7800/8200 MORTISE LOCKS

© SARGENT Manufacturing Company 2004, 2005, 2007 1-800-727-5477 7800/8200 Mortise Locks www.sargentlock.com

Table of Contents

Specifications and Certifications ...... 1 Features ...... 2 Mortise SARGuide ...... 3 Coastal Series™ Decorative Levers, Roses, Escutcheons and Turns ...... 4 8200 Levers with Rose Designs ...... 5 8200 Escutcheon Designs ...... 6 8200 Freewheeling Design, ADA and Handicap Warning ...... 7 7800 Push/Pull Trim and 7800/8200 Anti-Vandal Trim ...... 8 7800 Knob and Escutcheon Designs ...... 9 Functions ...... 10-16 Strikes and Fronts ...... 17 Electrical Functions and Monitoring Options ...... 18 Turns, Emergency Releases and Indicators ...... 19 Cylinders and Rosettes ...... 20-21 Cylinder Requirements and Cams ...... 22 Prefixes and Options ...... 23 How to Order, Finishes, Packaging and Security Screw Chart ...... 24 ElectroLynx® As part of their promise to provide innovative, fast and effective, Suggested Architectural Specifications ...... 25 and higher security solutions to their customers, ASSA ABLOY Multi-functional Lockbody Options ...... Back cover Group companies offer ElectroLynx, a universal quick-connect system that simplifies the electrification of the door opening. ElectroLynx® is a registered trademark of ASSA ABLOY, Inc.

SARGuard Coating

• Revolutionary finish coating available on all SARGENT product lines, utilizes a silver-based antimicrobial compound from AgION Technologies AgION Antimicrobial is • As an integral part of the finish coating, SARGuard lasts for the life of the hardware EPA registered, FDA recognized and • SARGuard coating permanently suppresses the growth of bacteria, algae, fungus, mold and mildew. NSF certified It is effective against a broad spectrum of bacteria. The AgION antimicrobial is not intended • Non-toxic and completely safe. The AgION antimicrobial compound is EPA and NSF approved and FDA listed as a substitute for good hygiene.Coated for use in medical and food preparation equipment. products must still be cleaned to insure the surfaces will be free of destructive • Applications: Anywhere there is need for a clean environment (hospitals, laboratories, schools medical microbes. ASSA ABLOY makes no centers, daycare, food processing etc.) representations or warranties, express or implied, as to the efficacy of the AgION antimicrobial. A copy of the AgION SARGuide warranty is available upon request. • The SARGuide illuminated mortise lock increases visibility of exit locations in dark or smoke-filled passages, supplementing existing codes for egress lighting 7 0

0 • SARGuide utilizes state-of-the-art FLATLITE electroluminescent lighting from 2 ,

5 E-Lite Technologies Inc. 0 0

2 • Green-blue electroluminescent light provides 3 to 5 times the visibility of other lights , 4

0 • SARGuide can be wired for continuous operation or activation by fire alarm system 0 2 y • Mortise lock are placed low enough on a door to provide an extended window of n a

p opportunity for safe emergency egress m o • Supplements building exit signs required by code C g n

i • Intuitive operation. Integral “EXIT” signage guides users directly to the means of egress r u t

c • SARGuide can be ordered by adding the TL prefix to any 8200 series mortise lock a f with WT Trim, which allows free egress u n a M T N E G R

A On The Cover

S 8200 Mortise SARGuide © • 8237 Multi Function Lock LNJ LHRB 7 0 / 1 0 /

3 An ASSA ABLOY Group company 7800/8200 Mortise Locks 1-800-727-5477 Specifications www.sargentlock.com

Specifications

For Doors 1-3⁄4" (44mm) thick standard. For doors over 1-3⁄4" (44mm), specify door thickness and panels (if any) Backset 2-3⁄4" (70mm) only Case 12 gauge heavy duty wrought steel, zinc dichromate plated. Thickness 7/64" (3mm) (.109") Outside Front Plate Brass, bronze or stainless steel. 8" (203mm) x 1-1⁄4" (31mm), ANSI Standard A115.1. Adjustable at any angle from flat to beveled 1⁄8" (3mm) in 2" (51mm) Springs High carbon steel Hubs for Knobs Sintered iron copper infiltrated Hubs for Levers Cold forged steel Hubs for Institutional Stainless steel (3- prefix) Latchbolt Stainless steel 3⁄4" (19mm) projection one-piece, anti-friction reversible latch Auxiliary Deadlatch Stainless steel, non-handed Deadbolt One-piece hardened stainless steel, with 1" (25mm) projection Hand Specify hand on order; easily field reversible (if no hand is specified RH will be provided) Strike Brass, bronze or stainless steel; ANSI Standard A115.1; curved lip, non-handed (strike box optional) Keys Two, nickel silver (control key or emergency key must be ordered when required) Cylinder Brass, size #41 (1-1/8") standard (except for Freewheeling, size #46 (1-3/4")). Available with SARGENT Signature, V-10, XC and KESO Security Systems Masterkeying Can be masterkeyed or grand masterkeyed. Construction keying available. LA standard keyway. Finishes 3, 4, 9, 10, 10B, 10BL, 15, 20D, 26, 26D, 32, 32D Special finishes are available. (Contact factory for details) Classroom Security 38, 39, 40, 41 Functions (All mortise trim designs available except KE/LE 3 & 4 and PT trim or FE trim with 41 function) Stile 4-1/2" (114mm) minimum stile for 7800/8200, 4-3/4" (121mm) minimum stile for electrical function locks Door Prep ANSI A115.1 modified per template (see template for 7800/8200 lockbody & trim) Warranty 10 year limited warranty, 2 year limited warranty on electrified locks Warranty limited to replacement of Lockbody and/or components.

Certification Compliance

ANSI/BHMA Meets ANSI/BHMA A156.13 Series 1000 Operational Grade 1 and Security Grade 1 with all standard trims. ANSI/ASTM F476-84 Grade 40 with concealed mortise cylinder. Meets or exceeds ASTM F1577-95b paragraph 6.2 detention impact level 1 for deadbolt functions, level 3 for latchbolt only functions. Note: Removable Core and SFIC Cylinders do not meet Security Grade 1 requirements. ADA Meets A117.1 Accessibility Code. Meets BOMA International 4.13.8 Complies with American Disability Act; Consult local authorities UL UL and UL Listed to Canadian safety standards for A label (3 hour fire door) and lesser class doors, stamped letter F and UL symbol on armored front indicate listing Positive Pressure Meets positive pressure requirements UL 10C and UBC 7-2 (1997) California California State Reference Code (Formerly Title 19, California State Fire Marshal Standard) All levers with returns comply; levers return to within 1/2" (13mm) of door face Hurricane Codes Consult SARGENT website for certification and listings 7 0 0 2 , 5 0 0 2 , 4 0 0 2 y n a p m o C g n i r u t c a f u n a M T N E G R A S © 7 0 / 1 0 / An ASSA ABLOY Group company 1 3 7800/8200 Mortise Locks 1-800-727-5477 Features www.sargentlock.com

SARGENT Mortise Locks (Patent Pending) are designed and constructed with high quality components to provide maximum security, performance and durability. These locks represent over a century of innovation and experience in manufacturing hardware and are the industry’s benchmark for mortise locks: Strong - Durable - Flexible – Innovative and Secure Green Catch Screw for Multi-function Locks only Outside front plate 1/16" (1.6mm) brass, bronze or stainless steel. Cylinder retainer-two prong Adjustable for door bevels from grip meets Security Grade 1 flat to 1/8" (3mm) in 2" (51mm) Extra strong 7/64" (3mm) steel case for improved impact resistance

6-pin solid brass cylinder standard; 3/4" (19mm) projection stainless multiple keying systems available steel one-piece latchbolt, reversible without opening case. Anti-friction Heavy gauge corrosion resistant piece is securely staked in place for parts provide security, reliability, quiet operation and prevents durability and longevity scratching of strike plate All trim designs through-bolted. Spring load spindles automatically Non-handed stainless adjust for door thickness steel auxiliary deadlatch

Inside front full 1/8" (3mm) cold rolled steel holds lock securely in door Heavy duty hubs and spring Solid brass, bronze or stainless cartridge for superior strength steel levers. ADA compliant. 8237 LNJ Shown and cycle life Full latch retraction at 30° for Features ease of operation. Maximum Strength & Durability • Available with vandalism deterrent trim and/or secure fastener • Exceeds ANSI A156.13, Series 1000, Operational Grade 1 and options for high abuse conditions Security Grade 1 with all standard trims • UL Listed (10C and UBC 7-2, 1997) for use on fire doors up to • Meets and exceeds ASTM F1577-95b paragraph 6.2 detention 4’x10’ and double door applications impact level 1 for deadbolt functions, level 3 for latchbolt • Available with push/pull trim. Perfect for hospital applications only functions • SARGENT uses engineered solutions and flexible manufacturing • 12 gauge (.109) steel case and cap processes to accommodate special applications • 1/8” (.125) cold-rolled steel inside front holds lock securely in door Innovation • Heavy duty wrought steel hubs and high carbon steel spring • First in the industry to offer a multi-functional lockbody that cartridge provide superior strength and cycle life embodies 9 functions in 1 lockbody! • 3/4” stainless steel latchbolt. One piece construction to offer • 18 new functions, for a total of 58 to meet virtually 1” total bearing surface against the strike every specification • Stainless steel hubs available • Easy operation. Only 30º of lever rotation required to • One-piece hardened stainless steel deadbolt with retract latchbolt 1” (25mm) projection • Lever springs contained inside of the lock case for easier • Exceeds 8 times the ANSI/BHMA A156.13 Grade 1 standard for installation cycle testing! 7

0 • Unique spring design. Provides longer lock life, no lever sag

0 • 10 Year mechanical warranty. No service required to 2 and simple installation ,

5 maintain warranty 0

0 • SARGENT’s revolutionary SARGuard™ available. This antimicrobial 2

, Maximum Flexibility silver-based finish coating permanently suppresses the growth of 4 0

0 • Fast and easy installation. Lock is easily re-handed without bacteria, algae, fungus, mold and mildew. EPA and NSF approved 2 y removing parts or opening the lock case and FDA listed n a p • Aesthetic design. Many escutcheon and lever styles available to • Broad offering of electro-mechanical configurations offer higher m o match a wide range of styles security for the most demanding access/egress control applications C g featuring ElectroLynx quick connectors n • 12 Standard architectural grade finishes, including new US15 i r u Satin Nickel t

c Security a ® f • Multi-functional lockbody makes it easy to change functions in • Torx and spanner screws u n a the field! • Classroom and hospital security functions available M

T • 58 functions including 4 electrical functions and 4 Profile/keypad

N • Multiple security trim options available: Free-wheeling, security

E functions. The most in the industry for a broad range of

G escutcheon and anti-vandal pull trim (patent pending) R applications! A

S • Security key systems available (V-10, Signature, Keso, Keso F1,

© • Versatile. Offered for door thicknesses ranging from & XC) 1-3/8” (35mm) to 6” (152mm) 7 0 / 1 0 / 3 2 An ASSA ABLOY Group company 8200 Mortise Locks 1-800-727-5477 ™ SARGuide www.sargentlock.com

SARGuide™ System SARGuide,™ with integrated electroluminescent “EXIT” signage, addresses the increasing concern about safe public egress, particularly in low-visibility conditions. Research shows that in panic conditions, exit signs and locations go unnoticed. Smoke rises and can quickly block the visibility of standard exit signage. SARGuide increases visibility which provides an extended window of opportunity for safe emergency egress. SARGuide can be wired for continuous operation or for operation only when an emergency alarm is activated. Currently required egress equipment (exit signs and emergency lights) may offer limited guidance when building occupants are unfamiliar with secondary exit locations. SARGuide dramatically improves the safety of any public building.

SARGuide can be used as a stand alone feature or as an integral part of E-Lume-A-Path™ Egress Path Marketing Systems. E-Lume-A-Path enhances the ability of a person to escape a building by illuminating the path to safety through existing exits. The system will respond to a power outage or fire alarm and consists of a strip of FLATLITE® ™ electro-luminescent lamp at the floor level that can SARGuide go down hallways, around corners and stairwells, 8200 Mortise Lock hundreds of feet in length. It can help supplement currently required Egress equipment such as Exit (TL- Prefix) Signs and Emergency Lights, which may have limited effectiveness when building occupants do not know the location of secondary exits.

Features and Benefits Mortise Features SARGuide™ Benefits • Non-handed • Highly visible in smoke and other low visibility conditions • Lamp can be used on internal trim (for external trim, • Three to five times greater visibility than any other consult factory) light source • Includes all features of the NEW 8200 Mortise Lock • Can be spotted easily from considerable distances • Available with WT escutcheon design only and all standard lever • No filaments to break or fail designs. Must specify TL- prefix when ordering. • Immune to vibration or shock SARGuide™ Features • Extremely durable construction. Continues to operate even 7

® 0

• Illuminated utilizing the patented FLATLITE electroluminescent if pierced. 0 2 ,

lamp embedded within the mortise lock escutcheon • Intuitive operation. Integral “EXIT” signage guides users directly 5 0 0

• Supplements building exit signs required by code to the means of egress. 2 , 4

• SARGuide can be wired for continuous operation (always on), • Pre-wired with ElectroLynx™ plug-in universal connectors 0 0 2

or wired into fire alarm system for operation only when alarm ™ y

SARGuide Applications (For interior use) n is activated a p

• Stairwells m

• Dual voltage: 24 VAC or VDC input from SARGENT (or other) o • Corridors C power supply with battery back-up g n i • Auditoriums r

• Simple installation u t c

• Schools a • For retrofit applications consult factory f u

• Universities n • Other verbiage available with the lamp product upon request a M

(special order) • Theaters T N • Lamp replacement kit available • Hospitals E G R A S

Note: Requires the industry standard depth for mortise locks of 4 1/2". © 7 0 / 1 0 / An ASSA ABLOY Group company 3 3 8200 Mortise Locks Coastal Series™ 1-800-727-5477 Decorative Levers, Roses, Escutcheons & Turns www.sargentlock.com

Features S - Sanibel™ 5" • Elegant trim styles that meet your architectural design needs with the highest quality (127mm) mortise lock construction ) " 6 m 1 / • Levers with curves and contours provide a comfortable grip 2-1/2" m 7 7 - 8 3 (63mm) ( • All levers meet ADA guidelines • Coronado lever meets California’s State Fire Marshall Standard • Shown with contemporary rose CR • Coastal Series only are available with 8200 Standard design rose/escutcheon trim • Must specify hand when ordering designs only, as a special order (Consult Factory). • All levers – solid cast brass C - Coronado™ • Escutcheons – solid forged brass 5-1/4" (133mm) • Roses – machined from solid brass )

m +/- 7/16"

• Finishes available – 3, 4, 9, 10, 10B, 10BL, 15, 20D, 26, 26D " m 2

3 (11mm) 6 Note: 184 emergency release available in Traditional and Contemporary designs. ( • Shown with traditional rose TR

Roses, Escutcheons & Turns R - Rockport™ 4-3/4" (121mm) 2" 5/16" 2" 5/16"

TE Traditional CE Contemporary ) "

(51mm) (8mm) (51mm) (8mm) m 4 / m

3 +/- 1-7/8" - Escutcheon Escutcheon 0 2 7

( (47mm)

• Shown with traditional rose TR ) ) " " m m 8 8 / / m m 7 7 0 0 - - 0 0 Y - Yarmouth™ 7 7 2 2 ( ( 5" (127mm) ) " m 8 / m 5 - 7 +/- 1-7/8" 2 6 ( (47mm)

TR Traditional Rose CR Contemporary Rose • Shown with contemporary rose CR • Must specify hand when ordering

G - Gulfport™ 5" (127mm) 2-3/16" 5/16" 2-3/16" 5/16"

(56mm) (8mm) (56mm) (8mm) ) " 6 m 1 / m 5 +/- 1-15/16" 4 1 - 7 (

2 (50mm) 130T Traditional Turn 130C Contemporary Turn • Shown with contemporary rose CR ) ) " " • Must specify hand when ordering m m 4 8 / / m m 1 1 - - 7 4 2 2 5 5 ( ( NOTE: All lever height (+/- 1/16")

7 measurements represent total distance 0

0 from door face. 2

, 13/16" 13/16" 5

0 (20mm) (20mm) 0 2 , 4 0 0 2 y n a p m o C

g How To Order n i r u t c a f Rose x Lever (TR X C) u n a Example: 8237TRC 26D RH M T N E G R A S © 7 0 / 1 0 / 3 4 An ASSA ABLOY Group company 8200 Mortise Locks 1-800-727-5477 Levers with Rose Designs www.sargentlock.com

• All lever meet ADA guidelines. • Lever designs C, J, L and P have lever returns within 1/2" (13mm) or less of door face and meet California State Reference Fire Code • All lever designs on this page are available with only with Standard rose and escutcheon designs, which does NOT include Coastal or Studio/Metro designs.

A Lever Design P Lever Design • Lever: A-Solid forged • Lever: P-Solid forged or cast 5" or cast 5-1/2" (127mm) (140mm) • Must specify hand ) ) " " 6 m when ordering m 2 1 / / m m 1 5 +/- 5/16" - 7 1 +/-

1 1-15/16" 2 6 - 5 ( ( (8mm) 2 (49mm)

B Lever Design W Lever Design 5" • Lever: B-Solid (127mm) • Lever: W-Solid bar stock 4-1/2" (114mm) forged or cast ) " ) m 8 " / m m 2

5 +/- 1-5/8" / - 7

m +/- 2-1/16" 1 2 6 - 4

( (41mm) 2 6 (52mm) (

E Lever Design L Rose Design

• Lever: E-Solid 4-1/2" • Rose: L-Heavy wrought forged or cast (114mm) ) " m 2

/ +/- 2" 5/16" m 1 - 4 (51mm) (8mm) 2 6

( 3-1/2" (89mm)

F Lever Design O Rose Design 4-1/2" • Lever: F-Solid (114mm) • Rose: O-Heavy wrought forged or cast ) " m 4 / +/- 5/16" m 1-15/16" 3 - 7

2 (8mm) 6 (49mm) ( 2-3/4" (67mm)

J Lever Design LN Rose Design 5-1/4" • Lever: J-Solid bar (133mm) • Rose: LN-Heavy wrought stock ) " 6 m

1 +/- 5/16" / m 3 5/16" 1 (8mm) 1 - 7 (

2 (8mm) 7

2" 0 0

(51mm) 2 , 5 0 0 2 ,

L Lever Design E Rose Design 4 0 0

5" 2

• Lever: L-Solid (127mm) • Rose: E-Heavy wrought y n a

forged or cast p m o ) 5/16" C "

m +/- 5/16" 8 / (8mm) g m 3 (8mm) n - i 0

3-1/16" r 2 6 ( u

(78mm) t c a f u n a M T N E G

NOTE: All lever height (+/- 1/16") measurements R A

represent total distance from door face. S © 7 0 / 1 0 / An ASSA ABLOY Group company 5 3 8200 Mortise Locks 1-800-727-5477 Escutcheon Designs www.sargentlock.com

• Cylinders will protrude from each escutcheon face on double cylinder functions only

2-1⁄2" LE1/LE2 Escutcheon Design WT Escutcheon Design (65mm) • Escutcheon: • Escutcheon: WT-

LE-Cast CL of Heavy wrought cylinder ) )

• LE1- (2) Exposed " • Surface mounted ) m " m 8 ⁄ 8 ⁄ m m "

m C of 7 L screws inside 7 both inside and 5 - 8 8 ⁄ - ) ) m 7 3 cylinder 9 5 6 " 4 ( - 1 m m " 6 9 ( C of outside 7

L 8 ⁄ 1 1 m • LE2- (2) m ) ⁄ (

lever 3 0 7 9 " - m - 7 8 8 7 ⁄

Concealed • (4) Exposed 6 1 1 m (

( C of 7 L - 8 3

screws inside screws both 9 lever inside and ( 1-3⁄4" (44mm) outside

(Shown with L Lever) (Shown with L Lever)

TL-WT Escutcheon Design (TL- Prefix designates SARGuide) LE3/LE4 Escutcheon Design 2-1⁄2" • Concealed Cylinder • Escutcheon: (65mm) designed Escutcheon, CL of TL-WT- cylinder ) Exposed Barrel Only ) Heavy wrought " m " m 8 8 ⁄ ⁄ ) m m 7 7 C of 5 • Surface mounted - - L 8 m "

• Escutcheon: 7 3 6 9 ) 8 cylinder ⁄ ) 1 ( m (

5 both inside and m " ) 4

C of " - LE-Cast L m 8 9 8 " ⁄ ⁄ 7 m lever m 1 m 6 7 3

outside 7 ( - - 8 1 m ⁄ 8 3 7 9 0

• LE3- (2) Exposed 9 1 ( - ( 7 CL of 6 • (4) Exposed 1

screws inside ( lever screws both • LE4- (2) Concealed 1-3⁄4" inside and screws inside (44mm) outside • Not available on double (Shown with L Lever) (Shown with L Lever) • SARGuide cylinder functions opening • Only available with 78-41 2" x 3/4" cylinder - limited keyway and Note: SARGuide is only available with key system offerings - see TL- WT Escutcheon. cylinders section.

LW1 Escutcheon Design LS Escutcheon Design • Escutcheon: 3/8" • Escutcheon: (10mm) LW1-Wrought CL of cylinder LS-Forged CL of ) • (2) Exposed ) cylinder " m " m )

8 • Security Trim. ) ⁄ 8 ⁄ ) " " screws inside m m ) m 7 7 m 8 6 5 - 8 - m / Cylinder is " m 1 7 m 3 ⁄ 9 6 7 4 m ⁄ ( m - 1 8 1 " 0 m ( 3 7 3 C of 9 1 - 8 7 3 L protected by ( - 9 7 1 0

lever C of 6 1 L ( 2 ( ( the Escutcheon lever • (4) Spanner

7 security screws

0 2" 0 are exposed on 2 (51mm) 2-1⁄2" ,

5 inside trim (64mm) 0 0

2 (Shown with L Lever) standard , 4 0 0 2 y n a p m o C g n i r u t c a f u n a M T N E Inside G

R LSL Design A S © 7 0 / 1 0 / 3 6 An ASSA ABLOY Group company 8200 Mortise Locks Freewheeling Trim Design – FE 1-800-727-5477 ADA and Handicap Warning www.sargentlock.com

Outside Inside

CL of

Inside Outside ) cylinder " ) m ) " 6 ) " 6 1 m m m / " m 8 1 5 / / 1 m 8 m - / 0 m 7 1 9 - 9 8 5 2 4 1 6 - ( 3 9 - 9 ( 1 7 6 ( 1 CL of ( lever

8225 FEL shown

13/16" ) m " "

(21mm) ) 8 6 / m m 1 5 1 / - 4 3 m 1 ( 1 6 - 4 ( 1 2-3/8" (60mm) Freewheeling Lever - vandal resistant Maximum projection varies by lever design. Largest projection is “A” lever – 3-9/16" (90mm)

Features The Freewheeling Mortise Trim is designed • Meets or exceeds ANSI A156.13 Series • Levers A, B, E, F, J, L, P, W available for areas that are susceptible to vandalism 1000 Operational Grade 1 and Security • Lever designs J, L and P have lever returns including schools, universities, public buildings, Grade 1. Removable and SFIC cylinders within 1/2" (13mm) back doors of businesses and any exterior do not meet Security Grade 1. doors where excessive or abusive force • Cylinder will protrude from escutcheon • Forged brass outside escutcheon face on double cylinder functions only might be applied to the lever handle trim. trim provides added protection This design allows the outside lever handle against vandalism • Cylinder sizes #46 (1-3/4") outside, to swing freely, down to 70°, in the “locked” #41 (1-1/8") inside standard on • Stainless steel lever bushing protects 1-3/4" (44mm) doors mode. This eliminates resetting the trim against wear after vandalism attempts because the lever • Specify hand. Easily field rehanded automatically returns to its original position. • Stainless steel lugs and through-bolted trim design for proper alignment and • Patented design – U.S. Patent No. 5,992,195 • For 1-3/4" (44mm) doors standard. For 2" increased security (51mm) and 2-1/4" (57mm) thick doors, • Prefixes available: 3-, 10-, 10-UL-, 11-, 21-, must specify door thickness on order. • Functions available – 04, 05, 16, 17, 23-, 36-, 37- 60- 63-, 64-, 74-, 75-, 76-, 77-, 24, 25, 26, 31, 35, 36, 37, 38, 39, 40, 82-, SG-, VA-, VC- and VS- • Vandal resistant trim 51, 65, 66 Some prefixes not available on thicker doors. Consult factory ADA and Handicap Warning Lever Return to Door Tactile Handicapped Warning • Lever designs J, L and P • Milled Lever • Lever returns within 1/2" (13mm) • 1/16" (2mm) wide milled grooves of door face or less • A Lever – 4 grooves on • Meets ADA Compliance for bottom surface of lever national codes • B, E, J, L, P and W Levers – 4 grooves on backside surface of lever Standard Thumb Turn • F Lever – 4 grooves on top • Meets ADA Compliance for

and bottom surface of lever 7 0

national codes 0 • B Lever shown 2 ,

1-3⁄8" (35mm) 5

• Order as: 0

Turn 0 130KB, 130W or 130KA x finish 2 ,

Tactile Handicapped Warning 4 0

See page 19 for design 0 • Knurled knob 2 y n a

• Knobs are NOT ADA compliant p m

LB – Thumb Turn o C

• Meets the tougher local ADA g n i r

requirements u t c a • 40% larger than standard f u n

2" (51mm) thumb turn Keys • Large key bows are available a Turn M • Order as: 130LB x finish • Standard key bows can have T N attachments added to increase E G R

the grip area A S

• Keys are NOT ADA compliant © 7 0 / 1 0 / An ASSA ABLOY Group company 7 3 7800/8200 Mortise Locks 7800 Push/Pull Trim – PT 1-800-727-5477 7800/8200 Anti-Vandal Trim – AV www.sargentlock.com

7800 Push/Pull Trim – PT 4-5/8" The Push/Pull design known for its ease of operation is coupled with the (117mm) strength and integrity of a mortise lock to provide greater versatility. The trim, ) commonly used in hospitals and health care facilities, can now service conference ) " " m m 4 2 / / m m 3 rooms, handicapped restrooms, laboratories and pharmacies that require more 1 - - 0 8 2 1 7 3 ( durability and security features than a cylindrical lock can provide. ( ) " m 4 ) / m " 3 m - 0 8 / 2 7 m ( 7 - 8 1 4 (

4-1/2" (114mm) Push down Push up Push up Push down 7837 PT • Spindle centered in escutcheon Pull up Pull up Pull down Pull down Horizontal Mount Shown Features

• Paddle trim orientation can be mounted as a standard product in • 6 Lobe security type screws (Torx®) standard for PT trim only – vertical (up or down) and horizontal positions Spanner Security screws optional as 37-prefix • Down or horizontal paddle orientation is required for cylinder • Engraving on paddle – consult factory applications • Functions available: 04, 15, 16, 17, 24, 26, 37, 43, 45, 50, 65 • Horizontal paddle orientation is required for functions having – All other functions available as specials, except trim thumb turns one-side only • Stile requirement – minimum of 5" (125mm) • Lead lining is available as option (Lockbody only) • Door thickness 1-3/4" (44mm) to 2" (51mm) standard with • Covers are heavy wrought stainless steel, brass or bronze adaptable spindle (For thicker doors, consult factory) • Paddles are cast stainless steel brass or bronze • Easy installation • U.S. Patent No. 6,398,274 • Handing is easily field reversible • Finishes: 3, 4, 9, 10, 10B, 10BL, 20D, 32, 32D • Through-bolted trim for stability 7800/8200 Anti-Vandal Trim – AV Designed for exterior doors that require extra security or resistance to vandalism. AV anti-vandal trim plates have an 1-5/16" extended lip on the active side of the door to provide (33mm) extra protection for the latchbolt, deadbolt and deadlatch. A matte plastic coated grip edge provides a comfortable 10-9/16" pull that feels good over wide temperature ranges. Fully (268mm) through-bolted without exposed exterior fasteners for a clean look and increased security.

Features • Heavy duty 12 gauge stainless steel in 32D finish only 667-1 Shown 8-3/16" • Through-bolted through mortise lock body and door (208mm)

7 for added strength 667 AV Kit 0 0 2

, • Handed – Specify RHRB or LHRB Retrofit kits for 7800, 8200 & 9200 mortise locks 5 0

0 • ADA Compliant 2 667 Kit includes: , 4

0 • Patent Pending • AV Pull • 1SB Rosette 0

2 • (4) 1/4-20 screws • Instructions & Templates y • Available for all inside trims except LS/KS, FE and PT n

a • (4) Cup washers p • Functions available: See Chart to the Right m o RHRB LHRB Functions C • For inactive door, available without protective lip g 667-1 667-2 04, 06, 17, 28, 29, 30, 31,50, 51, 52, 91 & 92 n i r

u 82-4034 82-4035 AV Trim has an extended lip t c a Inside trim is through-bolted to AV trim f u

n 667-3* 667-4* 03, 20, 21, 22, & 23 a

M 82-4036 82-4037 AV trim has an extended lip & cylinder T

N hole for deadbolt functions only E

G 667-5* 667-6* Designed as a Pull does not have an R

A 82-4044 82-4045 extended lip or cylinder hole S © * No Through-Bolt Post 7 0 / 1 0 / 3 8 An ASSA ABLOY Group company 7800 Mortise Locks 1-800-727-5477 Knob and Escutcheon Designs www.sargentlock.com

• All knob designs are available with standard rose designs (Does not include Coastal Series).

C Knob Design K Knob Design D Knob (Detention) with SL Rose • Knob: C-Wrought 2-5/8" • Knob: K-Cast 1-13/16" • Designed for (67mm) (46mm) detention and (prior designation 1485) psychiatric facilities • Only available ) ) with SL Rose " " m m 4 4 / / m m 1 1 - - 7 7 2 2 5 5 ( (

B Knob Design N Knob Design 3" 2" • Knob: B-Wrought (76mm) • Knob: N-Wrought (51mm) (prior designation 1673) ) ) " " m m 4 8 / / m m 1 1 - - 7 4 2 2 5 5 ( (

2-1/2" KW1 Escutcheon Design (64mm) 2" KS Escutcheon Design (51mm) 3/8" • Escutcheon: (10mm) KW1-Wrought • Security Trim, Cylinder is protected by the Escutcheon • (2) Exposed CL of screws inside cylinder • Escutcheon: KS-Forged CL of cylinder ) ) • (4) Spanner screws are m " m ) 8 ) " m / " m " 8 m 3 7 exposed on inside trim m - 8 8 4 0 / / m 3 9 m 2 7 ( 3 7 ( - 8 - 9 3 9 7 ( • Consult factory for 70, 71, 1 ( CL of 72 and 73 function C knob L of availability as a special knob • All functions will have escutcheons both sides (Shown with B Knob) Outside WT Escutcheon Design KE3/KE4 Escutcheon Design 1-3/4" 2-1/2" (44mm) • Escutcheon: WT- (65mm) • Concealed Cylinder designed Heavy wrought Escutcheon, Exposed Barrel Only • Surface mounted CL of CL of cylinder • Escutcheon: KE3-Cast cylinder • (4) Exposed ) ) ) ) " " m m " m " 8

8 • KE3- (2) Exposed

screws inside m / / 8 m 8 / m m / 7 3 7 m 5 - 8 - 4 7 - 8 - 8 3 9 7

screws inside 9 7

and outside 1 ( 3 9 1 ( ( ( CL of • KE4- (2) Concealed C 7

knob L of 0

screws inside 0

knob 2 ,

• Not available on double 5 0 0

cylinder functions 2 (Shown with B Knob) , 4

(Shown with B Knob) 0 • Only available with 78-41 0 KE1/KE2 Escutcheon Design 1-3/4" 2 cylinder - limited keyway y

(44mm) n a

and key system offerings – p m

• Escutcheon: KE1-Cast see cylinders section. o C C L of g n • KE1- (2) Exposed cylinder i r u

screws inside t c ) a ) f " " m m 8 u 8 • KE2- (2) Concealed / / m m n 7 5 4 - 8 - a 9 3 9 7

screws inside ( 1 M ( T

CL of N E

knob G R A S ©

(Shown with B Knob) 7 0 / 1 0 / An ASSA ABLOY Group company 9 3 7800/8200 Mortise Locks 1-800-727-5477 Functions www.sargentlock.com

Single Cylinder without Deadbolt

*‡04 Storeroom or Closet *!36 Closet 8204, 7804 • Key outside or lever/knob inside 8236, 7836 • Key outside locks and unlocks outside retracts latchbolt lever/knob • Lever/Knob outside rigid at all times • Lever/Knob outside retracts latchbolt, • Lever/Knob inside retracts latchbolt except when locked • Auxiliary deadlatch • Inside: no lever/knob or cylinder • A Multi-Function Lock Body • A Multi-Function Lock Body • ANSI F07 • Auxiliary deadlatch

*05 Office or Entry *‡37 Classroom 8205, 7805 • Key outside retracts latchbolt when outside 8237, 7837 • Key outside locks and unlocks lever/knob is locked lever/knob outside • Lever/Knob inside retracts latchbolt only, • Key outside retracts latchbolt outside Lever/Knob remains locked • Lever/Knob outside retracts latchbolt, • Lever/Knob outside is locked/unlocked by except when outside lever/knob is locked thumb turn inside or by key outside by key • Auxiliary deadlatch • Lever/Knob inside always retracts latchbolt • A Multi-Function Lock Body • Auxiliary deadlatch • ANSI F04 • A Multi-Function Lock Body The Multi-Function Advantages with Rose Trim: • ANSI F05 (1) This lock will accommodate 04,05,15 & 37 Functions without additional parts. 55 Office or Entry (2) By adding an additional Cylinder, this lock will accommodate 8255, 7855 • Key outside retracts latchbolt when 17 & 38 Functions. outside lever/knob is locked • Lever/Knob inside retracts latchbolt only, (3) By adding a Trim One Side Kit, this lock will accommodate outside Lever/Knob remains locked 06, 13, 31 & 36 Functions. • Lever/Knob outside is locked by Note: Office/Entry Function with toggle is available– order as a toggle only 55 function. • Auxiliary deadlatch

06 Storeroom or Service 56 Office & Inner Entry Lock 8206, 7806 • No outside lever/knob, cylinder only 8256, 7856 • Key outside retracts latchbolt when outside • Lever/Knob inside or key outside lever/knob is locked retracts latchbolt • Lever/Knob inside retracts latchbolt and unlocks outside lever/knob • Auxiliary deadlatch • Lever/Knob outside is locked by thumb turn • Same as 04 Function without or key lever/knob outside • Auxiliary deadlatch • A Multi-Function Lock Body 7 0 0

2 !

, *31 Utility 67 Institutional Privacy 5 0

0 8231, 7831 • Key outside retracts latchbolt 8267, 7867 • Key outside retracts latchbolt, with 2 ,

4 • Lever/Knob outside is always rigid override of turn inside when held in 0

0 locked position 2 • Inside: no lever/knob or cylinder y n • Lever/Knob outside retracts latchbolt a • A Multi-Function Lock Body p except when locked by thumb turn m o • Auxiliary deadlatch C • Lever/Knob outside unlocks when the door g n i closes or operating lever/knob inside r u t c • Lever/Knob inside always retracts latchbolt a f u • Auxiliary deadlatch n a

M • ANSI F26 T *8200 Available with Freewheeling Trim N E

G ‡7800 Available with Push/Pull Trim R

A !

S CAUTION: Not recommended for use on any door used for Life Safety egress © If shaded, knob or lever rigid at all times 7 0 / 1 0 / 3 10 An ASSA ABLOY Group company 7800/8200 Mortise Locks 1-800-727-5477 Functions www.sargentlock.com

89 Holdback 91 All Purpose Holdback 8289 • Key outside retracts latchbolt when 8291 • Key outside retracts latchbolt lever/knob outside is locked • Key outside can lock latchbolt in • Lever/Knob outside retracts latchbolt, retracted position unless locked by key outside • Lever/Knob inside retracts latchbolt • Lever/Knob inside is always active • There is no outside lever or knob • Auxiliary deadlatch • Auxiliary deadlatch • Latch hold back - set by rotating lever all • Latch hold back - set by rotating lever all the way down, then rotate key twice the way down, then rotate key twice toward latchbolt. Lever will remain in toward latchbolt. Lever will remain in rotated position for unlocked indication. rotated position for unlocked indication

Single Cylinder with Deadbolt

!*‡24 Storeroom Door 30 Dummy Trim Deadlock 8224, 7824 • Key outside or thumb turn inside retracts 8230, 7830 • Deadbolt operation only and projects deadbolt • Key outside retracts and projects deadbolt • Lever/Knob either side retracts latchbolt • Lever/Knob inside retracts deadbolt • Latchbolt and deadbolt are independent of • Lever/Knob outside is always rigid each other • Same as 28 Function without a thumb turn • ANSI F21

*25 Dormitory or Exit !*35 Storeroom 8225, 7825 • Key outside or thumb turn inside retracts 8235, 7835 • Key outside retracts and projects deadbolt and projects deadbolt • Lever/Knob outside retracts latchbolt, • Lever/Knob from either side retracts except when deadbolt is projected latchbolt, when the deadbolt is in the • Inside: no lever/knob or cylinder retracted position • Lever/Knob outside is locked, when the deadbolt is projected • When deadbolt is projected, lever/knob inside retracts latchbolt and deadbolt simultaneously, unlocking outside ‡43 Apartment Corridor Door lever/knob 8243, 7843 • Key outside or thumb turn inside retracts • ANSI F13 and projects deadbolt • Key outside retracts both latchbolt and !27 Closet or Storeroom deadbolt, lever/knob outside 8227, 7827 • Key outside retracts and projects deadbolt remains locked • Lever/Knob from either side • Lever/Knob from either side retracts retracts latchbolt latchbolt, except when lever/knob outside • Same as 24 function without thumb turn is locked • Latchbolt and deadbolt are independent of • Lever/Knob outside is locked by toggle each other or projecting deadbolt • Lever/Knob outside is unlocked by 7

toggle only 0 0 2

• Lever/Knob inside (when deadbolt is , 5 0

projected) retracts latchbolt and deadbolt 0

28 Dummy Trim Deadlock 2 simultaneously, and lever/knob outside , 4

8228, 7828 • Deadbolt operation only 0 remains locked 0 2

• Key outside retracts and projects deadbolt y • Auxiliary deadlatch n a

• Lever/Knob inside retracts deadbolt p

• ANSI F20 m o

• Lever/Knob outside is always rigid C g n • Thumb turn inside retracts and i r u t

projects deadbolt c a f u n a M

*8200 Available with Freewheeling Trim T N

‡7800 Available with Push/Pull Trim E G

! R

CAUTION: Not recommended for use on any door used for Life Safety egress A S

If shaded, knob or lever rigid at all times © 7 0 / 1 0 / An ASSA ABLOY Group company 11 3 7800/8200 Mortise Locks 1-800-727-5477 Functions www.sargentlock.com

‡45 Dormitory or Exit *‡ 50 Hotel Guest 8245, 7845 • Key outside or thumb turn inside retracts 8250, 7850 • Hotel Cylinder Required (50 Function and projects deadbolt Cylinder) with two types of Keys (Standard • Key outside retracts both latchbolt and & Emergency) deadbolt, lever/knob outside • Standard Key outside retracts latchbolt remains locked only, will not retract or project deadbolt • Lever/Knob outside is locked by toggle or • Emergency Key outside will retract projecting deadbolt latchbolt and deadbolt and also project • Lever/Knob inside (when deadbolt is deadbolt projected) retracts latchbolt and deadbolt • Thumb turn inside retracts and projects simultaneously, and lever/knob outside deadbolt remains locked • Lever/Knob inside retracts both latchbolt • ANSI F12 and deadbolt simultaneously • Lever/Knob outside is always rigid • Auxiliary deadlatch • Not available with certain key systems (see Prefix chart in this catalog for restrictions) !47 Front Door or Apartment Corridor Door • ANSI F15 8247, 7847 • Key outside or thumb turn retracts and projects deadbolt *51 Storeroom Deadbolt • Key outside operates both latchbolt and 8251, 7851 • Key outside will retract latchbolt and deadbolt deadbolt and also project deadbolt • Lever/Knob outside is locked by toggle or • Lever/Knob inside retracts both latchbolt projecting deadbolt and deadbolt simultaneously • Lever/Knob outside is unlocked by • Lever/Knob outside is always rigid toggle only • Thumb turn inside retracts and projects • Lever/Knob inside (when deadbolt is deadbolt projected) retracts latchbolt only, deadbolt remains projected and outside lever/knob • Auxiliary deadlatch remains locked • Same as 50 function with a standard • ANSI F08/F10 cylinder

Double Cylinder without Deadbolt

*‡16 Apartment, Exit or Public Restroom *38 Classroom Security Intruder Latchbolt 8238, 7838 • Key from either side locks and unlocks 8216, 7816 • Key outside retracts latchbolt, when outside lever/knob outside lever/knob is locked • Key from either side retracts latchbolt • Key inside is required to lock and unlock lever/knob outside • Lever/Knob outside retracts latchbolt, except when outside lever/knob is locked • Lever/Knob inside always operable by key • Auxiliary deadlatch • Lever/Knob inside always retracts latchbolt • Special cam required for inside cylinder • Auxiliary deadlatch • ANSI F09 • ANSI F32 7 0 0

2 ! ,

5 *‡17 Asylum or Institutional 0 0

2 8217, 7817 • Key from either side retracts latchbolt , 4 0

0 • Lever/Knob on both sides rigid at all times ! 2 59 Double Locking y • Auxiliary deadlatch n a p • ANSI F30 8259 • Key from either side locks and unlocks m

o inside & outside levers/knobs C g • Key from either side retracts latchbolt n i r u • Key from either side can retract latchbolt t c a

f without unlocking levers/knobs u n

a • Auxiliary deadlatch

M *8200 Available with Freewheeling Trim T

N ‡7800 Available with Push/Pull Trim E

G !

R CAUTION: Not recommended for use on any door used for Life Safety egress A S

© If shaded, knob or lever rigid at all times 7 0 / 1 0 / 3 12 An ASSA ABLOY Group company 7800/8200 Mortise Locks 1-800-727-5477 Functions www.sargentlock.com

90 Classroom Security Holdback 92 All Purpose Holdback 8290 • Key either side retracts latchbolt when 8292, 7892 • Key outside retracts latchbolt lever/knob outside is locked • Key inside can lock latchbolt in • Lever/Knob outside retracts latchbolt, retracted position unless locked by key from either side • Lever/Knob inside retracts latchbolt • Latchbolt can be locked into retracted • There is no outside lever or knob position by the key from either side • Auxiliary deadlatch • Lever/Knob inside is always active • 7892 "T" turn is used in place of knob • Auxiliary deadlatch • Special cam required for inside cylinder • Latch hold back - set by rotating lever all • Latch hold back - set by rotating lever all the way down, then rotate key twice the way down, then rotate INSIDE key toward latchbolt. Lever will remain in twice toward latchbolt. Lever will remain rotated position for unlocked indication. in rotated position for unlocked indication. Double Cylinder with Deadbolt

!*‡26 Store Door *40 Classroom Security Intruder Deadbolt 8226, 7826 • Key from either side retracts and 8240, 7840 • Key either side retracts or projects deadbolt projects deadbolt to unlock or lock lever/knob outside • Lever/Knob from either side • Lever/Knob outside retracts latchbolt, retracts latchbolt except when outside lever/knob is locked • Latchbolt and deadbolt are independent by key of each other • Lever/Knob inside retracts both latchbolt • ANSI F14 and deadbolt simultaneously, and unlocks lever/knob outside • Auxiliary deadlatch • ANSI F34 29 Dummy Trim Deadlock 8229, 7829 • Deadbolt operation only • Key on either side retracts and projects deadbolt 41 Classroom Security Intruder Deadbolt • Lever/Knob inside retracts deadbolt 8241, 7841 • Key from either side retracts and projects deadbolt • Lever/Knob outside is always rigid • Key retraction of deadbolt, lever/knob outside remains locked • Key retraction of latchbolt from either side unlocks lever/knob outside *39 Classroom Security Intruder Deadbolt • Lever/Knob outside retracts latchbolt, except 8239, 7839 • Key either side retracts or projects deadbolt when outside lever/knob is locked by key or to unlock or lock lever/knob outside projecting deadbolt • Lever/Knob inside (when deadbolt is • Lever/Knob outside retracts latchbolt, projected) retracts both latchbolt and except when outside lever/knob is locked deadbolt simultaneously by key • Auxiliary deadlatch • Lever/Knob inside retracts both latchbolt and deadbolt simultaneously, and unlocks 7

lever/knob outside 0 0 2

• ANSI F33 , 5 0

46 Dormitory or Exit 0 2

8246, 7846 • Key from either side retracts and , 4 0

projects deadbolt 0 2 y

• Key from either side retracts both n a

latchbolt and deadbolt, lever/knob p m

outside remains locked o C g n

• Lever/Knob outside is locked by toggle or i r u

projecting deadbolt t c a • Lever/Knob outside is unlocked by toggle only f u n *8200 Available with Freewheeling Trim • Lever/Knob inside (when deadbolt is a M

‡7800 Available with Push/Pull Trim projected) retracts latchbolt and deadbolt T N ! simultaneously E

CAUTION: Not recommended for use on any door used for Life Safety egress G R A S

If shaded, knob or lever rigid at all times © 7 0 / 1 0 / An ASSA ABLOY Group company 13 3 7800/8200 Mortise Locks 1-800-727-5477 Functions www.sargentlock.com

!48 Store Door !49 Security Deadbolt 8248, 7848 • Key from either side retracts and projects 8249 • Key from either side retracts and deadbolt projects deadbolt • Key from either side retracts latchbolt • Key from either side retracts latchbolt • Lever/Knob outside is locked by toggle or • Levers/knobs inside & outside are rigid only projecting deadbolt and unlocked by when deadbolt is projected toggle only • Lever/Knob inside (when deadbolt is projected) retracts latchbolt only, and outside lever/knob remains locked • ANSI F25

!52 Institutional Deadbolt 8252, 7852 • Key from either side retract latchbolt • Key from either side retracts and projects deadbolt • Lever/Knob on both sides are always rigid • Auxiliary deadlatch

Non-Keyed

13 Exit Latch *66 Privacy Bedroom or Bath 8213, 7813 • No outside lever/knob or cylinder 8266, 7866 • Lever/Knob outside retracts latchbolt • Lever/Knob inside retracts latchbolt except when deadbolt is projected • Auxiliary deadlatch • Lever/Knob inside retracts both latchbolt • A Multi-Function Lock Body and deadbolt simultaneously, and unlocks outside lever/knob • ANSI F31 • Emergency Release retracts and projects deadbolt • Thumb turn retracts and projects deadbolt • ANSI F19 ‡15 Passage or Closet ! 8215, 7815 • Lever/Knob from either side retracts 68 Privacy Bedroom or Bath latchbolt at all times 8268, 7868 • Lever/Knob from either side retracts latchbolt at all times • ANSI F01 • Thumb turn inside retracts and projects deadbolt • Emergency release outside retracts and projects deadbolt • Latchbolt and deadbolt are independent of *‡ 65 Privacy Bedroom or Bath each other • ANSI F02 7 8265, 7865 • Lever/Knob outside retracts latchbolt 0 0

2 except when locked by thumb turn inside , 5

0 • Lever/Knob inside retracts latchbolt and 0 93 Trim Dummy 2

, unlocks outside lever/knob 4 8293, 7893 • Lever/Knob on inside of door is always rigid 0

0 • Emergency Release unlocks 2 • Lever/Knob only used as door pull y

n lever/knob outside a Note- Lever not surface mounted - see special p • Thumb turn locks and unlocks m door prep template # 4298 o

C lever/knob outside g n i • Closing the door will unlock r u t lever/knob outside c a f

u • ANSI F22 n a

M *8200 Available with Freewheeling Trim T N

E ‡7800 Available with Push/Pull Trim G

R !CAUTION: Not recommended for use on any door used for Life Safety egress A S © If shaded, knob or lever rigid at all times 7 0 / 1 0 / 3 14 An ASSA ABLOY Group company 7800/8200 Mortise Locks 1-800-727-5477 Functions www.sargentlock.com

94 Trim Dummy 96 Double Trim Dummy 8294, 7894 • Lever/Knob on both sides are always rigid 8296, 7896 • Lever/Knob on both sides are always rigid • Lever/Knob only used as door pull • Includes lock case and armor front Note- Lever not surface mounted - see special door prep template # 4298

95 Single Trim Dummy 8295, 7895 • Lever/Knob on one side only is always rigid 97 Active Trim Dummy • Includes lock case and armor front 8297, 7897 • Lever/Knob on both sides are active • Includes lock case and armor front

Deadbolt Only

!03 Classroom Deadlock !22 Deadlock 8203 • Deadbolt operation only 8222 • Deadbolt operation only • Key outside retracts and projects deadbolt • Key outside or inside retracts and • Thumb turn inside retracts deadbolt only, projects deadbolt will not project it • ANSI F16 • ANSI F29

!20 Deadlock !23 Classroom Deadlock 8220 • Deadbolt operation only 8223 • Deadbolt only operation • Key outside retracts and projects deadbolt • Key outside or inside retracts and • No inside operation projects deadbolt • ANSI F18 • Thumb turn inside retracts deadbolt, does not project deadbolt • Same as 03 function with an extra cylinder inside

!21 Deadlock 8221 • Deadbolt operation only 7

• Key outside retracts and projects deadbolt 0 0 2

• Thumb turn inside retracts and , 5 0

projects deadbolt 0 2 ,

• ANSI F17 4 0 0 2 y n a p m o C g n i r u t c a f u

*8200 Available with Freewheeling Trim n a

‡7800 Available with Push/Pull Trim M T

! N CAUTION: Not recommended for use on any door used for Life Safety egress E G R A If shaded, knob or lever rigid at all times S © 7 0 / 1 0 / An ASSA ABLOY Group company 15 3 8200 Mortise Locks 1-800-727-5477 Functions www.sargentlock.com

Electromechanical Functions

70 Electrical (Fail Safe) 77 Profile Series/Keypad Lock 71 Electrical (Fail Secure) with Deadbolt 8277 • Lever inside retracts latchbolt and 8270 • Solenoid activated mortise lock deadbolt simultaneously when deadbolt 8271 • 70 function - Power ON, locks outside is projected lever (by solenoid) • Lever outside active in “passage” mode or S A R G E N • 71 function- Power OFF, locks outside lever T with valid user code (by solenoid) • Lever outside (with deadbolt projected) • Key outside retracts latchbolt, when the active with Emergency Code or Master lever outside is locked Code • Lever outside retracts latchbolt except • Thumb turn retracts and projects deadbolt when lever outside is lock • Auxiliary deadlatch • Lever outside can only be locked with the • Used with Keypad and Low Profile Series solenoid Access Control Products • Lever inside always retracts latchbolt • For more information see the Profile Series • Auxiliary deadlatch Catalog and Keypad Catalog • KP8277 Shown

78 Profile Series/Keypad Lock with Cylinder !72 Electrical (Fail Safe) 73 Electrical (Fail Secure) 8278 • Key outside retracts latchbolt • Lever inside retracts latchbolt 8272 8273 • Solenoid activated mortise lock • Lever outside active in “passage” mode or with valid user code • 72 function - Power ON, locks both levers (by solenoid) • Auxiliary deadlatch • 73 function- Power OFF, locks both levers • Used with Keypad and Low Profile Series (by solenoid) Access Control Products • Key on either side retracts latchbolt, when • For more information see the Profile Series the lever are locked Catalog and Keypad Catalog • Lever from either side retracts latchbolt, • LU8278 Shown except when lever are locked • Lever on both sides can only be locked with the solenoid 79 Profile Series/Keypad Lock • Lever can not be locked separately, only 8279 • Lever inside retracts latchbolt together • Lever outside active in “passage” mode or • Auxiliary deadlatch with valid user code • Auxiliary deadlatch S A R G E N T • Used with Keypad and Low Profile Series 76 Profile Series/Keypad Lock Access Control Products with Deadbolt and Cylinder • For more information see the Profile Series Catalog and Keypad Catalog 8276 • Key outside retracts and projects deadbolt and retracts latchbolt • KP8279 Shown

7 • Lever inside retracts latchbolt and 0

0 deadbolt simultaneously when deadbolt 2 ,

5 is projected 0 0 2

, • Lever outside active in “passage” mode or 4

0 with valid user code 0 2 y • Lever outside (with deadbolt projected) n a

p active with Emergency Code or Master m

o Code C g • Thumb turn retracts and projects deadbolt n i r u

t • Auxiliary deadlatch c a f • Used with Keypad and Low Profile Series u n a Access Control Products M

T • For more information see the Profile Series N

E Catalog and Keypad Catalog G R

A • PK8276 Shown S © !CAUTION: Not recommended for use on any door used for Life Safety egress 7 0 / 1 0 / 3 16 An ASSA ABLOY Group company 7800/8200 Mortise Locks 1-800-727-5477 Strikes and Fronts www.sargentlock.com

• All strikes: Brass, bronze or stainless steel. • To order strikes separately, specify strike part number and finish • Strikes ordered separately are furnished with machine screws • Order strike box 77-1141 separately • All locks are packed standard with a universal non-handed curved lip ANSI 4-7⁄8"(124mm) strike. Outside Front Plate • Specify part number when ordering with complete lock • See chart below for part number and lip lengths Standard 1-1/4" 1-1/16" Functions • Open back strike not available for deadbolt functions (32mm) (27mm) Curved Lip Strike 82-0080 82-0235 15, 65 Door Thickness Part No. Lip Length 82-0081 82-0236 04, 05, 06, 13, 16, 17, Double Door 82-0229 7/8" (23mm) 31, 36, 37, 38, 67 1-3/8" - 1-1/2" 82-0109 1-1⁄8" (29mm) 82-0082 82-0237 03, 20, 21, 22, 23, 28, (35mm) (38mm) 29, 30 1-5/8" - 1-3/4" 82-0110 (Std) 1-1⁄4" (32mm) (41mm) (44mm) 82-0083 82-0238 24, 25, 26, 27, 35, 39, 66, 68 1-7/8" - 2" 82-0111 1-3⁄8" (35mm) (48mm) (51mm) 877 Open Back Strike 82-0084 82-0239 40, 41, 50, 52, 57 2-1/8" - 2-1/2" 82-0112 1-5⁄8" (41mm) • Strike handed by active leaf 82-0086 82-0241 45, 46, 47, 48 (54mm) (64mm) Part No. Part No. 82-0087 82-0242 43 2-5/8" - 3" 82-0113 1-7⁄8" (48mm) Door Thickness RHRB LHRB (67mm) (76mm) 82-0088 82-0587 89, 90, 91, 92 1-3⁄4" (44mm) 82-0332 82-0333 3-1/8" - 3-1/2" 82-0114 2-1⁄8" (54mm) 82-0578 82-0588 70, 71, 72, 73 (79mm) (89mm) 2" (51mm) 82-0334 82-0335 82-0578 – 78, 79 3-3/8" - 4" 82-0115 2-3⁄8" (61mm) 2-1⁄4" (57mm) 82-0336 82-0337 (86mm) (101mm) 2-1⁄2" (64mm) 82-0338 82-0339 82-0579 – 76, 77 4-1/8" - 4-1/2" 82-0116 2-5⁄8" (67mm) (105mm) (114mm) 2-3⁄4" (70mm) 82-0340 82-0341 82-0627 – 95, 96, 97 4-5/8" - 5" 82-0117 2-7⁄8" (73mm) 3" (76mm) 82-0342 82-0343 82-0085 82-0240 55 (117mm) (127mm) Curved Lip Strike (Standard) 877 Open Back Strike Outside Front Plate 11/16" (17mm) 1-1/4" or 1-1/16" (32mm) (27mm) ) ) ) m " m

" 4-1/8" "

8 1/8" m ⁄ m 8 4

⁄ 3⁄32"

⁄ 4-1/8" m 7 4

m (104.7mm) - 7

3 (3mm) 4 2 - - 0 (2mm) 4 (104.7mm) 2 1 4 2 7

( Thick 1 (

( Thick

) 6-1/2" m " m (165.1mm) 8 1-1/4" 3 ) 0 " (32mm) 2 m ( 4 ⁄ m

Lip Length 1 - 2 1 3 (

1-3⁄4"

(45mm) 7 0 0 2

78-0034 Deadbolt Strike , 5

77-1141 Wrought Box Strike 0 11/16" 0 2

(17mm) , 4 0 0

1-1⁄32" 2 (26mm) y n a p ) 1-1⁄2" No. 677 Rabbeted Door Kits m o m "

(38mm) C 8 4-1/8" ⁄ m 7 g 4 677 Kit adapts 7800/8200 locks for rabbeted - (104.7mm) n 2 4 i 1 r

( doors consists of rabbeted strip and strike. 3⁄32" u t Std for 1-3⁄4" to 2" doors. c (2mm) a f

Thick u Specify 2-677 for 2-1⁄4" thick doors. n a

Hardware Finished. M T

• For both curved and flat lip strikes N 1-1⁄4" E G

(32mm) • Optional- ordering with lockset R A • Provided standard with deadlock specify suffix WBS. S functions 03, 20, 21, 22, 23, 28, 29, 30 © 7 0 / 1 0 / An ASSA ABLOY Group company 17 3 8200 Mortise Locks 1-800-727-5477 Electrical Functions and Monitoring Options www.sargentlock.com

SARGENT 8200 Electromechanical Mortise locks are designed to handle single opening, stand alone applications, or can be readily integrated into sophisticated access control systems. They meet ANSI/BHMA A 156.13 Grade 1 requirements, are UL listed on fire doors, and satisfy industry standards for operating temperature, shock and fire hazard. • See Function Page 16 for full description of lock operation

Electrical Functions:

8270 8271 8272 8273 Applications: Security and restricted access areas in schools, computer rooms, offices, banks, equipment rooms, laboratories, pharmacies and hospitals. Also used with fire and alarm controls • Fail Safe • Fail Secure • Fail Safe • Fail Secure in buildings and stair tower doors. • Power On locks • Power Off locks • Power On locks • Power Off locks outside lever outside lever both levers both levers

Electrical Requirements: Warning: SARGENT Power Supplies Voltage: 12VDC or 24VDC Regulated. Full • Do not connect locks with a circuit • 3510 Power Supply, for up to a maximum wave rectification installed inside the sharing an additional electromagnetic of 7 locks – 24VDC, 1.8 Amp regulated lockbody. device as the lock may be damaged and filtered. UL Listed Class II Current: .25A at 24VDC or .5A at 12VDC • Transient voltage must be suppressed at the • 3530 Power Supply, for up to a maximum Operating Temp.: Max. 151°F (66°C), source or before connecting with the lock of 8 locks – 24VDC, 2 Amp regulated Min –31°F (-35°C) • Varistor rated at 35 volts (peak) may be and filtered. UL Listed UL and CUL listed for use on Fire Doors used for transient voltage protection • 3560 Power Supply, for up to a maximum Note: Repeated operation at voltage of 28 locks – 24VDC, 7.2 Amp regulated Note: Opening the lockbody or the solenoid exceeding +/- 10% is not recommended. and filtered. UL Listed replacement in the field by non-authorized personnel voids UL label and lock warranty.

RX, LX, and DX Monitor Switch Prefixes for 8200 Mechanical Mortise Locks

8200 Electromechanical Mortise Lever Locks are available with internal switches for independently monitoring inside/outside lever rotation (RX-), latch position (LX-) and deadbolt position (DX-).

• SPDT type C switches, rated 2A at 24VDC • RX- Request to Exit or Enter – Two switches mounted internally in lockbody that provide independent monitoring of inside and outside lever rotation – Available in all functions w/non rigid levers – Not available for the following prefixes: 1-, 3P, 74 7

0 – Not available for the following trims: LS or FE 0 2 ,

5 • LX- Latchbolt Monitor 0 0

2 – Single switch mounted internally in lockbody that indicates ,

4 latch retraction 0 0 2

y – Available for all non deadbolt functions n a – Not available with DX p m o • DX- Deadbolt Monitor C g – Single switch mounted internally in lockbody that indicates n i r

u deadbolt retraction t c

a – Not available for the following prefixes: 3P-, 74 or LX f u

n – Available in all deadbolt functions a M T N E G R A S © 7 0 / 1 0 / 3 18 An ASSA ABLOY Group company 7800/8200 Mortise Locks Turns, Emergency Release 1-800-727-5477 and Indicators www.sargentlock.com

130KB - Use with 8200 Rose Trim 126 T-Turn (7892 function only) • 1-1/2" (38mm) round brass, bronze • Brass or bronze or stainless steel plate ) )

" • Finishes: 3, 4, 9, 10, 10B, 10BL, 20D, 8 m 6 m e n / s r 1 3 / m m o

u 26, 26D - 3 1 6 T 2 R - 6 5 2 ( ( • Surface mounted with three screws • Order as “SSTT” trim with 7892 function

130W - Use with 7800 Rose Trim Emergency Key 14-0057 • Carbon steel • 1-1/2" (38mm) round brass, bronze • For bathroom/privacy function only or stainless steel plate • Must be ordered separately

184W Emergency Release • 1-1/2" (38mm) round brass, bronze 130KA - Use with E Rose or stainless steel plate • 1-1/2" (38mm) square brass, bronze or stainless steel plate

184KB Emergency Release • 1-1/2" (38mm) round brass, bronze or stainless steel plate 130LB - Use with 8200 Rose Trim

• 40% larger than standard thumb turn • 2" (51mm) round brass, bronze, or stainless steel plate & turn 184KA Emergency Release • Furnished with flat spindle • 1-1/2" (38mm) square brass, bronze or stainless steel plate

Lock Status and Secured Rose Indicators for 7800 and 8200 Mortise Locks 49- Prefix Visual Status Indicator 49- Prefix Occupancy Indicator for Non Secure Applications with Emergency Release 50- Prefix Secured Indicator Rose

• Designed to work Inside Only • Ideal for restrooms or • Non-handed with with Classroom conference rooms where lever and mounting Security functions easy determination of posts field reversible • Red/White indicator use needs to be made • VAC/OCC indicator 7 0

plate standard, field • OCC/VAC indicator plate plate standard, field 0

185P 2 replaceable OCC/VAC 185C standard, field replaceable replaceable Red/White , 5 0

plate included Red/White plate included plate included 0 2 , 4

• Mounts on inside of door • Mounts on outside of door • Mounts on outside of door 0 0 2

• Not available in escutcheon trim • Not available in escutcheon trim • Not available in escutcheon trim y n a • 7800 & 8200 Functions and roses • Emergency coin operated release • Available for the following functions: p m o

available: standard 24, 25, 26, 28, 29, 30, 36, 37, 38, 39, 40, C g

— 30, 36 & 37 Function: CR, L, LN, 41, 43, 45, 50, 51, 52, 67 n • As retrofit, order 185P x finish i r

TR, E and O u t

• Patent pending design c

• 7800 & 8200 Functions and roses a — 26, 29, 38, 39, 40 and 41 Functions: LN f available: • For retrofit, order 185S x suffix x finish: u n • As retrofit, order 185C x finish -65, 66, 68 Function: CR, E, L, LN, O, TR a Suffix Door Thickness M T

Note: For 49- and 50- Prefixes, key will -1 1-3/8" (35mm) N E G

not retract latch when used with -2 1-3/4" (44mm) R A

37 and 38 functions. -3 2" (51mm) S -4 2-1/4" (57mm) © 7 0 / 1 0 / An ASSA ABLOY Group company 19 3 7800/8200 Mortise Locks 1-800-727-5477 Cylinders www.sargentlock.com

Cylinder Lengths (Dim X)

Cylinder No. 41 42 43 44 46 48 50 52 54 56 Dim X 1-1/8" 1-1/4" 1-3/8" 1-1/2" 1-3/4" 2" 2-1/4" 2-1/2" 2-3/4" 3" Length Under (29mm) (32mm) (35mm) (38mm) (44mm) (51mm) (57mm) (64mm) (70mm) (76mm) Cylinder Head

40 Series Type Cylinder

• Cylinder body: Solid brass 1-5/16" 15⁄32" • Cap: Brass, bronze or stainless steel (33mm) (12mm) • All functions take a Standard Cam shown Except 16, 50 & 92 (see page 22 for more details) 1⁄8" Dim X (3mm)

7850/8250 Function Hotel Cylinder VA- Prefix SARGENT V-10 • When door is locked by deadbolt, • Patented high security cylinder only emergency key is able to unlock protects against unauthorized key • Must request emergency key duplication separately (14-0036 x keying info) • Master keying capabilities up to • See cam design on page 22 160,000 changes • UL Listed • VC Prefix- V-10 removable core 78- Prefix Exposed Barrel • VS Prefix- V-10 standard unassembled • VSVC Prefix- V-10 removable core • Standard for use only with SARGENT unassembled Escutcheon Trims KE3, KE4, LE3, LE4 • Cylinder always ships separately • Available 6pin standard or 7 pin optional • NOT available with 50-, 60-, 70- or other specialty or higher security options • See function table for cam required F1-82- and 82- Prefix KESO • Not available in 50 function • The system offers the building owner • Plug finishes: 4, 15 (similar to 26 finish) full control over duplication of keys • Highly pick resistant cylinders 124 Series Mortise Cylinder Turn Lever • Expanded levels of masterkeying • F1-83- & 83- Prefix- Keso removable core • Turn lever: Brass, bronze or aluminum • 84- Prefix- Keso construction core • Cap: Brass, bronze or stainless steel cylinder • Must be ordered separately 7 0 0

2 11- Prefix XC Key System , 5 0 0

2 • Patented system works with ,

4 10- Prefix Signature Series existing SARGENT keyway 0 0

2 adding increased security

y • The patented system offers the n a building owner full control over • 11- XC Std Cylinder p m duplication of keys. o • 11-73- Small Format C Highly pick resistant cylinders g Interchangeable core n i r • 10-63 Prefix- Signature cylinder in u t c

a removable core f u n

a • 10- UL Prefix- Signature cylinder

M that meets UL437 requirements T

N for security E G R A

S For complete cylinder information, see Cylinders & Components, Signature, Keso, Keso F1, XC or V-10 catalogs. © 7 0 / 1 0 / 3 20 An ASSA ABLOY Group company 7800/8200 Mortise Locks 1-800-727-5477 Cylinders and Rosettes www.sargentlock.com

51- Prefix Old Style Removable Core 21- Prefix Lost Ball Construction System • Available for existing systems only • The SARGENT construction keying system protects the building Permanent Removable Cores owner by providing temporary masterkeying during the construction period • Control key used to remove core, must request control key separately 1KB Rosette with 8200 Rose Trim

60- or 70- Prefix Plastic Construction Core • Used with mortise cylinders and No. 90 blocking rings when cylinders • For doors that do not require key project from door locking during the construction • Furnished standard with 8200 rose period design lever mortise trim • Operate with coin or flat screw • Brass, bronze or stainless steel driver • 1-1/2" (38mm) diameter, includes • For use with removable (60- Prefix) compression spring or interchangeable (70- Prefix) core • Projection from door: 1KB-1 5/16" (8mm) - Standard 63- Prefix Removable Core 1KB-2 7/16" (11mm) • Allows immediate removal of the 1KB-3 9/16" (14mm) core. Virtually unlimited key changes • Finishes: 3, 4, 10, 10B, 10BL, 20D, 26, • For disposable core, see 60- prefix 26D, 32, 32D • 64- Prefix- removable 6 pin construction core No. 97 Rosette with 7800 Rose Trim • Control key used to remove core, • Standard for cylinders ordered must request control key separately separately from hardware • Standard for 7800 knob mortise & 7300B Interchangeable Core 4870 deadbolt • Brass, bronze or stainless steel • Small Format Interchangeable Core • 1-11/16" diameter (43mm), 9/32" • SARGENT Interchangeable Core (7mm) projection, includes cylinders and MasterKey Systems are compression spring available for increased security through quick change of keying. It is • Finishes: 3, 4, 10, 10B, 10BL, 20D, 26, unnecessary to remove a cylinder 26D, 32, 32D • SARGENT 7300B Interchangeable Cores No. 90 Blocking Ring are available in SARGENT 4A and 4B keyways, as well as the following • Used with 1KB rosettes as spacer standard competitor keyways: A, B, C, when mortise cylinder projects D, E, F, G, H, J, K, L, M from face of door • For disposable core, see 70- prefix • Brass, bronze or stainless steel • 65-73 Prefix- 6 Pin Small Format • 1-3/8" (35mm) diameter; 1/16" Interchangeable Cores-uncombinated (1.6mm) to 3/8" (9mm) projection in 1/16" (1.6mm) increments. • 65-73-7P Prefix- 7 Pin Small Format Specify size when ordering. Interchangeable Cores-uncombinated • Finishes: 3, 4, 10, 10B, 10BL, 20D, • 70- Prefix- Small Format 26, 26D, 32, 32D Interchangeable disposable core 7 0

• 72- Prefix- Small Format 0 2

Interchangeable construction core 77-4230 Cylinder Retaining Cap , 5 0 0

• 11-72- Construction core provided for • Required for double cylinder functions 2 , 4

use with 11-7300 cylinder housing on KS and LS Escutcheon only 0 0 2

11-70- temporary plastic core • Steel or stainless steel y n a

prepared to accept 11-7300 core p • 1-15/32" (37mm) diameter m o

• 73- Prefix- 6 Pin Small Format C • 9/16" (14mm) projection g

Interchangeable core, SARGENT 4A, n i r

4B only for new systems • Finishes: 3, 4, 9, 10, 10B, 10BL, 20D, u t c

26, 26D, 32, 32D a f

• 73-7P Prefix- 7 Pin Small Format u n

Interchangeable core, SARGENT 4A, a M

4B only for new systems T N E

• Control key used to remove core, G R

must request control key separately A S © For complete cylinder information, see Cylinders & Components, Signature, Keso, Keso F1, XC or V-10 catalogs. 7 0 / 1 0 / An ASSA ABLOY Group company 21 3 7800/8200 Mortise Locks 1-800-727-5477 Cylinders Requirements and Cams www.sargentlock.com

Escutcheon Trim Rose Trim CE, KE 1 & 2, KW1 or Design LE 1 & 2 or TE LW1 KE 1 & 2 or LE 3 & 4 KS or LS WT CR,E,O,L,LN or TR E, L or O (Exposed Barrel) 78-40 Cylinder Cylinder Single Double Single Double Single Double Single Double Single Double Single Double Application Cylinder Cylinder Cylinder Cylinder Cylinder Cylinder Cylinder Cylinder Cylinder Cylinder Cylinder Cylinder

Door 1-3⁄8 1-3⁄4 2-1⁄4 1-3⁄8 1-3⁄4 2-1⁄4 1-3⁄8 1-3⁄4 2-1⁄4 1-3⁄8 1-3⁄4 2-1⁄4 1-3⁄8 1-3⁄4 2-1⁄4 1-3⁄8 1-3⁄4 2-1⁄4 1-3⁄8 1-3⁄4 2-1⁄4 1-3⁄8 1-3⁄4 2-1⁄4 1-3⁄8 1-3⁄4 2-1⁄4 1-3⁄8 1-3⁄4 2-1⁄4 1-3⁄8 1-3⁄4 2-1⁄4 1-3⁄8 1-3⁄4 2-1⁄4 Thickness (35) (44) (57) (35) (44) (57) (35) (44) (57) (35) (44) (57) (35) (44) (57) (35) (44) (57) (35) (44) (57) (35) (44) (57) (35) (44) (57) (35) (44) (57) (35) (44) (57) (35) (44) (57)

41 Size 1-1/8" B B B E F E D F E (29mm) C — — NA C C NA NA C NA C — NA — — C C — J C — D — — A — — H H H H H H H H H Cylinder J J J 5 or 6 Pin 42 Size B F F 1-1/4" B B B H F D F D D F (32mm) C J C NA — C NA NA — NA C C NA M — H C — H — D J D A J A K H K J K G K K G K Cylinder K K K 5, 6, or 7 Pin 43 Size 1-3/8" B F F (35mm) B B B B J F E F E D E F A C J NA — C NA NA — NA — C NA — M K G C K D J A J L H C L H L H Cylinder J L L K J L L J L L 5, 6, or 7 Pin

NOTE 41 size cylinders include: Conventional, Signature, Signature UL, XC 42 size cylinders include: 50 function cylinders, SARGENT removable core, KESO removable core, KESO F1 removable core, ASSA V-10 removable core, Signature removable core 43 size cylinder include: Small Format Interchangeable Core

How To Find Rosette and Blocking Ring Requirements when ordering separately Rosettes and ring requirements are coded A. Part # 97 Rosette (includes spring) G. Part # 90-1/16" (2mm) Blocking Ring by letters A through M in the table to the B. Part # 97-02 (13-0140) Spring only H. Part # 90-1/8" (3mm) Blocking Ring right and depicted in chart above. C. No Spring, rosette or blocking J. Part # 90-3/16" (5mm) Blocking Ring For example: A #41 cylinder for a 1-3/8" ring required (35mm) door using KE1 escutcheon trim K. Part # 90-1/4" (6mm) Blocking Ring for a single cylinder application would D. 1KB-1 Rosette (includes spring) L. Part # 90-3/8" (10mm) Blocking Ring require (B) a No. 97-02 spring and (H) E. 1KB-2 Rosette (includes spring) Part # 90-1/8" Blocking Ring. M. Part # 81-0495 Cylinder Retaining Cap F. 1KB-3 Rosette (includes spring) Cylinder Cams For Mortise Locks

SARGENT Conventional Cylinders SARGENT Removable Core Cylinders • Standard • 60- Prefix 7 0 0 2 , 5 0 0 2 , 4 0 0 2 y n a p 13-0664 13-0665 13-2045 13-0542 13-0806 13-1320 m

o Standard 16 & 92 50 Function Standard 16 & 92 50 Function C SARGENT Function Hotel Cam, SARGENT cam Function Hotel Cam, g n i

r cam except Inside requires except for Inside requires 50 u t 50 function Cylinder 50 function 50 function Cylinder function c a f locks and the Cam cylinder locks and the Cam cylinder u n Inside cam Inside cam for a

M for 16 & 92 16 & 92 T

N function function locks E

G locks R A S

© For cylinders other than conventional and removable core, see Cylinder catalogs for additional information 7 0 / 1 0 / 3 22 An ASSA ABLOY Group company 7800/8200 Mortise Locks 1-800-727-5477 Prefixes and Options www.sargentlock.com

Prefix Designation And Description

* *15 1-1/16" (27mm) wide front for 1-3/8" (35mm) doors (93 + 94 function only available as a special) (not available in KS, LS trim) * *3 Stainless steel hubs (2) for institutional specification *• 105 Signature System (6"(152mm) door thickness max.) *• 10UL5 Signature Systems meeting UL437 (Security Grade 1) (3-1/4" (82mm) door thickness max) +•115 SARGENT XC Key System Note: Prefix not available with 10-, 22-, 60-, 64-, SC- or SE- prefixes *•215 SARGENT Construction Key System (lost ball) standard on all new systems (3-1/4" (82mm) door thickness max.) *•225 SARGENT Construction Key System (split key). For pre-established split key systems only (2" (51mm) door thickness max.) *• 23 Flat Lip 4-7/8" (124mm) ANSI Strike **31 For doors 1-7/8" (48mm) to 6" (152mm) thick –see cylinder prefix for limitations on door thickness. MUST SPECIFY: A: Total thickness of door and location of the lock within the door, specify MUST specify PANEL size and location (inside or outside) on door. MUST Consult Factory if cylinder/key is other than standard Sargent cylinder -since not all cylinders are available in larger sizes. •• 36 ** 6 Lobe head security screws (Torx type) (not available on LE3 or LE4 escutcheon’s small set screw) *•* 37 ** Spanner head security screw (not available on LE3 or LE4 escutcheon’s small set screw) 49 Visual & Occupancy Indicators 50 Secured Indicator rose for doors 1-5/8" (41mm) to 2-1/4" (57mm) thick • 51 5 Old style removable core cylinders (existing systems only) (3-1/4" (82mm) door thickness max.) • 52 5 Old style construction cores cylinders (existing systems only) (3-1/4" (82mm) door thickness max.) *• 60 Disposable construction core (3-1/4" (82mm) door thickness max.) *• 63 SARGENT removable core cylinder (3-1/4" (82mm) door thickness max.) Request control key separately *• 64 SARGENT removable construction core cylinder (3-1/4" (82mm) door thickness max.) Request control key separately •• 65-735 Small format Interchangeable Cores – 6 pin uncombinated (2-1/2" (63mm) door thickness max.) •• 65-73P5 Small format Interchangeable Cores – 7 pin uncombinated (2-1/2" (63mm) door thickness max.) 68 Lever outside x knob inside, excludes detention knobs; consult factory for details 69 Lever inside x knob outside, excludes detention knobs; consult factory for details •• 705 Small format Interchangeable Core (6 or 7 Pin), plastic disposable core provided (2-1/2" (63mm) door thickness max.) •• 725 Small format Interchangeable Core with construction core provided (2-1/2" (63mm) door thickness max.) Request control key separately •• 735 Small format 6 Pin Interchangeable Core SARGENT 4A, 4B keyway only. (2-1/2" (63mm) door thickness max.) Request control key separately •• 73-7P5 Small format 7 Pin Interchangeable Core SARGENT 4A, 4B keyway only. (2-1/2" (63mm) door thickness max.) Request control key separately *• 74 Lead lined case, and/or rose. Rose specify inside, outside or both. Not available for escutcheons ** 75 Inside trim only. Milled levers or knurled knobs (7800 “B” and “C” knobs only) ** 76 Outside trim only. Milled levers or knurled knobs (7800 “B” and “C” knobs only) ** 77 Both inside and outside trim. Milled levers or knurled knobs (7800 “B” and “C” knobs only) 81- Cylinder to accept Keso (83) and Keso F1 (F1 83) removable core - no core provided *• 82 Keso security cylinder (For existing systems only) (3" (76mm) door thickness max.) **•F1-825 SARGENT Keso Security Cylinder with Front Profile patent pending (3" (76mm) door thickness max.) ••835 Keso security system removable core cylinders (3" (76mm) door thickness max.) •• F1-835 SARGENT Keso Security Removable Core Cylinder with Front Profile patent pending (3" (76mm) door thickness max.) •• 845 Keso security removable construction core cylinder (3" (76mm) door thickness max.) AV Anti-vandal Pull trim DX Deadbolt Monitoring (Not available with 3P, 74, LX, or any non-deadbolt function) • LB Larger size ADA thumb turn LX Latch monitor switch, available for all 8200 non-deadbolt functions only RX Request to exit. Monitors the activation of the inside and outside lever independently on 8200 only ••SC5 Lock furnished in Schlage “C” Keyway Number 41 cylinder only, 0 bitted (2" (51mm) door thickness max.) ••SE5 Lock furnished in Schlage “E” Keyway (Specify), Number 41 cylinder only, 0 bitted (2" (51mm) door thickness max.) SG MicroShield™ - An antimicrobial clear powder coat 7

TL SARGuide Illuminated inside WT trim with the word EXIT illuminated. (4-1/2" pocket depth required) see pg 3 for details 0 0 2

*• VA SARGENT V-10 standard cylinder (3-3/4" (95mm) door thickness max.) ,

5 5 0

•VC SARGENT V-10 Removable core (2-1/4" (57mm) door thickness max.) 0

5 2 ,

*• VS SARGENT V-10 cylinder unassembled (3-3/4" (95mm) door thickness max.) 4

5 0 0 • VCVS5 SARGENT V-10 Removable core cylinder unassembled (2-1/4" (57mm) door thickness max.) 2 y n a p m

* Prefixes available with Freewheeling Trim (Consult factory if thicker than 1-3/4 (44mm) thick door) o C

** See screw chart on back page g n i • Prefixes available with Push/Pull trim r u t c

5 Cylinder prefixes not available with standard 50 function lockout cylinder a f u n a M

NOTES: Interchangeable core and removable core cylinders do not meet Security Grade 1 requirements. T N

Split finishes available (Order: outside finish/inside finish) E G

If inside and outside trim designs differ, please specify (Order: outside trim/inside trim) R A S © 7 0 / 1 0 / An ASSA ABLOY Group company 23 3 7800/8200 Mortise Locks How To Order, Finishes, Packaging & 1-800-727-5477 Security Screw Chart www.sargentlock.com

How to Order Specify Note Example Quantity Numbered Ordered 1 Qty Prefix * Additional Feature 1 Qty 10-SG- Lock Function See Functions 1 Qty 10-SG-8271 Voltage 12V or 24V 70,71,72 & 73 require voltage callout 1 Qty 10-SG-8271-24V Trim Design Rose x Lever 1 Qty 10-SG-8271-24V LNL Finish & Hand of Door See Finishes 1 Qty 10-SG-8271-24V LNL 26D LHRB Additional Information Item/Heading Number, Door 1 Qty 10-SG-8271-24V LNL 26D LHRB Number, Keyset Information x Item 01 x DRL201 x Keyset AA3 Multiple prefixes available Finishes US Finish Description ANSI/BHMA *•+ 3 Polished brass, clear coated 605 *•+ 4 Satin brass, clear coated 606 *•+ 9 Polished bronze, clear coated 611 *•+ 10 Satin bronze, clear coated 612 *•+ 10B Oxidized bronze, oil rubbed 613 *+ 10BL Oxidized satin, bronze, clear coated — *+ 15 Satin nickel, clear coated 619 *+ 20D Statuary dark bronze, clear coated — *+ 26 Polished chrome 625 *+ 26D Satin chrome 626 •+ 32 Polished stainless steel 629 •+ 32D Satin stainless steel 630

* Finishes available with 8200 Coastal Series™ Trim and 8200 Freewheeling Trim • Finishes available with 7800 Push/Pull Trim + Finishes available with Studio/Metro Series trim (also available in 14 finish for this trim MicroSheild - optional designate SG- prefix (Available on all finishes listed except 10B or 20D)

6 Lobe & Spanner Bit packs Part Number Descriptions 82-3855 6 Lobe Bit Pack 6 bits (sizes- T8, T9, T10, T15, T20, T25, T27) 9/32" Driver 82-3856 Spanner Bit Pack 5 bits (sizes- 6, 8, 10, 12, 14) 1/4" Driver

Packaging 8205 x LNL approx. 6.1 lbs. (2.7kg)/box 6 boxes/case 8205 x WTL approx. 7.2 lbs. (3.1kg)/box 6 boxes/case 36- or 37- Prefix Security Screw Chart 7 0 0

2 Functions , 5

0 Trim Designs 3 4 5 6 13 15 16 17 20 21 22 23 24 25 26 31 35 36 37 38 39 40 41 43 45 50 65 66 70 71 72 73 85 86 87 91 92 93 94 0 2 ,

4 E, L, LN, O Roses 5565555545456655555555566677–––––––5544 0 0 2 PT - Push/Pull –6–––555––––6–5–––5555566677––––––––––– y n a p LE/KE (1&3) & LW1/KW1 67777777666677777777777777777777–––7766 m o

C LE/KE (2&4) 455555––44––55–5555––––55–5555–––––5544 g n i r FE - Freewheeling –7–––––7–– ––77777–7777– ––777––––777–––– u t c a LS/KS 89999999888899999999999999999999–––9988 f u n a WT 12 13 13 13 9 13 13 13 8 12 12 13 13 13 13 13 9 9 13 13 13 13 13 13 13 13 13 13 13 13 13 13 – – – 13 13 12 12 M T

N Quantities are per lock x function x trim design. E G

R Please note: Two small set screws on LE/KE (3 & 4) that hold inside escutcheon scalp onto casting and the screw on the edge of door for A S 93 & 94 functions are not available in security type screws, but are available and listed above. © –Trim design is not available with this function. 7 0 / 1 0 / 3 24 An ASSA ABLOY Group company 7800/8200 Mortise Locks 1-800-727-5477 Suggested Architectural Specifications www.sargentlock.com

2.1 HEAVY DUTY MORTISE LOCKS DOOR HANDING - Changing Lock Hand (standard) U.S. Patent No. 5,678,870 Note: To change the hand of the lockbody 1. Changing a lockbody from LH to RHRB A.Heavy duty mortise locks shall be 7800/8200 Series as manufactured by is either a 1 or 2 step process depending or RH to LHRB or the opposite requires SARGENT Manufacturing Company, New on the hand of the lockbody and what only step (A) to be performed. Haven, CT. hand it needs to be. Remember the RED 2. Changing a lockbody from LH to LHRB surface of the locking piece (step A) B.Locks shall meet or exceed the or RH to RHRB or the opposite requires requirements of ANSI/BHMA A156.13 always faces the locked or outside surface only step (B) to be performed. of the door. The bevel on the latchbolt Series 1000, Operational Grade 1, and 3. Changing a lockbody from LH to RH or Security Grade 1 with all (step B) must always face the strike. standard trims. RH to LH or the opposite requires both step (A) & (B) to be performed. C.Meets or exceeds impact requirements of ASTM F1577-95b Detention Locks for Swinging Doors. Door Handing 1. Paragraph 6.2 Level 1 Impact for deadbolt x latchbolt and deadbolt only. 2. Paragraph 6.2 Level 3 Impact for latchbolt only. D.Locks shall be easily re-handed without opening the lock body. E. Locks shall comply with UL10C and UBC 7-2 positive pressure requirements. F. Locks required for fire doors shall be listed by Underwriters Laboratories for ratings of A label (3 hours) and less, for doors up to 4'0" (1.2m) x 8'0" (2.4m) and pairs of doors 8'0" (2.4m) x 8'0" (2.4m). G.Construction: 1. Lock functions shall be manufactured in a single-sized case To change hand of locking piece To change hand of latch and guardbolt: formed from 12 gauge steel minimum. Note: The following Functions (04, 06, 1. Insert the blade of a slotted 16, 17 & 31) require that the Green Catch screwdriver (>1/4") into the spade 2. Lock cases shall be closed on all sides and back. Screw is removed prior to rotating the shape slot behind latch. Locking Slide. 3. Locks shall have field adjustable, 2. Rotate the screwdriver 90° to push beveled, armored front, with a .125 1. Position Lock Body so the Red latchbolt out until back of bolt clears inch (3mm) thickness minimum. Surface of the Locking Slide is facing lock case front. you. 4. Locks shall have a one piece, 3/4" 3. Rotate latchbolt 180° until the inch (19mm) throw anti-friction 2. With Blade Type Screw Driver, push latchbolt drops back into the stainless steel latch. on the Red surface of the locking lockbody. Slide so it rotates towards the back 5. Deadbolts, where specified, shall be of the lock. full one inch (25mm) throw made of one-piece hardened stainless 3. Continue to Rotate the Locking Slide steel. for a full 180 degrees, so that the 6. Where required by the Federal Red Surface is visible on the opposite Bureau of Prisons, locks can be side of the lock. furnished optionally with stainless 4. RED indicates locked (outside) side. steel hubs. H.Locks shall have a 2-3/4 inch (70mm) Insert screwdriver

backset, standard. blade into the spade 7 0 0

I. Strikes shall be non-handed with a shape slot 2 ,

curved lip. 5 0 0 2

J. To ensure proper alignment, trim, knobs , 4

or levers, shall be through-bolted and 0 0 fully interchangeable between rose and 2 y n

escutcheon. Lock front a p

K.Locks shall have brass 6-pin cylinder, Latch m o standard. Rotate screwdriver 90º C g

to push latch out until back n i K.Locks shall have a 10 year limited of latch clears lock front, then rotate latch 180º, r u

Red color latch will then re-enter lockbody t warranty. 2 year limited warranty on c

(Note: Latch can not be unscrewed) a

indicates locked f

electrified locks. u

side of door or n Locking a

hold back side M

piece slot (91 and 92 Functions) T N E G R A S © 7 0 / 1 0 / An ASSA ABLOY Group company 25 3 7800/8200 Mortise Locks 1-800-727-5477 Multi-functional Lockbody Options www.sargentlock.com

How to Change Lock Function: The Green Catch Screw must be located in the designated location as specified on the lock case to produce the desired function. There are three locations: one location for 05, 37 & 38 functions; one location for 04, 06, 13, 17 & 31 functions; and one location for 36 function. Note: When relocating the green catch screw to produce the following Functions 04, 06, 13, 17 & 31, the hub must be at the 45° position as specified on the case before screwing in the green catch screw. Note: For 17 and 52 functions only, the red locking piece must be rotated 90°, so the red surface is facing the back of the lockbody. This is required to make both levers rigid.

Function & Part Listing for the Multifunction Lockbody

Function #41 Cylinder Cyl. Collars Lever/Knob Requirements Thumb turn ** Inside Trim Set & 04 Store Room / Closet (F07) 1 * 1 - 1KB Not used *** Outside Trim Set ** Inside Trim Set & 05 Office / Entry (F04) 1 * 1 - 1KB ++ 1 *** Outside Trim Set + Trim One Side Kit, Inside 06 Store Room / Service 1 * 1 - 1KB Not used Lever/Knob & Rose/Escutcheon + Trim One Side Kit, Inside 13 Communicating / Exit Not used Not used Not used Lever/Knob & Rose/Escutcheon ** Inside Trim Set & 17 Asylum / Institution (F30) 2 * 2 - 1KB-2 Not used *** Outside Trim Set + Trim One Side Kit, Inside 31 Utility 1 * 1 - 1KB Not used Lever/Knob & Rose/Escutcheon + Trim One Side Kit, Inside 36 Closet 1 * 1 - 1KB Not used Lever/Knob & Rose/Escutcheon ** Inside Trim Set & 37 Classroom (F05) 1 * 1 - 1KB Not used *** Outside Trim Set ** Inside Trim Set & 38 Classroom Security (F32) 2 * 2 - 1KB-2 Not used *** Outside Trim Set

*Cylinder Collars–noted are based on 1-3/4" Thick Doors with standard #41 size cylinders. Other sized doors and cylinders will required different collar sizes and possibly blocking rings - see chart on page 22 of this catalog for details. ** Inside trim sets include: Inside lever/knob, inside rose or escutcheon, trim pack (spindles, through-bolt screws, set screw, inside adapter plate assembly),trim finish screws (for escutcheons). *** Outside trim sets include: Outside lever/knob, outside rose or escutcheon, outside mounting plate, two through-bolt studs, washers, retaining nut, and cylinder rosettes (for cylinder functions only). + Trim One-Side Kit includes: adapter assembly, spindle, thrubolt screws and plate adapter assy. An inside lever is always used with this kit and is used on either side of the door as required. ++ Thumb turn- Rose trims use 130KB thumb turn for Levers, and 130W thumb turn for Knobs. Escutcheon trims require escutcheon to be ordered according to function/design, to receive thumb turn affixed to it.

Type of Rose/Escutcheon Kit Part Number

Trim One Side Kit E,O, KW, LN & LW1 82-3208 Trim One Side Kit KE Series & LE Series 82-3209 Trim One Side Kit L Rose & WT 82-3210

Founded in the early 1800’s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes commercial construction, institutional, and industrial markets. © SARGENT Manufacturing Company 2004, 2005, 2007 ASSA ABLOY is the world’s leading manufacturer and supplier of locking solutions, meeting tough end-user demands for safety, security and user friendliness.

90115-4/07