Penning Mixture 1 Penning Mixture

Total Page：16

File Type：pdf, Size：1020Kb

Penning mixture 1 Penning mixture A Penning mixture ((Weston 1968, p. 334), (Bylander 1979, p. 65)), named after Frans Michel Penning, is a mixture of gases used in electric lighting or displaying fixtures. Although the popular phrase for the most common of these is a neon lamp, it is more efficient to have the glass tube filled not with pure neon, but with a Penning mixture, which is defined as a mixture of one inert gas with a minute amount of another gas, one that has lower ionization voltage than the main constituent (or constituents). Explanation The other gas, called a quench gas, has to have lower ionization potential than the first excited state of the noble gas. The energy of the excited noble gas atoms then can ionize the quench gas particles by energy transfer via collisions; known as the Penning effect. A very common Penning mixture of about 98–99.5% of neon with 0.5–2% of argon is used in some neon lamps, especially those rated at 110 volts. The mixture is easier to ionize than either neon or argon alone, and lowers the striking voltage at which the tube becomes conductive and starts producing light. The optimal level of argon is about 0.25%, but some of it gets adsorbed onto the borosilicate glass used for the tubes, so higher concentrations are used to take the losses into account; higher argon content is used in higher-power tubes, as hotter glass adsorbs more argon. The argon changes the color of the "neon light", making it slightly more yellowish. A Penning mixture of neon and argon is also used as a starter gas in sodium vapor lamps, where it is responsible for the faint reddish glow before the sodium emission kicks in. The Penning mixture used in plasma displays is usually helium or neon with small percentage of xenon, at several hundred torr. Penning mixtures with the formulas of argon-xenon, neon-argon, argon-acetylene, and xenon-TMA are used as filler gases in gaseous ionization detectors. Other kinds of Penning mixture include helium-xenon. References • Bylander, E.G. (1979), Electronic Displays, New York: McGraw Hill, ISBN 0-07-009510-8, LCCN 78-31849. • Weston, G.F. (1968), Cold Cathode Glow Discharge Tubes, London: ILIFFE Books Ltd, LCCN 68-135075, Dewey 621.381/51, LCC TK7871.73.W44. Article Sources and Contributors 2 Article Sources and Contributors Penning mixture Source: http://en.wikipedia.org/w/index.php?oldid=544244678 Contributors: GeeJo, Huw Powell, Kaviati, Kellyprice, Koavf, Light current, Moletrouser, Nickds1, OAC, PlantTrees, Shaddack, Sobolewski, Think Fast, Unbitwise, 9 anonymous edits License Creative Commons Attribution-Share Alike 3.0 Unported //creativecommons.org/licenses/by-sa/3.0/.

Copy Link

Recommended publications

Open Access Proceedings Journal of Physics: Conference Series
IOP Conference Series: Earth and Environmental Science PAPER • OPEN ACCESS Development of utilization of electrical lamp for fixed lift net (bagan) in Makassar Strait To cite this article: Sudirman et al 2019 IOP Conf. Ser.: Earth Environ. Sci. 253 012026 View the article online for updates and enhancements. This content was downloaded from IP address 60.205.159.195 on 26/09/2019 at 12:21 MarSave IOP Publishing IOP Conf. Series: Earth and Environmental Science 253 (2019) 012026 doi:10.1088/1755-1315/253/1/012026 Development of utilization of electrical lamp for fixed lift net (bagan) in Makassar Strait Sudirman, Najamuddin, M Palo, Musbir, M Kurnia and A Nelwan Faculty of Marine Science and Fisheries, Universitas Hasanuddin, Makassar 90245, Indonesia Email: [email protected] Abstract. The use of light in some types of fisheries has been one of the most advanced and successful methods to control fish for capture purposes. The use of electrical lamps has been developed as a method of attracting small pelagic fish in Indonesia. Fixed lift nets (bagan tancap) are a fishing gear type categorized as lift nets with fine meshed (0.5 cm mesh size) box-shaped netting, operated using lamps to attract pelagic fish. Several studies on fixed lift nets (bagan) were conducted in Makassar Strait, South Sulawesi, Indonesia from 2012 -2017. These studies used various types of electric lamps, such as halogen lamps, mercury lamps, incandescent lamps and light emitting diodes (LEDs). The fishing process was analysed through on-board observation during fishing operations and interviews with fixed lift net fishermen.
[Show full text]
Accessories & Hardware Contents
Accessories & Hardware Toggles Contents Rockers Part Number Page Pushbuttons AT001s .....................................................................Y4 AT100s .....................................................................Y6 Illuminated PB AT200s .....................................................................Y7 Programmable AT400s .....................................................................Y9 Keylocks AT500s ...................................................................Y14 AT600s ...................................................................Y17 Rotaries AT700s ...................................................................Y19 Slides AT2100s .................................................................Y19 AT3000s .................................................................Y20 Tactiles Tilt AT4000s .................................................................Y23 AT4100s .................................................................Y27 Touch AT9000s .................................................................Y34 Indicators Y Accessories Supplement Y2 www.nkk.com Accessories & Hardware Toggles Rockers Color Codes A Black F Green Pushbuttons B White G Blue C Red H Gray D Amber J Clear E S Illuminated PB Yellow Metallic Silver Programmable Hardware Threading Keylocks Many hardware pieces are available in both metric and inch threading, and in such cases M (metric) and H (inch) are noted in the descriptions. The customer must select threading by placing an M or H after the basic AT
[Show full text]
Monitoring of Surge-Protective Devices in Low-Voltage Power Distribution Systems
Monitoring of Surge-Protective Devices in Low-Voltage Power Distribution Systems James Funke François Martzloff EATON Electrical Surges Happen! Reprinted from Conference Record, Power Quality Exhibition and Conference, Chicago, November 16-18, 2004 Significance Part 7 – Mitigation techniques A review paper on how the industry has developed monitoring method to indicate the “health” of permanently-connected surge-protective devices (SPDs) typically installed at industrial or commercial facilities. These SPDs can be located anywhere in the electrical distribution system. Because these devices are primarily connected in parallel (the so-called “one port” type), failure of the SPD does not necessarily cause any immediately noticeable symptoms for the user. Many of these devices are not inspected once they are installed and the user is not aware of their operating status. Therefore monitoring becomes essential in maintaining the surge protection within the facilities. MONITORING OF SURGE-PROTECTIVE DEVICES IN LOW-VOLTAGE POWER DISTRIBUTION SYSTEMS by James Funke François Martzloff Chief Engineer Principal Eaton/Cutler-Hammer Surges Happen! 1. Introduction Surge-protective devices (SPDs) are installed at most industrial or commercial facilities to protect equipment against transient events. These SPDs can be located anywhere in the electrical distribution system. Because these devices are primarily connected in parallel (the so-called “one port” type), failure of the SPD does not necessarily cause any immediately noticeable symptoms for the user. Many of these devices are not inspected once they are installed and the user is not aware of their operating status. Therefore monitoring becomes essential in maintaining the surge protection within the facilities. There is a lack of thorough information on monitoring of SPDs, especially if looking beyond the visual indicators.
[Show full text]
Neon Sign Board
NEON SIGN BOARD 1. INTRODUCTION The Neon sign board is one of the most popular and attractive media of advertisement widely used by industrial and commercial firms to popularize their products among the general public. The neon sign board that is installed on tall buildings attracts the attention of people even from distant places and hence it is ideally suited for advertisement in busy places like big town and cities. 2. PRODUCTS AND ITS APPLICATION Neon Sign Boards are installed on tall buildings situated in busy areas to grab attention of target audience. It is attractive and appealing advertising boards play a significant role in building brand image in the market. It is available in both customized and standard forms as per the requirements of the client. 3. DESIRED QUALIFICATION FOR PROMOTER The Promoter should have preferably a basic degree in plastic engineering/ processing or a degree/ diploma in engineering / or a degree in chemistry. Experience of at least two to three years in plastic industry is desirable. 4. INDUSRTY OUTLOOK AND TREND Industry outlook for this industry is very encouraging. The increasing demand from industrial and commercial firms, to advertise their product has resulted in high growth of this industry, about 20 to 22% in light of expansion of trade and industry, and investment in economy by foreign players. Trend for this industry appear very positive and profitable. 5. MARKET POTENTIAL AND MARKETING ISSUES, IF ANY With the expansion of trade and industry the competition in every field is growing day by day. After liberalization of economic policy, variety of foreign goods are available everywhere at cheap rates creating tough competition for industrial and consumer goods in the Local market and advertisement has become very essential for the success of any business activity.
[Show full text]
CHICAGO MINIATURE LAMP, INC. Tel: 201-489-8989 • Fax: 201-489-6911 WHERE INNOVATION COMES to LIGHT
Search by Part Number: Search for a Rep/Distributor ● Very economical ● Rugged and long-lived ● Ideal for AC line-voltage and up to 90V DC applications ● Standard and bright models CML Neon Lamps Include: Click for more information • Right Angle Assembly • Indicator Lamps • Circuit Component Lamps Home | Electronics | Automotive | Aviation LED Lighting | Incandescent Products | Halogen Products | Panel Mount Indicators | Neon Lamps What's New | About CML | About SLi | Contact Us | FAQs | Site Map ©2001 Chicago Miniature Lighting, Inc. 147 Central Avenue Hackensack, NJ 07601 Tel: 201.489.8989 Fax: 201.489.6911 Search by Part Number: Search for a Rep/Distributor Neon Lamps -- Right Angle Assembly For more information, click the series name (Adobe Acrobat required). • Neon Application/Tech Notes • Series 5314N1 and 5314N2 PCBoard Mount Neon Home | Electronics | Automotive | Aviation LED Lighting | Incandescent Products | Halogen Products | Panel Mount Indicators | Neon Lamps What's New | About CML | About SLi | Contact Us | FAQs | Site Map ©2001 Chicago Miniature Lighting, Inc. 147 Central Avenue Hackensack, NJ 07601 Tel: 201.489.8989 Fax: 201.489.6911 147 Central Avenue Hackensack, New Jersey 07601 CHICAGO MINIATURE LAMP, INC. Tel: 201-489-8989 • Fax: 201-489-6911 WHERE INNOVATION COMES TO LIGHT Series 5314N1 and 5314N2 PC Board Mounted Neon .250 MAX. .300 .250 MAX. Ø.160 MAX. .130 .130 .190±.060 .020 S TAND-OFF FOR POST CLEANING Lamp Leads .150 (tinned) .100* .015 .250* All dimensions in inches. .450 MAX.* *Note: These dimensions are at the base of holder. Board Mounted Neon Lamp •Easy to mount. •Press-in mounting for accurate location on printed circuit board.
[Show full text]
Neon Application Information
147 Central Avenue Hackensack, New Jersey 07601 CHICAGO MINIATURE LAMP, INC. Tel: 201-489-8989 • Fax: 201-489-6911 WHERE INNOVATION COMES TO LIGHT Neon Application Information Lamp Construction value A1 which is largely determined by the impedance of the The basic construction of neon lamps is shown in figure 1. The external circuit, and the voltage across the neon lamp reduces bulb is made of glass sealed in two areas, the pip and the pinch. to a lower value B, known as the maintaining voltage. Further In the pinch area, the increasing the supply voltage (or reducing the external imped- leads protrude through Neon Lamp Construction ance) increases the lamp current with little change to the main- one end of a glass tube taining voltage until point B1 is reached. Then the maintaining and the glass is heated Gas Pip voltage increases with current to a point C when the neon and pinched about the lamp discharge changes from a glow to an arc and the voltage leads. This holds them in across the lamp drops to a few volts at C . Neon lamps should Glass 1 position and forms a her- Envelope be operated in the range B to B1 which is called the "negative metic seal. The leads are glow" region. B1 to C is the "abnormal glow" region and from made from a special C1 beyond is the "arc" region. Electrodes material known as dumet Pinch A neon lamp operates in the following manner: when the applied which is a low resistance voltage is in excess of the striking voltage, electrons are emitted material consisting of a Leads from the surface of the negative electrode (cathode) and, accel- copper sheath around a erated by the electric field, collide with atoms of gas.
[Show full text]
Neon Application Information
147 Central Avenue Hackensack, New Jersey 07601 CHICAGO MINIATURE LAMP, INC. Tel: 201-489-8989 • Fax: 201-489-6911 WHERE INNOVATION COMES TO LIGHT Neon Application Information Lamp Characteristics end of its useful life. Because the minimum acceptable light output The main characteristics of neon lamps are detailed as follows. value will depend upon the application, it is difficult to quote precise In general, these characteristics are not tightly controlled, as the lifetimes, but values for 50% reduction of initial light output levels prime function of the device is to emit light to act as an indicator. are given in Table 1. Since in most applications the lamp will not be If a tube having a more controlled electrical specification is operating all of the time, the actual life of the lamp in the equipment required for use as a circuit component, a cold cathode diode will be considerably longer than the quoted life. It should also be should be used. noted that because the blackening initially occurs around the sides of the glass bulb, a longer lifetime is usually achieved if the lamp is Light Output: Neon lamps are available from Chicago Miniature end-viewed. Table 1 Lamp in two light output ranges (standard and high brightness). The life expectan- The standard brightness types have a light output of approxi- cies quoted in Table1 Typical Life Expectancies of Neon Lamps Operated from an AC Supply mately .06 lumens per mA, and the high brightness types emit apply to neon lamps Brightness Level Life Expectancy approximately .15 lumens per mA.
[Show full text]
Energy Balance of a High- Pressure Sodium Arc Tube
Energy balance of a high- pressure sodium arc tube H idezoh AKUTSU* and Naoki SAITO** This paper describes in detail the dependence of the energy batance of a high･pressure sodium arc tube on discharge parameters. The total radiation and the thermal conduction loss of the arc tube were estimated by calculating the thermal dissipation loss from the measured wall tem- perature of the tube envelope. The results thus estimated showed a rea- sonable consistency with experimental data on the absolute visible radiant power and the published results by previous authors as well. in the low sodium vapor pressure region, the total radiation Pr (W/cm) is influenced sharply by various discharge parameters, while in the high sodium vapor pressure region (above about 70 to 100 Torr), it is deter- mined mainly by the power input Pin (W/cm) through the linear equation Pr;~~0.80 (Pin-6.7) for a sapphire arc tube. It has been concluded that the high efficacy of a high-pressure sodium lamp stems from the low thermal conduotion loss of its arc tube, as well as its high luminous efficacy of visible radiation. properties of the arc tube. Furthermore, a gen- 1. Introduction eral guidance fcr improving the luminous ef ficacy Knowledge about the energy balance in an arc of a high-pressure sodium lamp is shown. tube of a lamp will offer a foothold not only for understanding the processes occurring in the arc tube also fcr improving its luminous efficacy. The 2. Experimental procedures energy balance of a high-pressure sodium arc tube Fig.
[Show full text]
Experiment 40B 9.6.19
Experiment 40B 9.6.19 LIGHT, ENERGY AND SPECTRA MATERIALS: Hydrogen vapor lamp and power supply, quantitative spectroscopes (4); LED circuit board; adjustable voltage DC power supply; demo AS-13 flame test kit; incandescent light bulb fixture PURPOSE: The purposes of this experiment are: (1) to observe the relationship between wavelength, frequency and energy of light; (2) to observe the emission spectrum of atomic hydrogen and (3) to determine the wavelengths and energies of some of the electronic transitions of the Balmer series for hydrogen. LEARNING OBJECTIVES: By the end of this experiment, the student should be able to demonstrate these proficiencies: 1. Calculate the energy of light from its wavelength. 2. Calculate the energy of light from its frequency. 3. Calculate the wavelengths of light expected for specific electronic transitions of hydrogen. 4. Compare the expected wavelengths of the hydrogen atom to the observed wavelengths. 5. Determine the value of Planck’s constant. DISCUSSION: Much of what we know about the atomic or molecular nature of the world has been obtained by the study of how radiation interacts with matter. When people hear the term “radiation” they commonly think of ionizing radiation associated with nuclear processes. We shall study that in SC112, but now we will focus on the radiation we all use and are exposed to daily; mainly the visible part of the electromagnetic spectrum we call light. Light is a wave phenomenon, characterized by frequency, ν, and wavelength, λ, which are related to each other through the speed of light, c. c = λ ν = 2.998 x 108 m/s (1) Planck showed that the energy of light is related to its frequency, hc E = hν = (2) λ where the proportionality constant, h = 6.626 x 10-34 J s, was named in his honor.
[Show full text]
Core Technology Manual
Appendix 1 Glossary of Terms Agitator A type of mechanical mixing device; used in copiers in the toner supply to keep toner particles separated; also used in the development unit to combine toner and carrier, creating two—component developer. AI Short Protocol Artificial Intelligence Short Protocol reduces the time required for the protocol exchange with a particular terminal by saving the communication parameters and the modem rate used to send the last page of a transmission. These parameters are used for the start of the next transmission to that terminal. Air Knife (or Air The air knife paper separation process uses jets of air to separate sheets of paper for Separation) paper feed. Attenuation After the modem converts data to serial and modulates it, the data passes through an attenuator, which adjusts the TX level. Auger A screw-like mechanical transport device used to move bulk materials in many different applications. It relies on a large screw with deep, wide-pitched threads turning inside a close-fitting cylinder. The threads act like an endless scoop or wedge to lift material from one end of the cylinder to the other. Automatic Document A motorized device that allows automatic feeding, alignment and stacking of multiple Feeder (ADF) originals, greatly improving the overall efficiency of photocopying. 10 March 2004 1 Appendix 1 Glossary of Terms Automatic Document An advanced type of document feeder that can recycle and reverse originals. Handler (ADH) Autorouting When a G3 fax message with a SUB code is received, the machine compares it with the personal codes stored in the machine with e-mail addresses.
[Show full text]
Capacitor Analyzer Solar Model Cb-1-60
WAR DEPARTMENT TECHNICAL MANUAL CAPACITOR ANALYZER SOLAR MODEL CB-1-60 DEPARTMENT 2 FEBRUARY 1945 Generated on 2015-12-10 12:22 GMT / http://hdl.handle.net/2027/uc1.b3245553 Public Domain, Google-digitized / http://www.hathitrust.org/access_use#pd-google WAR DEPARTMENT, WASHINGTON 25, D. C., 2 FEBRUARY 1945. TM 11-2658, Capacitor Analyzer Solar Model CB-1-60, is published for the information and guidance of all concerned. [A. G. 300.7 (9 Sept. 44).] BY ORDER OP THE SECRETARY OF WAR : O. G. MARSHALL, Chief of Staff. OFFICIAL : J. A, ULIO, Major General, The Adjutant General. DISTRIBUTION : AAF(5); AGF(5); ASF (5). (For explanation of symbols see FM 21-6.) Generated on 2015-12-10 12:22 GMT / http://hdl.handle.net/2027/uc1.b3245553 Public Domain, Google-digitized / http://www.hathitrust.org/access_use#pd-google CAPACITOR ANALYZER AND RESISTANCE BRIDGE Models CC 1-60 and CB 1-60 Power Line Connections The Solar Capacitor Analyzer Models CC 1-60 and CB 1-60 are designed for use on 110 volts, 50-60 cycles. They should not be con nected to power lines which supply other voltages or frequencies. To place Analyzer in operation, on the Model CC, remove line cord from packing tube in instrument cover, then plug one end of line cord into the receptacle in back of the cabinet, and connect other end to power line. On the Model CB, one end of the line cord is permanently connected to the instrument. Proceed with measure ments according to instructions described in this manual.
[Show full text]
DESIGN ND CONSTRUCTION of Thyratron STROB05COPE J. A
gNGlNEERlNG i..lBRAK'i V• p. l • DESIGN ND CONSTRUCTION OF THYRaTRON STROB05COPE BY o'n f'l- ,.J.;f J. A. MC INTI RE AND J. B. WHITMORE . A Thesis Submitted to the Graduate Committee For the Degree of MASTER OF SCIENCE in Electrical Engineering Approved: Head of Department--- Dean of Engineering Ch irman, Graduate Committee Virginia Polytechnic Institute 1934 TABLL: OF CONT.l!;NTS Page Preface.. • . • . • . • . • • • . • • • • . • • . • . • • • . • . • . • . 2 I. Introduction . .. ..•.....•....... ....................... 4 II. The Review of Literature •• • ••.••••• • ••••••••••••••••••• 5 A. Types of St robo scopes ••••• • ••••• . ••••••••.••• 5 The New Neon El ectric t r oboscope •••. ••••• . ••••• 6 c. The Thy rat r on Tube as a Str oboscope ••• • ••••••••• 6 III. Drawings of Des i gns A. Thyratr on Tube Str oboscope Circ1.lit •• •••• • ••••• • • 7 B. Outl ine Dimensions of Thyr atron FG- 33 •• •• ••••••• 11 I V. The Investigat i on .. ... .. ... ..... ................ .. 6 A. Object of Investigati on •••••••••••••••••• ••• •••• 6 B. Des i gn and Constructi on of Apparatus •• •••• . ••••• 6 c. The Thyratron Tu be •••.•••••• • •• • ..••••.•.• .•. ••• 12 D. Resul ts ••••••••••••••••••••••••••••• , ••••••••••• 14 v. Di scussion of Re sul ts ••••••••••••••••••••••••••••••••• 15 VI . Conclt.t sion ...•••••••••...••..••..•• . •..•••.•...•.•.••. 15 VII. Su.mm.ary . • • • • • • • • • • • • . • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 16 VI II . Bibliography and Lit erat ure Cited ••••••••••• . ••• . ••••• 16 REF ACE The object of this thesis was to construct a thyratron stroboscope to be used in the Virginia Polytechnic Institute Elec- trical Laboratory and to study the use of the thyratron tube as a stroboscope. The v~iters of this thesis know that nine months is a short time to spend on such a broad subject, but an honest effort has been made and we feel as though much has been E-.
[Show full text]