Interposers, Probes and Adapters for Teledyne LeCroy PCI Express® Systems

The Teledyne LeCroy PCI Express Product Line includes a wide variety of probe systems, A Wide designed to reliably capture serial data traffic while minimizing perturbations in the serial data Variety of stream. Probe systems include (a) interposers, designed to capture data traffic crossing a card- connector interface, (b) Mid- probes, designed to capture traffic flowing between components on Bus Probing the same PCB through a special pad designed into the PCB surface, and (c) Multi-lead probes, Options which can be attached directly to exposed traces on the PCB surface. Interposers are typically placed between the PCI Express and the PCI Express card slot on the motherboard. The interposer card plugs directly into the card slot, the expansion card plugs directly into the interposer, and a “tap” is provided for connection to the analyzer in order to capture traffic flowing through the connection. Specialty interposer probes are provided for connectors such as ExpressCard, ExpressModule, AMC and XMC Mezzanine Cards, VPX, Mini Card, CompactPCI Serial, HP Blade Server systems, SFF-8639 modules and M.2 modules. Interposers may be either passive or active: passive interposers simply pass through the PCI Express signals, while active interposers regenerate the signals to ensure reliable communication between the devices with the interposer in place. Mid-bus (both full- and half-size) connect directly to the PCB board through special “header” connections designed into the PCB, and multi-lead probes connect through multiple leads which are Mid-bus directly connected to PCI Express surface traces on the PCB. Probe In all cases, Teledyne LeCroy probing systems are designed to minimize perturbations of the electrical characteristics of the interface, so that test results with the probe in place replicate as closely as possible the system performance without the probe.

Generic Protocol Analyzer Summit Protocol Analyzer Systems Interconnect Diagram This diagram illustrates the three basic methods for introducing a protocol analyzer probe into a PCI Express system. The interposer solution, illustrated on the left side, introduces a card that is plugged into a standard PCI Express slot (or specialty slot), and then the PCI Express card under test is plugged into this interposer. Probe Pod The mid-bus probe solutions are designed for PCI Express data buses which are integrated Customer into a PCB, and allow the probe to tap PCIe Card into the signals through direct attachment via a header pad integrated into the PCB design. The multi-lead cable is connected to pins soldered to exposed Interposer traces to provide access Card to the PCI Express bus.

Full-Size Header Optional Card Reducer Edge Adapter Half-Size Header (if permitted—see interposer description) Customer PCIe Slot Multi-lead Cable 1 Overview of PCIe Probe Systems Interposers Multi-lead Probes Mid-bus Probes

Current Analyzers and Probes Compatible Systems (currently sold) For Details Summit Summit Summit Summit Page Part Number Description T3-16 T3-8 T28 T24 Probes supporting data rates up to 5 GT/s

PE075UIA-X Gen2 x16 Passive Slot Interposer   PE074UIA-X Gen2 x8 Passive Slot Interposer    4 PE073UIA-X Gen2 x4 Passive Slot Interposer     PE072UIA-X Gen2 x1 Passive Slot Interposer    

PE018UIA-X Gen2 Active Slot Interposer (up to x16)   4 PE111UIA-X Gen2 Active Slot Interposer (up to x8) [L1]   PE060UIA-X Gen2 AMC Interposer 5 PE048UIA-X Gen2 XMC Interposer 5 PE070UIA-X Gen2 VPX Interposer 6 PE049UIA-X Gen2 Mini Card Interposer (Mini-to-Mini) 6 PE051UIA-X Gen2 Mini Card Interposer (Mini-to-PCIe) PE055UIA-X Gen2 ExpressCard Interposer 5 PE050UIA-X Gen2 External Cable Interposer 6 PE061UIA-X Gen2 CompactPCI Serial Interposer 5

PE078ACA-X Gen2 x16 Multi-lead Probe Kit   PE083ACA-X Gen2 x8 Multi-lead Probe Kit    9 PE084ACA-X Gen2 x4 Multi-lead Probe Kit     PE085ACA-X Gen2 x1 Multi-lead Probe Kit    

PE072ACA-X Gen2 x8 Mid-bus Probe Kit (Full Size)    8 PE073ACA-X Gen2 x4 Mid-bus Probe Kit (Half Size)    Probes supporting data rates up to 8 GT/s

PE100UIA-X Gen3 x16 Slot Interposer Kit [L1]   PE101UIA-X Gen3 x8 Slot Interposer Kit [L1]   4 PE102UIA-X Gen3 x4 Slot Interposer Kit [L1]   PE103UIA-X Gen3 x1 Slot Interposer Kit [L1]  

PE058UIA-X Gen3 Right 90 Degree Server Interposer   7 PE059UIA-X Gen3 Left 90 Degree Server Interposer  

PE062UIA-X Gen3 x8 ExpressModule Interposer   PE063UIA-X Gen3 x4 ExpressModule Interposer   7 PE064UIA-X Gen3 x1 ExpressModule Interposer  

PE091UIA-X Gen3 SFF-8639 Single Port Interposer [L1]     7 PE088UIA-X Gen3 SFF-8639 Dual Port Interposer [L1]    

PE089UIA-X Gen3 M.2 M/B-M-Type (Socket 3) Interposer     4 PE090UIA-X Gen3 M.2 B/B-M-Type (Socket 2) Interposer    

PE066UIA-X Gen3 Multi-lead Probe Pod   10 PE080UIA-X Gen3 x1 Multi-lead Probe Set  

PE058ACA-X Gen3 x8 Mid-bus Probe Kit (Full Size)   8 PE059ACA-X Gen3 x4 Mid-bus Probe Kit (Half Size)  

Notes: Interposers and probes marked “[L1]“ support testing of PCIe L1 low-power substates (CLKREQ#) and SRIS features. Systems marked ““ use x4-to-x8 Straight iPass cable(s) PE013UCA-X to connect to analyzer. Summit T3-8 analyzers marked “” may be used in x16 applications by using two systems joined with a x16 expansion cable.

2 Overview of PCIe Probe Systems Interposers Multi-lead Probes Mid-bus Probes

Compatible Systems Legacy Analyzers (no longer sold) (legacy systems) For Details Summit PETracer See Page Part Number Description T2-16 ML Probes supporting data rate of 2.5 GT/s 800-0110-00 Gen1 Passive Slot Interposer   PE007UIA-X Gen1 AMC Interposer   PE036UIA-X Gen1 XMC Interposer   PE006UIA-X Gen1 ExpressCard Interposer   PE032UIA-X Gen1 ExpressModule Interposer   PE005ACA-X PETracer Multi-lead Probe   PE001UAA-X Gen1 x8 Mid-bus Probe Kit (Full Size)   PE004ACA-X Gen1 x4 Mid-bus Probe Kit (Half Size)   Probes supporting data rates up to 5 GT/s PE075UIA-X Gen2 x16 Passive Slot Interposer  PE074UIA-X Gen2 x8 Passive Slot Interposer  4 PE073UIA-X Gen2 x4 Passive Slot Interposer  PE072UIA-X Gen2 x1 Passive Slot Interposer  PE018UIA-X Gen2 Active Slot Interposer (up to x16)  4 PE111UIA-X Gen2 Active Slot Interposer (up to x8)  4 PE060UIA-X Gen2 AMC Interposer  5 PE048UIA-X Gen2 XMC Interposer  5 PE070UIA-X Gen2 VPX Interposer  6 PE049UIA-X Gen2 Mini Card Interposer (Mini-to-Mini)  6 PE051UIA-X Gen2 Mini Card Interposer (Mini-to-PCIe) PE055UIA-X Gen2 ExpressCard Interposer  5 PE050UIA-X Gen2 External Cable Interposer  6 PE061UIA-X Gen2 CompactPCI Serial Interposer  5 PE037UIA-X Gen2 HP BladeServer Interposer  6 PE078ACA-X Gen2 x16 Summit Multi-lead Probe  PE083ACA-X Gen2 x8 Summit Multi-lead Probe  9 PE084ACA-X Gen2 x4 Summit Multi-lead Probe  PE085ACA-X Gen2 x1 Summit Multi-lead Probe  PE072ACA-X Gen2 x8 Mid-bus Probe Kit (Full Size)  8 PE073ACA-X Gen2 x4 Mid-bus Probe Kit (Half Size)  Note: Systems marked with ““ use legacy connection cable PE012UCA-X.

Legacy Probes (no longer sold) Compatible Systems Summit Summit Summit Summit Summit PETracer Part Number Description T3-16 T3-8 T28 T24 T2-16 ML Probes supporting data rates up to 5 GT/s PE012UIA-X Gen2 x16 Passive Slot Interposer  PE013UIA-X Gen2 x8 Passive Slot Interposer  PE014UIA-X Gen2 x4 Passive Slot Interposer  PE015UIA-X Gen2 x1 Passive Slot Interposer  PE021UIA-X Gen2 x16 Passive Slot Interposer Kit  PE022UIA-X Gen2 x8 Passive Slot Interposer Kit  PE024UIA-X Gen2 x4 Passive Slot Interposer Kit  PE025UIA-X Gen2 x1 Passive Slot Interposer Kit  PE022ACA-X Gen2 x16 Multi-lead Probe Kit    PE019ACA-X Gen2 x8 Multi-lead Probe Kit    PE010ACA-X Gen2 x4 Multi-lead Probe Set    PE026ACA-X Gen2 x1 Multi-lead Probe Set    PE017ACA-X Gen2 x8 Mid-bus Probe Kit (Full Size)    PE018ACA-X Gen2 x4 Mid-bus Probe Kit (Half Size)   

3 Passive and Active Slot Interposers Interposers Multi-lead Probes Mid-bus Probes

The Gen2 Passive Slot Interposers support lane widths Gen2 Passive Slot Interposer Part Numbers: PE075UIA-X from x1 to x16 at rates of 2.5 GT/s or 5.0 GT/s. PE074UIA-X These cards CANNOT be used with card reducer edge Summit T28 PE073UIA-X adapters, and therefore must be purchased with the Analyzer PE072UIA-X correct card slot width. The four part numbers listed on the left correspond to x16, x8, x4 and x1 respectively. For lane widths up to x8, one iPass Y-cable (PE010UCA-X) is required. For x16 applications, two iPass Y-cables are required. For Summit T24, use iPass Y-Cables PE013UCA-X. 1 m PN: PE010UCA-X For convenience, these products are also sold in kits One cable supports x8 applications, that include the required iPass cables (PE079UIA-X for Two are required for x16 applications. x16, PE078UIA-X for x8, PE077UIA-X for x4, and PE076UIA-X for x1).

Part Numbers: PE018UIA-X (up to x16) The Gen2 Active Slot Interposers are designed for use Gen2 Active Slot Interposer PE111UIA-X (up to x8) with the Summit Analyzers, and support lane widths up to x16 (PE018UIA-X) or up to x8 (PE111UIA-X). For lane widths up to x8, one iPass Y-cable is required Summit T3-16 (PE010UCA-X). For x16 applications, two iPass Y- Analyzer cables are required. For Summit T24, use PE013UCA-X. If you need to install these interposers into a smaller lane width slot, use a card reducer edge adapter (PE002UIA- X, PE003UIA-X, or PE004UIA-X).

iPass Y-Cables For convenience, these products are also sold in kits 1 m PN: PE010UCA-X that include the required iPass cables (PE019UIA-X for x16, PE110UIA-X for x8). One cable supports x8 applications, The PE111UIA-X supports testing of L1 Substates. [L1] Two are required for x16 applications.

Gen3 Slot Interposer Part Numbers: PE100UIA-X The Gen3 Slot Interposers are for use with the Summit T3-16 and T3-8 Analyzers, and supports lane widths to PE101UIA-X x16 (x8 for the Summit T3-8) at data rates of 2.5, 5.0 Summit T3-16 PE102UIA-X and 8 GT/s. The interposer uses Teledyne LeCroy’s Analyzer PE103UIA-X T.A.P.3 technology to ensure complete data capture at Gen3 rates with minimal signal perturbation. These cards CANNOT be used with card reducer edge adapters, and therefore must be purchased in the correct card slot width. The four part numbers listed above correspond to x16, x8, x4 and x1 respectively. For lane widths up to x8, one Y-cable (PE010UCA-X) is iPass Y-Cables required. For x16 applications, two Y-cables are 1 m PN: PE010UCA-X required. For convenience, these products are sold in One cable supports x8 applications, kits that include 1 to 2 iPass cables (as appropriate). Two are required for x16 applications. These interposers support testing of L1 Substates. [L1]

Gen3 M.2 Interposer Part Numbers: PE089UIA-X (NVMe x4) The Gen3 M.2 Interposer is designed for testing SSD modules designed to M.2 specifications. PE089UIA-X is PE090UIA-X (SATA Express x2) designed to support socket 3 memory modules using NMVe x4. PE090UIA-X is designed for socket 2 iPass Y-Cable memory modules using SATA Express x2. 1 m PN: PE010UCA-X Both interposers support M.2 memory modules in SSD Summit T3-8 lengths of 42mm x 22mm, 60mm x 22mm, 80mm x under Analyzer 22mm and 110mm x 22mm. The device under test is test mounted on the interposer, and the cables provide a connection to the host M.2 slot. One iPass Y-cable (PE010UCA-X) is required for Summit T3-16, T3-8 and T28 systems. For Summit T24, (Cables not use a PE013UCA-X iPass x4-to-x8 cable. to scale)

4 Specialty Interposer Systems Interposers Multi-lead Probes Mid-bus Probes

The Gen2 Advanced Mezzanine Card (AMC) Gen2 AMC Interposer Interposer is designed for use with the Summit Part Number: PE060UIA-X Protocol Analyzers, and supports lane widths from x1 up to x8 at data rates of 2.5 GT/s and 5 GT/s. Host System Insert the AMC Card being tested into the interposer, and insert the interposer into the host Card Under Test system. To connect the analyzer, use the PE010UCA-X iPass cable. For Summit T24, use PE013UCA-X iPass Y-Cable 1 m PN: PE010UCA-X Summit T28

The Gen2 Switched Mezzanine Card (XMC) Gen2 XMC Module Interposer Summit Interposer is designed for use with the Summit Part Number: PE048UIA-X T24 Protocol Analyzers, and supports lane widths from x1 to x8 at data rates of 2.5 GT/s and 5 GT/s. Connect the XMC Card being tested into the interposer, and connect the interposer into the host system. iPass Straight x4-to-x8 Cable 1 m PN: PE013UCA-X To connect the analyzer, use the PE010UCA-X iPass cable. For Summit T24, use PE013UCA-X, as shown here. Host System

Card Under Test (plugs into back side)

Gen2 ExpressCard Interposer The Gen2 ExpressCard Interposer is designed Part Number: PE055UIA-X for use with the Summit Family of Protocol Analyzers and supports x1 lane width at data rates of 2.5 GT/s and 5 GT/s. USB Analyzer Host Insert the ExpressCard into the interposer, and (optional) System insert the interposer into the host system. …or… To connect the analyzer, use the PE010UCA-X iPass cable. For Summit T24, use PE013UCA-X. Card Note: The ExpressCard standard supports both Under PCI Express and USB data links, and the Test ExpressCard Interposer makes both channels iPass Y-Cable available. A USB analyzer can also be 1 m PN: PE010UCA-X connected to the interposer to capture USB traffic in combination with the PCI Express analyzer.

The Gen2 CompactPCI Serial Interposer is Gen2 CompactPCI Serial Interposer designed for use with the Summit Family of Part Number: PE061UIA-X Summit T28 Protocol Analyzers, and supports lane widths Analyzer from x1 to x8 at data rates of 2.5 and 5 GT/s. iPass Y-Cable Insert the CompactPCI Serial card being tested 1 m PN: PE010UCA-X into the interposer and insert the interposer into the host system. To connect the Summit analyzer, use the PE010UCA-X iPass Y-Cable. For Summit T24, Host use PE013UCA-X. System

Carrier card inserts into host system

5 Specialty Interposer Systems Interposers Multi-lead Probes Mid-bus Probes

The Gen2 VPX Interposer is designed for use Gen2 VPX Interposer with the Summit Family of Protocol Analyzers Part Number: PE070UIA-X and supports lane widths from x1 to x16 at data rates of 2.5 GT/s and 5 GT/s. Summit T28 iPass Y-Cable Analyzer Insert the VPX Module into the interposer, and 1 m PN: PE010UCA-X insert the interposer into the host system. To connect the analyzer, use the PE010UCA-X cable. For Summit T24, use PE013UCA-X. There are two iPass connectors on the VPX Host Interposer. Connect to the upper connector for System lane widths up to x8, and to both connectors (using two cables) for x16. Carrier card inserts into host system

The HP BladeSystem Interposer is designed for Gen2 HP BladeSystem Interposer use with the Summit T2-16 Protocol Analyzer and Part Number: PE037UIA-X with Mezzanine and Adapter cards designed for the Hewlett-Packard BladeSystem. The Summit T2-16 Interposer supports lane widths up to x8 at data Analyzer rates of 2.5 GT/s or 5 GT/s. Insert the Mezzanine card into the interposer, and insert the interposer into the HPSystem. To connect the analyzer, use the PE010UCA-X 1 meter Y-cable. For Summit T24, use PE013UCA-X. iPass Y-Cable 1 m PN: PE010UCA-X HP BladeSystem Chassis

Gen2 Mini Card Interposer The Gen2 Mini Card Interposer is designed for USB use with the Summit Family of Protocol Part Number: PE049UIA-X (Mini-to-Mini) Analyzer Analyzers. The interposer supports x1 lane PE051UIA-X (Mini-to-PCIe) (optional) widths at data rates of 2.5 GT/s and 5 GT/s. The Mini Card Interposer also provides a connection for a Teledyne LeCroy USB protocol Summit T28 analyzer. Analyzer There are two configurations of the Mini Card Interposers: (1) as an extender board plugged in (via a cable) to a host Mini Card slot (Mini-to-Mini, PE049UIA-X) or (2) with a standard PCI Express iPass Y-Cable slot to connect the Mini Card directly to the slot 1 m PN: PE010UCA-X PCI Express Slot (Mini-to-PCIe, PE051UIA-X, shown here).

The Gen2 External Cable Interposer provides a Gen2 External Cable Interposer simple means to tap into the serial data traffic Part Number: PE050UIA-X between any two system components which are connected using standard iPass cables. Simply connect the host to the interposer “Host” connector, connect the device to the “Device” connector, and then connect the analyzer to the “Analyzer” connector using a PE010UCA-X iPass Y-Cable. For Summit T24, use PE013UCA-X to connect to the analyzer. The External Cable Interposer uses standard Host iPass x8 connectors. If your host and device System use iPass x4 connectors, use the PE013UCA-X iPass Cables to connect to the interposer.

6 Specialty Interposer Systems Interposers Multi-lead Probes Mid-bus Probes

Gen3 90 Degree Server Interposer Summit T3-8 The Gen3 90 Degree Server Interposer is Analyzer designed for use with the Summit T3-16 and T3-8 Part Number: PE058UIA-X (Right) Protocol Analyzers. The interposer is an active PE059UIA-X (Left) slot interposer designed with Teledyne LeCroy’s T.A.P.3 technology, has a 90 degree change in direction (either left or right—select correct part number as shown on the left), and is useful when PCI Express Card testing PCIe cards in enclosed environments, Under Test such as 1U and 2U server enclosures. Insert the interposer into the PCIe slot of the motherboard, then insert the PCIe card into the iPass Y-Cable slot connector on the surface of the board. 1 m PN: PE010UCA-X PCI Express Slot To connect the analyzer, use the PE010UCA-X 1 meter Y-cable.

Gen3 Single Port SFF-8639 Interposer Summit T3-8 Analyzer The Gen3 Single Port SFF-8639 Interposer is designed for use with the Summit Family of Part Numbers: PE091UIA-X [L1] Protocol Analyzers and supports SFF-8639 drives (both 2.5” and 3”) using NVMe, SCSI Express and SATA Express. The product supports lane iPass Y-Cable (1 m) widths up to x4 and data rates up to 8 GT/s. PN: PE010UCA-X Insert the drive into the interposer, and insert the interposer into the host system. To connect the analyzer, use the PE010UCA-X Device iPass cable. For Summit T24, use PE013UCA-X. Under SFF-8639 Test Host Note: There are two analyzer connectors on the System interposer. One is used only for SATA Express, the second supports NVMe and SCSI Express.

Gen3 Dual Port SFF-8639 Interposer Summit T3-8 Analyzer The Gen3 Dual Port SFF-8639 Interposer is designed for use with the Summit Family of [L1] Part Number: PE088UIA-X Protocol Analyzers and supports dual-ported CrossSync Cable SFF-8639 drives (both 2.5” and 3”) using NVMe and SCSI Express. The product supports lane widths up to x2 and data rates up to 8 GT/s. Insert the drive into the interposer, and insert the iPass Y-Cables (1 m) interposer into the host system. PN: PE010UCA-X To connect the analyzers, use the PE010UCA-X iPass cables. For Summit T24, use PE013UCA-X. Device SFF-8639 Under Host Note: Two analyzer ports are provided. To simul- Test System taneously capture traffic on both ports, use two analyzers and connect them with an optional CrossSync cable to provide synchronized traces.

The ExpressModule Interposer is designed for Gen3 ExpressModule Interposer Summit T3-8 use with the Summit T3-16 and T3-8 Protocol Part Numbers: Analyzer Analyzers. The interposer is an active slot PE062UIA-X (x8) interposer designed with Teledyne LeCroy’s 3 PE063UIA-X (x4) T.A.P. technology, and has three configurations, for x8, x4 and x1 ExpressModule configurations. PE064UIA-X (x2) Insert the interposer into the PCIe slot of the iPass Y-Cable motherboard, then insert the PCIe card into the 1 m PN: PE010UCA-X slot connector mounted on the surface of the board. To connect the analyzer, use the PE010UCA-X ExpressModule 1 meter Y-cable. Card Under Test Server Backplane

7 Mid-bus Probe Systems Interposers Multi-lead Probes Mid-bus Probes

Gen2 Mid-bus Probe Kits The Gen2 Mid-bus Probe Kits support lane x8 configuration shown below Part Numbers: widths from x1 to x16 at data rates of 2.5 GT/s PE072ACA-X (x8) and 5.0 GT/s. PE073ACA-X (x4) To prepare a PCB for use with the Gen2 Mid-bus Probe, an attachment pad is designed into the layout, and a retention module is mounted to this Summit T28 Analyzer pad. A header cable attaches from this header to the Mid-bus Probe Pod, and a reference clock iPass Y-Cable (1m) cable (PE014UCA-X) also connects from the PN: PE010UCA-X PCB to the pod. The pod then attaches to the One cable supports Summit analyzer using a iPass Y-cable. up to x8 applications The probe kit part numbers shown on the far left contain appropriate components (cables, pod, Mid-bus Probe Pod etc.) for the specified configuration (x8 or x4). (PE082UIA-X) External power supplies (12V DC) are supplied with both kits, but are only required in the case of One pod supports up the Summit T24 Analyzer. For all other to x8 lanes analyzers, the probe pods receive power from the analyzer via the iPass cable. PE074ACA-X For x16 applications, use the Summit T3-16 or Full-size Mid-bus two Summit T3-8 Analyzers connected together Probe Head with the x16 Expansion Cable. Two pods and two Full-size mid-bus probe heads are required, Retention Module: and the pods attach to the analyzer(s) using two PE076ACA-X Universal iPass Y-Cables. One pod is connected to the PCB using the Ref Clock Cable, and the second is connected to the first using the Daisy Chain PE014UCA-X Ref Clock Cable Clock Cable (PE009UCA-X).

Gen3 Mid-bus Probe Kit The Gen3 Mid-bus Probe is designed for use with Part Number: PE058ACA-X (Full Size) the Summit T3-16 and Summit T3-8 Analyzers, PE059ACA-X (Half Size) and supports lane widths from x1 to x16 at data rates of 2.5 GT/s, 5 GT/s and 8 GT/s. To prepare a PCB for use with the Gen3 Mid-bus Probe, an attachment pad is designed into the iPass Y-Cable layout, and a probe connector is mounted to this PE010UCA-X pad. A probe cable attaches from this connector One cable supports to the PE054UIA-X Gen3 Mid-bus Probe Pod, x8 applications, and a reference clock cable also connects from Two are required for the PCB to the pod. The pod then attaches to x16 applications. the Summit analyzer using an iPass Y-cable (PE010UCA-X). For x16, use two Pods and two probe cable assemblies, plus one reference clock PE055ACA-X cable (to PCB) and one daisy chain cable Gen3 Mid-bus Pod (between pods). x16 Configuration (shown here) uses two One pod supports x8, Pods, cable assemblies, and headers. two are required for x16

PE014UCA-X Ref Clock Cable

Probe Cable PE057ACA-X Full-Size PE056ACA-X Half Size Probe Connector PE047UIA-X Full-Size PE054UIA-X Half Size

8 Multi-lead Probe Systems Interposers Multi-lead Probes Mid-bus Probes

Gen2 Multi-lead Probe Summit T24 in a x4 Configuration Part Numbers: PE085ACA-X for x1 link width The Summit T24 can support up to x4 (for Summit T24, T28, T3-8 or T3-16) link width, and therefore can use just one probe pod. The straight x4-to-x8 PE084ACA-X for x4 link width iPass cable (PE013UCA-X) is used to (for Summit T24, T28, T3-8 or T3-16) connect the analyzer to the probe pod. PE083ACA-X for x8 link width 12V DC (required for Summit T24 only) (for Summit T28, T3-8 or T3-16) PE014UCA-X Ref Clock Cable PE078ACA-X for x16 link width (for Summit T3-16 or two T3-8 systems) The Summit Gen2 Multi-lead Probe is designed for use with all Summit Analyzers. The probe consists of 1 to 4 probe pods which are connected to the analyzer using either iPass Y-Cables or straight x4-to-x8 iPass cables. Each lane requires two Flex Tips, each Flex Tip is connected to the probe pod using two coaxial cables, and each probe pod supports up to x4 link width. The Flex Tips are soldered directly to exposed bus traces located anywhere on the PCB within approximately 40 cm (16”) of the probe pod, and provide a high impedance connection to maintain the signal integrity of the PCI Express bus. Summit T28 in a x4 Configuration The Summit T28 can support up to x8 link width, and Link Width x1 x4 x8 x16 uses one probe pod Part Number(1) 085 084 083 078 for a x4 application. The pod is con- (2) iPass Y-Cable 1(2) 1(2) nected using an PE010UCA-X iPass Y-Cable to separate Straight iPass Cables Upstream signals from 1(2) 1(2) 24 PE013UCA-X Downstream signals. x4 Probe Pods 112 4 PE014UCA-X PE083UIA-X Ref Clock Cable Coax Cables PE036ACA-X 4163264 Flex Tips (470Ω) PE037ACA-X 2 8 16 32 Ref Clock Cable PE014UCA-X 122 4 Daisy Chain Cables PE009UCA-X 112 3

(1) Full part number is PExxxACA-X with the number shown here replacing the “xxx”. (2) For Summit T24, the straight x4-to-x8 iPass Cable (PE013UCA-X) is required but not included in the kit. For all other systems, the iPass Y- Cable (PE010UCA-X) is required but not included in kit. Summit T28 in a x8 Configuration The Summit T28 can support up to x8 link width, and About x16 Configurations uses two probe pods for a x8 application. All PE013UCA-X Upstream signals are connected to one pod, and all For x16 applications, four iPass Cable pods are used (two for Downstream signals to the other. The pods are Upstream signals, two for connected using straight iPass cables. Downstream signals). The PE014UCA-X Ref Clock Cable is connected Ref Clock Cable from the PCB to one pod, and the other pods are connected with Daisy Chain Cables. The pods are PE009UCA-X Daisy Chain Cable connected to the analyzer(s) using One pod is connected to the straight iPass cables. clock on the PCB using a Ref Clock Cable (PE014UCA-X). The second pod is connected to the first using a Daisy Chain Cable (PE009UCA-X)

9 Multi-lead Probe Systems Interposers Multi-lead Probes Mid-bus Probes

Gen3 Multi-lead Probe The Gen3 Multi-lead Probe supports lane PE066UIA-X G3 Multi-lead Probe Pod widths of x1 to x16 at data rates up to 8 GT/s. PE080UIA-X x1 Probe Set The Gen3 Multi-lead Probe consists of one to Multi-lead Probe Pod four probe pods (PE066UIA-X), each of which PE066UIA-X can support up to four x1 probe sets (PE080UIA-X). Each x1 probe set includes two cables to attach to the probe pod, two flexible PE080UIA-X tips and two probe wires to solder to traces on x1 Probe Set the PCB under test. For designs of x4 or less, the connection from the pod to the analyzer is made using an iPass Summit T3-8 Y-cable (PE010UCA-X). For x8 or x16 designs, Analyzer straight iPass cables (PE013UCA-X) are used to connect to multiple probe pods. Analyzer Connection Cables PE010UCA-X (x4 or less) Probe Tip Connection PE013UCA-X (x8 or x16) (solder to exposed trace)

• Ref Clk Cable (PE014UCA-X) between probe pod and DUT is required but not shown in diagram. Required Components for Different Link Widths Link Width x1 x4 x8 x16

Item Part Number Qty Qty Qty Qty

Y-Cable PE010UCA-X 1 1 x4 Probe Pod setup, showing support brackets (included in iPass Cables PE013UCA-X 2 4 Probe Sets) that assist in holding probe tips in place. x4 Probe PE066UIA-X 1 1 2 4 Pods

x1 Probe Sets PE080UIA-X 1 4 8 16

Ref Clock PE014UCA-X 1 (1) 1 (1) 1 (1) 1 (1) Cable Daisy Chain PE009UCA-X 2 (1) 3 (1) Cables

(1)One Ref Clock cable and one Daisy Chain Cable are included with each Probe Pod (PE066UIA-X.

Specifications for Multi-lead and Mid-bus Probes

Gen2 Gen3 Gen2 Gen3 Mid-bus Probe Multi-lead Probe Multi-lead Probe Mid-bus Probe Mid-bus Probe

PE072ACA-X (x8) PE0xxACA-X PE066UIA-X Pod PE058ACA-X (x8 kit) PE073ACA-X (x4) Part Number(s) (see table page 9) PE080UIA-X Probe Sets PE059ACA-X (x4 kit) PE081ACA-X (x4 for T24) Lane Widths x1, x4, x8, x16 x1, x4, x8, x16 x1, x4, x8, x16 x1, x4, x8, x16 2.5 GT/s, 2.5 GT/s, 2.5 GT/s, 2.5 GT/s, Data Rates 5 GT/s 5 GT/s, 8 GT/s 5 GT/s 5 GT/s, 8 GT/s iPass from analyzer iPass from analyzer Power Source iPass from analyzer iPass from analyzer (or ext 12V DC--T24 only) (or ext 12V DC--T24 only) x4-to-x8 iPass x4-to-x8 iPass iPass Y-Cable(s) Analyzer Connector or Y-Cable or Y-Cable iPass Y-Cable(s) (or Straight – T24 only) (see page 9) (see page 10) Pod Required x4 PE083UIA-X x4 PE066UIA-X x8 PE082UIA-X x8 PE054UIA-X

See product datasheets for complete specification information 10 Specifications for Interposers

Interposer Gen2 Gen 2 Gen2 Gen3 Gen2 Gen2 Gen2 Gen2 Probe Express Passive Active Active AMC XMC VPX CompactPCI System Card Serial

PE072UIA-X PE100UIA-X PE018UIA-X (x16) to to PE060UIA-X PE048UIA-X PE055UIA-X PE070UIA-X PE061UIA-X Part Number PE111UIA-x(x8) PE075UIA-X PE103UIA-X

Form Factor PCIe CEM* PCIe CEM* PCIe CEM* Custom Custom Custom Custom Custom

Dimensions 5.75” x 6.6” 6.9” x 8.6” 7.9” x 6.5” 15” x 3.1” 7” x 14” 4.25” x 9” 3.9” x 11.9” 3.9” x 11.9”

x1, x2, x4, x1, x2, x4, x1, x2, x4, x1, x2, x4, x8, Link Width x1, x2, x4, x8 x1, x2, x4, x8 x1 x1, x2, x4, x8 x8, x16 x8, x16 x8, x16 x16

2.5 GT/s 2.5 GT/s 2.5 ,5 2.5 GT/s 2.5 GT/s 2.5 GT/s 2.5 GT/s 2.5 GT/s Data Rates & 5 GT/s & 5 GT/s and 8 GT/s & 5 GT/s & 5 GT/s & 5 GT/s & 5 GT/s & 5 GT/s

12V DC 12V DC 12V DC 12V DC 12V DC 12V DC 12V DC 12V DC Power Source External External External External External External External External

Impedance 85 ohm 85 ohm 85 ohm 85 ohm 85 ohm 85 ohm 85 ohm 85 ohm (Differential)

Analyzer iPass Y-cable iPass Y-cable iPass Y-cable iPass iPass iPass iPass Y-cable iPass Y-cable Connector** (2 for x16) (2 for x16) (2 for x16) Y-cable Y-cable Y-cable

Gen3 Interposer Gen2 Gen3 Gen3 Gen3 Gen2 Gen2 SFF-8639 Gen3 Probe External HP Blade 90 Degree Express SFF-8639 Mini Card Single- M.2 System Cable System Server Module Dual-Port Port

PE062UIA-X PE049UIA-X PE058UIA-X PE089UIA-X Part Number PE036UIA-X PE037UIA-X PE063UIA-X PE091UIA-X PE088UIA-X PE051UIA-X PE059UIA-X PE090UIA-X PE064UIA-X

Form Factor Custom Custom Custom Custom Custom Custom Custom Custom

Dimensions 4” x 5.9” 2.9” x 13.8” 4.5” x 5.3” 3.75” x 6.6” 4.4” x 16.2” 5,6” x 13.4” 5.6” x 13.4” 5.1” x 9.0”

x2 SATA Exp, x2 NVMe & x4 SCSI Exp. Link Width x1, x2, x4, x8 x1, x2, x4, x8 x1, x2, x4, x8 x1, x2, x4, x8 x1, x4, x8 x4 NVMe, & x2 SCSI OR x2 SATA x4 SCSI Exp. Express Exp.

2.5 GT/s 2.5 GT/s 2.5 ,5 2.5, 5 2.5, 5 2.5, 5 2.5, 5 Data Rates 2.5 GT/s & 5 GT/s & 5 GT/s and 8 GT/s and 8 GT/s and 8 GT/s and 8 GT/s and 8 GT/s

12V DC 12V DC 12V DC 12V DC 12V DC 12V DC 12V DC 12V DC Power Source External External External External External External External External

Impedance 85 ohm 85 ohm 85 ohm 85 ohm 85 ohm 85 ohm 85 ohm 85 ohm (Differential)

Analyzer iPass iPass iPass iPass iPass iPass iPass iPass Connector** Y-cable Y-cable Y-cable Y-cable Y-Cable Y-Cable Y-Cable Y-Cable

*Card meets PCIe CEM requirements except for physical dimensions, as noted immediately below. **Summit T24 Systems always use iPass x4-to-x8 cable (PE013UCA-X). All other systems use iPass Y-Cable (PE010UCA-X). See product datasheets for complete specification information.

11 General Purpose Adapters and Extenders

Part Part Product Image Product Image Number Number

ExpressCard to ExpressCard PCI Express Card to EXP2EXP PCIE2EXP Slot Passive Extender ExpressCard Slot Adapter

PCI Express x4 to PCI Express MINI Card to IB2X4 MINI2EXP Infiniband x4 Adapter ExpressCard Slot Adapter

PCI Express x4 PCI Express Edge Connector MINI to PCI Express Slot, IB2X4E MINI2PCIE to Infiniband x4 Passive Adapter Adapter

PCI Express x16 to x1 ExpressCard to PCI Express PEA1621 EXP2PCIE Adapter Slot, Passive

VPX Host Side Adapter PCI Express x16 to x4 PE-VPX-2- PEA1624 (connects VPX Expansion Adapter X16SLOT Card to PCIe Card Slot)

VPX Device Side Adapter PCI Express x16 to x8 PE-X16SLOT- PEA1628 (connects PCIe Expansion Adapter 2-VPX Card to VPX Backplane)

Gen3 SFF-8639 to x4 Slot PCI Express x16, 50 ohm PCI Edxpress Socket PETERMX PE-8639-2- Bus Termination Adapter Adapter, for NVMe x4, x4SLOT-X SCSI Express x2, SATA Express x2

PCI Express Gen3 SFF-8639 x2 Port B to Loop Back Adapter PELOOP- PE-8639BP-2- x4 PCI Express Adapter for (Tx to Rx Bus for Link BACK X2SLOT-X Dual Port Drives Training Verification)

Gen3 M.2 M-Key to x4PCI PCI Express x16 Right Angle Express Slot Adapter, PE-M-2M-2- PEART16A Adapter (A Side Up) supports PCIe x1, x2 and x4 X4SLOT-X (Socket 3)

Gen3 M.2 B-Key to x4PCI PCI Express x16 Right Angle Express Slot Adapter, PE-M-2B-2- PEART16B Adapter (B Side Up) supports PCIe x1 and x2 X2SLOT-X (Socket 2)

1-800-909-7211 Local sales offices are located throughout the world. teledynelecroy.com Visit our website to find the most convenient location.

©2014 Teledyne LeCroy. All rights reserved. Specifications, prices, availability and delivery subject to change without notice. PCIPROBES Product or brand names are trademarks or requested trademarks of their respective holders. 0412