------_------.-

IBM 5110 System Maintenance Analysis Procedures o o.

W· o

o

Third Edition (January 1979)

This a major revision of, and obsoletes, SY31-0553-1. Because the changes and additions are extensive, this publication should be reviewed in its entirety.

Changes are periodically made to the information herein; changes will be reported in technical newsletters or in new editions of this publication. o Use this publication only as an aid in servicing the IBM 5110 System.

Publications are not stocked at the address below. Requests for copies of IBM publications and for technical information about the system should be made to your IBM representative or to the branch office serving your locality. This publication could contain technical inaccuracies or typographical errors. Use o the Reader's Comment Form at the back of this publication to make comments about this publication. If the form has been removed, address your comments to IBM Corporation, Publications, Department 245, Rochester, Minnesota 55901. IBM may use and distribute any of the information you supply in any way it believes appropriate without incurring any obligation whatever. You may, of course, continue to use the information you supply. o

© Copyright International Business Machines Corporation 1978, 1979 I Contents ( I

Logic Card Part Numbers ...... 050-1 Logic Card Jumpers...... 050-5 I USING THE IBM 5110 COMPUTER MAPs. 0100-1 MAPs ...... 0100-1 ( MAP Organization 0100-2 Using the MAPs. 0100-3 II MAP Examples .. 0100-4 Start MAP ..... 0200-1 ,. Cable Checkout MAP. . 0210-1 (-- Tape Read MAP .... 0300-1 Di~.kette Read MAP .. 0310-1 I Bring Up MAP ..... 0400-1 Process Check MAP .. 0420-1 Display MAP ...... 0500-1 TV Monitor MAP .. 0510-1 I Keyboard MAP . . . . 0600-1 Power MAP ...... 0700-1 5103 Printer MAP ... 0810-1 Communications, Serial I/O, and Parallel I/O . 0830-1 Transmit/Receive Level Checkout MAP . 0831-1 I Local CBS Coupler (Auto Answer) MAP for 38LS Integrated Modem ...... 0832-1 Manual Call to a Manual Answer Station Using a CDT Type Coupler 0833-1 I Digital Network Remote Wrap Test Procedure ...... 0834-1 BSC Network and BSCA (:-/ Intermittent Problem MAP 0835-1 Automatic Answer MAP for 38LS I with World Trade Line Box .... 0836-1 Manual Call MAP for World Trade 38LS ...... 0837-1 Manual Answer MAP for 38LS with I World Trade Line Box ...... 0838-1 Auxiliary Tape MAP ...... 0850-1 5114 Diskette Unit Entry MAP .. 0880-1 Machine Checkout MAP ...... 0900-1 II II ('~-' II

I-; 1..- iii I "\

This page intentionally left blank.

iv LOGIC CARD PART NUMBERS I Card Name Location Model Part Number (,e, ~" I/O cable driver A2 4360292

Async comm-serial I/O D2 1607138

APL ROS E4 AXX or CXX 4360442 ('" ~h, 4834732

., ..-/ Common and language F2 A1X2 4360434 ROS 4834796 4834764 1

B1X2 4834714 (:~/ 4834722 4834796 4834764 1

C1X 2 4834712 4834724 4834796 4834764 1

A2X 3 4834716 4834726 4834754 4834766 1 (~1' ,/ B2X 3 4834718 4834728 4834798 4834768 1

C2X 3 4834720 4834730 4834800 48347701

Display G2 4360476 4360450 (Katakana 4834708 ("'h feature only) -L •. ./

Base I/O H2 X1X 4360496 4834746

(~~ X2X 4834700 4834794 ,./'

Processor J2 1607136

IThe Katakana feature requires one of these cards to be included. Parallel I/O K2 4360430 2The cards in model C1 X may be substituted for the cards in models A 1 X and B1 X. C~/ Feature ROS K4 4834964 3The cards in model C2X may be substituted for the (diskette sort) 4834972 cards in models A2X and B2X. MAP 050·1 Card Name Location Model Part Number

Executable ROS L2 A1X or C1X6 4834734 ,/ ,Jr 4360478 :.. ~ 4834784 1

B1X6 4834736 4360480 48347861

,~, A2X or C2X7 4834738 4360482 4360478 ,.. 48347841

B2X7 4834740 ,Iii 4360484 48347881

Read/write M2-N4 8238223

Print adapter 5103 16071422 1607154 1607152 (Katakana 4834706 feature only)

Tape adapter 5106 16071342 1607144 1607146

Tape control 5106 or 8527645 internal tape

Diskette adapter 5114 4834710 4834960 48349783 48349623

Diskette control 5114 8528195 4178068 4178065

VFO 5114 16072174

BSCA 2 A4 48347922 4834780

BSCA 1 B2 16071765

IThe Katakana feature requires one of these cards to be installed. 200 not replace with the same part number. 3 The VFO card is incorporated in this card. 4Not used with diskette adapter card 4834710 or 4834960. 5 The microprocessor module on this card is part 5615702. j'." 6The cards in models A 1 X or C2X may be substituted for the cards in the 5110 model B1 X. 7The cards in models A2X or C2X may be substituted for the cards in the MAP 050-2 5110 model B2X. I Communication Location Model Part Number (:' Communication C2 facility

EJA Used with 5864363 external modems 5864660

DDSA Used with 8527032 (~'".~ digital network .. 38LS U.S. switched network 1756001 with auto answer 8564508

38LS U.S. non-switched 1756003 network with SNBU 8564509 ( ... '" 38LS U.S. non-switched 1756005 network without SNBU 8454510

38LS World Trade non- 1756011 switched network 8564481

38LS World Trade 1756007 switched network 8564479

c

c c

MAP 050-3 "

This page intentionally left blank.

MAP 050-4 LOGIC CARD JUMPERS Display Card Display Card Printer Adapter Card! PIN 4360476 PIN 4360450 (

\ \ \ \ \ \ \ I \ \ \ \ \ \ \ ~ \ \ \ \ \ , \ , I ...... ~-~ .( Country Jumper Positions! Jumper Positions2 Jumper Positions2 1-- - Austria/Germany .-§WiB • -._ . .- .- -III .-. . - -. -; - - Belgium - . -...- .-. .- I-II . - - . . .- II- - Brazil -.lilliE. -._. .- - -II -. -. - -I - Denmark/Norway . - .- .-.- . _..- -. -.. . -.- II-I EBCDIC (U.S.) 1 . IIII .- ... -. - - . . ~- - . --- c Finland/Sweden . a-I- .--- . _. .- -_. -I- I France . -II- --• MmII. .... -- ...-- I - -I _. .-_. -III French/Canada -.• iU!lllII .- 1-- - .- -._. .- I-II International .....- . - ..- . .1 -- . - .-• IIIBl III- Italy -. . - _. - .• -. -. .. --- . -I Japan 1 . -- . ... .- III- .- ... _.. - .- I- -I Portugal .- -. .- . I I - -. .- . - - . I Spain ... . I - - . . - . . - I -I - .- ... -_. .- II-I c Spanish Speaking ... -. . - .-. .-- .- -._. -. ---II-I - United Kingdom . - ... II- - .- .- .- .-• .- .- - - -- Unassigned -. .- _. • • - IIII Iprinter adapter card used with Katakana feature should have either EBCDIC- (U.S.) jumpers- or none at all. 2There is no display jumpering for the Katakana feature. ' MAP 050-5 Executable ROS Card (L2) Jumper Position for IIII 5110-X1 X Diskette II: : Adapter Jumper Position Card for All Machines Jumper Position for III: 5110-X2X ...... I;:: ......

I I I d:!3

Auxiliary Tape Unit Adapter Card ,, '-.e._ e ------, ~ DDDDDD Feature ROS Card (K4)

Jumper Position for 5100

Jumper Position for 5110

Jumper on for All Machines

Processor Card(J2)

Jumper Position for 5100

Jumper Position for 5110

Jumper Position for 5100 ~ ~ Jumper Position for 5110

MAP 050-6 I

USING THE IBM 5110 SYSTEM MAPS

MAPs

The MAPs guide you through the service call using step-by­ step procedures that require you to follow trace lines when responding to questions or when leaving or entering a page. The MAPs use a logical approach for isolating the possible causes of machine problems and point you to that part of the 5110 that requires adjustment or replacement.

Two types of MAPs are used in the 5110 maintenance library. First, there are the hard-copy (printed) MAPs within the MLM binder. These MAPs are contained in a separate removable binder. The second type of MAP is the MOl (MAP diagnostic integration). These MAPs are located on the diagnostic tape/diskette and are shown on the display screen. The system automatically pages through the MAPs when you respond to the questions on the display.

c

MAP 0100-1 MAP ORGANIZATION

START

Start MAP 200

Record the Error Code Displayed

Indicator Lights-Use MAP 200

Other Reported Fail u res ------f..------1~O-~L-______~

NoSymptoms------+------,

Begin each call with Start MAP 200. This MAP ensures that the system is operating sufficiently to use other MAPs or MDls.

Start MAP 200 asks you to record the status , error logs, and history logs because this information is lost on power down or RESTART. The Start MAP either fixes or directs you to a MAP that tells you how to fix any of the following problems: I ndi cator lights Bring up failures Process checks Display failures For other failures, the Start MAP directs you to the correct MAP through an error code. If you are certain the failure is not covered in the Start MAP, you can go directly to the other MAPs indicated by the ® in the chart.

All MDls have a MAP as an entry. For example, MAP 810-5103 is an entry for MOl 800 through 805. These MAPs provide the setup instructions for running the MDls.

The MDls are a combination of MAPs and diagnostics. The MD Is call in and run the appropriate diagnostics and answer most of the MAP questions automatically.

The procedures for diagnosing intermittent failures contain a more detailed description of what part of the system each MOl checks. USING THE MAPS (.~.\ When using the MAPs, you must: I READ CAREFULLY. The MAPs can help you find the problem only if you follow instructions and answer questions accurately.

FOLLOW THE SEQUENCE. Proceed step-by-step at all times. At times, the MAP instructions might seem irrele­ -vant. However, they can be important in determining the correct error indications.

FOLLOW INSTRUCTIONS. Instructions must be carried out exactly in the order given. Questions are based on instructions immediately preceding the questions. Do not change the conditions established by the instructions before answering the questions. Do not press the RESTART switch until you are told to do so in the MAPs.

When you are asked to probe a line in the MAPs, the line name and its active level are given. For example:

- Probe H2-G06 (- machine check).

The - (minus) in front of machine check indicates that this line is active at a down level.

·" C/

CI

MAP 0100-3 MAP EXAMPLE __----- MAP name and number

points-show all entry and exit points to PROCESS CHECK MAP 0420 ------~En:t~ry::a~nd~exit and from this MAP. PAGE 1 OF 75

ENTRY POINTS

FROM ENTER THIS MAP EXIT THIS MAP TO MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT

0200 A 001 5 044 0400 A 0300 A 001 18 218 0400 A 0600 A 001 75 828 0500 A 0810 A 001 0830 A 001 0850 A 001 0900 A 001 830C A 001

001 ------Step number (Entry Point A) ______Entry point-indicates a possible starting point in this MAP. It is usually referenced from a step within a Is the PROCESS CH ECK light on '7 MAP. Y N------Y=yes, N=no 002 Can you create the PROCESS CHECK? Y N 'l .,:,/

003 The MAPs depend on having the PROCESS CHECK on the machine or being able to create the PROCESS CHECK. Gather and record all available information pertaining to the PROCESS CHECK. Advise the customer that if the PROCESS CHECK appears again, to leave the machine in the failing condition until you arrive.

004 Is the PROCESS CHECK intermittent? Y N

Off-page reference-identifies the page and trace on which this MAP leg continues. The 2 indicates that this leg continues on page 2. The C indicates that th is leg continues at trace C.

222 ABC

MAP 0100-4 MAP EXAMPLE (continued) ABC PROCESS CHECK MAP ('\, 1 1 1-

PAGE 2 OF 75 - On-page reference-indicates the trace and page from I which this MAP leg came. The 1 indicates that this 005 leg came from page 1. The C indicates that this leg Create the PROCESS CHECK. came from trace C. ( .""'\ • 0' Did the PROCESS CHECK come on as a result of pressing RESTART or powering on the 5110? Y N

006 We will assume that the PROCESS CHECK comes on as a result of running a job. Go to Step 010, ------Internal exit point-indicates the page, step, and entry Entry Point H. point to go to within this MAP.

007 We will use the RESTART condition to create the PROCESS CHECK. Go To Map 0400, Entry Point A. ------External exit point-indicates the MAP and entry point to go to. 008 Create the PROCESS CHECK ------Instruction-establishes conditions for answering the Go to the INTERMITTENT FAI LURE CHART next question. c 5110 in the SERVICE AIDS.

009 Is the PROCESS CHECK intermittent7------0uestion-answer either yes or no. Continue from Y N your answer to the next question or instruction.

010 (Entry Point H)

Bad RESTART switch. ------Action-possible fixes for the failure. Replace, repair, Check/replace Z3 (display and control panel) or adjust in the order given. (Check/replace means to cable (see MAP 0210 and MIM 210, 241). check first, then replace if defective.) c" Is the display blank or dark 7 Y N

011 Reference number-refers to a location graphic, Are there ~ny devices attached to th~ maintenance procedure, chart, or other pertinent 5110 I/O mterface port? (see MIM information in the maintenance section. 271) Y N

_ On-page reference-indicates the trace on this page CI 7 7 1 from which this leg of the MAP continues. 558 o E F G- 1-10 MAP 0100-5 MAP 0100·6

This page intentionally left blank.

MAP 0100·6 ('.'" START MAP 0200 MAP 0200-1

PAGE 1 OF 5

ENTRY POINTS EXIT POINTS I ',,", ('" FROM ENTER THIS MAP EXIT THIS MAP TO . _/ MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT .. 0300 A 2 001 4 020 0300 B (' 0900 A 2 001 4 020 0310 A _/ 3 014 0400 A 3 018 0400 D 5 030 0420 A 4 020 0420 A 4 021 0420 A 4 026 0420 A 5 027 0500 A 3 012 0500 A 4 025 0500 A 3 015 0500 A 4 020 0500 A 4 024 0500 A 4 020 0510 A C 4 020 0600 A 4 020 0810 A 4 020 0830 A MAP 0200, ENTRY POINT A IS ON PAGE 2 4 020 0850 A 4 020 0880 A 4 020 0900 A 4 020 0900 C 4 020 0900 D 4 020 0900 F

c c © Copyright I BM Corp. 1979 01JAN79 EC 836600 PEC 835541

MAP 0200-1 START MAP o MAP 0200-2

PAGE 2 OF 5

001 004 (Entry Point A) To test the indicator lights:

When the MAP leads to a bad card, measure the -Press and hold the RESTART switch. , jI' .. voltages at the card location before replacing the card (see MIM 274, DC VOLTAGE Are both the PROCESS CHECK light and the DISTRIBUTION). If any voltages are out of I N PROCESS light on? tolerance Go To Map 0700, Entry Point A. V N Any reference numbers in the MAPs, such as (see MIM 241), will be for the 5110 MIM, unless 005 stated otherwise. Bad L2 (exec ROS) card (see MAP 050 for jumpering). - Record customer supplied information including Bad PROCESS CHECK light. error codes, if any. Bad IN PROCESS light. - Record the status bytes to aid in diagnosing Bad RESTART switch. intermittent I/O problems (see STATUS BYTES Check/ replace Z3 (display and control panel) and DISPLAY REGISTERS in the Diagnostic cable (see MAP 0210 and MIM 248,249). Aids section of the MIM). -Switch the L32-64-R32 switch to 64. 006 -Press the bottom of the REVERSE DISPLAY -Release the RESTART switch. Wait 25 switch. seconds. -Switch the DISPLAY REGISTERS switch to NORMAL. Is the PROCESS CHECK light on1 -Check that the RUN switch (under the covers) is V N set to run, if the covers are off (see MIM 201). 007 Is the PROCESS CHECK light on 1 -Adjust the BRIGHTNESS control so that if Y N there are any characters on the display they are well defined. 002 -Power on the 5110 or press RESTART. The 5110 display is grossly distorted if it has a black rather than a white background, or is Does the I N PROCESS light stay on? greatly reduced in size. Y N .. Is the 5110 display grossly distorted? 003 V N

Is the 5110 display dark for all positions 008 of the BRIGHTNESS control? Is the 5110 display rolling? Y N V N

01JAN79

EC 836600 PEC 835541 555 444 3 ABC D E F G H MAP 0200-2 H START MAP K L MAP 0200-3 ("'" 2 PAGE 3 OF 5

009 013 I Does the 5110 display contain wide -Switch the RUN switch under the covers to

'~'" / horizontal bars similar to a TV set with the RUN. ( horizontal hold out of adjustment? -ObseNe the IN PROCESS light. . " Y N -Hold down the CMD key and press the 4 key on the Alphameric Keyboard. 010 - Release the keys. No more than 25 seconds after RESTART is -Press EXECUTE. pressed, the following events should occur: 1. ABCDEFGH appears on the top line of the Does the I N PROCESS light turn on or 5110 display. flash? 2. ABCDEFGHJKLMNP appears on the top Y N line. 3. The top line is cleared and either LOADO 014 or CLEAR WS appears once on one and -Switch the DISPLAY REGISTERS switch only one iine of the 5110 display. to NORMAL.

-Press RESTART. Go To Map 0400, Entry Point A.

Do all three events occur before 25 015 seconds, in sequence, after RESTART is Bringup is OK. pressed? Y N -Switch the DISPLAY REGISTERS switch to c' NORMAL. 011 - Press A TIN to reset the error condition. -Switch the RUN switch under the covers to NOT RUN (see MIM 201). Go To Map 0500, Entry Point A. -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. 016 (See DISPLAY REG ISTERS in the Does an error code appear on the display Diagnostic Aids section in the MIM). after RESTART is pressed? Y N Do all 1024 positions contain legible, well-formed characters, with no blank 017 spaces? Are the top 13 lines of the display entirely Y N blank (there are 16 lines total for the display)? 012 Y N -Switch the DISPLAY REGISTERS switch to NORMAL. 018 -Switch the RUN switch under the Go To Map 0400, Entry Point D. covers to RUN. c 019 Go To Map 0500, Entry Point A. Is the PROCESS CHECK light on? Y N

01JAN79

EC 836600 PEC 835541 4 444 J K L M N P MAP 0200-3 P START MAP E F G J M N MAP 0200-4 3 2 2 2 3 3 3

PAGE 4 OF 5

(Step 020 continued) 020 (Entry Point E) -ALARM Go To Map 0900, - Use the customer information recorded earlier Entry Point D. and the customer error code charts to determine the probable failure area. -5110 SWITCH CHECKOUT - Record the status bytes to aid in diagnosing Go To Map 0900, intermittent I/O problems (see STATUS BYTES Entry Point F. and DISPLAY REGISTERS in the Diagnostic Aids section of the MIM). -MACHINE CHECKOUT Go To Map 0900, Exit to the appropriate MAP : Entry Point A.

-INTERNAL TAPE UNIT -If the failing area can not be Go To Map 0300, Entry Point B. identified from the list above: Go To Map 0900, -5114 DRIVE 1 (only use this Map if the 5110 Entry Point C. does NOT have an internal tape drive) Go To Map 0310, Entry Point A. 021 Go To Map 0420, Entry Point A. -DISPLAY Go To Map 0500, Entry Point A. 022 Go to Step 020, -TV MONITOR Entry Point E. Go To Map 0510, Entry Point A. 023 -KEYBOARD Bad display assembly (see MIM 204). Go To Map 0600, Entry Point A. 024 -PRINTER The vertical frequency may be out of Go To Map 0810, Entry Point A. adjustment (see MIM 247 for adjustment).

-BSCA, ASYNC COMM-SERIAL I/O, PARALLEL ************* I/O * CAUTION * Go To Map 0830, Entry Point A. ************* High voltage is present. -AUXILIARY TAPE UNIT Go To Map 0850, Entry Point A. If this adjustment has no effect Go To Map 0500, Entry Point A. -DISKETTE DRIVE Go To Map 0880, Entry Point A. 025 Go To Map 0500, Entry Point A. -PROCESS CHECK Go To Map 0420, Entry Point A. 026 Go To Map 0420, Entry Point A.

(Step 020 continues) ,t' ""', 01JAN79 "",_ ,.lIto' EC 836600 PEe 835541

MAP 0200-4 ABC START MAP MAP 0200-5 222

PAGE 5 OF 5

027 I -Set the BRIGHTNESS control to the . (~ center of its range. Go To Map 0500, Entry Point A.

028 Bad G2 (display) card (see MAP 050 for jumpering). Bad L2 (exec ROS) card (see MAP 050 for jumpering). Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 248,249).

029 Is the IN PROCESS light on 7 Y N

030 Go To Map 0420, Entry Point A.

031 c Bad G2 (display) card (see MAP 050 for jumpering). Bad L2 (exec ROS) card (see MAP 050 for jumpering). Bad H2 (base I/O) card. Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 248,249). Bad RESTART switch .

• 'II C), c

01JAN79

EC 836600 PEC 835541

MAP 0200-5 ',,_ i l

This page intentionally left blank.

["',

\~ .. f

MAP 0200-6 CABLE CHECKOUT MAP 0210 MAP 0210-1

PAGE 1 OF 2

001 Use the following charts for cable problems: CABLE MIM REFERENCES I KEYBOARD 5110 206,255

DISPLAY and CONTROL PANEL Z3 5110 248,249

INTERNAL TAPE UNIT CABLE Z2 5110 230,231

5110 POWER Y1 5110 272

COMMUNICATIONS 5110 282

5106 CABLES 5110 283,280

5114 CABLES 5114 101,151,170

5103 CABLES 5103 304,384 5110 280

Are you checking an I/O interface cable? V N

002 '''','' ( - Remove cable at both ends if possible. / " -Set CE meter to the OHM X1 scale. - Place one meter lead on the suspected pin at one end of the cable. - Place the other meter lead on the suspected pin on the other end of the cable.

Is there any deflection on the meter? V N c· © Copyright IBM Corp. 1979 01JAN79 EC 836600 PEC 836541 222 ABC MAP 0210-1 ABC CABLE CHECKOUT MAP MAP 0210-2 111

PAGE 2 OF 2

(Step 009 continued) 003 The line in the cable is open. Is there any deflection on the meter? Repair / replace the cable Y N

004 010 Is there any resistance? The line in the cable is open. Y N Repair / replace the cable.

005 011 - Meter all the pins on one end of the cable Is there any resistance? to the suspected pin on the other end of Y N the cable. 012 Does more than one pin cause meter to - Meter all the pins on one end of the cable to deflect? the suspected pin on the other end of the Y N cable.

006 Does more than one pin cause the meter Cable checks out good. to deflect? Y N 007 The cable has a short circuit. 013 Cable checks out good. Repair / replace cable. 014 008 The cable has a short circuit. Their is resistance in the cable line. Repair / replace cable. Repair / replace the cable 015 009 Their is resistance in the cable line. (See 5114 MIM 280 ) If you have a 5114 and a 5103 attached to a Repair / replace the cable. 5110, the +5Vdc for the 5103 comes from the 5114 power supply. The only voltages that the 5114 uses from the 5110 are -12Vdc and +12Vdc.

-Power down. -Set the CE meter to the OHM x1 scale. - Place one meter lead on the suspected pin at one end of the cable. - Place the other meter lead on the suspected pin at the other end of the cable. (Step 009 continues)

01JAN79

EC 836600 PEC 835541

MAP 0210-2 TAPE READ MAP 0300 MAP 0300-1

(:" .. PAGE 1 OF 45

ENTRY POINTS EXIT POINTS

"'1 (' FROM ENTER THIS MAP EXIT THIS MAP TO if, .• MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT

... 0200 B 2 007 3 028 0200 A ( 0830 A 1 001 2 010 0420 A I 0860 A 1 001 2 014 0420 A 0861 A 1 001 45 529 0420 A 0900 A 1 001 45 527 0600 A 41 493 0700 A 37 427 0700 A 37 437 0700 A 38 443 0700 A 27 294 0700 A 12 121 0700 A 2 009 0900 A 2 013 0900 A 3 022 0900 A 9 092 0900 A C 44 525 0900 A

001 (Entry Point A)

Is the PROCESS CHECK light on? Y N

002 The tape read diagnostic program displays an error on the display if an error is found. An error is displayed in the following format near C~ the top of the display: ERROR XXX E 80 GOTO MAP 0300.

Is an error displayed? C Y N

© Copyright IBM Corp. 1979 01JAN79 4 EC 836600 PEC 835541 542 ABC MAP 0300-1 C TAPE READ MAP MAP 0300-2 1

PAGE 2 OF 45

(Step 007 continued) 003 The characters DSP MENU are displayed when If the DCP program load is OK, the characters the tape read diagnostic is done. DCP are displayed.

Are the characters DSP MENU displayed? Are the characters DCP displayed? Y N Y N

004 008 The instruction PRESS EXECUTE,R,or L Is the PROCESS CHECK light on? might be displayed on the display. Ignore Y N this instruction if it is displayed. 009 Are instructions (other than PRESS Go To Map 0900, Entry Point A. EXECUTE,R,or L) .or questions displayed? Y N 010 Go To Map 0420, Entry Point A. 005 Please observe again for: 011 Use the keys in the numeric key section. 1. PROCESS CHECK light on. 2. Error displayed. -Hold CMD and press * (BASIC multiply key). 3. Instructions or questions displayed. OR -Hold CMD and press x (APL multiply key). Do you have any of the above conditions? If the diagnostic mode load is ok, the characters Y N DIAG DCP are displayed (see MIM section 4, diagnostic aids). 006 Have you passed this step before? Are the characters DIAG DCP displayed? Y N Y N

007 . 012 (Entry Point B) Is the PROCESS CH ECK light on? Y N -If there is a cartridge in the tape drive, remove it. 013

-Press RESTART and wait 25 Go To Map 0900, Entry Point A. '\ _ .." seconds. 014 Use the keys in the numeric key Go To Map 0420, Entry Point A. section of the keyboard (see M I M 250).

-Hold CMD and press HOLD. -Hold CMD and press - (minus).

(Step 007 continues)

01JAN79

EC 836600 PEC 835541 333 3 3 o E F G H MAP 0300-2 G H TAPE READ MAP o E F MAP 0300-3 2 2 222

PAGE 3 OF 45

015 023 -Press C Go to Page 1, Step 001, Entry Point A. -Press 1 . (. -Press EXECUTE 024 An error instruction is displayed in the Do the words TAPE READ DIAGNOSTIC following format: appear on the top line of the display? Y N GOTO MAP 0300 ERROR XXX.

016 Is an error instruction displayed? Bad F2 (Common and language ROS) card. Y N •

017 025 You have loaded and are running the tape Do not press EXECUTE ,R ,or L unless read diagnostic (see M I M section 4, asked to. Follow the instructions displayed diagnostic aids). on this display. - Follow the instructions displayed to run the diagnostic. NOTE: After you follow the instructions on this display, another display might appear. Do the diagnostics run to completion? Ignore this next display. Y N Go to Page 1, Step 001, Entry Point A. 018 c' Is the PROCESS CHECK light on, or are 026 the characters DSP displayed? Go to Page 4, Step 034, Entry Point G. Y N 027 019 Are you diagnosing an internal tape drive Follow the instructions on the display. problem? If the display directs you to GO TO MAP Y N 0300, go to Entry Point A. 028 020 Go To Map 0200, Entry Point A. Suspect the tape control card along with the rest of the callouts. 029 - Follow the instructions displayed to run the tape c' Go to Page 1, Step 001, Entry Point A. write diagnostic. 021 Did the diagnostic run to completion? Go to Page 1, Step 001, Entry Point A. Y N

022 030 c Go To Map 0900, Entry Point A. Follow the instructions on the di~play.

01JAN79

EC 836600 PEC 835541 4 J MAP 0300-3 B J TAPE READ MAP Q MAP 0300-4 1 3

PAGE 4 OF 45

031 039 -Press RESTART. Wait 25 seconds. Error 0061 - Do the test at the end of the Select Magnet V N Service Check (see MIM 221). 040 Is the tape motion rhythmic1 Error 0071 V N V N

032 041 Do the Tape Select Magnet Service Check. Error 0081 (see MIM 221) V N

033 042 The tape unit checks out OK. Error 0091 V N 034 (Entry Point G) 043 Error 0101 These errors are valid only for the tape read V N diagnostic program. Scan through the errors until you find the error that is displayed on the display. Then take the Y leg to find the correct page number.

Error 0011 Y N

035 Error 0021 V N

036 Error 0031 V N

037 Error 0041 'I.. " Y N

038 Error 0051 V N

,(" ''\ 01JAN79 ~l... ~ 4 4 444 4 4 4 4 4 EC 836600 PEC 835541 5 444 3 3 3 3 3 2 5 K L M N P Q R STU V W MAP 0300-4 W TAPE READ MAP A MAP 0300-5 4 C

PAGE 5 OF 45

044 049 Error 011? Error 903? Y N Y N

045 050 Error 012? Error 906? Y N· Y N

046 051 Error 013? Error 907? Y N Y N •

047 052 Error 014? Error 909? Y N Y N

048 053 Error 901? Error 912? Y N Y N c

c

01JAN79 4 4 4 4 443 44422 2 2 0 0 9 6 EC 836600 PEC 835541 2 2 2 A A A A A A A A A X Y Z ABC o E F G H J MAP 0300-5 A TAPE READ MAP A MAP 0300-6 J Q 5

PAGE 6 OF 45

054 059 Error 9157 Error 9307 Y N Y N

055 060 Error 9187 Error 9337 Y N Y N

056 061 Error 9217 Error 936? Y N Y N

057 062 Error 9247 Error 9377 Y N Y N

058 063 Error 9277 Error 9387 Y N Y N

01JAN79 33333 3 3 3 2 2 9 6 543 2 2 0 9 9 7 EC 836600 PEC 835541 A A A A A A A A A A A A K L M N P Q R STU V W MAP 0300-6 A TAPE READ MAP B MAP 0300-7 W C (0. 6 PAGE 7 OF 45

064 069 Error 9397 Error 9487 Y N Y N

065 070 Error 9407 Error 9497 Y N Y N

066 071 I Error 9437 Error 9507 Y N Y N

067 072 Error 9467 Error 9517 Y N Y N

068 073 Error 9477 Error 9527 Y N Y N c

,· C;J-'

01JAN79 c 2 2 2 2 2 2 2 2 1 1 8 5 544 3 2 1 8 6 8 EC 836600 PEC 835541 A A A B B B B B B B B B X Y Z ABC o E F G H J MAP 0300-7 B TAPE READ MAP B MAP 0300-8 J Q 7 PAGE 8 OF 45

074 079 Error 9537 Error 9637 V N Y N / \

075 080 Error 9547 Error 9667 Y N Y N

076 081 Error 9577 Error 9707 Y N Y N

077 082 Error 9587 Error 9737 V N Y N

078 083 Error 9607 Error 9827 V N Y N

01JAN79 11111 1 1 1 1 1 6 5 544 3 3 2 2 2 9 EC 836600 PEC 835541 B B B B B B B B B B B B K L M N P Q R STU V W MAP 0300-8 B TAPE READ MAP C MAP 0300-9 W C (""'" 8 PAGE 9 OF 45

084 089 Error 9837 Error 9897 Y N Y N

085 090 Error 985? Error 9947 Y N Y N

("" 086 091 Error 986? Error 9957 Y N Y N •

087 092 Error 987? Incorrect error number. Y N Go To Map 0900, Entry Point A. 088 Error 988? 093 Y N ERROR 995--WRAP ERROR. No wrap of data through tape control card.

Bad H2 (base I/O) card, Bad tape control card (see MIM 203). c Check/replace the tape unit cable (see MAP 0210 and MIM 230,231).

094 ERROR 994--READ DATA ERROR. Incorrect data detected.

-Attach a jumper between tape control card pin U06 (-write enable) and tape control card pin U08 (gnd) (see MIM 230). - Press EXECUTE

Is ERROR 995 displayed on the display? Y N c

01JAN79 c:' 11111 111 1 1 111 000 EC 836600 PEC 835541 B B Bee C C C C X Y Z ABC o E F MAP 0300-9 c c c TAPE READ MAP c c c C MAP 0300-10 o E F G H J K 999 PAGE 10 OF 45

095 100 Remove jumper. Bad H2 (base I/O) card. Check/replace the tape unit cable (see .~, )II' Bad tape control card (see MIM 203). MAP 0210 and MIM 230,231). Bad read/write head (see MIM 203). Dirty tape head. 101 Check/ adjust the cartridge stop blocks -Probe tape control card pin S09 (-read (see MIM 223). data). Check/replace the tape internal cable (see MAP 0210 and MIM 203). Is the DOWN light on? Y N 096 Remove jumper. 102 Bad tape control card (see MIM 203). Bad H2 (base I/O) card. Bad tape control card (see MIM 203). 103 Check/ replace the tape unit cable (see MAP Check/replace the tape unit cable (see 0210 and MIM 230,231). MAP 0210 and MIM 230,231).

097 104 ERROR 989--READ DATA ERROR. Bad tape control card (see MIM 203). No sync detected on tape channel 0 (format Bad H2 (base I/O) card. track) or on tape channel 1 (data track). Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231). Bad read/write head (see MIM 203). -Probe H2-J06 (-read data). Dirty tape head. (See appendix B, the general logic probe, in the Check/ adjust the cartridge stop blocks (see 5110 MIM). MIM 223). -Leave the probe on the pin. Check/replace the tape internal cable (see MAP 0210 and MIM 203). Is the DOWN light on? V N 105 -If there is a cartridge in the tape drive, remove it. 098 -Remove tape control card (See MIM 203). -Loop on this test (press L on the keyboard). Is the DOWN light on 7 Are both lights on and steady? Y N V N 106 099 Is the UP light on? Is the UP light on? Y N Y N 107 Bad H2 (base I/O) card.

I( 01JAN79 ,~ ~i 1 1 l., .. ' 1 1 EC 836600 PEC 835541 c c c C C C G H J K L M MAP 0300-10 c c c C TAPE READ MAP B B B MAP 0300-11 A B L M X y Z 9 9 1 1 999 o 0 PAGE 11 OF 45

108 116 Bad tape control card (see MIM 203). ERROR 986--READ DATA ERROR. No interrupt detected on tape channel 109 (data track). - Disconnect the tape drive cable Z2 from the board (see MIM 231). Bad tape control card (see MIM 203). Bad read/write head (see MIM 203). 15 the DOWN light on? Check/ replace the tape internal cable (see Y N MAP 0210 and MIM 203). I 110 117 Is the UP light on? ERROR 985--READ DATA ERROR. Y N No interrupt detected on tape channel 0 (format track). 111 Bad H2 (base I/O) card. Bad tape control card (see MIM 203). Bad read/write head (see MIM 203). 112 Check/ replace the tape internal cable (see Check/replace the tape unit cable (see MAP 0210 and MIM 203). MAP 0210 and MIM 230,231). 118 113 ERROR 983--READ DATA ERROR. Bad H2 (base I/O) card. No interrupt detected on either tape channel 0 (format track) or on tape channel 1 (data track). 114 ERROR 988--READ DATA ERROR. -Calibrate the multimeter (see MIM 270). No sync byte detected on tape channel -Measure -5 Vdc between N2-P08 (gnd) and tape (data track). control card pin S06 (-5 Vdc).

Bad tape control card (see MIM 203). Is the voltage in tolerance (-4.6 Vdc to -5.5 Bad read/write head (see MIM 203). Vdc)? Dirty tape head. Y N Check/ adjust the cartridge stop blocks (see MIM 223). 119 -Measure -5 Vdc between N2-P08 (gnd) and 115 E6-D02 (-5 Vdc). ERROR 987--READ DATA ERROR. No sync byte detected on tape channel 0 (format Is the voltage in tolerance (-4.6 Vdc to -5.5 track). Vdc)? Y N Bad tape control card (see MIM 203). Bad read/write head (see MIM 203). c: Dirty tape head. Check/adjust the cartridge stop blocks (see MIM 223).

01JAN79 111 222 EC 836600 PEC 835541 C C C N P Q MAP 0300-11 Bee C TAPE READ MAP B B MAP 0300-12 V N P Q T U 8 1 1 1 8 8 111 PAGE 12 OF 45

120 126 -Measure -5 Vdc between N2-P08 (gnd) ERROR 973--STATUS ERROR. and C1-E11 (-5 Vdc). Tape might be moving too slow.

Is the voltage in tolerance (-4.6 Vdc Check/adjust the motor pulley (see MIM 227). to -5.5 Vdc)? Check/ adjust the cartridge stop blocks (see Y N MIM 223). Inspect the jackshaft housing and the spindle 121 for binds (see MIM 203). The -5 Vdc from the power supply is Check/adjust the magnet gaps (see MIM not in tolerance. 221). Bad tape motor assembly (see M I M 203). Go To Map 0700, Entry Point A. Bad diagnostic tape cartridge. Bad spindle-select arm assembly (see MIM 122 203). Repair the open connection from Bad jackshaft housing assembly (see M I M C1-E11 to E6-D02 . 203).

123 127 Check/replace the tape unit cable (see ERROR 970--STATUS ERROR. MAP 0210 and MIM 230,231). Unexpected beginning or end of tape status active. 124 Bad tape control card (see MIM 203). -Observe which reel of the tape cartridge has the most tape on it. 125 ERROR 982--STATUS ERROR. Does the right reel have more tape on it than BOT Status active once, but it is not active now. the left reel? Y N Bad H2 (base I/O) card. Bad tape control card (see MIM 203). 128 Bad tape LED/PTX assembly (see MIM 203). - Press C to call the tape repositioning option. Check/ replace the tape unit cable (see MAP - Press B to call the reverse tape repositioning 0210 and MIM 230,231). routine. Check/ replace the tape internal cable (see MAP 0210 and MIM 203). Go to Page 1, Step 001, Entry Point A.

129 - Press C to call the tape repositioning option. - Press F to call the forward tape repositioning routine.

Did the tape go forward (counter clockwise motion)? r i 01JAN79 1 1 3 3 EC 836600 PEC 835541 C C R S MAP 0300-12 Bee TAPE READ MAP Bee MAP 0300-13 S R S R T U 8 1 1 8 2 2 PAGE 13 OF 45

130 137 -Press ATTN Check/adjust the motor pulley (see MIM -, ('~ - Probe the tape control card U04 227). -. '---.. (-forward), while repeating the previous Check/adjust the cartridge stop blocks step. (see MIM 223). Inspect the jackshaft housing and the Is the DOWN light on? spindle for binds (see MIM 203). Y N Check/adjust the magnet gaps (see MIM '~' ( 221). J 131 Bad tape motor assembly (see MIM 203). Bad H2 (base I/O) card. Bad diagnostic tape cartridge. Check/ replace the tape unit cable (see Bad spindle-select arm assembly (see MIM MAP 0210 and MIM 230,231). 203). Bad jackshaft housing assembly (see MIM 132 203). Bad tape control card (see M I M 203). 138 133 Tape might be moving too slow. Go to Page 1, Step 001, Entry Point A. Check/adjust the motor pulley (see MIM 227). 134 Check/ adjust the cartridge stop blocks (see ERROR 966--STATUS ERROR. MIM 223). BOT Status cannot be cleared (status bit 7 was Inspect the jackshaft housing and the spindle 0, should have been 1). for binds (see MIM 203). Check/adjust the magnet gaps (see MIM -If you do not know the answer to the next 221). question, answer it N. Bad tape motor assembly (see MIM 203). Bad diagnostic tape cartridge. Is the tape moving too slow? Bad spindle-select arm assembly (see MIM Y N 203). Bad jackshaft housing assembly (see M I M 135 203). - Run the tape speed test by pressing EXECUTE on the keyboard. 139 ERROR 963--STATUS ERROR. Is ERROR 973 now displayed on the Load point hole (BOT status) can not be found display? (status bit 7 was 1, should have been 0). Y N Check/adjust the cartridge stop blocks (see MIM 136 223). Bad H2 (base I/O) card. Bad tape LED/PTX assembly (see MIM 203). Bad tape control card (see MIM 203). c Bad diagnostic tape cartridge.

01JAN79

EC 836600 PEC 835541 C C T U MAP 0300-13 B TAPE READ MAP Bee MAP 0300-14 p N V W 8 8 PAGE 14 OF 45

140 145 ERROR 960--5TATUS ERROR. Remove jumper. BOT Status is not active (status bit 7 was 1, should have been 0). Check/ replace the tape unit cable (see '\.. 1 MAP 0210 and MIM 230,231). -Jumper tape control card pin B08 (gnd) to tape control card pin D10 (+BOT PTX collector) (see 146 MIM 230). Remove jumper. - Try the test again (press R on the keyboard). Bad H2 (base I/O) card. This section of the tape read diagnostic program just ran again. 147 ERROR 958--STATUS ERROR. Is ERROR 960 still displayed? EOT Status cannot be cleared (status bit 0 was V N 1, should have been 0).

141 -If you do not know the answer to the next Remove jumper. question, answer it N.

Bad tape LED/PTX assembly (see MIM 203). Is the tape moving too slow? Check/ replace the tape internal cable (see V N MAP 0210 and MIM 203). 148 142 - Run the tape speed test by pressing -Probe tape control card pin 504 (-BOT). EXECUTE on the keyboard. (See appendix B, the general logic probe, in the 5110 MIM). Is ERROR 973 now displayed? V N Is the DOWN light on 1 V N 149 Bad H2 (base I/O) card. 143 Remove jumper. 150 Check/adjust the motor pulley (see MIM 227). Bad tape control card (see MIM 203). Check/ adjust the cartridge stop blocks (see ,/ MIM 223). 144 Inspect the jackshaft housing and the spindle -Probe H2-U10 (-BOT). for binds (see MIM 203). Check/adjust the magnet gaps (see MIM Is the DOWN light on? 221). V N Bad tape motor assembly (see MIM 203). Bad diagnostic tape cartridge. Bad spindle-select arm assembly (see MIM 203). Bad jackshaft housing assembly (see MIM 203).

01JAN79 1 5 EC 836600 PEC 835541 c c C V W X MAP 0300-14 B C TAPE READ MAP Bee MAP 0300-15 M X L Y Z 8 1 8 4 PAGE 15 OF 45

151 155 Tape might be moving too slow. Remove jumper.

Check/adjust the motor pulley (see MIM 227). Check/replace the tape unit cable (see Check/ adjust the cartridge stop blocks (see MAP 0210 and MIM 230,231). MIM 223). Inspect the jackshaft housing and the spindle 156 for binds (see MIM 203). - Try the test again (press R on the keyboard). Check/adjust the magnet gaps (see MIM 221). Is the message THE PROGRAM IS Bad tape motor assembly (see MIM 203). LOOKING FOR BEGINNING OR END OF Bad diagnostic tape cartridge. TAPE. displayed on the display? Bad spindle-select arm assembly (see MIM Y N 203). Bad jackshaft housing assembly (see MIM 157 203). Remove jumper.

152 Bad tape LEO/PTX assembly (see MIM ERROR 957--STATUS ERROR. 203). EOT Status is not active (status bit 0 was 0, Check/ replace the tape internal cable (see should have been 1). MAP 0210 and MIM 203).

-Attach a jumper between tape control card pin 158 B08 (gnd) to tape control card pin B 10 (+EOT Remove jumper. PTX collector) (see MIM 230). -Probe H2-J02 (-EOT). Bad H2 (base I/O) card. (See appendix B, the general logic probe, in the 5110 MIM). 159 ERROR 954--STATUS ERROR. Is the DOWN light on? Neither BOT nor EOT status is active (status bit Y N o was 0, should have been 1 and status bit 7 was 1, should have been 0). 153 -Probe tape control card pin S02 (-EOT). -If you do not know the answer to the next question, answer it N. Is the DOWN light on? c Y N Is the tape moving too slow or not at all? Y N 154 Remove jumper. 160 Did the tape run off either reel? Bad tape control card (see MIM 203). Y N

~'I 01JAN79 C./ 111 666 EC 836600 PEe 835541 C C D D D Y Z ABC MAP 0300-15 BOD 0 TAPE READ MAP B MAP 0300-16 K ABC H 8 1 1 1 7 555 PAGE 16 OF 45

161 165 - Try the test again (press R on the ERROR 952--COMMAND ERROR. keyboard). Loss of clockwise (reverse) tape direction control. Wait for another error to be displayed on the display. -If you do not remember the answer to the next question, press R and then C to try the test Go to Page 1, Step 001, again. Entry Point A. Did the tape reels move at all after you 162 pressed C? Check/ adjust the cartridge stop blocks Y N (see MIM 223). Bad tape LED/PTX assembly (see MIM 166 203). -If there is a cartridge in the tape drive, Check/ replace the tape internal cable (see remove it. MAP 0210 and MIM 203). - While looking into the front of the tape drive Bad diagnostic tape cartridge. push the spindle (see M I M 203) to the right. Do not push on the rubber part of the spindle. 163 Check/adjust the motor pulley (see MIM 227). While the spindle is pushed to the right, the Check/ adjust the cartridge stop blocks (see tape motor should rotate the spindle. MIM 223). Inspect the jackshaft housing and the spindle Does the spindle rotate? for binds (see MIM 203). Y N Check/adjust the magnet gaps (see MIM 221). 167 Bad tape motor assembly (see MIM 203). There may be foreign material in the select Bad diagnostic tape cartridge. magnet gaps (see MIM 203). Bad spindle-select arm assembly (see MIM Check/ adjust the jackshaft housing (see 203). MIM 220). Bad jackshaft housing assembly (see M I M Check/adjust the magnet gaps (see MIM 203). 221). Bad spindle-select arm assembly (see MIM 164 203). ERROR 953--COMMAND ERROR. Unwanted .tape motion.

There may be foreign material in the select magnet gaps (see MIM 203). Bad brake arm or brake arm spring (see MIM 203). Check/adjust the magnet gaps (see MIM 221). Check/adjust the jackshaft housing (see MIM 220).

01JAN79 1 1 7 7 EC 836600 PEC 835541 o 0 o E MAP 0300-16 o TAPE READ MAP DOD 0 MAP 0300-17 (: E o F G H 1 1 6 6 PAGE 17 OF 45

168 172 -Insert the diagnostic cartridge into the tape Bad select magnet (reverse) (see MIM drive. 203). Check/ replace the tape internal cable ************* (see MAP 0210 and MIM 203). * CAUTION * ************* 173 Tape may run off the reel if the jumper is left on There may be foreign material in the select too long. magnet gaps (see MIM 203). • Check/ adjust the jackshaft housing (see -Momentarily attach a jumper between tape MIM 220). control card pin 012 (-reverse magnet drive) and Check/adjust the magnet gaps (see MIM tape control card pin uoa (gnd) (see MIM 230). 221). - Remove jumper. Bad spindle-select arm assembly (see MIM 203). Did the tape move clockwise (reverse)? Y N 174 Bad tape control card (see MIM 203). 169 -Calibrate the multimeter (see MIM 270). 175 "" ~, (Entry Point H) C -Measure +12 Vdc between tape control card pin 013 (+12 Vdc) and tape control card U08 -If you do not remember the answer to the next (gnd). question, press R and then C to try the test again. Is the voltage in tolerance (+11.0 Vdc to +13.2 Vdc)? Did the tape reels move counterclockwise Y N (forward) rather than clockwise (reverse)? Y N 170 Go to Page 36, Step 423, Entry Point C. 176 -If you do not remember the answer to the 171 next question, press R and then C to try the -If there is a cartridge in the tape drive, test again. remove it. -Remove tape control card (See MIM 203). Did the tape reels move very slowly or - Measure the resistance between tape control slow down after starting? card pin 012 and 013. Y N

Is the resistance 25 to 40 ohms? c Y N

01JAN79 111 888 EC 836600 PEC 835541 DOD DOD F G H J K L MAP 0300-17 DOD TAPE READ MAP B 0 MAP 0300-18 J K L G M 111 7 777 PAGE 18 OF 45

177 185 You have indicated by your answers that -Reinstall the H2 card. the tape reels moved clockwise for about 2 seconds. That is what should happen for Bad tape control card (see MIM 203). this test. You might not have an error. Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231). - Try the test again (press R on the keyboard). 186 ERROR 951--COMMAND ERROR. Go to Page 1, Step 001, Entry Point A. Loss of counterclockwise (forward) tape direction control. 178 There may be foreign material in the select If you do not remember the answer to the next magnet gaps (see MIM 203). question watch for tape motion as you put the cartridge in again. Quickly remove the cartridge 179 if the tape moves. - Probe tape control card pin U04 (-forward) (see 230). Did the tape move as soon as you put the (See appendix B, the general logic probe, in the cartridge in? 5110 MIM). V N - Leave the probe on the pin. 187 Is the DOWN light on'" -If you do not remember the answer to the V N next question, press R and then C to try the test again. 180 Bad tape control card (see MIM 203). Did the tape reels move at all after you pressed C? 181 V N -Remove the H2 (base I/O) card from the board. 188 Is the DOWN light on'" -If there is a cartridge in the tape drive, V N remove it. - Looking into the front of the tape drive, ... 182 watch for spindle rotation (see MIM 203) Is the UP light on? after pressing R and then C on the V N keyboard.

183 Does the spindle rotate? - Reinstall the H2 card. V N

Bad tape control card (see MIM 203).

184 Bad H2 (base I/O) card.

01JAN79 222 1 1 009 EC 836600 PEC 835541 o o 0 0 0 M N P Q R MAP 0300-18 D TAPE READ MAP D D D MAP 0300-19 R T U V 1 ( 8 PAGE 19 OF 45

189 192 -While looking into the front of the tape drive -Power down. push the spindle (see MIM 203) to the left. Do - Unplug the AC line cord. not push on the rubber part of the spindle. - Replug ac power connectors in their proper locations (tape motor connector at While the spindle is pushed to the left, the tape J3 and ac power supply connector at J1 motor should rotate the spindle. (see MIM 207,273).

~".',- Does the spindle rotate? Bad tape motor assembly (see MIM 203). (J' V N Bad tape motor start capacitor (see MIM 203). Check the tape motor cable and • 190 connector. - Open the covers and see if the motor is running. It is difficult to view the motor 193 turning. You might have to view the jackshaft - Power down. pulleys and the drive belt to tell if the motor is -Unplug the AC line cord. turning. - Replug ac power connectors in their proper locations (tape motor connector at J3 and ac Is the motor running? power supply connector at J 1 (see M I M V N 207,273). Test/replace ac wiring (see MIM 273). 191 -Power down. 194 -Unplug theAC line cord for the 5110. Is the jackshaft rotating (see MIM 203)? - Disconnect the power supply ac power V N connector P1 at the ac power box (see MIM 207,273). 195 - Disconnect the tape motor ac power Inspect the jackshaft for frozen bearings. connector P3 at the ac power box (see Bad belt (see M I M 203). MIM 207,273). Check/adjust the motor pulley (see MIM 227). -Connect the tape motor ac power Bad jackshaft housing assembly (see M I M connector (P3) to the power supply ac 203). power connector (J 1). - Plug in the AC line cord. 196 to- - Power up. Wait 25 seconds. There may be foreign material in the select magnet gaps (see MIM 203). c' Does the tape motor run now? Check/adjust the jackshaft housing (see MIM V N 220). Check/ adjust the magnet gaps (see MIM 221). Bad jackshaft housing assembly (see M I M 203). Bad spindle-select arm assembly (see MIM 203).

01JAN79 2 o EC 836600 PEC 835541 D D D D STU V MAP 0300-19 o TAPE READ MAP o 0 DOD MAP 0300-20 S X y 1 ~ 9 w 9 8 8 PAGE 20 OF 45

197 201 -Insert the diagnostic cartridge into the tape Bad select magnet (forward) (see drive. MIM 203). Check/ replace the tape internal cable ************* (see MAP 0210 and MIM 203). * CAUTION * ************* 202 Tape may run off the reel if the jumper is left on There may be foreign material in the too long. select magnet gaps (see MIM 203). Check/ adjust the jackshaft housing (see - Momentarily attach a jumper between tape MIM 220). control card pin B 12 (-forward magnet drive) and Check/ adjust the magnet gaps (see tape control card pin U08 (gnd) (see MIM 230). MIM 221). - Remove the jumper. Bad spindle-select arm assembly (see MIM 203). Did the tape move counterclockwise (forward)? 203 Y N Bad tape control card (see MIM 203).

198 204 -Calibrate the multimeter (see MIM 270). Check/ adjust the cartridge stop blocks (see - Measure +12 Vdc between tape control card MIM 223). pin B 13 (+12 Vdc) and tape control card pin Check/adjust the locking wheels (see MIM U08 (gnd). 222). Bad spindle-select arm assembly (see MIM Is the voltage in tolerance (+11.0 Vdc to 203). +13.2 Vdc)? Bad diagnostic tape cartridge. Y N 205 199 -If you do not remember the answer to the next Go to Page 36. Step 423. Entry Point C. question, press R and then C to try the test again. 200 -If there is a cartridge in the tape drive, Did the tape motion last about 2 seconds? remove it. Y N -Remove tape control card (See MIM 203). - Measure the resistance between tape control 206 card pin B12 and B13 . Bad brake arm or brake arm spring (see MIM 203). Is the resistance 25 to 40 ohms? Bad H2 (base I/O) card. Y N

,_._,-,

01JAN79 " 2 ( .... i 1 EC 836600 PEC 835541 DOD o WX y Z MAP 0300-20 D TAPE READ MAP B D E MAP 0300-21 Z F N A 2 7 1 (- o 8 PAGE 21 OF 45

207 211 -If you do not remember the answer to the next -Probe tape control card pin U04 (-forward) question, press R and then C to try the test (See appendix B, the general logic probe, again. in the 5110 MIM).

Did the tape reels move clockwise (reverse) Is the UP light on? rather than counterclockwise (forward)? Y N Y N 212 208 Bad tape control card (see M I M 203). -If you do not remember the answer to the • next question, press R and then C to try the 213 test again. -Probe H2-J04 (-forward).

Did the tape reels move very slowly or Is the UP light on? slow down after starting? Y N Y N 214 209 Check/ replace the tape unit cable (see You have indicated by your answers that MAP 0210 and MIM 230,231). the tape reels moved counterclockwise for about 2 seconds. That is what should 215 happen for this test. You might not have Bad H2 (base I/O) card. an error. 216 - Try the test again (press R on the There may be foreign material in the select keyboard). magnet gaps (see MIM 203). Bad brake arm or brake arm spring (see MIM Go to Page 1, Step 001, Entry Point A. 203). Check/adjust the magnet gaps (see MIM 210 221). Check/adjust the motor pulley (see MIM 227). Check/ adjust the jackshaft housing (see MIM Inspect the jackshaft and spindle for binds 220). (see M I M 203). There may be foreign material in the select 217 magnet gaps (see MIM 203). ERROR 950--STATUS ERROR. Bad tape motor assembly (see MIM 203). EOT Status is always active (status bit 0 was 1, Bad spindle-select arm assembly (see MIM should have been 0). 203). Bad jackshaft housing assembly (see MIM - Remove the cartridge from the tape drive. 203). Bad diagnostic tape cartridge. Has the tape run off either reel? Y N

01JAN79 2 2 2 2 EC 836600 PEC 835541 E E E A B C MAP 0300-21 BEE TAPE READ MAP E E MAP 0300-22 E B C o E 722 1 1 PAGE 22 OF 45

218 221 The tape is positioned on the end of tape The file protect switch operates electrically. (EOT) mark. Check/adjust the switch assembly (see MIM - Manually move the tape so the EOT mark 224). (hole in tape) is past the mirror (see MIM Check/ adjust the cartridge stop blocks (see 228). MIM 223). - Replace the cartridge in the tape drive. Bad tape switch assembly (see MIM 203). - Try the test again (press R on the Bad diagnostic tape cartridge. keyboard). 222 219 The problem is an electrical problem, not an - Thread the tape back on the reel (see M I M adjustment problem. 229). - Replace the cartridge in the tape drive. - Replace the cartridge in the tape drive. - Try the test again (press R on the keyboard). - Probe tape control card pin 007 (+file protect) (see MIM 230). 220 (See appendix B, the general logic probe, in the (Entry Point F) 5110 MIM).

ERROR 949--STATUS ERROR. Is the DOWN light on 7 File protect status should not be active (status V N bit 6 was 1, should have been 0). 223 - Remove the cartridge from the tape drive. Bad tape switch assembly (see MIM 203). - Determine if the problem is electrical or Check/ replace the tape internal cable (see mechanical by manually pressing the file protect MAP 0210 and MIM 203). switch. (The file protect switch can be seen by looking into the front of the tape drive. It is the 224 leftmost switch. See MIM 203). -Probe tape control card pin U13 (+file protect). -While manually pressing the file protect switch: - Try the test again (press R on the keyboard). Is the DOWN light on7 V N Pressing R caused this section of the tape diagnostic to run again. 225 Bad tape control card (see MIM 203). Is error 949 still displayed on the display7 V N 226 -Probe H2-P04 (+file protect).

Is the DOWN light on 7 V N

227 Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231).

01JAN79 2 3 EC 836600 PEC 835541 E E E o E F MAP 0300-22 B E TAPE READ MAP E MAP 0300-23 o F G 7 2 2 PAGE 23 OF 45

228 231 Bad H2 (base I/O) card. The problem is an electrical problem not an adjustment problem. 229 (Entry Point E) - Replace the cartridge in the tape drive. - Probe tape control card B08 (gnd) (see M I M ERROR 948--STATUS ERROR. 230). Cartridge in place status not active (status bit 3 (See appendix B, the general logic probe, in the was 0, should have been 1). 5110 MIM).

- Remove the cartridge from the tape drive. Is the DOWN light on? - Determine if the problem is electrical or Y N mechanical by manually pressing the cartridge in place switch. The cartridge in place switch can 232 be seen by looking into the front of the tape Bad tape control card (see MIM 203). drive, it is the rightmost switch (see MIM 203). -While manually pressing the cartridge in place 233 switch -Probe tape control card pin B07 (-cartridge in - Try the test again (press R on the keyboard). place).

Pressing R causes this section of the tape read Is the DOWN light on? diagnostic program to run again. Y N (~' Is ERROR 948 still displayed? 234 Y N Bad tape switch assembly (see MIM 203). Check/ replace the tape internal cable (see 230 MAP 0210 and MIM 203). The cartridge in place switch operates electrically. 235 -Probe tape control card pin S12 (-cartridge in Check/adjust the switch assembly (see MIM place). 224). Check/ adjust the cartridge stop blocks (see Is the DOWN light on 1 MIM 223). Y N Bad tape switch assembly (see MIM 203). Bad diagnostic tape cartridge. 236 Bad tape control card (see M I M 203).

237 -Probe H2-M03 (-cartridge in place).

Is the DOWN light on 1 Y N

01JAN79 2 2 4 4 EC 836600 PEC 835541 E E E G H J MAP 0300-23 B BEE TAPE READ MAP E E E MAP 0300-24 A B H J K L M 7 722 3 3 PAGE 24 OF 45

238 245 Check/ replace the tape unit cable (see -Probe H2-G13 (-channel select). MAP 0210 and MIM 230,231). -Leave the probe on the pin.

239 Is the UP light on1 Bad H2 (base I/O) card. Y N

240 246 ERROR 947--WRAP ERROR. Check/ replace the tape unit cable (see No data detected for wrap through the tape MAP 0210 and MIM 230,231). control card. 247 Bad tape control card (see MIM 203). BadH2 (base I/O) card. Bad H2 (base I/O) card. Check/ replace the tape unit cable (see MAP 248 0210 and MIM 230,231). Bad tape control card (see MIM 203). Bad read/write head (see MIM 203). 241 ERROR 946--WRAP ERROR. 249 Missing interrupt for wrap through tape head. -Remove the H2 (base I/O) card from the board. -Probe tape control card pin U09 (-channel -Probe tape control card pin U09 (-channel select). select). - Leave the probe on the pin. (See appendix B, the general logic probe, in the 5110 MIM). Is the DOWN light on 1 Y N Is the DOWN light on 1 Y N 250 Is the UP light on1 242 Y N - Loop on this test (press L on the keyboard). - Probe tape control card pin U09 (-channel 251 select). -Reinstall the H2 card.

Are both lights on and steady1 Bad tape control card (see MIM 203). Y N 252 243 Bad H2 (base I/O) card. Is the UP light on1 Y N 253 -Reinstall the H2 card. 244 Bad H2 (base I/O) card. Bad tape control card (see MIM 203). Bad tape control card (see MIM 203). Check/ replace the tape unit cable (see MAP Check/ replace the tape unit cable (see 0210 and MIM 230,231). MAP 0210 and MIM 230,231).

01JAN79

EC 836600 PEC 835541 E E E K L M MAP 0300-24 A A TAPE READ MAP E MAP 0300-25 y Z P ( 7 7 PAGE 25 OF 45

254 260 ERROR 943--WRAP ERROR. -Probe tape control card pin U02 (+tape clock). Extra data detected for wrap through the tape control card. Is the DOWN light on? Y N - Probe tape control card pin 505 (-diagnostic mode) (see MIM 230). 261 (See appendix B, the general logic probe, in -Probe H2-D06 (+tape clock). the 5110 MIM). - Leave the probe on the pin.

Is the UP light on? Is the UP light on? Y N Y N

255 262 Bad tape control card (see M I M 203). Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231). 256 - Probe H2-G04 (-diagnostic mode). 263 Bad H2 (base I/O) card. Is the UP light on? Y N 264 -Remove the H2 (base I/O) card from the board. 257 - Probe tape control card pin U02 (+tape clock). c Check/ replace the tape unit cable (see -Leave the probe on the pin. MAP 0210 and MIM 230,231). Is the DOWN light on? 258 Y N Bad H2 (base I/O) card. 265 259 Is the UP light on? ERROR 940--WRAP ERROR. Y N No interrupt detected for wrap through tape control card. 266 - Reinstall the H2 card. - Probe tape control card pin U02 (+tape clock) (see MIM 230). Bad tape control card (see M I M 203). c (See appendix B, the general logic probe, in the Check/ replace the tape unit cable (see 5110 MIM). MAP 0210 and MIM 230,231).

Are both lights on and steady? 267 Y N Bad H2 (base I/O) card.

268 Bad tape control card (see MIM 203). Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231).

01JAN79 2 6 EC 836600 PEC 835541 E E N P MAP 0300-25 E TAPE READ MAP E MAP 0300-26 N S 2 5 PAGE 26 OF 45

269 277 - Probe tape control card pin U06 (-write enable). -Probe H2-G08 (-read clock). Is the DOWN light on? V N Is the DOWN light on? V N 270 - Loop on this test (press L on the keyboard). 278 - Probe tape control card pin U06 (-write -Probe H2-G08 (-read clock). enable). - Leave the probe on the pin.

Are both lights on and steady? Is the UP light on? V N V N

271 279 Is the UP light on? Bad H2 (base I/O) card. V N 280 272 -Probe tape control card pin S10 (-read clock). Bad H2 (base I/O) card. Bad tape control card (see MIM 203). Is the DOWN light on? Check/ replace the tape unit cable (see V N MAP 0210 and MIM 230,231). 281 273 Bad H2 (base I/O) card. -Probe H2-G03 (-write enable). Bad tape control card (see M I M 203). - Leave the probe on the pin. Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231). Is the DOWN light on? V N 282 Check/ replace the tape unit cable (see MAP 274 0210 and MIM 230,231). Bad H2 (base I/O) card. 283 275 -If there is a cartridge in the tape drive, remove it. Check/ replace the tape unit cable (see -Remove tape control card (See MIM 203). MAP 0210 and MIM 230,231). -Probe H2-G08 (-read clock). - Leave the probe on the pin. 276 Is the DOWN light on"1 -Probe H2-G08 (-read clock). V N / Are both lights on and steady? V N

01JAN79 2 2 2 2 8 7 7 7 EC 836600 PEC 835541 E E E E E Q R S T U MAP 0300-26 E E E TAPE READ MAP E MAP 0300-27 R T U W 222 ( 666 PAGE 27 OF 45

284 291 -If there is a cartridge in the tape drive, remove it. Is the UP light on? -Remove tape control card (See MIM 203). . (y V N -Measure -12 Vdc between tape control card pin U08 (gnd) and tape control card pin S 13 (-12 285 Vdc). Bad H2 (base I/O) card. Check/ replace the tape unit cable (see Is the voltage in tolerance (-11.0 Vdc TO -13.2 MAP 0210 and MIM 230,231). Vdc)? I V N 286 Bad tape control card (see MIM 203). 292 -Install the tape control card (see MIM 203). 287 -Measure -12 Vdc between N2-P08 (gnd) and - Disconnect the tape drive cable Z2 from the G6-A02 (-12 Vdc). board (see MIM 231). Is the voltage in tolerance (-11.0 Vdc TO Is the DOWN light on? -13.2 Vdc)? V N V N

288 293 Check/ replace the tape unit cable (see -Measure -12 Vdc between N2-P08 (gnd) MAP 0210 and MIM 230,231). and C1-E13 (-12 Vdc).

289 Is the voltage in tolerance (-11.0 Vdc TO Bad H2 (base I/O) card. -13.2 Vdc)? V N 290 -Calibrate the multi meter (see MIM 270). 294 - Measure -12 Vdc between tape control card pin The -12 Vdc from the power supply is U08 (gnd) and tape control card pin S13 (-12 not in tolerance. Vdc) (see MIM 230). Go To Map 0700, Entry Point A. Is the voltage in tolerance (-11.0 Vdc TO -13.2 Vdc)? 295 V N Repair the open connection from C1-E13 to G6-A02.

296 Check/replace the tape unit cable (see MAP 0210 and MIM 230,231).

297 Bad tape control card (see MIM 203).

01JAN79 2 8 EC 836600 PEC 835541 E E V W MAP 0300-27

i,.",.. ",,,~,,~·,,,,,,,,,,,,,,,,,, E E TAPE READ MAP AE E MAP 0300-28 X X y ~ ~ 7 1/ t 6 7 PAGE 28 OF 45 ,,~. ,1'1

298 302 -If there is a cartridge in the tape drive, Is the UP light on1 remove it. V N -Remove tape control card (See MIM 203). '" .1' - Test the continuity of a wire in the tape 303 internal cable (probe on the cable not on the Bad tape control card (see MIM 203). card) by testing for continuity from tape Check/replace the tape unit cable (see control card pin B09 (raw data) to tape MAP 0210 and MIM 230,231). control card pin 009 (raw data) (see MIM 230). 304 Bad H2 (base I/O) card. Is there continuity between the pins? V N 305 Bad tape control card (see MIM 203). 299 Check/ replace the tape unit cable (see MAP Bad tape control card (see MIM 203). 0210 and MIM 230,231). Check/ replace the tape internal cable (see MAP 0210 and MIM 203). 306 ERROR 939--INTERRUPT ERROR. 300 Incorrect interrupt response. ************* * CAUTION * - Probe tape control card pin 505 (-diagnostic ************* mode) (see MIM 230). A bad read / write head can cause the tape (See appendix B, the general logic probe, in the control card to go bad. GO TO ERROR 004 to 5110 MIM). check out the read / write head, before replacing the tape control card. Is the DOWN light on1 V N Bad tape control card (see MIM 203). Bad H2 (base I/O) card. 307 Check/ replace the tape unit cable (see MAP Bad tape control card (see MIM 203). 0210 and MIM 230,231). Bad H2 (base I/O) card. Bad read/write head (see MIM 203). Check/ replace the tape internal cable (see 308 MAP 0210 and MIM 203). -Remove the H2 (base I/O) card from the board. -Probe tape control card pin 505 (-diagnostic 301 mode). -Remove the H2 (base I/O) card from the board. - Leave the probe on the pin. -Probe tape control card pin U06 (-write enable). - Leave the probe on the pin. Is the DOWN light on 1 V N Is the DOWN light on 1 / V N

01JAN79 / 2 2 9 9 EC 836600 PEC 835541 E E E F X y Z A MAP 0300-28 A E F TAPE READ MAP A F MAP 0300-29 V Z A U B 622 6 8 8 PAGE 29 OF 45

309 317 -Probe tape control card pin 012 (-reverse Is the UP light on1 select magnet). ".."11 .. ( .J 'V N .. -" Is the UP light on 1 310 V N - Reinstall the H2 card. 318 Bad tape control card (see MIM 203). Bad tape control card (see MIM 203).

311 319 • Bad H2 (base I/O) card. -Probe tape control card pin U05 (-run).

312 Is the UP light on1 - Reinstall the H2 card. V N

Bad tape control card (see MIM 203). 320 Check/ replace the tape unit cable (see MAP Bad tape control card (see MIM 203). 0210 and MIM 230,231). 321 313 -Probe H2-M13 (-run). ERROR 938--STATUS ERROR. Select magnet active status for reverse Is the UP light on? c operation should be active (status bit 2 was 1, V N should have been 0). 322 -Probe H2-P11 (-select magnet active) Check/ replace the tape unit cable (see (See appendix B, the general logic probe, in the MAP 0210 and MIM 230,231). 5110 MIM). 323 Is the UP light on1 Bad H2 (base I/O) card. V N 324 314 ERROR 937--STATUS ERROR. .. Bad H2 (base I/O) card. Select magnet active status for forward operation should be active (status bit 2 was 1, c' 315 should have been 0). - Probe tape control card pin U 12 (-select magnet active) (see MIM 230). -Probe H2-P11 (-select magnet active). (See appendix B, the general logic probe, in the Is the UP light on1 5110 MIM). V N c Is the UP light on1 316 V N Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231).

01JAN79 3 3 o 0 EC 836600 PEC 835541 F F F B C D MAP 0300-29 F F TAPE READ MAP A MAP 0300-30 C 0 T 2 2 6 9 9 \~. ,J PAGE 30 OF 45

325 335 Bad H2 (base I/O) card. ERROR 936--STATUS ERROR. Select magnet active status was active, should 326 not have been active(status bit 2 was 1, should -Probe tape control card pin U12 (-select magnet have been 0). active) (see MIM 230). -Probe H2-P11 (-select magnet active). Is the UP light on 7 (See appendix B, the general logic probe, in the Y N 5110 MIM).

327 Is the DOWN light on? Check/ replace the tape unit cable (see MAP Y N 0210 and MIM 230,231). 336 328 Bad H2 (base I/O) card. - Probe tape control card pin B 12 (-forward select magnet). 337 -Probe tape control card pin U05 (-run) (see MIM Is the UP light on 7 230). Y N Is the DOWN light on 7 329 Y N Bad tape control card (see MIM 203). 338 330 -Probe tape control card pin B13 (+12 Vdc). -Probe tape control card pin U05 (-run). Is the UP light on7 Is the UP light on7 Y N Y N 339 331 Bad tape control card (see MIM 203). Bad tape control card (see MIM 203). 340 332 -Probe tape control card pin B12 (-forward -Probe H2-M13 (-run). select magnet).

Js the UP light on 7 Is the UP light on 7 Y N Y N

333 341 Check/ replace the tape unit cable (see MAP Bad tape control card (see MIM 203). 0210 and MIM 230,231). Bad select magnet (forward) (see MIM 203). 334 Check/ replace the tape internal cable (see Bad H2 (base I/O) card. MAP 0210 and MIM 203).

/ '" 01JAN79 3 3 '~, __ i 1 1 EC 836600 PEC 835541 F F E F MAP 0300-30 F TAPE READ MAP F F MAP 0300-31 F E G o3 o3 PAGE 31 OF 45

342 350 -Probe tape control card pin 013 (+12 Vdc). - Disconnect the tape drive cable Z2 from the board (see MIM 231). Is the UP light on1 Y N Is the DOWN light on1 Y N 343 Bad tape control card (see MIM 203). 351 ,,, "'".' Check/ replace the tape unit cable (see I C 344 MAP 0210 and MIM 230,231). - Probe tape control card pin 012 (-reverse select magnet). 352 Bad H2 (base I/O) card. Is the UP light on1 Y N 353 - Remove the H2 (base I/O) card from the board. 345 -Probe tape control card pin U05 (-run). Bad tape control card (see MIM 203). -Leave the probe on the pin. Bad select magnet (reverse) (see MIM 203). Check/ replace the tape internal cable (see Is the DOWN .Iight on 1 MAP 0210 and MIM 203). Y N

346 354 -If there is a cartridge in the tape drive, remove it. -Remove tape control card (See MIM 203). Is the UP light on 1 -Probe H2-P11 (-select magnet active). Y N - Leave the probe on the pin. 355 Is the DOWN light on 1 Bad tape control card (see MIM 203). Y N 356 347 Bad H2 (base I/O) card. Is the UP light on1 Y N 357 Bad tape control card (see MIM 203). 348 Check/ replace the tape unit cable (see MAP Bad H2 (base I/O) card. 0210 and MIM 230,231).

349 Bad tape control card (see MIM 203). c

01JAN79

EC 836600 PEe 835541 F G MAP 0300-31 A TAPE READ MAP A F F MAP 0300-32 S R H J 6 6 {,,-): PAGE 32 OF 45

358 365 ERROR 933--STATUS ERROR. - Disconnect the tape drive cable Z2 from Erase active status for tape track channel 1 the board (see MIM 231). should be active (status bit 4 was 0, should have been 1). Is the DOWN light on 1 Y N -Probe H2-U09 (-erase inactive). (See appendix B, the general logic probe, in the 366 5110 MIM). Check/ replace the tape unit cable (see MAP 0410 and MIM 230,231). Is the DOWN light on 1 Y N 367 Bad H2 (base I/O) card. 359 Bad H2 (base I/O) card. 368 -Probe H2-S08 (-channel 1 erase). 360 -Probe tape control card pin U11 (-channel 1 Is the UP light on 1 erase) (see M I M 230). Y N

Is the UP light on1 369 Y N Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231). 361 -If there is a cartridge in the tape drive, 370 remove it. Bad H2 (base I/O) card. -Remove tape control card (See MIM 203). -Probe H2-U09 (-erase inactive). 371 - Leave the probe on the pin. ERROR 930--STATUS ERROR. Erase active status for tape channel 0 should be Is the DOWN light on 1 active (status bit 4 was 0, should have been 1). Y N -Probe H2-U09 (-erase inactive). 362 (See appendix B, the general logic probe, in the Is the UP light on1 5110 MIM). Y N Is the DOWN light on 1 363 Y N Bad H2 (base I/O) card. 372 364 Bad H2 (base I/O) card. / Bad tape control card (see M I M 203).

01JAN79 3 3 EC 836600 PEC 835541 F F F H J K MAP 0300-32 F TAPE READ MAP A F MAP 0300-33 K P L 3 6 ( 2 PAGE 33 OF 45

373 381 -Probe tape control card pin U10 (-channel 0 - Probe H2-J07 (-channel 0 erase). erase) (see MIM 230). Is the UP light on1 Is the UP light on 1 Y N Y N 382 374 Check/ replace the tape unit cable (see -If there is a cartridge in the tape drive, MAP 0210 and MIM 230,231). remove it. -Remove tape control card (See MIM 203). 383 • -Probe H2-U09 (-erase inactive). Bad H2 (base I/O) card. - Leave the probe on the pin. 384 Is the DOWN light on 1 ERROR 927--STATUS ERROR. Y N Status indicates that the tape drive is in erase mode when it should not be (status bit 4 was 1, 375 should be 0). Is the UP light on 1 Y N -Probe H2-U09 (-erase inactive). (See appendix B, the general logic probe, in the

"" 376 5110 MIM). Bad H2 (base I/O) card, ( /' Is the UP light on1 377 Y N Bad tape control card (see MIM 203). 385 378 Bad H2 (base I/O) card. - Disconnect the tape drive cable Z2 from the board (see MIM 231). 386 -Probe tape control card pin S03 (-erase inactive) Is the DOWN light on 1 (see MIM 230). Y N Is the UP light on1 379 Y N Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231). 387 Check/ replace the tape unit cable (see MAP 380 0210 and MIM 230,231). Bad H2 (base I/O) card.

01JAN79 3 4 EC 836600 PEC 835541 F F L M MAP 0300-33 F TAPE READ MAP A MAP 0300-34 M N 3 6 3 PAGE 34 OF 45

388 395 -Probe tape control card pin U10 (-channel 0 ERROR 924--STATUS ERROR. erase) and pin U11 (-channel 1 erase). EOT Status was active but should not have been active (status bit 0 was 1, should have been 0). Is the DOWN light on for either probe point? Y N -Probe H2-J02 (-EOT). (See appendix B, the general logic probe, in the 389 5110 MIM). Bad tape control card (see MIM 203). Check/ replace the tape internal cable (see Is the DOWN light on 7 MAP 0210 and MIM 203). Y N

390 396 -Remove the H2 (base I/O) card from the board, Bad H2 (base I/O) card. -Probe tape control card pin U10 (-channel 0 erase) 'and pin U11 (-channel 1 erase). 397 -Calibrate the multimeter (see MIM 270). Is the DOWN light on for either probe point? -Measure greater than +1 Vdc between tape Y N control card pin B10 (+EOT PTX collector) and tape control card pin U08 (gnd) (see MIM 230). 391 Is the UP light on for both probe points? Is the voltage greater than 1 Vdc? Y N Y N

392 398 Bad tape control card (see MIM 203). Bad tape control card (see MIM 203). Bad tape LED/PTX assembly (see MIM 203). 393 Check/ replace the tape internal cable (see Bad H2 (base I/O) card. MAP 0210 and MIM 203).

394 399 Bad tape control card (see MIM 203). -If there is a cartridge in the tape drive, remove it. Check/ replace the tape unit cable (see MAP -Remove tape control card (See MIM 203). 0210 and MIM 230,231). -Probe H2-J02 (-EOT). - Leave the probe on the pin.

Is the DOWN light on 7 Y N

400 Is the UP light on? Y N

401 Bad H2 (base I/O) card.

01JAN79 3 3 5 5 EC 836600 PEC 835541 F F N P MAP 0300-34 A F F TAPE READ MAP F F MAP 0300-35 M N P Q R 633 4 4 PAGE 35 OF 45

402 409 Bad tape control card (see MIM 203). Bad tape control card (see MIM 203). Bad tape LED/PTX assembly (see MIM 203). 403 Check/replace the tape internal cable (see - Disconnect the tape drive cable Z2 from the MAP 0210 and MIM 203). board (see MIM 231). 410 Is the DOWN light on 1 -If there is a cartridge in the tape drive, remove it. Y N -Remove tape control card (See MIM 203). -Probe H2-U10 (-BOT). 404 - Leave the probe on the pin. • Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231). Is the DOWN light on 1 Y N 405 Bad H2 (base I/O) card. 411 Is the UP light on 1 406 Y N ERROR 921--STATUS ERROR. BOT Status is active but should not have been 412 active (status bit 7 was 0, should have been 1). Bad H2 (base I/O) card.

-Probe H2-U10 (-BOT). 413 (See appendix B, the general logic probe, in the Bad tape control card (see M I M 203). 5110 MIM). 414 Is the DOWN light on 1 -Disconnect the tape drive cable Z2 from the Y N board (see MIM 231).

407 Is the DOWN light on1 Bad H2 (base I/O) card. Y N

408 415 -Calibrate the multimeter (see MIM 270). Check/replace the tape unit cable (see MAP 0210 and MIM 230,231). - Measure greater than 1 Vdc between tape control card pin D10 (+BOT PTX collector) and 416 tape control card pin U08 (gnd) (see MIM 230). Bad H2 (base I/O) card.

Is the voltage greater than 1 Vdc1 Y N

01JAN79

EC 836600 PEC 835541 F F Q R MAP 0300-35 A TAPE READ MAP F MAP 0300-36 L T 6 PAGE 36 OF 45

417 422 ERROR 918--STATUS ERROR. -Measure +12 Vdc between tape control card pin Status indicates the the LED used for detecting 011 (+12 Vdc) and N2-P08 (gnd). BOT - EaT is not on (status bit 5 was 0, should have been 1). Is the voltage in tolerance (+11.0 Vdc to +13.2 Vdc)1 NOTE: All probes or meter tests for this error V N require that the ground wire of the probe or meter be attached to N2-P08 (gnd) in the 423 5110. (Entry Point C)

-Probe H2-J13 (-LED and erase ok). - Measure +12 Vdc between tape control card (See appendix B, the general logic probe, in the pin S11 (+12 Vdc) and N2-P08 (gnd). 5110 MIM). Is the voltage in tolerance (+11.0 Vdc to Is the UP light on1 +13.2 Vdc)1 ·V N V N

418 424 Bad H2 (base I/O) card. -If there is a cartridge in the tape drive, remove it. 419 -Remove tape control card (See MIM 203). -Probe tape control card pin S07 (-LED and erase -Measure +12 Vdc between tape control ok) (see MIM 230). card pin S11 (+12 Vdc) and N2-P08 (gnd).

Is the UP light on 1 Is the voltage in tolerance (+11.0 Vdc to V N +13.2 Vdc)1 V N 420 Check/ replace the tape unit cable (see MAP 425 0210 and MIM 230,231). -Install the tape control card (see MIM 203). 421 -Measure +12 Vdc between F6-D02 (+12 -Calibrate. the multimeter (see MIM 270). Vdc) and N2-P08 (gnd). -Measure greater than +8 Vdc between tape . control card pin B11 (+LED conducting) and Is the voltage in tolerance (+ 11.0 Vdc N2-P08 (gnd). to +13.2 Vdc)1 V N Is the voltage greater than +8 Vdc1 V N

01JAN79 3 3 3 3 3 3 7 7 7 7 7 7 EC 836600 PEC 835541 F F F F F F F S T U V WX y MAP 0300-36 F F F F F F TAPE READ MAP G MAP 0300-37 S U V WX y A 333 3 3 3 ( 6 6 6 6 6 6 PAGE 37 OF 45

426 434 - Measure +12 Vdc between -If there is a cartridge in the tape drive, remove it. C1-D13 (+12 Vdc) and N2-P08 -Remove tape control card (See MIM 203). (gnd). - Measure +5 Vdc between tape control card pin U03 (+5 Vdc) and N2-P08 (gnd). Is the voltage in tolerance (+11.0 Vdc to +13.2 Vdc)7 Is the voltage in tolerance (+4.6 Vdc to +5.5 Y N Vdc)7 ~.,. Y N I l_ 427 +12 Vdc is not in tolerance. 435 -Install the tape control card (see MIM 203). Go To Map 0700, -Measure +5 Vdc between E6-A04 (+5 Vdc) Entry Point A. and N2-P08 (gnd).

428 Is the voltage in tolerance (+4.6 Vdc to +5.5 Repair the open connection Vdc)7 between C1-D13 and F6-D02. Y N

429 436 Check/replace the tape unit cable -Measure +5 Vdc between J2-U03 (+5 Vdc) (see MAP 0210 and MIM 230,231). and N2-P08 (gnd).

430 Is the voltage in tolerance (+4.6 Vdc to Bad tape control card (see MIM 203). +5.5 Vdc)7 Y N 431 Bad tape control card (see MIM 203). 437 +5 Vdc is not in tolerance 432 Bad tape LED/PTX assembly (see MIM 203). Go To Map 0700, Entry Point A. Check/ replace the tape internal cable (see MAP 0210 and MIM 203). 438 Repair the open connection between 433 J2-U03 and E6-A04 - Measure +5 Vdc between tape control card pin (' U03 (+5 Vdc) and N2-P08 (gnd). 439 Check/ replace the tape unit cable (see MAP Is the voltage in tolerance (+4.6 Vdc to +5.5 0210 and MIM 230,231). Vdc)7 Y N 440 Bad tape control card (see MIM 203).

01JAN79 3 8 EC 836600 PEC 835541 F G Z A MAP 0300-37 F TAPE READ MAP G G G MAP 0300-38 Z BCD 3 7 PAGE 38 OF 45

441 447 - Measure 0 Vdc between tape control card pin Pin F6-A02 is part of the board ground U08 (gnd) and N2-P08 (gnd). plane; it must be ground. Retry this MAP: .l Is the ground voltage in tolerance (0.0 Vdc TO Go to Page 2, Step 007, Entry Point B. 0.3 Vdc)? V N 448 Check/ replace the tape unit cable (see MAP 442 0210 and MIM 230,231). -Measure for 0 Vdc between F6-A02 (gnd). and N2-P08 (gnd). 449 - Test for continuity from tape control card pin Is the ground voltage in tolerance (0.0 Vdc S08 (gnd) to N2-P08 (gnd). TO 0.3 Vdc)? V N Is there continuity between the pins? V N 443 Ground voltage is not in tolerance. 450 -Install the tape control card (see MIM 203). Go To Map 0700, Entry Point A. - Test for continuity from F6-A04 (gDd) to N2-P08 (gnd). 444 Go to Step 445, Entry Point D. Is there continuity between the pins? V N 445 (Entry Point D) 451 - Test for continuity from F6-A02 (gnd) to -If there is a cartridge in the tape drive, remove it. N2-P08 (gnd). -Remove tape control card (See MIM 203). - Test for continuity from tape control card pin Is there continuity between the pins? U08 (gnd) to N2-P08 (gnd). V N

Is there continuity between the pins? 452 V N Pin F6-A02 is part of the board ground plane, it must be ground. 446 Retry this map -Install the tape control card (see MIM 203). - Test for continuity from F6-A02 (gnd) to Go to Page 2, Step 007, N2-P08 (gnd). Entry Point B.

Is there continuity between the pins? 453 V N Repair the open connection between /' F6-A02 and F6-A04 .

01JAN79 3 3 9 9 EC 836600 PEC 835541 G G G G G BCD E F MAP 0300-38 A G G TAPE READ MAP A G MAP 0300-39 KEF H G 633 5 8 8 PAGE 39 OF 45

454 462 Check/replace the tape unit cable (see - Test for continuity from tape control card pin MAP 0210 and MIM 230,231). 007 (+file protect) to pin B08 (gnd).

455 Is there continuity between the pins? Bad tape control card (see M I M 203). Y N

456 463 ERROR 915--STATUS ERROR. Bad tape control card (see MIM 203). I File protect status should be active (status bit 6 was 0, should have been 1). 464 Bad tape switch assembly (see MIM 203). - Probe H2-P04 (+file protect). Check/replace the tape internal cable (see (See appendix B, the general logic probe, in the MAP 0210 and MIM 203). 5110 MIM). Check/adjust the locking wheels (see MIM - Leave the probe on the pin. 222). Check/ adjust the cartridge stop blocks (see Is the DOWN light on 1 MIM 223). Y N 465 457 ERROR 912--STATUS ERROR. (~I Bad H2 (base I/O) card. Cartridge in place status should not be found (bit 3 should be 0). 458 - If there is a cartridge in the tape drive, remove it. -Probe H2-M03 (-cartridge in place). -Remove tape control card (See MIM 203). (See appendix B, the general logic probe, in the 5110 MIM). Is the UP light on1 -Leave the probe on the pin. Y N Is the DOWN light on 1 459 V N - Disconnect the tape drive cable Z2 from the board (see MIM 231). 466 Bad H2 (base I/O) card. Is the UP light on? V N 467 - If there is a cartridge in the tape drive, remove it. 460 -Remove tape control card (See MIM 203). Bad H2 (base I/O) card. Is the UP light on? 461 V N Check/replace the tape unit cable (see MAP 0210 and MIM 230,231).

(: 01JAN79 4 4 o 0 EC 836600 PEC 835541 G G G G H J MAP 0300-39 A G G TAPE READ MAP A MAP 0300-40 G H J F 533 5 9 9 PAGE 40 OF 45

468 475 - Disconnect the tape drive cable 22 from ERROR 907--INTERRUPT ERROR. the board (see MIM 231). Incorrect interrupt response.

Is the UP light on 7 -Probe H2-G08 (-read clock). Y N (See appendix B, the general logic probe, in the 5110 MIM). 469 Bad H2 (base I/O) card. Are both lights on and steady7 Y N 470 Check/ replace the tape unit cable (see 476 MAP 0210 and MIM 230,231). Is the DOWN light on 7 471 Y N - Test for continuity from tape control card pin B07 (- cartridge in place) to pin B08 (gnd). 477 -Probe H2-D13 (-int req 2). Is there continuity between the pins 7 Y N Is the DOWN light on 7 Y N 472 Bad tape control card (see MIM 203). 478 -Remove the A2, B2, and D2 if installed. 473 -Press RESTART. Wait 25 seconds. Bad tape switch assembly (see MIM 203). -Retry loading the TAPE READ TESTS Check/ replace the tape internal cable (see (see M I M section 4, Diagnostic Aids) MAP 0210 and MIM 203). Did you get an ERROR 9077 474 Y N ERROR 909--WRAP ERROR. Error occurred during a test of the H2 (base I/O) 479 card, no wrap of data. One of the cards you removed is bad. Install each card one at a time, Bad H2 (base I/O) card. pressing RESTART and retrying the TAPE READ TEST after each card is installed. The card which causes a 907 error is bad.

480 Bad H2 (base I/O) card. Bad J2 (processor) card (see MAP 050 for jumpering). Bad tape control card (see MIM 203). Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231). 4 "',

01JAN79 "'...... J' 444 111 EC 836600 PEC 835541 G G G K L M MAP 0300-40 G G TAPE READ MAP G MAP 0300-41 L M K 4 4 4 o 0 o PAGE 41 OF 45

481 489 Bad J2 (processor) card (see MAP 050 for -Calibrate the multimeter (see MIM 270). jumpering). - Measure -5 Vdc between N2-P08 (gnd) and tape control card pin S06 ( -5 Vdc). 482 -If there is a cartridge in the tape drive, remove it. Is the voltage in tolerance (-4.6 Vdc to -5.5 -Remove tape control card (See MIM 203). Vdc)? -Probe J2-G08 (-read clock). Y N -Leave the probe on the pin. I 490 Is the DOWN light on? -If there is a cartridge in the tape drive, Y N remove it. -Remove tape control card (See MIM 203). 483 -Measure -5 Vdc between N2-POB (gnd) and Is the UP light on? tape control card pin S06 (-5 Vdc). Y N Is the voltage in tolerance (-4.6 Vdc to -5.5 484 Vdc)? Bad H2 (base I/O) card. Y N

485 491 Bad tape control card (see MIM 203). -Install the tape control card (see MIM c" 203). 486 -Measure -5 Vdc between N2-POB (gnd) - Disconnect the tape drive cable Z2 from the and E6-D02 ( -5 Vdc). board (see MIM 231). Is the voltage in tolerance (-4.6 Vdc to Is the DOWN light on? -5.5 Vdc)? Y N YN

487 492 Check/ replace the tape unit cable (see MAP -Measure -5 Vdc between N2-POB (gnd) 0210 and MIM 230,231). and C1-E11 ( -5 Vdc).

488 Is the voltage in tolerance (-4.6 Vdc Bad H2 (base I/O) card. to -5.5 Vdc)? C'~ Y N

493 The -5 Vdc from the power supply is not in tole renee. c" Go To Map 0700, Entry Point A.

01JAN79 c' 4 444 2 2 2 2 EC 836600 PEC 835541 G G G G N P Q R MAP 0300-41 A A G G G G TAPE READ MAP v X Y Z A A MAP 0300-42 DEN P 0 R 455 5 A B 5 5 444 4 5 5 111 1 PAGE 42 OF 45

494 500 Repair the open connection from ERROR 901--STATUS ERROR. C1-E11 to E6-D02 . Status other than FF after an a\l device reset. 495 Check/ replace the tape unit cable Bad H2 (base I/O) card. (see MAP 0210 and MIM 230,231). 501 496 ERROR 014-- SYSTEM ERROR. Bad tape control card (see MIM 203). Device not selected.

497 Bad H2 (base I/O) card. Bad tape control card (see MIM 203). 502 498 ERROR 013-- SYSTEM ERROR. Error 906--status error. Device not attached. Subdevice address response status from internal tape drive not active (status bit 1 was Bad H2 (base I/O) card. 1, should have been 0). 503 Bad H2 (base I/O) card. ERROR 012-- SYSTEM ERROR. Physical end of tape. 499 Error 903--status error. Rewind the diagnostic tape. It may not be Expected ROS status from internal tape drive located correctly. was not active (special status bit 4 was 1, should Bad diagnostic tape cartridge. have been 0). 504 Bad H2 (base I/O) card. ERROR 011-- SYSTEM ERROR. End of marked tape.

Rewind the diagnostic tape. It may not be located correctly. Bad diagnostic tape cartridge.

505 .),.' ERROR 010-- SYSTEM ERROR. End of file.

Rewind the diagnostic tape. It may not be located correctly. Bad diagnostic tape cartridge.

01JAN79

EC 836600 PEC 835541

MAP 0300-42 STU TAPE READ MAP P R G G MAP 0300-43 444 4 4 S T

PAGE 43 OF 45

506 511 ERROR 009--SYSTEM ERROR. The problem is in one of the I/O devices End of data. that was attached to the 5110 I/O interface port. Bad diagnostic tape cartridge. Connect the I/O devices up one at a time to the 5110. Use the cable 507 terminator to terminate the I/O device if --".'." \:, ERROR 008-- SYSTEM ERROR. available, otherwise use the 5103 as the Records / signals out of sequence (position terminating device. ( / I error). Rerun the failing diagnostic again for each I/O device you attach. The device Bad diagnostic tape cartridge. that causes the ERROR 007 to appear is Dirty tape head. bad. Check/ adjust the cartridge stop blocks (see The most likely cause of the problem is MIM 223). either a bad adaptor card in that device, Bad tape control card (see MIM 203). the I/O interface cable for that device, the cables that go out to that devices 508 interface port, or the cable terminator. ERROR 007-- SYSTEM ERROR. Unrecoverable data error (CRC error). 512 Bad diagnostic tape cartridge. Is there a cable attached to the 5110 I/O Dirty tape head. interface port? Bad tape control card (see MIM 203). Y N Bad A2 (I/O cable driver) card and cable assembly. 509 Bad diagnostic tape cartridge. 513 Dirty tape head. ERROR 006-- SYSTEM ERROR. Check/ adjust the cartridge stop blocks (see File protect on. Same as error 949. MIM 223). Bad tape control card (see MIM 203). Go to Page 22, Step 220, Entry Point F. Bad A2 (I/O cable driver) card and cable assembly. 514 ERROR 005-- SYSTEM ERROR. 510 Cartridge not inserted. Same as error 948. -Disconnect the cable at the 5110 I/O interface c port. Go to Page 23, Step 229, Entry Point E. - Try to load the diagnostic again.

Does ERROR 007 appear again? Y N

c 01JAN79 EC 836600 PEC 835541 G G S T MAP 0300-43 N TAPE READ MAP L MG MAP 0300-44 4 4 4 U

PAGE 44 OF 45

515 521 ERROR 004-- SYSTEM ERROR. - Measure the resistance between tape Timeout control card pin 006 (-channel 1 coil) and D05 (+channei i center tap). -If there is a cartridge in the tape drive, remove it. -Remove tape control card (See MIM 203). Is the resistance between 6 ohms and - Measure the resistance between tape control 15 ohms? card pin B04 (+channel 0 coil) and B05 (+channel Y N o center tap) (see MIM 230). 522 Is the resistance between 6 ohms and 15 Bad read/write head (see MIM 203). ohms? Check/ replace the tape internal cable Y N (see MAP 0210 and MIM 203).

516 523 Bad' read/write head (see MIM 203). Rewind the diagnostic tape. It may not be Check/ replace the tape internal cable (see located correctly. MAP 0210 and MIM 203). Bad diagnostic tape cartridge. Dirty tape head. 517 Bad read/write head (see MIM 203). - Measure the resistance between tape control Bad tape control card (see MIM 203). card pin B06 (-channel 0 coil) and B05 (+channel Check/ replace the tape internal cable (see o center tap). MAP 0210 and MIM 203).

Is the resistance between 6 ohms and 15 524 ohms? ERROR 003-- SYSTEM ERROR. Y N Machine error.

518 Bad H2 (base I/O) card. Bad read/write head (see MIM 203). Bad tape control card (see M I M 203). Check/ replace the tape internal cable (see Check/ replace the tape unit cable (see MAP MAP 0210 and MIM 203). 0210 and MIM 230,231).

519 525 - Measure the resistance between tape control ERROR 002-- SYSTEM ERROR. card pin 004 (+channel 1 coil) and 005 Command error. Incorrect command detected. (+channel 1 center tap). Go To Map 0900, Entry Point A. Is the resistance between 6 ohms and 15 ohms? Y N

520 Bad read/write head (see MIM 203). Check/ replace the tape internal cable (see MAP 0210 and MIM 203).

01JAN79 ,( }I

EC 836600 PEC 835541 G U MAP 0300-44 A K TAPE READ MAP MAP 0300-45 ( 1 4 PAGE 45 OF 45

526 ERROR 001-- SYSTEM ERROR. A TIN Key pressed during tape I/O.

Did you press ATTN key during tape I/O? Y N

527 Go To Map 0600, Entry Point A. I 528 Go to Page 2, Step 007, Entry Point B.

529 Go To Map 0420, Entry Point A.

c

01JAN79

EC 836600 PEC 835541

MAP 0300-45 This page intentionally left blank.

(,f

MAP 0300-46 DISKETTE READ MAP MAP 0310-1 (:""~I PAGE 1 OF 27

ENTRY POI NTS EXIT POINTS . (c: FROM ENTER THIS MAP EXIT THIS MAP TO MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT

0200 A 001 3 010 0420 A 0900 A 001 2 006 0420 A C,; 23 261 0700 A 2 005 0900 A 3 009 0900 A 27 315 420 A I

001 (Entry Point A)

Is the PROCESS CHECK light on7 Y N

002 If a PROCESS CHECK occurs while using the MOl, reload the MOL If the PROCESS CH ECK persists, go to MAP 420, Entry Point A.

Make sure the diskette is not damaged and the problem occurs on more than one customer diskette before using the MOL

Look for any of the following obvious defects. If defects are found, repair or replace the failing components.

Foreign material in the diskette or diskette drive Belt off or damaged Broken cover/pivots Loose pulleys Accessing band broken or damaged Loose cables or cards c Pulleys not turning Fan not turning (Step 002 continues)

CI © Copyright IBM Corp. 1979 01JAN79 2 EC 836600 PEC 835541 7 A MAP 0310-1 DISKETTE READ MAP MAP 0310-2

PAGE 2 OF 27

(Step 002 continued)

Is the diskette difficult to insert or remove from the drive? V N

003 (Entry Point B)

If there is a diskette in Drive 1, remove it.

-Press RESTART and wait 25 seconds.

Use the keys in the Numeric Key section of the keyboard.

-Press HOLD -Hold CMD and press -(minus key)

If the DCP program loads correctly, the characters DCP will be displayed.

Are the characters DCP displayed? V N

004 Is the PROCESS CHECK light on1 V N

005 Go To Map 0900, Entry Point A.

006 Go To Map 0420, Entry Point A.

01JAN79 2 EC 836600 PEC 835541 7 3 B C MAP 0310-2 C DISKETTE READ MAP MAP 0310-3 ( 2

PAGE 3 OF 27

007 Use the keys in the Numeric Key section.

-Hold CMD and press * (BASIC multiply key). or -Hold CMD and press X (APL multiply key).

If the diagnostic mode loads correctly, the characters DIAG DCP will be displayed (See section 4, Diagnostic Aids in the 5110 MIM).

Are the characters DIAG DCP displayed? Y N I 008 Is the PROCESS CHECK light on7 Y N

009 Go To Map 0900, Entry Point A.

010 Go To Map 0420, Entry Point A.

011 -Press C -Press 1 -Press EXECUTE.

The following are the tests being run, along with the error number displayed if an error occurs while running the diagnostics.

Test Error Number Subdevice select 001 (': Set write, diag 1 and erase 1 i nes 002 Set read and diag 2 1 i nes 003 Set MFM 004 Set FM 005 Test current select line and status 006 C\ Test head 1 and head o select 008 ,/ Test access 1 i nes 009 Test overrun status 010 Test loop write/read ------.... ---1- 011 1- 012 1- 013 (Step 011 continues)

01JAN79

EC 836600 PEC 835541

MAP 0310-3 DISKETTE READ MAP MAP 0310-4

PAGE 40F 27

(Step 011 continued) New media 014 Index pulse timing 015 Index pulse width 016 Head access test 017 Auto head engage/disengage test 018 Head initialize 019 Sense side 0, cylinder 0 020 Sense side 1, cylinder 0 021 Random access test 022 Load DSP 023

Are the words DISKETTE READ DIAGNOSTIC displayed on the top line of the display? Y N

012 Bad 5110 F2 (Common and Language RDS) card.

013 An error instruction is displayed in the following format:

ERROR XXX DRIVE 1 GO TO MAP 0310.

Is an error instruction displayed? Y N

014 Follow the instructions displayed until the characters DSP MENU are displayed. The diskette diagnostics are being run on DRIVE 1.

Is DSP MENU displayed? Y N

/{ '" 01JAN79~._J

EC 836600 PEC 835541 655 o E F MAP 0310-4 F DISKETTE READ MAP E G MAP 0310-5 4 4

PAGE 5 OF 27

015 023 If the instruction PRESS EXECUTE, R, OR, L is Go to Page 6, Step 029, Entry Point P. displayed, ignore it. 024 Please observe again for: -Insert the CE diagnostic diskette (with the label to to the right) in drive 1. 1. PROCESS CHECK light on. -Enter 881 2. Error displayed. - Press EXECUTE 3. Questions displayed. - Follow the instructions displayed to run the Do you have any of the above conditions 7 diagnostic. Y N If the PROCESS CHECK light comes on, go to 016 MAP 0420 entry point A. Suspect the diskette Were you at this step before 7 adapter card along with any other callouts. Y N If you have swapped cables, be sure to select the 017 proper logical drive number. Go to Page 2, Step 003, Entry Point B. Return the cables to their proper locations after 018 repairing the failing diskette drive (Drive 1 A 104, -Probe A 1C1-G13 (-Put strobe) in the 5114. Drive 2 A 184). C~I Information on the use of the CE probe can b.e found in Appendix B of the 5110 MIM. Did the MOl's run to completion? Y N Is the DOWN light on or pulsing? Y N 025 Follow the instructions displayed on the 019 screen. Bad A2 (I/O cable driver) card and cable assembly in 5110. 026 Check/replace the 5114 internal cables 01 Did you remove a second 5114? and 03 (see 280 and MAP 0210). Y N Check/replace the 5114 I/O interface cable (see 280 and MAP 0210). 027 (~\ No failure found. 020 Bad 5114 C1 (adapter) card (see MAP 050 028 before replacing this card). The trouble is in the 5114-2.

021 Bad 5114 C1 (adapter) card (see MAP 050 before c Is an error message displayed? replacing this card). Y N Check/replace the 5114 internal cables 01 and 03 (see 280 and MAP 0210). 022 Check/replace the 5114 I/O interface cable (see Go to Page 1, Step 001, Entry Point A. 280 and MAP 0210). c 01JAN79 EC 836600 PEC 835541 G MAP 0310-5 D DISKETTE READ MAP N MAP 0310-6 4

PAGE 6 OF 27

029 034 (Entry Point P) Is the error code 0041 Y N Are two 5114's installed on the system? Y N 035 Is the error code 005? 030 Y N Are two drives installed in the 51141 Y N 036 Is the error code 006? 031 Y N (Entry Point E) 037 Is the error code 001 1 Is the error code 0071 Y N Y N

032 038 Is the error code 0021 Is the error code 0081 Y N Y N

033 Is the error code 0031 Y N

01JAN79 2 2 222 2 2 2 2 2 EC 836600 PEC 835541 76211 1 1 0 0 0 7 HJKLMN P Q R STU MAP 0310-6 U DISKETTE READ MAP A MAP 0310-7 6 A

PAGE 7 OF 27

039 044 Is the error code 0091 Is the error code 0141 V N V N

040 045 Is the error code 0101 Is the error code 0151 V N V N

041 046 Is the error code 0111 Is the error code 0161 V N V N

042 047 Is the error code 0121 Is the error code 0171 V N V N

043 048 Is the error code 0131 Is the error code 0181 V N V N

c'

01JAN79 11111 2 2 1 1 1 6 6 6 4 3 8 EC 836600 PEC 835541 o 0 8 8 8 A A A A A A A V WX Y Z A BCD E F G MAP 0310-7 A DISKETTE READ MAP A A MAP 0310-8 G K L 7

PAGE 8 OF 27

049 058 Is the error code 0197 Bad 5114 C1 (adapter) card (see MAP 050 Y N before replacing this card). Bad drive control card. 050 Check/replace the 04 cable in 5114 (see MAP Is the error code 0207 0210). Y N Bad head / carriage assembly. Bad diagnostic diskette. 051 Is the error code 0217 059 Y N - Probe A 1 04-007 (+Select head 1) on the 5114.

052 Is the UP light ON? Is the error code 0227· Y N Y N 060 053 Check/replace the 04 cable in 5114 (see MAP Is the error code 023? 0210). Y N Bad drive control card.

054 061 No error found. -Probe on the diskette drive control card.

055 TPA-5 ... (+Select head 1) Bad CE diagnostic diskette. TPA-13.. (Gnd)

056 Is the UP light ON7 Go to Page 14, Step 149, Y N Entry Point C. 062 057 Bad drive control card. -Press L Check/replace the 04 cable in 5114 (see MAP - Probe A 1 C 1 - U07 (+Select head 1) on the 0210). 5114. Information on the use of the CE probe can 063 be found in Appendix B of the 5110 MIM. Bad head/ carriage assembly. Bad drive control card. Is the UP light ON7 Bad CE diagnostic diskette. Y N Check/replace the 04 cable in 5114 (see MAP 0210).

;f-" 01JAN79 \t}, 1 3 9 EC 836600 PEC 835541 A A A A H J K L MAP 0310-8 A DISKETTE READ MAP A A A MAP 0310-9 J Q R S 8 PAGE 9 OF 27

064 071 -Perform the head load service check (see 5114 Bad drive control card. MIM 130). Bad head load solenoid. Bad drive stepper motor. Is the service check OK? Y N 072 - Ensure diskette drive 1 is plugged into A 1 04. 065 -Unplug drive 2 from A 1 B4. Does the diskette drive have a Taper Pin Replace fuse. Block on the rear of the drive? Y N Does the fuse blow? Y N 066 - Measure +24Vdc on TPA-11 of the drive 073 control card. - Unplug drive 1 from A 1 04. - Plug drive 2 into A 1 04. Is the voltage OK? Y N Does the fuse blow? Y N 067 -Check fuse 2. 074 Bad A1 board in the 5114. C: Is fuse 2 OK? Y N 075 The trouble is in drive 2. 068 -Replace fuse 2. Bad drive control card. Bad head load solenoid. Does the fuse blow again? Bad drive stepper motor. Y N 076 069 Bad drive control card. Bad fuse 2. Bad head load solenoid. Bad drive stepper motor. 070 Is there a second diskette drive 077 installed? Go to Page 11, Step 095, Entry Point J. Y N c

01JAN79 111 100 EC 836600 PEC 835541 A A A A A A M N P Q R S MAP 0310-9 A A DISKETTE READ MAP A MAP 0310-10 N P W 9 9 PAGE 10 OF 27

078 086 -Turn the 51141PO switch off. Is there a second diskette drive installed? - Measure the resistance of the head load Y N solenoid (see LOGIC 440). 087 Is the resistance approximately 140 ohms 7 (Entry Point M) Y N - Turn off the IPO switch. 079 - Unplug the yellow and black cable from the Bad head load solenoid. Taper Pin Block on the back of the drive (see the 5114 MIM 130). 080 - Replace the fuse. Bad drive control card. - Turn on the IPO switch. Check/replace the 04 cable in 5114 (see MAP 0210). Does the fuse blow again] Y N 081 -Measure the +24 Vdc at the Taper Pin Block on 088 the rear of the failing drive (see 5114 MIM 130). Bad resistor, capacitor, or solenoid. +24 Vdc on pin H Bad black and yellow cable or Taper Pin Ground on the ground strap. Block (see 5114 MIM 130).

Is the voltage OK? 089 Y N Bad drive control card. Check/replace the 04 cable in 5114 (see MAP 082 0210). -Measure +24 Vdc on A1 04-010 on the 5114. Bad AC or OC power supply (see LOGIC 440).

Is the voltage OK] 090 Y N - Ensure diskette drive 1 is plugged into A 1 04. -Unplug drive 2 from A1 B4. 083 - Replace the fuse. -Check fuse 2. Does the fuse blow again] Is fuse 2 OK] Y N Y N 091 084 -Unplug drive 1 from A 1.04. - Replace the fuse. - Plug drive 2 into A 1 04.

Does the fuse blow again] Did the fuse blow again] Y N Y N

085 092 Bad fuse 2. Bad 5114 A 1 board.

01JAN79 111 1 1 111 1 1 EC 836600 PEC 835541 A A A A A A T U V W X y MAP 0310-10 A A A A A DISKETTE READ MAP A A MAP 0310-11 T U V X y M Z 11111 9 o 0 000 PAGE 11 OF 27

093 101 Go to Page 10, Step 087, Check the wires and connectors from the Entry Point M. diskette drive control card to the Terminal Pin Block (see LOGIC 440). 094 Bad drive control card. Go to Page 10, Step 087, Check/replace the D4 cable in 5114 (see MAP Entry Point M. 0210).

095 102 (Entry Point J) -Check the head load springs and head load mechanism. -Measure +24 Vdc on A1A4-D10 on the 5114. Does everything look OK mechanically? Y N • Is the voltage OK? Y N 103 Repair or replace the defective components. 096 Bad DC power supply. 104 Bad cable A1A4 to the power supply. Are the head/carriage guide rods seated properly (see 5114 MIM 120)? 097 Y N Bad A 1 board in 5114. 105 098 Adjust the rods. Bad connection from the +24 Vdc to the Taper Pin Block (see LOGIC 440). 106 Bad resistor, capacitor or connection (see -Press L 5114 MIM 130 and LOGIC 440). -ProbeA1D4-B07 (+File Data) on the 5114. Bad drive control card. Are both lights on and steady? 099 Y N -Turn off the 5114. - Measure the resistance of the head load 107 solenoid (see LOGIC 440). Bad 5114 C1 (adapter) card (see MAP 050 before replacing this card). Is the resistance approximately 140 ohms? Check/ replace the D4 cable in 5114 (see MAP Y N 0210). Bad drive control card. 100 Bad head assembly. Bad head load solenoid. Check the wires and connectors from the c' diskette drive control card to the Terminal Pin Block (see LOGIC 440).

01JAN79 c 1 2 EC 836600 PEC 835541 A B Z A MAP 0310-11 B DISKETTE READ MAP B MAP 0310-12 A o 1 1 PAGE 12 OF 27

108 114 -Probe A1C1-P13 (+File Data) on the 5114. Is the drive band OK? Y N Are both lights on and steady? Y N 115 Repair or replace the failing components. 109 Bad 5114 C1 (adapter) card (see MAP 050 116 before replacing this card). -Carefully try to move the head / carriage assembly by hand. 110 On the drive control card, Probe: Does the assembly move easily? TPB-5 (+File Data) Y N TPA-13 (gnd) (See 5114 MIM 173). 117 Bad 5114 C1 (adapter) card (see MAP 050 Are both lights on and steady? before replacing this card). Y N Bad drive control card. Check/replace the 04 cable in 5114 (see MAP 111 0210). Bad drive control card. Check/replace the 04 cable in 5114 (see MAP 118 0210). - Turn off the IPO switch. - Measure the resistance of the stepper motor 112 coils. Measure from TPA-11 (Motor Coil -Turn off the IPO switch on 5114. Common) to: -Move the head assembly to the center of its TPA-10 travel. TPB-10 - Turn on the IPO switch. TPB-11 -Rerun the diagnostics. TPB-12 Each coil should measure approximately 200 Does the head/carriage move to the outside ohms (See 5114 MIM 150 and 173). edge of the diskette? . Y N Is the resistance check OK? Y N 113 (Entry Point N) 119 Check the connections. - Look for obvious mechanical problems. Replace the stepper motor. (See 5114 MIM 150). Are there any obvious problems? Y N 120 Loose pulley screw or broken pulley. Loose or missing band clamp screw. (See 5114 MIM 150).

01JAN79 1 1 3 3 EC 836600 PEC 835541 B B B BCD MAP 0310-12 A A B B DISKETTE READ MAP B MAP 0310-13 F H B C F 7 8 1 1 ('~ 2 2 PAGE 13 OF 27

121 129 Repair or replace the defective -Probe TPB-7 (+HO Engage) on the drive control ( ~"~. components. card (see LOGIC 440). .. ' 122 Is the down light on and the up light pulsing? -Check the mounting screws on the Y N stepper motor. 130 Are they tight? Bad 5114 C1 (adapter) card (see MAP 050 Y N before replacing this card). Bad drive control card. 123 Check/replace the 04 cable in 5114 (see MAP Tighten the screws. 0210). - Perform the head / carriage service check (see 5114 MIM 120). 131 Does the failing drive have a Taper Pin Block 124 at the rear of the drive? - Perform the drive band service check (see Y N 5114 MIM 152). 132 Is the service check OK? - Measure +24Vdc on TPA-11 of the drive

t Y N control card. C/ 125 Is the voltage OK? Repair, replace or adjust the failing Y N components. 133 126 Go to LOGIC 440 to isolate the +24Vdc Bad 5114 C1 (adapter) card (see MAP 050 problem. before replacing this card). Bad drive control card. 134 Check/ replace the 04 cable in 5114 (see Bad drive control card. MAP 0210). Bad head load solenoid. Bad head/ carriage assembly. Bad CE diagnostic diskette. 135 -Measure +24 Vdc at the Taper Pin Block on the 127 rear of the failing drive: Go to Page 12, Step 113, Entry Point N. +24 Vdc on pin H 128 Ground on the ground strap. - Remove the covers and observe the failing drive. (See 5114 MIM 130). - Press L Is the voltage OK? Are the heads loading? Y N Y N

I 01JAN79 c 1 1 1 4 4 4 EC 836600 PEC 835541 B B B B E F G H MAP 0310-13 B DISKETTE READ MAP A B B B MAP 0310-14 H E E G J 1 711 3 3 3 PAGE 14 OF 27

136 144 -Measure +24 Vdc on A1A4-010. Bad connection from the +24 Vdc power supply to the TPB.

Is the voltage OK1 Bad resistor, capacitor or connections I, V N on the Taper Pin Block (see 5114 MIM 130). 137 -Check fuse 2. 145 - Perform the head load service check (see Is the fuse OK1 5114 MIM 130). V N Is the service check 01(1 138 V N - Replace the fuse. 146 Does the fuse blow again 1 Perform the head load adjustment (see V N 5114 MIM 130).

139 147 Bad fuse. Bad drive control card. Bad head load solenoid. 140 Check/ replace the 04 cable in 5114 (see -Turn off the 5114. MAP 0210). -Unplug the yellow and black leads on the Taper Pin Block. 148 - Replace the fuse. No failure found. -Turn on 5114. 149 Does the fuse blow again 1 (Entry Point C) V N -Press L 141 Bad resistor, capacitor, or solenoid. On the 5114, Probe: Bad black and yellow cable (see 5114 A 104-B02 (+Access 0) MIM 130). A 104-B03 (+Access 1) A 104-B04 (+Access 2) 142 A 104-B05 (+Access 3) Bad power supply (see LOGIC 440). Are both lights on for all probe points 1 143 V N Use LOGIC 440 to isolate the +24Vdc problem.

'''\

i( --~ 01JAN79 1 1 ~,._ .. ,r 5 5 EC 836600 PEC 835541 B B B J K L MAP 0310-14 B B DISKETTE READ MAP B MAP 0310-15 K L M 1 1 4 4 PAGE 15 OF 27

150 155 "\ Bad 5114 C1 (adapter) card (see MAP 050 - Perform the head / carriage service check (see ( before replacing this card). 5114 MIM 120). .. ,/ Bad drive control card. Check/replace the 04 cable in 5114 (see MAP Is the service check OK? 0210). Y N

151 156 - Set the drive in a position to allow probing. Failure found.

On the drive control card, Probe: 157 TPB-1 (+Access 0) -Turn on the 5114 IPO switch. TPB-2 (+Access 1) -Observe the stepper motor pulley while carefully TPB-3 (+Access 2) trying to move the head/ carriage assembly. TPB-4 (+Access 3) TPA-13 (gnd) Does the stepper pulley turn'" Y N (See 5114 MIM 173). 158 Are both lights on for all probe points? - Perform the drive band service check (see Y N 5114 MIM 152).

C: 152 Is the service check OK? Bad drive control card. Y N Check/replace the B4 cable in 5114 (see MAP 0210). 159 Repair or replace the failing components. 153 -Turn off the 5114 IPO switch. 160 - Remove the failing drive and check the -Check the idler assembly for binds or broken resistance of each stepper motor coil as follows. parts. On the drive control card, Measure: Are there any binds or broken parts? TPA-10, TPB-10, TPB-11 and TPB-12 to TPA-11 Y N (coil common). Each coil should measure approximately 200 161 ohms. -Check the head/carriage guide rods for (See 5114 MIM 150 and 173). proper seating (see 5114 MIM 120).

Is the resistance check OK? Are the rods seated properly? Y N Y N

154 162 Check the connections. Adjust the rods. Replace the stepper motor. Bad drive control card. c 01JAN79 111 666 EC 836600 PEC 835541 B B B B M N P Q MAP 0310-15 A A A B B B DISKETTE READ MAP B B MAP 0310-16 BCD N P 0 R S 7 7 7 1 1 T 555 I PAGE 16 OF 27 163 171 - Replace the drive control card. -Turn off the 51141PO switch. - Replace the diskette covers and - Try to turn the drive motor by hand. insert the CE diskette. - Retry the diagnostic. Does the motor turn freely 7 Y N Does the drive still fail7 Y N 172 Bad motor. 164 Bad drive control card. 17~ Check the AC distribution in 5114 (see LOGIC 165 440). Check/ replace the B4 cable in 5114 (see MAP 0210). 174 Bad 5114 C1 (adapter) card (see Is the drive belt installed and tracking MAP 050 before replacing this correctly (see 5114 MIM 140)7 card). 'Y N

166 175 Repair / replace the failing Replace the belt and perform the service components. check (see 5114 MIM 140). Run the diskette diagnostics. 167 Adjust and tighten the stepper pulley 176 (see 5114 MIM 151). Does the spindle pulley appear to be turning Bad stepper motor. at the correct speed 7 Bad CE diagnostic diskette. Y N

168 177 Go to Step 170, Entry Point D. Check for loose parts or binds in the drive motor or spindle assemblies. 169 Go to Step 170, Entry Point D. 178 Is the diskette turning7 170 Y N , . (Entry Point D) 179 - Remove the covers and observe the failing drive - Turn off the IPO switch. (See 5114 MIM 110 and 116). - Turn the spindle pulley by hand.

Is the drive motor turning7 Does the diskette turn 7 Y N Y N

01JAN79 111 877 EC 836600 PEe 835541 B B B B B R S T U V MAP 0310-16 B B DISKETTE READ MAP 8 MAP 0310-17 U V W 1 1 (' 6 6 PAGE 17 OF 27

180 189 -Open the cover and remove the diskette. (Entry Point F) - Turn the spindle pulley. On the drive control card, Probe: Does the drive hub turn? TPB-9 (+Index) Y N TPA-13 (gnd) (See LOGIC 440) 181 Replace the drive assembly. Is the down light on and the up light pulsing? Y N 182 - Remove the diskette cover and check the 190 collet assembly (see 5114 MIM 111 and 113). -Perform the PTX/LED alignment (See 5114 MIM 161). Are the collet components free of wear and assembled correctly? Is the PTX/LED alignment OK? Y N Y N

183 191 Replace the worn or broken parts. Bad PTX/ LED. Assemble the collet and cover assemblies. 192 :, 184 Perform the LED and PTX service checks for C/ -Check the cover latch assembly (see 5114 the failing drive (see 5114 MIM 162). MIM 112). Is the LED service check OK? Is the latch functioning properly? Y N Y N 193 185 Bad LED. Replace the bad components. Bad drive control card.

186 194 Replace the drive assembly. Is the PTX service check OK? Y N 187 - Turn on the IPO switch. 195 Bad PTX assembly. Does the diskette turn? Bad drive control card. Y N

188 Check for a loose pulley or a bind in the spindle assembly. Replace the drive assembly if no failures are found.

01JAN79 1 1 c 8 8 EC 836600 PEC 835541 B 8 8 W X y MAP 0310-17 B B DISKETTE READ MAP x Y Z B B MAP 0310-18 X y 7 7 7 T Z 1 1 1 7 7 6 PAGE 18 OF 27

196 203 - Perform the PTX amplifier service check (see Bad 5114 C1 (adapter) card (see 5114 MIM 163). MAP 050 before replacing this card). Bad drive control card. Is the output correct? Bad diskette. Y N Check/replace the D4 cable in 5114 (see MAP 0210). 197 Worn or binding collet assembly (see Bad 5114 C1 (adapter) card (see MAP 050 5114 MIM 114). before replacing this card). Bad drive control card. 204 Check/replace the D4 cable in 5114 (see Go to Page 17, Step 189, MAP 0210). Entry Point F.

198 205 Bad -drive control card. Bad 5114 C1 (adapter) card (see MAP 050 Bad 5114 C1 (adapter) card (see MAP 050 before replacing this card). before replacing this card). Bad A 1 B 1 (VFO) card, if installed (see MAP Check/replace the D4 cable in 5114 (see MAP 050 before replacing this card). 0210). Check/replace the D4 cable in 5114 (see Damaged or dirty index hole in the diskette or MAP 0210). envelope. Bad head / carriage assembly. Bad drive control card. 199 -Probe A 1C1-U13 (+Index) on the 5114. 206 Bad A1 B1 (VFO) card, if installed (see MAP Is the line pulsing? 050 before replacing this card). Y N Bad 5114 C1 (adapter) card (see MAP 050 before replacing this card). 200 -Probe A1 D4-B13 (+Index) on the 5114. 207 On the 5114 measure: Is the line pulsing? +5 Vdc on A1A4-D04. Y N -5 Vdc on A1A4-B10.

201 Are the voltages OK? Check/replace the D4 cable in 5114 (see Y N MAP 0210). Bad drive control card. 208 -Check fuse 1, (+5 Vdc). 202 (See LOGIC 440). Bad A 1 board in the 5114. Is the fuse OK? Y N

01JAN79 f '" 1 1 1 '\ ... l 999 EC 836600 PEC 835541 B C C C Z ABC MAP 0310-18 c DISKETTE READ MAP c c c c C MAP 0310-19 C ABO E F 1 1 1 8 8 8 PAGE 19 OF 27

209 217 (Entry Point G) Check/replace the B4 cable in 5114 (see MAP 0210). - Replace the blown fuse. Bad drive control card.

Does the fuse blow again" 218 V N Check/replace the 04 cable in 5114 .. (see MAP 0210)...... ·.,'I 210 Bad drive control card. L l Bad fuse. 219 211 Bad 5114 C1 (adapter) card (see MAP 050 - Disconnect the cable from A 1 04 to Drive 1 and before replacing this card). A 1 B4 from Drive 2 if installed. Bad A 1 B 1 (VFO) card, if installed (see MAP - Replace the fuse. 050 before replacing this card). Bad cable from the power supply to A 1A4. Does the fuse blow again? Bad DC power supply (see LOGIC 440). Y N 220 212 -Check fuse 3 (-5 Vdc). - Plug in Drive 1 (A 104). (see LOG IC 440).

Did the fuse blow? Is fuse 3 OK? c' V N V N

213 221 Did you disconnect a cable from A 1 84? Go to Step 209, Entry Point G. V N 222 214 Check the +5 Vdc and -5 Vdc again. If they No failure found. are not OK, replace the DC power supply (see (See LOGIC 440). LOGIC 440).

215 223 - Plug in Drive 2 (A 1 B4). -Press L -On the 5114, probe A1C1-B12 (-Interrupt Did the fuse blow? request 2). V N Information on the use of the CE probe can be found in Appendix B of the 5110 MIM. 216 No failure found. Are both lights on and steady? o (See LOGIC 440). V N

01JAN79 2 2 o 0 EC 836600 PEC 835541 c c c c C o E F G H MAP 0310-19 wee DISKETTE READ MAP R S T V MAP 0310-20 7 G H 666 7 1 1 9 9 :( .. ,,) PAGE 20 OF 27

224 229 On the 5114, probe A1A1-B12 (-Interrupt Bad 5114 C1 (adapter) card (see MAP request 2). 050 before replacing this card). Bad A2 (I/O cable driver) card and cable Are both lights on and steady? assembly in 5110. Y N Check/replace the 04 cable in 5114 (see MAP 0210). 225 Check/ replace the 5114 internal cables Bad 5114 C1 (adapter) card (see MAP D1 and D3 (see 280 and MAP 0210). 050 before replacing this card). Check/replace the 5114 I/O interface Bad 5114 B1 (VFO) card, if installed. cable (see 280 and MAP 0210). Check/ replace the 5114 internal cables 01 and 03 (see 280 and MAP 0210). 230 Check / replace the 5114 I/O interface Bad 5114 C1 (adapter) card (see MAP 050 cable (see 280 and MAP 0210). before replacing this card). Bad A2 (I/O cable driver) card and cable 226 assembly in 5110. Bad A2 (I/O cable driver) card and cable Check/replace the D4 cable in 5114 (see assembly in 5110. MAP 0210). Check/replace the 5114 internal cables 01 Check/replace the 5114 internal cables D1 and 03 (see 280 and MAP 0210). and D3 (see 280 and MAP 0210). Check/replace the 5114 I/O interface Check/replace the 5114 I/O interface cable (see 280 and MAP 0210). cable (see 280 and MAP 0210). Bad H2 (base I/O) card. 231 227 Press EXECUTE to bypass this test, then Bad 5114 C1 (adapter) card (see MAP 050 follow the instructions on the display. before replacing this card). Check/ replace the 04 cable in 5114 (see MAP 232 0210). Bad 5114 C1 (adapter) card (see MAP 050 before Bad A 1 B 1 (VFO) card, if installed. (see MAP replacing this card). 050 before replacing this card). Bad A2 (I/O cable driver) card and cable Bad A2 (I/O cable driver) card and cable assembly in 5110. assembly in 5110. Check/replace the D4 cable in 5114 (see MAP Bad 5110 A1L2 (exec ROS) card (see 5110 0210). MAP 050 for jumpering). Check/ replace the 5114 internal cables D 1 and Bad 5110 F2 (Common and Language ROS) D3 (see 280 and MAP 0210). card. Check/replace the 5114 I/O interface cable (see Check/ replace the 5114 internal cables 01 280 and MAP 0210). and 03 (see 280 and MAP 0210). Check/replace the 5114 I/O interface cable (see 280 and MAP 0210).

228 Bad 5114 C 1 (adapter) card (see MAP 050 before replacing this card). f'" 01JAN79 "-,,,] EC 836600 PEC 835541

MAP 0310-20 L M P 0 DISKETTE READ MAP c C MAP 0310-21 666 6 J K

PAGE 21 OF 27

233 237 Bad 5114 C1 (adapter) card (see MAP Bad 5114 C1 (adapter) card (see MAP 050 050 before replacing this card). before replacing this card). Bad A2 (I/O cable driver) card and cable Bad drive control card. assembly in 5110. Check/replace the D4 cable in 5114 (see MAP Check/replace the 04 cable in 5114 0210). (see MAP 0210). Check/replace the 5114 internal cables D1 , Check/replace the 5114 internal cables and D3 (see 280 and MAP 0210). 01 and 03 (see 280 and MAP 0210). Check/replace the 5114 I/O interface cable Check/replace the 5114 I/O interface (see 280 and MAP 0210). cable (see 280 and MAP 0210). 238 234 Is a diskette in the drive? Bad 5114 C1 (adapter) card (see MAP 050 V N • before replacing this card). Bad A2 (I/O cable driver) card and cable 239 assembly in 5110. -Perform the LEO/PTX alignment (see 5114 . Check/replace the 04 cable in 5114 (see MIM 161). MAP 0210). - Perform the LED / PTX service checks (see Check/replace the 5114 internal cables 01 5114 MIM 162 and 163). and 03 (see 280 and MAP 0210). Check/replace the 5114 I/O interface Are the service checks OK? o cable (see 280 and MAP 0210). V N 235 240 Bad 5114 C1 (adapter) card (see MAP 050 Replace the failing components. before replacing this card). Bad A2 (I/O cable driver) card and cable 241 assembly in 5110. Bad 5114 C1 (adapter) card (see MAP 050 Check/replace the 04 cable in 5114 (see MAP before replacing this card). 0210). Bad drive.control card. Check/replace the 5114 internal cables 01 Bad A2 (I/O cable driver) card and cable and 03 (see 280 and MAP 0210). assembly in 5110. Check/replace the 5114 I/O interface cable Check/replace the D4 cable in 5114 (see MAP (see 280 and MAP 0210). 0210). Check/replace the 5114 internal cables 01 236 and 03 (see 280 and MAP 0210). c' -Probe A1A3-B13 (-put strobe) on the 5114. Check/replace the 5114 I/O interface cable (see 280 and MAP 0210). Is the UP light on? V N 242 c Remove the diskette and retry the diagnostic.

01JAN79

0' EC 836600 PEC 835541 c C J K MAP 0310-21 K DISKETTE READ MAP c MAP 0310-22 6 P

PAGE 22 OF 27

243 250 -Perform the'LED and PTX service checks (see - Disconnect the cable from A 1 B4 to the drive. 5114 MIM 162.) Does the fuse blow again? Is the LED service check OK? Y N Y N 251 244 Check/replace the B4 cable in 5114 (see MAP -Measure +5 Vdc at TPB-15 on the diskette 0210). drive control card (ground on the ground Bad drive control card. ~" strap). Bad LED or PTX assemblys.

Is the voltage OK? 252 Y N Is there a 5103 attached? Y N 245 -Check fuse 1 (see 5114 MIM 183 and 253 LOGIC 440). Bad 5114 C1 (adapter) card (see MAP 050 before replacing this card). Is fuse 10K? Bad cable from A 1A4 to the DC power supply. Y N Bad DC power supply (see LOGIC 440).

246 254 - Replace fuse 1. (Entry Point K)

Does the fuse blow again? -Disconnect the 5103 from the 5114. Y N -Insert a new fuse.

247 Does the fuse blow again? Bad fuse. Y N

248 255 - Disconnect the cable from A 1 D4 to the Suspect a short or open in the DC voltage drive. distribution in the 5103 (see LOGIC 430). - Replace the fuse. Check the I/O cables.

Does the fuse blow again? 256 Y N Bad 5114 C1 (adapter) card (see MAP 050 before replacing this card). 249 Bad AlB 1 (VFO) card, if installed (see MAP 050 Check/replace the D4 cable in 5114 before replacing this card). (see MAP 0210). Bad cable from A 1A4 to the power supply. Bad drive control card. Bad DC power supply (see LOGIC 440). Bad LED or PTX assemblys. Bad cable from A 1A2 to the I/O port.

01JAN79 222 443 EC 836600 PEC 835541 C C C C L M NP MAP 0310-22 C DISKETTE READ MAP C MAP 0310-23 N T 2 2 PAGE 23 OF 27

257 266 -Measure +5 Vdc on A1A4B02 on the 5114. -Check fuse 2.

Is the voltage OK? Is the fuse OK? Y N r Y N

258 267 Is a 5103 attached? (Entry Point L) Y N - Replace the fuse. 259 (Entry Point H) Does the fuse blow again? Y N Is the drive motor turning? Y N 268 Bad fuse. 260 -Measure +12 Vdc on A1A4-B12 and 269 -12 Vdc on A1A4-D12 on the 5114. - Disconnect the cable from A 1A4. - Replace the fuse. Are the voltages OK? Y N Does the fuse blow again? C~i Y N 261 Go To Map 0700, Entry Point A. 270 -Unplug the cables at A 1 D4 and A 1 B4 if 262 present. Is the relay inside of the AC box - Replug the A 1 A4 cable. picked? Y N Does the fuse blow? Y N 263 Bad relay R 1. 271 Bad cable to the relay (see LOGIC -Replug the cable at A 1 D4. 440). Does the fuse blow? 264 Y N Missing AC voltages (see LOGIC 440). 272 265 - Replug the cable at A 1 B4. -Measure +24 Vdc on A1A4-D10 in the 5114. Does the fuse blow? Y N Is the voltage OK?

IN 01JAN79 222 2 2 2 222 c' 444 4 4 4 4 4 4 EC 836600 PEC 835541 C C C c C C C C C C Q R S T U V W X Y Z MAP 0310-23 c c c c C C DISKETTE READ MAP C C C C C MAP 0310-24 U V WX y Z L M 0 R S 22222 2 2 2 222 333 3 3 3 2 2 333 PAGE 24 OF 27

273 281 The trouble is fixed. Bad cable A1A4 (See MAP 0210 and LOGIC 440). 274 Bad AC/DC power supply. Check/replace the B4 cable in 5114 Bad A 1 board. (see MAP 0210). Bad 5114 C 1 (adapter) card (see Bad drive control card. MAP 050 before replacing this card). Bad stepper motor. Check/replace the 5114 internal '" Bad head load solinoid, capacitor or cables 01 and 03 (see 280 and MAP resistor (see LOGIC 440). 0210). Check/replace the 5114 I/O 275 interface cable (see 280 and MAP Check/replace the 04 cable in 5114 0210). (see MAP 0210). Bad drive control card. 282 Bad stepper motor. -Disconnect the 5103 from the I/O Bad head load solinoid, capacitor or channel. resistor (see LOGIC 440). - Measure +5 Vdc at A 1A4- B02 on the 5114. 276 Bad A 1A4 cable. Is the voltage OK? Bad 5114 A1 board. Y N

277 283 Bad AC/OC power supply. Go to Page 23, Step 259, Bad cable A1A4 (See LOGIC 440). Entry Point H.

278 284 -Check fuse 4. Look for a short or an open in the DC voltage distribution in the 5103 using Is fuse 4 OK? LOGIC 430. Check the cables from the Y N I/O port to the 5103.

279 285 Go to Page 23, Step 267, Entry Point L. Check/replace the 04 cable in 5114 (see MAP 0210). 280 Bad 5114 A1 board. Bad AC/OC power supply. Bad cable A1A4 (See MAP 0210 and LOGIC 286 440). Bad LED assembly. Bad drive control card. /' 287 Is the PTX service check OK? Y N II 01JAN79 2 2 5 5 EC 836600 PEC 835541 D D A B MAP 0310-24 o 0 DISKETTE READ MAP D D D MAP 0310-25 A B C D E 2 2 4 4 PAGE 25 OF 27

288 295 Bad PTX assembly. Is a 5103 attached? C,~·· Bad drive control card. Y N 289 296 On the diskette drive control card, Measure: Bad 5114 C1 (adapter) card (see MAP +24 Vdc on TPA-8. 050 before replacing this card). -5 Vdc on TPA-9. Bad cable from the power supply to (Ground on the ground strap) A1A4. c Bad DC power supply. (See 5114 MIM 173). 297 Are the voltages OK? Go to Page 22, Step 254, Entry Point K. Y N 298 290 Bad DC power supply. -Check fuse 2 (+24 vdc) and fuse 3 (-5 vdc) in Bad cable A 1A4 to the DC power supply. the 5114. Bad external I/O cable to the printer if attached (see 5114 MIM 183). Are the fuses OK? Y N 299 - Perform the PTX amplifier service check (see 291 5114 MIM 163). Replace the blown fuse. Is the service check OK? Does the fuse blow again? Y N Y N 300 292 Bad drive control card. Bad fuse. 301 293 -Perform the LED/PTX alignment (see 5114 MIM - Disconnect the cables A 1 D4 and A 1 B4. 161 ). - Replace the blown fuse. Is the alignment OK? Does the fuse blow again? Y N Y N 302 294 Adjust the LED / PTX alignment. Bad drive control card. Bad LED or PTX assembly. Bad A 1 D4 or A 1 B4 cable to the drive control card.

01JAN79 (J 2 6 EC 836600 PEC 835541 000 D C D E F MAP 0310-25

( ., ..~.------..... D DISKETTE READ MAP J D D . MAP 0310-26 F 6 G H 2 5 PAGE 26 OF 27

303 306 Check the device address lines. Bad 5114 C 1 (adapter) card (see MAP 050 before replacing' this card). -Press L Check/replace the 5114 internal cables 01 and 03 (see 280 and MAP 0210). On the 5114, probe: Check / replace the 5114 I/O interface A1C1-G03 cable (see 280 and MAP 0210). A1C1-G04 Bad A2 (I/O cable driver) card and cable A1C1-G05 assembly in 5110. A1C1-G06 Bad 5110 A 1 L2 (exec ROS) card (see MAP A1C1-G07 050 for jumpering). A1C1-G08 Bad 5110 A1 F2 (Ros control card. A1C1-G09 Bad cable terminator. A1C1-B10 307 Are BOTH lights on for each of the probed Bad drive control card. lines? Bad 5114 C1 (adapter) card (see MAP 050 V N before replacing this card). Check/replace the 04 cable in 5114 (see MAP 304 0210). Bad 5114 C1 (adapter) card (see MAP 050 Bad head/carriage assembly. before replacing this card). Bad CE diagnostic diskette. / Check/replace the 5114 internal cables 01 \'\. and 03 (see 280 and MAP 0210). 308 Check/replace the 5114 I/O interface cable Have you been here before? (see 280 and MAP 0210). Y N Bad drive control card. Bad Cable from the diskette drive to the 309 adapter board; A 104 (Drive 1) or A 1 B4 (Drive Swap A 1 04 and A 1 B4 cables (Drive 2 is now 2) (see MAP 0210) drive 1 and drive 1 is drive 2). Bad A2 (I/O cable driver) card and cable Go to Page 2, Step 003, Entry Point B. assembly in 5110. Bad H2 (base I/O) card in 5110. 310 Bad cable terminator. After the failing FRU has been isolated, remember to swap the cables back to their 305 original locations (A 1 04 drive 1 and A 1 B4 drive -Probe on the 5114; 2). A1C1-013 +OP code E Go to Page 6, Step 031, Entry Point E. A 1C 1 -G 12 +control strobe

Are BOTH lights on for each of the probed lines? YN

01JAN79 ,~" .'" ~."-~,, EC 836600 PEC 835541 D D G H MAP 0310-26 A B H DISKETTE READ MAP MAP 0310-27 1 2 6

PAGE 27 OF 27

311 The first 5114 in the string of I/O devices attached to the 5110 will be called 5114-1. ''''''''''". The second 5114 will be called 5114-2. ( ," .. ~ -Disconnect 5114-2 and attach the terminator or printer to 5114-1 .

-:-'·~~' Go to Page 2, Step 003, Entry Point B.

j l 312 Are the heads loaded all the time 1 V N

313 Check the head load bail return spring and bail stop screw (see 5114 MIM 130). Preform the head load service check (see 5114 MIM 130). Bad drive control card. Bad 5114 C1 (adapter) card (see MAP 050 before replacing this card).

314 Bad drive control card. Use LOGIC 440 to check for shorts in the head load circuitry.

315 The 5114 MOl cannot be loaded.

Go To Map 420, Entry Point A.

c

01JAN79

EC 836600 PEC 835541

MAP 0310-27

• This page intentionally left blank.

'''''I';-, .•

MAP 0310-28

, .Ii BRING UP MAP 0400 C D MAP 0400-1

PAGE 1 OF 23

ENTRY POINTS 004 Go to Page 2, Step 013, Entry Point D. FROM ENTER THIS MAP 005 MAP ENTRY PAGE STEP -Switch the RUN switch under the covers to NUMBER POINT NUMBER NUMBER RUN. -Switch the DISPLAY REGISTERS switch to 0200 A 1 001 NORMAL. 0200 D 2 013 0900· A 1 001 Is the machine at halt Q1 (See BRINGUP HALTS in the Diagnostic Aids section of the MIM.) 001 V N (Entry Point A) 006 This MAP isolates failures that occur during the Is the machine at halt P1 I bring up test. Y N -Switch the L32-64-R32 switch to 64. 007 Are there any devices attached to the 5110 Is the machine at halt L or N 1 I/O interface port (see MIM 271)1 Y N Y N 008 002 Is the machine at halt J, K or M1 (Entry Point J) Y N

Is there a card in A2, B2, 02 or K21 009 Y N Is the machine at halt H1 Y N 003 (Entry Point M)

-Press RESTART. Wait 25 seconds. -Switch the RUN switch under the covers to NOT RUN. -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. (See DISPLAY REGISTERS in the Diagnostic Aids section in the MIM).

Are all of the characters displayed hex characters (that is 0,1,2,3,4,5,6,7,8,9 A,B,C,D,E,F)1 Y N c © Copyright IBM Corp. 1979 01JAN79 1 1 1 1 1 EC 836600 PEC 835541 6 4 4 0 0 9 6 2 ABC D E F G H J K MAP 0400-1 K BRING UP MAP R MAP 0400-2 1

PAGE 2 OF 23

010 015 Is the machine at halt E1 Check the DISPLAY REGISTERS switch. V N -Probe H6-E02 (-display reg sw). 011 Is the machine at halt C1 Is the DOWN light on 1 V N V N

012 016 Is the machine at halt A 1 Check the L32-64-R32 switch. V N -Ensure that the L32-64-R32 switch is set to 013 64. (Entry Point D) • Probe J6-D04 (-right 32 select) ,

Look for a failure in the R /W storage Is the DOWN light on 1 cards. Y N

-Switch the DISPLAY REGISTERS 017 switch to DISPLAY REGISTERS. If ROLO contains 0002, the processor card -Switch the RUN switch under the is suspect. covers to NOT RUN. -Switch the DISPLAY REGISTERS switch Is there a FFFF in R7L01 to DISPLAY REGISTERS. (See DISPLAV REGISTERS in the -Switch the RUN switch under the covers Diagnostic Aids section in the MIM). to NOT RUN. V N Is ROLO 00021 014 YN Check the RUN switch. 018 -Switch the RUN switch under the Now determine if the POR reset line is covers to RUN. bad. -Switch the DISPLAY REGISTERS switch to NORMAL. -Switch the DISPLAY REGISTERS -Probe H6-C02 (-run switch and not switch to NORMAL. IPL). -Switch the RUN switch under the (See MIM 248 display Z3 socket covers to RUN. locations). -Probe H2-803 (-POR reset). (See appendix 8, the general logic probe, in the 5110 MIM). Is the DOWN light on 1 V N Is the UP light on 1 V N

01JAN79

EC 836600 PEC 835541 6 5 544 44333 L M N P Q R STU V W MAP 0400-2 W BRING UP MAP u V MAP 0400-3 2 2 2

PAGE 3 OF 23

019 024 (Entry Point H) -Probe H2-B03.

Does the machine have an APL-BASIC switch Remove the following cards in order until the (see MIM 205)? DOWN light goes off. The last card removed V N is defective: F2, J2, K4. 020 If the DOWN light remains ON, then: Go to Page 22, Step 222, Entry Point G. Bad L2 (exec ROS) card (see MAP 050 for jumpering). 021 Bad G2 (display) card (see MAP 050 for - Remove E4 (APL ROS) jumpering). -Set the APL-BASIC switch to BASIC Bad H2 (base I/O) card. No more than 25 seconds after RESTART is Bad keyboard PC board (see MIM 251). pressed, the following events should occur: Check/ replace Z4 (keyboard) cable (see Map 1. ABCDEFGH ppears on the top line of the 0210 and MIM 206,255). 5110 display. I 2. ABCDEFGHJKLMNP appears on the top 025 line. -Switch the RUN switch under the covers to 3. The top line is cleared and LOADO appears RUN. once on one and only one line of the 5110 - Probe the card select lines listed below. Record display. conditions other than the DOWN light on and c -Press RESTART. Wait 25 seconds. the UP light off. Do all three events shown above occur in o J2-S10 2 J2-U10 sequence after RESTART is pressed? 1 J2-U13 3 J2-S13. V N Is the DOWN light on and the UP light off for 022 all four probe points? -Install the E4 (APL ROS) card. V N Go to Page 22, Step 222, Entry Point G. 026 023 Are both lights on for any of the four probe Bad E4 (APL ROS) card. points? V N

027 Bad J2 (processor) card (see MAP 050 for jumpering).

028 o -Switch the DISPLAY REGISTERS switch to NORMAL.

Go to Step 019, Entry Point H.

c 01JAN79 EC 836600 PEC 835541 4 X MAP 0400-3

'~"""","~iI"""llll"1""""'I'-"''''IT-'''' '1' l' I ,,~~ ... m""'''''''I'I'''''''''' '11'~' ""'II'II'I""''"''I''I1''lr''~''t'.!I''~II''!II''!IIIIIITr''''''''I!I'I''I'I'''T'!I'~...,.n'''''''~''"''''''''''''''''''''r'''''''I''II'''''''-'~"""I"'~' ~""''''r''''''''~-' "'-"'''~'' ... '' ""1" "" .•• ".",,,,.,,,.,,~ "'I" ""~''''''''''''''''''''''I''"''''''''''''''''''''''''''''''''~'~''''~''~'''''' ",'I"'!"'" ,'"',''' ". "" •• ""'"1''''' '."""~''''''''''''''''~.'''''''''''' '~"""""""''''''''''''''''''"'""~,,,.,,,,,.,,,,,"~,., .....,,., ... ,__ ... ,.... "' __, ... "."'.~_ ••• _ .." .. ,...... ,. ___ ._ .... ,.. , .,,,_._,._ S T X BRING UP MAP MAP 0400-4 223

PAGE 4 OF 23

029 036 -Switch the DISPLAY REGISTERS switch Bad RUN switch (see MIM 201,249). to NORMAL. Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 248,249). Go to Page 3, Step 019, Entry Point H. Bad RESTART switch (see MIM 210).

030 037 -Remove the G2 (display) card. - Power down. - Probe J6-004. - Remove the read / write storage cards from M4, N2, and N4, if installed. Is the DOWN light on? -Switch the RUN switch under the covers to V N RUN. -Switch the DISPLAY REGISTERS switch to 031 NORMAL. Bad G2 (display) card (see MAP 050 for - Power up. Wait 25 seconds. jumpering). Did either LOADO or CLEAR WS (spelled 032 correctly) appear only once on one and only Bad display L32-64-R32 switch. one line of the 5110 display? Check/replace Z3 (display and control panel) V N cable (see MAP 0210 and MIM 248,249). 038 033 -Remove the K4 card if installed - Remove the G2 (display) card. - Press RESTART. Wait 25 seconds. - Probe H6-E02. Did either LOADO or CLEAR WS (spelled Is the DOWN light on? correctly) appear only once on one and V N only one line of the 5110 display? V N 034 Bad G2 (display) card (see MAP 050 for 039 jumpering). Was there a card installed in M4? V N 035 - Reinstall the G2 (display) card. 040 Bad M2 (read/write storage) card. Bad DISPLAY REGISTERS switch (see MIM Bad G2 (display) card (see MAP 050 for 249). jumpering). Check/ replace Z3 (display and control panel) Bad J2 (processor) card (see MAP 050 cable (see MIM 248,249). for jumpering). Bad L2 (exec ROS) card (see MAP 050 for jumpering).

01JAN79

5 EC 836600 PEC 835541 5 5 A Y Z A MAP 0400-4 Y Z A BRING UP MAP M N MAP 0400-5 4 4 A 2 2 4 PAGE 5 OF 23

041 046 -Power down. Halt A is the BUS I N bit test. - Remove the read / write storage card M 2. -Install the card you removed from M4 into - Probe all the bus in bits listed below: the M2 location. H2-Gll 5 H2-P12 0 -Power up. Wait 25 seconds. H2-M07 4 H2-P13 6 H2-MOS 3 H2-S10 P Did either LOADO or CLEAR WS (spelled H2-P09 2 H2-U05 1 C: correctly) appear only once on one and H2-Pl0 7 only one line of the 5110 display? Y N Are all bus in bits UP or pulsing? Y N 042 Bad G2 (display) card (see MAP 050 for 047 jumpering). -Probe the bus in bit that is DOWN. Bad J2 (processor) card (see MAP 050 - Remove the following cards until the for jumpering). DOWN light goes off: Bad L2 (exec ROS) card (see MAP 050 A2, F2, and L2. • for jumpering). Is the DOWN light on? 043 Y N The card that was in M2 is bad. 048 044 Replace the card that caused the DOWN Bad K4 (ROS feature) card (see MAP 050 for light to turn off. jumpering). 049 045 Bad J2 (processor) card (see MAP 050 for One of the read write storage cards removed is jumpering). bad. Power down. Install the cards one at a Bad H2 (base I/O) card. time, (M4 first, then N2, N4), to find the bad card. Power up after each card is installed. Use 050 the preceeding step to determine which card is Bad J2 (processor) card (see MAP 050 for bad. jumpering). Bad H2 (base I/O) card. Bad L2 (exec ROS) card (see MAP 050 for jumpering).

051 Halt C is the op code test. o Bad J2 (processor) card (see MAP 050 for jumpering). Bad H2 (base I/O) card.

c 01JAN79 EC 836600 PEC 835541

MAP 0400-5 J L BRING UP MAP A MAP 0400-6 1 2 E

PAGE 6 OF 23

052 058 Halt E is the interrupt test. Is the recorded RFLO between or including 0000 and 3FFF7 Bad H2 (base I/O) card. Y N Bad J2 (processor) card (see MAP 050 for jumpering). 059 Is the recorded RFLO between or including • 053 4000 and 7FFF? Halt H is the stuck key test, and read/write Y N storage test. 060 Is there a key code on the second line from Bad J2 (processor) card (see MAP 050 for the top of the display? jumpering). Y N Bad L2 (exec ROS) card (see MAP 050 for jumpering). 054 -Switch the DISPLAY REGISTERS switch to 061 DISPLAY REGISTERS. -Power down. -Record RFLO. -Swap M2 and M4 (See DISPLAY REGISTERS in the Diagnostic -Power up. Wait 25 seconds. Aids section in the MIM). -Switch the DISPLAY REGISTERS switch to -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. NORMAL. -Record RFLO. (See DISPLAY REGISTERS in the Diagnostic Is there a card in N4? Aids section in the MIM). Y N -Switch the DISPLAY REGISTERS switch to NORMAL. 055 Is there a card in N2? Is the recorded RFLO between or including Y N 0000 and 3FFF? Y N 056 Is there a card in M4? 062 Y N Bad L2 (exec ROS) card (see MAP 050 for jumpering). 057 Bad J2 (processor) card (see MAP 050 for Bad M2 (read/write storage) card. jumpering). Bad G2 (display) card (see MAP 050 for jumpering). 063 Bad J2 (processor) card (see MAP Bad card is now at M2. 050 for jumpering). Bad L2 (exec ROS) card (see MAP 050 for jumpering).

01JAN79

987 7 EC 836600 PEC 835541 A A A A A BCD E F MAP 0400-6 '"'.-''. A A BRING UP MAP A A A MAP 0400-7 ( o F H J K 6 6 PAGE 7 OF 23

064 070 -Power down. Bad J2 (processor) card (see MAP 050 for c: -Swap M2 and M4 jumpering). - Power up. Wait 25 seconds. Bad l2 (exec ROS) card (see MAP 050 for -Switch the DISPLAY REGISTERS switch to jumpering). DISPLAY REGISTERS. -Record RFLO. 071 (See DISPLAY REGISTERS in the Diagnostic -Power down. Aids section in the MIM). - Remove the N2 and M4 cards -Switch the DISPLAY REGISTERS switch to -Install the N2 card in the M4 location NORMAL. - Power up. Wait 25 seconds. -Switch the DISPLAY REGISTERS switch to Is the recorded RFLO between or including DISPLAY REGISTERS. 0000 and 3FFF? - Record RFLO. Y N (See DISPLAY REGISTERS in the Diagnostic Aids section in the MIM). 065 -Switch the DISPLAY REGISTERS switch to Bad card is now at M4. NORMAL. • 066 Is the recorded RFLO between or including Bad L2 (exec ROS) card (see MAP 050 for 4000 and 7FFF? c jumpering). Y N Bad J2 (processor) card (see MAP 050 for jumpering). 072 Bad G2 (display) card (see MAP 050 for Bad J2 (processor) card (see MAP 050 for jumpering). jumpering). Bad L2 (exec ROS) card (see MAP 050 for 067 jumpering). Is the recorded RFLO between or including 0000 and 3FFF? 073 Y N Bad card is now in M4 location.

068 074 Is the recorded RFLO between or including - Power down. 4000 and 7FFF? -Swap M2 and M4 cards. c Y N - Power up. Wait 25 seconds. -Switch the DISPLAY REGISTERS switch to 069 DISPLAY REGISTERS. Is the recorded RFLO between or -Record RFLO. including 8000 and BFFF? (See DISPLAY REGISTERS in the Diagnostic Y N Aids section in the MIM). c' -Switch the DISPLAY REGISTERS switch to NORMAL. (Step 074 continues)

c' 01JAN79 8 EC 836600 PEC 835541 A A A A G H J K MAP 0400-7 A BRING UP MAP A A MAP 0400-8 G C L 7 6 l.".) PAGE 8 OF 23

(Step 074 continued) 081 Is the machine at halt H? The bad card is now at M4. Y N 082 075 Is the recorded RFLO between or including The bad card is now at M2. 0000 and 3FFF1 Y N 076 Is the recorded RFLO between or including 083 0000 and 3FFF? Is the recorded RFLO between or including Y N 4000 and 7FFF? Y N 077 Bad L2 (exec ROS) card (see MAP 050 for 084 jumpering). Is the recorded RFLO between or Bad J2 (processor) card (see MAP 050 for including 8000 and BFFF? jumpering). Y N

078 085 The bad card is now at M2. Is the recorded RFLO between or including COOO and FFFF1 079 Y N (Entry Point N) 086 -Power down. Bad L2 (exec ROS) card (see MAP -Swap M2 and M4 050 for jumpering). - Power up. Wait 25 seconds. Bad J2 (processor) card (see MAP -Switch the DISPLAY REGISTERS switch to 050 for jumpering). DISPLAY REGISTERS. - Record RFLO. 087 (See DISPLAY REGISTERS in the Diagnostic - Power down. Aids section in the MIM). -Remove N2 and N4. -Switch the DISPLAY REGISTERS switch to -Install N4 in the N2 location NORMAL. - Power up. Wait 25 seconds. -Switch the DISPLAY REGISTERS Is the recorded RFLO between or including switch to DISPLAY REGISTERS. 4000 and 7FFF1 -Record RFLO. Y N (See DISPLAY REGISTERS in the Diagnostic Aids section in the MIM). 080 -Switch the DISPLAY REGISTERS Bad L2 (exec ROS) card (see MAP 050 for switch to NORMAL. jumpering). Bad J2 (processor) card (see MAP 050 for Is the recorded RFLO between or jumpering). including 8000 and BFFF1 Bad G2 (display) card (see MAP 050 for Y N jumpering). f ." 01JAN79 l,_)~ 9 9 999 EC 836600 PEC 835541 A A A A A A L M N P Q R MAP 0400-8 A A A BRING UP MAP H A A A MAP 0400-9 P 0 R 1 B M N 888 688 PAGE 9 OF 23

088 093 Bad L2 (exec ROS) card (see MAP 050 for -Power down. jumpering). -Swap M4 and N2. Bad J2 (processor) card (see MAP 050 for - Power up. Wait 25 seconds. jumpering). -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. 089 -Record RFLO. (.~. The bad card is now at N2. (See DISPLAY REGISTERS in the Diagnostic Aids section in the MIM). 090 -Switch the DISPLAY REGISTERS - Power down. switch to NORMAL. -Swap M4 and N2. - Power up. Wait 25 seconds. Is the recorded RFLO between or -Switch the DISPLAY REGISTERS switch to including 8000 and BFFF7 DISPLAY REGISTERS. Y N -Record RFLO. I (See DISPLAY REGISTERS in the Diagnostic 094 Aids section in the MIM). Bad L2 (exec ROS) card (see MAP -Switch the DISPLAY REGISTERS switch to 050 for jumpering). NORMAL. Bad J2 (processor) card (see MAP 050 for jumpering). Is the recorded RFLO between or including 4000 and 7FFF7 095 Y N The bad card is now at N2.

091 096 Bad L2 (exec ROS) card (see MAP 050 for Go to Page 8, Step 079, Entry Point N. jumpering). Bad J2 (processor) card (see MAP 050 for 097 jumpering). - Use the hex code displayed in positions 5 and 6 of the second line from the top to 092 determine the defective key (see MIM 250). The bad card is now at M4. Bad key module (see MIM 253). Bad keyboard PC board (see MIM 251). (~ Check/ replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255).

098 Bad L2 (exec ROS) card (see MAP 050 for jumpering). c Bad J2 (processor) card (see MAP 050 for jumpering). Bad H2 (base I/O) card. Bad F2 (Common and language ROS) card.

C: 01JAN79

EC 836600 PEC 835541

MAP 0400-9 F G BRING UP MAP A MAP 0400-10 1 1 X

PAGE 10 OF 23

099 105 Bad K4 (ROS feature) card (see MAP 050 for Is there a ROS error code of 007 on the jumpering). bottom line of the display? Y N 100 Halt P is the ROS content test. 106 Is there a ROS error code of 005 on the - Remove the K4 card if installed. bottom line of the display? - Press RESTART. Wait 25 seconds. Y N

Did either LOADO or CLEAR WS (spelled 107 correctly) appear only once on one and only (See appendix 8, the general logic probe, one line of the 5110 display? in the 5110 MIM). Y N - Probe H6-B04 (+APL switch). (See MIM 248,249, display and control 101 panel cable). -Install the K4 card if removed. Note: when the BASIC-APL switch is Is there a ROS 40 ERR on the second line switched, RESTART must be pressed from the top of the display? to initialize the 5110 with the new Y N language.

102 Is the UP light on7 Is there a ROS error code of 001 on the Y N bottom line of the display? Y N 108 Is there an 8 in position 15 of the 103 bottom line of the display? Is there a ROS error code of 002 or Y N 014 on the bottom line of the display? Y N 109 Bad H2 (base I/O) card. 104 Bad J2 (processor) card (see MAP Is there a ROS error code of 008 on 050 for jumpering). the bottom line of the display? Y N 110 Bad F2 (Common and language ROS) card.

01JAN79 1 1 1 1 1 111 44431 111 EC 836600 PEC 835541 A A A A A A A A B STU V WX Y Z A MAP 0400-10 A B BRING UP MAP A A MAP 0400-11 Z A Wy (" 1 1 1 1 o 0 o 0 PAGE 11 OF 23

111 119 - Probe the APL select lines: The following questions all refer to positions 14 and 15 of the bottom line of the display F2-P02 (-sel APL HWDS 0-15359) (the message starts in position 2). F2-P04 (-sel APL HWDS 15360-30719) F2-P05 (-sel APL HWDS 30720-46079) Is 02 displayed? F2-P06 (-sel APL HWDS 46080-61439) Y N

"'" ( Are 3 lines UP and one line DOWN? 120 -- Y N Is 04 displayed? YN 112 Are all 4 lines UP? 121 Y N Is 08 displayed? Y N 113 I - Remove E4 (APL ROS) card. 122 Bad F2 (Common and language ROS) Now are 3 lines UP and one DOWN? card. Y N Bad J2 (processor) card (see MAP 050 for jumpering). 114 Bad H2 (base I/O) card. Bad F2 (Common and language ROS) card. 123 Bad F2 (Common and language ROS) 115 card. Bad E4 (APL ROS) card. 124 116 Bad E4 (APL ROS) card. Bad F2 (Common and language ROS) card. Bad F2 (Common and language ROS) card.

117 125 Bad E4 (APL ROS) card. Bad F2 (Common and language ROS) card.

118 126 Bad H2 (base I/O) card. -Record the bottom line of the display. Bad F2 (Common and language ROS) card. Bad L2 (exec ROS) card (see MAP 050 for Is there an 02 in positions 14 and 15 of the jumpering). bottom line? Bad G2 (display) card (see MAP 050 for Y N jumpering). 127 Is there an 8 in position 15 of the bottom line? Y N II c: 01JAN79 111 322 EC 836600 PEC 835541 B B B BCD MAP 0400-11 B BRING UP MAP B B B MAP 0400-12 / D C E F 1 1 1 1 PAGE 120F 23

128 135 Is there a 4 in position 15 of the bottom line 1 Is the BASIC-APL switch set to BASIC1 Y N Y N

129 136 Bad L2 (exec ROS) card (see MAP 050 for (See MIM 248,249, display and control jumpering). panel cable). Bad J2 (processor) card (see MAP 050 for Bad BASIC-APL switch. jumpering). 137 130 Note: when the BASIC-APL switch is Does the machine have a BASIC-APL switch switched, RESTART must be pressed (see MIM 205)? to initialize the 5110 with the new Y N language.

131 Bad H2 (base I/O) card. (See' appendix B. the general logic. probe. in Bad L2 (exec ROS) card (see MAP 050 for the 5110 MIM). jumpering). -Probe H6-B04 (+APL switch). (See MIM 248,249, display and control panel 138 cable). Bad E4 (APL ROS) card.

Is the DOWN light on 1 139 Y N Does the machine have a BASIC-APL switch (see MIM 205)1 132 Y N Bad E4 (APL ROS) card. 140 133 (See appendix B, the general logic probe, in Bad H2 (base I/O) card. the 5110 MIM). Bad L2 (exec ROS) card (see MAP 050 for -Probe H6-B04 (+APL switch). jumpering). (See MIM 248,249, display and control panel cable). 134 (See appendix B, the general logic probe, in the Is the UP light on1 5110 MIM). V N -Probe H6-B04 (+APL switch). (See MIM 248,249, display and control panel 141 cable). Bad F2 (Common and language ROS) card.

Is the UP light on 1 142 Y N Bad H2 (base I/O) card. Bad L2 (exec ROS) card (see MAP 050 for jumpering).

01JAN79 ~. " 1 3 EC 836600 PEC 835541 B B B E F G MAP 0400-12 B BRING UP MAP A B MAP 0400-13 G V B 1 1 1 (' 2 o 1 PAGE 13 OF 23

143 150 -Probe H6-B04 (+APL switch). -Remove the E4 card. (See appendix B, the general logic probe, in the -Press RESTART. Wait 25 seconds. 5110 MIM). (See MIM 248,249, display and control panel Is the machine at halt P with 02 in cable). positions 14 and 15 of the bottom line? V N Is the DOWN light on 7 V N 151 Bad E4 (APL ROS) card. 144 Is the BASIC-APL switch set to APL7 152 V N - Reinstall the E4 card.

145 Bad F2 (Common and language ROS) card. Check/ replace Z3 (display and control Bad H2 (base I/O) card. panel) cable (see MAP 0210 and MIM Bad J2 (processor) card (see MAP 050 for I 248,249). jumpering). Bad BASIC-APL switch. 153 146 Is there a card in M4 or N2 or N4 (read/write Note: when the BASIC-APL switch is storage cards)? '" '\ switched, RESTART must be pressed to V N C/ initialize the 5110 with the new language. 154 Bad H2 (base I/O) card. Bad J2 (processor) card (see MAP 050 for Bad L2 (exec ROS) card (see MAP 050 for jumpering). jumpering). Bad H2 (base I/O) card. Bad M2 (read/write storage) card. 147 Bad L2 (exec ROS) card (see MAP 050 for Is the BASIC-APL switch set to APL? jumpering). V N 155 148 - Power down. Bad F2 (Common and language ROS) card. -Remove the read/write storage cards in this order: M2, M4, N2, and N4. 149 -Install the last card removed into the M2 card Check/ replace Z3 (display and control panel) location. cable (see MAP 0210 and MIM 248,249). No more than 25 seconds after power up, the Bad BASIC-APL switch. following events should occur: 1. ABCDEFGH appears on the top line of the 5110 display. 2. ABCDEFGHJKLMNP appears on the top line. 3. The top line is cleared and either LOADO or CLEAR WS appears once on one and only one line of the display. (Step 155 continues)

01JAN79

EC 836600 PEC 835541

MAP 0400-13 A A BRING UP MAP B E A B B MAP 0400-14 T U 1 1 S H J 1 1 1 o 0 o PAGE 14 OF 23 (Step 155 continued) 162 -Power up. Bad E4 (APL ROS) card. Bad F2 (Common and language ROS) Do all three events shown above occur card. in sequence after Power Up? Y N 163 Bad L2 (exec ROS) card (see MAP 050 156 for jumpering). Bad J2 (processor) card (see MAP 050 Bad G2 (display) card (see MAP 050 for for jumpering). jumpering). Bad H2 (base I/O) card. Bad H2 (base I/O) card. Bad L2 (exec ROS) card (see MAP 050 Bad F2 (Common and language ROS) for jumpering). card.

157 164 The card that was in M2 is bad. Bad K4 (ROS feature) card (see MAP 050 for jumpering). 158 Bad F2 (Common and language ROS) card. 165 Bad J2 (processor) card (see MAP 050 for Halt Q is bringup complete. jumpering). Bad H2 (base I/O) card. Bad L2 (exec ROS) card (see MAP 050 for Bad L2 (exec ROS) card (see MAP 050 for jumpering). jumpering). Bad H2 (base I/O) card. Bad E4 (APL ROS) card. Bad J2 (processor) card (see MAP 050 for jumpering). 159 Is there a card in E41 166 Y N Is there a card in 821 Y N 160 Bad L2 (exec ROS) card (see MAP 050 for 167 jumpering). (Entry Point P) Bad G2 (display) card (see MAP 050 for jumpering). -Remove the A2, 02, and K2 cards if installed. Bad H2 (base I/O) card. Bad F2 (Common and language ROS) card. No more than 25 seconds after RESTART is pressed, the following events should occur: 161 1. ABCOEFGH appears on the top line of the - Remove the E4 (APL)card. 5110 display. -Press RESTART. Wait 25 seconds. 2. ABCOEFGHJKLMNP appears on the top line. Is ROS 40 error code still displayed? 3. The top line is cleared and either LOAOO Y N or CLEAR WS appears once on one and only one line of the 5110 display.

(Step 167 continues)

f' 01JAN79 ! 1 5 EC 836600 PEC 835541 B B B H J K MAP 0400-14 BRING UP MAP B B MAP 0400-15 K L 1 ( 4 PAGE 15 OF 23

(Step 167 continued) -Press RESTART. 173

Do all three events shown above occur in (Entry Point L) sequence after RESTART is pressed? Y N One of the cards might be defective. Use the symptom from the previous step. Isolate the 168 failure to the A2, 02, or K2 card by removing -Install the A2, 02, and K2 cards again. each card one at a time, pressing RESTART -Press RESTART. Wait 25 seconds. and waiting 25 seconds each time. Observe the 5110 display. When LOADO or CLEAR Go to Page 1, Step 003, Entry Point M. WS appears, the failure is in the last card removed. Replace the bad card. 169 One of the cards is bad. 174 -Power down. -Install the A2, 02, and K2 cards again. - Remove the B2 card. -Press RESTART. Wait 25 seconds. I No more than 25 seconds after power up, the Is the machine at halt A, C, E, H, J or K? following events should occur: (See BRINGUP HALTS in the Diagnostic Aids 1. ABCDEFGH appears on the top line of the section of the MIM.) 5110 display. Y N 2. ABCDEFGHJKLMNP appears on the top line. 3. The top line is cleared and either LOA DO or 170 CLEAR WS appears once on one and only Determine if the paR reset line is bad. one line of the display.

-Probe H2-B03 (-paR reset). -Power up.

Is the DOWN I.ight on? Do all three events shown above occur in Y N sequence after Power Up? Y N 171 The MAP cannot isolate the failure to 175 additional symptoms. Use the machine -Power down. halt code as your symptom. -Install the B2 card. Go to Step 173, Entry Point L. - Power up. Wait 25 seconds. Go to Page 14, Step 167, Entry Point P. 172 Use the probe as a failure indicator. A bad 176 condition is indicated by the DOWN light. Bad B2 (BSCA 1) card. Go to Step 173, Entry Point L.

c 01JAN79 EC 836600 PEC 835541 B L MAP 0400-15 A BRING UP MAP B B B MAP 0400-16 1 M N P

PAGE 16 OF 23

177 181 -Disconnect the cable at the 5110 I/O interface The map cannot isolate the failure to port (see MIM 271). additional symptoms. Use the machine / ' halt as your symptom. No more than 25 seconds after RESTART is Go to Step 183, Entry Point K. pressed, the following events should occur: 1. ABCDEFGH appears on the top line of the 182 5110 display. Use the probe as a failure indicator. A bad 2. ABCDEFGHJKLMNP appears on the top line. condition is indicated by a· DOWN light. 3. The top line is Cleared and either LOADO or Go to Step 183, Entry Point K. CLEAR WS appears once on one and only one line of the 5110 display. 183 (Entry Point K) -Press RESTART. The maximum number of I/O devices that can be Do all three events shown above occur in attached to the 5110 is three. If a 5103 is sequence after RESTART is pressed? attached, it must be the last I/O device in the Y N string of I/O devices, because it terminates all the I/O signal lines. If a 5103 is not attached, 178 the last I/O device must have a cable terminator Go to Page 1, Step 002, Entry Point J. attached. If a 5106 is attached, it must be the first I/O device attached to the 5110. 179 A 5106 can only be attached if the 5110 has an One of the devices is suspect. internal tape unit.

- Connect all of the devices to the 5110 I/O Is a 5106 attached to the 51107 interface port. Y N -Press RESTART. Wait 25 seconds. 184 Is the machine at halt A, C, E, H, J OR Q? Are there two 5114's attached to the 5110? (See BRINGUP HALTS in the Diagnostic Aids Y N section of the MIM.) Y N 185 Is there one 5114 attached to the 5110? 180 Y N Determine if the POR reset line is bad. 186 -Probe H2-B03 (-POR reset). Bad printer B 1A2 (adapter) card (see MAP 050 for jumpering). Is the DOWN light on? Bad A2 (I/O cable driver) card and cable Y N assembly in 5110. Check/replace the 5103 I/O interface / cable (see MAP 0210 and MIM 280).

01JAN79 111 977 EC 836600 PEC 835541 B B B B B B M N P Q R S MAP 0400-16 B BRING UP MAP B B MAP 0400-17 S R T 1 1 6 6 PAGE 17 OF 23

187 191 Is a 5103 attached to the 5114? Bad 5114 C1 (adapter) card (see MAP 050 Y N before replacing this card). . (- Check/replace the 5114 internal cables 01 188 and 03 (see 280 and MAP 0210). Bad 5114 C 1 (adapter) card (see MAP 050 Check/replace the 5114 I/O interface cable before replacing this card). (see 280 and MAP 0210). Bad A2 (I/O cable driver) card and cable assembly in 5110. 192 Check/replace the 5114 internal cables 01 (Entry Point I) and 03 (see 280 and MAP 0210). Check/replace the 5114 I/O interface cable The first 5114 in the string of I/O devices (see 280 and MAP 0210). attached to the 5110 will be called 5114-1. The Bad cable terminator. second 5114 will be called 5114-2.

189 -Diconnect 5114-1 from the 5110 I/O interface -Disconnect the 5114 from the 5110. port. -Connect the 5103 to the 5110. -Connect 5114-2 to the 5110. • No more than 25 seconds after RESTART is No more than 25 seconds after RESTART is pressed, the following events should occur: pressed, the following events should occur: 1. ABCDEFGH appears on the top line of the 1. ABCDEFGH appears on the top line of the

., 5110 display. 5110 display. """"." 2. ABCDEFGHJKLMNP appears on the top line, 2. ABCDEFGHJKLMNP appears on the top line. C 3. The top line is cleared and either LOADO or 3. The top line is cleared and either LOADO or CLEAR WS appears once on one and only CLEAR WS appears once on one and only one line of the 5110 display. one line of the 5110 display.

-Press RESTART. -Press RESTART.

Do all three events shown above occur in Do all three events shown above occur in sequence after RESTART is pressed? sequence after RESTART is pressed? Y N Y N

190 193 Bad printer B 1A2 (adapter) card (see MAP Is a 5103 attached? 050 for jumpering). Y N Bad A2 (I/O cable driver) card and cable assembly in 5110. Check/replace the 5103 I/O interface cable (see MAP 0210 and MIM 280).

01JAN79 111 988 EC 836600 PEC 835541 B B B B T U V W MAP 0400-17 B BRING UP MAP B B MAP 0400-18 W V X 1 1 7 7 PAGE 18 OF 23

194 198 -Disconnect 5114-2 from the 5110. The trouble is in 5114-2. -Connect 5114-1 to the 5110. -Connect the cable terminator to 5114-1. Check/replace the 5114 internal cables D1 No more than 25 seconds after RESTART is and D3 (see 280 and MAP 0210). ~, ) pressed, the following events should occur: Check/replace the 5114 I/O interface cable 1. ABCDEFGH appears on the top line of the (see 280 and MAP 0210). 5110 display. 2. ABCDEFGHJKLMNP appears on the top line. 199 3. The top line is cleared and either LOADO or -Disconnect 5114-2 from the 5110. CLEAR WS appears once on one and only -Connect the 5103 to the 5110. one line of the 5110 display. No more than 25 seconds after RESTART is pressed, the following events should occur: -Press RESTART. 1. ABCDEFGH appears on the top line of the 5110 display. Do all three events shown above occur in 2. ABCDEFGHJKLMNP appears on the top line. sequence after RESTART is pressed? 3. The top line is cleared and either LOADO or Y N CLEAR WS appears once on one and only one line of the 5110 display. 195 Bad A2 (I/O cable driver) card and cable -Press RESTART. assembly in 5110. Bad cable terminator. Do all three events shown abOVE) occur in sequence after RESTART is pressed? 196 Y N -Remove the C1 cards from 5114-1 and 5114-2. -Install the card from 5114-2 into 5114-1. 200 No more than 25 seconds after RESTART is Bad printer B 1A2 (adapter) card (see MAP pressed, the following events should occur: 050 for jumpering). 1. ABCDEFGH appears on the top line of the Bad A2 (I/O cable driver) card and cable 5110 display. assembly in 5110. 2. ABCDEFGHJKLMNP appears on the top line. Check/replace the 5103 I/O interface cable 3. The top line is cleared and either LOADO or (see MAP 0210 and MIM 280). CLEAR WS appears once on one and only one line of the 5110 display. 201 The trouble is in 5114-2. -Press RESTART. Bad 5114 C1 (adapter) card (see MAP 050 before Do all three events shown above occur in replacing this card). sequence after RESTART is pressed? Check/replace the 5114 internal cables D1 and Y N D3 (see 280 and MAP 0210). Check/replace the 5114 I/O interface cable (see 197 280 and MAP 0210). The bad C1 card is now in 5114-1. '<.

01JAN79

EC 836600 PEC 835541 B X MAP 0400-18 B B BRING UP MAP B C MAP 0400-19 ~ ~ Z A (" 6 7 PAGE 19 OF 23

202 207 -Remove the C1 cards from 5114-1 and Bad 5106 C1 (adapter) card (see MAP 050 for 5114-2. jumpering). -Install the card from 5114-1 into 5114-2. Bad A2 (I/O cable driver) card and cable No more than 25 seconds after RESTART is assembly in 5110. pressed, the following events should occur: Check/replace the 5106 internal cables B1 1. ABCDEFGH appears on the top line of the and B2 (see MAP 0210 and MIM 280). 5110 display. Check/replace the 5106 I/O interface cable 2. ABCDEFGHJKLMNP appears on the top (see MAP 0210 and MIM 280). {,,' line. 3. The top line is cleared and either LOADO 208 or CLEAR WS appears once on one and - Remove the tape control cards from the internal only one line of the 5110 display. tape unit and from the 5106. -Install the card from the internal tape unit into -Press RESTART. the 5106. No more than 25 seconds after RESTART is I Do all three events shown above occur in pressed, the following events should occur: sequence after RESTART is pressed? 1. ABCDEFGH appears on the top line of the Y N 5110 display. 2. ABCDEFGHJKLMNP appears on the top line. 203 3. The top line is cleared and either LOADO or The bad C1 card is now in 5114-2. CLEAR WS appears once on one and only ( "" one line of the 5110 display. ,./ 204 The trouble is in 5114-1. - Press RESTART.

Check/replace the 5114 internal cables D1 Do all three events shown above occur in and D3 (see 280 and MAP 0210). sequence after RESTART is pressed? Check/ replace the 5114 I/O interface cable Y N (see 280 and MAP 0210). 209 205 -Swap the tape control cards back to their Is a 5114 attached to the 5106? original locations. Y N -Disconnect the 5106 from the 5110 I/O interface port. 206 -Connect the 5103 to the 5110. Is a 5103 attached? No more than 25 seconds after RESTART is c· Y N pressed, the following events should occur: 1. ABCDEFGH appears on the top line of the 5110 display. 2. ABCDEFGHJKLMNP appears on the top line. 3. The top line is cleared and either LOADO c or CLEAR WS appears once on one and only one line of the 5110 display.

(Step 209 continues)

01JAN79 2 2 o o EC 836600 PEC 835541 B B C C Y Z A B MAP 0400-19 B C BRING UP MAP C MAP 0400-20 Y B D 1 1 9 9 PAGE 20 OF 23

(Step 209 continued) -Press RESTART. 214 -Swap the tape control cards back to their Do all three events shown above occur original locations. in sequence after RESTART is pressed? - Disconnect the 5106 from the 5110 I/O Y N interface port. -Connect the 5114 to the 5110. 210 No more than 25 seconds after RESTART is Bad printer B 1A2 (adapter) card (see pressed, the following events should occur: MAP 050 for jumpering). 1. ABCOEFGH appears on the top line of the Bad A2 (I/O cable driver) card and cable 5110 display. assembly in 5110. 2. ABCOEFGHJKLMNP appears on the top line. Check/replace the 5103 I/O interface 3. The top line is cleared and either LOADO or cable (see MAP 0210 and MIM 280). CLEAR WS appears once on one and only one line of the 5110 display. 211 Bad 5106 C 1 (adapter) card (see MAP 050 -Press RESTART. for jumpering). Check/replace the 5106 internal cables Bl Do all three events shown above occur in and B2 (see MAP 0210 and MIM 280). sequence after RESTART is pressed? Check/replace the 5106 I/O interface Y N cable (see MAP 0210 and MIM 280). 215 212 Is a 5103 attached? The tape control card you removed from the Y N 5106 is bad. 216 213 Bad 5114 Cl (adapter) card (see MAP 050 - Remove the tape control cards from the internal before replacing this card). tape unit and the 5106. Bad A2 (I/O cable driver) card and cable -Install the card from the internal tape unit into assembly in 5110. the 5106. Check/replace the 5114 internal cables 01 No more than 25 seconds after RESTART is and 03 (see 280 and MAP 0210). pressed, the following events should occur: Check/replace the 5114 I/O interface 1. ABCDEFGH appears on the top line of the cable (see 280 and MAP 0210). 5110 display. Bad cable terminator. 2. ABCDEFGHJKLMNP appears on the top line. 3. The top line is cleared and either LOAOO or CLEAR WS appears once on one and only one line of the 5110 display.

-Press RESTART.

Do all three events shown above occur in sequence after RESTART is pressed?

IN 01JAN79 2 2 2 1 1 1 EC 836600 PEC 835541 \~. ,~. C C C C C 0 E F MAP 0400-20 c C BRING UP MAP c MAP 0400-21 E F C 2 2 2 o 0 o PAGE 21 OF 23

217 221 -Disconnect the 5114 from the 5110 I/O The tape control card you removed from the interface port. 5106 is bad. ("" -Connect the 5103 to the 5110. No more than 25 seconds after RESTART is pressed, the following events should occur: 1. ABCDEFGH appears on the top line of the 5110 display. 2. ABCDEFGHJKLMNP appears on the top line. 3. The top line is cleared and either LOADO or CLEAR WS appears once on one and only one line of the 5110 display. -Press RESTART. I Do all three events shown above occur in sequence after RESTART is pressed? Y N

218 Bad printer B 1A2 (adapter) card (see MAP 050 for jumpering). Bad A2 (I/O cable driver) card and cable assembly in 5110. Check/replace the 5103 I/O interface cable (see MAP 0210 and MIM 280).

219 Bad 5114 C1 (adapter) card (see MAP 050 before replacing this card). Check/replace the 5114 internal cables D1 and D3 (see 280 and MAP 0210). Check/replace the 5114 I/O interface cable (see 280 and MAP 0210).

220 Bad 5106 C1 (adapter) card (see MAP 050 for jumpering). Check/replace the 5106 internal cables B1 and B2 (see MAP 0210 and MIM 280). Check/replace the 5106 I/O interface cable (see c MAP 0210 and MIM 280).

01JAN79

EC 836600 PEC 835541

MAP 0400-21 BRING UP MAP MAP 0400-22

PAGE 22 OF 23

(Step 225 continued) 222 (Entry Point G) Do all three events shown above occur in sequence after Power Up? Is there a card in K41 Y N Y N 226 223 -Power down. (Entry Point Q) -Rmove M2. -Istall he ard hat as n M4 into the M2 location. Now determine if read/write storage is No more than 25 seconds after power up, the functioning. following events should occur: 1. ABCDEFGH appears on the top line of the Are there cards installed in M4, or N2, or 5110 display. N4 (read/write storage)? 2. ABCDEFGHJKLMNP appears on the top Y N line. 3. The top line is cleared and either LOADO 224 or CLEAR WS appears once on one and Bad M2 (read/write storage) card. only one line of the display. Bad J2 (processor) card (see MAP 050 for jumpering). -Power up. Bad G2 (display) card (see MAP 050 for jumpering). Do all three events shown above occur in Bad H2 (base I/O) card. sequence after Power Up? Bad L2 (exec ROS) card (see MAP 050 for Y N jumpering). Bad F2 (Common and language ROS) card. 227 Bad J2 (processor) card (see MAP 050 for 225 jumpering). - Power down. Bad G2 (display) card (see MAP 050 for - Remove the cards in M4, N2, and N4 if jumpering). installed. Bad H2 (base I/O) card. No more than 25 seconds after power up, the Bad L2 (exec ROS) card (see MAP 050 for following events should occur: jumpering). 1. ABCDEFGH appears on the top line of the Bad F2 (Common and language ROS) card. 5110 display. 2. ABCDEFGHJKLMNP appears on the top 228 line. The card that was in M2 is bad. \, 3. The top line is cleared and either LOADO or CLEAR WS appears once on one and only one line of the display.

-Power up. (Step 225 continues)

01JAN79 2 2 3 3 EC 836600 PEC 835541 C C G H MAP 0400-22 c C BRING UP MAP MAP 0400-23 G H 2 2 2 2 PAGE 23 OF 23

229 One of the read/write storage cards you removed is suspect. Install the cards one at a time, powering down before each replacement and powering up after each card is installed. Use the preceeding step to determine which card is bad.

If machine still fails: Bad J2 (processor) card (see MAP 050 for jumpering).

230 - Remove the K4 card. -Press RESTART. Wait 25 seconds.

Did either LOADO or CLEAR WS (spelled I correctly) appear only once on one and only one line of the 5110 display? V N

231 Go to Page 22, Step 223. Entry Point Q.

232 Bad K4 (ROS feature) card (see MAP 050 for jumpering).

' 01JAN79 C~v' EC 836600 PEC 835541 MAP 0400-23 /-) ~l,. ", '

"'l,l1'

This page intentionally left blank.

MAP 0400-24 PROCESS CHECK MAP 0420 MAP 0420-1

("- \ PAGE 1 OF 26

ENTRY POINTS EXIT POINTS FROM ENTER THIS MAP EXIT THIS MAP TO ( It MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT

0200 A 001 5 046 0400 A 0300 A 001 19 220 0400 A

('~- ' 0310 A 001 26 292 0500 A 0600 A 001 0810 A 001 0830 A 001 0850 A 001 0900 A 001

001 (Entry Point A)

Is the PROCESS CHECK light on? V N

002 Can you create the PROCESS CHECK? Y N

003 The MAPs depend on having the PROCESS CHECK on the machine or being able to create the PROCESS CHECK. Gather and record all available information pertaining to the PROCESS CHECK. Advise the customer that if the PROCESS CHECK appears again, to leave the machine in the failing condition until you arrive.

004 Is the PROCESS CHECK intermittent? V N c

© Copyright IBM Corp. 1979 01JAN79 CI EC 836600 PEC 835541 222 ABC MAP 0420-1 ABC PROCESS CHECK MAP G MAP 0420-2 111

PAGE 2 OF 26

005 012 Create the PROCESS CHECK. (Entry Point M)

Did the PROCESS CHECK come on as a Is there a card in A2 or 82 or 02 or K2 or K4 result of pressing RESTART or powering (see MIM 209)? on the 5110? Y N Y N 013 006 (Entry Point D) We will assume that the PROCESS CHECK comes on as a result of running Machine check is -caused by an RDR error, a a job. DA error, a KBD error, a BUS IN error or a Go to Step 010, BUS OUT error. The RDR and BUS IN errors Entry Point H. can be probed on the J2 card. The KBD error can be probed on the H2 card. The DA and 007 BUS OUT errors can be probed only at the We will use the RESTART condition to device. create the PROCESS CHECK. -Switch the DISPLAY REGISTERS switch to Go to Step 010, Entry Point H. NORMAL. -Probe H2-U13 (+KBD parity check). 008 (See appendix B, the general logic probe, in Create the PROCESS CHECK. the 5110 MIM). Go to the INTERMITTENT FAILURE CHART in the 5110 SERVICE AIDS. Is the UP light on? Y N 009 Is the PROCESS CHECK intermittent? 014 Y N -Probe J2-U09 (-BUS IN check).

010 Is the DOWN light on? (Entry Point H) Y N

-Switch the DISPLAY REGISTERS switch to 015 DISPLAY REGISTERS. -Probe J2-S08 (-RDR Check). -Switch the RUN switch under the covers to RUN. Is the DOWN light on or pulsing? Y N Is the display blank or dark? Y N 016 - Probe H2-M02 (+DA check). 011 Are there any devices attached to the Is the UP light on? 5110 I/O interface port (see MIM 271)? Y N Y N

01JAN79 2 2 1 1 1 1 EC 836600 PEC 835541 668 88466 3 o E F G H J K L M N MAP 0420-2 N PROCESS CHECK MAP T MAP 0420-3 2

PAGE 3 OF 26

017 023 - Probe H2-P07 (+BUS OUT check). The bus out line probe points in the preceeding step are to be used as the probe points in the (''''"~ Is the UP light on1 next several steps. . . - Y N Are an even number (or none) of the probe 018 points DOWN? -Probe F2-U13 (+DA check) and F2-U11 Y N (+BUS OUT check). 024 Is the DOWN light on for both probe -Switch the RUN switch under the covers to points? NOT RUN. Y N - Remove the F2 card.

019 Did any of the probe points change 7 -Probe F2-U13. Y N

Is the UP light on? 025 Y N -Reinstall the F2 card. -Remove the G2 card. 020 -Probe F2-U11. Did any of the probe points change 7 Y N c Is the UP light on? Y N 026 - Reinstall the G2 card. 021 -Switch the RUN switch under the Bad F2 (Common and language ROS) covers to RUN. card. Bad H2 (base I/O) card. 022 Bad J2 (processor) card (see MAP 050 (Entry Point P) for jumpering). Bad L2 (exec ROS) card (see MAP 050 -Probe the bus out lines below. Record for jumpering). the results. 027 H2-G05 1 H2-J09 0 Bad G2 (display) card (see MAP 050 for H2-G09 5 H2-Jl0 3 jumpering). H2-Gl0 4 H2-M04 p H2-G12 7 H2-B13 6 028 H2-J05 2 -Switch the RUN switch under the covers to RUN. Are both lights off for any of the c probe points? Bad F2 (Common and language ROS) card. Y N Bad J2 (processor) card (see MAP 050 for jumpering).

01JAN79 c' EC 836600 PEC 835541 544 4 4 P Q R S T U MAP 0420-3 o R S U PROCESS CHECK MAP v wX y MAP 0420-4 3 3 3 3

PAGE 4 OF 26

029 037 - Remove the G2 card. Bad F2 (Common and language ROS) -Press RESTART. Wait 25 seconds. card.

Is the PROCESS CHECK light on1 038 Y N Go to Page 3, Step 022, Entry Point P.

030 039 Bad G2 (display) card (see MAP 050 Go to Page 14, Step 160, Entry Point G. for jumpering). 040 031 -Probe L2-D05 (-POR switch). Bad L2 (exec ROS) card (see MAP 050 for jumpering). Is the DOWN light on 1 Bad F2 (Common and language ROS) Y N card. Bad H2 (base I/O) card. 041 -Probe H2-G06 (-machine check). 032 -Switch the RUN switch under the covers Is the DOWN light on 1 to RUN. Y N

Bad H2 (base I/O) card. 042 Bad L2 (exec ROS) card (see MAP 050 for 033 jumpering). Go to Page 14, Step 160, Entry Point G. Bad J2 (processor) card (see MAP 050 for jumpering). 034 Bad G2 (display) card (see MAP 050 for -Probe G2-M09 (+DA check) and G2-M05 (+bus jumpering). out check). Bad H2 (base I/O) card. Check/ replace Z3 (display and control Is the DOWN light on for both probe points 1 panel) cable (see MAP 0210 and MIM Y N 248,249).

035 043 -Probe G2-M09. - Remove the F2 card. -Press RESTART. Wait 25 seconds. Is the UP light on1 -Probe H2-G06. Y N Is the DOWN light on 1 036 Y N -Probe G2-M05. 044 Is the UP light on 1 Bad F2 (Common and language ROS) card. Y N

01JAN79

5 EC 836600 PEe 835541 5 A v wX y Z A MAP 0420-4 Z A PROCESS CHECK MAP P MAP 0420-5 4 A 3 4 PAGE 5 OF 26

045 051 -Install the F2 card. (Entry Point E) -Press RESTART. Wait 25 seconds. - Power down. Is the PROCESS CHECK light on? -Remove read/write storage cards M2, M4, N2, Y N and N4, if installed. -Switch the DISPLAY REGISTERS switch to 046 DISPLAY REGISTERS. Go To Map 0400, Entry Point A. (See DISPLAY REGISTERS in the Diagnostic Aids section in the MIM). 047 -Power up. Wait 25 seconds. Bad L2 (exec ROS) card (see MAP 050 for jumpering). Does R7LO contain FFFF? Bad G2 (display) card (see MAP 050 for Y N jumpering). Bad H2 (base I/O) card. 052 Bad J2 (processor) card (see MAP 050 for Bad J2 (processor) card (see MAP 050 for jumpering). jumpering). Bad G2 (display) card (see MAP 050 for 048 jumpering). -Remove the F2, L2, and G2 cards. Bad H2 (base I/O) card. - Probe L2 - D05. Bad L2 (exec ROS) card (see MAP 050 for jumpering). c:' Is the DOWN light on 7 Bad F2 (Common and language ROS) card. Y N 053 049 One of the cards removed is suspect. Reinstall One of the cards removed is suspect. them one at a time (M2 first, then M4, N2, and Reinstall F2, L2, and G2 one at a time. The N4), powering down before and powering up card which causes the probe DOWN light to after each card, to isolate the bad card. turn on is bad. If a failure still exists; 050 Bad J2 (processor) card (see MAP 050 for Bad RESTART switch. jumpering). Check/ replace Z3 (display and control panel) Bad H2 (base I/O) card. cable (see MAP 0210 and MIM 248,249). Bad G2 (display) card (see MAP 050 for jumpering). Bad L2 (exec ROS) card (see MAP 050 for jumpering). Bad F2 (Common and language ROS) card. c

01JAN79 c EC 836600 PEe 835541 MAP 0420-5 L M PROCESS CHECK MAP A MAP 0420-6 2 2 E

PAGE 6 OF 26

054 060 Bad J2 (processorl card (see MAP 050 for - Remove the G2 card. jumpering). -Press RESTART. Wait 25 seconds. Bad H2 (base I/O) card. Bad G2 (display) card (see MAP 050 for Is the PROCESS CHECK light on? \, " jumpering). Y N

055 061 -Press RESTART. Wait 25 seconds. Bad G2 (display) card (see MAP 050 for - Perform the failing job, if possible. jumpering).

Is the PROCESS CHECK light on? 062 Y N -Install the G2 card. -Press RESTART. Wait 25 seconds. 056 -Switch the DISPLAY REGISTERS switch to A~e both the PROCESS CHECK light and DISPLAY REGISTERS. the IN PROCESS light on while the RESTART switch is pressed? Does R7LO contain FFFF? Y N (See DISPLAY REGISTERS in the Diagnostic Aids section in the MIM). 057 Y N Bad I N PROCESS light. Bad RESTART switch. 063 Check/ replace Z3 (display and control Go to Page 5, Step 051, Entry Point E. panel) cable (see MAP 0210 and MIM 248,249). 064 Are there any cards in M4, N2, or N4? 058 Y N -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. 065 -Record RFLO. Bad M2 (read/write storage) card. (See DISPLAY REGISTERS in the Diagnostic Bad H2 (base I/O) card. Aids section in the MIM). Bad J2 (processor) card (see MAP 050 for -Switch the DISPLAY REGISTERS switch to jumpering). NORMAL. 066 Is the machine at halt H? -Power down. (See BRINGUP HALTS in the Diagnostic -Remove the read/write storage cards from M4, Aids section of the MIM.) N2, and N4 if installed. Y N - Power up. Wait 25 seconds.

059 Did either LOADO or CLEAR WS (spelled Did the machine pass halt A? (If you do correctly) appear only once on one and only not know, take the N column). one line of the 5110 display? Y N Y N

01JAN79 1 377 7 7 EC 836600 PEC 835541 A A A A A A BCD E F G MAP 0420-6 A A A A PROCESS CHECK MAP A MAP 0420-7 C 0 F G K 6 6 6 6

PAGE 7 OF 26

067 074 -Power down. Is there a card in M4? -Remove the M2 card. V N -Install one of the other read/write storage cards into the M2 location. 075 - Power up. Wait 25 seconds. Is the recorded RFLO between or including 0000 and 3FFF? Did either LOADO or CLEAR WS Y N (spelled correctly) appear only once ("'" on one and only one line of the 5110 076 display? Bad J2 (processor) card (see MAP 050 for Y N jumpering). Bad H2 (base I/O) card. 068 Bad L2 (exec ROS) card (see MAP 050 for Bad H2 (base I/O) card. jumpering). Bad J2 (processor) card (see MAP Bad G2 (display) card (see MAP 050 for 050 for jumpering). jumpering).

069 077 The card that was in M2 is bad. Bad M2 (read/write storage) card. Bad J2 (processor) card (see MAP 050 for 070 jumpering). One of the read/write storage card Bad L2 (exec ROS) card (see MAP 050 for removed is bad. jumpering). Reinstall them one at a time (M4 first, then Bad H2 (base I/O) card. N2, N4), powering down before and Bad G2 (display) card (see MAP 050 for powering up after each card is replaced. jumpering). The card that causes a PROCESS CHECK, is bad. 078 Is the recorded RFLO between or including 071 0000 and 3FFF? Bad L2 (exec ROS) card (see MAP 050 for V N jumpering). Bad J2 (processor) card (see MAP 050 for 079 jumpering). Is the recorded RFLO between or including Bad H2 (base I/O) card. 4000 and 7FFF7 Y N 072 Is there a card in N4? 080 V N Bad J2 (processor) card (see MAP 050 for jumpering). 073 Bad L2 (exec ROS) card (see MAP 050 for IS there a card in N2? jumpering). c V N Bad H2 (base I/O) card. Bad G2 (display) card (see MAP 050 for jumpering).

01JAN79 1 o 8 8 8 EC 836600. PEC 835541 c' A A A A A H J K L M MAP 0420-7 A PROCESS CHECK MAP A A MAP 0420-8 M J L 7 7 7 PAGE 8 OF 26

081 088 - Power down. - Power down. - Exchange M2 with M4. -Exchange M2 with M4. - Power up. Wait 25 seconds. - Power up. Wait 25 seconds.

Did either LOA DO or CLEAR WS (spelled Did either LOADO or CLEAR WS (spelled correctly) appear only once on one and only correctly) appear only once on one and one line of the 5110 display? only one line of the 5110 display? Y N Y N

082 089 Is the machine at halt H? -Switch the DISPLAY REGISTERS switch Y N to DISPLAY REGISTERS. - Record RFLO. 083 (See DISPLAY REGISTERS in the Bad read/write storage card is now at M2. Diagnostic Aids section in the MIM). -Switch the DISPLAY REGISTERS switch 084 to NORMAL. -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. Is RFLO between or including 0000 and -Record RFLO. 3FFF? (See DISPLAY REGISTERS in the Diagnostic Y N Aids section in the MIM). -Switch the DISPLAY REGISTERS switch to 090 NORMAL. Bad read/write storage card is now at M4. Is RFLO between or including 0000 and 3FFF? 091 Y N Bad J2 (processor) card (see MAP 050 for jumpering). 085 Bad L2 (exec ROS) card (see MAP 050 for Bad J2 (processor) card (see MAP 050 for jumpering). jumpering). Bad H2 (base I/O) card. Bad L2 (exec ROS) card (see MAP 050 for Bad G2 (display) card (see MAP 050 for jumpering). jumpering). Bad H2 (base I/O) card. Bad G2 (display) card (see MAp· 050 for 092 jumpering). The trouble probably was a bad card connection. 086 Bad read/write storage card is now at M2. 093 Is the recorded RFLO between or including 087 0000 and 3FFF? The trouble probably was a bad card connection. Y N

01JAN79 1 o 9 EC 836600 PEC 835541 A A N P MAP 0420-8 A PROCESS CHECK MAP A A A A MAP 0420-9 p Q R S T 8

PAGE 9 OF 26

094 099 Is the recorded RFLO between or including Bad J2 (processor) card (see MAP 050 4000 and 7FFF? for jumpering). Y N Bad L2 (exec ROS) card (see MAP 050 for jumpering). 095 Bad H2 (base I/O) card. Is the recorded RFLO between or including Bad G2 (display) card (see MAP 050 for 8000 and BFFF? jumpering). Y N 100 096 Bad read/write storage card is now at M4. Bad J2 (processor) card (see MAP 050 for jumpering). 101 Bad L2 (exec ROS) card (see MAP 050 for The trouble probably was a bad card jumpering). connection. Bad H2 (base I/O) card. Bad G2 (display) card (see MAP 050 for 102 jumpering). -Power down. -Exchange M2 with M4. 097 - Power up. Wait 25 seconds. - Power down. - Exchange M4 with N2. Did either lOADO or CLEAR WS (spelled - Power up. Wait 25 seconds. correctly) appear only once on one and only one line of the 5110 display? Did either LOADO or CLEAR WS (spelled Y N correctly) appear only once on one and only one line of the 5110 display? 103 Y N Is the machine at halt H? 098 Y N -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. 104 -Record RFLO. Bad read/write storage card is now at M2. (See DISPLAY REGISTERS in the Diagnostic Aids section in the MIM). 105 -Switch the DISPLAY REGISTERS switch -Switch the DISPLAY REGISTERS switch to to NORMAL. DISPLAY REGISTERS.

Is RFlO between or including 4000 and Is RFlO· between or including 0000 and 7FFF? 3FFF? c Y N Y N

01JAN79 111 000 EC 836600 PEC 835541 A A A A A A A Q R S T U V W MAP 0420-9

.",.0 .. ,••• n , ....., .... ",~., "... "'~" I, ".... , .. ,., "'.,,' "",'m,. '"""n '" n, ..... " ••, .. ,\4f~, , .., .."", ....11, ...... , .. "' ••• "._., •• ",.,n "., ,...... _ .• _~~,_ •. y_ ". A A A A PROCESS CHECK MAP A A A MAP 0420-10 N U V W H X Y 899 9 7 PAGE 10 OF 26

106 112 Bad L2 (exec ROS) card (see MAP 050 -Switch the DISPLAY REGISTERS switch for jumpering). to DISPLAY REGISTERS. Bad J2 (processor) card (see MAP 050 for jumpering). Is RFLO equal to a value from 4000 to Bad H2 (base I/O) card. 7FFF? Bad G2 (display) card (see MAP 050 for Y N jumpering). 113 107 Bad L2 (exec ROS) card (see MAP 050 Bad read/write storage card is now at M2. for jumpering). Bad G2 (display) card (see MAP 050 for 108 jumpering). The trouble probably was a bad card Bad H2 (base I/O) card. connection. Bad J2 (processor) card (see MAP 050 for jumpering). 109 - Power down. 114 -Exchange M2 with M4. Bad read/write storage card is now at M4. - Power up. Wait 25 seconds. 115 Did either LOADO or CLEAR WS (spelled The trouble probably was a bad card correctly) appear only once on one and only connection. one line of the 5110 display? Y N 116 Is the recorded RFLO between or including 110 0000 and 3FFF? Y N Is the machine at halt H? Y N 117 Is the recorded RFLO between or including 111 4000 and 7FFF? Bad G2 (display) card (see MAP 050 for Y N jumpering). Bad J2 (processor) card (see MAP 050 for 118 jumpering). Bad H2 (base I/O) card. Is the recorded RFLO between or 1 Bad L2 (exec ROS) card (see MAP 050 for including SOOO and BFFF? jumpering). Y N

01JAN79 1 1 1 1 2 2 1 1 EC 836600 PEC 835541 A A A B B B X y Z ABC MAP 0420-10 B PROCESS CHECK MAP B MAP 0420-11 C B o1 o1 PAGE 11 OF 26

119 124 -Power down. - Power down. - Exchange N4 with M4. -Exchange M4 with N2. ( "._, .... \ - Power up. Wait 25 seconds. - Power up. Wait 25 seconds. - y Did either LOADO or CLEAR WS (spelled Did either LOADO or CLEAR WS (spelled correctly) appear only once on one and only correctly) appear only once on one and only one line of the 5110 display? one line of the 5110 display? V N V N

120 125 -Switch the DISPLAY REGISTERS switch to -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. DISPLAY REGISTERS. - Record RFLO. -Record RFLO. (See DISPLAY REGISTERS in the Diagnostic (See DISPLAY REGISTERS in the Diagnostic Aids section in the MIM). Aids section in the MIM). -Switch the DISPLAY REGISTERS switch to -Switch the DISPLAY REGISTERS switch to NORMAL. NORMAL.

Is RFLO between or including 4000 and Is the RFLO between or including 4000 and 7FFF? 7FFF? V N V N

121 126 Bad J2 (processor) card (see MAP 050 for Bad J2 (processor) card (see MAP 050 for jumpering). jumpering). Bad H2 (base I/O) card. Bad L2 (exec ROS) card (see MAP 050 for Bad L2 (exec ROS) card (see MAP 050 for jumpering). jumpering). Bad H2 (base I/O) card. Bad G2 (display) card (see MAP 050 for 122 jumpering). Bad read / write storage card is now at M4. 127 123 Bad read/write storage card is now at M4. The trouble probably was a bad cable connection. 128 The trouble probably was a bad card connection.

01JAN79 c EC 836600 PEC 835541 MAP 0420-11 B PROCESS CHECK MAP A B B MAP 0420-12 A ZOE o1 o1 PAGE 12 OF 26

129 134 -Power down. Bad read/write storage card is now in N2. -Exchange N2 with M4. -Power up. Wait 25 seconds. 135 The trouble probably was a bad card J. Did either LOADO or CLEAR WS (spelled connection. correctly) appear only once on one and only one line of the 5110display7 136 Y N -Power down. -Exchange M2 with N2. 130 - Power up. Wait 25 seconds. Is the machine at halt H7 Y N Did either LOADO or CLEAR WS (spelled correctly) appear only once on one and only 131 one line of the 5110 display? Bad G2 (display) card (see MAP 050 for Y N jumpering). Bad J2 (processor) card (see MAP 050 for 137 jumpering). Bad H2 (base I/O) card. Is the machine at halt H? Bad L2 (exec ROS) card (see MAP 050 for Y N jumpering). 138 132 Bad J2 (processor) card (see MAP 050 for -Switch the DISPLAY REGISTERS switch to jumpering). DISPLAY REGISTERS. Bad H2 (base I/O) card. - Record RFLO. Bad L2 (exec ROS) card (see MAP 050 for (See DISPLAY REGISTERS in the Diagnostic jumpering). Aids section in the MIM). -Switch the DISPLAY REGISTERS switch to 139 NORMAL. -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. Is RFLO between or including 8000 and -Record RFLO. BFFF? (See DISPLAY REGISTERS in the Diagnostic Y N Aids section in the MIM). -Switch the DISPLAY REGISTERS switch to 133 NORMAL. Bad J2 (processor) card (see MAP 050 for jumpering). Is RFLO between or including 8000 and Bad L2 (exec ROS) card (see MAP 050 for BFFF? jumpering). V N Bad H2 (base I/O) card. Bad G2 (display) card (see MAP 050 for jumpering).

01JAN79 111 333 EC 836600 PEC 835541 B B B B B o E F G H MAP 0420-12 A B B B PROCESS CHECK MAP B B B B MAP 0420-13 B F G H J K L M 6 1 1 1 222 PAGE 13 OF 26

140 148 " '" Bad J2 (processor) card (see MAP 050 Bad L2 (exec ROS) card (see MAP 050 ( for jumpering). for jumpering). Bad L2 (exec ROS) card (see MAP 050 Bad G2 (display) card (see MAP 050 for for jumpering). jumpering). Bad H2 (base I/O) card. Bad J2 (processor) card (see MAP 050 Bad G2 (display) card (see MAP 050 for for jumpering). jumpering). Bad H2 (base I/O) card.

141 149 Bad read/write storage card is now in N2. Bad N4 (read/write storage) card. Bad L2 (exec ROS) card (see MAP 050 for 142 jumpering). The trouble probably was a bad card Bad J2 (processor) card (see MAP 050 for connection. jumpering). Bad H2 (base I/O) card. 143 -Switch the DISPLAY REGISTERS switch to 150 DISPLAY REGISTERS. Is there a card in N27 - Record the read / write storage size. Y N (See DISPLAY REGISTERS in the Diagnostic Aids section in the MIM). 151 Bad L2 (exec ROS) card (see MAP 050 for Does read/write storage size= 3FFF? jumpering). Y N Bad G2 (display) card (see MAP 050 for jumpering). 144 Bad J2 (processor) card (see MAP 050 for Does read/write storage size= 7FFF? jumpering). Y N Bad H2 (base I/O) card.

145 152 Does read/write storage size: BFFF? Bad N2 (read/write storage) card. Y N Bad L2 (exec ROS) card (see MAP 050 for jumpering). 146 Bad J2 (processor) card (see MAP 050 for Go to Page 5, Step 051, jumpering). Entry Point E. Bad H2 (base I/O) card.

147 153 Is there a card in N4? Is there a card in M4? Y N Y N

01JAN79 c' 1 1 4 4 EC 836600 PEC 835541 B B B B B B J K L M N P MAP 0420-13 K B B PROCESS CHECK MAP B MAP 0420-14 2 N P T 1 1 3 3 PAGE 14 OF 26

154 159 Bad L2 (exec ROS) card (see MAP 050 for Is ROLO between or including 0430 and 04BC? jumpering). Y N Bad G2 (display) card (see MAP 050 for jumpering). 160 Bad J2 (processor) card (see MAP 050 for (Entry Point G) jumpering). Bad H2 (base I/O) card. -Switch the RUN switch under the covers to RUN. 155 -Probe the device address lines and record Bad M4 (read/write storage) card. those that are UP. Bad L2 (exec ROS) card (see MAP 050 for jumpering). H2-B07 Xl H2-D07 XO Bad J2 (processor) card (see MAP 050 for H2-B09 YO H2-D09 X2 jumpering). H2-Bl0 Y2 H2-D10 Yl Bad H2 (base I/O) card. H2-D02 X3 H2-Dll Y3 Bad G2 (display) card (see MAP 050 for jumpering). Are exactly two of the lines UP? Y N 156 If the machine failed during the bring up test, the 161 halts should be visible on the display. Bad H2 (base I/O) card. (See BRINGUP HALTS in the Diagnostic Aids Bad J2 (processor) card (see MAP 050 for section of the MIM.) jumpering).

Is the machine at halt A? 162 Y N -Remove the G2 card. -Press RESTART. Wait 25 seconds. 157 - Perform the failing job, if possible. Is the machine at halt F? Y N Is the PROCESS CHECK light on? Y N 158 -Switch the RUN switch under the covers 163 to NOT RUN. Bad G2 (display) card (see MAP 050 for (See MIM 201). jumpering). -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. 164 Were B07 and B09 the two lines UP? Is ROLO less than 005E? Y N (See DISPLAY REGISTERS in the Diagnostic Aids section in the MIM). 165 Y N Were 007 and 010 the two lines UP? Y N

01JAN79 111 1 1 1 1 777 7 5 5 5 EC 836600 PEC 835541 B B B B B B B B Q R S T U V WX MAP 0420-14 B B B PROCESS CHECK MAP B MAP 0420-15 (~ V WX Z 111 444 PAGE 15 OF 26

166 173 Were 002 and 810 the two lines up? -Probe H2-U13 (+KBD parity check). Y N - Press the Z key.

167 Is the UP light on? Bad J2 (processor) card (see MAP 050 Y N for jumpering). Bad H2 (base I/O) card. 174 Bad L2 (exec ROS) card (see MAP 050 -Probe H2-U13 (+KBD parity check). for jumpering). -Press the W key. Bad F2 (Common and language ROS) card. Is the UP light on? Y N 168 Bad tape control card (see MIM 203). 175 -Probe H2-U13 (+KBD parity check). 169 - Hold the shift key and press the Z key. Bad F2 (Common and language ROS) card. Bad J2 (processor) card (see MAP 050 for Is the UP light on? jumpering). Y N Bad H2 (base I/O) card. 176 170 -Probe H2-U13 (+KBD parity check). (Entry Point C) - Press all the keys until the UP light comes on. Did the error occur while keying? - Using the key codes chart find the hex Y N value for the failing key (see MIM 250). The keycode is represented by bits at 171 an UP level. The keyboard generates a Bad H2 (base I/O) card. DOWN level parity bit if the unused Bad L2 (exec ROS) card (see MAP 050 for bits of the keycode, (down level bits), jumpering). are even. Bad J2 (processor) card (see MAP 050 for -Press and hold the failing key and jumpering). probe the KEYBOARD DATA BUS Bad keyboard PC board (see MIM 251). (note: DOWN is a 1, UP is a 0). Check/ replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255). H2-Jll 2 H2-M12 H2-M08 5 H2-P02 3 172 H2-M09 0 H2-P05 4 -Press RESTART. Wait 25 seconds. H2-Ml0 P H2-U02 6 -Probe H2-U13 (+KBD parity check). H2-Mll 7 -Press the 9 key on the alphameric keyboard. c Is the data on the bus correct? Is the UP light on? Y N Y N

I 01JAN79 1 11111 6 6 6 6 6 6 EC 836600 PEC 835541 B B C C C C C Y Z ABC D E MAP 0420-15 c c c C PROCESS CHECK MAP Bee MAP 0420-16 BCD E Y A F 111 1 1 1 5 5 5 5 5 5 PAGE 16 OF 26

177 186 Bad keyboard PC board (see MIM 251). Bad H2 (base I/O) card. Check/ replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255). 187 -Press and hold the Z key. 178 - Probe the keyboard data bus: Bad H2 (base I/O) card. H2-Jl1 2 H2-M12 1 H2-M08 5 H2-P02 3 179 H2-M09 0 H2-P05 4 - Press and hold the shift and the Z keys. H2-Ml0 P H2-U02 6 -Probe H2-M11 (-keyboard data bit 7). H2-Mll 7

Is the DOWN light on? Are bits 4 and 7 UP and all the rest Y N DOWN? Y N 180 Bad keyboard PC board (see MIM 251). 188 Check/ replace Z4 (keyboard) cable (see Bad H2 (base I/O) card. Map 0210 and MIM 206,255). Bad keyboard PC board (see MIM 251). Check/ replace Z4 (keyboard) cable (see 181 Map 0210 and MIM 206,255). Bad H2 (base I/O) card. 189 182 Bad H2 (base I/O) card. -Probe H2-M10 (-keyboard P bit). -Press and hold the W key. 190 - Press and hold the 9 key on the alphameric Is the UP light on? keyboard. Y N - Probe the keyboard data bus: H2-Jll 2 H2-M12 1 183 H2-M08 5 H2~P02 3 -Probe H2-M10. H2-M09 0 H2-P05 4 - Disconnect the keyboard cable at Z4. H2-Ml0 P H2-U02 6 H2-Mll 7 Is the UP light on? Y N Are all bits 0-7 UP and the P bit DOWN? Y N 184 Bad H2 (base I/O) card. 191 Are any bits neither UP nor DOWN? 185 Y N Bad keyboard PC board (see MIM 251). Check/replace Z4 (keyboard) cable (see Map 192 0210 and MIM 206,255). Any bit 0 through 7 DOWN? Y N II / 01JAN79 1 1 1 1 7 7 7 7 EC 836600 PEC 835541 C C C C C F G H J K MAP 0420-16 Bee C C PROCESS CHECK MAP B B B C MAP 0420-17 UGH J K o R S L 11111 T 1 1 4 6 6 6 6 444 PAGE 17 OF 26

193 201 Bad keyboard PC board (see MIM Bad J2 (processor) card (see MAP 050 251). for jumpering). Check/replace Z4 (keyboard) cable Bad L2 (exec ROS) card (see MAP 050 (see Map 0210 and MIM 206,255). for jumpering).

194 202 -Remove the Z4 (keyboard) cable. -Switch the RUN switch under the covers - Probe the keyboard data bus again: to RUN. c:' H2-Jll 2 H2-M12 1 H2-M08 5 H2-P02 3 Bad J2 (processor) card (see MAP 050 for H2-M09 0 H2-P05 4 jumpering). H2-Ml0 P H2-U02 6 Bad L2 (exec ROS) card (see MAP 050 for H2-Mll 7 jumpering).

Are any bits DOWN? 203 Y N Halt F is the device address test.

195 Is there a 1 oil the second line from the Bad keyboard PC board (see MIM top? 251). Y N Check/ replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255). 204 Bad H2 (base I/O) card. 196 Bad J2 (processor) card (see MAP 050 for -Connect the Z4 (keyboard) cable. jumpering).

Bad H2 (base I/O) card. 205 Bad F2 (Common and language ROS) card. 197 Bad H2 (base I/O) card. Bad H2 (base I/O) card. Bad J2 (processor) card (see MAP 050 for jumpering). 198 Bad H2 (base I/O) card. 206 Bad J2 (processor) card (see MAP 050 for Halt A is the BUS IN bit test. jumpering). c -Probe the BUS IN (0-7,P) lines: 199 -Switch the RUN switch under the covers to H2-Gll 5 H2-P12 0 RUN. H2-M07 4 H2-P13 6 H2-M05 3 H2-S10 P Does R7LO contain FFFF? H2-P09 2 H2-U05 1 c Y N H2-Pl0 7 (Step 206 continues) 200 Go to Page 14, Step 160, Entry Point G.

c 01JAN79 EC 836600 PEC 835541 C L MAP 0420-17

·.·.,.""""0... ,,...... __...... 1...... H J PROCESS CHECK MAP F C MAP 0420-18 2 2 2 M

PAGE 18 OF 26

(Step 206 continued) 214 Are any lines DOWN? -Power down. Y N -Remove the B2 card. -Switch the DISPLAY REGISTERS switch to 207 NORMAL. Bad J2 (processor) card (see MAP 050 - Power up. Wait 25 seconds. for jumpering). - Perform the failing job, if possible.

208 Is the PROCESS CHECK light on? Bad L2 (exec ROS) card (see MAP 050 for Y N jumpering). Bad H2 (base I/O) card. 215 Bad J2 (processor) card (see MAP 050 for Bad B2 (BSCA 1) card. jumpering). Bad F2 (Common and language ROS) card. 216 - Power down. 209 -Install the B2 card. Go to Page 15, Step 170, Entry Point C. -Power up. Wait 25 seconds. Go to Step 211, Entry Point N. 210 Is there a card in 82? 217 Y N The maximum number of I/O devices that can be attached to the 5110, is three. If a 5103 is 211 attached, it must be the last I/O device in the (Entry Point N) string of I/O devices, because it terminates all the I/O signal lines. If a 5103 is not attached, - Remove the A2, 02, K2,and K4 cards, if the last I/O device must have a cable terminator installed (see MIM 209). installed. If a 5106 is attached it must be the -Press RESTART. Wait 25 seconds. first I/O device. - Perform the failing job, if possible. A 5106 can only be attached if the 5110 has an internal tape drive. Is the PROCESS CHECK light on? Y N -Disconnect the I/O cable at the 5110 I/O interface port (see MIM 271). 212 -Switch the DISPLAY REGISTERS switch to Reinstall the cards one at a time, pressing NORMAL. RESTART and trying to run the job after -Press RESTART. Wait 25 seconds. each card. The card that causes the - Perform the failing job, if possible. PROCESS CHECK light to come on is bad. Is the PROCESS CHECK light on? 213 Y N - Reinstall the A2, 02, K2, and K4 cards. -Press RESTART. Wait 25 seconds. - Perform the failing job, if possible. Go to Page 2, Step 013, Entry Point D.

01JAN79 2 1 6 9 EC 836600 PEC 835541 C C C M N P MAP 0420-18 c PROCESS CHECK MAP c C MAP 0420-19 P R S 1 8 PAGE 19 OF 26

218 226 -Reconnect the I/O cable to the 5110 I/O The first 5114 in the string of I/O devices interface port. attached to the 5110 will be called 5114-1. -Press RESTART. Wait 25 seconds. The second 5114 will be called 5114-2. - Perform the failing job, if possible. -Disconnect 5114-2 from the 5110. Is the PROCESS CHECK light on? -Attach the cable terminator to 5114-1. Y N -Press RESTART. Wait 25 seconds. - Perform the failing job, if possible. 219 Did either LOADO or CLEAR WS (spelled Is the PROCESS CHECK light on? correctly) appear only once on one and Y N only one line of the 5110 display? Y N 227 The trouble is in 5114-2. 220 Go To Map 0400, Entry Point A. Bad 5114 C1 (adapter) card (see MAP 050 before replacing this card). 221 Check/replace the 5114 internal cables 01 The problem is repaired. and 03 (see 280 and MAP 0210). Check/replace the 5114 I/O interface 222 cable (see 280 and MAP 0210). c Is a 5103 installed? Y N If the problem still exists; -Check/ replace cables A 1D1,A102, and 223 A1D3 in 5114-1 (see Map 0210 and MIM Is a 5106 installed? 280). Y N 228 224 The trouble is in 5114-1 (Entry Point B) Bad 5114 C1 (adapter) card (see MAP 050 Are there 2 5114's installed? before replacing this card). Y N Check/replace the 5114 internal cables 01 and 03 (see 280 and MAP 0210). c: 225 Check/replace the 5114 I/O interface cable Bad A2 (I/O cable driver) card and cable (see 280 and MAP 0210). assembly in 5110. Bad A2 (I/O cable driver) card and cable Bad 5114 C1 (adapter) card (see MAP assembly in 5110. 050 before replacing this card). Bad cable terminator. Check/replace the 5114 internal cables c 01 and 03 (see 280 and MAP 0210). 229 Check/replace the 5114 I/O interface Is there a 5114 installed? cable (see 280 and MAP 0210). Y N Bad cable terminator.

01JAN79 2 2 2 2 o 0 EC 836600 PEC 835541 C C c c C Q R S T U MAP 0420-19 c C PROCESS CHECK MAP c c MAP 0420-20 T U wX 1 1 9 9 PAGE 20 OF 26

230 235 Bad A2 (I/O cable driver) card and cable Go to Page 19, Step 224, Entry Point B. assembly in 5110. Bad 5106 C1 (adapter) card (see MAP 050 for 236 jumpering). -Disconnect the 5114 from the 5106. Bad tape control card (see MIM 203). -Attach the cable terminator to the 5106. Check/ replace the tape unit cable (see MAP - Press RESTART. Wait 25 seconds. 0210 and MIM 230,231). - Perform the failing job, if possible. Check/replace the 5106 internal cables B1 and B2 (see MAP 0210 and MIM 280). Is the PROCESS CHECK light on? Check/replace the 5106 I/O interface cable Y N (see MAP 0210 and MIM 280). Bad cable terminator. 237 Were there 2 5114's installed? 231 Y N Does the PROCESS CHECK light come on as a result of powering on or pressing 238 RESTART? Bad 5114 C1 (adapter) card (see MAP 050 Y N before replacing this card). Check/ replace the 5114 internal cables D 1 232 and 03 (see 280 and MAP 0210). Does the PROCESS CH ECK occur when Check/replace the 5114 I/O interface using the 51067 cable (see 280 and MAP 0210). V N 239 233 The first 5114 in the string of I/O devices -Disconnect the 5106 from the 5110. attached to the 5110 will be called 5114-1. -Connect the 5114 that was connected to The second 5114 will be called 5114-2. the 5106, to the 5110. -Press RESTART. Wait 25 seconds. - Disconnect the cable terminator from the - Perform the failing job, if possible. 5106. -Connect 5114-1 to the 5106. Is the PROCESS CHECK light on 7 - Connect the cable terminator to 5114-1. Y N -Press RESTART. Wait 25 seconds. - Perform the failing job, if possible. 234 Bad 5106 C1 (adapter) card (see MAP Is the PROCESS CHECK light on 7 050 for jumpering). Y N Bad tape control card (see MIM 203). Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231). Check/replace the 5106 internal cables B1 and B2 (see MAP 0210 and MIM 280). Check/replace the 5106 I/O interface cable (see MAP 0210 and MIM 280).

01JAN79 2 222 1 111 EC 836600 PEC 835541 C C C ceo V WX Y Z A MAP 0420-20 c ceo PROCESS CHECK MAP o 0 MAP 0420-21 v Y Z A B C 222 2 o 0 0 0 PAGE 21 OF 26

240 ., 244 ( !>, The trouble is in 5114-2. Bad 5106 C1 (adapter) card (see MAP 050 for . ,. .. jumpering). Bad 5114 C1 (adapter) card (see MAP Bad tape control card (see MIM 203). 050 before replacing this card). Check/ replace the tape unit cable (see MAP Check / replace the 5114 internal cables 0210 and MIM 230,231). 01 and 03 (see 280 and MAP 0210). Check/replace the 5106 internal cables B1 Check/replace the 5114 I/O interface and B2 (see MAP 0210 and MIM 280). cable (see 280 and MAP 0210). Check/replace the 5106 I/O interface cable (see MAP 0210 and MIM 280). 241 The trouble is in 5114-1 . 245 Are there 2 5114'57 Bad 5114 C1 (adapter) card (see MAP 050 Y N before replacing this card). Check/replace the 5114 internal cables 01 246 and 03 (see 280 and MAP 0210). Bad A2 (I/O cable driver) card and cable Check/replace the 5114 I/O interface assembly in 5110. cable (see 280 and MAP 0210). Bad 5114 C 1 (adapter) card (see MAP 050 before replacing this card). \ 242 Check/replace the 5114 internal cables 01 Bad A2 (I/O cable driver) card and cable and 03 (see 280 and MAP 0210). CF assembly in 5110. Check/replace the 5114 I/O interface cable Bad 5106 C1 (adapter) card (see MAP 050 for (see 280 and MAP 0210). jumpering). Bad cable terminator. Bad tape control card (see MIM 203). Check/replace the tape unit cable (see MAP 247 0210 and MIM 230,231). The first 5114 in the string of I/O devices Check / replace the 5106 internal cables B 1 attached to the 5110 will be called 5114-1. The and B2 (see MAP 0210 and MIM 280). second 5114 will be called 5114-2. Check/ replace the 5106 I/O interface cable (see MAP 0210 and MIM 280). -Disconnect 5114-1 from the 5110. Bad cable terminator. -Connect 5114-2 to the 5110. -Press RESTART. Wait 25 seconds. 243 - Perform the failing job, if possible. C: -Disconnect the 5106 from the 5110. -Connect the 5114 to the 5110. Is the PROCESS CHECK light on? -Press RESTART. Wait 25 seconds. Y N - Perform the failing job, if possible.

Is the PROCESS CHECK light on? Y N

o 01JAN79 2 2 2 2 EC 836600 PEC 835541 o 0 o 0 B C o E MAP 0420-21 COD PROCESS CHECK MAP o MAP 0420-22 ODE H T 2 2 9 1 1 PAGE 22 OF 26

248 254 The trouble is in 5114-1. Does the PROCESS CHECK light come on as a result of powering on or pressing Bad 5114 C1 (adapter) card (see MAP 050 RESTART? before replacing this card). Y N Check/ replace the 5114 internal cables 01 and 03 (see 280 and MAP 0210). 255 Check/replace the 5114 I/O interface (Entry Point F) cable (see 280 and MAP 0210). - Disconnect the 5114 from the 5110. 249 -Connect the 5103 to the 5110. The trouble is in 5114-2. -Press RESTART. Wait 25 seconds. -Press and hold the CMD key. Bad 5114 C1 (adapter) card (see MAP 050 -Press the Print Display key. before replacing this card). - Release the keys. Check/replace the 5114 internal cables 01 The printer should print the information that and 03 (see 280 and MAP 0210). is displayed on the display. Check/replace the 5114 I/O interface cable (see 280 and MAP 0210). Is the PROCESS CHECK light on? Bad A2 (I/O cable driver) card and cable Y N assembly in 5110. Bad cable terminator. 256 Bad 5114 C1 (adapter) card (see MAP 050 250 before replacing this card). Is a 5106 installed? Check/replace the 5114 internal cables 01 Y N and 03 (see 280 and MAP 0210). Check/replace the 5114 I/O interface 251 cable (see 280 and MAP 0210). Is a 5114 installed? Y N 257 Bad A2 (I/O cable driver) card and cable 252 assembly in 5110. Bad 5103 B1A2 (adapter) card (see MAP Bad 5103 B1A2 (adapter) card (see MAP 050 050 for jumpering). for jumpering). Bad A2 (I/O cable driver) card and cable Check/replace the 5103 I/O interface cable assembly in 5110. (see MAP 0210 and MIM 280). Check/replace the 5103 I/O interface cable (see MAP 0210 and MIM 280).

253 Are there 2 5114'8 installed? / ' Y N

01JAN79 2 2 2 4 3 3 EC 836600 PEC 835541 DOD o F G H J MAP 0420-22

,", D D PROCESS CHECK MAP DOD MAP 0420-23 G J K L M 2 2 2 2 PAGE 23 OF 26

258 263 (Entry Point J) The trouble is in 5114-2.

( -Disconnect the 5114 from the 5110. Bad 5114 C1 (adapter) card (see MAP 050 -Connect the 5103 to the 5110. before replacing this card). -Press RESTART. Wait 25 seconds. Check/replace the 5114 internal cables D1 and D3 (see 280 and MAP 0210). Is the PROCESS CH ECK light on"1 Check/replace the 5114 I/O interface (,'" Y N cable (see 280 and MAP 0210).

259 264 Bad 5114 C1 (adapter) card (see MAP 050 Go to Page 22, Step 255, Entry Point F. before replacing this card). Check/ replace the 5114 internal cables D1 265 and D3 (see 280 and MAP 0210). The first 5114 in the string of I/O devices Check/replace the 5114 I/O interface attached to the 5110 will be called 5114-1. The cable (see 280 and MAP 0210). second 5114 will be called 5114-2.

260 -Disconnect 5114-1 from the 5110. Bad A2 (I/O cable driver) card and cable -Connect 5114-2 to the 5110. assembly in 5110. -Press RESTART. Wait 25 seconds. Bad 5103 B1A2 (adapter) card (see MAP 050 • for jumpering). Is the PROCESS CH ECK light on? Check/replace the 5103 I/O interface cable Y N (see MAP 0210 and MIM 280). 266 261 The trouble is in 5114-1. Does the PROCESS CHECK come on as a result of powering on or pressing RESTART? Bad 5114 C1 (adapter) card (see MAP 050 Y N , before replacing this card). Check/ replace the 5114 internal cables D 1 262 and D3 (see 280 and MAP 0210). The first 5114 in the string of I/O devices Check/ replace the 5114 I/O interface cable attached to the 5110 will be called 5114-1. (see 280 and MAP 0210). The second 5114 will be called 5114-2. 267 -Disconnect 5114-2 from 5114-1. - Disconnect 5114-2 from the 5110. -Connect the 5103 to 5114-1. -Connect the 5103 to the 5110. -Press RESTART. Wait 25 seconds. -Press RESTART. Wait 25 seconds. - Perform the failing job, if possible. Is the PROCESS CH ECK light on"1 Is the PROCESS CHECK light on? Y N c Y N

01JAN79 2 2 4 4 EC 836600 PEC 835541 D D D D D K L M N P MAP 0420-23 DOD PROCESS CHECK MAP DOD 0 MAP 0420-24 F N P R STU 222 233 PAGE 24 OF 26

268 274 The trouble is in 5114-2. Bad 5106 C1 (adapter) card (see MAP 050 for jumpering). Bad 5114 C1 (adapter) card (see MAP 050 Bad tape control card (see M I M 203). before replacing this card). Check/ replace the tape unit cable (see Check/replace the 5114 internal cables 01 MAP 0210 and MIM 230,231). and 03 (see 280 and MAP 0210). Check/replace the 5106 internal cables Check/replace the 5114 I/O interface B1 and B2 (see MAP 0210 and MIM cable (see 280 and MAP 0210). 280). Check/replace the 5106 I/O interface 269 cable (see MAP 0210 and MIM 280). Bad A2 (I/O cable driver) card and cable assembly in 5110. 275 Bad 5103 B1A2 (adapter) card (see MAP 050 Bad A2 (I/O cable driver) card and cable for jumpering). assembly in 5110. Check/replace the 5103 I/O interface cable Bad 5103 B1A2 (adapter) card (see MAP (see MAP 0210 and MIM 280). 050 for jumpering). Check/replace the 5103 I/O interface 270 cable (see MAP 0210 and MIM 280). Does the PROCESS CHECK light come on as a result of powering on or pressing 276 RESTART? Bad 5106 C1 (adapter) card (see MAP 050 for Y N jumpering). Bad 5103 B1A2 (adapter) card (see MAP 050 271 for jumpering). Is a 5114 installed? Bad tape control card (see MIM 203). Y N Bad A2 (I/O cable driver) card and cable assembly in 5110. 272 Check/ replace the tape unit cable (see MAP Are you using the 5106 when the 0210 and MIM 230,231). PROCESS CHECK occurs? Check/replace the 5106 internal cables B1 Y N and B2 (see MAP 0210 and MIM 280). Check/replace the 5106 I/O interface cable 273 (see MAP 0210 and MIM 280). -Disconnect the 5106 from the 5110. Check/replace the 5103 I/O interface cable -Connect the 5103 to the 5110. (see MAP 0210 and MIM 280). -Press RESTART. Wait 25 seconds. -Perform the failing job, if possible. 277 Are you using the 5106 when the PROCESS Is the PROCESS CHECK light on? CHECK occurs? Y N Y N

01JAN79 2 2 2 5 5 5 EC 836600 PEC 835541 00000 o 0 Q R STU V W MAP 0420-24 D D PROCESS CHECK MAP D D D MAP 0420-25 V W X y 2 2 ~ 4 4 4 PAGE 25 OF 26

278 282 -Disconnect the 5106 from the 5110. Bad 5114 C 1 (adapter) card (see MAP 050 -Connect the 5114 to the 5110. before replacing this card). -Press RESTART. Wait 25 seconds. Check/replace the 5114 internal cables D1 - Perform the failing job, if possible. and D3 (see 280 and MAP 0210). Check/replace the 5114 I/O interface Is the PROCESS CHECK light on? cable (see 280 and MAP 0210). Y N 283 279 Bad 5106 C1 (adapter) card (see MAP 050 for Bad 5106 C1 (adapter) card (see MAP 050 jumpering). for jumpering). Bad tape control card (see MIM 203). Bad tape control card (see MIM 203). Bad 5103 B 1A2 (adapter) card (see MAP 050 Check/ replace the tape unit cable (see for jumpering). MAP 0210 and MIM 230,231). Bad A2 (I/O cable driver) card and cable Check/replace the 5106 internal cables B1 assembly in 5110. and B2 (see MAP 0210 and MIM 280). Check/ replace the tape unit cable (see MAP Check/replace the 5106 I/O interface 0210and MIM 230,231). cable (see MAP 0210 and MIM 280). Check/replace the 5106 internal cables B1 and 82 (see MAP 0210 and MIM 280). I 280 Check/replace the 5106 I/O interface cable Bad 5114 C1 (adapter) card (see MAP 050 (see MAP 0210 and MIM 280). before replacing this card). Check/replace the 5103 I/O interface cable Bad 5103 B 1A2 (adapter) card (see MAP 050 (see MAP 0210 and MIM 280). for jumpering). Bad A2 (I/O cable driver) card and cable 284 assembly in 5110. Is a 5114 installed? Check/replace the 5114 internal cables D1 Y N and D3 (see 280 and MAP 0210). Check/replace the 5114 I/O interface cable 285 (see 280 and MAP 0210). -Disconnect the 5106 from the 5110. Check/replace the 5103 I/O interface cable -Connect the 5103 to the 5110. (see MAP 0210 and MIM 280). -Press RESTART. Wait 25 seconds.

281 Is the PROCESS CHECK light on? -Disconnect the 5114 from the 5106. Y N -Connect the 5103 to the 5106. -Press RESTART. Wait 25 seconds. - Perform the failing job, if possible.

Is the PROCESS CHECK light on? Y N

01JAN79 222 666 EC 836600 PEe 835541 D D DEE X y Z A B MAP 0420-25 C 0 E E PROCESS CHECK MAP o E MAP 0420-26 N Z A B 2 2 1 222 8 5 5 5 PAGE 26 OF 26

286 292 Bad 5106 C 1 (adapter) card (see MAP -Switch the DISPLAY REGISTERS switch to 050 for jumpering). NORMAl. Bad tape control card (see MIM 203). Check/ replace the tape unit cable (see Go To Map 0500, Entry Point A. MAP 0210 and MIM 230,231). Check/replace the 5106 internal cables 293 B1 and B2 (see MAP 0210 and MIM Go to the FREELANCE TROUBLESHOOTING 280). GUIDE in the DIAGNOSTIC AIDS section of the Check/replace the 5106 I/O interface MIM. cable (see MAP 0210 and MIM 280).

287 Bad A2 (I/O cable driver) card and cable assembly in 5110. Bad' 5103 B1A2 (adapter) card (see MAP 050 for jumpering). Check/replace the 5103 I/O interface cable (see MAP 0210 and MIM 280).

288 -Disconnect the 5106 from the 5110. -Connect the 5114 to the 5110. -Press RESTART. Wait 25 seconds.

Is the PROCESS CHECK light on1 Y N

289 Bad 5106 C1 (adapter) card (see MAP 050 for jumpering). Bad tape control card (see MIM 203). Check/ replace the tape unit cable (see MAP 0210 and MIM 230,231). Check/replace the 5106 internal cables B1 and B2 (see MAP 0210 and MIM 280). Check/replace the 5106 I/O interface cable (see MAP 0210 and MIM 280).

290 Go to Page 23, Step 258, Entry Point J.

291 Go to Page 2, Step 012, Entry Point M.

01JAN79

EC 836600 PEC 835541

MAP 0420-26 DISPLAY MAP 0500 MAP 0500-1 ( PAGE 1 OF 19

ENTRY POINTS EXIT POINTS (",'" FROM ENTER THIS MAP EXIT THIS MAP TO MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT

0200 A 001 2 004 0700 A 0420 A 001 3 016 0700 A (:"" 0450 A 001 17 163 0700 A 0900 A 001 16 148 0700 A

001 (Entry Point A)

-Press the top, then the bottom of the REVERSE DISPLAY switch.

Does the background of the 5110 display change from dark to light? Y N

002 I -Press the bottom of the REVERSE DISPLAY switch. -Probe G2-M03 (-reverse display). (See appendix B, the general logic probe, in the 5110 MIM).

Is the UP light on? Y N

003 -Calibrate the multimeter (see MIM 270). - Measure the following voltages with ',' reference to J6-C02 (gnd) : ( - )/

+12 Vdc J6E04 +8.5 Vdc G2J 11 +5 Vdc G2D03 -5 Vdc F2M06 (Step 003 continues)

© Copyright IBM Corp. 1979 01JAN79 1 EC 836600 PEC 835541 9 2 A B MAP 0500-1 DISPLAY MAP B MAP 0500-2 1

PAGE 2 OF 19

(Step 003 continued) 010 Are the voltages in tolerance (11.0 to 13.2 -Press the top of the REVERSE DISPLAY switch. Vdc, 7.9 to 9.35 Vdc, and 4.6 to 5.5 Vdc)? -Probe G2-M03 (-reverse display). Y N Is the DOWN light on? 004 Y N Go To Map 0700, Entry Point A. 011 005 Bad REVERSE DISPLAY switch. -Probe G2-M03 (-reverse display). Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 248,249). Is the DOWN light on? Y N 012 -Press the bottom of the REVERSE DISPLAY 006 switch. Bad G2 (display) card (see MAP 050 for -Adjust the BRIGHTNESS control to the center of jumpering). its range. Bad REVERSE DISPLAY switch. Check/ replace Z3 (display and control panel) Is the 5110 display completely dark? cable (see MAP 0210 and MIM 248,249). Y N

007 013 - Remove the G2 (display) card. (Entry Point H) -Probe G2-M03 (-reverse display). -Attach a jumper from G2-P02 (-I/O display Is the DOWN light on? off) to D08 (gnd). Y N Is there video (any black image) within the 008 raster area of the 5110 display? Bad G2 (display) card (see MAP 050 for Y N jumpering). 014 009 Is the raster a stable white background - Reinstall the G2 (display) card. of the correct size and shape? Y N Bad REVERSE DISPLAY switch. Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 248,249).

01JAN79

1 1 EC 836600 PEC 835541 7 6 3 3 C D E F MAP 0500-2 F DISPLAY MAP E MAP 0500-3 2 ( 2 PAGE 3 OF 19

015 022 - Remove the jumper from G2-P02. -Remove the jumper from G2-P02. -Calibrate the multimeter (see MIM 270). -Press the top of the REVERSE DISPLAY switch. ( - Measure +12 Vdc from J6-E04 (+ 12 Vdc) to J6-C02 (gnd). Is the background of the 5110 display now (See MIM 248 display Z3 socket locations). black instead of white? Y N Is the voltage in tolerance (+11.0 Vdc to +13.2 (""'~ Vdc)? 023 Y N Bad G2 (display) card (see MAP 050 for jumpering). 016 Go To Map 0700, Entry Point A. 024 -Press the bottom of the REVERSE DISPLAY 017 switch. -Probe G2-J02 (-external vertical sync). -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. Are both lights on and steady? Y N Is there video (any black image) on the display screen? 018 Y N - Disconnect the cable from Z3. - Probe G2-J02. 025 - Probe G2-B03 (-I/O display off). Are both lights on and steady? Y N Is only the DOWN light on? • Y N 019 -Connect the Z3 (display and control panel) 026 cable. -Probe G2-B12 (-machine video)

Bad G2 (display) card (see MAP 050 for Are both lights on and steady? jumpering). Y N

020 027 Bad display assembly (see MIM 204). -Disconnect the cable from Z3 (see MIM c' Check/ replace Z3 (display and control panel) 209) cable (see MAP 0210 and MIM 248,249). -Probe G2-B12.

021 Are both lights on and steady? Bad G2 (display) card (see MAP 050 for Y N jumpering). c: Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 248,249). Bad display assmbly (see MIM 204), also see MIM 247 before replacing the display assmbly.

01JAN79

EC 836600 PEC 835541 5 5 444 G H J K L MAP 0500-3 J K L DISPLAY MAP M MAP 0500-4 333

PAGE 4 OF 19

028 034 - Reconnect the Z3 cable. -Observe the 5110 display. -Press the top of the REVERSE DISPLAY switch. Bad G2 (display) card (see MAP 050 for -Adjust the BRIGHTNESS control from one limit jumpering). to the other. Bad H2 (base I/O) card. Bad J2 (processor) card (see MAP 050 for Is there any video (any white image) on the jumpering). display screen? Y N 029 Bad display assembly (see MIM 204). 035 Check/replace Z3 (display and control panel) Is there a card installed in K2 (Parallel cable (see MAP 0210 and MIM 248,249). I/O)? Y N 030 -Probe the following pins: 036 Bad H2 (base I/O) card. G2-J05 (+C2) Bad J2 (processor) card (see MAP 050 for G2-P04 (+C4) jumpering). Bad G2 (display) card (see MAP 050 for Are both lights on for all probe points? jumpering). Y N Bad display assembly (see M I M 204). Check/ replace Z3 (display and control 031 panel) cable (see MAP 0210 and MIM -Remove the G2 card. 248,249). -Probe G2-J05 and G2-P04 again. 037 Are both lights on for all probe points? - Remove the K2 card. Y N -Adjust the BRIGHTNESS control from on limit to the other. 032 Bad F2 (Common and language ROS) card. Is there any video on the display screen? Bad H2 (base I/O) card. Y N Bad J2 (processor) card (see MAP 050 for jumpering). 038 Bad H2 (base I/O) card. 033 Bad J2 (processor) card (see MAP 050 for Bad G2 (display) card (see MAP 050 for jumpering). jumpering). Bad G2 (display) card (see MAP 050 for jumpering). Bad display assembly (see MIM 204). Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 248,249).

01JAN79

EC 836600 PEC 835541 5 5 M N P MAP 0500-4 G H N P DISPLAY MAP R S MAP 0500-5 ( 3 344 PAGE 5 OF 19

039 044 Bad K2 (Parallel I/O) card. -Remove the G2 (display) card. -Probe G2-B06. 040 Check/ replace Z3 (display and control With the switch in DISPLAY REGISTERS the panel) cable (see MAP 0210 and MIM DOWN light should be on. In NORMAL, both 248,249). lights should be off. Bad BRIGHTNESS control Are the probe indications correct? 041 Y N Bad G2 (display) card (see MAP 050 for jumpering). 045 Bad H2 (base I/O) card. - Reinstall the G2 (display) card. Bad J2 (processor) card (see MAP 050 for jumpering). Bad J2 (processor) card (see MAP 050 for Check/ replace Z3 (display and control panel) jumpering). cable (see MAP 0210 and MIM 248,249). Bad DISPLAY REGISTERS switch (see MIM 249). 042 Check/replace Z3 (display and control -Switch the RUN switch under the covers to NOT panel) cable (see MIM 248,249). RUN. -Observe the 5110 display. 046 -Switch the DISPLAY REGISTERS switch to Bad G2 (display) card (see MAP 050 for NORMAL then back to DISPLAY REGISTERS. jumpering).

Is the video different in DISPLAY REGISTERS 047 • than in NORMAL 7 (The answer is Y if the Are there any I/O devices attached to the machine is operating properly). 5110 I/O interface port (see MIM 271)7 Y N Y N

043 048 -Switch the RUN switch under the covers to Bad G2 (display) card (see MAP 050 for RUN. jumpering). -Probe G2-B06 (-display reg). Bad H2 (base I/O) card. Bad F2 (Common and language ROS) card. With the switch in DISPLAY REGISTERS the DOWN light should be on. In NORMAL, the UP light should be on.

Are the probe indications correct? Y N

C: 01JAN79 1 EC 836600 PEC 835541 1 6 Q R S T MAP 0500-5 T DISPLAY MAP u V MAP 0500-6 5

PAGE 6 OF 19

049 052 -Remove the cable from the 5110 I/O interface Bad A2 (I/O cable driver) card and cable port. (see MIM 271) assembly.

No more than 25 seconds after RESTART is 053 pressed, the following events should occur: (Entry Point G) 1. ABCDEFGH appears on the top line of the 5110 display. The maximum number of I/O devices that can 2. ABCDEFGHJKLMNP appears on the top line. be attached to the 5110 is three. If a 5103 is 3. The top line is cleared and either LOADO or installed, it has to be the last I/O device in the CLEAR WS appears once on one and only string of devices, because it terminates all the one line of the 5110 display. I/O signal lines. If a 5103 is not installed, the last I/O device must have a cable terminator -Press RESTART. installed. If a 5106 is installed, it has to be the first I/O device in the string of devices. Do all three events shown above occur in sequence after RESTART is pressed? Was there a 5103 in the string of devices you V N disconnected from the 5110 I/O interface port? 050 V N - Remove the A2 (I/O cable driver) card and cable. 054 Was there a 5106 in the string of devices? No more than 25 seconds after RESTART is V N pressed, the following events should occur: 1. ABCDEFGH appears on the top line of the 055 5110 display. Bad A2 (I/O cable driver) card and cable 2. ABCDEFGHJKLMNP appears on the top assembly in 5110. line. Bad 5114 C1 (adapter) card (see MAP 050 3. The top line is cleared and either LOADO before replacing this card). or CLEAR WS appears once on one and Check/replace the 5114 internal cables D1 only one line of the 5110 display. and 03 (see 280 and MAP 0210). Check/replace the 5114 I/O interface -Press RESTART. cable (see 280 and MAP 0210).

Do all three events shown above occur in sequence after RESTART is pressed? V N

051 Bad G2 (display) card (see MAP 050 for jumpering). Bad H2 (base I/O) card. Bad F2 (Common and language ROS) card.

01JAN79

EC 836600 PEC 835541 8 7 u V WX MAP 0500-6 X DISPLAY MAP z MAP 0500-7 ( 6 PAGE 7 OF 19

(Step 060 continued) 056 -Connect the 5106 to the 5110 I/O interface -Press RESTART. (:.'" port. -Attach the cable terminator to the 5106. Do all three events shown above occur in No more than 25 seconds after RESTART is sequence after RESTART is pressed? pressed, the following events should occur: Y N 1. ABCDEFGH appears on the top line of the -,." 5110 display. 061 2. ABCDEFGHJKLMNP appears on the top line. The trouble is fixed.

( / 3. The top line is cleared and either LOA DO or CLEAR WS appears once on one and only 062 one line of the 5110 display. Bad 5114 C1 (adapter) card (see MAP 050 before replacing this card). - Press RESTART. Check/ replace the 5114 internal cables 01 and 03 (see 280 and MAP 0210). Do all three events shown above occur in Check/replace the 5114 I/O interface cable sequence after RESTART is pressed? (see 280 and MAP 0210). Y N 063 057 The first 5114 in the string of I/O devices Was there a 5114 installed? attached to the 5110 will be called 5114-1. The Y N second 5114 will be called 5114-2.

058 -Connect 5114-1 to the 5106. The trouble is fixed. -Attach the cable terminator to 5114-1. • No more than 25 seconds after RESTART is 059 pressed, the following events should occur: Were there two 5114's installed? 1. ABCDEFGH appears on the top line of the Y N 5110 display. 2. ABCDEFGHJKLMNP appears on the top line. 060 3. The top line is cleared and either LOADO or - Disconnect the cable terminator from the CLEAR WS appears once on one and only 5106. one line of the 5110 display. -Connect the 5114 to the 5106. -Attach the cable terminator to the 5114. -Press RESTART. No more than 25 seconds after RESTART is pressed, the following events should Do all three events shown above occur in occur: sequence after RESTART is pressed? 1. ABCDEFGH appears on the top line of Y N the 5110 display. 2. ABCOEFGHJKLMNP appears on the top line. 3. The top line is cleared and either LOAOO or CLEAR WS appears once on one and only one line of the 5110 display. (Step 060 continues) c 01JAN79 8 8 EC 836600 PEC 835541 8 A A y Z A B MAP 0500-7 A A DISPLAY MAP wy MAP 0500-8 A B 6 7 7 7 PAGE 8 OF 19

064 068 -Connect 5114-2 to 5114-1. Bad A2 (I/O cable driver) card and cable -Attach the cable terminator to 5114-2. assembly in 5110. No more than 25 seconds after RESTART is Bad 5106 C 1 (adapter) card (see MAP 050 for pressed, the following events should occur: jumpering). 1. ABCOEFGH appears on the top line of the Check/replace the 5106 internal cables B1 5110 display. and B2 (see MAP 0210 and MIM 280). 2. ABCOEFGHJKLMNP appears on the top Check/ replace the 5106 I/O interface cable line. (see MAP 0210 and MIM 280). 3. The top line is cleared and either LOAOO Bad cable terminator. or CLEAR WS appears once on one and only one line of the 5110 display. 069 -Connect the 5103 to the 5110. -Press RESTART. No more than 25 seconds after RESTART is pressed, the following events should occur: Do all three events shown above occur in 1. ABCOEFGH appears on the top line of the sequence after RESTART is pressed? 5110 display. Y N 2. ABCOEFGHJKLMNP appears on the top line. 3. The top line is cleared and either LOAOO or 065 CLEAR WS appears once on one and only The trouble is fixed. one line of the 5110 display.

066 -Press RESTART. The trouble is in 5114-2 Do all three events shown above occur in Bad 5114 C1 (adapter) card (see MAP 050 sequence after RESTART is pressed? before replacing this card). Y N Check/replace the 5114 internal cables 01 and 03 (see 280 and MAP 0210). 070 Check/replace the 5114 I/O interface cable Bad A2 (I/O cable driver) card and cable (see 280 and MAP 0210). assembly in 5110. Bad 5103 B1A2 (adapter) card (see MAP 050 067 for jumpering). The trouble is in 5114-1 Check/replace the 5103 I/O interface cable (see MAP 0210 and MIM 280). Bad 5114 C1 (adapter) card (see MAP 050 before replacing this card). 071 Check/replace the 5114 internal cables 01 and Was there a 5114 in the string of devices '7 03 (see 280 and MAP 0210). Y N Check/replace the 5114 I/O interface cable (see 280 and MAP 0210). 072 Was there a 5106 in the string of devices '7 Y N

073 The trouble is fixed.

01JAN79 9 9 EC 836600 PEC 835541 A A C 0 MAP 0500-8 A A DISPLAY MAP A MAP 0500-9 C 0 F 8 8

PAGE 9 OF 19

074 078 -Disconnect the 5103 from the 5110. -Disconnect the 5103 from the 5110. -Connect the 5106 to the 5110. -Connect the 5114 to the 5110. -Connect the 5103 to the 5106. - Connect the 51 03 to the 5114. No more than 25 seconds after RESTART is No more than 25 seconds after RESTART is pressed, the following events should occur: pressed, the following events should occur: 1. ABCDEFGH appears on the top line of the 1. ABCDEFGH appears on the top line of the 5110 display. 5110 display. (0' 2. ABCDEFGHJKLMNP appears on the top 2. ABCDEFGHJKLMNP appears on the top line. line. 3. The top line is cleared and either LOADO or 3. The top line is cleared and either LOADO CLEAR WS appears once on one and only or CLEAR WS appears once on one and one line of the 5110 display. only one line of the 5110 display. - Press RESTART. -Press RESTART. Do all three events shown above occur in Do all three events shown above occur in sequence after RESTART is pressed? sequence after RESTART is pressed? Y N Y N 079 075 Bad 5114 C1 (adapter) card (see MAP 050 Bad 5106 C1 (adapter) card (see MAP 050 before replacing this card). for jumpering). Check/replace the 5114 internal cables 01 Check/replace the 5106 internal cables B1 and D3 (see 280 and MAP 0210). I and B2 (see MAP 0210 and MIM 280). Check/replace the 5114 I/O interface cable Check/replace the 5106 I/O interface (see 280 and MAP 0210). cable (see MAP 0210 and MIM 280). 080 076 Was a 5106 installed? The trouble is fixed. Y N

077 081 Were there two 5114's in the string? The trouble is fixed. Y N

.~, ( "'."

01JAN79 1 1 o o EC 836600 PEC 835541 A A A E F G MAP 0500-9 A A DISPLAY MAP MAP 0500-10 E G 9 9 PAGE 10 OF 19

(Step 085 continued) 082 one line of the 5110 display. -Disconnect the 5114 from the 5110. -Connect the 5106 to the 5110. -Press RESTART. -Connect the 5114 to the 5106. No more than 25 seconds after RESTART is Do all three events shown above occur in pressed, the following events should occur: sequence after RESTART is pressed? 1. ABCDEFGH appears on the top line of the V N 5110 display. 2. ABCDEFGHJKLMNP appears on the top 086 line. -Disconnect 5114-2 from the 5110. 3. The top line is cleared and either LOADO -Connect 5114-1 to the 5110. or CLEAR WS appears once on one and -Connect 5114-2 to 5114-1. only one line of the 5110 display. No more than 25 seconds after RESTART is pressed, the following events should occur: -Press RESTART. 1. ABCDEFGH appears on the top line of the 5110 display. Do all three events shown above occur in 2. ABCDEFGHJKLMNP appears on the top sequence after RESTART is pressed? line: V N 3. The top line is cleared and either LOADO or CLEAR WS appears once on one and 083 only one line of the 5110 display. Bad 5106 C1 (adapter) card (see MAP 050 for jumpering). -Press RESTART. Check/replace the 5106 internal cables B1 and B2 (see MAP 0210 and MIM 280). Do all three events shown above occur in Check/replace the 5106 I/O interface sequence after RESTART is pressed? cable (see MAP 0210 and MIM 280). V N

084 087 The trouble is fixed. The trouble is in 5114-1

085 Bad 5114 C 1 (adapter) card (see MAP 050 The first 5114 in the string of I/O devices before replacing this card). attached to the 5110 will be called 5114-1. The Check/replace the 5114 internal cables D1 second 5114 will be called 5114-2. and D3 (see 280 and MAP 0210). Check/replace the 5114 I/O interface -Disconnect the 5103 from the 5110. cable (see 280 and MAP 0210). -Connect 5114-2 to the 5110. -Connect the 5103 to 5114-2. 088 No more than 25 seconds after RESTART is The trouble is fixed. pressed, the following events should occur: 1. ABCDEFGH appears on the top line of the 5110 display. 2. ABCDEFGHJKLMNP appears on the top line. 3. The top line is cleared and either LOADO or CLEAR WS appears once on one and only (Step 085 continues)

01JAN79 1 1 EC 836600 PEC 835541 A H MAP 0500-10 DISPLAY MAP A A A A MAP 0500-11 ~ ft L M N P 1 o PAGE 110F 19

089 095 The trouble is in 5114-2 -Install G2 -Remove the 02 (ASYNC COM-Serial Bad 5114 C1 (adapter) card (see MAP 050 I/O) card before replacing this card). -Probe G2-P04 Check/replace the 5114 internal cables 01 and 03 (see 280 and MAP 0210). Are both lights on and steady? Check/replace the 5114 I/O interface cable Y N (see ,280 and MAP 0210). 096 090 -Install 02 Is the display tilted? - Remove the A2 (I/O cable driver) Y N card -Probe G2-P04 091 -Probe G2-P04 (+C4). Are both lights on and steady? Y N Are both lights on and steady? Y N 097 Reinstall the A2 card. 092 Bad H2 (base I/O) card. -Probe G2-P04. Bad J2 (processor) card (see MAP 050 for jumpering). Are both lights off? I Y N 098 Bad A2 (I/O cable driver) card and 093 cable assembly. -Remove the F2 (ROS control) card. -Probe G2-P04. 099 Bad 02 (Async Comm-Seriall/O) card. Are both lights on and steady? Y N 100 Bad G2 (display) card (see MAP 050 for 094 jumpering). - Reinstall F2. - Remove the G2 (display) card. 101 -Probe G2-P04. Bad F2 (Common and language ROS) card.

Are both lights on and steady? 102 Y N Bad H2 (base I/O) card. c:

01JAN79 1 1 6 2 EC 836600 PEC 835541 A A A A A A JKLMNP MAP 0500-11 A DISPLAY MAP A A A MAP 0500-12 K R S T 1 1 ". " PAGE 120F 19

103 108 -Switch the L32-64-R32 switch to all three - Disconnect the cable from Z3. positions and observe the display. -Probe K6-A02.

Does the video change correctly as the Are both lights on and steady 1 switch is operated? Y N Y N 109 104 -Connect the Z3 (display and control Bad G2 (display) card (see MAP 050 for panel~ cable. jumpering). Bad display L32-64-R32 switch. Bad G2 (display) card (see MAP 050 for Check/ replace Z3 (display and control panel) jumpering). cable (see MAP 0210 and MIM 248,249). 110 105 Bad display assembly (see MIM 204). -Switch the RUN switch under the covers to Check/ replace Z3 (display and control RUN. panel) cable (see MAP 0210 and MIM -Switch the DISPLAY REGISTERS switch to 248,249). DISPLAY REGISTERS. 111 Does the failure appear as long vertical lines Bad display assembly (see MIM 204). (exceeding several characters in length), on Check/ replace Z3 (display and control panel) the display? cable (see MAP 0210 and MIM 248,249). Y N 112 106 -Switch the RUN switch under the covers to -Switch the RUN switch under the covers to RUN. NOT RUN. -Switch the DISPLAY REGISTERS switch to NORMAL. Is the video on the display stable1 Y N No more than 25 seconds after RESTART is pressed, the following events should occur: 107 1. ABCDEFGH appears on the top line of the -Switch the RUN switch under the covers 5110 display. to RUN. 2. ABCDEFGHJKLMNP appears on the top line. -Probe K6-A02 (-external vertical sync). 3. The top line is cleared and either LOADO or (See M I M 248 display Z3 socket CLEAR WS appears once on one and only locations). one line of the 5110 display.

Are both lights on and steady? -Press RESTART. Y N Do all three events shown above occur in sequence after RESTART is pressed? Y N II 01JAN79 1 1 1 6 4 3 EC 836600 PEC 835541 A A A A A A Q R S T U V MAP 0500-12 A DISPLAY MAP A A MAP 0500-13 V X y 1 2 PAGE 13 OF 19

113 117 Is there a card in A2 or 82 or 02 or K21 -Power down. Y N -Swap M2 with M4. -Power up. Wait 25 seconds. 114 No more than 25 seconds after power up, the (Entry Point I) following events should occur: 1. ABCDEFGH appears on the top line of the Is there a card in M4 or N2 or N41 5110 display. (', Y N 2. ABCDEFGHJKLMNP appears on the top line. 115 3. The top line is cleared and either LOADO Bad G2 (display) card (see MAP 050 for or CLEAR WS appears once on one and jumpering). only one line of the display. Bad J2 (processor) card (see MAP 050 for jumpering). -Power up. Bad H2 (base I/O) card. Bad L2 (exec ROS) card (see MAP 050 for Do all three events shown above occur in jumpering). sequence after Power Up 1 Bad M2 (read/write storage) card. V N

116 118 - Power down. Bad G2 (display) card (see MAP 050 for -Remove M4,N2, and N4 if installed. jumpering). - Power up. Wait 25 seconds. Bad J2 (processor) card (see MAP 050 for I No more than 25 seconds after power up, the jumpering). following events should occur: Bad H2 (base I/O) card. 1. ABCDEFGH appears on the top line of the Bad L2 (exec ROS) card (see MAP 050 for 5110 display. jumpering). 2. ABCDEFGHJl(LMNP appears on the top line. 119 3. The top line is cleared and either LOADO The read/write storage card that was in M2 is or CLEAR WS appears once on one and bad. only one line of the display. 120 -Power up. One of the read write storage cards removed is bad. Power down. Install the cards one at a Do all three events shown above occur in time, (M4 first, then N2, N4), to find the bad sequence after Power Up 1 card. Power up after each card is installed. Use Y N the preceeding step to determine which card is bad.

01JAN79 c 1 4 EC 836600 PEC 835541 A A A WX y MAP 0500-13 A DISPLAY MAP A A MAP 0500-14 W U Z 1 1 3 2 PAGE 14 OF 19

121 125 -Remove the cards from A2,B2,D2, and K2 if Is there a cable connected to the 5110 I/O installed. interface port? No more than 25 seconds after RESTART is Y N pressed, the following events should occur: 1. ABCDEFGH appears on the top line of the 126 5110 display. Bad A2 (I/O cable driver) card and cable 2. ABCDEFGHJKLMNP appears on the top line. assembly. 3. The top line is cleared and either LOADO or CLEAR WS appears once on one and only 127 one line of the 5110 display. -Install the A2 card. - Remove the I/O interface cable from the -Press RESTART. 5110 I/O interface port. No more than 25 seconds after RESTART is Do a" three events shown above occur in pressed, the following events should occur: sequence after RESTART is pressed? 1. ABCDEFGH appears on the top line of the Y N 5110 display. 2. ABCDEFGHJKLMNP appears on the top 122 line. Go to Page 13, Step 114, Entry Point I. 3. The top line is cleared and either LOADO or CLEAR WS appears once on one and 123 only one line of the 5110 display. -Install B2,D2, and K2 if removed. No more than 25 seconds after RESTART is -Press RESTART. pressed, the following events should occur: 1. ABCDEFGH appears on the top line of the Do all three events shown above occur in 5110 display. sequence after RESTART is pressed? 2. ABCDEFGHJKLMNP appears on the top line. Y N 3. The top line is cleared and either LOA DO or CLEAR WS appear.s once on one and only 128 one line of the 5110 display. Bad A2 (I/O cable driver) card and cable assembly. - Press RESTART. 129 Do all three events shown above occur in Go to Page 6, Step 053, Entry Point G. sequence after RESTART is pressed? Y N 130 Is there a flashing cursor displayed only on 124 the line below CLEAR WS or LOADO once One of the cards you just installed is bad. and only once? Remove them one at a time, pressing Y N RESTART after each card is replaced. The card that causes the display to NOT fail is bad.

01JAN79 1 1 5 5 EC 836600 PEC 835541 A B B Z A B MAP 0500-14 B DISPLAY MAP B B B MAP 0500-15 B A C D 1 1 4 4 (~ PAGE 15 OF 19

131 136 Are there any read/write storage cards in M4, The card that was in M2 is bad N2, or N4? .'..... , Y N 137 ( One of the cards removed is bad. Reinstall 132 them one at a time (M4 first, then N2, N4) to Bad M2 (read/write storage) card. find the bad card. Bad G2 (display) card (see MAP 050 for jumpering). 138 ('''' Bad H2 (base I/O) card. - Enter the following characters in order: Bad J2 (processor) card (see MAP 050 for 4455@@@ jumpering). Bad L2 (exec ROS) card (see MAP 050 for Is 4455@@@ followed by a flashing cursor, jumpering). displayed on the line below CLEAR WS or LOA DO once and only once? 133 Y N -Power down. - Remove the storage cards M4, N2, and N4 if 139 installed. Are there any read/write storage cards in - Power up. Wait 25 seconds. M4, N2, or N4? Y N Is there a flashing cursor displayed only on the line below CLEAR WS or LOADO once 140 and only once? Bad M2 (read/write storage) card. Y N Bad G2 (display) card (see MAP 050 for jumpering). • 134 Bad H2 (base I/O) card. - Power down. Bad J2 (processor) card (see MAP 050 for -Remove the read/write storage card in M2. jumpering). -Install one of the other read/write storage Bad L2 (exec ROS) card (see MAP 050 for cards into the M2 location. jumpering). - Power up. Wait 25 seconds. 141 Is there a flashing cursor displayed only on - Power down. the line below CLEAR WS or LOADO, once - Remove the storage cards M4, N2, and N4 . and only once? - Power up. Wait 25 seconds. Y N - Enter the following characters in order. 4455@@@ 135 Bad G2 (display) card (see MAP 050 for Is 4455@@@ followed by a flashing jumpering). cursor, displayed on the line below CLEAR Bad H2 (base I/O) card. WS or LOADO once and only once? Bad J2 (processor) card (see MAP 050 for Y N jumpering). Bad L2 (exec ROS) card (see MAP 050 for jumpering).

01JAN79 111 CI 666 EC 836600 PEC 835541 B B B B B C D E F G MAP 0500-15 B B B DISPLAY MAP o A A MAP 0500-16 E F G 111 2 ~ 9 555 1 2 PAGE 16 OF 19 I 142 147 - Power down. -Calibrate the multimeter (see MIM 270). -Remove the read/write storage card in -Measure +8.5 Vdc at board location M2. C1-C13. -Install one of the other read/write storage card into the M2 card location. Is the voltage in tolerance (+7.8 Vdc to -Power up. Wait 25 seconds. +9.3 Vdc)? - Enter the following characters in order, Y N 4455@@@ 148 Is 4455@@@ followed by a flashing Go To Map 0700, Entry Point A. cursor, displayed on the line below CLEAR WS or LOADO once and only 149 once? -Measure G2-J11 (+8.5 Vdc) to G2-D08 Y N (gnd).

143 Is the voltage in tolerance (+7.8 Vdc to Bad G2 (display) card (see MAP 050 for +9.3 Vdc)? jumpering). Y N Bad H2 (base I/O) card. Bad J2 (processor) card (see MAP 050 150 for jumpering). The circuit is open between the power Bad L2 (exec ROS) card (see MAP 050 supply connector Y1 (A 1 board location for jumpering). C1-C13) and G2-J11 .

144 151 The card that was in M2 is bad Bad G2 (display) card (see MAP 050 for jumpering). 145 One of the cards removed is bad. Reinstall 152 them one at a time (M4 first, then N2, N4) to See 247 (Display Raster Adjustments) find the bad card. 153 146 -Probe G2-J05 (+C2 PWRD). Bad M2 (read/write storage) card. Bad G2 (display) card (see MAP 050 for Are both lights on and steady? jumpering). Y N Bad H2 (base I/O) card. Bad J2 (processor) card (see MAP 050 for 154 jumpering). Is the DOWN light on? Bad L2 (exec ROS) card (see MAP 050 for Y N jumpering). 155 Bad J2 (processor) card (see MAP 050 for jumpering). Bad H2 (base I/O) card.

01JAN79 / 1 1 7 7 EC 836600 PEC 835541 B B H J MAP 0500-16 eBB DISPLAY MAP B B B MAP 0500-17 2 H J K L M 1 1 6 6 PAGE 17 OF 19

156 162 - Remove the F2 card. -Disconnect the cable from Z3. (see MIM 209). Are both lights on and steady? V N Is the voltage in tolerance (+11.0 Vdc to +13.2 Vdc)? 157 Y N - Reinstall F2. 163 Bad G2 (display) card (see MAP 050 for -Connect the Z3 (display and control jumpering). panel) cable. Bad H2 (base I/O) card. Bad J2 (processor) card (see MAP 050 Go To Map 0700, Entry Point A. for jumpering). 164 158 Bad display assembly (see MIM 204). Bad F2 (Common and language ROS) card. Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 159 248,249). Bad G2 (display) card (see MAP 050 for jumpering). 165 Bad display assembly (see MIM 204). 160 Check/ replace Z3 (display and control panel) (Entry Point B) cable (see MAP 0210 and MIM 248,249).

166 • ***** CAUTION ***** High voltage is present. -Probe G2-P07 (+C5).

Check closely --- is the machine CRT filament Are both lights on and steady? glowing (observe through the glass at the V N socket end of the CRT)? Y N 167 (Entry Point C) 161 -Calibrate the multimeter (see MIM 270). - Remove the F2 card. -Measure +12 Vdc from J6-E04 to J6-C02 -Probe G2-P07. (gnd). (See MIM 248 display Z3 socket locations). Are both lights on and steady? V N Is the voltage in tolerance (+11.0 Vdc to +13.2 Vdc)? c V N

01JAN79 o 1 1 1 888 EC 836600 PEC 835541 B B B B B B K L M N P Q MAP 0500-17 B B B DISPLAY MAP B B B MAP 0500-18 ~ ) 9 STU 777 I PAGE 18 OF 19 168 175 - Reinstall the F2 card. -Connect the Z3 (display and control panel) - Remove the G2 (display) card. cable. -Probe G2-P07. Is there a card in 02? Are both lights on and steady? Y N Y N 176 169 Bad G2 (display) card (see MAP 050 for - Reinstall the G2 card. jumpering).

Bad J2 (processor) card (see MAP 050 177 for jumpering). -Remove the D2 (ASYNC COM-Serial I/O) Bad H2 (base I/O) card. card. -Probe G2-B09 170 Bad G2 (display) card (see MAP 050 for Are both lights on and steady? jumpering). Y N

171 178 Bad F2 (Common and language ROS) card. Bad G2 (display) card (see MAP 050 for jumpering). 172 -Probe G2-B09 (+external horizontal drive). 179 Bad D2 (Async Comm-Seriall/O) card. Are both lights on and steady? Y N 180 Bad display assembly (see MIM 204). 173 Check/replace Z3 (display and control panel) Is there a card in A2? cable (see MAP 0210 and MIM 248,249). Y N 181 174 - Remove the A2 (I/O cable driver) card. (Entry Point 0) -Probe G2-B09.

- Disconnect the cable from Z3. Are both lights on and steady? -Probe G2-B09. Y N

Are both lights on and steady? 182 Y N -Reinstall the A2 (I/O cable driver) card. -Press RESTART. Wait 25 seconds.

Go to Step 174, Entry Point O.

01JAN79 1 1 9 9 EC 836600 PEC 835541 B B B B B R STU V MAP 0500-18 B B DISPLAY MAP A B MAP 0500-19 R V 1 W 1 1 C' 8 8 PAGE 19 OF 19

183 190 - Reinstall the A2 (I/O cable driver) card. -Probe H6-E04 (-machine video). - Remove all I/O devices attached to the 5110 (See MIM 248 display Z3 socket locations). I/O interface port (see MIM 271). -Press RESTART. Wait 25 seconds. Are both lights on and steady? -Probe G2-B09. Y N

Are both lights on and steady? 191 Y N Bad BRIGHTNESS control. Check/ replace Z3 (display and control 184 panel) cable (see MAP 0210 and MIM Bad A2 (I/O cable driver) card and cable 248,249). assembly. 192 185 Bad display assembly (see MIM 204). Go to Page 6, Step 053, Entry Point G. Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 248,249). 186 Bad BRIGHTNESS control -Probe G2-B12 (-machine video). 193 Are both lights on and steady? Go to Page 2, Step 013, Entry Point H. '" Y N C/ 187 - Disconnect the cable from Z3. -Probe G2-B12.

Are both lights on and steady? Y N

188 -Connect the Z3 (display and control panel) cable.

Bad G2 (display) card (see MAP 050 for jumpering). c Bad J2 (processor) card (see MAP 050 for jumpering). Bad H2 (base I/O) card.

189 c Bad BRIGHTNESS contro/. Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 248,249).

01JAN79

EC 836600 PEC 835541 B W MAP 0500-19 This page intentionally left blank.

MAP 0500-20 TV MONITOR MAP 0510 C 0 MAP 0510-1 ('

PAGE 1 OF 2

ENTRY POINTS 006

," - Disconnect the TV monitor from the monitor ''',',',", FROM ENTER THIS MAP cable .... (, - Probe the center conductor on the monitor MAP ENTRY PAGE STEP cable connector. NUMBER POINT NUMBER NUMBER Are both lights on and steady? '" 0200 A 001 Y N

( ,./ 007 001 - Remove the monitor cable from the 5110. (Entry Point A) -Probe the center conductor of the 5110 monitor cable connector. - Turn up the BRIGHTNESS control on the TV monitor. Are both lights on and steady? Y N Is there a full raster on the TV monitor? Y N 008 - Remove the jumper 002 Bad TV monitor or its ac input voltage. Bad H2 (base I/O) card. Bad G2 (display) card (see MAP 050 for 003 jumpering). - Turn the BRIGHTNESS control down until the Check/ replace Z3 (display and control white background just disappears. panel) cabie (see MAP 0210 and MIM 248,249). Is there any video on the TV monitor? I Y N 009 -Remove the jumper 004 -Attach a jumper from G2-B12 (-machine Check/ replace machine TV monitor cable video) to G2-B13 (+monitor video). (see MIM 249).

This forces a video signal to the TV monitor. 010 -Remove the jumper. Is there any video on the TV monitor? Y N Bad TV monitor.

005 011 - Disconnect the TV monitor from the machine. Is the 5110 display dark? Y N Is the 5110 display dark? Y N

© Copyright IBM Corp. 1979 01JAN79 EC 836600 PEC 835541 2 2 2 2 ABC 0 E F MAP 0510-1 ABE F TV MONITOR MAP MAP 0510-2 1 1 1 1

PAGE 2 OF 2

012 - Remove the jumper.

Bad TV monitor.

013 - Remove the jumper.

Bad H2 (base I/O) card. Bad G2 (display) card (see MAP 050 for jumpering). Check/replace machine TV monitor cable (see MIM 249).

014 Bad G2 (display) card (see MAP 050 for jumpering).

015 Bad H2 (base I/O) card. Bad G2 (display) card (see MAP 050 for jumpering). Check/ replace machine TV monitor cable (see MIM 249). Bad TV monitor.

01JAN79

EC 836600 PEC 835541

MAP 0510-2 KEYBOARD MAP 0600 MAP 0600-1 (~"-'~I PAGE 1 OF 7

ENTRY POINTS EXIT POINTS FROM ENTER THIS MAP EXIT THIS MAP TO ... (': MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT

0200 A 001 7 077 0420 A ('''11, 0300 A 001 2 006 0700 A _/ 0845 A 001 0900 A 001

001 (Entry Point A)

Can you make the machine fail? Y N

002 (Entry Point B) c Go to the FREELANCE TROUBLESHOOTING GUIDE in the Diagnostic Aids section of the 5110 MIM.

003 Make the machine fail.

Is the PROCESS CHECK light on? Y N

004 • -Calibrate the multimeter (see MIM 270). -For the probe points see MIM 206 and 255. - Measure +8.5 Vdc and +5.0 Vdc at the c' keyboard PC board with referance to N2D08 (gnd) on the A 1 board.

Are both voltages in tolerance (+7.8 Vdc to +9.3 Vdc and +4.6 Vdc to +5.5 Vdc)? Y N

c © Copyright IBM Corp. 1979 01JAN79 EC 836600 PEC 835541 722 ABC MAP 0600-1 B C KEYBOARD MAP F MAP 0600-2 1 1

PAGE 2 OF 7

005 012 - Measure +8.5 Vdc and +5.0 Vdc at the A 1 -Release the P key. board (see MIM 255). -Probe H2-U06 on theA1 board (-interr req 3).

Are both voltages in tolerance (+7.8 Vdc to Is the DOWN light on? +9.3 Vdc and +4.6 Vdc to +5.5 Vdc)? Y N Y N 013 006 -Probe H2-U06 on the A1 board. Go To Map 0700, Entry Point A. -Observe the DOWN light while sequentially pressing keys. 007 Bad keyboard PC board (see MIM 251). Does the DOWN light come on? Check/replace Z4 (keyboard) cable (see Map Y N 0210 and MIM 206,255). 014 008 Bad H2 (base I/O) card. - Press the Q key then the P key. Bad J2 (processor) card (see MAP 050 for jumpering). Did anything (P, Q, *, ?, invalid key, etc) appear on the display? 015 Y N Bad J2 (processor) card (see MAP 050 for jumpering). 009 Bad H2 (base I/O) card. -Probe H2-U12 on the A 1 board (-keyboard Bad CMD key module (see mim 253). strobe). Bad keyboard PC board (see MIM 251). (See appendix B, the general logic probe, in Check/ replace Z4 (keyboard) cable (see Map the 5110 MIM). 0210 and MIM 206,255).

Is the DOWN light on? 016 Y N - Disconnect the keyboard cable at Z4. -Probe H2-U06 (-interrupt req 3). 010 -Probe H2-U12 on the A1 board (-keyboard Is the DOWN light on? strobe). Y N - Press and hold the P key. 017 Is the DOWN light on? Bad keyboard PC board (see MIM 251). Y N Check/ replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255). 011 Bad keyboard PC board (see MIM 251). Check/ replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255).

01JAN79

EC 836600 PEC 835541 3 3 3 o E F G MAP 0600-2 o E G KEYBOARD MAP L MAP 0600-3 222

PAGE 3 OF 7

018 025 -Connect the keyboard cable at Z4. - Press and hold the K key. -Press RESTART. Wait 25 seconds. Bad H2 (base I/O) card. (See BRINGUP HALTS in the Diagnostic Aids Bad J2 (processor) card (see MAP 050 for section of the MIM.) jumpering). Is the machine at halt H? 019 Y N - Remove the keyboard cable at Z4. (see MIM 209). 026 -Probe H2-U12 on the A 1 board (-keyboard -Release the K key. strobe). Did either LOADO or CLEAR WS (spelled Is the UP light on? correctly) appear only once on one and Y N only one line of the 5110 display? Y N 020 - Connect the keyboard cable at Z4. 027 Bad L2 (exec ROS) card (see MAP 050 for Bad H2 (base I/O) card. jumpering).

021 028 -Connect the keyboard cable at Z4. Bad ATTN or HOLD key module c' (See MIM 253). Bad ATTN or HOLD key module Bad keyboard PC board (see MIM 251). (See MIM 253). Check/ replace Z4 (keyboard) cable (see Map Bad keyboard PC board (see MIM 251). 0210 and MIM 206,255). Check/ replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255). 029 -Release the K key. 022 Did QP appear on the display? Do positions 5 and 6 of the second line from Y N the top of the display, contain F3 ? • Y N 023 Did a ? appear on the display? 030 Y N Bad L2 (exec ROS) card (see MAP 050 for jumpering). 024 Did only one character display? 031 Y N Bad CM D key module (See MIM 253). c Bad keyboard PC board (see MIM 251). Check/replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255).

01JAN79 0 ,I: EC 836600 PEC 835541 544 H J K L MAP 0600-3 K KEYBOARD MAP J M MAP 0600-4 3 3

PAGE 4 OF 7

032 036 (Entry Point C) The correct data is coming from the keyboard.

You are checking for keys failing to generate a Bad H2 (base I/O) card. strobe. Bad J2 (processor) card (see MAP 050 for jumpering). -Probe H2-U12 (-keyboard strobe'. Bad G2 (display) card (see MAP 050 for (See appendix B, the general logic probe, in the jumpering). 5110 MIM). Bad L2 (exec ROS) card (see MAP 050 for - Press the failing key. jumpering).

Is the DOWN light on when the key is 037 pressed? -Press and hold the X key. Y N -Press RESTART. - When the machine halts at halt H, release the X 033 key. Bad key module (see MIM 253). Bad keyboard PC board (see MIM 251). Do positions 5 and 6 of the second line from Check/ replace 24 (keyboard) cable (see Map the top of the displ.ay contain C9 ? 0210 and MIM 206,255). Y N

034 038 Using the keyboard data chart (see MIM 250): Do positions 5 and 6 of the second line from the top of display contain C8 ? - Probe the keyboard data bus. Y N H2-Jll 2 H2-M12 1 H2-M08 5 H2-P02 3 039 H2-M09 0 H2-P05 4 Bad keyboard PC board (see MIM 251). H2-Ml0 P H2-U02 6 Check/replace 24 (keyboard) cable (see H2-Ml1 7 Map 0210 and MIM 206,255).

The keycode is represented by bits at an UP 040 level. The keyboard generates a DOWN level Bad left shift key module parity bit if the unused bits of the keycode (See MIM 253). (DOWN level) are even. Bad keyboard PC board (see MIM 251). Check/ replace 24 (keyboard) cable (see Map Is the data correct for the key pressed? 0210 and MIM 206,255). Y N 041 035 Bad right shift key module Bad keyboard PC board (see MIM 251). (See MIM 253). Check/ replace 24 (keyboard) cable (see Map Bad keyboard PC board (see MIM 251). 0210 and MIM 206,255). Check/ replace 24 (keyboard) cable (see Map 0210 and MIM 206,255).

01JAN79

EC 836600 PEe 835541 M MAP 0600-4 H KEYBOARD MAP Q R MAP 0600-5 3 ("' PAGE 5 OF 7

042 049 -Press and hold the P key. Bad L2 (exec ROS) card (see MAP 050 for jumpering). Does the P key perform the repeat function Bad H2 (base I/O) card. (the P key should not preform the repeat Bad J2 (processor) card (see MAP 050 for function)? jumpering). Y N 050 043 Do positions 5 and 6 of the second line from Do both shift keys function? the top of the display contain 03 ? Y N Y N

044 051 Do both shift keys fail? Bad CMD key module Y N (See MIM 253). Bad keyboard PC board (see MIM 251). 045 Check/replace Z4 (keyboard) cable (see Map Bad shift key module 0210 and MIM 206(255). (See MIM 253). Bad keyboard PC board (see MIM 251). 052 Check/ replace Z4 (keyboard) cable (see -Press RESTART. Wait 25 seconds. Map 0210 and MIM 206(255). - Press and hold the space bar.

c' 046 Does the repeat function work? Bad keyboard PC board (see MIM 251). Y N Check/ replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255). 053 - Press and hold the SPACE bar. 047 - Probe H2-B04 (+typamatic). -Press and hold the CMD key. -Press and hold the A key. Is the UP light on? -Press RESTART. Wait 25 seconds. Y N -Release the CMD and the A keys. • 054 Did either LOADO or CLEAR WS (spelled -Probe H2-U12 (-keyboard strobe). correctly) appear only once on one and - Press the space bar. only one line of the 5110 display? Y N Is the DOWN light on when the key is pressed? 048 Y N Is the machine at halt H? (See BRINGUP HALTS in the Diagnostic 055 c Aids section of the M 1M.) Bad key module (see MIM 253). Y N Bad keyboard PC board (see MIM 251). Check/replace Z4(keyboard) cable (see Map 0210 and MIM 206,255).

01JAN79

EC 836600 PEC 835541 7 7 666 N P Q R STU MAP 0600-5 STU KEYBOARD MAP w X MAP 0600-6 555

PAGE 6 OF 7

056 062 - Remove the keyboard cable at Z4. -Press the $ key several times. - Probe H2-B04 (+typamatic). -Press the HOLD key. - Hold the shift key down and press the 8 key Is the DOWN light on? on the numeric keyboard. Y N Did the $ characters on the display change 057 to ¥(yen)? Bad H2 (base I/O) card. Y N

058 063 Bad keyboard PC board (see MIM 251). Bad G2 (display) card (see MAP 050 for Check/ replace Z4 (keyboard) cable (see jumpering). Map 0210 and MIM 206,255). Bad H2 (base I/O) card. Bad keyboard PC board (see MIM 251). 059 Check/ replace Z4 (keyboard) cable (see Bad keyboard PC board (see MIM 251). Map 0210 and MIM 206,255). Check/ replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255). 064 - Press the HOLD key. 060 - Hold the shift key down and press the - Press all the keys one by one. (peroid) key on the numeric keyboard. -Test the ATTN key by pressing the backspace key until a character flashes, then press the Go to Page 1, Step 002, Entry Poin1t B. ATTN key. The flashing character should disappear. 065 - Release the shift and press the $ key several Does any key fail to function? times. Y N -Press the HOLD key. - Hold the shift key down and press the 0 key on 061 the numeric keyboard. -Press ATTN -Press HOLD. Did the $ character change on the display to - Hold the shift key down and press the ¥ (yen)? (peroid) key on the numeric keyboard. Y N This ensures that the 5110 is in EBCDIC character mode. 066 Bad G2 (display) card (see MAP 050 for Now check out the ability of the machine to jumpering). do a character set selection. Bad H2 (base I/O) card. Bad keyboard PC board (see MIM 251). Does the 5110 have the KATAKANA Check/ replace Z4 (keyboard) cable (see Map feature installed? 0210 and MIM 206,255). Y N

01JAN79

EC 836600 PEC 835541 7 7 V WX y MAP 0600-6 N P v y KEYBOARD MAP A Z A A MAP 0600-7 5 566 1 A B

-.~"" ..",, ( / PAGE 7 OF 7

067 074 -Press the HOLD key. Bad H2 (base I/O) card. - Hold the shift key down and press the. (peroid) key on the numeric keyboard. 075 Bad keyboard PC board (see MIM 251). Go to Page 1, Step 002, Check/ replace Z4 (keyboard) cable (see Entry Point B. Map 0210 and MIM 206,255).

068 076 Go to Page 4, Step 032, Entry Point C. Bad H2 (base I/O) card.

069 077 - Press the A key. Go To Map 0420, Entry Point A.

Is an A displayed? Y N

070 Bad key module (see MIM 253).

071 Bad L2 (exec ROS) card (see MAP 050 for jumpering). Bad H2 (base I/O) card. Bad J2 (processor) card (see MAP 050 for jumpering). Bad keyboard PC board (see MIM 251). Check/ replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255).

072 -Probe H2-B04 (+typamatic). (See appendix B, the general logic probe, in the • 5110 MIM).

Is the UP light on? c' Y N 073 -Press and hold the A key -Probe H2-U12 (-keyboard strobe).

Are both lights on and steady? Y N

01JAN79

EC 836600 PEC 835541 A A Z A B MAP 0600-7 , ..• r

This page intentionally left blank.

MAP 0600-8 5110 POWER MAP 0700 ABC MAP 0700-1

(.~~ PAGE 1 OF 6

ENTRY POINTS 005 Plug in the 5110 and I/O devices one at a FROM ENTER THIS MAP time to the customers power. ('h'~t.

~ ;J< .. MAP ENTRY PAGE STEP Does the 5110 or any of the I/O devices NUMBER POINT NUMBER NUMBER cause the customers circuit breakers to trip or their fuses to blow? 0300 A 001 Y N ('~"II 0310 A 001 ~/ 0500 A 001 006 0600 A 001 Suspect customer power problem. 0840 A 001 0841 A 001 007 0843 A 001 The device that caused the customers 0846 A 001 circuit breaker to trip or fuse to blow is bad.

001 See the AC power diagram for the failing (Entry Point A) device:

Is the customers power OK? 5110 (see 5110 MIM 273) Y N 5106 (see 5110 MIM 284) 5103 (see 5103 MIM 384) 002 5114 (see 5114 MIM 182) Is the 5110 or any of the I/O devices causing the bad customer power (take the 008 Y leg if unknown)? Customer power problem Y N 009 003 Is the power supply fan running (see MIM Customer power problem 202 and 273)? Y N 004 Unplug the 5110 and all the I/O devices from 010 the customer power. Is fuse F1 blown? Have the customer reset their circuit breaker (See MIM 207 and 273). c or replace their fuse. Y N • Does the customers circuit breakers trip or 011 their fuses still blow? Is the line cord plugged in? Y N (See MIM 273). Y N

012 Plug the line cord in.

© Copyright IBM Corp. 1979 01JAN79

EC 836600 PEC 835541 322 ABC o E F MAP 0700-1 E F 5110 POWER MAP J MAP 0700-2 1 1 / ."

PAGE 2 OF 6

013 018 -Power down. - Power down. -Connect the ac power cable at J3 (see MIM Check for: 273). 1. Open line cord (see MIM 273). - Power up. Wait 25 seconds. 2. Open power switch (see MIM 273). 3. Open ac power filters (see MIM 273). Does fuse F1 blow now? 4. Open in ac power box (see MIM 273). Y N 5. Open fan lead J2 (see MIM273). 6. Open fan motor winding (see MIM 273). 019 -Power down. 014 -Connect the ac power cable at J1 (see MIM - Power down. 273). -Replace fuse Fl. - Power up. Wait 25 seconds. - Power up. Wait 25 seconds. Does fuse F1 blow now? Does fuse F1 blow after replacing? Y N Y N 020 015 Trouble was probaly a bad cable Bad fuse Fl connection at Jl or J2 or J3.

016 021 -Power down. -Power down. - Replace fuse F1 - Replace the fuse F1. -Disconnect the ac power cables at J1, J2, and - Disconnect the dc power cable at A 1Y1 (see J3 (see MIM 273). MIM 272). -Power up. Wait 25 seconds. - Power up. Wait 25 seconds.

Does fuse F1 blow now? Does fuse F1 blow now? Y N V N

017 022 - Power down. -Measure the UNLOADED voltages at the -Connect the ac power cable at J2 (see MIM dc power cable (see MIM 272). 273). - Power up. Wait 25 seconds. Are all the voltages in tolerance? V N Does fuse F1 blow now? Y N

01JAN79

EC 836600 PEC 835541 3 3 3 333 G H J K L M N MAP 0700-2 G H K L M N 5110 POWER MAP o MAP 0700-3 222 2 2 2 1

PAGE 3 OF 6

023 029 Check/ replace A 1Y1 (DC Power) -Calibrate the multimeter (see MIM 270). ''''"~ ~ ( cable (see MIM 272). - Measure the following loaded voltages at the A 1 ...... v Bad power supply. board to C1-A13 (gnd): ************* - Record the pin location of any voltages that are * CAUTION * out of tolerance (see MIM 272). ************* see MIM 271, power supply +5 Vdc A1-D13 removal and replacement. +8.5 Vdc C1-C11 +12VdcC1-D13 024 -12VdcC1-E13 Go to Page 4, Step 038, -5 Vdc C1-E11 Entry Point B. Are all voltages in tolerance? 025 Y N Bad power supply. Check/replace A 1Y1 (DC Power) cable 030 (see MIM 272). - Power down. ************* - Disconnect the cable at the I/O interface port * CAUTION * if installed (see MIM 283). ************* - Disconnect the dc power cable at Y1 (see see MIM 271, power supply removal MIM 272). and replacement. -Power up. -Measure the UNLOADED voltages at the dc 026 power cable (see MIM 272). Bad tape motor assembly (see MIM 203). Bad tape fan assmbly. Are all voltages in tolerance? Y N 027 Bad fan assembly. 031 Is there any voltage present? 028 Y N Check for a short or loose connection in the ac power box (see MIM 273). 032 - Power down. - Exchange the power supply connector J1 with the fan connector, J2. (See MIM 273). - Power up. Wait 25 seconds.

Is the fan running now? Y N

01JAN79

EC 836600 PEe 835541 6 4 4 4 4 P Q R S T MAP 0700-3 R S T 5110 POWER MAP MAP 0700-4 333

PAGE 4 OF 6

033 038 Swap cables J1 and J2 back to their (Entry Point B) original positions. Check/replace the cables in the ac power -Power down. box (see MIM 273). -Connect the de cable back into socket Y1. -Power up. 034 - Measure the following LOADED voltages to Are the voltages present now? C1-A 13 (gnd) for the next several steps (see Y N MIM 272). +5 Vdc A1-D13 035 +8.5 Vdc C1-C11 Swap cables J1 and J2 back to their +12 Vdc C1-D13 original positions. -12 Vdc C1-E13 Check/ replace A 1Y1 (DC Power) cable -5 Vdc C1-E11 (see MIM 272). Bad pow~r supply. Does the fuse F1 blow or are any of the ************* measured voltages out of tolerance? * CAUTION * V N ************* see M I M 271, power supply removal and 039 replacement. Go to Page 5, Step 047, Entry Point D.

036 040 Swap cables J 1 and J2 back to their orignal -Power down. positions. - Remove all the cards from the board. A cable was unseated or had an open - Replace fuse F1 if needed. connection. Inspect for loose connections. (see MIM 209). - Power up. Wait 25 seconds. 037 Check/replace A1Y1 (DC Power) cable (see MIM Does fuse F1 blow or does power drop or is 272). the voltage out of tolerance now? Bad power supply. V N ************* * CAUTION * 041 ************* Bad card. see MIM 271, power supply removal and Power down and power up as you reinstall the replacement. cards one at a time until the defective card is found.

01JAN79

EC 836600 PEC 835541 5 U MAP 0700-4 U 5110 POWER MAP A MAP 0700-5 4 A (-' PAGE 5 OF 6

042 047 -Power down. (Entry Point D) (.~ - Replace fuse F1 if needed. - Disconnect all the cables to the A 1 board except -Connect the I/O interface cable to the 5110. the dc power cable at Y1 (see MIM 209). - Power up. Wait 25 seconds. Does the fuse F1 blow or are any of the measured voltages out of tolerance? Does the fuse F1 blow or are any of the V N

.."... "" measured voltages out of tolerance?

( _.// V N 048 The problem was corrected by reseating the 043 cables. Inspect both ends of the cables for -Connect the Z4 (keyboard) cable. loose foreign conductors (foil or wire ends for example). Does the fuse F1 blow or are any of the measured voltages out of tolerance? 049 V N - Disconnect all the I/O interface cables from each other and from the 5110 I/O interface port. 044 -Connect the I/O devices one at a time to the -Connect the Z2 (tape) cable. Ranger I/O interface port. - Measure all the voltages again for each device Does the fuse F1 blow or are any of the you attach. Ct measured voltages out of tolerance? V N The device which causes a voltage to be out of tolerance, or blows a fuse, is the bad device. 045 - Remove all the cards from that device. -Connect the Z3 (display and control - Power up. Wait 25 seconds. panel) cable. Does the fuse F1 blow or are any of the Does the fuse F1 blow or are any of measured voltages out of tolerance? the measured voltages out of V N tolerance? V N 050 One of the cards removed is defective. 046 Reinstall them one at a time until the -Connect the Z1 (ASYNC COM-Serial measured voltage goes out of tolerance. The I/O) cable. last card reinstalled is defective.

Does the fuse F1 blow or are any 051 of the measured voltages out of Bad external I/O device or cable. Check tolerance? especially for short circuits (see MAP 0210). c V N

01JAN79

EC 836600 PEC 835541 6 6 6 6 6 A V WX Y Z A MAP 0700-5

I "'.'·_"'··~'I_~ .. ·n"~,,~ •. ~ "~'.'.'!! .,."." ,. '~':''''3C'..,....,.,.-c::~"or. ·, ....".".~.-. __'_L ~ ..... _ .... ~,.~_~ ___ •• ______•••. ______.__ ._~ __ x y Z 5110 POWER MAP p V W MAP 0700-6 555 355

PAGE 6 OF 6

052 059 - Power down. - Power down. - Disconnect the communication cable at - Disconnect keyboard cable at the the data set and / or the serial I/O cable keyboard. from the serial I/O device. (See MIM 206). -Power up. -Power up.

Does the fuse F1 blow or are any of the Does the fuse F1 blow or are any of the measured voltages out of tolerance? measured voltages out of tolerance? /- ''\ Y N Y N

053 060 Bad data set or serial I/O device. Short circuit in the keyboard PC board. (See MIM 251). 054 Short circuit in the communication cable or 061 serial I/O cable. Bad keyboard cable. (See MIM 206). 055 -Power down. 062 - Disconnect the cable connector on the 5110 Bad A 1 board. display. -Power up. 063 The power supply is working properly. Does the fuse F1 blow or are any of the measured voltages out of tolerance? Are you missing a voltage at a specific Y N device? Y N 056 Bad display assembly (see MIM 204). 064 ************* Bad A 1 board. * CAUTION * ************* 065 High voltage is present. Trace the circuit from that device to the power supply (see MIM 274 and LOGIC diagram 480). 057 -Check for a short circuit in the control panel switches. (See MIM 248,249, display and control panel cable).

058 Check for a short circuit in the tape unit. Bad tape control card (see MIM 203). Short circuit in the internal tape cable.

01JAN79

EC 836600 PEC 835541

MAP 0700-6

------t..:---- -.-----.-~--.'"~. -.--- .... ----.------PRINTER MAP MAP 0810-1

PAGE 1 OF 4

ENTRY POINTS EXIT POINTS

"""',1> FROM ENTER THIS MAP EXIT THIS MAP TO

( / . - MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT

0200 A 001 2 008 0420 A

001 (Entry Point A)

This is the entry MAP for the 5103.

Information on the use of the CE probe can be found in Appendix B of the 5110 MIM.

Is the PROCESS CHECK light on1 Y N

002

c· Does the 5110 have an internal tape drive (see MIM 201)1 Y N

003

Is a second 5114 installed on the system 1 Y N

004 NOTE: a problem in the 5114 I/O " interface cable, the 5114 adapter card, C, /v or 5114 cables D1 or D3 can also cause a problem in the printer. Go to Page 3, Step 010, Entry Point C.

© Copyright IBM Corp. 1979 01JAN79

EC 836600 PEC 835541 222 ABC MAP 0810-1 ABC PRINTER MAP MAP 0810-2 111

PAGE 2 OF 4

(Step 009 continued) 005 -Wait for MDI OPTIONS to be displayed. Disconnect the second 5114. Connect the -Advance the cursor to STEP NO. 5103 to the first 5114. - Enter the three-digit step no. recorded earlier. -Press EXECUTE NOTE: a problem in the 5114 I/O interface cable, the 5114 adapter card, or 5114 The printer MDI is now continuing at the step cables D1 or D3 can also cause a problem where the PROCESS CHECK light occured in the printer. before. Follow the instructions on the display. /' '\ Go to Page 3, Step 010, Entry Point C.

006 If there is a 5106 and / or 5114(s) attached, disconnect the 5106 and the 5114(s). Connect the 5103 directly to the 5110. Go to Page 3, Step 010, Entry Point C.

007 Is the printer MOl loaded? Y N

008 Go To Map 0420, Entry Point A.

009 This procedure will reset the process check and let you continue with the printer MDI at the map number and step number on the display.

- Record the map number and step number now displayed. -Press and release the RESTART switch. Wait 25 seconds. Use the keys on the numeric section of the keyboard: -Hold CMD and press HOLD -Hold CMD and press - (minus) -For BASIC, hold CMD and press * (multiply) -For APL, hold CMD and press x (multiply) -Press C -Press 1 - Press EXECUTE Follow the instructions on the display until DSP MENU appears. Then enter the rightmost three digits of the map no. recorded earlier. - Press 0 (alphabetic) -Press EXECUTE (Step 009 ~ontinues)

01JAN79 / EC 836600 PEC 835541

MAP 0810-2 PRINTER MAP o MAP 0810-3 (~ PAGE 3 OF 4

010 014 (Entry Point C) Did you disconnect a 5106 and/or a 5114(s) from the 5110 to run this MDI? -If a PROCESS CH ECK occurs after doing the Y N following, GO TO MAP 420, Entry Point A. 015 -Press RESTART. WAIT 25 seconds. (Entry Point B) Use the keys on the numeric keyboard. -Press HOLD -Press RESTART. Wait 25 seconds. -Hold CMD and press - (minus) -For BASIC, hold CMD and press *(multiply) Did the customer complain of trouble with -For APL, hold CMD and press x (multiply) PRINT/PLOT? -Press C Y N -Press 1 - Press EXECUTE 016 No trouble found. Do the words TAPE READ DIAGNOSTIC or DISKETTE READ DIAGNOSTIC appear on the 017 top line of the display? -Remove the 5103 tractor assembly. Y N -Install 1 part paper. -Set the paper release lever to the rear of the 011 machine (see 5103 MIM 301). Bad F2 (Common and language ROS) card. -Set the copy control dial to 1 (see 5103 MIM 301). 012 -Insert the PRINT/PLOT tape cartridge or - Follow the instructions on the display until DSP diskette that IBM supplied to the customer. MENU appears. THEN: For APL, enter: -Enter 800 )LlNK 1 - Press EXECUTE -Press EXECUTE

The printer MDI should now load and run. For BASIC, enter: If a PROCESS CHECK occurs, Go To Map 0420, LINK 1 Entry Point A. - Press EXECUTE Follow the instructions on the display. Return to this step if the M DI directs you to The answers to the questions on the display return to MAP 0810. are as follows: 1 or 2 Press EXECUTE Did the MDI run to completion? 1 Press EXECUTE Y N 2 Press EXECUTE • 2 Press EXECUTE 013 o Follow the instructions on the display. When LOADO or CLEAR WS is displayed, enter the following information:

For APL, enter (Step 017 continues)

01JAN79

EC 836600 PEC 835541 4 o E MAP 0810-3 PRINTER MAP E MAP 0810-4 3

PAGE 4 OF 4

(Step 017 continued) )LOAO 4 022 - Press EXECUTE. -Reconnect the 5106 or the 5114 to the 5110 -Enter )RUN one at a time. - Press EXECUTE. -Connect the 5103 to the 5106 or to the 5114. -Rerun the printer MOl 0800. For BASIC, enter LOAO 5 00 NOT FOLLOW THE PRINTER MOl IF AN - Press EXECUTE ERROR OCCURS. -Enter RUN - Press EXECUTE. Did MDI 0800 run to completion? V N Are the dots within the tolerance lines? V N 023 The problem is in the 5106 if attached, or in 018 the 5114. Go to MAP 0850 if you have a Check the platen pressure roll adjustment (see 5106 attached or go to MAP 0880 if you have 5103 MIM 323). a 5114. If the above procedure does not find Check for loose or broken parts in the paper the problem, suspect the I/O interface cables path. in either the 5106 or in the 5114 (see MAP .Bad forms feed stepper motor. 0210 and MIM 213) and cables 01 and 03 in Bad A1 B1 (motor driver) card (see 5103 MIM the 5114, or cables B1 and B2 in the 5106 303). (see MAP 0210 and MIM 280), or the adaptor Bad A 1A 1 (sense amplifier) cards (C1) in the 5106 or the 5114(s). Check the platen gear backlash. Check the forms feed stepper motor/emitter 024 timing (see 5103 MIM 332). Go to Page 3, Step 015, Entry Point B.

019 Are the verticle lines the correct length and density? V N

020 Check the forms feed stepper motor/emitter timing (see 5103 MIM 332). This is a very critical adjustment for Print/ plot. It may be necessary to fine adjust the emitter so that the Print/ plot graph verticle lines are the same length and height. Bad A1A1 (sense amplifier) card (see 5103

MIM 303). / ,

021 PRINT /PLOT mechanical functions check out OK

01JAN79

EC 836600 PEC 835541

MAP 0810-4 COMMUNICATIONS,SERIAL I/O, MAP 0830-1 (' AND PARALLEL I/O MAP 0830 PAGE 1 OF 4

ENTRY POINTS EXIT POINTS

I, ('~ 'I FROM ENTER THIS MAP EXIT THIS MAP TO

/ MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT

0200 A 001 2 009 0300 A (:'~, 4 031 0420 A 2 012 0420 A 2 010 0420 A

001 (Entry Point A)

This is the entry MAP for the asynchronous communications (async comm), binary synchronous communications (BSC), serial I/O, and parallel I/O adapters. Load these MDls from the communications diagnostic cartridge if the 5110 has an internal tape drive, otherwise use the diagnostic diskette. If the PROCESS CHECK light is on, the MDI cannot be loaded.

Is the PROCESS CHECK light on1 Y N

002 Is the problem 99XX error codes when the user loads the esc feature microcode 1 Y N

003 Do you want to test the esc feature 1 c' Y N c'

© Copyright IBM Corp. 1979 01JAN79

EC 836600 PEC 835541 433 2 ABC 0 MAP 0830-1

I o COMMUNICATIONS, E F MAP 0830-2 1 SIO AND PIO MAP

PAGE 2 OF 4

004 011 (Entry Point B) -Enter the desired MDI number. - Press EXECUTE. Use the keys on the numeric section of the keyboard: The MDI should load and run. If a PROCESS CHECK occurs while the MDI is running go to -Press HOLD MAP 0420, otherwise follow the instructions -Hold CMD and press - (minus) on the display. -For BASIC, hold CMD and press * (multiply) When completed, return to BASIC/ APL -For APL,hoid CMD and press X (multiply) mode by pressing RESTART. -Press C -Press 1 012 -Press EXECUTE Go To Map 0420, Entry Point A.

Did the PROCESS CHECK light come on? Y N

005 Do the words TAPE READ DIAGNOSTIC or DISKETTE READ DIAGNOSTIC appear on the top line of the display? Y N

006 Bad F2 (Common and language ROS) card.

007 You have loaded and are running the read diagnostic program (see section 4, diagnostic aids). Foilow the instructions on the display. Return to. this point for further instructions when the DSP MENU is displayed.

Is the DSP MENU on the display? Y N

008 Is the PROCESS CHECK light on? Y N

009 Go To Map 0300, Entry Point A.

010 Go To Map 0420, Entry Point A.

01JAN79

EC 836600 PEC 835541 E F MAP 0830-2 C COMMUNICATIONS, B MAP 0830-3 1 1 SIO AND PIO MAP

PAGE 3 OF 4

(Step 013 continued) 013 World Trade except Canada) The BSCA diagnostics require some information about the communication facility card. Indicate NOTE - If this is the first CE call on the BSCA on the following list which communication facility feature, verify that the CTS delay and the echo is installed so you can accurately answer the clamp are compatable with the remote questions. asked by the diagnostic. On the first station(s). If help is needed to determine CE call (assume the first CE call if none of the compatability, contact the local BODS. following communication facilities has been Also verify that the transmit level is correct indicated), unplug the C2 card and refer to the (see MAP 0831) then return here to continue. BSC MIM to determine which communication Go to Page 2, Step 004, Entry Point B. facility card is installed and how it is personalized. 014 NOTE- BSC problems after the A 1 board has Was the error code 99007 been replaced may be caused by wrong nets on Y N the new A 1 board. See the A 1 Board Requirements in the BSC MIM. 015 Was the error code 9921 , 9940 or 99417 () EIA Y N

( ) DDSA - (U.S. only) - 2400 bps 016 Was the error code 9931 or 99327 c ( ) DDSA - (U.S. only) - 4800 bps Y N ( ) 38LS - switched - 017 Was the error code 9933, 9970, 9971, transmit level = ____db 9972, 9974, 9975, 9976, 9977, 9981, 9982 or 99997 Equalizer switch set ON (Only Y N World Trade except Canada) 018 ( ) 38LS - nonswitched - Was the error code 99837 Y N ( )2 wire ( )4 wire

( )30 ms CTS delay, 0 ms echo clamp c' ( )80 ms CTS delay, 50 ms echo clamp

( )230 ms CTS delay, 150 ms echo clamp

'""" co 0 M_M M ( )SNBU transmit level = ____db co co co 000 c ()Transmit level (Only World Trade except Canada) = db

Equalizer switch set ON (Only (Step 013 continues) " .. _,. 01JAN79 ( / EC 836600 PEC 835541 4 4 4 444 G H J K L M MAP 0830-3

, .l K L M COMMUNICATIONS, A G H J MAP 0830-4 333 1 3 3 3 SIO AND PIO MAP

PAGE 40F 4

019 028 Was the error code 9987 or 99981 Bad B2 (BSCA 1) card. Y N Bad BSCA microprocessor module (located on the B2 card). 020 When replacing the module, position it Was the error code 99861 so the notch in the narrow end is Y N pointed towards the cylinder shaped module. 021 Bad B2 (BSCA 1) card. 029 Bad B2 (BSCA 1) card. 022 Bad H2 (base I/O) card. Bad C2 (38LS) card. See the BSC M I M for jumpering and 030 switch setting instructions. BSC program problem. Suspect the BSC cartridge or diskette. 023 -Unplug the BSCA external cable from the 031 5110. Go To Map 0420, Entry Point A. - Reload the BSC microcode.

Does error 9987 or 9998 occur while reloading the BSC microcode 1 Y N

024 Connect the BSCA external cable to the 5110, then run MOl 0821 (see step 004). If MOl 821 runs OK (no errors), then suspect a problem at the remote station.

025 Bad C2 (EIA,OOSA,38LS) card. Bad A4 (BSCA 2) card. See the BSC M I M for jumpering and switch setting instructions.

026 Bad A4 (BSCA 2) card.

027 Bad A4 (BSCA 2) card. Bad B2 (BSCA 1) card.

01JAN79.

EC 836600 PEC 835541

MAP 0830-4 Transmit and Receive Level A MAP 0831-1 Checkout MAP

PAGE 1 OF 6

001 005 (Entry Point A) - Dial the local modem telephone from a nearby telephone. After you hear the ring, the 3 Use this MAP to check the modem transmit or second answer tone and some SYN characters, receive level or to set the transmit level for an cradle the telephone handset. IBM modem. Go to Page 2, Step 006, Entry Point F.

Is the local station on a switched telephone network or does it have Switched Network Back Up (SNBU) installed? Y N

002 Go to Page 4, Step 020, Entry Point B.

003 This is the transmit level procedure for a switched network. - Connect the DB meter to the DT (DATA TIP) and DR (DATA RING) terminals at the coupler. - Set the DB meter to the bridge position. - Load the Communications Diagnostic Cartridge or the 5110 Diagnostic Diskette. Select the BSCA Test Patterns by entering 898 when the DSP MENU is displayed. DO NOT enter 0 to select the option menu at this time. - Follow the instructions on the display. Select STEP mode and select step 8 to transmit continuous SYN characters. Answer Y for business machine clocking if the local station has a 38LS installed. Answer the other questions based on the local station configuration.

Does this station have Auto Answer? Y N

004 - Dial the local modem telephone from a nearby telephone. Answer the modem telephone and put it DATA mode. Go to Page 2, Step 006, Entry Point F.

© Copyright IBM Corp. 1979 01JAN79

EC 836600 PEC 835541

A MAP 0831-1

I ,. Transmit / Receive level BCD E MAP 0831-2 Checkout Map

PAGE 2 OF 6

006 009 (Entry Point F) Modem problem. Reconnect the white wire to DT and the black wire to DR at the coupler. When the terminal begins to transmit, does the DB meter indicate the value marked on If using an OEM modem, have the the coupler within a tolerance of one db for at customer notify the responsible person. least 10 seconds? Y N If using an IBM external modem, use the maintenance information provided with 007 that modem. - Set the modem transmit level to the db level specified on the coupler. If the db value is Bad C2 (38LS) card. not specified, have the customer notify the telephone company. (NOTE- Some couplers 010 have an automatic transmit level setting Coupler problem. Reconnect the white feature. If this type of coupler is installed, wire to DT and the black wire to DR at the ask the customer what db level it requires.) coupler. See the BSC M I M for the procedure to set the transmit level for a 38LS integrated Have the customer notify the responsible modem. For IBM external modems, use the person. maintenance information provided with the external modem. 011 The transmit level is correct. Does the DB meter indicate the correct level now? Do you want to check the receive level? Y N Y N

008 012 - Disconnect the meter leads from the DT The test is complete. If you tested SNBU and DR terminals. and want to test the nonswitched - Disconnect the DT and DR leads from the transmit/ receive levels, go to Step 020 coupler that go to the modem. Entry Point B. - Set the db meter switch to the 600 position. 013 - Connect the DB meter to the white (DT) Go to Page 3, Step 017, Entry Point C. and black (DR) wires just disconnected. 014 Does the DB meter indicate the correct The transmit level is correct. value now? Y N Do you want to check the receive level? Y N

01JAN79

EC 836600 PEC 835541 3 3 BCD E F G MAP 0831-2

t F G Transmit / Receive Level MAP 0831-3 2 2 Checkout Map (""-~ PAGE 3 OF 6

015 017 The test is complete. If you tested SNBU and (Entry Point C) want to test the nonswitched transmit/ receive '" -. ( levels, go to Step 020, Entry Point B. This is the receive level procedure for a switched network. 016 - Set the DB meter range for -30 db. Go to Step 017, Entry Point C. - Have the remote station transmit a pattern.

Is the receive level correct? (U.S. should be between -21.5 and -27.2 db. In World Trade, c consult the local PTT representative.) Y N

018 Telephone network problem. Have the customer notify the responsible person.

019 The receive level is OK. Test complete. If you tested SNBU and want to test the nonswitched transmit/ receive levels, go to Step 020, Entry Point B.

'" ( j

01JAN79 c EC 836600 PEC 835541 MAP 0831-3 Transmit / Receive Level L MAP 0831-4 Checkout Map PAGE 4 OF 6

020 023 (Entry Point B) (Entry Point E)

This is the transmit level procedure for a - Set the transmit level to the correct level. See nonswitched network. the BSC M I M for 38LS switch settings. The transmit level for U.S. and Canadian nonswitched networks is 0 db. For World Trade If using an IBM external modem, use the countries (except Canada), consult the local PTT maintenance information provided with that representative for the correct transmit level. modem. If using an .OEM modem, have the customer - Set the DB meter to the bridge position. notify the responsible person. - Take the cover off the 4 prong connector to the telephone line. Connect the DB meter to the R . Does the DB meter indicate the correct level and G N terminals inside the plug. now? - Load the communications diagnostic cartridge V N or the 5110 diagnostic diskette. Select the BSCA test patterns by entering 898 when the 024 DSP MENU is displayed. DO NOT enter 0 to - Unplug the external cable from the select the option menu at this time. nonswitched telephone line. - Follow the instructions on the display. Select - Set the DB meter to the 600 position. step mode and select step 008 to transmit continuous SYN characters. NOTE: If the local Does the DB meter indicate the correct db station is on a multipoint network, go to Entry level now? Point E. V N

Is the transmit level correct? 025 V N modem problem.

021 If using an OEM modem, have the Is the local station using a World Trade customer notify the responsible perSOD. (except Canada) 38LS? V N If using an IBM external modem, use the maintenance information provided with 022 that modem. Is the local station using a U.S./Canada 38LS? Bad C2 (38LS) card. V N 026 Telephone network problem. Have the customer notify the responsible person.

If .. 01JAN79

EC 836600 PEC 835541 555 5 H J K L M MAP 0831-4 H J K M Transmit / Receive level MAP 0831-5 4 4 4 4 ( Checkout Map PAGE 5 OF 6

027 035 The transmit level is OK. (Entry Point D)

Do you want to check the receive This is the receive level procedure for a level? nonswitched network. V N - Set the DB meter to the bridge position. - Connect the DB meter leads to the Rand GN 028 terminals in the 4 prong plug for a 2 wire Test complete. If SNBU is installed network. For a 4 wire network, connect the and you want to test its leads to the Y and BK terminals. transmit/ receive levels, go to Step - Have the remote station transmit a pattern. 003. ) Is the receive level correct? (U.S. should be 029 between -15 and -17 db. In World Trade, Go to Step 035, consult the local PTT representative) Entry Point D. Y N

030 036 Bad C2 (38LS) card. Have the remote station verify that their transmit level is correct. 031 Go to Page 4, Step 023, Entry Point E. Telephone network problem. Have the customer notify the responsible 032 person. The transmit level is OK. 037 Do you want to check the receive level? Is the 5110 on a 4 wire nonswitched Y N network? Y N 033 Test complete. If SNBU is installed and you 038 want to test its transmit/ receive levels, go to The receive level test is OK. If SNBU is Step 003. installed and you want to test its transmit/receive levels, go to Step 003. 034 Go to Step 035, Entry Point D. 039 (:: To check the internal and external cables, connect the DB meter to C2G09 and C2J13 (See logic diagram 455).

Is the receive level correct? c Y N

01JAN79 c EC 836600 PEC 835541 6 6 N P MAP 0831-5 N P Transmit / Receive Level MAP 0831-6 5 5 Checkout Map

PAGE 6 OF 6

040 Bad external cable. Bad internal cable. See logic diagram 455.

041 Receive level test is OK. If SNBU is installed and you want to test its transmit/ receive levels, go to step 003. If receive problems still occur, replace the C2 (38LS) card.

01JAN79

EC 836600 PEC 835541

MAP 0831-6 Local CBS type coupler MAP 0832-1 (Auto Answer) MAP for 38LS

PAGE 1 OF 7

001 Use this MAP to isolate problems to the local *** COLOR CODE CHART *** 38LS integrated modem or local CBS type ('" coupler by using a nearby telephone. Switch Hook (SH) = Red Signal Ground (SG) = Grey - Verify that the connections from the modem to Data Modem Ready (DA) = Yellow the coupler are correct (see color code chart). Coupler Cut Through (CCT) = Brown - Make DATA TERMINAL READY (DTR) inactive Off Hook (OH) = Blue by pressing the RESTART key. Ring Indicate (RI) = Violet - Select the 15 VDC range on the CE meter. Data Tip (DT) =White - The MAP will state which CE meter lead to Data Ring (DR) = Black probe the signal to be measured. At that time, connect the other lead to SG (SIGNAL GROUND) if probing at the coupler or to C2D08 NOTE - The inactive level of all the above coupler if probing on the C2 (38LS) card. connections except DT and DR are - EIA levels - Lift the modem telephone handset from the (-3 to - 25 VDC) when measured to SG. cradle. DO NOT lift the exclusion key. - Listen for the dial tone.

Do you hear the dial tone? V N

002 c - Lift the exclusion key.

Do you hear the dial tone now? V N

003 Telephone problem. Go to Page 4, Step 034, Entry Point A.

004 - Dial a nearby telephone.

Can calls be completed like an ordinary telephone? V N

005 Telephone problem. Go to Page 4, Step 034, Entry Point A.

© Copyright IBM Corp. 1979 01JAN79

EC 836600 PEC 835541 4 2 A B MAP 0832-1 B Local CBS coupler MAP C 0 MAP 0832-2 1 for 38LS

PAGE 2 OF 7

006 011 - The modem telephone tests OK as an ordinary Line disconnected. telephone. Suspect the test pattern stopped or a wrong procedure. Restart this MAP. To test the Auto Answer function, make DTR active by: Suspect the C2 (38LS) card. 1. Load the communications diagnostic cartridge or 5110 diagnostic diskette. 012 2. Enter 898 to select the BSCA Test Patterns The Auto Answer function tested OK. Check for when the DSP MENU is displayed. DO NOT disconnect operating correctly by: enter 0 to select the option menu at this time. 1 . Lift the handset on the local modem 3. Select STEP mode and step 8 to transmit telephone. This should disconnect the line and continuous SYN characters. display a N on the reply line of the MOl display. 4. Select Y for the Business Machine option. 2. Listen at the telephone that originated the call Answer the other questions based on the local for the data transmission to stop. station configuration. 3. Listen for dial tone approximately 20 seconds - Dial the local modem telephone from a nearby after the data stopped. telephone. - Listen for a high pitched tone (answer tone) that Do you hear the dial tone 1 lasts for approximately 3 seconds. Y N

Do you hear the answer tone 1 013 Y N - Cradle the modem telephone handset. - Probe the SH (Red) terminal at the coupler 007 with the - meter lead. Cradle the handset on the nearby telephone. Go to Page 5, Step 043, Entry Point B. Is SH at a • EIA level (·3 to ·25 VDC)1 Y N 008 Do you hear the data (SYN characters) after 014 the answer tone 1 Telephone problem. Y N Have the customer notify the responsible person. 009 Do you hear the dial tone approximately 20 015 seconds after the answer tone stops 1 - Lift the modem telephone handset from the Y N cradle.

010 Does SH go to a + EIA level (+3 to +25 Bad C2 (38LS) card. VDC)1 See the BSC MIM for jumpering and Y N switch setting instructions. 016 Telephone problem. Have the customer notify the responsible person.

01JAN79

EC 836600 PEC 835541 3 3 C D E F MAP 0832-2 E F Local CBS coupler MAP G H MAP 0832-3 2 2 for 38LS PAGE 3 OF 7

017 025 - Probe C2G10 (SWITCH HOOK) with the + - Make Data Terminal Ready (DTR) active by meter lead. using MOl 898 step 008 to transmit continuous SYN characters. Is SWITCH HOOK at a + EIA level (+3 to - Put the modem telephone handset back in +25VDC)? the cradle. Y N Does the nearby telephone hear 018 approximately 3 seconds of answer tone c Cable problem. followed by continuous SYN characters? See logic diagram 455. Y N

019 026 Bad C2 (38LS) card. Bad C2 (38LS) card. See the BSC MIM for jumpering and switch See the BSC M I M for jumpering and setting instructions. switch setting instructions.

020 027 - The disconnect function tested OK. The manual answer function tested OK.

Do you want to test the manual answer 028 function? - Put the external modem in talk mode. Y N - Have someone dial the local modem telephone from a nearby telephone. 021 - After the modem telephone rings, lift the The CBS type coupler tested OK. handset from the cradle. - Lift the exclusion key. 022 Does the local station have an external Can you talk with the other person? modem? Y N Y N 029 023 Telephone problem. - Have someone dial the local modem Have the customer notify the responsible telephone from a nearby telephone. person. - After the modem telephone rings, lift the handset and lift the exclusion key.

Can you talk with the other person? Y N

024 telephone problem . C./: Have the customer notify the responsible person.

01JAN79 c EC 836600 PEC 835541 4 G H J MAP 0832-3 A J Local CBS coupler MAP MAP 0832-4 1 3 for 38LS

PAGE 4 OF 7

030 034 - Put the modem in OATA mode. (Entry Point A) - Make Oata Terminal Ready (OTR) active by using MOl 898 step 008 to transmit - Cradle the modem telephone handset. continuous SYN characters. - Probe the SH (Red) terminal at the coupler with - Put the modem telephone handset back in the - meter lead. the cradle. Is SH at a - EIA level (-3 to -25 VDC)? Does the nearby telephone hear Y N approximately 3 seconds of answer tone and the continuous SYN characters? 035 Y N - Probe the SH (Red) terminal at the coupler with the + meter lead. 031 Modem problem. Is SH at a + EIA level (+3 to +25 VDC)? If using an OEM modem, have the Y N customer notify the responsible person. 036 If using an IBM external modem, use the Coupler power is bad. maintenance information provided with Have the customer notify the responsible that modem. person.

032 037 The manual answer function tested OK. - Lift the modem telephone handset from the cradle. 033 Exclusion key is not wired properly in the Does SH go to a - EIA level (-3 to -25 VDC)? telephone set. Y N Have the customer notify the responsible person. 038 Coupler or cradle switch problem. Have the customer notify the responsible person.

039 Cradle switch wired backwards in the telephone set. Have the customer notify the responsible person.

01JAN79

EC 836600 PEC 835541 5 K MAP 0832-4 K Local CBS coupler MAP MAP 0832-5 4 ( for 38LS PAGE 5 OF 7

040 043 - Lift the modem telephone handset from the (Entry Point B) ··'·'.·'" "', cradle. . C-- Does the CBS type coupler have a test Does SH go to a + EIA level (+3 to +25 VDC)? switch? Y N Y N

041 044 Cradle switch not wired to coupler. Go to Step 047, Entry Point C. Have the customer notify the responsible person. 045 Is the test switch set to the operate mode 042 (non-test) position? Telephone problem. Y N Have the customer notify the responsible person. 046 Set the switch to the operate mode position, then restart this MAP.

047 (Entry Point C)

Is the modem telephone handset cradled? V N

048 Cradle the handset and restart.

049 Did the telephone ring only once? Y N

050 - Make DTR inactive by pressing the ATTN key once. - Dial the modem telephone from a nearby telephone.

Does the modem telephone ring? Y N

051 c Telephone problem. Have the customer notify the responsible person.

c\ 01JAN79 EC '836600 PEC 835541 7 6 L M MAP 0832-5 M Local CBS coupler MAP N P MAP 0832-6 5 for 38LS PAGE 6 OF 7

052 057 - Let the modem telephone ring for this step. - Probe C2G03 (OFF HOOK) with the + meter - Probe the RI (Violet) terminal at the coupler lead. DSR must be active (step 008 of MOl with the + meter lead. 898 running).

Does RI (RING INDICATE) pulse with each IS OFF HOOK at a + EIA level (+3 to +25 ring? VDC)? V N Y N

053 058 Coupler problem. Bad C2 (38LS) card. Have the customer notify the responsible See the BSC MIM for jumpering and person. switch setting instructions.

054 059 - Make DTR active by pressing ATTN key once to Cable problem. display the option menu, then run step 8. See logic diagram 455. Check the SG - Probe the OH (Blue) terminal at the coupler with (SIGNAL GROUND) wire also. the + meter lead. 060 Is OH (OFF HOOK) at a + EIA level (+3 to Did ringing stop when DTR was made active? +25VDC)? Y N Y N 061 055 Coupler problem. - Probe C2G13 (RING INDICATE) with the + Have the customer notify the responsible meter lead. Connect the - meter lead to a person. 008 (logic ground) pin. 062 Is RING INDICATE at a + EIA level (+3 to (Entry Point D) +25 VDC) when the telephone rings? Y N - If a N is on the decision line of the MOl display, restart step 008 and redial the modem 056 telephone. Cable problem. - Probe the DA (Yellow) terminal at the coupler See logic diagram 455. Check the SG with the + meter lead. (SIGNAL GROUND) wire also. , ,>, Is DA (DATA MODEM READY) at a + EIA level (+3 to +25 VDC)? Y N

01JAN79

EC 836600 PEC 835541 7 7 N P Q R MAP 0832-6 Local CBS coupler MAP L S MAP 0832-7 5 for 38LS

PAGE 7 OF 7

063 070 - Probe C2J02 (DATA MODEM READY) with - Check for continuity of the DT and DR signal the + meter lead. wires. See logic diagram 445. (This can also .. C'" be done by checking for a signal with the db Is DATA MODEM READY at a + EIA level meter at the DT and DR terminals at the (+3 to +25 VDC)? coupler.) Y N Does the cable test OK? 064 Y N Bad C2 (38LS) card. See the BSC M I M for jumpering and 071 switch setting instructions. Bad cable.

065 072 Cable problem. Bad coupler. See logic diagram 455. Have the customer notify the responsible person. 066 - Probe the CCT (Brown) terminal at the coupler 073 with the + meter lead. Go to Page 6, Step 062, Entry Point D.

Is COUPLER CUT THROUGH at a + EIA level c (+3 to +25 VDC)? Y N

067 Coupler problem. Have the customer notify the responsible person.

068 - Probe C2J09 (COUPLER CUT THROUGH) with the + meter lead.

Is CCT at a + EIA level (+3 to +25 VDC)? Y N

069 Cable problem. See logic diagram 455.

c' 01JAN79 EC 836600 PEC 835541 S MAP 0832-7 This page intentionally left blank.

MAP 0832-8 Manual Call to a Manual Answer A MAP 0833-1 Station using a COT Type Coupler

PAGE 1 OF 2

001 007 Use this MAP to isolate connection problems (Entry Point A) when the local station has a COT (no auto answer function) type coupler by using a nearby - Load MOl 890 from the communications telephone. diagnostic cartridge or the 5110 diagnostic diskette. E'nter 898 to select the BSC test - Be sure the Test switch (if provided) on the patterns. DO NOT enter 0 to select the option COT type coupler is in the normal operating menu at this time. Select step 008 to transmit position. continuous SYN characters. ( - Lift the modem handset from cradle. - Lift the Exclusion key. This puts modem telephone in data mode. Do you hear the dial tone 7 - DO NOT cradle the handset. Y N Does the nearby telephone hear the 002 continuous SYN characters? Exclusion key problem in the modem Y N telephone. Have the customer notify the responsible 008 person. - Use the ear plug with the CE meter and DB adapter to listen to the continuous SYN 003 characters (connect meter leads DT (DATA - Cradle the modem telephone handset, then TIP) and DR (DATA RING) terminals at the have someone call the local modem telephone coupler). from a nearby telephone. Do you hear the SYN characters? Does the modem telephone ring? Y N Y N 009 004 Is a N displayed on the reply line of the Telephone problem. MOl display? Have the customer notify the responsible Y N person. 010 005 Modem problem. - Lift the handset on the modem telephone. If using an OEM modem, have the Can you talk with the person on the nearby customer notify the responsible person. telephone? Y N If using an IBM external modem, use the maintenance information provided with 006 that modem. Telephone problem. c Have the customer notify the responsible 011 person. The routine to transmit the continuous SYN characters is not running. Go to Step 007, Entry Point A.

© Copyright IBM Corp. 1979 01JAN79

EC 836600 PEC 835541 2 2 A B C MAP 0833-1 B C Manual Call to a MAP 0833-2 1 1 Manual Answer Station

PAGE 20F 2

012 Coupler problem. Have the customer notify the responsible person.

013 Test completed satisfactory. Cradle both telephone handsets.

01JAN79

EC 836600 PEC 835541

MAP 0833-2 DIGITAL NETWORK REMOTE A MAP 0834-1 ( WRAP TEST PROCEDURE PAGE 1 OF 1

001 005 Use this MAP to test the digital network with a - Remove the DOL jumper from the ODSA card remote DDSA station. at the local station and run BSC34 of MOl 896. - Have the remote station run the remote test. - Before using this MAP, MOl 821 must run without errors. The remote stations' Test run OK? diagnostics must run without errors also. V N - If the Disable Double Loopback (DOL) jumper is installed on the remote DDSA communication 006 facility card, have the remote service person Verify that the local and remote stations are remove it (see BSC MIM for the location of the set up correctly to run the test. If the set up is jumper). correct, the problem is in the digital telephone - NOTE- For normal operation DOL must be network. jumpered on all tributary stations on a Have the customer notify the responsible multipoint network. Otherwise wrap tests run person. by any tributary station will seriously degrade the operation of the rest of network. 007 - Have the remote station loop a local wrap test. The local and remote BSCA and the digital - Load MOl 890 from the communications network tested OK. diagnostic cartridge or the 5110 diagnostic Replace the DOL jumper if it was removed. diskette. - Select BSCA MOl 896. - Run BSC35 of MOl 896 while the remote station is in local wrap mode. The test will be wrapped back to the local DDSA. from the remote DDSA communication facility.

Test run OK? (no errors displayed by MOl 896) V N

002 Verify that the local and remote stations are set up correctly to run the test. If they are set up correctly, the problem is in the digital telephone network. Have the customer notify the responsible person.

003 Does the remote station have a remote wrap test? V N

004 Test complete. c © Copyright IBM Corp. 1979 01JAN79 EC 836600 PEC 835541 A MAP 0834-1 This page intentionally left blank.

\1'{,'. )1

MAP 0834·2 BSC Network and BSCA A MAP 0835-1 Intermittent Problem MAP

PAGE 1 OF 5

001 005 Use this MAP as a guide to resolve BSC network - If the local station is on a nonswitched problems and BSCA intermittent problems. telephone network and has the Switched Network Backup (SNBU) feature on the - Have the customer maintain a record of the modem, switch to SNBU. symptoms and error codes. See the BSC M I M for a description of the error codes. Is the local station operating on a switched - Have the customer maintain a record of the network or SNBU? error log and error history. See the BSC Users Y N Guide to print the error log and error history. - Verify that the configuration record{s) is correct. 006 See the BSC Users Guide to display the This section of the MAP is for a nonswitched configuration record{s). (leased) telephone network. - Verify that the features, modems and strapping options (echo clamp, clear to send delay, Is the local station using an external transmit speed) are compatable with the remote modem? station{s). Y N - Run the 5110 System Test to verify that another problem on the 5110 is not causing the 007 BSC problem. - Use logic diagram 455 to check continuity of the external cable. Does the 5110 System Test run OK? V N Does the external cable test OK? V N 002 Correct any problem indicated by the System 008 Test. Repair or replace the external cable.

003 009 - Loop MOl 821 for 10 minutes by setting up a (Entry Point F) path starting with step 005. The path stop number depends upon which communication - Use MAP 0831 to check the transmit and facility card is installed. See the 5110 MIM for receive levels. details to set up a path. Are the transmit and receive levels Does MOl 821 loop without any errors? correct? V N V N

004 010 Correct any problems indicated by MOl 821. Use MAP 0831 to fix the problem.

C: © Copyright IBM Corp. 1979 01JAN79 EC 836600 PEC 835541 332 A BCD MAP 0835-1 D SSC Network and SSCA E F G MAP 0835-2 1 Intermittent Problem MAP PAGE 2 OF 5

011 017 The local station tests OK on a switched Are the BSC On Line/RFT tests available on telephone network. Suspect the this nonswitched network? nonswitched telephone network, the V N remote station, customers' program or procedure. 012 (Entry Point E) 018 Suspect the telephone network or the - Use the accoustic coupler feature of a 1200 customers program or procedure. TDAT or TRAP to communicate with a remote station that has BSC On Line/RFT 019 test capability. See the BSCA MIM for 1200 - Prepare the 5110 to run the BSC/RFT On Line TDAT and TRAP procedures. NOTE- Before test. See the BSC M I M for instructions. using the TRAP on a 38LS integrated modem, ask the local BODS for assistance. Does the On Line test run OK? V N Does the test run OK? V N 020

013 Is the local station on a multipoint - Try testing with another remote station. network? V N Does this test run OK? V N 021 Go to Step 012, Entry Point E. 014 - Use the TRAP to record a failure. See 022 the BSCA M I M for the TRAP Is this the only station on the multipoint procedure. NOTE- Before using the network that fails? TRAP on a 38LS integrated modem, V N ask the local BODS for assistance. 023 Does the TRAP printout indicate the Have the host (primary) station localize the problem? problem. V N 024 'II.; ..,,' 015 Go to Step 012, Entry Point E. Ask your manager for assistance. 025 016 Suspect the customers' program or procedure. Correct the problem.

01JAN79 l .. l EC 836600 PEC 835541 E F G MAP 0835-2 B C BSC Network and BSCA H J K MAP 0835-3 1 1 Intermittent Problem MAP

PAGE 3 OF 5

026 035 Is it an IBM external modem? - Use MAP 836,837 and 838 to test the Y N World Trade II~e plate.

027 Does the line plate test OK? Go to Page 1, Step 009, Entry Point F. V N

028 036 - Use the modem maintenance information to Use MAP 836,837 and 838 to fix the run the modem diagnostic tests. problem.

Do the modem tests run OK? 037 Y N Go to Step 043, Entry Point B.

029 038 Repair the modem using the maintenance - Use MAP 0833 to test the COT type coupler. information provided with the modem. Does the COT type coupler test OK? 030 Y N Go to Page 1, Step 009, Entry Point F. 039 "·., 031 Use MAP 0833 to fix the problem. C (Entry Point C) 040 - Use MAP 0831 to check the transmit and Go to Step 043, Entry Point B. receive levels. Are the transmit and receive levels OK? 041 Y N - Use MAP 0832 to test the CBS type coupler.

032 Does the CBS type coupler test OK? Use MAP 0831 to fix the problem. Y N

033 042 Use MAP 0832 to correct the problem. Is the 10~1 station using a CBS (Auto ( " Answer) type coupler? 043 /' Y N (Entry Point B)

034 - Prepare the 5110 to run the SSC On Line/RFT Is the local station using a COT type tests. See the SSC MIM for instructions. coupler? Y N Does the BSC On Line/RFT test run OK? Y N c 01JAN79 EC 836600 PEC 835541 5 4 H J K L M MAP 0835-3 M BSC Network and BSCA N P Q R MAP 0835-4 3 Intermittent Problem MAP

PAGE 4 OF 5

044 051 - Dial another remote station and run the test - Verify that the TDAT or TRAP again. procedure is correct. If the procedure is correct, try testing with another Did the test run OK? remote station. Y N Does the On Line/RFT test run OK? 045 Y N Is the local station using a 38LS integrated modem? 052 Y N - Use the TRAP to record a failure.

046 Does the TRAP printout indicate Is it an IBM external modem? the problem? Y N Y N

047 053 Go to Step 050, Ask your manager for assistance. Entry Point G. 054 048 Correct the problem. - Use the maintenance information for the modem to run a test on the modem. 055 Suspect the first remote station or that Does the modem test run OK? redialing corrected the problem. Y N 056 049 OEM modem or telephone network Use the maintenance information problem. provided with the modem to repair the Have the customer notify the responsible modem. person.

050 057 (Entry Point G) Ask the local BODS for assistance.

- Use the 1200 TDAT or TRAP procedure 058 to bypass the modem. See the BSC MIM Suspect the first remote station or that redialing for the 1200 TDAT or TRAP procedure. corrected the problem. - Prepare the 5110 to run the BSC On Line / RFT test.

Does the the On Line test run OK with the modem bypassed? Y N

01JAN79

EC 836600 PEC 835541 N P Q R MAP 0835-4 BSC Network and BSCA MAP 0835-5 Intermittent Problem MAP PAGE 5 OF 5

059 The local station tests OK. Suspect the telephone network, remote station or customer procedure. For intermittent problems, consider vibrating the 5110 to detect loose connections, check the AC and DC voltages, heat and cool the 5110 to aggravate the problem. Use the error history listings that the customer printed to help isolate the cause of the problem. See appendix E in the SSC Users Manual for the meaning and possible cause of the error codes in the sse history table. For more information, see the 5110 M 1M.

( '" /

"'~

(/ c c 01JAN79 EC 836600 PEC 835541 MAP 0835-5 This page intentionally left blank.

/' '

MAP 0835-6 Automatic Answer MAP for 38LS MAP 0836-1 with World Trade Line Box

PAGE 1 OF 5

001 - Be sure that MOl 821 runs OK before using this MAP. - Remove the 5110 top cover. - Press RESTART on the 5110.

Is there a telephone set associated with the data station? (' Y N 002 (Entry Point A) The jumper allows the 5110 to go to data mode - Connect a jumper from C2B02 (-Data after three good ring trains are detected. Terminal Ready) to C2008. - Dial the data station from a nearby telephone set.

Is the busy tone present? V N

003 - Ringback tone can be heard in the nearby handset. Data station answers after the third ring pulse train.

Is the 3.5s answering tone (2100 Hz) present? V N

004 - Measure the DC voltage between C2J02 is connected to a Transfer Relay point in C2J02 and C2J08. the line box. When the 5110 is in data mode, C2J02 is -3.5VoC; otherwise, C2J02 is open. Is C2J02 at -3.5VDC after three ring pulse trains? Y N

© Copyright IBM Corp. 1979 01JAN79 EC 836600 PEC -----.. - 5 4 3 3 2 ABC 0 E MAP 0836-1 E Automatic Answer MAP MAP 0836-2 1 World Trade 38lS PAGE 2 OF 5

005 - Ensure that C2B02 is jumpered to C2D08. C2G 10 and C2G 13 signal levels: - Redial the data station from a nearby telephone Without ring current set. Off: about 1V ac. - Check with a voltmeter (5V ac), C2G 10 (Current Detection 1) and C2G13 (Current Detection 2). With ring current On: voltage increases by 0.3V to 1V ac.

Current Detection 1 signal level can be different /' '-, from Current Detection 2. ~. ,: Are both signals pulsing with the ring signal? V N

006 - Measure ac voltage at the telephone line. DC current up to 48V is present. The voltmeter DANGER must indicate a signal oscillating between 48V Signal measured can be higher than 150V ac. and 78V, and a gap of about 30V ac between silent and ring periods. Do not ground one of the telephone wires.

Are there ac pulses (ringing current) higher than 30V ac? V N

007 Ask the customer to call the PTT representative.

008 (Entry Point B) Possibility of a short circuit in the connection. Check with an ohmmeter the telephone cable(s) from the line box to the wall-mounted connector. See logic diagram 470.

Is the cable(s) OK? V N I 009 Bad telephone cable(s).

010 Bad line box assembly P / N 4836775

01JAN79

EC 836600 PEC ------­ 3 F MAP 0836-2 C D F Automatic Answer MAP MAP 0836-3 1 1 2 ( World Trade 38LS PAGE 3 OF 5

011 Probe C2G03 (Transfer Relay). C2G03 signal levels: On: -2.7V (~' Off: -4.5V Is the signal on? Y N

012 Bad C2 (38LS) card. The 38LS should raise Transfer Relay when Current Detection 1 and Current Detection 2 rise (together three times), and when the 5110 is in data mode.

013 Bad line box assembly P / N 4836775

014 - Check for the presence of the 2100 Hz Use an intercom or a dbmeter. between C2D08 and C2D05.

Is 2100 Hz present during 3.5 seconds? Y N

015 Bad C2 (38LS) card. The 38LS should send a 2100 Hz tone during 3.5s, when answering a call automatically.

016 Bad line box assembly P / N 4836775

017 Does the answering tone stop after 3.5 seconds? Y N

018 Bad C2 (38LS) card.

019 Auto-answer function is OK. Check other c' functions as appropriate. Remove the jumper from C2B02 to C2D08.

01JAN79 c EC 836600 PEC ------­ MAP 0836-3

f B Automatic Answer MAP MAP 0836-4 1 World Trade 38LS

PAGE 4 OF 5

020 - Power off the 5110. - Keep the jumper on C2B02 to C2D08. - Redial the data station.

Is the busy tone present? V N

021 - Power on the 5110. C2G03 signal levels: 'I, / - Probe C2G03 (Transfer Relay). On: -2.7V Off: -4.5V

Is the signal on? V N

022 Bad line box assembly P / N 4836775

023 - Probe C2G 10 (Current Detection 1) and C2G 10 and C2G 13 signal levels: C2G 13 (Current Detection 2). On: -3V Off: +1V Are both signals off? V N

024 Bad line box assembly P / N 4836775

025 - Oisconnect the 5110 from the telephone line C2G03 signal levels: (at the wall-mounted connector level). On: -2.7V - Remove the jumper from C2B02 to C2D08. Off: -4.5V - Press RESTART on the 5110. - Probe C2G03 (Transfer Relay).

Is the sign~1 on? V N

026 Bad line box assembly P / N 4836775

027 Bad C2 (38LS) card.

01JAN79

EC 836600 PEC ------­ 5 G MAP 0836-4 A G Automatic Answer MAP MAP 0836-5 1 4 World Trade 38LS

PAGE 5 OF 5

028 - Disconnect the 5110 from the telephone line Ringback tone should be present. (at the wall-mounted connector level). - Retry the call.

Is the busy tone present? V N

029 Go to Page 2, Step 008, Entry Point B.

030 Ask the customer to call the PTT representative.

031 - Use MAP 838 to check the manual answer operation, then return to this point.

Is the manual answer operation OK? V N

032 (: Use MAP 838 to repair. 033 Go to Page 1, Step 002, Entry Point A.

c

01JAN79 C: EC 836600 PEC ------­ MAP 0836-5

, , , "'r",,~~. ___~' ",."tm:- .,~ ______..... ~ ...... _~~.~ ... "u~_'_ •• ~~_~._._ .. __ .• _'._. ___. ___,_._. __. __ .~ ____----1..-_ ... _- 'I, .,1

This page intentionally left blank.

MAP 0836-6

1 Manual Call MAP for 38LS with MAP 0837-1 World Trade Line Box

PAGE 1 OF 4

001 - Be sure MOl 821 runs OK before using this MAP. - Remove 5110 top cover. - Press RESTART on the 5110. - Lift the handset of the associated telephone set.

Is the dial tone present? " ( "" .. Y N 002 - Power off the 5110; retry the call.

Is the dial tone present? Y N

003 Is the 5110 connected to the telephone line with a jack? Y N

'II' 004 ( - Disconnect the 5110 from the Dial tone present, called telephone rings and ./' telephone line and connect the communication is established. telephone set directly to the line (at the wall- mounted connector level).

(Entry Point A) - Dial a nearby telephone set.

Is the conversation OK? Y N

005 Ask the customer to call the PIT c representative.

© Copyright IBM Corp. 1979 01JAN79 EC 836600 PEC ------­ 2 222 ABC 0 MAP 0837-1 Manual Call MAP for MAP 0837-2 World Trade 38LS PAGE 2 OF 4

006 (Entry Point B) Possibility of a short circuit in the connection. - Check with an ohmmeter the telephone cable(s) from the line box to the wall-mounted connector. See logic diagram 470.

Is the cable(s) OK? Y N

007 Bad cable(s).

008 Bad line box assembly P / N 4836775

009 - Unplug the jack. Go to Page 1, Step 004, Entry Point A.

010 - Power on the 5110. C2G03 signal levels: - Probe C2G03 (Transfer Relay). On: -2.7V Off: -4.5V Is the signal on? Y N

011 Bad line box assembly P / N 4836775

012 Bad C2 (38LS) card.

013 - Dial a nearby telephone set. Dial tone present, called telephone rings and communication is established.

Is the conversation OK? Y N

014 Ask the customer to call the the PTT representative.

01JAN79

EC 836600 PEC ------­ 3 E MAP 0837-2 E Manual Call MAP for MAP 0837-3 2 World Trade 38LS

PAGE 3 OF 4

015 - Keep the handset off hook. No more tone; silent handset. - Connect a jumper from C2B02 (-Data Terminal (' Ready) to C2D08.

Is the associated telephone set disconnected from the line? Y N

016 - Probe C2G10 (Current Detection 1) and C2G 10 and C2G 13 signal levels: C2G 13 (Current Detection 2). On: -3V Off: +1V Is one of these signals on 1 Y N

017 Go to Page 2, Step 006, Entry Point B.

018 - Probe C2G03 (Transfer Relay). C2G03 signal levels: On: -2.7V Off: -4.5V c Is the signal on? Y N

019 Bad C2 (38LS) card. Transfer Relay should be on when the 5110 is in data mode and the handset lifted.

020 Bad line box assembly P / N 4836775 Remove the jumper from C2B02 to C2D08. '" 021 - Remove the jumper from C2B02 to C2D08. ~ .. _"y C - Press RESTART on the 5110.

Is the conversation with the nearby telephone set OK again? c Y N

01JAN79 c EC 836600 PEC ------­ 4 4 F G MAP 0837-3 F G Manual Call MAP for MAP 0837-4 3 3 World Trade 38LS

PAGE 4 OF 4

022 Bad line box assembly P/ N 4836775 Busy tone in the nearby handset, and/or dial tone in the associated handset.

023 The local telephone line is OK. - Ask the customer to make a data transmission to a remote data station.

'I. }' Is the data transmission OK? V N

024 Loop MOl 821 in path mode to test the BSCA again. See the 5110 MIM for details to set up a path. If MOl 821 runs OK, suspect the line box assembly.

025 Manual call function is OK. Check other functions as appropriate.

'''I,

01JAN79

EC 836600 PEC ------­

MAP 0837-4 Manual Answer MAP for 38LS MAP 0838-1 ( with World Trade Line Box PAGE 1 OF 5

001 - Be sure MDI 821 runs OK before using this MAP. - Remove the 5110 top cover. - Press RESTART on the 5110. - Dial the data station from a nearby telephone set.

Is the busy tone present? Y N

002 Wait for at least 3 rings. Is the associated telephone set ringing? Y N

003 In the nearby handset: modem answering tone or data can be heard. Is the modem connected to the line? Y N

004 - Lift the handset of the associated telephone set.

Is the dial tone present? Y N

005 Go to Page 5, Step 030, Entry Point B.

006 Ask the customer to call the PTT c representative. 007 - Probe C2G03 (Transfer Relay). C2G03 signal levels: On: -2.7V Off: -4.5V Is the signal on? V N

008 Bad line box assembly P / N 4836775 c © Copyright IBM Corp. 1979 01JAN79 EC 836600 PEC ------322 ABC MAP 0838-1

______.... L .. .. _._____ ._ .... _. ___ .. _. ______.______B C Manual Answer MAP for MAP 0838-2 1 1 World Trade 38LS

PAGE 2 OF 5

009 Bad C2 (38lS) card. Transfer Relay should be off when the 5110 is not in data mode.

010 - Answer the call.

Is the conversation OK? V N

011 Ask the customer to call the PTT representative.

012 - Keep the handset off hook. No more tone; silent handset. - Connect a jumper from C2B02 (-Data Terminal Ready) to C2D08.

Is the associated telephone set disconnected from the line? V N

013 - Probe C2G 10 (Current Detection 1) and C2G 10 and C2G 13 signal levels: C2G13 (Current Detection 2). On: -3V Off: +1V Is one of these signals on? V N

014 Go to Page 5, Step 030, Entry Point B.

015 - Probe C2G03 (Transfer Relay). C2G03 signal levels: On: -2.7V Off: -4.5V

Is the signal on? V N

016 Bad C2 (38lS) card. Transfer Relay should be on when the 5110 is in data mode and the handset lifted.

01JAN79

EC 836600 PEC ------­ 3 3 o E MAP 0838-2 Manual Answer MAP for MAP 0838-3 World Trade 38LS ( PAGE 3 OF 5

017 Bad line box assembly PIN 4836775 Remove the jumper from C2B02 to C2D08.

018 - Remove the jumper from C2B02 to C2008. - Press RESTART on the 5110.

Is the conversation with the nearby telephone set OK again? V N

019 Bad line box assembly PIN 4836775 Busy tone in the nearby handset, and I or dial tone in the associated handset.

020 The local telephone line is OK. - Ask the customer to prepare the 5110 for a data transmission. - Ask the remote station to dial the local da~a station. c: - Answer the call manually. - Make a data transmission.

Is the data transmission OK? V N

021 loop MOl 821 in path mode to test the BSCA again. See the 5110 MIM for details to set up a path. If MOl 821 runs OK, suspect the line box assembly.

022 The manual answer function is OK. Check other functions as appropriate.

023 - Power off the 5110; retry the call.

Is the busy tone still present? C: Y N

01JAN79 EC 836600 PEC -----.. - c 4 4 F G MAP 0838-3

___.,..1,. _____,. ______•______------F G Manual Answer MAP for MAP 0838-4 3 3 World Trade 38LS PAGE 4 OF 5

024 - Power on the 5110. C2G03 signal levels: - Probe C2G03 (Transfer Relay). On: -2.7V Off: -4.5V

Is the signal on? V N

025 Bad line box assembly PIN 4836775

026 Bad C2 (38lS) card. Transfer Relay should be off when the 5110 is not in data mode.

027 Is the data station connected to the telephone line with a jack? V N

028 - Disconnect the data station from the No busy tone, called telephone set rings, telephone line and connect the associated communication is established. telephone set directly to the telephone line (at the wall-mounted connector level).

(Entry Point A) - Dial the data station from a nearby telephone set. Is the conversation OK? V N

029 Ask the customer to call the PIT representative.

01JAN79

EC 836600 PEC ------­ 5 5 H J MAP 0838-4 H J Manual Answer MAP for MAP 0838-5 4 4 World Trade 38LS PAGE 5 OF 5

030 (Entry Point B) Possibility of a short circuit in the connection. "'" ( - Check with an ohmmeter the telephone J cable(s) from the line box to the wall-mounted connector. See logic diagram 470.

Is the cable(s) OK? Y N

031 Bad cable(s).

032 Bad line box assembly P / N 4836775

033 - Unplug the jack. Go to Page 4, Step 028, Entry Point A.

c

c 01JAN79 EC 836600 PEC ------­ MAP 0838-5 This page intentionally left blank.

MAP 0838·6 AUXILIARY TAPE MAP MAP 0850-1

PAGE 1 OF 2

ENTRY POINTS EXIT POINTS FROM ENTER THIS MAP EXIT THIS MAP TO MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT

0200 A 001 2 009 0420 A ( '''' ~, 0861 A 001 2 008 0420 A

001 (Entry Point A)

This is the entry MAP for the 5106.

Information on the use of the CE probe can be found in Appendix B of the 5110 MIM. If the PROCESS CHECK light is on, the 5106 M DI cannot be loaded.

Is the PROCESS CHECK light on" c Y N 002 Use the keys on the numeric section of the keyboard:

-Press HOLD -Hold CMD and press -(minus) - For BASIC, hold CM D and press * (multiply) -For APL, hold CMD and press x (multiply) -Press C -Press 1 - Press EXECUTE

Did the PROCESS CHECK light come on? Y N

003 Do the words TAPE READ DIAGNOSTIC appear on the top line of the display? c Y N I c © Copyright IBM Corp. 1979 01JAN79 EC 836600 PEe 835541 2 222 ABC D MAP 0850-1 ABC 0 AUXILIARY TAPE MAP MAP 0850-2 1 1 1 1

PAGE 2 OF 2

004 Bad F2 (Common and language ROS) card.

005 Follow the instructions on the display lmtil DSP MENU appears. Then:

-Enter 840

- Press EXECUTE .~.

The 5106 MOl should now load and run. If the PROCESS CHECK light comes on GO TO MAP 0420, ENTRY POINT A.

Follow the instructions on the display. When completed, return to this step.

-Press RESTART -Do the test for the 5106 near the end of the Select Magnet Service Check (see MIM 221).

Is the tape motion rhythmic? V N

006 Do the Tape Select Magnet Servie Check (see MIM 221).

007 The 5106 tape select magnets are operating properly

008 Go To Map 0420, Entry Point A.

009 Go To Map 0420, Entry Point A.

01JAN79 "t EC 836600 PEC 835541

MAP 0850-2 5114 MAP 0880-1 ( 5114 MAP PAGE 1 OF 3

ENTRY POINTS EXIT POINTS FROM ENTER THIS MAP EXIT THIS MAP TO MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT

0200 A 001 3 015 420 A 3 019 420 A

001 (Entry Point A)

This is the entry map for 5114. If a PROCESS CHECK occurs while using the MOl, reload the MOL If the PROCESS CHECK persists, go to MAP 420, entry point A.

Before using the MOl, make sure the diskette is not damaged, and the problem occurs on more than one diskette.

After any adjustment or part replacement, the machine must be tested. If the problem has not been corrected, reseat the cards and cables. Load the diagnostic again.

Check for the following possible defects;

Foreign material in the diskette or diskette drive Belt off or damaged Broken cover/pivots or missing or loose screws Motor or pulleys not turning Loose pulleys Accessing band broken or damaged Loose guide rods Loose cables or cards Fan not turning (see 5114 MIM 182).

Is the PROCESS CHECK light on 7 Y N

© Copyright IBM Corp. 1979 01JAN79 ..-= EC 836600 PEC 835541 1- 3 2 A B MAP 0880-1 B 5114 E F MAP 0880-2 1 5114 MAP

PAGE 2 OF 3

002 005 Is the diskette difficult to insert or remove Follow the instructions on the display. from the drive? NOTE: If the 5103 is the terminating device, V N the 5103 I/O interface cables and the i" 5103 adapter card can also cause 003 problems in the 5114. - Disconnect all of the I/O devices from the 5110 I/O interface port. 006 - Connect the failing 5114 to the 5110. Are there two diskette drives in the 51141 -Connect the cable terminator to the 5114. V N NOTE: If a cable terminator is not available, use the 5103 as the terminating device. 007 (Entry Point C) -Press RESTART. Wait 25 seconds. Use the keys on the numeric keyboard: Did you disconnect a 51 06 and/or a second -Press HOLD 5114? -Hold CMD and press -(minus) V N -For BASIC, hold CMD and press *(multiply) -For APL, hold CMD and press X(multiply) 008 -Press C Suspect the 5103 if attached when the -Press 1 failure occured. The parts in the 5103 to - Press EXECUTE suspect are the printer I/O cable and the printer adapter card. Follow the instructions on the display until the DSP MENU appears and then; 009 -Connect the 5106 and/or the second 5114 to -Enter 881 the I/O interface port one at a time, in the - Press EXECUTE same position they were before you disconnected them. The 5114 MOl should now load and run. - Press RESTART. Wait 25 seconds. -Rerun MDI 881 on the same drive. Is the PROCESS CHECK light on? V N DO NOT FOLLOW THE INSTRUCTIONS ON THE DISPLAY IF AN ERROR CONDITION 004 OCCURS. - Follow the instructions on the display. Did the MOl run to completion? Did the MOl run to completion·' V N V N

,/

01JAN79

EC 836600 PEC 835541 3 3 333 C D E F G H J MAP 0880-2 o G H J 5114 A C MAP 0880-3 222 2 1 2 5114 MAP PAGE 3 OF 3

010 016 The trouble is in the 5106 or the second Are the heads loaded all the time? :~ '.".'.! 5114. Suspect the I/O interface cables V N ( ) in either the 5106 or the second 5114 (see MAP 0210 and MIM 280) and the 017 cables 01 and 03 in the second 5114 or Check the head load bail return spring and the cables B1 and B2 in the 5106, or the bail stop screw (see 5114 MIM 130). adaptor cards in the 5106 and the Preform the head load service check (see second 5114. Go to MAP 0850 for the 5114 MIM 130). 5106 or rerun MOl 881 for the second Bad drive control card. 5114. Bad 5114 C 1 (adapter) card (see MAP 050 before replacing this card). 011 No trouble found. 018 Suspect the 5103 if attached when the Bad drive control card. failure occured. The parts to suspect in Check for shorts on the Taper Pin Block (see the 5103 are the 5103 I/O interface cable 5114 MIM 130). and the 5103 adaptor card. 019 012 Go To Map 420, Entry Point A. Run the MOl on the other diskette drive:

- Press A TIN twice The OSP MENU should appear. -Enter 881 -Press EXECUTE

Did the MOl run to completion? V N

013 Follow the instructions on the display. NOTE: If the 5103 is the terminating device, the 5103 I/O interface cables and the 5103 adapter card can also c; cause problems in the 5114. 014 Go to Page 2, Step 007, Entry Point C.

015 c Go To Map 420, Entry Point A.

01JAN79 ••-= EC 836600 PEC 835541 1- MAP 0880-3 This page intentionally left blank.

MAP 0880-4 MACHINE CHECKOUT MAP MAP 0900-1

(" '\ PAGE 1 OF 13

ENTRY POINTS EXIT POINTS ( -'-', FROM ENTER THIS MAP EXIT THIS MAP TO MAP ENTRY PAGE STEP PAGE STEP MAP ENTRY NUMBER POINT NUMBER NUMBER NUMBER NUMBER NUMBER POINT

0200 A 1 001 2 004 0200 A 0200 C 3 016 10 102 0300 A (~/ 0200' 0 8 079 12 119 0300 A 0200 F 6 050 10 101 0310 A 0300 A 1 001 2 012 0400 A 0310 A 1 001 2 006 0420 A 0845 A 1 001 5 045 0420 A 3 019 0420 A 7 072 0420 A 9 088 0420 A 9 092 0420 A 13 127 0420 A 10 103 0420 A 12 123 0420 A 2 005 0500 A (~'\ 5 049 0500 A 6 057 0500 A 5 048 0500 A 3 018 0600 A 3 028 0600 A 4 030 0600 A 4 032 0600 A 9 087 0600 A

001 (Entry Point A) ('." -If there is an internal tape drive or a 5106, make ,/ sure that the tape cartridges are removed. - Power down. -Power up. Wait 25 seconds. -Set the BRIGHTNESS control so that the characters are well defined. -Switch the L32-64-R32 switch to 64. C -Press the bottom of the REVERSE DISPLAY switch. -Switch the DISPLAY REGISTERS switch to NORMAL. (Step 001 continues) C\ © Copyright IBM Corp. 1979 01JAN79 EC 836600 PEC 835541 MAP 0900-1 I MACHINE CHECKOUT D MAP 0900-2

PAGE 2 OF 13

(Step 001 continued) 010 Did either LOADO or CLEAR WS (spelled Is the IN PROCESS light on? correctly) appear only once on one and only V N one line of the 5110 display? V N 011 Are the top 13 lines of the display entirely 002 blank (there are 16 lines total for the Is the PROCESS CHECK light on? display)? V N V N

003 012 Is the 5110 display dark for all positions Go To Map 0400, Entry Point A. of the BRIGHTNESS control? V N 013 -Press and hold the RESTART switch. 004 Go To Map 0200, Entry Point A. Are both the PROCESS CHECK and IN PROCESS lights on? 005 V N Go To Map 0500, Entry Point A. 014 006 Bad L2 (exec ROS) card (see MAP 050 for Go To Map 0420, Entry Point A. jumpering). Bad PROCESS CHECK light. 007 Bad IN PROCESS light. The 5110 display raster is grossly distorted if it Bad RESTART switch. has a black rather than a white background, or is Check/ replace Z3 (display and control greatly reduced in size. panel) cable (see MAP 0210 and MIM 248,249). Is the 5110 display raster grossly distorted? VN 015 -Release the RESTART switch. Wait 25 008 seconds. Is the 5110 display raster rolling? V N Is the PROCESS CH ECK light on? V N 009 Does the 5110 display raster contain wide horizontal bars similar to a TV set with the horizontal hold out of adjustment? V N

01JAN79 '{. EC 836600 PEC 835541 555 553 ABC 0 E F G MAP 0900-2 G MACHINE CHECKOUT H J K L MAP 0900-3 2

PAGE 3 OF 13

016 023 (Entry Point C) Bad H2 (base I/O) card.

-Press each key (except the HOLD, CMD, ATTN, 024 EXECUTE keys and the space bar. Do not try Bad SPACE key module. the repeat function). Bad keyboard PC board (see MIM 251). -Observe the display for proper characters or Check/ replace Z4 (keyboard) cable (see functions (see M I M 250 and keyboard theory Map 0210 and MIM 206,255). section 3). 025 Do the keys function correctly? Bad key module Y N (See MIM 253). Bad keyboard PC board (see MIM 251). 017 Check/ replace Z4 (keyboard) cable (see Map Is the PROCESS CHECK light on? 0210 and MIM 206,255). Y N Bad G2 (display) card (see MAP 050 for jumpering). 018 Go To Map 0600, Entry Point A. 026 -Press and hold the P key. 019 Go To Map 0420, Entry Point A. Does the P key perform the repeat function? (The answer is N if the machine is operating 020 correctly). - Press and hold the SPACE bar. Y N

Does the repeat function work correctly? 027 Y N -Release the P key. - Press the backspace key until a character 021 flashes. - Press and hold the SPACE bar. - Press A TIN. -Probe H2-B04 (+typamatic). (See appendix B, the general logic probe, in Did the character at the cursor location the 5110 MIM). and the remaining characters after the cursor disappear? Is the UP light on? Y N c Y N 028 022 Bad A TIN key. - Remove the keyboard cable at Z4. -Probe H2-B04 (+typamatic). Go To Map 0600, Entry Point A.

Is the DOWN light on? Y N c" 01JAN79 EC 836600 PEC 835541 5 4 H J K L M N MAP 0900-3 I N MACHINE CHECKOUT P Q MAP 0900-4 3

PAGE 4 OF 13

029 034 - Press the P key twice. -Release the shift key. -Press EXECUTE. - Press the $ key several times. -Press the HOLD key. The word VALUE ERROR or ERROR 500 should - Hold the shift key down and press the 8 key appear on the display with other characters. on the numeric keyboard.

Are the words VALUE ERROR or ERROR 500 Did the $ characters change to ¥ (yen)? on the display? Y N Y N 035 030 Bad G2 (display) card (see MAP 050 for Bad EXECUTE key. jumpering). Bad H2 (base I/O) card. Go To Map 0600, Entry Point A. Bad keyboard PC board (see MIM 251). Check/ replace Z4 (keyboard) cable (see 031 Map 0210 and MIM 206,255). -Press HOLD. 036 The cursor / character should stop flashing or -Press the HOLD key. disappear. - Hold the shift key down and press the (period) key on the numeric keyboard. Did the flashing stop or disappear? Y N Go to Page 6, Step 050, Entry Point F.

032 037 Bad HOLD key. - Release the shift key and press the $ key several times. Go To Map 0600, Entry Point A. -Press the HOLD key. - Hold the shift key down and press the 0 key on 033 the numeric keyboard. Now check out the ability of the machine to do a character set selection. Did the $ character on the display change to ¥(yen)? -Press ATTN Y N -Press HOLD - Hold the shift key down and press the. (peroid) 038 key on the numeric keyboard. (This ensures that Bad G2 (display) card (see MAP 050 for the 5110 is in EBCDIC character mode.) jumpering). Bad H2 (base I/O) card. Does the 5110 have the KATAKANA feature Bad keyboard PC board (see MIM 251). installed? Check/ replace Z4 (keyboard) cable (see Map Y N 0210 and MIM 206,255).

01JAN79{ ,: EC 836600 PEC 835541 5 P Q R MAP 0900-4 E F M R MACHINE CHECKOUT ABC MAP 0900-5 2 234 222

PAGE 5 OF 13

039 047 -Press the HOLD key. Bad display assembly (see MIM 204). - Hold the shift key down and press the. ""-'II (peroid) key on the numeric keyboard. 048 ( "~ // The vertical frequency may be out of Go to Page 6, Step 050, adjustment (see MIM 247). Entry Point F. ************* * CAUTION * 040 ************* - Release the P key. High voltage is present. -Probe H2-B04 (+typamatic). If this adjustment has no effect; (See appendix B, the general logic probe, in the 5110 MIM). Go To Map 0500, Entry Point A.

Is the UP light on? 049 Y N Go To Map 0500, Entry Point A.

041 - Press and hold the A key -Probe H2-U12 (-keyboard strobe).

Are both lights on and steady? Y N

042 Bad H2 (base I/O) card.

043 Bad keyboard PC board (see MIM 251). Check/ replace Z4 (keyboard) cable (see Map 0210 and MIM 206,255).

044 Bad H2 (base I/O) card.

045 Go To Map 0420, Entry Point A.

046 Bad IN PROCESS light. Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 248,249).

01JAN79

EC 836600 PEC 835541 MAP 0900-5 I MACHINE CHECKOUT s MAP 0900-6

PAGE 6 OF 13

050 056 (Entry Point F) -Check the DISPLAY REGISTERS switch (see MIM 243). / \ Does the machine have a BASIC/APL switch ',,~ _ i' (see MIM 205)? Does the DISPLAY REGISTERS switch Y N function correctly? Y N 051 Go to Step 054, Entry Point B. 057 Bad DISPLAY REGISTERS switch. 052 Bad H2 (base I/O) card. -Check the BASIC/ APL switch (see MIM 246). Bad G2 (display) card (see MAP 050 for jumpering). Does the BASIC/ APL switch function Check/ replace Z3 (display and control panel) correctly? cable (see MAP 0210 and MIM 248,249). Y N If the machine still fails, 053 Go To Map 0500, Entry Point A. Bad BASIC / APL switch. Bad L2 (exec ROS) card (see MAP 050 for 058 jumpering). Do you want to check out the RUN or the Bad H2 (base I/O) card. STEP switch? Check/replace Z3 (display and control panel) Y N cable (see MAP 0210 and MIM 248,249). 059 054 (Entry Point E) (Entry Point B) -Switch the DISPLAY REGISTERS switch to -Press RESTART. NORMAL. -Wait 25 seconds. -Switch the RUN switch under the covers to -Check the REVERSE DISPLAY switch (see MIM RUN. 242). -Check the L32-64-R32 switch (see MIM 244). Does the REVERSE DISPLAY switch function correctly? Does the L32-64-R32 switch function Y N correctly? Y N 055 Bad REVERSE DISPLAY switch. 060 Bad H2 (base I/O) card. Bad L32-64-R32 switch. Bad G2 (display) card (see MAP 050 for Bad H2 (base I/O) card. jumpering). Bad G2 (display) card (see MAP 050 for Check/ replace Z3 (display and control panel) jumpering). cable (see MAP 0210 and MIM 248,249). Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 248,249).

01JAN79

1 EC 836600 PEC 835541 3 7 s T U MAP 0900-6 U MACHINE CHECKOUT v wX MAP 0900-7 6

PAGE 7 OF 13

061 067 -Switch the L32-64-R32 switch to 64. Bad M4 (read/write storage) card. '~'" \1, ( Use the 5110 model number to identify the Bad J2 (processor) card (see MAP 050 for read / write storage size: jumpering).

Model A11,B11,C11 = 16K 068 Model A12,B12,C12 = 32K Bad M2 (read/write storage) card. Model A13,B13,C13 = 48K Bad J2 (processor) card (see MAP 050 for Model A14,B14,C14 = 64K jumpering). Model A21,B21,C21 = 16K Model A22,B22,C22 = 32K 069 Model A23, B23,C23 = 48K -Switch the DISPLAY REGISTERS switch to Model A24, B24,C24 = 64K NORMAL. -Perform a calculation as follows (see the APL or -Check the read/write storage size in the 5110. BASIC reference manual): -Switch the DISPLAY REGISTERS switch to DISPLAY REGISTERS. -For APL, enter: (See DISPLAY REGISTERS in the Diagnostic B+-9 EXECUTE Aids section in the MIM). C+-3 EXECUTE A+-BxC EXECUTE Is the read/write storage size correct? A EXECUTE Y N - For BASIC, enter: 062 B=9 EXECUTE Is the read/write storage size 3FFF? C=3 EXECUTE Y N A=B*C EXECUTE

063 Is the answer 27? Is the read/write storage size 7FFF? Y N Y N 070 064 Is the PROCESS CHECK light on? Is the read/write storage size BFFF? Y N Y N 071 065 Bad L2 (exec ROS) card (see MAP 050 for c Bad N2 (read/write storage) card. jumpering). Bad J2 (processor) card (see MAP Bad F2 (Common and language ROS) card. 050 for jumpering). Bad E4 (APL ROS) card.

066 072 Bad N4 (read/write storage) card. Go To Map 0420, Entry Point A. c Bad J2 (processor) card (see MAP 050 for jumpering).

01JAN79

EC 836600 PEC 835541 8 v wX y MAP 0900-7 • y MACHINE CHECKOUT MAP 0900-8 7

PAGE 8 OF 13

(Step 079 continued) 073 -Observe the IN PROCESS light. Does the audible alarm turn on? -Hold down the COMMAND key and press the 4 Y N key on the alphameric keyboard. - Release the keys. 080 - Press EXECUTE. - Probe J6-D02 (+alarm).

Does the IN PROCESS light turn on or flash? Is the UP light on? • Y N Y N

" 074 081 Did the PROCESS CHECK light turn on or Bad G2 (display) card (see MAP 050 for flash? jumpering). Y N Check/ replace Z3 (display and control panel) cable (see MAP 0210 and MIM 075 248,249). Bad G2 (display) card (see MAP 050 for jumpering). 082 Check/ replace Z3 (display and control panel) 076 cable (see MAP 0210 and MIM 248,249). The leads to the IN PROCESS and PROCESS Bad audible alarm (see MIM 201). CHECK lights are swapped. Use LOGIC 420 to help in metering out the leads. 083 -Press ATTN 077 Does the 5110 have the ALARM feature? Is the alarm off? Y N Y N

078 084 Go to Step 085, Entry Point G. Bad G2 (display) card (see MAP 050 for jumpering). 079 (Entry Point 0) 085 (Entry Point G) Press ATTN. - For APL, enter; Use the keys on the numeric key section of the 2 DCC 1 keyboard (see MIM 250). -Press EXECUTE -Hold CMD and press HOLD -For BASIC, enter; -Hold CMD and press - (minus) 10 WRITE FILE FLS,'S' -Press EXECUTE. When DCP loads, the characters DCP should -Enter RUN appear on the display. (You have loaded DCP , - Press EXECUTE. diagnostic control program. See MIM section (Step 079 continues) 4, diagnostic aids). (Step 085 continues)

01JAN79,f EC 836600 PEC 835541

MAP 0900-8 MACHINE CHECKOUT z MAP 0900-9

PAGE 9 OF 13

(Step 085 continued) 093 Does the DCP program load? -Press C Y N -Press 1 ""'.'~ -Press EXECUTE (. ," 086 Is the PROCESS CHECK light on? Did the PROCESS CHECK light come on? Y N Y N • 087 094 Bad CMD key. TAPE READ DIAGNOSTIC should appear if the 5110 has an internal tape unit (see MIM Go To Map 0600, Entry Point A. 201). DISKETTE READ DIAGNOSTIC should 088 appear if the 5110 does NOT have an Go To Map 0420, Entry Point A. internal tape unit.

089 Do the words TAPE READ DIAGNOSTIC or Put the DCP program in diagnostic mode by DISKETTE READ DIAGNOSTIC appear on uSing the keys on the numeric key section of the the top line of the display? keyboard: Y N

-Hold CMD and press * (BASIC multiply key) 095 OR Bad F2 (Common and language ROS) card. -Hold CMD and press x (APL multiply key) c' 096 The characters DIAG DCP should appear on the You have loaded and are running the tape or display (see MIM section 4, diagnostic aids). diskette read diagnostic program (see MIM section 4, diagnostic aids). Follow the Do t~e characters DIAG DCP appear on the instructions on the display. Return to this displ~y? point for further instructions when DSP Y N MENU is displayed.

090 Is DSP MENU on the display? Is the PROCESS CH ECK light on? Y N Y N 097 091 Is the PROCESS CHECK light on? c Bad L2 (exec ROS) card (see MAP 050 for Y N jumpering). Bad F2 (Common and language ROS) card. 098 Bad E4 (APL RDS) card. Did the tape or diskette read diagnostic program load? C:I 092 Y N Go To Map 0420, Entry Point A.

01JAN79 1 1 1 1 1 3 0 0 0 0 EC 836600 PEC 835541 A A A A A z ABC D E MAP 0900-9 I A A A A MACHINE CHECKOUT MAP 0900-10 BCD E 999 9 PAGE 10 OF 13

099 Bad F2 (Common and language ROS) card. Bad H2 (base I/O) card.

100 Does the 5110 have an internal tape drive (see MIM 201)? .. V N

101 Go To Map 0310, Entry Point A.

102 Go To Map 0300, Entry Point A.

103 Go To Map 0420, Entry Point A.

104 Does the 5110 have an internal tape drive (see MIM 201)? V N

105 -Enter 881 -Press EXECUTE

Follow the instructions on the display, then return to this point for further instructions when the MOl is completed. (You have loaded and are running the diskette diagnostic program. See section 4, diagnostic aids).

Did the MOl run to completion? V N

106 Perform the actions requested by the routine.

01JAN79 1 1 1 1 EC 836600 PEe 835541 A A F G MAP 0900-10 A A MACHINE CHECKOUT MAP 0900-11 F G 'I, 1 1 ","', o 0 ( PAGE 11 OF 13

107 - Press A TIN twice.

('- The DSP menu should now be displayed. Select each routine one at a time until you have completed all the routines that are applicable to the features on your machine (see section 4, diagnostic aids).

"" or,!, -Printer MOl 800 ( _.... ,/ -Async comm-serial I/O MOl 820 -BSCA MOl 821 -Parallel I/O MOl 823 -Communications routine chart 890

Do the routines run correctly? Y N

108 Preform the actions requested by the routines.

109 c The machine checkout is complete. Remove the diagnostic diskette and press RESTART.

110 -Enter 860 - Press EXECUTE.

Follow the instructions on the display then return to this point for further instructions when the MDI is completed. (You have loaded and are running the tape write diagnostic program. See MIM section 4, DIAGNOSTIC AIDS).

Did MDI 860 run correctly? Y N .' 111 Perform the actions requested by the routines.

01JAN79 ()~I 1 2 EC 836600 PEC 835541 A H MAP 0900-11 • A MACHINE CHECKOUT A A A MAP 0900-12 H K L M 1 1 PAGE 12 OF 13

112 117 Do you want to run the tape magnet select The machine checkout is complete. routine? Remove the 5110 diagnostic tape cartridge Y N and press RESTART.

113 118 (Entry Point H) -Remove the 5110 diagnostic tape cartridge. - Press A TIN three times (until DIAG DCP Use the keys on the numeric keyboard appears). -Hold CMD and press HOLD -Press EXECUTE. -Hold CMD and press - (minus) - Follow the instructions on the display but -Hold CMD and press * (BASIC multiply key) insert the communications diagnostic tape OR cartridge. -Hold CMD and press x (APL multiply key) -Press C Is DSP MENU on the display? -Press 0 Y N -'Press EXECUTE 119 The DSP MENU should now be displayed. Go To Map 0300, Entry Point A. Select each routine one at a time until you have completed all of the routines that are 120 applicable to the features available on your -Select the routines which apply to the machine (see section 4, diagnostic aids). features on your machine.

-PRINTER MDI 800 Do the routines run correctly? -AUXILIARY TAPE MDI 840 Y N -TAPE WRITE MDI 860 -DISKETTE MDI 881 121 Perform the actions requested by the Is the PROCESS CHECK light on? routine. Y N 122 114 The communications feature checkout is Do the routines run correctly? complete. , Remove the communications Y N diagnostic tape cartridge and press RESTART.

115 123 Perform the actions requested by the Go To Map 0420, Entry Point A. routines.

116 Do you wish to check out the Async / ' comm-serial I/O feature ,the BSCA feature, or the PARALLEL I/O feature? Y N

01JAN79 1 3 EC 836600 PEC 835541 A A A A J K L M MAP 0900-12 T A A MACHINE CHECKOUT A A A MAP 0900-13 6 A J N P Q 9 1 2 PAGE 13 OF 13

124 130 - Press RESTART - Probe H6A04 (+single instr switch comm). - Do the test at the end of the Select Magnet Service Check (see MIM 221). Is the UP light on? Y N Is the tape motion rhythmic? Y N 131 Bad H2 (base I/O) card. 125 Check/ replace Z3 (display and control Do the FORWARD AND REVERSE panel) cable (see MAP 0210 and MIM SELECT MAGNETS SERVICE CHECK 248,249). (see MIM 221). 132 126 Bad J2 (processor) card (see MAP 050 for - Remove the scratch tape. jumpering). -Insert the diagnostic tape. Bad RUN switch (see MIM 201,249). Check/ replace Z3 (display and control Go to Page 12, Step 113, Entry Point H. panel) cable (see MAP 0210 and MIM 248,249). 127 Bad STEP switch Go To Map 0420, Entry Point A. 133 128 Go to Page 6, Step 059, Entry Point E. c -Switch the RUN switch under the covers to NOT RUN. 134 -Switch the DISPLAY REGISTERS switch to Bad RUN switch (see MIM 201,249). DISPLAY REGISTERS. Check/ replace Z3 (display and control panel) -Observe the display. cable (see MAP 0210 and MIM 248,249).

Is any of the information in the registers changing? Y N

129 '.. -Press the STEP switch.

I' CJ' Did ROLO change? (See DISPLAY REGISTERS in the Diagnostic Aids section in the MIM). Y N c

01JAN79

EC 836600 PEC 835541 A A A N P Q MAP 0900-13 I This page intentionally left blank.

~ ..

MAP 0900-14 - :"' ~ '''<""' ,~ n ~ ;#' o o , "'" ~ ~ READER'S COMMENT FORM

Please use this form only to identify publication errors or request changes to publications. Technical questions about IBM systems, changes in I BM programming S:m ~.s: support, requests for additional publications, etc, should be directed to your IBM representative or to the IBM branch office nearest your location. ~ (11 (I) ... :::I ... Error in publication (typographical, illustration, and so on). No reply. Inaccurate or misleading information in this publication. Please tell us ~ 0 (") CI) about it by using this postage-paid form. We will correct or clarify the (I) -< »~ Page Number Error publication, or tell you why a change is not being made, provided you :::I (I) Q) 3 include your name and address. < ~. ~ Page Number Comment (3 (") (I)a. I:

~

..

'III en -< Co)... 6 (11 (11 Co) IBM may use and distribute any of the information you supply in any way ~ it believes appropriate without incurring any obligation whatever. You may, Name ______of course, continue to use the information you supply. Address

• No postage necessary if mailed in the U.S.A. +I I SY31-0553-2

Fold Fold

FIRST CLASS 111111 PERMIT NO. 40 ARMONK, N. Y. CD s: ~ ~ 0 (/) BUSINESS REPLY MAil -< !!:. CD NO POSTAGE STAMP NECESSARY IF MAILED IN THE UNITED STATES 3 s: Q) POSTAGE Will BE PAID BY •.• ....5' CD ::I Q) ::I n CD » ::I Q) I BM Corporation < General Systems Division ~. Development Laboratory \J na CD Pu bl ications, Dept. 245 Q. Rochester, Minnesota 55901 m~

~ ::I.... CD Q. Fold 5' Fold c en ~ ------(/) ------W-< - - <, - --- ~ l ------_o- ~ f!; 6 U'I J International Business Machines Corporation U'I W ~ General Systems Division 4111 Northside Parkway N.W. P.O. Box 2150 Atlanta, Georgia 30301 (U.S.A. only)

General Business Group/International 44 South Broadway White Plains, New York 10601 U.S.A. (International)

, ·c

~I 0 o II o o • ------International Business Machines Corporation

General Systems Division 4111 Northside Parkway N.W. P.O. Box 2150 Atlanta, Georgia 30301 o (U.S4~.only)

General Business Group/International 44 South Broadway White Plains, New York 10601 (,) U.S.A. (I nte rnational ) f

'"t ,C)

iii ~ ~ 0-- en ~ ...CD 3 ~ OJ ~ ...5' I, , I CD ::l OJ ::l C') CD » ::l OJ ~ iii' a"tI C') CD 0- ~ ~

~ ~ CD 0- 5' c ~, en ( I "J ~ ".l , , en -< ~ 6 U'1 U'1 W ~ ") ( ,II"

(J SY31-0553-2 I I I I 1 1 ------_------.- International Business Machines Corporation

General Systems Division 4111 Northside Parkway !'I.W. P.O. Box 2150 Atlanta, Georgia 30301 (U.S_A. only)

General Business Group/International 44 South Broadway White Plains, New York 10601 U.S.A. (International)

iii :!: U1- 0 en '< ~ ::l 2!.. '< ;nen .

~ na

~ ::l ...CO Co 3· c en ?> en • w-< 6- U1 U1 W ~

I I I I , I I SY31-0553-2 I I I I I I 1 I 1