Unit 10. Hydrotreating. Exercises

1 Fill in the gaps with suitable words from the list below the text. Catalytic Hydrotreating Catalytic hydrotreating (HDT) is one of the most important processes in the refining industry. The HDT process is applied to treat a great variety of 1) ______, such as straight-run distillates, vacuum gas oils (fluid catalytic (FCC) feed), atmospheric and vacuum residua, light cycle oil, FCC naphtha, and lube oils. The main differences in the hydrotreating processes of each feed are the 2) ______, type of catalyst, reactor configuration, and reaction system. Depending on the feed and the main objective of the treatment, the process can be called (HDS), as in the case of the HDS of straight-run naphtha, which is used as 3) ______where is the main undesirable heteroatom. For straight-run gas oil, the process is called hydrotreating because, in addition to sulfur removal, aromatic saturation and nitrogen removal are also desired for diesel fuel production. A 4) ______process is used for the removal of vanadium and nickel from heavy oils.

5) ______is removed primarily to reduce the sulfur dioxide (SO2) emissions caused during fuel 6) ______. Removal of sulfur is also desired to have better feed for subsequent processes (e.g., , ). For naphtha HDS it is necessary to remove the total sulfur from the feed down to a few parts per million to prevent 7) ______the noble metal catalysts in the catalytic reforming. For gas oil HDS, the production of ultralow-sulfur diesel (ULSD) requires the use of highly selective 8) ______together with appropriate reaction conditions. During hydrotreating a number of reactions are carried out: 9) ______, by which C – S, C – N or C – C bonds are cleaved, and 10) ______of unsaturated compounds. The reacting conditions of the HDT process vary with the type of feedstock; whereas light oils are easy to desulfurize, the desulfurization of heavy oils is much more difficult. The hydrotreating reactions take place in catalytic reactors at elevated temperatures and pressures, typically in the presence of a catalyst consisting of an 11) ______impregnated with cobalt, nickel, and molybdenum. A typical hydrotreating unit involves the following steps: • Mixing the liquid feed with a stream of 12) ______recycle gas. • Heating the resulting liquid – gas mixture to the desired reaction 13) ______. • Feeding the mixture to the catalytic reactor, where the hydrotreating reactions take place. • Cooling the reaction products and feeding them to a 14) ______. • Sending most of the -rich gas separated from this vessel through an contactor for removal of H2S. • 15) ______the H2S-free hydrogen-rich gas to the reactor. • Sending the liquid from the gas separator vessel through a stripper distillation tower. The bottoms product from the stripper is the final desulfurized liquid 16) ______,

while the overhead (i.e., hydrogen, methane, ethane, H2S, propane, butane, and

some heavier components) is sent to the amine gas treating. Subsequently, the H2S removed and recovered is converted to 17) ______in a unit. gas separator vessel alumina base hydrogen-rich temperature elemental sulfur recycling refinery streams catalyst product combustion poisoning reforming feed hydrodemetallization hydrogenation sulfur operating conditions

1

Unit 10. Hydrotreating. Exercises

2 Fill in the gaps with suitable words from the box.

benzothiophenes heteroatom pellets pores

diffusion rate poisoning heat

1. In the naphtha process, naphtha sulfur must be reduced to less than 0.5 ppm in order to prevent ………………………… of the nickel catalyst in the reactor. 2. Each sulfur-containing molecule has its own hydrogenolysis kinetics that is usually complex because several successive equilibrium stages are involved and these are often controlled by internal ………………………… limitations during refining. 3. One of the more noticeable facets of the hydrodesulfurization process is that the ………………………… of reaction declines markedly with the molecular weight of the feedstock. 4. It is generally accepted that the simpler sulfur compounds (e.g., thiols, R–SH, and sulfides, R–S–R1) are easier to remove from petroleum feedstocks than the more complex cyclic sulfur compounds such as …………………………). 5. Any atom in a crude oil molecule which is neither hydrogen nor carbon is called a ………………………… (sulfur, nitrogen, oxygen, nickel, vanadium, iron, sodium, calcium, and other less common atoms). 6. Hydrotreating is very exothermic. The ………………………… produced by the reactions causes the gas and oil to increase in temperature as they pass down through the catalyst beds. 7. Fixed-bed residuum hydrotreating catalysts are generally small, extruded ………………………… made from an alumina base. 8. As the size of the ………………………… increases, the surface area decreases and so does the catalyst activity.

2