Adaptive Optics for Eso's Very Large Telescope (Vlt) Project

Total Page:16

File Type:pdf, Size:1020Kb

Adaptive Optics for Eso's Very Large Telescope (Vlt) Project ADAPTIVE OPTICS FOR ESO'S VERY LARGE TELESCOPE (VLT) PROJECT Fritz Merkle European Southern Observatory Karl-Schwarzschild-Str. 2 D-8046 Garching Fed. Rep. Germany May 1986 VLT REPORT No. 47 ADAPTIVE OPTICS FOR ESO'S VERY LARGE TELESCOPE (VLT) PROJECT Fritz Merkle Abstract Imaging in ground-based astronomy is limited by the transmission of the light through the turbulent atmosphere. Adaptive optics offers the possibility to overcome these limitations. It employs a real-time phase compensation with a phase shifting optical element, which is usually a deformable mirror. The information for the control of the mirror surface is gained from a wavefront sensor. This report describes the principles of adaptive optics and its application in astronomy. It gives an overview over the major elements like the wavefront correction devices, the wavefront sensors, and control systems. The performance of adaptive systems and the requirements in astronomy are discussed and guidelines for the implementation of this technology in ESO's Very Large Telescope given. Table of Contents 1 Introduction 1 2 Principles of Adaptive Optics 4 3 Adaptive Optics in Astronomy 9 4 Strategy for Seeing Optimization 10 5 Elements of an Adaptive System 14 5.1 Wavefront Correction Device 14 5.2 Wavefront Sensor 17 5.2.1 Shearing-Interferometer 17 5.2.2 Shack-Hartmann Sensor 19 5.3 Control System 22 6 Performance of an Adaptive System 22 7 Requirements for Adaptive Correction in Astronomy 24 8 Adaptive Optics for the VLT 28 9 Conclusion 31 References 32 1 1 Introduction A perfect astronomical telescope should have a theoretical angular resolu­ tion of A ~a = 1.22 D (in Radians) (A: wavelength, D: telescope diameter), where ~a is the radius of the first dark ring of the Airy disc. This would lead to the resolution values dis­ played in figure 1 for different telescope diameters. However, in practice the imaging quality of ground-based telescopes is degraded by the transmission of the light from the astronomical object through the turbulent atmosphere of the earth. The reason for this degradation is a random spatial and tem­ poral wavefront perturbation induced by the turbulences in the different layers of the atmosphere. In addition to this, also the aberrations of the optical elements of the telescope contribute to the degradation. All these .... ..u III u ....... t c: ~ 10-2 +,t-,'-+-'1f---/+-+----+------l ::::J C III ...QI ... IV ~ 10-3+--+/-+-----1---+-----( c: IV 10- 4 L----t---+---t----' 0.1 1 10 100 1000 [/Lm] Wavelength - Figure 1: Angular resolution of an astronomical tf']pscope in the absence of any atmospheric and instrumental distortion of the light transmission (The angular resolution is given as radius of the. first dark ring in the Airy disc.) 2 1 INTRODUCTION wavefront perturbations together result in a complex phase aberration <P(r, t) - z'A(r, t) of the light beam. The real part <P(r, t) represents the phase shift of the wavefront, usually called"seeing" , while the imaginary part A( r, t) is a mea­ sure for the intensity fluctuations across the aperture plane, called "scintil­ lation". Figure 2 displays the influence of phase distortions on the image quality, which is commonly described with the Strehl ratio S: S = peak z'rradz'ance z'n the j oeaL pLane peak z'rradz'ance dz'j jractz'on hm£ted o t= « ex: 0.5 ...J :I: w ex: ~ VI O'--------I--- L----.J o 0.05 01 RMS ERROR [wave~ Figure 2: Image quality vs. the RMS wavefront error. The image quality is given by the Strehl ratio S. It is possible to correct the phase shift with a technique called adaptive optics [Hardy 1978, Pearson 1979, Merkle 1983a). The basic principle of adaptive optics is to use a phase shifting optical element, which can be controlled in space and time in order to compensate the atmospheric phase shift (see fig.ure 3). A correction of the scintillation would require a spatially and temporally controllable apodization element. Thus, a system for the fu 11 correction of the aberrations applies a compensation equal to -<P(r, t) + z'J.tA{r, t) 3 WAVEFRONT CONTROL OBJECT IMAGE WAVEFRONT SENSOR CONTROL SYSTEM Figure 3: Principle of active/adaptive optical correction system. (J.L : dimensionless intensity scaling factor). For most of the imaging prob­ lems, especially with very large telescopes, the phase correction part is sufficient and for technical reasons its realization is much easier than the correction of the intensity fluctuations. The field of adaptive optics is in astronomy often divided [Woolf 1984] in the so-called "active optics': which is used for the figure correction of the telescope optics and the "adaptive optics" for the correction of atmospheric effects. In this definition the field of active optics is just a special case of the general principle of adaptive optics at low spatial and temporal frequencies. However, in optical and control engineering the distinction is different. Here, active optical systems or the active components thereof are capable of reshaping a wavefront by adding a set of controllable path differences. No closed loop servo control that operates on the actual wavefront error information is present. An adaptive optical system includes a closed loop phase error sensor that acts to drive a set of path differences to zero. Therefore, the terminology used in astronomy is in some sens contradictory to the technical definition but useful to identify the different applications, mainly because the ways of their technical realization are quite different. The scope of this paper is the field of adaptive optics for atmospheric turbulence correction. During the last 10 years the techniques of adaptive optics have been developed, mainly for laser beam transmission through the turbulent at­ mosphere. Although most of the developments have been made in the United Sta.tes (at companies like ITEK, Lockheed, United Technologies, AVCO Everett, The Aerospace Corp., AOA, and others), there are some promising activities in Europe (CGE, ONERA (France), MBB, and Diehl 4 2 PRINCIPLE OF ADAPTIVE OPTICS (FRG)). The transfer of these techniques to the astronomical field is not straight forward, mainly because of the very low light levels compared with laser applications and the large apertures of the astronomical telescopes. However, the progress in wavefront-sensor technology and the availability of fast computers to cope with the large number of corrections at large aper­ tures has opened the technical feasibility of adaptive optics to astronomy. New ideas came up to overcome the intensity problems, like shooting laser beams to the higher atmosphere to create an artificial star-like reference sources. The intention of this report is to introduce the techniques of adaptive optics and its implication to astronomy. The chapters 2 and 3 will give an introduction to principles of adaptive optics. Chapter 4 describes correction strategies and chapter 5 the the basic elements of an adaptive system. The performance of an adaptive system is evaluated in chapter 6. Chapter 7 and 8 describe the requirements for the design of an adaptive system in astronomy and, especially, with respect to ESO's Very Large Telescope (VLT) project. 2 Principle of Adaptive Optics An adaptive optical system (see figure 4) contains four basic elements: an optical train and image detector, a wavefront sensor, a servo-control system, and a phase-shifting optical element. The distortion of the received wave­ front is usually compensated by reflecting the light beam on a deformable mirror. The surface of this mirror is adjusted in real-time to compensate the path length aberrations. The information required to deform the mirror is obtained by analyzing the light beam with a wavefront sensor. A map of wavefront errors is then derived at each instant of time. Using this error map. the control system determines the signals required to drive the phase shifting optical element and to null the phase aberrations by closing the adaptive loop. The phase correction values can be obtained by expanding the phase-correction function N <l> (r, t) = L an (t) f n(7'1 n=l in a spatially (fn(r)) and temporally (an(t)) dependent function. The spa­ tial functions might represent zones or mode of the aperture, resulting in a zonal or modal correction strategy. 5 LIGHT FROM THE TELESCOPE CLOSED LOOP (- ~-t=I""L I CONTROL SYSTEM I I ~ I I I I I I WAVEFRONT l_ SENSOR Figure 4: Principle of the application of adaptive optics in astronomy. The complexity and design of an adaptive system depends of the aper­ ture size D of the telescope, the direction of the optical path specified by the zenith angle, and the atmospheric conditions. The atmospheric condi­ tions are usually described with the atmospheric turbulent refractive-index structure constant C~ [see Roddier 19811 which is a function of the height h above the ground. Figure 5 (left) shows a model of the vertical profile of the C~ distribution of as a function of altitude h for day and night time [Fried 1982~ and some measurements of C~ in Europe [Barletti 1976, (right). The resulting seeing conditions are often characterized by the scaling parameter 2 TO = [0.423k ~ C~(h) dh] -3/5 with 7r k = 2- >. (A: wavelength, R: height of the atmosphere) called atmospheric corre­ leation length or coherence diameter. It was introduced by Fried in 1965 [Fried 1965]. The size of the resulting seeing disc is then in the order of A/TO' 6 2 PRINCIPLE OF ADAPTIVE OPTICS , ::" IE-13 10- 1 ~ N < u 1E-'" 10- 1, Cl: W c~ (Z), t- W ~2Il I: . 1~-15 < 10- 1, Cl: < 0.. w Cl: lE-le "AVG" -, :0 10.
Recommended publications
  • The European Southern Observatory Your Talk
    The European Southern Observatory Your talk Your name Overview What is astronomy? ESO history What is ESO? La Silla VLT ALMA E-ELT ESO Visitor Centre | 9 October 2013 Why are we here? What is astronomy? And what it all is good for? ESO Visitor Centre | 9 October 2013 What is astronomy? Astronomy is the study of all celestial objects. It is the study of almost every property of the Universe from stars, planets and comets to the largest cosmological structures and phenomena; across the entire electromagnetic spectrum and more. It is the study of all that has been, all there is and all that there ever will be. From the effects of the smallest atoms to the appearance of the Universe on the largest scales. ESO Visitor Centre | 9 October 2013 Astronomy in the ancient world Astronomy is the oldest of the natural sciences, dating back to antiquity, with its origins in the religious, mythological, and astrological practices of the ancient civilisations. Early astronomy involved observing the regular patterns of the motions of visible celestial objects, especially the Sun, Moon, stars and naked eye observations of the planets. The changing position of the Sun along the horizon or the changing appearances of stars in the course of the year was used to establish agricultural or ritual calendars. ESO Visitor Centre | 9 October 2013 Astronomy in the ancient world Australian Aboriginals belong to the oldest continuous culture in the world, stretching back some 50 000 years… It is said that they were the first astronomers. “Emu in the sky” at Kuringai National Park, Sydney -Circa unknown ESO Visitor Centre | 9 October 2013 Astronomy in the ancient world Goseck Circle Mnajdra Temple Complex c.
    [Show full text]
  • 8. Adaptive Optics 299
    8. Adaptive Optics 299 8.1 Introduction Adaptive Optics is absolutely essential for OWL, to concentrate the light for spectroscopy and imaging and to reach the diffraction limit on-axis or over an extended FoV. In this section we present a progressive implementation plan based on three generation of Adaptive Optics systems and, to the possible extent, the corresponding expected performance. The 1st generation AO − Single Conjugate, Ground Layer, and distributed Multi-object AO − is essentially based on Natural Guide Stars (NGSs) and makes use of the M6 Adaptive Mirror included in the Telescope optical path. The 2nd generation AO is also based on NGSs but includes a second deformable mirror (M5) conjugated at 7-8 km – Multi-Conjugate Adaptive Optics − or a post focus mirror conjugated to the telescope pupil with a much higher density of actuators -tweeter- in the case of EPICS. The 3rd generation AO makes use of single or multiple Laser Guide Stars, preferably Sodium LGSs, and should provide higher sky coverage, better Strehl ratio and correction at shorter wavelengths. More emphasis in the future will be given to the LGS assisted AO systems after having studied, simulated and demonstrated the feasibility of the proposed concepts. The performance presented for the AO systems is based on advances from today's technology in areas where we feel confident that such advances will occur (e.g. the sizes of the deformable mirrors). Even better performance could be achieved if other technologies advance at the same rate as in the past (e.g. the density of actuators for deformable mirrors).
    [Show full text]
  • Position Sensing in Adaptive Optics
    Position sensing in Adaptive Optics Christopher Saunter Durham University Centre for Advanced Instrumentation Durham Smart Imaging Durham Smart Imaging Active Opt ics Adappptive Optics Durham Smart Imaging Active Optics • Relaxing the mechanical rigidity of a telescope support structure • CiihillidiCompensating with actively aligned mirrors • Massive weight and cost savings over a rigid bodyyp telescope – the onlyyp practical wa y of building ELTs. • Slow – 1Hz or less Durham Smart Imaging Active Optics Sensing • Live sensing from starlight • Live sensing from a calibration source • Pre-generated look-up table of distortion vs. ppgg,pointing angle, temperature etc • CitiCritica lfl for segmen te d m irror te lescopes Durham Smart Imaging Active Optics Image credit: Robert Wagner / MAGIC / http://wwwmagic.mppmu.mpg.de/ Durham Smart Imaging Active Opt ics Adappptive Optics Durham Smart Imaging Adaptive Optics An AO system measures dynamic turbulence with a wavefront sensor and corrects it with a deformable mirror or spatial light modltdulator Durham Smart Imaging Applications of AO • Astronomy – AO is fully integral to current VLTs and future ELTs • Ophthalmology – Retinal imaging, measuring distortions • High power lasers – Intra-cavity wavefront shaping. e.g. Vulcan fusion laser (ICF) • Optical drive pickups • Microscopy • Free space optical communication • Military Durham Smart Imaging Wavefront sensors • There are many types of wavefront sensors • Shack Hartmann, Curvature, Pyramid, Point Diffraction Interferometer, Lateral Shearing
    [Show full text]
  • Design and Manufacture of Mirrors, and Active Optics Buddy Martin
    Design and manufacture of mirrors, and active optics Buddy Martin Steward Observatory Mirror Lab 1 Outline • What makes a good mirror? • Modern mirror concepts – thin solid mirrors – segmented mirrors – lightweight mirrors • Honeycomb mirrors – design – casting • Optical manufacture – requirements – aside on active optics and model fitting – fabrication • machining • polishing – measurement • interferometry • null correctors • GMT measurements 2 What makes a good mirror? (mechanical) • Fundamental requirement is to deliver a good wavefront to focal plane in almost all conditions. – Hold its shape to a fraction of a wavelength on large scales – Be smooth to a small fraction of a wavelength on small scales – Contribute little to local seeing (temperature gradients in air) • Stiffness against wind: bending stiffness ∝ Et3 – E = Young’s modulus, t = thickness • Stiffness against gravity: bending stiffness ∝ Et 2 / ρ – This puts a premium on low mass. cross-section of an 8.4 m honeycomb mirror for the Giant Magellan Telescope 3 What makes a good mirror? (thermal) • Thermal distortion: displacement = α ΔT t for “swelling” curvature = α ΔT / t for bending – α = thermal expansion coefficient, ΔT = temperature variation within mirror • “Mirror seeing” ∝ T − T a ir ≈ dTair dt ⋅τ – dTair/dt = rate of change of air temperature 2 – τ = mirror’s thermal time constant ∝ cρt / k • c = specific heat, k = thermal conductivity, t = thickness – Becomes a problem for T - Tair > ~0.3 K, τ > ~1 hr – For glass or glass-ceramics, want t < 5 cm • Bottom line: Mirror should be stiff & light, have low thermal expansion & short thermal time constant. 4 Optical telescopes 12 LBT 10 Keck VLT (4), Gemini (2), Subaru 8 MMT, Magellan (2) 6 Palomar 200 inch diameter (m) diameter 4 Mt.
    [Show full text]
  • Download Chapter 3 Sample Pages
    eyesskies_95.indd 553 2008-07-08 12:24:18 TECHNOLOGY TO 3 THE RESCUE ESO’S NEW TECHNOLOGY Progress in telescopic astronomy would have come to a grinding TELESCOPE The octagonal enclosure housing the European halt in the second half of the twentieth century if it weren’t for the Southern Observatory’s 3.6-metre New Technology digital revolution. Powerful computers have enabled a wealth of Telescope (NTT) at Cerro La Silla in northern Chile was a technological breakthrough new technologies that have resulted in the construction of giant when completed in 1989. The telescope chamber is venti- telescopes, perched on high mountaintops with monolithic or lated by a system of fl aps that makes the air fl ow smoothly segmented mirrors as large as swimming pools. Astronomers across the mirror, resulting in very sharp images. The NTT was also a testbed for have even devised clever ways of undoing the distorting effects fully computer-controlled alt-azimuth mounts, thin of atmospheric turbulence and of combining individual telescope mirrors, and active optics. mirrors into virtual behemoths with unsurpassed eyesight. The optical wizardry of 21st century telescope building has ushered in a completely new era of ground-based astronomical discovery. 45 eyesskies_95.indd 545 2008-07-08 12:23:26 “ Just as modern cars don’t look like Model T-Fords, current telescopes look very different from traditional instruments” THE NEW TECHNOLOGY Just as modern cars don’t look like Model T-Fords, current telescopes look very differ- TELESCOPE PEERS INTO A ent from traditional instruments like the 5-metre Hale Telescope.
    [Show full text]
  • Adaptive Optics Facility – Control Strategy and First On-Sky Results of the Acquisition Sequence
    Adaptive Optics Facility – control strategy and first on-sky results of the acquisition sequence P-Y Madec1, J. Kolb, S. Oberti, J. Paufique, P. La Penna, W. Hackenberg, H. Kuntschner, J. Argomedo, M. Kiekebusch, R. Donaldson, M. Suarez, R. Arsenault European Southern Observatory, Karl Schwarzschild Str 2, D-85748 Garching ABSTRACT The Adaptive Optics Facility is an ESO project aiming at converting Yepun, one of the four 8m telescopes in Paranal, into an adaptive telescope. This is done by replacing the current conventional secondary mirror of Yepun by a Deformable Secondary Mirror (DSM) and attaching four Laser Guide Star (LGS) Units to its centerpiece. In the meantime, two Adaptive Optics (AO) modules have been developed incorporating each four LGS WaveFront Sensors (WFS) and one tip- tilt sensor used to control the DSM at 1 kHz frame rate. The four LGS Units and one AO module (GRAAL) have already been assembled on Yepun. Besides the technological challenge itself, one critical area of AOF is the AO control strategy and its link with the telescope control, including Active Optics used to shape M1. Another challenge is the request to minimize the overhead due to AOF during the acquisition phase of the observation. This paper presents the control strategy of the AOF. The current control of the telescope is first recalled, and then the way the AO control makes the link with the Active Optics is detailed. Lab results are used to illustrate the expected performance. Finally, the overall AOF acquisition sequence is presented as well as first results obtained on sky with GRAAL.
    [Show full text]
  • Active Optics in Astronomy – Modeling of Deformable Substrates : Freeform Surfaces for Fireball and MESSIER
    Proc. 7th Intl. Conf. on Mathematical Modeling in Physical Sciences, ICM2, State University Lomonosov, Moscow, 27-31 Aug. 2018 and, Special Issue of “Journal of the Mechanical Behavior of Materials”, De Gruyter edit., Berlin, accepted 14 Nov. 2018 Active optics in astronomy – Modeling of deformable substrates : Freeform surfaces for FIREBall and MESSIER Gerard R. Lemaitre Laboratoire d’Astrophysique Marseille - LAM, Aix Marseille Université - AMU 38 rue Fr´ed´eric Joliot-Curie, 13388 Marseille CX 13, FRANCE E-mail: [email protected] Abstract: Active optics techniques on large telescopes and astronomical instrumentations provide high imaging quality. For ground-based astronomy, the co-addition of adaptive optics again increases angular resolution up to provide diffraction-limited imaging at least in the infrared. Active and adaptive optics marked milestone progress in the detection of exoplanets, super-massive black holes, and large scale structure of galaxies. This paper is dedicated to highly deformable active optics that can generate non-axisymmetric aspheric surfaces - or freeform surfaces - by use of a minimum number of actuators: a single uniform load acts over the surface of a vase-form substrate whilst under reaction to its elliptical perimeter ring. Two such instruments are presented, 1) the FIREBall telescope and MOS where the freeform reflective diffraction grating is generated by replication of a deformable master grating, and 2) the MESSIER wide-field low-central-obstruction TMA telescope proposal where the freeform mirror is generated by stress figuring and elastic relaxation. Freeform surfaces were obtained by plane super-polishing. Preliminary analysis required use of the optics theory of 3rd-order aberrations and elasticity theory of thin elliptical plates.
    [Show full text]
  • The Extremely Large Telescope Why Chile?
    The Extremely Large Telescope Why Chile? Excellent conditions in the Atacama Desert Extremely dry 90% clean sky Low turbulence Excellent vision to the Southern Hemisphere (Paranal) (Chajnantor) Poor site Chile Armazones and Paranal 25 km Huge Collecting Area HST 2.4m (in space) Gemini N Keck I-II Subaru LBT Gemini S VLTs Magellan GTC HET E-ELT SALT 39m 1990 2000 2010 2020 High quality images from the ground E-ELT excels in collecting power and angular resolution 39.3m telescope with Adaptive Optics will deliver E8m-ELT Hubble Space Telescope 4.9 X better angular resolution (1/D) 510 X faster exposure time (1/D4) than existing 8m telescopes Unprecedented sensitivity and angular resolution Prepare for the unexpected…!! 5 Science • The High-redshift Universe & Galaxy Formation • Black Holes and Active Galactic Nuclei • Resolved Stellar Populations and Star Formation • Exoplanets and their Atmospheres 6 The E-ELT Design • 40-m class telescope: largest optical-infrared telescope in the world • Segmented primary mirror • Active optics to maintain collimation and mirror figure • Adaptive optics assisted telescope • Diffraction limited performance • Wide field of view: 10 arcmin 5-Mirror Design 8 The Main Structure The Main Structure is about 38 m diameter 2500 tonnes of steel moving 700 tonnes of opto-mechanics and electronics around two 65 m height perpendicular axes (azimuth and altitude) supported on hydrostatic bearings and driven by electrical direct drive motors with a precision of 0.3 arcsec under the maximum wind disturbance. 71 m width 52m diameter M1 Unit Segment Assembly 931 x M1 Segments 931 x Blanks + 19 x Spare Blanks 931 x Segments Polishing 4530 x M1 Edge Sensors 4530 x Sensors +813 x Electronics + Spares (100 sensors – 15 x controllers) 931 x M1 Segment Supports & SA Auxiliary Equipment [SA Handling Tools, SA Transport Containers, SA AIV Tools] Subcell 2394 x M1 Position Actuators 2394 x Actuators + 798 x Electronics + Spares (16 x PACT – 6 x Controllers) M1 Auxiliary Equipment Aux.
    [Show full text]
  • Book 0004.Pdf
    2 VLT Whitebook - List of Contents Introduction 9 Executive Summary 1. VLT Concepts and Performance 12 1.1 Scientific Objectives and Technical Requirements 12 1.2 Implementation and Future Optimization 13 1.3 Performance Requirements 14 1.4 The VLT Interferometer (VLTI) 16 1.5 Instrumentation 18 1.6 Science Operations 19 1.7 Data Archive and Distribution 20 2. Main Elements 21 2.1 Unit 8.2-m Telescope 22 2.2 The Main Mirrors (M1, M2 and M3) 24 2.3 Active and Adaptive Optics 26 2.3.1 Active Optics 26 2.3.2 Adaptive Optics 28 2.4 Array Configuration 29 2.5 Beam Combination and Interferometry 31 2.6 Instrumentation Package 32 2.6.1 VLT Instrumentation Projects 33 2.6.2 Observational Strategy 34 2.6.3 Observational Domains 35 2.6.4 Detectors 36 2.6.5 Spectroscopic Modes 36 2.6.6 Imagery 37 2.7 The Enclosures 38 2.7.1 Basic Functions 38 2.7.2 Design 39 3 2.7.3 Environmental Control 40 2.8 The Paranal Observatory 42 2.8.1 Infrastructure 42 2.8.2 Geographical Data 44 2.8.3 Observing Conditions 45 2.8.4 Seismics 49 2.9 The VLT End-to-End Model 51 2.9.1 Components 52 2.9.2 Model Architecture 53 3. The Optics 55 3.1 Concept 57 3.1.1. Optical Quality 59 3.1.2. Operating conditions 60 3.2 The Primary Mirror 61 3.2.1 Specifications 61 3.2.2 The Manufacturing Process 62 3.2.3 Mirror characteristics 63 3.3 The Secondary Mirror 67 3.3.1 Specifications 67 3.3.2 The Manufacturing Process 69 3.3.3 Mirror Characteristics 70 3.4 The Nasmyth Mirror 71 3.4.1 Specifications 71 3.4.2 M3 Hydraulic Support System 72 3.4.3 Manufacturing of the M3 Blanks 72 3.4.4 Mirror Characteristics 73 3.5 Sky Baffling and Pupil Alignment 74 3.6 The Cassegrain Focus 75 3.6.1 Optical Design 75 3.6.2 Cassegrain Adapter-Rotator 76 3.6.3 Instrument Interface 76 3.7 The Nasmyth Focus 77 3.7.1 Optical Design 77 3.7.2 Nasmyth Adapter-Rotator 78 4 3.7.3 Instrument Interface 81 3.8 The Coudé Focus 82 3.9 Coating 84 3.9.1 Concept 84 3.9.2 Implementation 84 3.10 Polarimetry 86 4.
    [Show full text]
  • Optical Alignment and Control Strategy
    8 OPTICAL ALIGNMENT AND CONTROL STRATEGY 8.1 Introduction The segmented mirror aspect of GMT presents challenges both for optical fabrication, discussed in later chapters, and for maintaining alignment and phasing of the optics in operation. There are currently two approaches to building extremely large telescopes (ELTs), both using segmented primary mirrors. The small-segment approach uses a large number of mirrors each approximately 1 m in diameter. GMT relies on seven 8.4 m segments. Large segments have tighter alignment tolerances, but only in the lateral directions (lateral translation and rotation). The lateral tolerances for large segments are still loose in comparison with the resolution of their positioning actuators, so the wavefront accuracy will be limited by the wavefront measurement, not by the alignment of the segments. Axial tolerances (piston and tilt) are roughly independent of segment size, and for any segment size the axial tolerances are much tighter than lateral tolerances. In terms of linear displacements as opposed to angular displacements, large segments are favored: 1 micron of tilt across an 8 m segment is better than 1 micron of tilt across each of sixty-four 1 m segments. The inclusion of a segmented secondary mirror in the optical design would at first seem to complicate the picture. In fact, it offers an opportunity to greatly simplify aligning and phasing of the telescope. The key feature is that the seven secondary mirror segments are conjugated one-to-one with the primary segments and can take care of the fine co-aligning and phasing of the subapertures. This greatly relaxes the position tolerances on the primary segments.
    [Show full text]
  • The Biggest Game in the Cosmos
    The New Planet Machine DISCOVER VOL. 27 NO. 02 | FEBRUARY 2006 | SPACE THE BIGGEST GAME IN THE COSMOS Astronomers ante up their bankrolls and reputations in a high-stakes bid to build the worlds largest telescope By Thomas Levenson Copyright ©2006 by Discover Media LLC. ILLUSTRATION BY TODD MASON/COURTESY OF CARNEGIE OBSERVATORIES. Article Used by Permission DREAM MACHINE: Plans call for the Giant MagEllan TElescope, which is scheduled for completion in 2016, to be housed in a 213-foot-tall rotating enclosure. Seven 27.6-foot mirror segments would be combined to create a giant light-gathering instrument with up to 10 times the resolving power of the Hubble Space TElescope. YOU WOULD NOT WANT TO PLAY POKER WITH WENDY Freedman. Even her children say so, she admits, and as she sits across the table on a summer morning in Tucson, Arizona, she gives no hint that she has just pushed almost all her chips into the middle of the table. At this moment, about six miles away, a giant orange oven rotates, spinning up to its target speed of five revolutions per minute, on its way to its programmed temperature of about 2130 degrees Fahrenheit. By then, it will hold a lake of glass, 20 tons of borosilicate. For another three days the oven will continue to spin, driving that lake of liquid glass into a parabola 330 inches across. Over the next several months, the glass will be slowly cooled and then polished exquisitely, to within .000001 of an inch of the theoretically perfect shape. Add an aluminum coating about 400 atoms thick, and there it will be: a telescope mirror, one of the largest in the world.
    [Show full text]
  • Very Large Telescope Paranal Science Operations VIRCAM/VISTA User Manual
    EUROPEAN SOUTHERN OBSERVATORY Organization Europeene´ pour des Recherches Astronomiques dans l’Hemisph´ ere` Austral Europaische¨ Organization f¨ur astronomische Forschung in der s¨udlichen Hemisphare¨ ESO - European Southern Observatory Karl-Schwarzschild Str. 2, D-85748 Garching bei M¨unchen Very Large Telescope Paranal Science Operations VIRCAM/VISTA User Manual Doc. No. VIS-MAN-ESO-06000-0002 Issue 85.0, Date 18/12/2009 V. D. Ivanov, T. Szeifert Prepared ................................................ Date Signature A. Kaufer Approved ................................................ Date Signature C. Dumas Released ................................................ Date Signature ii VIRCAM/VISTAUserManual VIS-MAN-ESO-06000-0002 This page was intentionally left blank VIRCAM/VISTAUserManual VIS-MAN-ESO-06000-0002 iii Change Record Issue Date Section affected Reason/Initiation/Documents/Remarks 0.10 09/09/2008 All Creation 1.00 18/12/2009 All First public release for P85. 1.01 01/07/2010 All Update for P86 Phase II and P87 Phase I. 1.02 01/12/2010 Twilight, overheads. Update P87 Phase II. 1.03 11/03/2011 Minor updates. Update P88 Phase I. 1.04 04/08/2011 Web links updated. 1.05 13/06/2013 Template tile6sky info. Update P92 Phase I. iv VIRCAM/VISTAUserManual VIS-MAN-ESO-06000-0002 This page was intentionally left blank VIRCAM/VISTAUserManual VIS-MAN-ESO-06000-0002 v Contents 1 Introduction 1 2 Applicabledocumentsandothersourcesofinformation 3 3 Abbreviations and Acronyms 5 4 VISTA and VIRCAM in a nut-shell 6 5 The VISTA Telescope – Technical Description 7 6 The VIRCAM - VISTA Infra-Red Camera 9 6.1 Generalfeatures ................................. ...... 9 6.2 Detectors ....................................... .... 11 6.3 Filters ......................................... .... 15 6.4 Sensitivity....................................
    [Show full text]