SDD 8E9 Silt Fence

Total Page：16

File Type：pdf, Size：1020Kb

SDD 08E09 Silt Fence GENERAL NOTES DETAILS OF CONSTRUCTION NOT SHOWN ON THIS DRAWING SHALL CONFORM ROADWAY ROADWAY ROADWAY TO THE PERTINENT REQUIREMENTS OF THE STANDARD SPECIFICATIONS AND APPLICABLE SPECIAL PROVISIONS. SHOULDER SHOULDER SHOULDER 1 HORIZONTAL BRACE REQUIRED WITH 2" X 4" WOODEN FRAME OR EQUIVALENT A DITCH DIKE AT TOP OF POSTS. INSLOPE FLOW INSLOPE FLOW INSLOPE FLOW FLOW 4 1 2 FOR MANUAL INSTALLATIONS THE TRENCH SHALL BE A MINIMUM OF 4" WIDE AND 1 6" DEEP TO BURY AND ANCHOR THE GEOTEXTILE FABRIC. FOLD MATERIAL TO FIT TRENCH AND BACKFILL AND COMPACT TRENCH WITH EXCAVATED SOIL. 1 1 3 WOOD POSTS SHALL BE A MINIMUM SIZE OF 1 8" X 1 8" OF OAK OR HICKORY. INSLOPE INSLOPE 4 SILT FENCE TO EXTEND ACROSS THE TOP OF THE PIPE. A FLOW FLOW FLOW 5 CONSTRUCT SILT FENCE FROM A CONTINUOUS ROLL IF POSSIBLE BY CUTTING SHOULDER SHOULDER LENGTHS TO AVOID JOINTS. IF A JOINT IS NECESSARY USE ONE OF THE FOLLOWING TWO METHODS; A) OVERLAP THE END POSTS AND TWIST, OR ROTATE, AT LEAST 180 DEGREES, B) HOOK THE END OF EACH SILT FENCE ROADWAY ROADWAY LENGTH. INSLOPE 10'- 0" POST MIN. ** **GEOTEXTILE FABRIC FLOW FLOW GROUND 2 LINE GEOTEXTILE FABRIC SITUATION 1 SITUATION 2 SECTION A - A (TYPICAL) FLOW PLAN VIEW DIRECTION 2 PLAN VIEW SILT FENCE AT MEDIAN SURFACE DRAINS TYPICAL APPLICATION OF SILT FENCE EXCESS FABRIC FLOW DIRECTION TRENCH DETAIL NOTE: ADDITIONAL POST DEPTH OR GEOTEXTILE TIE BACKS MAY BE REQUIRED FOLD 6 3" MAX. FABRIC 6 IN UNSTABLE SOIL. SUPPORT CORD OR TENSION TAPE 3 WOOD POSTS 4' - 0" MIN. LENGTH 2' - 0" MIN. DEPTH GEOTEXTILE FABRIC IN GROUND WOOD POST TIEBACK BETWEEN FENCE 3'- 0" MAX. POST AND ANCHOR FLOW * 2'- 0"± 3'- 0" MAX. WOOD POST GEOTEXTILE SILT FENCE * FABRIC FLOW DIRECTION 3'- 0" MAX. TWIST METHOD GEOTEXTILE * ANCHOR STAKE FABRIC ONLY 3'- 0" MAX. MIN. 18" LONG * FLOW DIRECTION SILT FENCE TIE BACK BACKFILL AND COMPACT GEOTEXTILE TRENCH WITH EXCAVATED SOIL FABRIC (WHEN REQUIRED BY THE ENGINEER) SDD ATTACH THE FABRIC TO THE POSTS WOOD POST 15' MAX. WITH WIRE STAPLES OR WOODEN GEOTEXTILE LATH AND NAILS FABRIC 1'- 0" MIN 2 SILT FENCE 08E09 - 06 FLOW DIRECTION 2'- 0" MIN. WOOD POST * NOTE: 8' - 0" SPACING ALLOWED IF A WOVEN GEOTEXTILE HOOK METHOD STATE OF WISCONSIN FABRIC IS USED. DEPARTMENT OF TRANSPORTATION 08E09 - 06 5 APPROVED SILT FENCE JOINING TWO LENGTHS OF SILT FENCE 4/29/05 /S/ Beth Cannestra DATE CHIEF ROADWAY DEVELOPMENT ENGINEER FHWA SDD Version 6 Standard Detail Drawing 8E9 July 5, 2005 Silt Fence References: FDM 10-10-23 Bid items associated with this drawing: ITEM NUMBER DESCRIPTION UNIT 628.1504 Silt Fence ........................................................................................................ LF 628.1520 Silt Fence Maintenance .................................................................................... LF Standardized Special Provisions associated with this drawing: STSP NUMBER TITLE NONE Other SSDs associated with this drawing: NONE Design Notes: Silt Fence is not recommended for channel applications. Increase the calculated need for silt fence by 25% and list this quantity as "undistributed" on the miscellaneous quantities sheet. Silt Fence is neither biodegradable, recyclable, nor reusable and, therefore is recommended only when other erosion control best management practices are not practical. Contact Person: Jeremy Ashauer (920) 412-6381 .

Copy Link

Recommended publications

Silt Fence Note
9/3/2020 9:29:31 AM N:\CFL-DPIT\Drawings\FP-14\FP14_Details\C157-50.dgn _User: Angela.Johnson_ POST ANDGEOTEXTILEINSTALLATIONDETAIL See EndPostsDetail End posts ELEVATION 18" min. 30" min. See note5 Geotextile END POSTSDETAIL Fil l s lo pe 24" min. See Note3 END DETAIL PLAN 6" min. Backfilled andcompactedsoil F Fence supportmesh(optional) l Steel orwoodpost o See note5 Geotextile Staple ortie w Steel orwoodpost 6" min.trench PLAN Toe of slope See Note3 Posts Detail See End End posts (undisturbed) Existing ground Limits ofclearing SILT FENCEINSTALLATIONATTOEOFFILL for spacing See Note4 SILT FENCE ASPERIMETER CONTROL Existing ground A A Roadway Edge ofshoulder See TypicalSectionSheet Edge ofshoulder SECTION A-A Fill ELEVATION Varies Varies PLAN PLAN Flow Flow Toe ofslope Toe ofslope Silt fence S h Toe of slope e F e il t l s f l l o o p w e Silt fence Top ofpoststiedtogether. Posts driventightlytogether. Steel orwoodposts NO SCALE See note5 Section A Geotextile POSTS ATJOINTS REVISED: 08/2014 07/2020 5. 4. 3. 2. 1. NOTE: 713.16(a). Furnish geotextileconformingtosubsection 6 ft.(max.) Post spacing 10 ft.(max.) Post spacing running aroundtheends. fence uptheslopetopreventwaterfrom As theslopeisconstructed,curvesilt contours ascloselypossible. Install siltfencetofollowtheground manufacturer's recommendations. machine-sliced siltfenceaccordingtothe slicing asapprovedbytheCO.Install Silt fencemaybeinstalledusingmachine CENTRAL FEDERALLANDSHIGHWAYDIVISION PLAN DETAIL APPROVEDFORUSE U.S. DEPARTMENTOFTRANSPORTATION FEDERAL HIGHWAYADMINISTRATION U.S. CUSTOMARYDETAIL SILT FENCE without with STATE Fasten fabrictoposts. each postonefullturn. Fold geotextilearound fencesupportmesh= Staple ortie fencesupportmesh= See note5 Section B Geotextile PROJECT C157-50 DETAIL NUMBER SHEET NOTES TO THE DESIGNER Last Updated: July 2020 General Information 1.
[Show full text]
Strengthening Silt Fences
Article 56 Feature article from Watershed Protection Techniques. 2(3): 424-428 Strengthening Silt Fence ilt fences are one of the most widely used and reality, settling is actually the most important sedi- misused erosion and sediment control practices. ment removal function of silt fences (Kouwen, 1990), SRecent data suggest that they can perform well since runoff is detained behind the fence, giving sedi- under some circumstances. In addition, their cost- ment time to settle out. effectiveness continues to make them a popular ESC Three recent studies report sediment removal ef- technique. Unfortunately, silt fences are often used ficiencies ranging from 36 to 86% (Table 1). It is al- inappropriately or are improperly installed or maintained, most impossible to accurately predict the field perfor- resulting in poor performance. Simple improvements to mance of silt fences because relatively little research the standard silt fence, as well as some innovative has been done, and the results are so variable. This designs, can help to improve the current state of silt being said, some useful information emerges from fences. available data. First, these studies suggest that silt fences are more effective at removing coarser-grained How, and How Well, Do They Work? materials. Conversely, silt fences are ineffective at Silt fences trap sediment in construction runoff be- reducing turbidity, which is disproportionately influ- fore it washes into the street, a neighboring property or, enced by finer particles (Horner et al., 1990). A sec- in the worst case, a nearby stream or wetland. As sedi- ond finding is that silt fences are less effective on ment-laden runoff flows through the silt fence, the pores steeper slopes.
[Show full text]
Silt Fence Installation Guidelines
Silt Fence Installation Guidelines Sediment Control QUALITY - SUPPORT - EXPERTISE Silt Fence Installation Guidelines 2 00m m de ep 200mm STEP 1 STEP 2 Installation STEP 1 Excavate a trench a minimum of 200mm wide and 200mm deep on STEP 3 the uphill side of the proposed line of silt fence. STEP 2 Drive adequate length support posts to a depth (minimum 400mm) appropriate for the site conditions downhill of the trench. A. Post spacing is typically at 2m centres with wire attached along the top between posts to assist with support of the silt fence. B. Post spacing can be increased up to 4m centres if supported by 2.5mm diameter high tensile wire at mid height and along the top 600mm with hog rings, clips or pins every 150mm connecting the silt fence along the top wire. STEP 3 Roll out silt fence and position up against the support posts and fold over top wire. Hog rings, clips or pins are used to attach the silt fence to the top wire (at the required spacing). STEP 4 STEP 4 Bury bottom section along the base and up the side of the trench leaving a minimum exposed height of 600mm and backfill with soil. Compact to ensure good anchorage. Place safety caps on posts. NOTE Installation to follow your local Regional Council guidelines for erosion control and sediment control. Maintenance Regular inspection of silt fence is required especially after each rainfall event. Make any necessary repairs and remove excessive silt deposits to reduce pressure on the silt fence. NEW ZEALAND AUCKLAND HAMILTON NAPIER CHRISTCHURCH (64) 9 634 6495 (64) 21 732 178 (64) 21 916 736 (64) 3 349 5600 MELBOURNE SYDNEY NEWCASTLE COFFS HARBOUR PERTH ADELAIDE AUSTRALIA (03) 8586 9111 (02) 8785 8800 (02) 4951 2688 (02) 6653 5706 (08) 6305 0561 (08) 8162 5855 HOBART BRISBANE TOWNSVILLE BUNDABERG GOLD COAST DARWIN (03) 6273 0511 (07) 3279 1588 (07) 4774 8222 (07) 4155 9968 (07) 5594 8600 0407 523 669 0800 60 60 20 (Freephone NZ only) Follow GEOFABRICS.CO.NZ Geofabrics on GEOFABRICS.COM.AU The information contained in this brochure is general in nature.
[Show full text]
Silt Fences Allow Sediment to Settle from Runoff Before Water Leaves the Construction Site
Silt Fence SC-1 BMP Objectives ○ Soil Stabilization ● Sediment Control ○ Tracking Control ○ Wind Erosion Control ○ Non-Storm Water Management ○ Materials and Waste Management Definition and Purpose A silt fence is a temporary linear sediment barrier of permeable fabric designed to intercept and slow the flow of sediment-laden sheet flow runoff. Silt fences allow sediment to settle from runoff before water leaves the construction site. Appropriate Applications Silt fences are placed: n Below the toe of exposed and erodible slopes. n Down-slope of exposed soil areas. n Around temporary stockpiles. n Along streams and channels. Limitations n Not effective unless trenched and keyed in. n Not intended for use as mid-slope protection on slopes greater than 4:1. n Must be maintained to remain effective. n Not intended for use in streams, channels, or anywhere flow is concentrated. n Difficult to install and maintain in windy areas. n Must be removed and disposed of. 70 Design Guidelines and Considerations n Do not use below slopes subject to creep, slumping, or landslides. n Do not use in streams, channels, or anywhere flow is concentrated. n Do not use silt fences to divert flow. n The maximum length of slope upgradient of the silt fence should be 60 m (200 ft) or less to minimize flow volumes and velocities and increase the effectiveness of the silt fence. n Slope of areas draining to fence should be less than 1:1 but can be used below steeper slopes at the Engineers discretion. n Limit to locations suitable for temporary ponding or deposition of sediment.
[Show full text]
Straw Wattles
EROSION & SEDIMENT CONTROL PRODUCT OVERVIEW Straw Wattles Straw wattles are an effective and economical Straw wattles are available in two sizes: alternative to silt fence and straw bales for • 9 inch (22.86 cm) diameter sediment control and storm water runoff. • 12 inch (30.48 cm) diameter Cylinders of recycled, compressed, 100% agricultural straw, straw wattles are wrapped in Advantages of Straw Wattles tubular, UV-stabilized black synthetic netting. • Increased weight per linear foot for less Straw wattles can be placed and staked along resistance to movement from wind, water and the contour of newly constructed or disturbed sediment load. slopes. Fertile topsoil, organic matter, and native • Low-cost solution to sheet and rill erosion seeds are trapped behind straw wattles and problems. provide a stable medium for germination. Straw • Replaces silt fence or straw bales on steep wattles also retain moisture from rainfall, aiding slopes. the growth of tree seedlings planted to their up- • Lasts up to two years. slope side. • Stores moisture for vegetation planted immediately up-slope. • The straw incorporates into the soil over time, adding organic material to the soil and retaining moisture for vegetation. • Can be staked with fascines to stabilize low- velocity stream banks and establish wetland plants. Straw Wattles Applications for Straw Wattles The Nilex Advantage • Control stormwater runoff. Diverts flow and Nilex is committed to unearthing better directs stormwater to treatment areas. results. Whether it’s for a civil, resource or • Prevent off-site sedimentation at active environmental project, we offer the latest construction sites. Keeps soil on-site and engineered and technically superior materials prevents it from washing onto pavement and techniques to save our customers time and asphalt; an economical and effective and money, and minimize the need to move or perimeter control alternative to silt fence and remove earth, and reduce the need for granular straw bales.
[Show full text]
Silt Fence (1056)
Silt Fence (1056) Wisconsin Department of Natural Resources Technical Standard I. Definition IV. Federal, State, and Local Laws Silt fence is a temporary sediment barrier of Users of this standard shall be aware of entrenched permeable geotextile fabric designed applicable federal, state, and local laws, rules, to intercept and slow the flow of sediment-laden regulations, or permit requirements governing sheet flow runoff from small areas of disturbed the use and placement of silt fence. This soil. standard does not contain the text of federal, state, or local laws. II. Purpose V. Criteria The purpose of this practice is to reduce slope length of the disturbed area and to intercept and This section establishes the minimum standards retain transported sediment from disturbed areas. for design, installation and performance requirements. III. Conditions Where Practice Applies A. Placement A. This standard applies to the following applications: 1. When installed as a stand-alone practice on a slope, silt fence shall be placed on 1. Erosion occurs in the form of sheet and the contour. The parallel spacing shall rill erosion1. There is no concentration not exceed the maximum slope lengths of water flowing to the barrier (channel for the appropriate slope as specified in erosion). Table 1. 2. Where adjacent areas need protection Table 1. from sediment-laden runoff. Slope Fence Spacing 3. Where effectiveness is required for one < 2% 100 feet year or less. 2 to 5% 75 feet 5 to 10% 50 feet 4. Where conditions allow for silt fence to 10 to 33% 25 feet be properly entrenched and staked as > 33% 20 feet outlined in the Criteria Section V.
[Show full text]
Silt Fences: an Economical Technique for Measuring Hillslope Soil Erosion
United States Department of Agriculture Silt Fences: An Economical Technique Forest Service for Measuring Hillslope Soil Erosion Rocky Mountain Research Station General Technical Peter R. Robichaud Report RMRS-GTR-94 Robert E. Brown August 2002 Robichaud, Peter R.; Brown, Robert E. 2002. Silt fences: an economical technique for measuring hillslope soil erosion. Gen. Tech. Rep. RMRS-GTR-94. Fort Collins, CO: U.S. Department of Agriculture, Forest Service, Rocky Mountain Research Station. 24 p. Abstract—Measuring hillslope erosion has historically been a costly, time-consuming practice. An easy to install low-cost technique using silt fences (geotextile fabric) and tipping bucket rain gauges to measure onsite hillslope erosion was developed and tested. Equipment requirements, installation procedures, statis- tical design, and analysis methods for measuring hillslope erosion are discussed. The use of silt fences is versatile; various plot sizes can be used to measure hillslope erosion in different settings and to determine effectiveness of various treatments or practices. Silt fences are installed by making a sediment trap facing upslope such that runoff cannot go around the ends of the silt fence. The silt fence is folded to form a pocket for the sediment to settle on and reduce the possibility of sediment undermining the silt fence. Cleaning out and weighing the accumulated sediment in the field can be accomplished with a portable hanging or plat- form scale at various time intervals depending on the necessary degree of detail in the measurement of erosion (that is, after every storm, quarterly, or seasonally). Silt fences combined with a tipping bucket rain gauge provide an easy, low-cost method to quantify precipitation/hillslope erosion relationships.
[Show full text]
The Fairfax County Erosion and Sediment Control Checklist
DEPARTMENT OF PUBLIC WORKS AND ENVIRONMENTAL SERVICES, COUNTY OF FAIRFAX OFFICE OF SITE DEVELOPMENT SERVICES ENVIRONMENTAL AND FACILITIES REVIEW DIVISION EROSION AND SEDIMENT CONTROL CHECKLIST Project Name: Project #: Tax Map #: District: Design Engineer: Plan Reviewer: Date: Abbreviations PFM: Fairfax County Public Facilities Manual VESCH: Virginia Erosion and Sediment Control Handbook CC: Fairfax County Code MS: Minimum State Standard LTI: Fairfax County Letter to Industry Shown on Item # Code Section Requirement OK NO N/A Plan Sheet # 1 NARRATIVE All plans must have Erosion and Sediment Control Narrative. The narrative should be site specific and include the PFM 11 -0405.8.B following items: 1.1 VESCH 7A-2 Project Description- Briefly describe the purpose and nature of land disturbing activity, and the area to be disturbed. 1.2 VESCH 7A-2 Existing Site Condition - Description of existing topography, vegetation and drainage Adjacent Areas - a Brief description of neighboring areas such as streams, lakes, ponds, floodplain, Resources 1.3 VESCH 7A-2 Protection Area (RPA), Environmental Quality Corridor (EQC) or residential areas which might be affected by this project. 1.4 VESCH 7A-2 Off-site areas - Describe any off-site land-disturbing activities that will occur including borrow sites, waste or surplus areas. Critical Areas - A description of areas on the site which have potential serious erosion problem (e.g., steep slopes, 1.5 VESCH 7A-2 channels, wet weather/underground springs) Soils - A description of areas on the site giving such information as soil name, mapping unit, erodibility, permeability, 1.6 VESCH 7A-2 depth, texture and soil structure.
[Show full text]
4.5-R SILT FENCE
4.5-r SILT FENCE Alternative Names: Filter Fence, Erosion Control Fence (EC Fence) BMP DESIGN APPROACH DESCRIPTION Pollutant Source Control Hydrologic Source Silt fences are temporary sediment control barriers used to intercept and detain Control sediment while decreasing the velocity of runoff. Silt fences usually consist of geotextile filter fabric spread along the contour and anchored into the soil. Steel or Stormwater wood posts are used to support the silt fence. In many cases, a wire mesh fence is Treatment used as a back support for the silt fence. SCALE OF APPLICATION All SFR and MFR < 1 SITE SUITABILITY acre Used for sediment control when positioned below the toe of an exposed and/or MFR 1-5 Acre and erodible slope (or placed below other small cleared areas). CICU < 5 acres Used to prevent sediment from entering streams, channels, bodies of water, and MFR and CICU > 5 acres and all WQIPs other sensitive areas. TYPE OF APPLICATION Along paved surfaces adjacent to exposed and/or erodible bare soil areas. Temporary Placed around temporary stock piles. Permanent Advantages Intercepts and captures sediment generated from surface runoff within a project area. Prevents sedimentation damage to adjacent properties. Minimizes degradation of water quality, especially when used adjacent to water courses. Reduces runoff velocity and therefore the erosive capacity of any concentrated runoff generated from the project area. Disadvantages Even if properly maintained, the life expectancy of a silt fence is generally limited to six months to one year. Silt fences cannot be used in channels, streams, ditches, and other locations of concentrated flow.
[Show full text]
Silt Fence SE-1
Silt Fence SE-1 Categories EC Erosion Control SE Sediment Control ; TC Tracking Control WE Wind Erosion Control Non-Stormwater NS Management Control Waste Management and WM Materials Pollution Control Legend: ; Primary Category : Secondary Category Targeted Constituents Description and Purpose Sediment ; A silt fence is made of a woven geotextile that has been Nutrients entrenched, attached to supporting poles, and sometimes Trash backed by a plastic or wire mesh for support. The silt fence detains sediment-laden water, promoting sedimentation Metals behind the fence. Bacteria Oil and Grease Suitable Applications Organics Silt fences are suitable for perimeter control, placed below areas where sheet flows discharge from the site. They could also be used as interior controls below disturbed areas where Potential Alternatives runoff may occur in the form of sheet and rill erosion and SE-5 Fiber Rolls around inlets within disturbed areas (SE-10). Silt fences are SE-6 Gravel Bag Berm generally ineffective in locations where the flow is concentrated and are only applicable for sheet or overland flows. Silt fences SE-8 Sandbag Barrier are most effective when used in combination with erosion SE-10 Storm Drain Inlet Protection controls. Suitable applications include: SE-14 Biofilter Bags Along the perimeter of a project. Below the toe or down slope of exposed and erodible slopes. Along streams and channels. Around temporary spoil areas and stockpiles. Around inlets. Below other small cleared areas. November 2009 California Stormwater BMP Handbook 1 of 8 Construction www.casqa.org Silt Fence SE-1 Limitations Do not use in streams, channels, drain inlets, or anywhere flow is concentrated.
[Show full text]
Silt Fence SE-1
Silt Fence SE-1 Categories EC Erosion Control SE Sediment Control TC Tracking Control WE Wind Erosion Control Non-Stormwater NS Management Control Waste Management and WM Materials Pollution Control Legend: Primary Category Secondary Category Description and Purpose Targeted Constituents A silt fence is made of a woven geotextile that has been Sediment (coarse sediment) entrenched, attached to supporting poles, and sometimes Nutrients backed by a plastic or wire mesh for support. The silt fence Trash detains water, promoting sedimentation of coarse sediment Metals behind the fence. Silt fence does not retain soil fine particles like clays or silts. Bacteria Oil and Grease Suitable Applications Organics Silt fences are suitable for perimeter control, placed below areas where sheet flows discharge from the site. They could Potential Alternatives also be used as interior controls below disturbed areas where runoff may occur in the form of sheet and rill erosion and SE-5 Fiber Rolls around inlets within disturbed areas (Storm Drain Inlet SE-6 Gravel Bag Berm SE-12 Protection, SE-10). Silt fences should not be used in locations Manufactured Linear Sediment where the flow is concentrated. Silt fences should always be Controls used in combination with erosion controls. Suitable SE-13 Compost Socks and Berms applications include: SE-14 Biofilter Bags ◼ At perimeter of a project (although they should not be installed up and down slopes). ◼ Below the toe or down slope of exposed and erodible slopes. ◼ Along streams and channels. ◼ Around temporary spoil areas and stockpiles. ◼ Around inlets. ◼ Below other small cleared areas. September 2020 Napa County 1 of 8 LNU Lightning Complex 2020 BMPs Based upon CASQA Construction BMP Online Handbook (2019) Silt Fence SE-1 Limitations ◼ Do not use in streams, channels, drain inlets, or anywhere flow is concentrated.
[Show full text]
Straw Wattle Installation
Straw Wattles Straw Wattles are an effective and economical alternative to silt fence and straw bales for sediment control and storm water runoff. Straw Wattles can be placed and staked along the contour of newly constructed or disturbed slopes. Their use to capture and keep sediment on the slopes is a best management practice (BMP). Fertile topsoil, organic matter, and native seeds are trapped behind Straw Wattles, and provide a stable medium for germination. Straw Wattles also retain moisture from rainfall, aiding the growth of tree seedlings planted to their up-slope side. Straw Wattles are available in 9-inch diameter, 25-foot lengths and in 12-inch diameter, 10-foot lengths. They are installed by staking in place, and can be used individually or tied together to achieve any desired length. Advantages of Straw Wattles Increased weight per linear foot for less resistance to movement from wind, water, and sediment load Low-cost solution to sheet and rill erosion problems Replaces silt fence or straw bales on steep slopes Lasts up to two years Stores moisture for vegetation planted immediately up-slope The straw incorporates into the soil over time, adding organic material to the soil and retaining moisture for vegetation Can be staked with fascines to stabilize low-velocity stream banks and establish wetland plants Applications for Straw Wattles Control Stormwater Runoff o Diverts flow and directs stormwater to treatment areas. Prevent Off-Site Sedimentation at Active Construction Sites o Keeps soil on-site and prevents it from washing onto pavement and asphalt; an economical and effective perimeter control alternative to silt fence and straw bales.
[Show full text]