Wiring Diagram 3 of Your Idatalink Maestro RR Radio Replacement Solution
Total Page:16
File Type:pdf, Size:1020Kb
SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners. INSTALL GUIDE MITSUBISHI ECLIPSE Base 2006-2012 RETAINS STEERING WHEEL CONTROLS AND ADDS GAUGES PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SI)-MIT01-DS iDatalink Compatible Radio NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. MITSUBISHI ECLIPSE BASE 2006-2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase Wiring Diagram 3 of your iDatalink Maestro RR Radio replacement solution. You are Vehicle Wire Reference Chart 4 now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2014 ADS-RR(SI)-MIT01-DS maestro.idatalink.com 2 MITSUBISHI ECLIPSE BASE 2006-2012 WIRING DIAGRAM STEP 1 OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH BROWN/RED - CANH CANH 1 2 3 4 5 6 7 8 WIRES FROM 9 10 11 12 13 14 15 16 VEHICLE BROWN/YELLOW - CANL CANL NOTE: PIN SIDE VIEW. CONNECT TO TWISTED WIRES BEHIND CONNECTOR. STEP 2 C - LOCATED BEHIND RADIO PURPLE/RED - SWI CIRCUIT 1 INPUT SWI 1 41 40 39 38 37 36 35 34 33 32 31 52 51 50 49 48 47 46 45 44 43 42 BLACK/WHITE - SWI GROUND FEED (-) OUTPUT SWI FEED STEP 3 CONNECT TO AFTERMARKET RADIO RED GRAY/RED - ACCESSORY (+) INPUT YELLOW YELLOW - 12V (+) INPUT BLACK BLACK - GROUND STEP 4 MAESTRO RR MODULE NOT CONNECTED G H A H G A NOT CONNECTED 2 Automotive Data Solutions Inc. © 2014 ADS-RR(SI)-MIT01-DS maestro.idatalink.com 3 MITSUBISHI ECLIPSE BASE 2006-2012 VEHICLE WIRE REFERENCE CHART Wire Connector Connector Connector Wire Position Wire Color Polarity Description Name Color Type Location CanH A ~ 16 pin 06 Red (DATA) OBDII connector, under driver side dash CanL A ~ 16 pin 14 Black (DATA) OBDII connector, under driver side dash SWI 1 C ~ 22 pin 31 Green/Orange (DATA) Behind radio SWI Feed C ~ 22 pin 42 Green/Black (-) Behind radio Automotive Data Solutions Inc. © 2014 ADS-RR(SI)-MIT01-DS maestro.idatalink.com 4 INSTALL GUIDE MITSUBISHI ENDEAVOR Base 2007-2011 RETAINS STEERING WHEEL CONTROLS AND ADDS GAUGES PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SI)-MIT01-DS iDatalink Compatible Radio NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. MITSUBISHI ENDEAVOR BASE 2007-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase Wiring Diagram 3 of your iDatalink Maestro RR Radio replacement solution. You are Vehicle Wire Reference Chart 4 now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2014 ADS-RR(SI)-MIT01-DS maestro.idatalink.com 2 MITSUBISHI ENDEAVOR BASE 2007-2011 WIRING DIAGRAM STEP 1 OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH BROWN/RED - CANH CANH 1 2 3 4 5 6 7 8 WIRES FROM 9 10 11 12 13 14 15 16 VEHICLE BROWN/YELLOW - CANL CANL NOTE: PIN SIDE VIEW. CONNECT TO TWISTED WIRES BEHIND CONNECTOR. STEP 2 C - LOCATED BEHIND RADIO PURPLE/RED - SWI CIRCUIT 1 INPUT SWI 1 41 40 39 38 37 36 35 34 33 32 31 52 51 50 49 48 47 46 45 44 43 42 BLACK/WHITE - SWI GROUND FEED (-) OUTPUT SWI FEED STEP 3 CONNECT TO AFTERMARKET RADIO RED GRAY/RED - ACCESSORY (+) INPUT YELLOW YELLOW - 12V (+) INPUT BLACK BLACK - GROUND STEP 4 MAESTRO RR MODULE NOT CONNECTED G H A H G A NOT CONNECTED 2 Automotive Data Solutions Inc. © 2014 ADS-RR(SI)-MIT01-DS maestro.idatalink.com 3 MITSUBISHI ENDEAVOR BASE 2007-2011 VEHICLE WIRE REFERENCE CHART Wire Connector Connector Connector Wire Position Wire Color Polarity Description Name Color Type Location CanH A ~ 16 pin 06 Red (DATA) OBDII connector, under driver side dash CanL A ~ 16 pin 14 Black (DATA) OBDII connector, under driver side dash SWI 1 C ~ 22 pin 31 Green/Orange (DATA) Behind radio SWI Feed C ~ 22 pin 42 Green/Black (-) Behind radio Automotive Data Solutions Inc. © 2014 ADS-RR(SI)-MIT01-DS maestro.idatalink.com 4 INSTALL GUIDE MITSUBISHI Galant Base 2006-2012 RETAINS STEERING WHEEL CONTROLS AND ADDS GAUGES PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SI)-MIT01-DS iDatalink Compatible Radio NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. MITSUBISHI GALANT BASE 2006-2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase Wiring Diagram 3 of your iDatalink Maestro RR Radio replacement solution. You are Vehicle Wire Reference Chart 4 now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2014 ADS-RR(SI)-MIT01-DS maestro.idatalink.com 2 MITSUBISHI GALANT BASE 2006-2012 WIRING DIAGRAM STEP 1 OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH BROWN/RED - CANH CANH 1 2 3 4 5 6 7 8 WIRES FROM 9 10 11 12 13 14 15 16 VEHICLE BROWN/YELLOW - CANL CANL NOTE: PIN SIDE VIEW. CONNECT TO TWISTED WIRES BEHIND CONNECTOR. STEP 2 C - LOCATED BEHIND RADIO PURPLE/RED - SWI CIRCUIT 1 INPUT SWI 1 41 40 39 38 37 36 35 34 33 32 31 52 51 50 49 48 47 46 45 44 43 42 BLACK/WHITE - SWI GROUND FEED (-) OUTPUT SWI FEED STEP 3 CONNECT TO AFTERMARKET RADIO RED GRAY/RED - ACCESSORY (+) INPUT YELLOW YELLOW - 12V (+) INPUT BLACK BLACK - GROUND STEP 4 MAESTRO RR MODULE NOT CONNECTED G H A H G A NOT CONNECTED 2 Automotive Data Solutions Inc. © 2014 ADS-RR(SI)-MIT01-DS maestro.idatalink.com 3 MITSUBISHI GALANT BASE 2006-2012 VEHICLE WIRE REFERENCE CHART Wire Connector Connector Connector Wire Position Wire Color Polarity Description Name Color Type Location CanH A ~ 16 pin 06 Red (DATA) OBDII connector, under driver side dash CanL A ~ 16 pin 14 Black (DATA) OBDII connector, under driver side dash SWI 1 C ~ 22 pin 31 Green/Orange (DATA) Behind radio SWI Feed C ~ 22 pin 42 Green/Black (-) Behind radio Automotive Data Solutions Inc. © 2014 ADS-RR(SI)-MIT01-DS maestro.idatalink.com 4 INSTALL GUIDE MITSUBISHI LANCER Base 2008 RETAINS STEERING WHEEL CONTROLS AND ADDS GAUGES PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SI)-MIT01-DS iDatalink Compatible Radio NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. MITSUBISHI LANCER BASE 2008 WELCOME TABLE OF CONTENTS Congratulations on the purchase Wiring Diagram 3 of your iDatalink Maestro RR Radio replacement solution. You are Vehicle Wire Reference Chart 4 now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEED HELP? 1 866 427-2999 [email protected] maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2014 ADS-RR(SI)-MIT01-DS maestro.idatalink.com 2 MITSUBISHI LANCER BASE 2008 WIRING DIAGRAM STEP 1 OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH BROWN/RED - CANH CANH 1 2 3 4 5 6 7 8 WIRES FROM 9 10 11 12 13 14 15 16 VEHICLE BROWN/YELLOW - CANL CANL NOTE: PIN SIDE VIEW. CONNECT TO TWISTED WIRES BEHIND CONNECTOR. STEP 2 B - LOCATED BEHIND RADIO PURPLE/RED - SWI CIRCUIT 1 INPUT SWI 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 BLACK/WHITE - SWI GROUND FEED (-) OUTPUT SWI FEED STEP 3 CONNECT TO AFTERMARKET RADIO RED GRAY/RED - ACCESSORY (+) INPUT YELLOW YELLOW - 12V (+) INPUT BLACK BLACK - GROUND STEP 4 MAESTRO RR MODULE NOT CONNECTED G H A H G A NOT CONNECTED 1 Automotive Data Solutions Inc.