IMPORTANT:

Go to www.extron.comore for connecting the complete the user guide, installation instructions, and specifications bef XTP T HD 4K and XTP R HD 4K • Setup Guide product to the power source.

The XTP T HD 4K Transmitter and XTP R HD 4K Receiver are XTP® extenders for video, audio, bidirectional control, and Ethernet transmission over a shielded cable. This guide provides instructions for an experienced installer to install and connect the XTP T HD 4K and XTP R HD 4K.

Transmitter Connectors Receiver Connectors AB CDEFG A DC power connector H DC power connector SIG LINK POWER INPUTS OVER XTP 12V AUDIO AUDIO B HDMI input connector I XTP input connector 0.7A MAX ON LR RS-232 IR RESET

XTP T HD 4K OFF HDMI LOOP THRU −+ −+ Tx Rx G RxTx C HDMI Loop-Thru connector J LAN connector XTP OUT LAN and HDMI audio switch K RS-232 and IR Over XTP XTP T HD 4K D Analog Audio input connector connector L HDMI output connector and E RS-232 and IR Over XTP HDMI audio switch HIJKLMNO connector SIG LINK Analog audio output connector POWER OVER XTP OUTPUTS RELAYS XTP R HD 4K M 12V AUDIO AUDIO 1.1A MAX RS-232 IR L R 1 2 XTP output connector ON RESET F S/PDIF audio output connector OFF N -+ XTP IN LAN Rx GTx Tx Rx HDMI -+-+ S/PDIF LAN connector G O Relay connectors XTP R HD 4K Figure 1. Rear Panel Connectors Installation

Before starting, turn off or disconnect all equipment power sources and mount the transmitter or receiver on a table or in a rack.

Input Connections

1. Connect a digital video source to the female HDMI connector (see figure 1,B ) on the transmitter. It accepts HDMI, DVI (with an appropriate adapter), or dual mode DisplayPort video signals.

NOTES: • Use an Extron LockIt® Lacing Bracket to secure HDMI cables to the rear panel connectors. • Video input from a DisplayPort source must be a dual mode DisplayPort source.

2. Connect a digital video display to the HDMI Loop-thru connector (C) on the transmitter to locally display the input source. A display that is not HDCP-compliant displays a green screen when HDCP-encrypted content is sent to it. 3. Connect balanced or unbalanced stereo audio to Tip LR LR the 3.5 mm, 5-pole captive screw connector ( ). Ring Tip D Sleeves Sleeve Wire the connector as shown to the right. Tip Tip Ring Sleeve Do not tin XTP Interconnections Balanced Stereo Input Unbalanced Stereo Input the wires!

1. For the transmitter, connect a shielded twisted pair cable between the XTP output connector on the transmitter (F) and the XTP input connector on an XTP twisted pair receiver or XTP matrix switcher. For the receiver, connect a shielded twisted pair cable between the XTP input connector on the receiver (I) and the XTP output connector Pins: 12345678 TIA/EIA-T568B on an XTP twisted pair transmitter or XTP matrix switcher. T568A T568B PinPin WireWire Color color Wire color 1 White-green White-orange ATTENTION: Do not connect this connector to a computer data or 1 White-orange telecommunications network. 2 Green Orange 2 3 White-orangeOrange White-green The XTP T HD 4K and XTP R HD 4K are compatible with shielded twisted pair (F/UTP, 3 4 BlueWhite-green Blue SF/UTP, and S/FTP) cables. Extron recommends using the following practices to achieve 5 White-blue White-blue 4 Blue full transmission distances up to 330 feet (100 meters) and reduce transmission errors. 6 Orange Green 5 7 White-brownWhite-blue White-brown • Use Extron XTP DTP 24 SF/UTP cable for the best performance. At a minimum, 8 Brown Brown Insert Twisted 6 Green Extron recommends 24 AWG, solid conductor, STP cable with a minimum bandwidth Pair Wires of 400 MHz. RJ-45 7 White-brown Connector • Terminate cables with shielded connectors to the TIA/EIA-T568B standard. 8 Brown • Limit the use of more than two pass-through points, which may include patch points, punch down connectors, couplers, and power injectors. If these pass-through points are required, use shielded couplers and punch down connectors. 1

2 Operation Configuration andControl HDMI AudioSwitch Control Devices,Relays, andPowerConnections Output Connections DataViewer (seetheXTPTHD4KandR UserGuideatwww.extron.com). device, usetheExtron XTPSystemConfigurationSoftware (recommended) orSimpleInstructionSet(SIS™)commandsin To directly configure thetransmitteror receiver, connectahost device tothefront panel USB configurationport.Onthehost On eitherdevice,moveandhold(forabout1second)theHDMI audio switch( After theXTPdevicesandallconnectedare properly connectedandpowered on,thesystemisfullyoperational. 3. 2. 1. 3. 2. 1. 3. 2. been released. TheassociatedLEDlightswhenaudioisenabled andremains unlitwhenaudioisdisabled. display connectedtotheassociatedHDMIconnectorordown to disable it.Theswitchreturns tothemiddlepositionafterithas

to theright)oftransmitterorreceiver to configure thedeviceorupdatefirmware. • • • Power eitherdeviceinoneofthefollowingmethods: to thesenormallyopenrelays ( Connect theequipmentcontrolled via momentaryorlatchingcontact,likeprojector screens orlifts, Connect ahostdevice,suchascomputer, tothefront panelfemaleUSBmini-Bconnector(see RCA connector( Connect anaudiodevicetothefemaleorange captive screw connector( or monoaudiodevicetothe3.5mm,5-pole Connect abalancedorunbalanced,stereo Connect adigitalvideodisplaytotheHDMIoutputconnector( Connect ahostdeviceorcontrol LANorWAN totheLANRJ-45connector( the devicetoRS-232andIROverXTPconnector(seefigure 1, To passbidirectional serialorinfrared signalstoacontrol orcontrolled device,connect connector asshowntotheright. for 2-channelstereo analogaudio. Wire the status. for pass-through communication.TheLEDsindicatelinkandactivity 10/100Ethernet previous page).Wire theconnectorasshowntoright.

NOTE: NOTE: © 2016Extron Electronics —All rightsreserved. Alltrademarksmentioned are theproperty oftheirrespective owners. www.extron.com Connect thetransmitterorreceiver toanXTPmatrixswitcherandenableremote powerontheXTPmatrixswitcher. www.extron.com), and alocallypowered XTPendpointdevice orXTPmatrixswitcher(seethePowerInjectoruserguideat Connect anXTPPowerInjectortothetwistedpairinterconnection betweenanunpowered transmitterorreceiver Connect theprovided powersupplytothe2-polecaptivescrew external connector( • • • •

Separate twistedpaircablesfrom ACpowercables. Loosely placecablesandlimittheuseoftiewrapsorhook-and-loop fasteners. Do notcombthecableforfirst20meters,where cablesare straightened, aligned,andsecured intightbundles. Do notexceed40%fillcapacityinconduits.

RS-232 andIRdatacanbetransmittedsimultaneously When usingshieldedtwistedpaircableinbundlesorconduits,considerthefollowing: N ) torfordigitalS/PDIFaudiooutput. M ) onthereceiver O ). Donotexceed24Vat1Aforeachport. Slee Ring Ring ve Tip Tip s Balanced Audio Output L ) onthereceiver. . E and C K

G and LR onthe and L Slee No GroundHere No GroundHere J ) uptoenableembeddedaudioona ve Tip Tip Unbalanced Audio Output s ) A and Tx/Rx

RS-232 IR Pins

H Tx Rx G Tx Rx P ) forlocalpower.

LR 68-2716-50 Rev. A RS-232 Device

the wires! Do nottin IR Device CONFIG RxTx TxRx P G G 11 16 S SIGNAL HD HDCP I G CP NA L HDMI AUDIO HDMI A ANALOG AUDIOA NAL OG U INPUINP AUDI DI O U O T T AUDIO SIGNALCLIPAU DI O

S I G NAL C LIP XTP THDMIHDM I