DOCSLIB.ORG

Mellanox Flexboot for Connectx®-3 /Connectx®-3 Pro Release Notes

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Mellanox Flexboot for Connectx®-3 /Connectx®-3 Pro Release Notes Mellanox FlexBoot for ConnectX®-3 /ConnectX®-3 Pro Release Notes Rev 3.4.752 www.mellanox.com Mellanox Technologies NOTE: THIS HARDWARE, SOFTWARE OR TEST SUITE PRODUCT (“PRODUCT(S)”) AND ITS RELATED DOCUMENTATION ARE PROVIDED BY MELLANOX TECHNOLOGIES “AS-IS” WITH ALL FAULTS OF ANY KIND AND SOLELY FOR THE PURPOSE OF AIDING THE CUSTOMER IN TESTING APPLICATIONS THAT USE THE PRODUCTS IN DESIGNATED SOLUTIONS. THE CUSTOMER'S MANUFACTURING TEST ENVIRONMENT HAS NOT MET THE STANDARDS SET BY MELLANOX TECHNOLOGIES TO FULLY QUALIFY THE PRODUCT(S) AND/OR THE SYSTEM USING IT. THEREFORE, MELLANOX TECHNOLOGIES CANNOT AND DOES NOT GUARANTEE OR WARRANT THAT THE PRODUCTS WILL OPERATE WITH THE HIGHEST QUALITY. ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES FOR ANY DIRECT, INDIRECT, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES OF ANY KIND (INCLUDING, BUT NOT LIMITED TO, PAYMENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY FROM THE USE OF THE PRODUCT(S) AND RELATED DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Mellanox Technologies 350 Oakmead Parkway Suite 100 Sunnyvale , CA 94085 U.S.A. www.mellanox.com Tel: (408) 970-3400 Fax: (408) 970-3403 © Copyright 2017. Mellanox Technologies Ltd . All Rights Reserved . Mellanox®, Mellanox logo, Accelio®, BridgeX®, CloudX logo, CompustorX® , Connect-IB®, ConnectX® , CoolBox®, CORE-Direct®, EZchip®, EZchip logo, EZappliance®, EZdesign®, EZdriver®, EZsystem®, GPUDirect®, InfiniHost®, InfiniBridge®, InfiniScale®, Kotura®, Kotura logo, Mellanox CloudRack® , Mellanox CloudXMellanox® , Mellanox Federal Systems® , Mellanox HostDirect® , Mellanox Multi-Host®, Mellanox Open Ethernet®, Mellanox OpenCloud® , Mellanox OpenCloud Logo® , Mellanox PeerDirect® , Mellanox ScalableHPC® , Mellanox StorageX® , Mellanox TuneX® , Mellanox Connect Accelerate Outperform logo , Mellanox Virtual Modular Switch®, MetroDX®, MetroX®, MLNX-OS®, NP-1c®, NP-2®, NP-3®, NPS®, Open Ethernet logo, PhyX®, PlatformX®, PSIPHY®, SiPhy®, StoreX®, SwitchX®, Tilera®, Tilera logo, TestX®, TuneX®, The Generation of Open Ethernet logo , UFM®, Unbreakable Link® , Virtual Protocol Interconnect® , Voltaire® and Voltaire logo are registered trademarks of Mellanox Technologies , Ltd. All other trademarks are property of their respective owners . For the most updated list of Mellanox trademarks, visit http://www.mellanox.com/page/trademarks Doc #: N/A Mellanox Technologies 2 Table of Contents Table of Contents . 3 List Of Tables . 5 Release Update History . 6 Chapter 1 Overview . 7 1.1 Supported Adapter Cards and Firmware . 7 1.2 Supported Tools (MFT). 7 1.3 Supported Operating Systems. 7 1.4 Tested Platforms. 8 Chapter 2 Changes and New Features in Rev 3.4.746 . 9 Chapter 3 Known Issues . 10 Chapter 4 Bug Fixes History . 16 Chapter 5 Changes and New Feature History . 20 Rev 3.4.752 Mellanox Technologies 3 List Of Tables Table 1: Release Update History . 6 Table 2: Supported Adapter Cards and Firmware . 7 Table 3: Supported Tools (MFT) . 7 Table 4: Supported Operating Systems . 7 Table 5: Tested Platforms . 8 Table 6: Changes and New Features. 9 Table 7: Known Issues . .10 Table 8: Fixed Bugs List . .16 Table 9: Changes and New Feature History . .20 Rev 3.4.752 Mellanox Technologies 5 Release Update History Table 1 - Release Update History Release Date Description Rev 3.4.752 October 19, 2017 Initial release of this FlexBoot version for Con- nectX-3/ConnectX-3 Proadapter cards. 6 Mellanox Technologies Rev 3.4.752 Overview 1Overview These are the release notes for "Mellanox FlexBoot", the software for Boot over Mellanox Tech- nologies adapter devices supporting VPI. FlexBoot enables booting kernels or operating systems (OS) from remote servers in compliance with the PXE specification. This package is based on the open source project iPXE available at http://www.ipxe.org. 1.1 Supported Adapter Cards and Firmware Table 2 - Supported Adapter Cards and Firmware Adapter Cards Firmware Version ConnectX-3 Pro 2.42.5000 ConnectX-3 2.42.5000 1.2 Supported Tools (MFT) Table 3 - Supported Tools (MFT) Tools Version MFT (Mellanox Firmware Tools) 4.7.0 1.3 Supported Operating Systems All the Operating Systems below expect for RedHat 7.3 are supported in Ethernet protocol only. RedHat 7.3 is supported in both InfiniBand and Ethernet protocol. Table 4 - Supported Operating Systems OSs Version ESXi 5.5 ESXi 6.0 ESXi 6.5 RHEL 6.4 RHEL 6.6 RHEL 7.0 RHEL 7.1 RHEL 7.2 RHEL 7.3 SLES 11.3 SLES 11.4 Rev 3.4.752 Mellanox Technologies 7 Table 4 - Supported Operating Systems OSs Version SLES 12 SLES 12.1 SLES 12.2 Ubuntu 14.04 Ubuntu 15.4 Ubuntu 16.04 Ubuntu 16.10 Windows Server 2012 Windows Server 2012 R2 Windows Server 2016 1.4 Tested Platforms Table 5 - Tested Platforms Vendor Type of server Bios Version DELL Dell PowerEdge R730xd 13G 2.3.4 DELL Dell PowerEdge R630 13G 2.3.4 DELL Dell PowerEdge R640 14G 0.3.6 DELL Dell PowerEdge C6320p 1.1.3 Quanta Yesomity F20_3A12 / F20_3A09 Quanta Leopard AVA_3B08 Supermicro SuperMicro X9DRW V3.2 Dell PowerEdgeR820 1.6.6 HPE ProLiant DL180 Gen9 U20 v2.20 (05/05/2016) HPE ProLiant XL730f Gen9 U18 v1.50 (08/04/2015) HPE ProLiant DL380 Gen9 P89 v2.20 (06/02/2016) HPE ProLiant XL260a Gen9 U24 v1.00 (05/18/2016) HPE ProLiant DL160 Gen9 U20 v2.20 (05/05/2016) HPE ProLiant DL360 Gen10 U32 v1.00 (12/31/2016) Lenovo 3650 M5 2.10 TCE124M (23/06/2016) Lenovo 3650 M5 1.20 TCE108IUS (17/12/2015) Lenovo 3550 M5 1.20 TCE108IUS (17/12/2015) 8 Mellanox Technologies Rev 3.4.752 Changes and New Features in Rev 3.4.746 2 Changes and New Features in Rev 3.4.746 Table 6 - Changes and New Features Category Description Secure Firmware Update Added support for Secure Firmware Update FlexBoot Boot Enabled booting Grub 2.02 over IB SOL Disabled SOL by default Rev 3.4.752 Mellanox Technologies 9 3 Known Issues The following is a list of general limitations and known issues of the various components of this FlexBoot release. Table 7 - Known Issues Internal Ref. Description - Description: Several BIOS vendors have limited boot-vector space and may not display FlexBoot in their boot menu. WA: Disable the embedded NIC boot agent in BIOS Keywords: BIOS - Description: In several BIOS, the server might hang during FlexBoot booting due to wrong configuration of the PMM. WA: N/A Keywords: BIOS - Description: Only EBX, ESI, DS, ES registers can be saved in Boot Entry. WA: N/A Keywords: BIOS - Description: If a client returned control to the BIOS after a successful connection to an iSCSI target (but did not boot from it), then, unexpected behavior may occur. WA: Follow the instructions described in the FlexBoot UM for the proper iSCSI boot/ install Keywords: BIOS 673114/821899 Description: FlexBoot banner might not be shown in some BIOSes. WA: N/A Keywords: BIOS - Description: Firmware 2.30.3000 and below does not support booting over Ethernet with VPI adapter cards when using QSFP cables (40GE, hybrid cables). WA: N/A Keywords: PXE Boot - Description: Booting from WDS running on Windows 2008 R2 in InfiniBand mode, is currently not supported due to compatibility issues between FlexBoot 3.4.142 and Mella- nox WinOF v4.40 and below. WA: N/A Keywords: PXE Boot 10 Mellanox Technologies Rev 3.4.752 Known Issues Table 7 - Known Issues Internal Ref. Description - Description: In some cases, PXE boot will not work if the client was given only the file- name without next-server (siaddr). WA: N/A Keywords: PXE Boot - Description: PXE boot after iSCSI boot with static configuration is currently not sup- ported. WA: N/A Keywords: PXE Boot - Description: Boot over VLAN with IB port is currently not supported. WA: N/A Keywords: PXE Boot - Description: Some faulty boot loaders do not close the underlying UNDI device which may result in unexpected behavior and possible system crash after the OS starts to load. WA: N/A Keywords: PXE Boot - Description: Chain-loading gPXE stack may result in undesirable behavior. WA: N/A Keywords: PXE Boot 647143 Description: Executing a partial boot loop while only downloading the NBP and select- ing localboot is unsupported and may cause undefined behavior. WA: N/A Keywords: PXE Boot 670421 Description: Since only a single Boot Entry Vector (BEV) per PCI Physical Function is supported, disabling the first port causes the second port to disappear as well. WA: N/A Keywords: PXE Boot - Description: iSCSI over IB is not tested. WA: N/A Keywords: iSCSI Rev 3.4.752 Mellanox Technologies 11 Table 7 - Known Issues Internal Ref. Description - Description: iSCSI over DCB is not supported. WA: N/A Keywords: iSCSI - Description: FlexBoot supports only a single active iSCSI connection. Thus, when iSCSI-boot via Port 1 succeeds to connect but fails to boot, it will fail to connect via Port 2. WA: N/A Keywords: iSCSI - Description: Boot retries is currently not functional when booting from iSCSI. WA: N/A Keywords: iSCSI 655800 Description: IPv6 is not supported. WA: N/A Keywords: iSCSI - Description: Boot menu is displayed as READ ONLY if the HCA card does not support flash configuration. WA: N/A Keywords: User Interface - Description: FlexBoot Boot Menu will not be visible in serial output. WA: N/A Keywords: User Interface - Description: Large Receive Offload (LRO) and iSCSI may not interoperate due to a bug in current Linux kernel distributions.
Load more

Recommended publications
  • Boot Mode Considerations: BIOS Vs UEFI
    Boot Mode Considerations: BIOS vs. UEFI An overview of differences between UEFI Boot Mode and traditional BIOS Boot Mode Dell Engineering June 2018 Revisions Date Description October 2017 Initial release June 2018 Added DHCP Server PXE configuration details. The information in this publication is provided “as is.” Dell Inc. makes no representations or warranties of any kind with respect to the information in this publication, and specifically disclaims implied warranties of merchantability or fitness for a particular purpose. Use, copying, and distribution of any software described in this publication requires an applicable software license. Copyright © 2017 Dell Inc. or its subsidiaries. All Rights Reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be the property of their respective owners. Published in the USA [1/15/2020] [Deployment and Configuration Guide] [Document ID] Dell believes the information in this document is accurate as of its publication date. The information is subject to change without notice. 2 : BIOS vs. UEFI | Doc ID 20444677 | June 2018 Table of contents Revisions............................................................................................................................................................................. 2 Executive Summary ............................................................................................................................................................ 4 1 Introduction ..................................................................................................................................................................
    [Show full text]
  • UEFI PXE and Ipxe Alternative Approaches to PXE Booting
    Installing ESXi Using PXE n gPXELINUX is a hybrid configuration that includes both PXELINUX and gPXE and supports booting from a Web server. gPXELINUX is part of the SYSLINUX package. If you use gPXELINUX to boot the ESXi installer, only the gpxelinux.0 binary file, mboot.c32, and the configuration file are transferred via TFTP. The remaining files are transferred via HTTP. HTTP is typically faster and more reliable than TFTP, especially for transferring large amounts of data on a heavily loaded network. NOTE VMware currently builds the mboot.c32 plugin to work with SYSLINUX version 3.86 and tests PXE booting only with that version. Other versions are likely to be incompatible. This is not a statement of limited support. For support of third-party agents that you use to set up your PXE booting infrastructure, contact the vendor. UEFI PXE and iPXE Most UEFI firmware natively includes PXE support that allows booting from a TFTP server. The firmware can directly load the ESXi boot loader for UEFI systems, mboot.efi. Additional software such as PXELINUX is not required. iPXE can also be useful for UEFI systems that do not include PXE in firmware and for older UEFI systems with bugs in their PXE support. For such cases you can try installing iPXE on a USB flash drive and booting from there. NOTE Apple Macintosh products do not include PXE boot support. They include support for network booting via an Apple-specific protocol instead. Alternative Approaches to PXE Booting Alternative approaches to PXE booting different software on different hosts are also possible, for example: n Configuring the DHCP server to provide different initial boot loader filenames to different hosts depending on MAC address or other criteria.
    [Show full text]
  • PXE Network Boot Methods
    PXE network boot methods Luc Sarzyniec <[email protected]> 2013-02-21 Contents 1 Introduction to PXE boot 2 1.1 Boot over the network procedure . 2 1.2 The PXE specifications . 2 1.3 Network Bootstrap Programs . 2 1.4 Configure a specific NBP on DHCP server . 2 1.4.1 ISC DHCP server . 2 1.4.2 dhcpcd . 2 1.4.3 dnsmasq . 2 2 Network Bootstrap Programs 3 2.1 PXElinux . 3 2.2 GPXElinux . 3 2.3 iPXE . 4 2.4 GRUB2 disk . 5 2.5 Comparison of NBPs . 6 3 Install and configure NBPs 6 3.1 PXElinux/GPXElinux . 6 3.2 iPXE . 6 3.2.1 Boot a iPXE NBP from DHCP . 6 3.2.2 Create an iPXE ROM to be burned on a NIC's PROM 7 3.2.3 Load iPXE from GNU/GRUB . 7 3.3 GRUB2 disk . 9 4 Boot nodes following a node-specific profile 10 4.1 PXElinux/GPXElinux (core feature) . 10 4.2 iPXE (custom feature) . 11 4.3 GRUB2 disk (custom feature) . 12 1 5 Download and boot Operating System kernel 13 5.1 PXElinux . 13 5.2 GPXElinux . 14 5.3 iPXE . 14 5.4 GRUB2 disk . 15 6 Boot local Operating System (from hard disk) 16 6.1 chain.c32 COMBOOT . 16 6.1.1 PXElinux/GPXElinux . 16 6.1.2 iPXE . 16 6.2 GRUB2 disk . 17 7 Chaining NBPs 17 7.1 From PXElinux to GRUB2 disk . 18 7.2 From PXElinux to iPXE . 18 7.3 From iPXE to PXElinux .
    [Show full text]
  • Netbooting Microsoft Windows 7 and XP
    Netbooting Microsoft Windows 7 and XP Chris Holman∗ Centre for Advanced Internet Architectures, Technical Report 130226A Swinburne University of Technology Melbourne, Australia [email protected] Abstract—This tutorial shows how to set up Microsoft and testing the Windows PE are detailed in Section VI. Windows 7 and XP to be booted using network attached Installing to the iSCSI drive is covered in Section VII. storage. iSCSI support is built in to a Windows 7 installer The report concludes with Section IX and an appendix. using the Windows 7 Automated Installation Kit. DHCP, an iSCSI server and a TFTP server are configured on the II. BACKGROUND server to provide a PXE client and an iSCSI target. Once A. DHCP set up, a client PC will be able to operate entirely without a local disk. Dynamic Host Configuration Protocol’s (DHCP) [2] Index Terms—Windows 7, Windows XP, PXE, netboot- primary purpose is to assign IP addresses and other ing network configuration details to hosts. It is used in this tutorial for the purposes of providing network and PXE I. INTRODUCTION booting configuration details, including TFTP server PXE (“Preboot eXecution Environment”) [1] booting, settings and configuration filenames. or net booting, can be used to load an operating system B. TFTP over the network without using the local hard drive. While FreeBSD and Linux Operating Systems (OSes) Trivial File Transfer Protocol (TFTP) [3] is a simple support a number of different PXE boot methods (includ- protocol to transfer files. It is commonly used in PXE ing NFS, TFTP, HTTP, iSCSI and more), Windows only scenarios because of its simplicity.
    [Show full text]
  • Vmware Esxi Installation and Setup
    VMware ESXi Installation and Setup 17 APR 2018 VMware vSphere 6.7 VMware ESXi 6.7 VMware ESXi Installation and Setup You can find the most up-to-date technical documentation on the VMware website at: https://docs.vmware.com/ If you have comments about this documentation, submit your feedback to [email protected] VMware, Inc. 3401 Hillview Ave. Palo Alto, CA 94304 www.vmware.com Copyright © 2018 VMware, Inc. All rights reserved. Copyright and trademark information. VMware, Inc. 2 Contents 1 About VMware ESXi Installation and Setup 4 2 Introduction to vSphere Installation and Setup 5 3 Overview of the vSphere Installation and Setup Process 6 4 About ESXi Evaluation and Licensed Modes 9 5 Installing and Setting Up ESXi 10 ESXi Requirements 10 Preparing for Installing ESXi 19 Installing ESXi 70 Setting Up ESXi 188 After You Install and Set Up ESXi 208 6 Troubleshooting ESXi Booting 212 Host Stops Unexpectedly at Bootup When Sharing a Boot Disk with Another Host 212 Host Fails to Boot After You Install ESXi in UEFI Mode 213 7 Decommission an ESXi Host 214 VMware, Inc. 3 About VMware ESXi Installation and Setup 1 VMware ESXi Installation and Setup describes how to install and configure VMware ESXi™. Intended Audience VMware ESXi Installation and Setup is intended for experienced administrators who want to install and configure ESXi. This information is written for experienced Windows or Linux system administrators who are familiar with virtual machine technology and data center operations. The information about using the Image Builder ® and VMware vSphere Auto Deploy™ is written for administrators who have experience with Microsoft ® PowerShell and VMware vSphere PowerCLI™.
    [Show full text]
  • Mellanox PXE Remote Installation User Guide Rev 1.3
    Mellanox PXE Remote Installation User Guide Rev 1.3 www.mellanox.com Mellanox Technologies Confidential Rev 1.3 Contents NOTE: THIS HARDWARE, SOFTWARE OR TEST SUITE PRODUCT (“PRODUCT(S)”) AND ITS RELATED DOCUMENTATION ARE PROVIDED BY MELLANOX TECHNOLOGIES “AS-IS” WITH ALL FAULTS OF ANY KIND AND SOLELY FOR THE PURPOSE OF AIDING THE CUSTOMER IN TESTING APPLICATIONS THAT USE THE PRODUCTS IN DESIGNATED SOLUTIONS. THE CUSTOMER'S MANUFACTURING TEST ENVIRONMENT HAS NOT MET THE STANDARDS SET BY MELLANOX TECHNOLOGIES TO FULLY QUALIFY THE PRODUCT(S) AND/OR THE SYSTEM USING IT. THEREFORE, MELLANOX TECHNOLOGIES CANNOT AND DOES NOT GUARANTEE OR WARRANT THAT THE PRODUCTS WILL OPERATE WITH THE HIGHEST QUALITY. ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON INFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES FOR ANY DIRECT, INDIRECT, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES OF ANY KIND (INCLUDING, BUT NOT LIMITED TO, PAYMENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY FROM THE USE OF THE PRODUCT(S) AND RELATED DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Mellanox Technologies, Inc. 350 Oakmead Parkway Suite 100 Sunnyvale, CA 94085 U.S.A. www.mellanox.com Tel: (408) 970-3400 Fax: (408) 970-3403 © Copyright 2012. Mellanox Technologies. All rights reserved. Mellanox®, BridgeX®, ConnectX®, CORE-Direct®, InfiniBridge®, InfiniHost®, InfiniScale®, PhyX®, SwitchX®, Virtual Protocol Interconnect® and Voltaire® are registered trademarks of Mellanox Technologies, Ltd.
    [Show full text]
  • Acquisition and Analysis of Compromised Firmware
    View metadata, citation and similar papers at core.ac.uk brought to you by CORE provided by Elsevier - Publisher Connector Digital Investigation 12 (2015) S50eS60 Contents lists available at ScienceDirect Digital Investigation journal homepage: www.elsevier.com/locate/diin DFRWS 2015 Europe Acquisition and analysis of compromised firmware using memory forensics * Johannes Stüttgen , Stefan Vomel,€ Michael Denzel Department of Computer Science, Friedrich-Alexander University of Erlangen-Nuremberg, Martensstraße 3, 91058 Erlangen, Germany abstract Keywords: To a great degree, research in memory forensics concentrates on the acquisition and Memory forensics analysis of kernel- and user-space software from physical memory to date. With the sys- Memory acquisition tem firmware, a much more privileged software layer exists in modern computer systems Live forensics though that has recently become the target in sophisticated computer attacks more often. Firmware rootkits Compromise strategies used by high profile rootkits are almost completely invisible to Incident response standard forensic procedures and can only be detected with special soft- or hardware mechanisms. In this paper, we illustrate a variety of firmware manipulation techniques and propose methods for identifying firmware-level threats in the course of memory forensic investigations. We have implemented our insights into well-known open-source memory forensic tools and have evaluated our approach within both physical and virtual environments. © 2015 The Authors. Published by Elsevier
    [Show full text]
  • Trenchboot DRTM Features for AMD Platforms
    TrenchBoot DRTM features for AMD platforms Open Source Firmware Conference 2020 Piotr Król 1 / 27 whoami Piotr Król 3mdeb Founder coreboot contributor and maintainer 12yrs in business Conference speaker and organizer 6yrs in Open Source Firmware Trainer for military, government and C-level positions in industrial organizations Former Intel BIOS SW Engineer Open Source Firmware Conference 2020 CC BY | Piotr Król 2 / 27 Kudos NLNet Daniel P. Smith (Apertus Solutions) Andrew Cooper (Citrix) Amazing 3mdeb Embedded Firmware Team, especially: Michał Żygowski Krystian Hebel Norbert Kamiński Open Source Firmware Conference 2020 CC BY | Piotr Król 3 / 27 Goal Explain how TrenchBoot features can be leveraged on AMD- based platforms S-CRTM is challenging What is TrenchBoot and how it work What is Dasharo and how we use it to deploy TrenchBoot What operation improvements, security features and use cases modern OSF can provide for you Open Source Firmware Conference 2020 CC BY | Piotr Król 4 / 27 S-CRTM S-CRTM (Static-Code Root of Trust for Measurement) initial measurement established by static code component (e.g. SoC BootROM, read-only bootblock) this code is typically not updatable Commercial use cases (Silicon Vendor Security Technologies): Intel Boot Guard, AMD HVB, NXP HAB Intel/IBV/UEFI Secure Boot Microsoft BitLocker Open source use cases: coreboot+TrustedGRUB2, Dasharo+LUKS2 Problems requires reboot to reestablish trust requires NDA with SV and skilled personnel to perform task most hardware vendors do not implement it correctly not standardized
    [Show full text]
  • PXE Configuration Utility Help Symantec™ PXE Configuration Utility User Guide
    PXE Configuration Utility Help Symantec™ PXE configuration Utility User Guide Legal Notice Copyright © 2018 Symantec Corporation. All rights reserved. Symantec, the Symantec Logo, the Checkmark Logo are trademarks or registered trademarks of Symantec Corporation or its affiliates in the U.S. and other countries. Other names may be trademarks of their respective owners. This Symantec product may contain third party software for which Symantec is required to provide attribution to the third party (“Third Party Programs”). Some of the Third Party Programs are available under open source or free software licenses. The License Agreement accompanying the Software does not alter any rights or obligations you may have under those open source or free software licenses. Please see the Third Party Legal Notice Appendix to this Documentation or TPIP ReadMe File accompanying this Symantec product for more information on the Third Party Programs. The product described in this document is distributed under licenses restricting its use, copying, distribution, and decompilation/reverse engineering. No part of this document may be reproduced in any form by any means without prior written authorization of Symantec Corporation and its licensors, if any. THE DOCUMENTATION IS PROVIDED "AS IS" AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID. SYMANTEC CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, PERFORMANCE, OR USE OF THIS DOCUMENTATION. THE INFORMATION CONTAINED IN THIS DOCUMENTATION IS SUBJECT TO CHANGE WITHOUT NOTICE.
    [Show full text]
  • Paper Is Organized As Follows
    Bare-Metal Container --- Direct execution of a container image on a remote machine with an optimized kernel --- Kuniyasu Suzaki, Hidetaka Koie, Ryousei Takano National Institute of Advanced Industrial Science and Technology { k.suzaki | koie-hidetaka | takano-ryousei }@aist.go.jp Abstract— Container technology has become popular in HPC based on system-centric architecture which is led by providers applications because it offers easy customization and quick and does not allow changes to the kernel and its settings. execution. However, container technology does not allow kernel- level optimization. It does not allow changing a kernel as well as Even if a user wants to run a Docker image on a real or loading/unloading a kernel module, thus it prevents the virtual machine, it is not so easy because normal Docker image extraction of full performance on a target machine. In addition, does not have a Linux kernel and a bootloader. Although the container technology is designed for multi-tenancy and makes user can install these two components on a Docker image, it difficult to measure exact performance and power consumption will not boot on a real or virtual machine because it does not for an application on a target machine. offer a physical disk image and the bootloader cannot setup the Bare-Metal Container (BMC) solves these problems by a MBR (Master Boot Record). The user has to make a proper mechanism that offers a suitable kernel for a container image root file system on a physical or virtual disk and setup a and boots it on a remote physical machine.
    [Show full text]
  • Cobbler Documentation Release 2.8.5
    Cobbler Documentation Release 2.8.5 Jörgen Maas Nov 19, 2020 Contents 1 About 3 1.1 Release Notes.........................................3 1.2 Distribution Support......................................5 1.3 Distribution Notes.......................................7 1.4 How We Model Things..................................... 13 2 Installation 15 2.1 Prerequisites.......................................... 15 2.2 Installing from packages.................................... 16 2.3 Installing from Source..................................... 18 2.4 Configuration Files....................................... 20 2.5 Relocating your installation.................................. 21 3 General 23 3.1 Cobbler Primitives....................................... 23 3.2 Cobbler Direct Commands................................... 54 3.3 Cobbler Settings........................................ 69 3.4 Managing Services with Cobbler............................... 90 3.5 Kickstart Templating...................................... 94 3.6 Snippets............................................ 102 3.7 Package Management and Mirroring............................. 112 3.8 File System Information.................................... 114 4 Advanced 119 4.1 Advanced Networking..................................... 119 4.2 SELinux............................................ 122 4.3 Configuration Management.................................. 123 4.4 Extending cobbler....................................... 131 4.5 Power Management...................................... 135 4.6
    [Show full text]
  • Session 4 – Goodbye PXE, Hello HTTP Boot Dong Wei, HP Agenda
    LinuxCon Europe UEFI Mini-Summit 7 October 2015 Session 4 – Goodbye PXE, Hello HTTP Boot Dong Wei, HP Agenda • Challenges of Firmware in the Data Center • PXE and HTTP Boot • UEFI Shell Scripting • Data Center Manageability: Redfish and REST APIs • Putting it all together: HP* ProLiant* Servers • Summary and Q&A LinuxCon EU 2015 www.uefi.org 2 Agenda • Challenges of Firmware in the Data Center • PXE and HTTP Boot • UEFI Shell Scripting • Data Center Manageability: Redfish and REST APIs • Putting it all together: HP* ProLiant* Servers • Summary and Q&A LinuxCon EU 2015 www.uefi.org 3 Firmware Challenges In The Data Center Bare Metal Firmware Firmware Deployment Provisioning Updates Configuration Automation Security Scalability Eco-system LinuxCon EU 2015 www.uefi.org 4 The UEFI Solution • Pre-Boot networking • Firmware • IPv4, IPv6 TCP/UDP Management Protocol • Capsule updates Bare Metal • PXE, iSCSI, HTTP, Firmware Provisioning FTP Updates • Boot device selection • Human Interface Infrastructure (HII) • Boot order control • Platform-To-Driver Configuration (CLP) • REST Protocol • OS install & recovery Firmware Deployment Configuration • New hardware abstraction with • UEFI Shell UEFI protocols • Scripting language • UEFI driver model • UEFI device path Automation Scalability LinuxCon EU 2015 www.uefi.org 5 The UEFI Solution • Secure Boot and driver signing • Security technologies (OpenSSL®, RNG, etc…) • Encrypted disks and key management • Interoperability with TCG standards Security • Standards (UEFI Forum) • Compliance: Self Certification
    [Show full text]