DOCSLIB.ORG

Membranes for Redox Flow Battery Applications

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Membranes for Redox Flow Battery Applications Membranes 2012, 2, 275-306; doi:10.3390/membranes2020275 OPEN ACCESS membranes ISSN 2077-0375 www.mdpi.com/journal/membranes Review Membranes for Redox Flow Battery Applications Helen Prifti 1, Aishwarya Parasuraman 2, Suminto Winardi 2, Tuti Mariana Lim 2,3* and Maria Skyllas-Kazacos 1,* 1 School of Chemical Engineering, The University of New South Wales, UNSW Sydney, NSW 2052, Australia; E-Mail: [email protected] 2 School of Civil and Environmental Engineering, Nanyang Technological University, Singapore 639798, Singapore; E-Mails: [email protected] (A.P.); [email protected] (S.W.) 3 School of Life Sciences and Chemical Technology, Ngee Ann Polytechnic, Singapore 599489, Singapore * Authors to whom correspondence should be addressed; E-Mails: [email protected] (M.S.K.); [email protected] (T.M.L.); Tel.: +61-2-9385-4335 (M.S.K.); +65-6790-4876 (T.M.L.). Received: 8 May 2012; in revised form: 1 June 2012 / Accepted: 7 June 2012 / Published: 19 June 2012 Abstract: The need for large scale energy storage has become a priority to integrate renewable energy sources into the electricity grid. Redox flow batteries are considered the best option to store electricity from medium to large scale applications. However, the current high cost of redox flow batteries impedes the wide spread adoption of this technology. The membrane is a critical component of redox flow batteries as it determines the performance as well as the economic viability of the batteries. The membrane acts as a separator to prevent cross-mixing of the positive and negative electrolytes, while still allowing the transport of ions to complete the circuit during the passage of current. An ideal membrane should have high ionic conductivity, low water intake and excellent chemical and thermal stability as well as good ionic exchange capacity. Developing a low cost, chemically stable membrane for redox flow cell batteries has been a major focus for many groups around the world in recent years. This paper reviews the research work on membranes for redox flow batteries, in particular for the all-vanadium redox flow battery which has received the most attention. Keywords: energy; redox flow batteries; membrane; stability; ionic conductivity Membranes 2012, 2 276 1. Introduction Concern over environmental degradation and climate change associated with fossil fuel based electricity generation has prompted most countries to restructure their electricity generation and distribution in particular, towards increasing electricity generation from renewable energy sources. Renewable energy is intermittent in nature and thus the electricity generated from this source is not dispatchable, leading to unpredictable matching between supply and demand. Therefore energy storage is needed to prevent blackouts caused by unbalanced supply and demand. Besides, energy storage can also assist the utility planner to bridge the gap between the drops in the rate of electricity generated by renewable energy sources due to cloud cover over photovoltaic panel or reduced wind speed and the ramp up rate of gas powered peaking plants which normally take about 15 minutes to ramp up their power output. There are many types of energy storage technologies including pumped hydro, compressed air, fly-wheels and electrochemical systems such as fuel cells and redox flow batteries. Among these energy storage technologies, redox flow battery is considered the best option for medium to large scale storage owing to an excellent combination of energy efficiency, capital cost and life cycle costs without specific site requirement [1]. Redox flow battery uses two soluble redox couples as electroactive materials to store energy via oxidation and reduction reactions. In a typical set-up, the redox flow battery consists of 2 electrolyte reservoirs from which the electrolytes are circulated by pumps through an electrochemical cell stack comprising of a number of cells connected in series or parallel to enable reaction taking place at inert electrodes. Typically, each cell comprises of anode, cathode and an ion exchange membrane separator to allow diffusion of ions across the membrane while preventing the cross-mixing of the electrolyte solutions from these 2 reservoirs. Figure 1 shows the diagram of a vanadium redox flow battery (VRB). Figure 1. Schematic of a Vanadium redox flow battery (Adapted from [2]). During charging, by applying an external power source at the terminals, the discharged form of the redox species in each half cell electrolyte is converted to the charged form. During discharge, electron flows between the redox species thus converting the chemical energy into electricity. Consequently, the concentration of the active redox species and electrolyte volume will determine the energy capacity of the system while the number of cells in the stack and electrode area will determine the system power. The redox flow battery therefore acts more like a regenerative fuel cell than a conventional battery [3]. Membranes 2012, 2 277 Of all the redox flow batteries developed to date, only the all vanadium redox flow battery developed at the University of New South Wales [3,4] has received the most attention due to its high energy efficiency of over 80% in large installations and a long cycle life. The major issues encountered by other redox flow batteries such as iron/chromium, iron/titanium, polysulfide bromine (also known as Regenesys) redox flow batteries include cross contamination of electrolytes due to different redox couple species used in each half-cell and the lack of development of an ideal membrane. The all vanadium flow battery uses the same vanadium element in both half cells which avoids the problems of cross contamination of the two half-cell electrolytes during long term usage. This helps in reducing the capital and maintenance costs, minimizes waste disposal and provides a greater ease of operation. Other attractive features include the ability to use underground electrolyte storage tanks leading to minimal footprint and temperature fluctuations in extreme climates. Furthermore, the redox flow battery can be recharged either conventionally or with mechanical refueling at a suitable refueling station, making it attractive for electric vehicles applications [2]. The original all-vanadium redox flow battery, also known as Generation 1 (G1) VRB uses a solution of vanadium in sulphuric acid in both half cells with V2+/V3+ redox couple operating in the 2+ + 3+ negative half-cell and the VO /VO2 redox couple in the positive half-cell. During charging, V is 2+ 2+ + reduced to V at the negative electrode while VO is oxidized to VO2 at the positive electrode. These reactions are reversed during cell discharge. The maximum vanadium ion concentration that can be employed for wide temperature range operation is typically 2 M or less [5–9]. This concentration is equivalent to an energy density of around 25 Wh/kg and represents the solubility limit of the V(II) and/or V(III) ions in sulphuric acid supporting electrolyte at temperatures below 5 °C and the stability of the V(V) ions at temperatures above 40 °C [10]. Furthermore, significantly lower electrolyte concentrations are needed in many geographic locations where the climate is more extreme and temperatures go below zero degrees in winter. In such climates, vanadium sulphate concentrations as low as 1 M may be needed to avoid precipitation and this leads to further reduction in overall energy capacity. Recent studies showed the use of a halide supporting electrolyte that allows the preparation of vanadium electrolyte with a concentration of up to 4 M leading to the development of Generation 2 (G2) VRB or the vanadium bromide redox flow battery (V/Br) [4]. The G2 VRB employs a vanadium bromide/chloride mixed electrolyte in both half-cells. Since the bromide/polyhalide couple has a less positive potential than the V (IV)/V (V) couple, the bromide ions will preferentially oxidize at the − − − positive electrode during charging. The positive half-cell thus utilizes the Br /ClBr2 or Cl /BrCl2 redox couple while the negative half-cell utilizes the same V2+/V3+ redox couple reaction, similar to the G1 VRB. Since the same electrolyte are used in both half cells, the G2 V/Br shares all the benefits of the G1 VRB technology, particularly with the fact that cross contamination is eliminated, resulting in solutions having an indefinite life [3]. The additional benefit of G2 VRB is the ability to use electrolytes up to a concentration of 4 M and hence having the potential to double the energy density of the G1 VRB and thus extending its energy storage usage for mobile applications. The G2 VRB can also operate at higher temperature ranges (0–50 °C), thus eliminating the thermal precipitation reaction for V (V) and increasing the solubility limits for the other vanadium ions. More recently, researchers at the Pacific Northwest Laboratories demonstrated a significant increase in energy density and a stable temperature range by utilizing a mixed H2SO4/ HCl supporting electrolyte that can optimize the Membranes 2012, 2 278 solubilities of each of the vanadium oxidation states, allowing up to 2.7 M Vanadium solutions to remain stable over the temperature range of 0–50 °C [11]. Both electrolyte improvements will enable installations in extreme climates such as Northern China, Canada and Scandinavian countries that may not be suitable for the G1 VRB electrolyte. In both G1 and G2 VRB system, the key material is the membrane as it defines the performance and economic viability of the batteries. In fact, membrane is identified as the stumbling block towards commercialization of many redox flow batteries as it can contribute up to 20% to the overall battery system cost. Finding and developing a suitable membrane to provide the right balance between performance and cost has now become a main focus for redox flow cell developers around the world. Extensive research on developing suitable membrane material has been carried out since 2005 and earlier reviews by Li et al.
Load more

Recommended publications
  • A Review on the Effect of Proton Exchange Membranes in Microbial Fuel Cells
    Biofuel Research Journal 1 (2014) 7-15 Review A review on the effect of proton exchange membranes in microbial fuel cells Mostafa Rahimnejad *1, Gholamreza Bakeri1, Ghasem Najafpour1, Mostafa Ghasemi2, Sang-Eun Oh3 1Biotechnology Research Lab., Faculty of Chemical Engineering, Babol University of Technology, Babol, Iran 2Fuel Cell Institute, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor Darul Ehsan, Malaysia 3Department of Biological Environment, Kangwon National University, Chuncheon, Kangwon-do, Republic of Korea HIGHLIGHTS MFC is a novel knowledge that can be used to obtain bioenergy in the form bioelectricity. Transfer of produced electrons to anode is one of the main parts in MFCs. Some MFCs needs artificial electron shuttle in their anaerobic anode compartment. The important goal of MFCs is to reach a suitable power for application in small electrical devices. ARTICLE INFO ABSTRACT Article history: Microorganisms in microbial fuel cells (MFC) liberate electrons while the electron donors are consumed. In the anaerobic Received 3 December 2013 anode compartment, substrates such as carbohydrates are utilized and as a result bioelectricity is produced in the MFC. MFCs Received in revised form 5 January 2014 may be utilized as electricity generators in small devices such as biosensors. MFCs still face practical barriers such as low Accepted 6 January 2014 generated power and current density. Recently, a great deal of attention has been given to MFCs due to their ability to operate Available online 17 February 2014 at mild conditions and using different biodegradable substrates as fuel. The MFC consists of anode and cathode compartments. Active microorganisms are actively catabolized to carbon sources, therefore generating bioelectricity.
    [Show full text]
  • Characterization of Battery for Energy Storage Applications – Lead Acid
    Abstract #1672, 224th ECS Meeting, © 2013 The Electrochemical Society Characterization of battery for energy storage applications curves of a lead acid battery (YUASA, NP4-6). It has a – lead acid battery, lithium battery, vanadium redox normal voltage of 6 V and capacity of 4 Ah. The battery flow battery, and capacitor power was drained at 0.5 A till the cell voltage down to 3.0 V. The E-I curve was recorded by linear scanning Chih-Lung Hsieh1, Yen-Ting Liu2, Kan-Lin Hsueh2, amperometry at scanning rate of 0.01 A/s. The battery is Ju-Shei Hung3 then charge at 0.5 A for 2 hours. The SOC was assumed reached 25%. The E-I curve was then recorded. This 1. Institute of Nuclear Energy Research, Taoyuan, Taiwan procedure was carried out for SOC at 50%, 75%, and 2. Dept. Energy Eng., National United University, Miaoli, 100%. When cell voltage reached 7.0 V during charge Taiwan was considered as 100% SOC. Curves shown on Fig. 2 3. Dept. Chem. Eng., National United University, Miaoli, was measured result of laed acid battery. These curves Taiwan can be described by following equations. Where the IR accounts for internal resistance. Last term of equation [1] is the voltage cahge due to acitvation over-potential. The purpose of this study is to measure the charge/discharge characteristics of four different During Charge components for energy storage application. They are lead RT nF E E 1 iRI o ln o exp[ )]( [1] acid battery, lithium battery, vanadium redox flow battery, nF SO 2 H 4 RT [ 4 [] ] and capacitor.
    [Show full text]
  • Current State and Future Prospects for Electrochemical Energy Storage and Conversion Systems
    energies Review Current State and Future Prospects for Electrochemical Energy Storage and Conversion Systems Qaisar Abbas 1 , Mojtaba Mirzaeian 2,3,*, Michael R.C. Hunt 1, Peter Hall 2 and Rizwan Raza 4 1 Centre for Materials Physics, Department of Physics, Durham University, Durham DH1 3LE, UK; [email protected] (Q.A.); [email protected] (M.R.H.) 2 School of Computing, Engineering and Physical Sciences, University of the West of Scotland, Paisley PA1 2BE, UK; [email protected] 3 Faculty of Chemistry and Chemical Technology, Al-Farabi Kazakh National University, Al-Farabi Avenue, 71, Almaty 050040, Kazakhstan 4 Clean Energy Research Lab (CERL), Department of Physics, COMSATS University Islamabad, Lahore 54000, Pakistan; [email protected] * Correspondence: [email protected] Received: 30 September 2020; Accepted: 26 October 2020; Published: 9 November 2020 Abstract: Electrochemical energy storage and conversion systems such as electrochemical capacitors, batteries and fuel cells are considered as the most important technologies proposing environmentally friendly and sustainable solutions to address rapidly growing global energy demands and environmental concerns. Their commercial applications individually or in combination of two or more devices are based on their distinguishing properties e.g., energy/power densities, cyclability and efficiencies. In this review article, we have discussed some of the major electrochemical energy storage and conversion systems and encapsulated their technological advancement in recent years. Fundamental working principles and material compositions of various components such as electrodes and electrolytes have also been discussed. Furthermore, future challenges and perspectives for the applications of these technologies are discussed.
    [Show full text]
  • Advances in PNNL's Mixed Acid Redox Flow Battery Stack
    Advances in PNNL’s Mixed Acid Redox Flow Battery Stack David Reed, Ed Thomsen, Wei Wang, Zimin Nie, Bin Li, Brian Koeppel, Kurt Recknagle, and Vincent Sprenkle. Pacific Northwest National Laboratory Electrochemical Materials and Systems DOE Office of Electricity Energy Storage Program – Imre Gyuk Program Manager. OE Energy Storage Systems Program Review September 16-19th, 2014 Topics FY 14 Objectives and Goals Background Nafion membrane thickness development. Low cost interdigitated flow design 4 KW stack Conclusion and Future Work FY14 Redox Objectives and Goal Operate at 240 mA/cm2 with improved stack energy efficiency and lower stack pressure drop. Greater stack efficiency Use of 212/211 membrane versus 115. Greater system efficiency Use of interdigitated flow field Understand influence of temperature on stack efficiency Vanadium Mixed Acid Electrolyte 70% increase in capacity 2+ - Charge + Catholyte: VO + Cl + H2O – e Discharge VO2Cl + 2H εco=1.0 V . V2+, V3+, V4+, V5+ stable >2.8M, Anolyte: V3+ + e V2+ ε =-0.25 ao in SO2- and Cl- mixed solutions 2+ - 3+ + 2+ Overall: VO + Cl + H O + V VO Cl + 2H + V Eo=1.25 V 2 2 Power and Energy are separate enabling 80% increase in operating greater flexibility and safety. temperature window. Suitable for wide range of applications 10’s MW to ~ 5 kw . -5 – 50°C Wide range of chemistries available. Low energy density ~ 30 Whr/kg Redox Flow Battery Objectives Develop the technologies, tools, and system understanding required to move the mixed acid electrolyte chemistry from basic chemistry
    [Show full text]
  • Recent Progress in Vanadium Redox-Flow Battery Katsuji Emura1 Sumitomo Electric Industries, Ltd., Osaka, Japan
    Recent Progress in Vanadium Redox-Flow Battery Katsuji Emura1 Sumitomo Electric Industries, Ltd., Osaka, Japan 1. Introduction Vanadium Redox Flow Battery (VRB) is an energy storage system that employs a rechargeable vanadium fuel cell technology. Since 1985, Sumitomo Electric Industries Ltd (SEI) has developed VRB technologies for large-scale energy storage in collaboration with Kansai Electric power Co. In 2001, SEI has developed 3MW VRB system and delivered it to a large liquid crystal display manufacturing plant. The VRB system provides 3MW of power for 1.5 seconds as UPS (Uninterruptible Power Supply) for voltage sag compensation and 1.5MW of power for 1hr as a peak shaver to reduce peak load. The VRB system has successfully compensated for 50 voltage sag events that have occurred since installation up until September 2003. 2. Principle of VRB The unique chemistry of vanadium allows it to be used in both the positive and negative electrolytes. Figure 1 shows a schematic configuration of VRB system. The liquid electrolytes are circulated through the fuel cells in a similar manner to that of hydrogen and oxygen in a hydrogen fuel cell. Similarly, the electrochemical reactions occurring within the cells can produce a current flow in an external circuit, alternatively reversing the current flow results in recharging of the electrolytes. These cell reactions are balanced by a flow of protons or hydrogen ions across the cell through a selective membrane. The selective membrane also serves as a physical barrier keeping the positive and negative vanadium electrolytes separate. Figure 2 shows a cell stack which was manufactured by SEI.
    [Show full text]
  • Alkali Metal Ion-Proton Exchange Equilibria and Water Sorption
    2 Abstract Alkali metal ion - H +exchanges on Nafion 117 membrane treated differently, Dowex 50 W x 4 and Dowex 50 W x 8 resins have been studied at a total ionic strength of 0.1 mol dm-3. The water sorption isotherms of these exchangers in different ionic forms generated over the entire range of water activity, have been analysed by the D’Arcy and Watt equation (DWE). Water sorption studies have shown that the physical structure of the exchangers have changed due to long - storage or aging, resulting in poorer water sorption and even formation of pores in the case of Dowex 50 W x 8 resin. As a result, the counter ions in the exchangers are not hydrated and the water is present in a free form, albeit structured, in the resin phase. The selectivity sequence for the alkali metal ions with reference to the H + (Li+<Na+<K+) for the exchangers used in the present study is in accordance with that reported in the literature for the ionomers having sulphonic acid as the functional group. In view of the absence of hydration of the cations in the resin phase, the driving force for the selectivity of the cation, namely, the net gain in entropy, is expected to come from the loss of structured water during the exchange process. Pre treating the Nafion 117 membrane with boiling acid solution activates the clustered region of the membrane in the H + form, while pretreatment with boiling water expands the non-ionic domain (the region connecting the clusters). These modifications influence the state of water present in the Nafion 117 membrane and the ion exchange equilibria.
    [Show full text]
  • Thermodynamic Equilibrium Constants of Alkali Metal Ion-Hydrogen Ion
    Indian Journal of Chemistry Vol. 31A,June 1992, pp. 317-322 Thermodynamic equilibrium constants of alkali metal ion-hydrogen ion exchanges and related swelling free energies in perfluorosulphonate ionomer membrane (Nafion-117) in aqueous medium Sita T Iyer, Deoki Nandan & R M Iyer" Chemistry Division, Bhabha Atomic Research Centre, Trombav. Bombay 400 085 Li + IH + , Na + IH t , K + IH + , Rb + IH + and Cs + IH + exchange equilibria on a perfluorosulphonate ex- changer (Nafion-1l7) have been investigated at 0.1 M ionic strength in aqueous medium and thermody- namic equilibrium constants of 0.78 to 12.6 (Li + IH t to Cs + IH + ) have been evaluated and the alkali me- tal selectivity sequence has been found to be Cs + > Rh + > K + > Na + > Li ". The various ionic forms of Nafion-1l7 involved have also been subjected to isopiestic water vapour sorption investigations and the hydration numbers and swelling free energies determined. The exchange selectivities have been found to be consistent with the sequence of ionic hydration and swelling free energies, the exchange free energies showing a linear relationship with the difference in free energies of hydration of the exchanging ions as per Eisenman's model. The expanded selectivity as well as swelling free energy ranges observed in Nafion- 117 compared to Dowex SOW type of resins have been interpreted in terms of hydrative and osmotic swelling behaviours of the two exchangers. Existence of a solvent shared ion pair in Nafion-1l7. i.e. - SO; (H20)Cs + observed in an earlier study has been supported
    [Show full text]
  • D520CS/521CS, D2020CS/2021CS Ion Exchange Materials Polymer Dispersions
    Product Bulletin P-14 D520CS/521CS, D2020CS/2021CS Ion Exchange Materials Polymer Dispersions Product Information Nafion™ perfluorosulfonic acid (PFSA) polymer and dispersant compositions. Typical uses include dispersions are made from chemically stabilized PFSA/ fabrication of thin films, coating formulations for fuel cell polytetrafluoroethylene (PTFE) copolymer in the acid membranes, catalyst coatings, sensors, and a variety of (H+) form and are available in several polymer content electrochemical applications. Typical Composition Nafion™ PFSA Polymer Dispersions by Composition Property D520CS D521CS D2020CS D2021CS 5.0 min. 5.0 min. 20.0 min. 20.0 min. Polymer Content, wt% 5.4 max. 5.4 max. 22.0 max. 22.0 max. Water Content, wt% 45 ± 3 45 ± 3 34 ± 2 34 ± 2 VOC Content, wt% 50 ± 3 50 ± 3 46 ± 2 46 ± 2 1-Propanol 48 ± 3 48 ± 3 44 ± 2 44 ± 2 Ethanol <4 <4 <2 <2 Mixed Ethers and Other VOCs <1 <1 <1 <1 Specific Gravity 0.92−0.94 0.92−0.94 1.01−1.03 1.01−1.03 Available Acid Capacity, meq/g, >1.00 >0.92 >1.00 >0.92 H+ polymer basis Total Acid Capacity, meq/g, 1.03−1.12 0.95−1.03 1.03−1.12 0.95−1.03 H+ polymer basis Viscosity, cP, at 25 °C (77 °F) and 10−40 10−40 50−500 50−500 40 sec–1 Shear Rate* *1 cP = 1 MPa·sec Nafion™ Ion Exchange Materials Order Information Handling Practices Dispersions are available in the following containers Ventilation should be provided for safe handling and (4-L minimum order): processing of Nafion™ dispersion.
    [Show full text]
  • PVDF-Modified Nafion Membrane for Improved Performance Of
    membranes Article PVDF-Modified Nafion Membrane for Improved Performance of MFC Liping Fan 1,2,*, Junyi Shi 2 and Yaobin Xi 2 1 College of Information Engineering, Shenyang University of Chemical Technology, Shenyang 110142, China 2 College of Environment and Safety Engineering, Shenyang University of Chemical Technology, Shenyang 110142, China; [email protected] (J.S.); [email protected] (Y.X.) * Correspondence: [email protected] Received: 9 July 2020; Accepted: 12 August 2020; Published: 13 August 2020 Abstract: Low power production and unstable power supply are important bottlenecks restricting the application of microbial fuel cells (MFCs). It is necessary to explore effective methods to improve MFC performance. By using molasses wastewater as fuel, carbon felt as an electrode, and the mixture of K3[Fe(CN)6] and NaCl as a catholyte, an MFC experimental system was set up to study the performance of MFCs with three different proton exchange membranes. A Nafion membrane was used as the basic material, and polyvinylidene fluoride (PVDF) and acetone-modified PVDF were used to modify it, respectively. The experimental results show that a PVDF-modified membrane can improve the water absorption effectively and, thus, make the MFC have greater power generation and better wastewater treatment effect. The acetone-modified PVDF can further improve the stability of output power of the MFC. When the acetone-modified PVDF was used to modify the Nafion membrane, the steady output voltage of the MFC was above 0.21 V, and the Chemical Oxygen Demand (COD) removal rate for molasses wastewater was about 66.7%, which were 96.3% and 75.1% higher than that of the MFC with the ordinary Nafion membrane.
    [Show full text]
  • Battery Technologies for Small Scale Embeded Generation
    Battery Technologies for Small Scale Embedded Generation. by Norman Jackson, South African Energy Storage Association (SAESA) Content Provider – Wikipedia et al Small Scale Embedded Generation - SSEG • SSEG is very much a local South African term for Distributed Generation under 10 Mega Watt. Internationally they refer to: Distributed generation, also distributed energy, on-site generation (OSG) or district/decentralized energy It is electrical generation and storage performed by a variety of small, grid- connected devices referred to as distributed energy resources (DER) Types of Energy storage: • Fossil fuel storage • Thermal • Electrochemical • Mechanical • Brick storage heater • Compressed air energy storage • Cryogenic energy storage (Battery Energy • Fireless locomotive • Liquid nitrogen engine Storage System, • Flywheel energy storage • Eutectic system BESS) • Gravitational potential energy • Ice storage air conditioning • Hydraulic accumulator • Molten salt storage • Flow battery • Pumped-storage • Phase-change material • Rechargeable hydroelectricity • Seasonal thermal energy battery • Electrical, electromagnetic storage • Capacitor • Solar pond • UltraBattery • Supercapacitor • Steam accumulator • Superconducting magnetic • Thermal energy energy storage (SMES, also storage (general) superconducting storage coil) • Chemical • Biological • Biofuels • Glycogen • Hydrated salts • Starch • Hydrogen storage • Hydrogen peroxide • Power to gas • Vanadium pentoxide History of the battery This was a stack of copper and zinc Italian plates,
    [Show full text]
  • 2020 Grid Energy Storage Technology Cost and Performance Assessment
    Energy Storage Grand Challenge Cost and Performance Assessment 2020 December 2020 2020 Grid Energy Storage Technology Cost and Performance Assessment Kendall Mongird, Vilayanur Viswanathan, Jan Alam, Charlie Vartanian, Vincent Sprenkle*, Pacific Northwest National LaBoratory. Richard Baxter, Mustang Prairie Energy * [email protected] Technical Report Publication No. DOE/PA-0204 December 2020 Energy Storage Grand Challenge Cost and Performance Assessment 2020 December 2020 Disclaimer This report was prepared as an account of work sponsored by an agency of the United States government. Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States government. ii Energy Storage Grand Challenge Cost and Performance Assessment 2020 December 2020 Acronyms AC alternating current Ah ampere-hour BESS battery energy storage system BLS U.S. Bureau of Labor Statistics BMS battery management system BOP balance of plant BOS balance of system C&C controls & communication C&I civil and infrastructure CAES compressed-air energy
    [Show full text]
  • Title Synthetic Studies on Perfluorinated Compounds
    View metadata, citation and similar papers at core.ac.uk brought to you by CORE provided by Kyoto University Research Information Repository Synthetic Studies on Perfluorinated Compounds by Direct Title Fluorination( Dissertation_全文 ) Author(s) Okazoe, Takashi Citation Kyoto University (京都大学) Issue Date 2009-01-23 URL http://dx.doi.org/10.14989/doctor.r12290 Right Type Thesis or Dissertation Textversion author Kyoto University Synthetic Studies on Perfluorinated Compounds by Direct Fluorination Takashi Okazoe Contents Chapter I. General Introduction 1 I-1. Historical Background of Organofluorine Chemistry －Industrial Viewpoint－ 2 I-1-1. Incunabula 2 I-1-2. Development with material industry 5 I-1-3. Development of fine chemicals 17 I-2. Methodology for Synthesis of Fluorochemicals 24 I-2-1. Methods used in organofluorine industry 24 I-2-2. Direct fluorination with elemental fluorine 27 I-3. Summary of This Thesis 33 I-4. References 38 Chapter II. A New Route to Perfluoro(Propyl Vinyl Ether) Monomer: Synthesis of Perfluoro(2-propoxypropionyl) Fluoride from Non-fluorinated Compounds 47 II-1. Introduction 48 II-2. Results and Discussion 49 II-3. Conclusions 55 II-4. Experimental 56 II-5. References 60 i Chapter III. A New Route to Perfluorinated Vinyl Ether Monomers: Synthesis of Perfluoro(alkoxyalkanoyl) Fluorides from Non-fluorinated Substrates 63 III-1. Introduction 64 III-2. Results and Discussion 65 III-2-1. Synthesis of PPVE precursors 65 III-2-2. Synthesis of perfluoro(alkoxyalkanoyl) fluorides via perfluorinated mixed esters 69 III-3. Conclusions 75 III-4. Experimental 77 III-5. References 81 Chapter IV. Synthesis of Perfluorinated Carboxylic Acid Membrane Monomers by Liquid-phase Direct Fluorination 83 IV-1.
    [Show full text]