INSTALLATION INSTRUCTIONS FOR PART 99-7001 APPLICATIONS See application list inside WIRING & ANTENNA CONNECTIONS (sold separately) Dodge/Eagle/Mitsubishi/Plymouth 1990-2005 Wiring Harness: 99-7001 • 70-1743 • 70-7001 KIT FEATURES • 70-7003 • Single DIN radio provision Antenna Adapter: • Equalizer provision • Not required KIT COMPONENTS TOOLS REQUIRED • A) Radio housing • B) Bracket set #1 • C) Bracket set #2 • D) Bracket set #3 • E) Faceplate • Phillips screwdriver • Cutting tool • F) (2) #6 x 3/4” Phillips flat-head screws • G) Filler bar • H) Equalizer dummy plate • Socket wrench A B C D CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any E F G H installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition. NOTE: Refer to the instructions included with the REV. 8/13/2014 INST99-7001 REV. aftermarket radio. METRA. The World’s best kits.™ 1-800-221-0932 metraonline.com © COPYRIGHT 2004-2014 METRA ELECTRONICS CORPORATION 99-7001 Applications Table of Contents DODGE MITSUBISHI (continued) Dash Disassembly Colt ...................................... 1993-1995 Mirage ................................. 1993-1996 – Dodge Colt/Eagle Summit 1993-1995, Mitsubishi Mirage 1993-1996 .................3 Stealth ................................. 1991-1996 Mirage ................................. 1997-2002 – Dodge Stealth 1991-1996, Mitsubishi 3000GT 1991-1998 ..................................4 Montero ............................... 1992-1996 – Eagle Summit (wagon) 1992-1996, Mitsubishi Expo 1992-1995, EAGLE Montero Sport ...................... 2000-2004 Summit ................................ 1993-1995 Plymouth Colt Vista 1992-1994 ...........................................................................5 Summit (wagon) .................... 1992-1996 PLYMOUTH – Eagle Talon/Mitsubishi Eclipse/Plymouth Laser 1990-1994 .................................6 Talon ................................... 1990-1994 Colt Vista ............................. 1992-1994 – Eagle Talon 1995-1998, Mitsubishi Eclipse 1995-1999 .......................................7 Talon ................................... 1995-1998 Laser .................................. 1990-1994 – Mitsubishi Diamante 1994-1996 .........................................................................8 – Mitsubishi Eclipse 2000-2005 .............................................................................9 MITSUBISHI – Mitsubishi Galant 1994-1998 ............................................................................10 3000GT ............................... 1991-1998 – Mitsubishi Mirage 1997-2002 ...........................................................................11 Diamante ............................. 1994-1996 – Mitsubishi Montero 1992-1996 .........................................................................12 Eclipse ................................. 1990-1994 – Mitsubishi Montero Sport 2000-2004 ...............................................................13 Eclipse ................................. 1995-1999 Eclipse ................................. 2000-2005 Kit Assembly ................................................................................................. 14-17 Expo .................................... 1992-1995 – Single DIN radio provision .................................................................................15 Galant .................................. 1994-1998 – Equalizer provision ............................................................................................15 2 Dash Disassembly 99-7001 Dodge Colt/Eagle Summit 1993-1995, Mitsubishi Mirage 1993-1996 1. Remove (2) Phillips screws below the A/C (1) (3) vents. Pry out on the top of the dash trim bezel and remove the bezel. (Figure A) 2. Remove (4) screws securing the factory radio and disconnect (2) (4) the wiring. (Figure A) 3. Cut and remove mounting tabs “A” and C (Figure C) “B” on the radio housing. Dash trim bezels with a divided radio opening: • If NOT keeping the factory pocket: Cut and remove the upper rib from the radio opening 4. Cut and remove all and snap the filler bar onto the bottom of the radio housing. (Figure C, 1) mounting tabs on • If keeping the factory pocket: Cut and remove the upper rib from the radio opening and bracket set #1 EXCEPT the bottom portion of the radio housing. (Figure C, 2) tabs “C”. (Figure B) Dash trim bezels with an undivided radio opening: Note: Mounting tabs • If NOT keeping the factory pocket: Cut and remove the lower rib from the radio opening are identified by the and the top portion of the radio housing. (Figure C, 3) letter stamped on backs • If keeping the factory pocket: Cut and remove the lower rib from the radio opening, the of each tab. top portion of the radio housing and the bottom portion of the housing. (Figured C, 4) C Continue to kit assembly (Figure B) 3 Dash Disassembly 99-7001 Dodge Stealth 1991-1996, Mitsubishi 3000GT 1991-1998 1. Using a panel removal tool, pry out on the radio (1) (2) (3) trim bezel and remove. (Figure A) 2. Remove (4) screws securing the factory radio and disconnect the wiring. 3. Cut and remove mounting tabs “A” and (Figure A) “B” on the radio housing. (Figure C) E 4. Cut and remove all Dash trim bezels with a divided radio opening: mounting tabs on • If NOT keeping the factory pocket: Cut and remove the upper rib from the radio opening bracket set #2 EXCEPT tabs “E”. (Figure B) and snap the filler bar onto the bottom of the radio housing. (Figure C, 1) Note: Mounting tabs • If keeping the factory pocket: Cut and remove the upper rib from the radio opening and are identified by the the bottom portion of the radio housing. (Figure C, 2) letter stamped on backs Dash trim bezels with an undivided radio opening: of each tab. • Cut and remove the lower rib from the radio opening and the top portion of the radio housing. (Figure C, 3) E Continue to kit assembly (Figure B) 4 Dash Disassembly 99-7001 Eagle Summit (wagon) 1992-1996, Mitsubishi Expo 1992-1995, Plymouth Colt Vista 1992-1994 1. Remove (2) screws from the top edge of the dash (1) (3) trim bezel. Remove the ashtray and (2) screws exposed. Unclip the dash trim bezel and disconnect the cigarette lighter wiring. 2. Remove (4) Phillips screws securing the (2) (4) factory radio and (Figure A) disconnect the wiring. (Figure C) 3. Cut and remove F mounting tabs “A” and Dash trim bezels with a divided radio opening: “B” on the radio housing. • If NOT keeping the factory pocket: Cut and remove the upper rib from the radio opening and snap the filler bar onto the bottom of the radio housing. (Figure C, 1) 4. Cut and remove all mounting tabs on • If keeping the factory pocket: Cut and remove the upper rib from the radio opening and bracket set #2 EXCEPT the bottom portion of the radio housing. (Figure C, 2) tabs “F”. Dash trim bezels with an undivided radio opening: Note: Mounting tabs • If NOT keeping the factory pocket: Cut and remove the lower rib from the radio opening are identified by the and the top portion of the radio housing. (Figure C, 3) letter stamped on backs • If keeping the factory pocket: Cut and remove the lower rib from the radio opening, the of each tab. F top portion of the radio housing and the bottom portion of the housing. (Figured C, 4) Continue to kit assembly (Figure B) 5 Dash Disassembly 99-7001 Eagle Talon/Mitsubishi Eclipse/Plymouth Laser 1990-1994 1. Unclip the radio trim bezel (the factory pocket (1) (2) (3) will be attached). 2. Remove (4) screws securing the factory radio and disconnect the wiring. 3. Cut and remove all mounting tabs on the (Figure A) radio housing EXCEPT (Figure C) tabs “B”. (Figure B) B Dash trim bezels with a divided radio opening: Note: Mounting tabs • If NOT keeping the factory pocket: Cut and remove the upper rib from the radio opening are identified by the and snap the filler bar onto the bottom of the radio housing. (Figure C, 1) letter stamped on backs of each tab. • If keeping the factory pocket: Cut and remove the upper rib from the radio opening and the bottom portion of the radio housing. (Figure C, 2) Dash trim bezels with an undivided radio opening: • Cut and remove the lower rib from the radio opening and the top portion of the radio housing. (Figure C, 3) B Continue to kit assembly (Figure B) 6 Dash Disassembly 99-7001 Eagle Talon 1995-1998, Mitsubishi Eclipse 1995-1999 1. Slide the front seats forward and remove (1) Center console Remove cover cap and (1) Phillips shaded portions screw from each side of the center console. 2. Unsnap the cupholder/ ashtray assembly and remove (2) Phillips Radio trim bezel screws exposed. 3. Unclip the radio trim (Figure A) bezel and remove (2) Keep “G” tabs Phillips screws exposed. B (Figure A) (Figure C) 4. Unscrew the shifter Cut and remove knob. Disconnect the 6. Cut and remove mounting tabs “A” and “B” on the radio housing. Cut and remove the cigarette lighter and lower rib from the radio opening. (Figure B) light wiring. Lift up on the center console 7. Cut and remove all mounting tabs on backet set #2 EXCEPT tabs “G”. (Figure C) A and remove. Note: Mounting tabs are identified by the letter stamped on backs of each tab. 5. Remove (4) Phillips 8. Once the mounting tabs are removed, cut and remove the SHADED portions of the screws securing the brackets. (Figure C) factory radio and B disconnect the wiring. Continue to kit assembly (Figure B) 7 Dash Disassembly 99-7001 Mitsubishi Diamante 1994-1996 1. Remove