Technology Limited

VBA100-30 10kHz - 100MHz 30W

l Rugged Silicon DMOS technology l Class A for maximum mismatch drive l General linear power requirements

The VBA100-30 is a member of our family of 10 kHz- Fold-back protection is neither fitted nor needed! This 100 MHz high power , designed primarily for makes it supremely suited for very demanding transducer EMC applications. requirements.

The VBA100 series is based on rugged silicon DMOS technology. The amplifier operates in class A, the benefits for EMC applications being very low distortion and tolerance of 100% mismatch.

Performance Chart

60 Choose Vectawave for high efficiency 50 and performance in your regular power 40 amplifier requirements.

30

20 Typical Saturated Power Power (Watts) Power Typical Linear Power 10 Speci cation Saturated Power Speci cation Linear Power

0 See overleaf for technical specification 0 20 40 60 80 100

Frequency (MHz)

www.vectawave.co.uk Specifications VBA100-30

Electrical Frequency Range (Instantaneous) 0.01-100MHz Rated Output Power 30W Min (40W typical) Output Power at 1dB Gain Compression 25W Min (35W typical) Gain 46dB Min Third Order Intercept Point (see note 1) 54dBm Gain variation with Frequency ±2dB Harmonics at 25W Output Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 85-264V ac Supply Frequency Range 47-63Hz Supply Power <120VA (Max) Mains Connector IEC320

Mechanical RF Connector Style Type N Female Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch, 3U Case, 400mm Deep Mass 12kg Operating Temperature Range 0-40°C Case Style Options Rack mount with Front or Rear panel connectors Bench mount with Front panel connectors

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

Notes 1 The third order intercept point is a nominal value, as its calculation depends upon the power level at which distortion measurements are made. 2 Output VSWR tolerance is specified for excitation within the permitted levels and frequency range.

Represented Worldwide Vectawave Technology Ltd. Unit D, The Apex, St Cross Business Park, Monks Brook, Newport, Isle of Wight, PO30 5XW Technology Limited Tel: +44 (0) 1983 821 818 Designers and Manufacturers of Solid State RF and Amplifiers E-mail: [email protected]

www.vectawave.co.uk Technology Limited

VBA100-110 10kHz - 100MHz 110W Amplifier

l Rugged push-pull MOSFET technology l Class A for maximum mismatch drive l General linear power requirements

The VBA100-110 is a member of our family of 10kHz- The amplifier operates in class A, the benefits for EMC 100MHz high power amplifiers, designed primarily for applications being very low distortion and tolerance of EMC applications. 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very Like all our products of the VBA100 series, it is based on demanding transducer requirements. rugged push-pull MOSFET technology, for extra even order harmonic suppression.

Performance Chart

200 180 Choose Vectawave for high efficiency 160 and performance in your regular power 140 120 amplifier requirements. 100 80 Typical Saturated Power

Power Power (Watts) 60 Typical Linear Power 40 Specification Saturated owerP 20 Specification Linear owerP See overleaf for technical specification 0 20 40 60 80 100

Frequency (MHz)

www.vectawave.co.uk Specifications VBA100-110

Electrical Frequency Range (Instantaneous) 10kHz-100MHz Rated Output Power 110W Min (145W typical) Output Power at 1dB Gain Compression 90W Min (100W typical) Gain 51dB Min Third Order Intercept Point (see note 1) 61dBm Gain variation with Frequency ±2dB Harmonics at 90W Output Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 88-230VAC Supply Frequency Range 47-63Hz Supply Power <500VA (Max) Mains Connector IEC320

Mechanical RF Connector Style Type N Female Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch, 4U Case, 550mm Deep Mass 20kg Operating Temperature Range 0-40°C Case Style Options Rack mount with Front or Rear panel connectors Bench mount with Front panel connectors

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

Notes 1 The third order intercept point is a nominal value, as its calculation depends upon the power level at which distortion measurements are made. 2 Output VSWR tolerance is specified for excitation within the permitted levels and frequency range.

Represented Worldwide Vectawave Technology Ltd. Unit D, The Apex, St Cross Business Park, Monks Brook, Newport, Isle of Wight, PO30 5XW Technology Limited Tel: +44 (0) 1983 821 818 Designers and Manufacturers of Solid State RF and Microwave Amplifiers Fax: +44 (0) 1983 532 737 E-mail: [email protected]

www.vectawave.co.uk Technology Limited

VBA100-200 10kHz - 100MHz 200W Amplifier

l Rugged push-pull MOSFET technology l Class A for maximum mismatch drive l General linear power requirements

The VBA100-200 is a member of our family of 10kHz- The amplifier operates in class A, the benefits for EMC 100MHz high power amplifiers, designed primarily for applications being very low distortion and tolerance of EMC applications. 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very Like all our products of the VBA100 series, it is based on demanding transducer requirements. rugged push-pull MOSFET technology, for extra even order harmonic suppression.

Performance Chart

400 Choose Vectawave for high efficiency 350

300 and performance in your regular power

250 amplifier requirements.

200

150 Typical Saturated Power Power (Watts) Power 100 Typical Linear Power Speci cation Saturated Power 50 Speci cation Linear Power See overleaf for technical specification 0 20 40 60 80 100

Frequency (MHz)

www.vectawave.co.uk Specifications VBA100-200

Electrical Frequency Range (Instantaneous) 10kHz-100MHz Rated Output Power 200W Min (250W typical) Output Power at 1dB Gain Compression 150W Min (180W typical) Gain 51dB Min Third Order Intercept Point (see note 1) 61dBm Gain variation with Frequency ±2dB Harmonics at 150W Output Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 100 - 240V ac (+/- 10%) Supply Frequency Range 45-63Hz Supply Power <1kVA (Max) Mains Connector IEC 320

Mechanical RF Connector Style Type N Female Safety Interlock Dual input, S/C and/or O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch, 4U Case, 500mm deep Mass 18kg Operating Temperature Range 0-40°C Case Style Options Rack mount with Front or Rear panel connectors Bench mount with Front panel connectors

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

Notes 1 The third order intercept point is a nominal value, as its calculation depends upon the power level at which distortion measurements are made. 2 Output VSWR tolerance is specified for excitation within the permitted levels and frequency range.

Represented Worldwide Vectawave Technology Ltd. Unit D, The Apex, St Cross Business Park, Monks Brook, Newport, Isle of Wight, PO30 5XW Technology Limited Tel: +44 (0) 1983 821 818 Designers and Manufacturers of Solid State RF and Microwave Amplifiers E-mail: [email protected]

www.vectawave.co.uk Technology Limited

VBA100-400 10kHz - 100MHz 400W Amplifier

l Robust silicon MOSFET push-pull output design l High efficiency proprietary combiner design l Class A for maximum mismatch drive l General linear power requirements

The VBA100-400 is a member of our family of 10kHz- The amplifier operates in class A, the benefits for EMC 100MHz high power amplifiers, designed primarily for applications being very low distortion and tolerance of EMC applications. 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very Like all our products of the VBA100 series, it is based on demanding and test chamber requirements high performance silicon push-pull MOSFET output stages. The amplifier utilizes exclusive power combining techniques, minimizing loss for a more efficient solution.

Performance Chart

800 Choose Vectawave for high efficiency 700

600 and performance in your regular power

500 amplifier requirements.

400

300

Power Power (Watts) Typical Saturated Power 200 Typical Linear Power Specification Saturated owerP 100 Specification Linear owerP See overleaf for technical specification 0 20 40 60 80 100

Frequency (MHz)

www.vectawave.co.uk Specifications VBA100-400

Electrical Frequency Range (Instantaneous) 10kHz-100MHz Rated Output Power 400W Min (500W typical) Output Power at 1dB Gain Compression 300W Min (400W typical) Gain 57dB Min Third Order Intercept Point (see note 1) 67dBm Gain variation with Frequency ±2dB Harmonics at 250W Output Power Better than -20dBc Harmonics at 300W Output Power Better than -18dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage 184-264V ac Supply Frequency Range 47-63Hz Supply Power <2kVA (Max) Mains Connector IEC320

Mechanical RF Connector Style Type N Female Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch, 9U Rack, 570mm Deep Mass 33kg Operating Temperature Range 0-40°C Case Style Options Rack mount with Rear panel connectors

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

Notes 1 The third order intercept point is a nominal value, as its calculation depends upon the power level at which distortion measurements are made. 2 Output VSWR tolerance is specified for excitation within the permitted levels and frequency range

Represented Worldwide Vectawave Technology Ltd. Unit D, The Apex, St Cross Business Park, Monks Brook, Newport, Isle of Wight, PO30 5XW Technology Limited Tel: +44 (0) 1983 821 818 Designers and Manufacturers of Solid State RF and Microwave Amplifiers Fax: +44 (0) 1983 532 737 E-mail: [email protected]

www.vectawave.co.uk Technology Limited

VBA100-1100 10kHz - 100MHz 1100W Amplifier

l Robust silicon MOSFET push-pull output design l High efficiency proprietary combiner design l Class A for maximum mismatch drive l General linear power requirements

The VBA100-1100 is a member of our family of 10kHz- 100MHz high power amplifiers, designed primarily for EMC applications.

Like all our products of the VBA100 series, it is based on high performance silicon push-pull MOSFET output stages. The amplifier utilizes exclusive power combining techniques, minimizing loss for a more efficient solution.

The amplifier operates in class A, the benefits for EMC applications being very low distortion and tolerance of 100% mismatch. Fold-back protection is neither fitted nor needed! This makes it supremely suited for very demanding antenna and test chamber requirements

Performance Chart

2000 1800 Choose Vectawave for high efficiency 1600 and performance in your regular power 1400 1200 amplifier requirements. 1000 800 600

Power Power (Watts) Typical Saturated Power Typical Linear Power 400 Specification Saturated owerP 200 Specification Linear owerP See overleaf for technical specification 0 20 40 60 80 100

Frequency (MHz)

www.vectawave.co.uk Specifications VBA100-1100

Electrical Frequency Range (Instantaneous) 10kHz-100MHz Rated Output Power 1100W Min (1500W typical) Output Power at 1dB Gain Compression 1000W Min (1300W typical) Gain 62dB Min Third Order Intercept Point (see note 1) 72dBm Gain variation with Frequency ±3dB Harmonics at 1kW Output Power Better than -20dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR Tolerance (see note 2) Infinity:1 Input VSWR 2:1 (Max) Supply Voltage see options for 3 phase configuration Supply Frequency Range 47-63Hz Supply Power <6kVA (Max) Mains Connector Appropriate IEC 60309 plug (see Options)

Mechanical RF Connector Style Type N Female Safety Interlock 2 x BNC, S/C and O/C to Mute USB/GPIB Interface Optional Dimensions 19 inch, 34U Rack, 800mm Deep Mass 200kg Operating Temperature Range 0-40°C Options 3 Phase Delta (5 pin plug) or 3 Phase Star (5 pin plug)

Regulatory Compliance Conducted and Radiated Emissions EN61326 Class A Conducted and Radiated Immunity EN61326:1997 Table 1 Safety EN61010-1

Notes 1 The third order intercept point is a nominal value, as its calculation depends upon the power level at which distortion measurements are made. 2 Output VSWR tolerance is specified for excitation within the permitted levels and frequency range.

Represented Worldwide Vectawave Technology Ltd. Unit D, The Apex, St Cross Business Park, Monks Brook, Newport, Isle of Wight, PO30 5XW Technology Limited Tel: +44 (0) 1983 821 818 Designers and Manufacturers of Solid State RF and Microwave Amplifiers Fax: +44 (0) 1983 532 737 E-mail: [email protected]

www.vectawave.co.uk