® High-Performance, Polishable, Ultratoopp Self-Leveling Topping for a SP Fine-Aggregate Finish

DESCRIPTION Ultratop SP is a polishable, self-leveling, cementitious topping that provides a fine-aggregate exposed finish. Ultratop SP is engineered for fast-track resurfacing of horizontal wear surfaces.

FEATURES AND BENEFITS • Easily installed from 3/8" to 2" (10 mm to 5 cm) • Quickly hardens within 2 to 3 hours; polishable in as soon as 24 hours • For diamond-polishing guidelines, see the technical bulletin “Polishing Ultratop” in the Concrete Restoration Systems section of MAPEI’s Website. • Available in gray color • Although already extended with coarser aggregates, Ultratop SP can be extended with decorative aggregate up to 1/4" (6 mm) in size, resulting in unlimited finished appearances. or coatings coatings or stains of installation before required Time (23°C) at 73°F set Final (23°C) at 73°F time Flowing Application temperature range Density Mixing ratio APPLICATION PROPERTIES Color state Physical Shelf life before mixing CHARACTERISTICS PRODUCT AND LIFE SHELF begins. work before 24 hours atleast materials all deliver and site on storage heated for Provide storage. and transit in freezing from containers Protect SCAQMD) California’s of #1168 (Rule VOCs humidity relative 50% and (23°C) at 73°F (CAN/CSA-A23.2-8C) C348 –ASTM strength Flexural humidity relative 50% and (23°C) at 73°F (CAN/CSA-A5) C109 –ASTM strength Compressive Tests Laboratory PERFORMANCEPRODUCT PROPERTIES • •  Ultratop

Ultrat Ultrat Ultrat for fast-track resurfacing of interior wear surfaces. wear interior of resurfacing fast-track for The Ultratopthe Ultratop SP 28 days 28 days 28 7 days day 1 Ultratop Polished System with is engineered for fast-track resurfacing as the cementitious topping of of topping cementitious the as resurfacing fast-track for engineered is Polished System. Polished Polished System using Ultratop using SP System Polished

SP SP SP

o o op

p p

® ® ® Ultratop SP Ultratop provides a provides cementitious topping 24 hours 24 hours minutes < 100 minutes 10 to 32°C) (10°C to 90°F 50°F L) kg per (2.10 ft. cu. per lbs. 131.1 About powder of bag (22.7-kg) 50-lb. per water of L) to 3.31 (2.98 qts. U.S. to 3.50 3.15 0 g per L 0 gper MPa) (6.90 psi > 1,000 (41.4 MPa) psi > 6,000 MPa) (30.3 psi > 4,400 MPa) (17.2 psi > 2,500 Results Gray Powder (23°C) at 73°F place well-ventilated and covered in adry, packaging unopened in original, stored when 9 months Mapecrete

™ Protector FF Protector prepared to CSP#3 prepared Concrete substrate Concrete SP Ultratop Primer SN Primer broadcast #16/30 mesh sand mesh #16/30 broadcast thickness thickness mm) (12 1/2" at Coverage thickness thickness mm) (10 3/8" at Coverage Yield (22.7-kg) bag 50-lb. per APPROXIMATE COVERAGE* *  Bag: 50 lbs. (22.7 kg) (22.7 lbs. 50 Bag: PACKAGING Concrete Topping DIVISIONCSI CLASSIFICATIONS Cast-in-Place Concrete Cast-in-Place conditions and setting practices. setting and conditions to substrate according vary may only.purposes Actual jobsite coverage estimating for is shown Coverage ™ full sand sand full polished

10.6 sq. ft. (0.98 m (0.98 ft. sq. 10.6 14.1 sq. ft. (1.31 m (1.31 ft. sq. 14.1 m³) (0.01 ft. cu. 0.44

03 30 00 30 03 00 53 03

2 ) 2 )

PR: 9610 MKT: 21-1744 04/21