M, the casting equivalent of 316 SS with M20 or 1/2" NPT conduit connections. If ordered with the Remote Antenna options, the antenna parts are not SS or Marine type cables; the integral antenna uses SS parts. Process Connections 1/4-inch NPT; 1/2-inch NPT with adapter. Process heads meet DIN 19213 requirements. Mounting Can be mounted in virtually any position using the standard mounting bracket. Mounting should result in the antenna being vertically oriented. Bracket is designed to mount on 2- inch (50 mm) vertical or horizontal pipe. See Figure 2. Dimensions See Figure 3, Figure 4 and Figure 5. Net Weight Approximately 11 pounds (5 Kg) 1 1 Add 8.0 pounds (3.6 kg) to any model equipped with stainless steel housing option (Model Selection Guide Table IV selection M or N)
Materials Specifications (see model selection guide for availability/restrictions with various models) Parameter Description Barrier Diaphragms Material 316L SS and Hastelloy® C-2762
Process Head Material 316 SS3
Vent/Drain Valves & Plugs 1 316 SS3 Head Gaskets N/A Meter Body Bolting N/A 1 Vent/Drains are sealed with Teflon® 2 Hastelloy C-276 or UNS N10276 3 Supplied as 316 SS or as Grade CF8M,the casting equivalent of 316 SS.
8 SmartLine Wireless Transmitter
Mounting and Dimensions
Reference Dimensions:
Figure 2 — Examples of typical mounting positions (antenna omitted)
Figure 3 – In-Line, Informational and dimensional drawing (4 dBi antenna shown)
SmartLine Wireless Transmitter 9
Figure 4 — Typical mounting dimensions for STAW84L (remote antenna adaptor shown)
Figure 5 — Typical mounting dimensions for STAW84L (4 dBi antenna shown)
10 SmartLine Wireless Transmitter
Hazardous Locations Approvals Refer to control drawing 50136123, in the User’s manual #34-SW-25-01, for intrinsically safe installation details
AGENCY TYPE OF PROTECTION Ambient Product Temperature Applicability Intrinsically Safe: Pressure Class I; Division 1; Groups A, B, C, D; Class II, Division 1, Groups E, F, G; Class III, Division 1; T4 See tables below Class I, Zone 0 AEx ia IIC T4 Ga Class I Zone 2 AEx ic IIC T4 Gc Ex ia IIC T4 Ga Ex ic IIC T4 Gc Non Incendive: Pressure Class I; Division 2; Groups A, B, C, D; Class II, Division 2, Groups E, F, G; See tables below Class III, Division 2, T6...T4 Ex nA [ia Ga] IIC T6...T4 Gc Class I, Zn 2, AEx nA [ia Ga] IIC T6...T4 Gc Explosion-Proof/ Flameproof/Dust Proof: Pressure CSA Class I, Division 1; Groups A, B, C, D; Class II, Division 1, Groups E, F, G; (USA and Class III, Division 1; T6...T4 See tables below Canada) Ex db [ia Ga] IIC T6...T4 Gb Ex tb [ia Da] IIIC T95...T125 Db Class I, Zn 1 AEx db [ia Ga] IIC T6...T4 Gb Class II, Zn 21, AEx tb [ia Da] IIIC T95...T125 Db Enclosure: Type 4X/ IP66/ IP67 Standards Used: CSA C22.2 No. 0-10 CSA C22.2 No.25-17 CSA C22.2 No.30-M1986 CSA C22.2 No.94.2-15 CAN/CSA C22.2 No.61010-1-12 CAN/CSA C22.2 No.157-92 CSA C22.2 No.213-16 CAN/CSA C22.2 No.60529:16 CAN/CSA C22.2 No.60079-0:15 CAN/CSA C22.2 No.60079-1:16 CAN/CSA C22.2 No.60079-11:14 CAN/CSA C22.2 No.60079-15:16 CAN/CSA C22.2 No.60079-31:15 ANSI/ISA 12.12.01-2015 ANSI/UL 60079-0-2013 ANSI/UL 60079-1-2015 ANSI/UL 60079-11-2014 ANSI/UL 60079-15-2013 ANSI/UL 60079-31-2015 FM 3600 – Dec 2011 FM 3615 – Aug 2006 FM 3616 – Dec 2011 ANSI/IEC 60529 – 2004 ANSI/UL 913-2015 ANSI/UL 50E-2015 ANSI/UL 61010-1-2016
AGENCY TYPE OF PROTECTION Ambient Temperature Product Applicability Intrinsically Safe: Pressure IS Class I, II, III; Division 1; Groups ABCDEFG; T4 -40 oC to +85 °C Class I, Zone 0 AEx ia IIC Ga T4 Class I, Zone 2[0] AEx ic [ia Ga] IIC Gc T4 Non Incendive: -40 °C to +85 °C : T5 Pressure NI-AIS Class I; DIV 2; Groups ABCD; T5...T6 -40 °C to +70 °C : T6 Class I, Zone 2[0] AEx nA [ia Ga] IIC Gc; T5...T6 FM Dust Proof: -40 °C to +85 °C : T5, T95 Pressure ApprovalsTM DIP-AIS Class II, III DIV 1; Groups EFG; T5...T6 -40 °C to +70 °C : T6 (USA) Zone 21[20] AEx tb [ia Da] IIIC T95°C Db Enclosure: Type 4X/ IP66/ IP67 Standards Used: FM 3600:2018 FM 3610: 2018 FM 3611: 2018 ANSI/ISA 60079-0: 2013 FM 3810: 2018 FM 3616: 2011 ANSI/ ISA 60079-15: 2013 ANSI/ ISA 60079-31: 2015 ANSI/ ISA 60079-11: 2014 ANSI/ NEMA 250: 2008 ANSI/ ISA 60529: 2004
SmartLine Wireless Transmitter 11
AGENCY TYPE OF PROTECTION Ambient Product Temperature Applicability Intrinsically Safe: Pressure II 1 G Ex ia IIC T4 Ga See tables below II 3 G Ex ic IIC T4 Gc Flameproof / Dust Proof: Pressure II 2[1] G Ex db [ia Ga] IIC T6...T4 Gb See tables below II 2[1] D Ex tb [ia Da] IIIC T95C...T125C Db ATEX Non Incendive: Pressure See tables below II 3[1] G Ex ec [ia Ga] IIC T6...T4 Gc Enclosure: IP66/ IP67 Standards Used: EN 60079-0 : 2012 + A1 EN 60079-1 : 2014 EN 60079-11 : 2012 EN 60079-26 : 2006 EN 60079-7 : 2015 IEC 60079-31 : 2013
AGENCY TYPE OF PROTECTION Ambient Product Temperature Applicability*
Intrinsically Safe: Pressure Ex ia IIC T4 Ga See tables below Ex ic IIC T4 Gc Flameproof / Dust Proof: Pressure Ex db [ia Ga] IIC T6...T4 Gb See tables below Ex tb [ia Da] IIIC T95C...T125C Db IECEx Non Incendive: Pressure See tables below Ex ec [ia Ga] IIC T6..T4 Gc Enclosure: IP66 /IP67 Standards Used: IEC 60079-0 : 2011 IEC 60079-1 : 2014 IEC 60079-11 : 2011 IEC 60079-26 : 2006 IEC 60079-7 : 2015 IEC 60079-31 : 2013
For Intrinsic Safety Installations: The applicable temperature class, ambient temperature (Ta) and process temperature (Tp) range of the equipment when installed with type protection “Ex ia” is as follows: Protection Type Temperature Class T4 Ex ia Ta = -40 to 80°C Tp = -40 to 125°C Ex ic Ta = -40 to 85°C Tp = -40 to 125°C
For Flameproof , Dustproof, increased safety and non incendive Installations: The applicable temperature class, ambient temperature (Ta) and process temperature (Tp) range of the equipment when installed with type protection “Ex db”, “Ex ec”, “Ex nA” is as follows: Protection Type Temperature Class T4 T5 T6 Ex db Ta = -40 to 85°C Ta = -40 to 85°C Ta = -40 to 75°C Ex ec Tp = -40 to 125°C Tp = -40 to 100°C Tp = -40 to 85°C Ex nA The applicable temperature class, ambient temperature (Ta) and process temperature (Tp) range of the equipment when installed with type protection “Ex tb” is as follows: Protection Type Temperature Class T125C T95C Ex tb Ta = -40 to 85°C Ta = -40 to 85°C Ex nA Tp = -40 to 125°C Tp = -40 to 100°C Ex ec
12 SmartLine Wireless Transmitter
Transmitter Options (indicated selection code is shown)
ISA100 Wireless Release Selections (A or B) OneWireless R2xx represents the previous releases whereas R3xx is the current release. A OneWireless system with R3xx firmware can host R2xx and R3xx devices. Please select the option to match the targeted OneWireless system.
Remote Antenna and Cables (M or D) The user can select one of the optional remote antennas listed. The selection of the antenna option automatically includes the remote antenna adapter. To complete the option selection, one of the remote antenna cables (1, 2, or 3) must also be selected.
Lightning (Surge) Diverter and Cables (1, 2, or 3) The lightning surge diverter options includes the surge diverter and cable. The diverter features Type N connections (female) on both ends. The remote antenna adapter is not included.
Remote Antenna Adapter (A) This option provides an adapter to be inserted into the opening where the integral antenna normally connects. The adapter is designed to connect to a remote antenna that the user supplies. It features a female Type N connection.
Standard Diagnostics plus Anti-Alias Filter (3) This option enables the Anti-Alias filter option which attenuates the higher frequencies and helps to prevent aliasing components from being sampled.
Destination Country (CA, EU, or US) This selection sets the transmission power at the factory to comply with the installation country location.
Custom Configuration (C) Customer specified configuration parameters are programmed into the transmitter at the factory. Configuration information needs to be communicated to Honeywell Order Management at time of order entry. Additionally, the Honeywell OneWireless user interface is accessible through any browser and thus all configurable parameters are visible and can be edited.
Custom Calibration (B) Custom calibration would input customer specified LRV and URV values, and check linearity. LRV and URV information needs to be communicated to Honeywell Order Management at time of order entry.
Mounting Brackets (1, 3, 5, or 7) The angle mounting bracket is available in either zinc-plated carbon steel or 316 stainless steel and is suitable for horizontal or vertical mounting on a two-inch (50 millimeter) pipe, as well as wall mounting.
An additional flat mounting bracket is also available in carbon steel and 316 stainless steel for two-inch (50 millimeter) pipe mounting.
Tagging (Option 1 or 2) The choice of 1 or 2 stainless steel wired-on tags is available. Each tag can accommodate additional data of up to 4 lines of 28 characters. The number of characters includes spaces. Note that the standard nameplate on the meter body contains the serial number and body-related data.
SmartLine Wireless Transmitter 13
Model Selection Guide Model Selection Guides are subject to change and are inserted into the specifications as guidance only.
Model STAW800 & STAW80L Wireless Absolute Pressure Transmitters Model Selection Guide 34-SW-16-31 Issue 4
Instructions: Make selections from all Tables using column below the proper arrow. Asterisk indicates availability. Letter (a) refers to restrictions highlighted in the restrictions table. Tables delimited w ith dashes.
KEY NUMBER URL/Max Span LRL Min Span Units Selection Absolute 500 (35) 0 (0) 5 (.35) psia (barA) In-Line STAW84L
TABLE I METER BODY SELECTIONS a. Process 1b Head & Process Head/Reference Head Mat'l Barrier Diaphragm Material Diaphragm 316L SS E _ _ _ _ _ * 316 Stainless Steel / 316 Stainless Steel Materials Hastelloy C - 276 F _ _ _ _ _ * Silicone Oil 200 _ 1_ _ _ _ * b. Fill Fluid Fluorinated Oil CTFE _ 2 _ _ _ _ * Size/Type Material 1/2" NPT (female) Same as Process Head 1a _ _ G _ _ _ * c. Process 1/2" NPT (male) Same as Process Head _ _ H _ _ _ * Connection DIN 19213 (1/4" female NPT) Same as Process Head _ _ D _ _ _ * G1/2 B Threaded Fitting Same as Process Head _ _ B _ _ _ * d. Bolt/Nuts _ _ _ 0 _ _ * Materials None e. Vent/Drain Head Type Vent Type Location Vent Material Type/Location None None None None _ _ _ _ 0 _ * f. Gasket None * Materials _ _ _ _ _ 0 1 Except Carbon Steel Heads shall use 316SS Vent/Drain & Plugs 1a STAW822,840 supplied via 1/2" flange adapter same material as process head except carbon steel shall use 316 SS 1b Reference head available only w ith Dual head models. In-line models supplied w ith process head only
14 SmartLine Wireless Transmitter
STAW84L Availability TABLE II Meter Body & Connection Orientation Head/Connect 2 1 Orientation Standard High Side Left, Low Side Right / Std Head Orientation *
TABLE III AGENCY APPROVALS No Approvals Required 0 * ATEX and IECEx Explosion proof, Intrinsically Safe, Non-incendive & Dustproof A * Approvals c CSA US Explosion proof, Intrinsically Safe, Non-incendive, & Dustproof B * FM Intrinsically Safe, Non-incendive and Dustproof H *
TABLE IV TRANSMITTER ELECTRONICS SELECTIONS Material Connection Paint Color a. Electronic Epoxy Polyester Hybrid Coated Aluminum 1/2 NPT Standard (Blue / Gray) C _ _ _ _ _ * Housing Material Epoxy Polyester Hybrid Coated Aluminum M20 Standard (Blue / Gray) D _ _ _ _ _ * & Connection 316 Stainless Steel (Grade CF8M) 1/2 NPT Standard (no paint) M _ _ _ _ _ * Type 316 Stainless Steel (Grade CF8M) M20 Standard (no paint) N _ _ _ _ _ * Wireless Protocol b. Output/ ISA100 Wireless 2.0 compatible (equivalent OW R300 or newer) _ A _ _ _ _ * Protocol ISA100 Wireless 1.0 compatible (equivalent to OW R2xx) _ B _ _ _ _ * Pow er Options Battery Holder Only - No Battery Included _ _ 0 _ _ _ * c. Power Battery Power - Batteries included _ _ B _ _ _ * 24 VDC power _ _ D _ _ _ * Antenna Options Integral Right-angle, vertical 4 dBi _ _ _ R _ _ * d. Antennas Remote Omnidirectional, 8 dBi _ _ _ M _ _ * Remote Directional, 14 dBi _ _ _ D _ _ * Remote Antenna Adapter only, Type N Connection _ _ _ A _ _ * Remote Antenna Cable None _ _ _ _ 0 _ * e. Remote Antenna Cable Type N Remote Cable, 1.0 m (required for connection to transmitter) _ _ _ _ 1 _ * Type N Remote Cable, 3.0 m (required for connection to transmitter) _ _ _ _ 2 _ * Type N Remote Cable, 10.0 m (required for connection to transmitter) _ _ _ _ 3 _ * Lightning Surge Diverter and Remote Cable None _ _ _ _ _ 0 * f. Surge Diverter Surge Diverter and Type N Cable (1.0 m) _ _ _ _ _ 1 * and Cable Surge Diverter and Type N Cable (3.0 m) _ _ _ _ _ 2 * Surge Diverter and Type N Cable (10.0 m) _ _ _ _ _ 3 *
TABLE V CONFIGURATION SELECTIONS Diagnostics and Applications a. App S/W Standard Diagnostics 1 _ _ _ * Standard Diagnostics plus Anti-Alias Filter 3 _ _ _ * Destination Country Canada _ CA _ * b. Country European Union (RED compliant countries includes Australia) _ EU _ * USA and Puerto Rico _ US _ * c. General General Configuration Configuration Factory Standard _ _ _ S *
SmartLine Wireless Transmitter 15
TABLE VI CALIBRATION & ACCURACY SELECTIONS STAW84L Availability Accuracy and Accuracy Calibrated Range Calibration Qty Calibration Standard Factory Std Single Calibration A *
TABLE VII ACCESSORY SELECTIONS Bracket Type Material None None 0 _ _ _ * a. Mounting Angle Bracket Carbon Steel 1 _ _ _ * Bracket 316 SS * Angle Bracket 3 _ _ _ Flat Bracket Carbon Steel 5 _ _ _ * Flat Bracket 316 SS 7 _ _ _ * Customer Tag Type b. Customer No customer tag _ 0 _ _ * Tag One Wired Stainless Steel Tag (Up to 4 lines 26 char/line) _ 1 _ _ * Two Wired Stainless Steel Tag (Up to 4 lines 26 char/line) _ 2 _ _ * Unassembled Conduit Plugs & Adapters No Conduit Plugs or Adapters Required _ _ A0 * c. Unassembled 1/2 NPT Male to 3/4 NPT Female 316 SS Certified Conduit Adapter _ _ A2 n Conduit 1/2 NPT 316 SS Certified Conduit Plug _ _ A6 n Plugs & M20 316 SS Certified Conduit Plug _ _ A7 m Adapters Minifast® 4 pin (1/2 NPT) (not suitable for X-Proof applications) _ _ A8 n ® Minifast 4 pin (M20) (not suitable for X-Proof applications) _ _ A9 m
TABLE VIII OTHER Certifications & Options: (String in sequence comma delimited (XX, XX, XX,….) None - No additional options required 00 * NACE MR0175; MR0103; ISO15156 (FC33338) Process wetted parts only FG * b NACE MR0175; MR0103; ISO15156 (FC33339) Process wetted and non-wetted parts F7 c EN10204 Type 3.1 Material Traceability (FC33341) FX * Certificate of Conformance (F3391) F3 * b Calibration Test Report & Certificate of Conformance (F3399) F1 * Certificate of Origin (F0195) F5 * Certifications & Over-Pressure Leak Test Certificate (1.5X MAWP) (F3392) TP * Warranty Cert Clean for O2 or CL2 service per ASTM G93 OX e PMI Certification1 PM * Extended Warranty Additional 1 year 01 * Extended Warranty Additional 2 years 02 * Extended Warranty Additional 3 years 03 * b Extended Warranty Additional 4 years 04 * Extended Warranty Additional 15 years 15 *
TABLE IX Manufacturing Specials
Factory Factory Identification 00000 *
16 SmartLine Wireless Transmitter
RESTRICTIONS Available Only with Not Available with Restriction Letter Table Selection(s) Table Selection(s) c I d _ _ _ 0 _ _ _ d VII a 1,2,3,5,6,7_ _ _ e I b _ 2 _ _ _ _ _ m IV a D, N _ _ _ _ _ n IV a C, M _ _ _ _ _ p III B - No CRN number available s I a A,E ______t I a J, K, 7, L, 8 b Select only one option from this group
1The PM option is available on all Smartline Wireless Pressure Transmitter process wetted parts such as process heads, flanges, bushings and vent plugs except plated carbon steel process heads and flanges. PM option information is also available on diaphragms except Gold plated and STGW and STAW in-line construction pressure transmitters.
FIELD INSTALLABLE ACCESSORY KITS Description Kit Number 1/2 NPT cocket plug (ZN plated CS) 50021832-501 1/2 NPT certified conduit plug (SS) 50021832-502 M20 conduit plug (ZN plated CS) 50000547-502 M20 certified conduit plug (SS) 50000547-501 Lightning surge diverter (order cable separately) 50018279-590 IS battery pack 50047517-501 24 VDC external power module 50136118-501 Right-angle elbow assembly for 4dBi antenna, aluminum with gray, pure polyester paint 50030973-503 Right-angle elbow assembly for 4dBi antenna, aluminum with gray, epoxy-polyester paint 50030973-504 Right-angle elbow assembly for 4dBi antenna, stainless steel 50030973-505 Remote omnidirectional antenna, 8 dBi 50018414-501 Remote directional antenna, 14 dBi 50018415-501 Remote antenna adapter, Type N connection 50028364-501 Remote cable for antenna or accessories, Type N (1.0m) 50018278-501 Remote cable for antenna or accessories, Type N (3.0m) 50018278-503 Remote cable for antenna or accessories, Type N (10.0m) 50018278-510 Lithium thionyl chloride batteries (Qty 2) 50026010-501 Lithium thionyl chloride batteries (Qty 4) 50026010-502 Lithium thionyl chloride batteries (Qty 10) 50026010-503
PRODUCT MANUALS Description Part Number SmartLine Wireless Transmitter User's Manual 34-SW-25-01
All product documentation is available at www.honeywellprocess.com.
Sales and Service For application assistance, current specifications, ordering, pricing, and name of the nearest Authorized Distributor, contact one of the offices below.
ASIA PACIFIC EMEA AMERICAS Honeywell Process Solutions, Honeywell Process Solutions, Honeywell Process Solutions, Phone: + 800 12026455 or Phone: + 800 12026455 or Phone: (TAC) (800) 423-9883 +44 (0) 1202645583 +44 (0) 1202645583 or (215) 641-3610 (TAC) hfs-tac- (Sales) 1-800-343-0228 [email protected] Email: (Sales) Email: (Sales) Australia [email protected] [email protected] Honeywell Limited Phone: +(61) 7-3846 1255 or or FAX: +(61) 7-3840 6481 (TAC) (TAC) Toll Free 1300-36-39-36 [email protected] [email protected] Toll Free Fax: 1300-36-04-70
China – PRC - Shanghai Honeywell China Inc. Phone: (86-21) 5257-4568 Fax: (86-21) 6237-2826
Singapore Honeywell Pte Ltd. Phone: +(65) 6580 3278 Fax: +(65) 6445-3033
South Korea Honeywell Korea Co Ltd Phone: +(822) 799 6114 Fax: +(822) 792 9015
For more information To learn more about SmartLine Transmitters, visit www.honeywellprocess.com Or contact your Honeywell Account Manager
Process Solutions Honeywell 1250 W Sam Houston Pkwy S Houston, USA, TX 77042
Honeywell Control Systems Ltd Honeywell House, Skimped Hill Lane Bracknell, England, RG12 1EB
Shanghai City Centre, 100 Jungi Road
Shanghai, China 20061 34-SW-03-02 August 2019 2019 Honeywell International Inc. www.honeywellprocess.com