8/27/2018 Engine, 1.4l I4 16v Turbo • Cylinder Head • Removal • 2013 Dart (1.4L) - PF • MotoLogic

2013 Dart (1.4L) - PF

REMOVAL Report a problem with this article Labor Operations: Click to display a list of Labor Operations associated with this procedure

CAUTION: Prior to removing the cylinder head, the camshaft and crankshaft MUST be aligned and locked into position. If the procedure is not performed, SEVERE DAMAGE will result. The camshaft and the crankshaft MUST be locked with the appropriate special tools.

NOTE: Refer to the timing belt removal service procedure for special tool information

(Refer to 09 - Engine/Valve Timing/BELT, Timing/Removal)

1. Disconnect and isolate the negative battery cable.

2. Perform the fuel pressure release procedure (Refer to 14 - Fuel System/Fuel Delivery/Standard Procedure) .

3. Remove the camshaft bearing housing (Refer to 09 - Engine/Cylinder Head/HOUSING, Camshaft Bearing - Removal) .

4. Remove the exhaust manifold (4) (Refer to 09 - Engine/Manifolds/MANIFOLD, Exhaust - Removal) .

https://www.motologic.com/car/2013_dodge_pf_dodge_dart_1_4l_i4_16v_turbo/article/c32d817d5769ad1630064b9535231475?returnPath=%2Fcar%… 1/4 8/27/2018 Engine, 1.4l I4 16v Turbo • Cylinder Head • Removal • 2013 (1.4L) - PF • MotoLogic

5. Remove the intake manifold (Refer to 09 - Engine/Manifolds/MANIFOLD, Intake/Removal) .

6. Remove the bolt (2) and the side timing belt cover (1).

CAUTION: The vacuum hose and the afterrun coolant pump hose have the same quick- connect fitting end. If removing both hoses, it is recommended that the hoses be marked at disassembly to avoid an incorrect installation. Failure to properly install the hoses can result in engine damage.

https://www.motologic.com/car/2013_dodge_pf_dodge_dart_1_4l_i4_16v_turbo/article/c32d817d5769ad1630064b9535231475?returnPath=%2Fcar%… 2/4 8/27/2018 Engine, 1.4l I4 16v Turbo • Cylinder Head • Removal • 2013 Dodge Dart (1.4L) - PF • MotoLogic

7. Disconnect the afterrun coolant pump hose (2).

8. Loosen the clamp (3) and disconnect the lower radiator hose.

9. Remove the bolt (4) and disconnect the oil filter housing coolant return hose.

10. Unlock and disconnect the Engine Coolant Temperature (ECT) sensor wire harness connector (2).

11. Disconnect the heater core inlet hose (1).

12. Using the sequence shown, remove the cylinder head retaining bolts.

13. Remove the cylinder head and gasket (1). Discard the gasket.

https://www.motologic.com/car/2013_dodge_pf_dodge_dart_1_4l_i4_16v_turbo/article/c32d817d5769ad1630064b9535231475?returnPath=%2Fcar%… 3/4 8/27/2018 Engine, 1.4l I4 16v Turbo • Cylinder Head • Removal • 2013 Dodge Dart (1.4L) - PF • MotoLogic

14. If required, remove the bolts (2) and the thermostat housing from the cylinder head.

15. If required, remove the tensioner lock nut (1) and the tensioner (2) from the cylinder head.

https://www.motologic.com/car/2013_dodge_pf_dodge_dart_1_4l_i4_16v_turbo/article/c32d817d5769ad1630064b9535231475?returnPath=%2Fcar%… 4/4