RS Part No. 696-1184

Instruction Manual ColorColor BBoxox CCameraamera SCC 541H RS PART No.:696-1184

DATA SHEET DIGITAL BOX SCC541H

SPECIFICATION ECC541H (NTSC) ECC541H (PAL)

Image Device 1/3" Color SONY Super HAD CCD Picture Elements 768(H)×494(V) 752(H)×582(V) Scanning System 520 Lines, 2:1 Interlace 550 Lines, 2:1 Interlace Sync System Internal Synchronization Horizontal Resolution 550 TV Line Video Output 1Vp-p 75Ω S/N Ratio More Than 50dB (AGC Off) Electronic Auto/Manual ( Level Adjustable ) OSD Built-In ( External 5 buttons ) True Day & Night On/Off BLC On/Off ( Level Adjustable ) BLC Area On/Off ( Zone Selectable ) Characteristic Internal Synchronization: selectable ( 0.05~1.00) AGC On/Off ( Level Adjustable ) Sharpness On/Off ( Level Adjustable ) Mirror On/Off Privacy On/Off ( Zone Selectable ) Motion On/Off Camera ID On/Off Option Manual / DC Iris Lens / Video Iris Lens Smear Effect 0.005% Minimum Illumination 0.1Lux (F:1.2) Power Consumption DC 9V ~ 15V, 100mA Operation Temperature 10℃~＋50℃, RH95% Max (14˚F~122˚F) Storage Temperature 20℃~＋60℃, RH95% Max Weight Approx 235 g Housing ALUMINUM Dimension(mm) 1150 x 590 x 590

RS PART No.:696-1184

OWNER’S MANUAL HOW TO USE DIGITAL COLOR BOX CAMERA

***NOTE: CS MOUNT LENS & BRACKET ARE NOT Production composition & Parts Names PROVIDED. PLEASE PUT THE DESIRED LENS ON THIS CAMERA.

-Picture: How to connect CS mount Lens ** Before installing or adjusting please read installation guide that accompany with this product. Failure to follow warning notices and instructions may result in property damage. Improper installation and/or operation will void the warranty. Before Using or Installing Please do not make any attempt to disassemble the camera. To avoid any electrical shock, Please do not remove camera cover & screw. Installation & connection Please consult with Installation specialist since there is no user 1)Prepare the desired Lens and fix it. Also connect lens cable in. execution. 2)If possible, using bracket or camera housing for this camera. Please do not use strong chemicals or detergent. And then install this camera at proper position. Use dry towel to wipe off the camera, to clean off the stain use weak 3)Connect power cable in.as above picture. Cleaning detergent. 4)Connect Video cable out as above picture. Before operation please check the temperature, humidity, and level of 5)Power on, the power Lamp turns on. the power. 6)To use OSD keys, you can control image condition as you want. Please operate camera between temperature levels of -10 ~ 50 . ℃ ℃ - Please refer following explanation. Please do not disclose the camera, if there is lot of smoke or gas. Please do not disclose the camera under direct sunlight. Trouble Shooting Do not aim camera directly at bright object. If you are not able to view anything from the screen. By doing so, this action will cause blooming or smear. Check power, video, strength of signal. Please handle camera with care. Check monitor input/output. Do not put camera near fire, as this may cause fire. Check camera connection number with monitor. Please do not hit, or shake the camera. For Fuzzy Screen This could cause camera to malfunction. Check for dust or dirt. If so wipe them Improper care or use of the camera could damage the camera. off with dry towel or brush. Please do not make children handle or operate camera. It may Check cover to see if it’s clean. If so wipe them off with dry towel or cause children’s accidents or camera’s malfunction. brush. Check for direct sunlight towards camera. . How to Use &Installations & Warnings Check if protection film from camera cover is removed Use of DC12V. ( Please use Adapter 1A for DC12V). For Dark Screen Please use dry towel to clean camera instead of the abrasive. Check for Monitor Brightness. (This could bring low quality screen view of camera) Unbalanced Black & White on the Monitor. Please do not misplace the camera. And prevent any malfunction. -Check Monitor Please do not use camera in humid or wet area. -Adjust the position or angle of lens when screen is bright Do not disclose camera to direct sunlight If problem still remains please contact our Technical Do not expose camera to massive electric wave. Support Department. Do not install camera location with lot of vibration. Do not install product near very high temperature or very low temperature area. (Please refer to our operation manual on operation temperature & storage temperature) Do not attempt to open dome cover after installation and image adjustment

RS PART No.:696-1184

OWNER’S MANUAL-OSD function DIGITAL COLOR BOX CAMERA SCC541H

General Characteristic on SCI541 camera << Overview >> ·SCI541H offer exterior-easy setting of camera functions what users want, as it no requires extra Picture 2. MCU to command the DSP of the CCD module.

1.<< Direction >> · With Video Signal into the monitor, KEY^2_S/W brings up the 2-3:ADJUST menu, picture 0. ·Select "ADJUST" and press KEY^3_S/W to activate the list like · Use KEY^1_S/W to select the each item downward. Picture 4. · Selected item High-Lighted in darker. Use KEY^1_S/W to select a list to change the setting as user wants. · Use KEY^3_S/W to make changes on the selected item. Press KEY^2_S/W and ues KEY^1_S/W & KEY^3_S/W to · To make the changes permanent, must "Exit" the "SET UP" menu. increase & decrease the volume. · Once changes made, it stays regardless of power ON/OFF. Again press KEY^2_S/W to move to the next item and select "RETURN." Press KEY^2_S/W to go back to the "Set Up Menu." Picture 0. Basic Menu

Picture 3. Adjustment menu

2. Functions on the menu and details 2-1:LENS · Select "LENS," press KEY^3_S/W to move to "MANUAL" - 2-4:DAY NIGHT "VIDEO " - "DC" in order. · Select "DAYNIGHT" and press KEY^3_S/W to move "AUTO" - " On the "DC", press KEY^2_S/W brings up the Picture 2KEY^1_S/W B/W " - "COLOR" in order. & KEY^3_S/W use to increase & decrease " Brightness" of the DC Use KEY^1_S/W to select a list to change the setting as user IRIS . wants. Press KEY^2_S/W to go back to the "Set Up Menu." Press KEY^2_S/W to select the menu and ues KEY^1_S/W & KEY^3_S/W to increase & decrease the volume. Again press KEY^2_S/W to move to the next item and select Picture 1. LENS : "RETURN. MANUAL_DC IRIS Press KEY^2_S/W to go back to the "Set Up Menu."

2-2:SHUTTER

· Select "SHUTTER," press KEY^3_S/W to move to

"AUTO" - " FLK " - "FIXED" - " MENUAL" in order. Picture 4. DAY NIGHT On the "AUTO", press KEY^2_S/W brings up the Picture 3 OPTION KEY^1_S/W & KEY^3_S/W use to increase & decrease shutter speed. Press KEY^2_S/W to go back to the "Set Up Menu."

RS PART No.:696-1184

OWNER’S MANUAL-OSD function DIGITAL COLOR BOX CAMERA SCC541H

2-5:WHITE BAL. · Select "WHITE BALANCE" and press KEY^3_S/W to move Picture 6-3. SETTING BLC "ATW" - "AWB" - "FIXED" - "MANUAL" in order. RATIO Press KEY^2_S/W to activate "AWB MANUL" like Picture 6. Use KEY^1_S/W to select a list to change the setting as user wants. Ues KEY^1_S/W & KEY^3_S/W to increase & decrease the volume. 2-7:MIRROR Again press KEY^2_S/W to move to the next item and select · After select the "MIRROR," set MIRROR ON/OFF by pressing "RETURN." KEY^3_S/W. Press KEY^2_S/W to go back to the "Set Up Menu." 2-8:AGC · Select "AGC" and press KEY^3_S/W to set "AGC ON/OFF."

Select "AGC ON" brings up the menu like the Picture 8. Press KEY^2_S/W and use KEY^1_S/W & KEY^3_S/W to Picture 5. WHITE BALANCE increase & decrease the volume. Press KEY^2_S/W to go back to the "Set Up Menu."

Picture 8. AGC Control 2-6:BLC · Select "BLC" and press KEY^3_S/W to set "BLC ON/OFF." Press KEY^2_S/W to activate "BLC ON" like Picture 6-1. Use KEY^1_S/W to selcet a list to change the setting as user 2-9:GAMMA wants. Select "GAMMA" and press KEY^3_S/W to volume "0.05" - Ues KEY^1_S/W & KEY^3_S/W to increase & decrease the · volume. "1.0 " in order. Again press KEY^2_S/W to move to the next item and select 2-10:RESET "RETURN." · Select "RESET" and press KEY^2_S/W to display the Picture 10. · Select "YES" and press KEY^2_S/W will reset to the default setting. Picture 6-1. BLC ON/OFF Picture 10. Reset

2-6-1.BLC AREA · Select "BLC AREA" and press KEY^1_S/W to set BLC area. After setting the area, press KEY^2_S/W long brings up the Picture 6-2. 2-11:EXIT Use KEY^1_S/W to select a list and press KEY^2_S/W to change . Select "EXIT" with KEY^1_S/W, press KEY^2_S/W to turn off the setting as user wants. OSD. Select "EXIT" using KEY^1_S/W ( Picture 6-3) and press KEY^2_S/W to go back to the "BLC SETUP." 3. Other functions

Picture 6-2. SETTING BLC Picture 11. Others RATIO