Nissan 2006-2007 99-7606
Total Page:16
File Type:pdf, Size:1020Kb
INSTALLATION INSTRUCTIONS FOR PART 99-7606 APPLICATIONS Nissan 2006-2007 99-7606 KIT FEATURES • DIN radio provision with pocket • ISO radio unit provision with pocket • Double DIN radio provision • Stacked ISO head unit provision KIT COMPONENTS • A) Radio housing • B) ISO brackets • C) ISO trim plate • D) Double DIN brackets • E) Double DIN trim plate • F) Pocket • G) (6) Panel clips • H ) 2 Sided tape (not shown) A B C D E F G WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: • 70-7550 - Nissan and Infiniti vehicles 1995-up • 70-7551 - Select Nissan and Infiniti vehicles Antenna Adapter: • Not required TOOLS REQUIRED • Torx T-10 driver • Phillips screwdriver • Small flat blade screwdriver or Panel removal tool REV. 7/2/2012 REV. INST99-7606 METRA. THE WORLD’S BEST KITS.™ 1-800-221-0932 metraonline.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION 99-7606 Table of Contents Dash Disassembly – Nissan Titan 2006-2007 (with dual zone climate controls) .................................................3-4 – Nissan Pathfinder Armada 2006-2007 ...........................................................................3-4 Pre-Kit Assembly ...............................................................................................................5 Kit Assembly – DIN radio provision with pocket ......................................................................................6 – ISO radio provision with pocket ......................................................................................7 – Double DIN radio provision ..............................................................................................8 – Stacked ISO head unit provision ......................................................................................9 CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition. Note: Refer to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Dash Disassembly 99-7606 Nissan Titan/Pathfinder Armada 2006-2007 1. Unclip and remove entire panel including radio and climate controls. (Figure A) 2. Remove (4) Phillips screws to remove radio from sub-dash. (Figure B) 3. Unsnap and remove the outer trim rings around A/C control knobs. (Figure C) Note: The small round airbag sticker also needs to be removed from the factory panel and placed onto the 99-7606 radio housing panel (a round (Figure A) piece of double-sided tape is provided in case the factory sticker is not strong enough). (Figure C) 4. Remove (4) T-10 Torx screws from the A/C controls to remove from the factory radio trim panel. Continued on next page (Figure B) OFF (Figure C) 3 Dash Disassembly 99-7606 Nissan Titan/Pathfinder Armada 2006-2007 5. Unclip and remove the hazard light switch assembly. (Figure D) INSIDE VIEW - RADIO TRIM PANEL BACK 6. Remove (2) T10 Torx screws from the passenger air bag off light assembly and remove. (Figure D) Note: The small round sticker also needs to be removed from the factory panel and placed onto the 1 3T-10 TORX SCREWS 99-7606 radio housing. 7. Attach the (6) panel clips in the same A/C CONTROL PANEL position as the factory radio trim panel. T-10 TORX SCREWS 4 PASSENGER AIR BAG LIGHT Note: If clips are not provided then 2 1 2 please remove the factory clips and CLIP T-10 TORX T-10 TORX re-use them. HAZARD SWITCH SCREW SCREW Continued on next page (Figure D) 4 Pre-Kit Assembly 99-7606 Nissan Titan/Pathfinder Armada 2006-2007 1. Attach the A/C control to the 99-7606 radio housing using the factory hardware removed in the dash disassembly. (Figure A) 2. Snap the outer trim rings onto the A/C 0 control knobs. (Figure B) 1 2 3 4 A/C 0 R 1 2 R 3 3. Attach the passenger air bag off light MAX A/C 4 assembly to the 99-7606 radio housing R using the factory hardware removed in the dash disassembly. Also, apply to air bag button the small round airbag (Figure B) sticker previously removed in Step 4 dash disassembly. (Figure C) 4. Snap the hazard light switch into the 99-7606 radio housing. (Figure D) 5. Attach the (6) panel clips to the 99-7606 radio housing panel using the 0 1 2 3 factory radio panel as a reference for 4 A/C OFF 0 R 1 2 R MAX 3 clip positioning. A/C 4 Continue to kit assembly R (Figure C) 0 0 1 1 2 2 3 3 4 4 A/C A/C OFF 0 0 R R 1 1 2 2 R R MAX 3 A/C MAX 3 A/C 4 4 R R (Figure A) (Figure D) 5 Kit Assembly 99-7606 DIN radio provision with pocket 1. Slide the DIN cage into the radio housing and secure by bending the metal locking tabs down. (Figure A) 2. Slide the aftermarket radio unit into the cage and secure. (Figure B) 3. Snap the pocket into the radio housing. (Figure C) 4. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative (Figure A) battery terminal and test the unit for proper operation. 5. Reassemble dash in reverse order of disassembly. (Figure B) (Figure C) 6 Kit Assembly 99-7606 ISO radio provision with pocket 1. Mount the ISO brackets to the radio with the screws supplied with the radio. (Figure A) 2. Slide the radio into the radio opening until the side clips engage. (Figure B) 3. Snap the trim plate into the radio housing. (Figure C) 4. Snap the pocket into the radio housing. (Figure D) 5. Locate the factory wiring harness in (Figure B) the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 6. Reassemble dash in reverse order of disassembly. (Figure C) (Figure A) (Figure D) 7 Kit Assembly 99-7606 Double DIN radio unit provision 1. Cut and remove center divider from radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3. Slide the Double DIN radio into the Double DIN bracket/radio housing assembly and secure the radio to the kit using the screws supplied with the head unit. (Figure C) 4. Snap the Double DIN trim plate onto the (Figure A) housing/radio assembly. (Figure C) 5. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 6. Reassemble dash in reverse order of disassembly. (Figure B) (Figure C) 8 Kit Assembly 99-7606 Stacked ISO head unit provision 1. Cut and remove center divider from radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3. Slide the Double DIN radio into the Double DIN bracket/radio housing assembly and secure the radio to the kit using the screws supplied with the head unit. (Figure C) 4. Snap the Double DIN trim plate onto the (Figure A) housing/radio assembly. (Figure C) 5. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 6. Reassemble dash in reverse order of disassembly. (Figure B) (Figure C) 9 Notes Notes INSTALLATION INSTRUCTIONS FOR PART 99-7606 REV. 7/2/2012 REV. INST99-7606 METRA. THE WORLD’S BEST KITS.™ 1-800-221-0932 metraonline.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7606 APLICACIONES Nissan 2006-2007 99-7606 CARACTERÍSTICAS DEL KIT • Provisión de radio DIN con bolsillo • Provisión de radio ISO con bolsillo • Provisión de unidad central doble DIN • Provisión de unidad central ISO vertical COMPONENTES DEL KIT • A) Alojamiento del radio • B) Soportes ISO • C) Placa de moldura ISO • D) Soportes doble DIN • E) Placa de moldura doble DIN • F) Bolsillo • G) (6) Ganchos del panel • H ) 2-cara cinta (no mostrado) A B C D E F CABLEADO Y CONEXIONES DE ANTENA (se venden por separado) Arnés de cableado: • 70-7550 - Vehículos Nissan y Infiniti 1995 y mas G • 70-7551 - Seleccione los vehículos Nissan y Infiniti Adaptador de antena: • No se requiere HERRAMIENTAS REQUERIDAS • Destornillador Torx T-10 • Destornillador Phillips • Destornillador de hoja plana pequeño o Herramienta para quitar paneles REV. 7/10/2012 REV. INST99-7606 METRA. THE WORLD’S BEST KITS.™ 1-800-221-0932 metraonline.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION 99-7606 Indice Desmontaje del tablero – Nissan Titan 2006-2007 (con controles de clima de zona dual) ..........................................3-4 – Nissan Pathfinder Armada 2006-2007 ...........................................................................3-4 Pre-Ensamble del kit .........................................................................................................5 Ensamble del kit – Provisión de radio DIN con bolsillo ....................................................................................6 – Provisión de radio ISO con bolsillo ....................................................................................7 – Provisión de unidad central doble DIN ...............................................................................8 – Provisión de unidad central ISO vertical ............................................................................9