20#4-Fold Screen V18G12.Cdr
Total Page:16
File Type:pdf, Size:1020Kb
4-Fold BathScreen Installation Instructions ●Please read these instructions in full before installing. IMPORTANT ●Check that the bath has been installed to the manufacturer’s instructions. ●Opening wall adjustments 4-Fold Bath Screen - adjustment =44"-42"(1108-1118mm) GENERAL SAFETY INSTRUCTIONS ●Do not fix the wall profile to newly plastered, painted or papered walls as chemical reaction may cause discolouration to the surface finish. ●lmportant: The wall plugs included in this pack are for solid walls only. If the product is to be mounted on a partition or stud wall, specialised fixings should be purchased separately. ●Fixing tips; A piece of insulating tape or a couple of layers of masking tape applied to the wall before marking out the fixing holes will help stop the drill from wandering, particularly on tiled surfaces. ●When working near a basin or bath insert the plug into the waste, this will help you avoid losing small parts. Also take care not to drop accessories or tools onto the bath or basin, use a towel or bathmat to protect delicate surfaces. ●CAUTION! Before drilling into any walls check that there are no hidden cables or pipes. Exercise great care when using power tools near water. The use of a residual current device (RCD) or cordless drill is recommended. Always double check the positioning and measurements before drilling holes. ●This product is heavy and requires two people during lifting and operations. ●Glass is delicate, support on cardboard to minimise risk of damage. Tools required (not supplied) Electric drill Tape measure Drill(Ø3.2mm) Rubber hammer Drill(Ø6mm) Knife Cross head screw driver Pencil Spirit level Silicone sealant SILICONE 1 IDENTIFICATION OF PARTS N4FS08 N4FS07 N4FS06 N4FS05 N4FS10 N4FS04 N4FS09 N4FS01 N4FS02 N4FS03 Fixings & fittings supplied Item No.: Part Quantity Item No.: Part Quantity N4FS01 x 1 N4FS07 x 1 N4FS02 x 1 N4FS08 x 9 N4FS03 x 1 N4FS09 x 4 x 4 N4FS04 ST4X10 N4FS10 x 4 x 4 SILICONE N4FS05 N4FS11 GREASE ST4X40 x 1 N4FS06 x 4 2 LH RH Four fold bath screen is ok to be installed in left hand or right hand. Below steps are based on left hand. For right hand, please follow below steps in mirror direction. Put top cover(N4FS08) on the top of the pivot of the N4FS08 N4FS02 - 1. screen frame(N4FS02). 9X 1X N4FS08 N4FS02 N4FS02 3 - Loosen the screw in the bottom of the vertical profile, N4FS03 remove the bottom bracket. - Cut the soft edge of the seal N4FS03 by 3"(75mm) on one end. 2. - Insert the seal into the bottom aluminum frame. - Tie off the end of the seal keep it from moving. 1X - Put the bottom cap on the vertical profile, fix it with screw. Note: Please observe cut required. 3"(75mm) N4FS02 - Put the wall profile(N4FS01) against the wall and N4FS01 ensure it is vertical using a spirit level. 3. - Recommended gap between profile and bath edge is between 10-15mm. 1X - Mark the holes on the wall. 15mm 10- 4 - Drill the holes(Ø6mm) according to the marks and 4. N4FS06 insert the wall plugs(N4FS06) into the holes. 4X N4FS06 N4FS05 N4FS01 - Fasten wall profile(N4FS01) on the wall with screw 5. (N4FS05). ST4X40 4X 1X N4FS01 N4FS05 5 - Insert screen panel into wall profile. - There is 0.39"(10mm )adjustment between panel and wall profile for any out of true walls. 6. - Adjust the screen panel in correct position and make sure glass panel fits parallel to the bath edge, but does not sit down directly on bathtub edge. 0.39"(10mm) - From inside drill through the vertical profile and into N4FS04 N4FS09 N4FS10 wall profile where shown, using a 3.2 mm drill. 7. 3.2 - Fix the wall profile(N4FS01) and frame together with ST4X10 screw(N4FS04), washer (N4FS09) and screw 4X 4X 4X cap(N4FS10). φ3.2 N4FS02 N4FS09 N4FS10 N4FS04 6 - Put top cap N4FS07 on the top of wall profile. 8. N4FS07 1X N4FS07 - Apply silicone sealant to the outside of the enclosure. Please note: Do not apply silicone sealant to the inside 9. SILICONE of the enclosure. Sealant drying times may vary in cold damp conditions and will be extended where thicker beads of sealant are applied. Allow sealant to dry completely before exposing to water. 7 - Before the first use, apply the silicone grease on each N4FS11 joint part as below drawing to make the opening and SILICONE closing smoothly. 10. GREASE 1X Cleaning and Maintenance: We have taken great care to ensure that this product Please do not use abrasive or strong cleaning reaches you in perfect condition. However should any solutions on the shower enclosure, such as parts be damaged or missing please contact your point alcohol, petroleum liquids or any other chemical of purchase. This does not affect your statutory rights. cleaner. In addition if you require replacement parts your point Should there be any dirty stains on the shower of purchase will be happy to assist. enclosure, please clean it with a soft lint free cloth and warm soapy water. Please rinse it with clean water afterwards. V18G27 8.