W&E to Auveco Cross Reference
Total Page:16
File Type:pdf, Size:1020Kb
Load more
Recommended publications
-
Product Overview
Alcoa Fastening Systems Product Overview Threaded Bolts Threaded Pins Collars Nuts Screws Lockbolts & Collars Blind Bolts Blind Rivets Panel Fasteners Inserts & Studs Latches & Mechanisms Fluid Fittings Alcoa Fastening Systems Product Overview Special Sandwiched Structure Fasteners Threaded Bolts 12-POINT HEAD HEX HEAD FLUSH HEAD/RECESS DRIVE 3 The 12-Point Head Threaded Bolt • 12-Point (or Double Hex) Head Bolts – Designed to be used for high load tensile applications. The 12-point head allows the bolt to be torqued at high values to the desired joint preload, without damage to the head. Manufactured from high strength material to provide minimum tensile strength values of 160KSI, 180KSI, and 220KSI. – Sample parts: – Sample parts: • MS9750 (Double Hex/Extended Washer) • BACB30MR (12-Point/Extended Washer) • MS9759 (Double Hex/Extended Washer) • BACB30PN (12-Point/Extended Washer) • MS14163 (Spline Drive) • BACB30US (12-Point/Extended Washer) • MS14181 (Spline Drive) • BACB30UU (12-Point/No Washer) • MS21134 (Spline Drive) • MS21250 (12-Point/Extended Washer) 4 The Hex Head Threaded Bolt • Hex Head Bolts – Designed for general purpose applications. Manufactured from high strength material to provide a minimum tensile strength value of 160KSI. – Sample parts: – Sample parts: • NAS673 – NAS678 • BACB30LJ • NAS6203 – NAS6220 • BACB30LM • NAS6303 – NAS6320 • BACB30NM • NAS6403 – NAS6420 • BACB30NR • NAS6603 – NAS6620 • NAS6703 – NAS6720 • NAS6803 – NAS6820 5 The Flush Head/Recess Drive Threaded Bolt • Flush Head/Recess Drive Bolts – Designed -
Und Die Verbindung Stimmt
▪ Zollschrauben ▪ Schnellverschlüsse ▪ Luftfahrt-Normteile ▪ Spannverschlüsse ▪ MS-NAS-AN Hardware ▪ Gewindeeinsätze GmbH ... und die Verbindung stimmt MS-NAS-AN HARDWARE - LUFTFAHRTNORMTEILE 002 INHALTSVERZEICHNIS INDEX AN-MS-NAS HARDWARE 003 ESNA WRENCHABLE NUTS ���������������������������������������������������������������������004 ESNA Anchor NUTS ���������������������������������������������������������������������������������012 National Aerospace Standard ���������������������������������������������������������������018 Air Force/Navy Aeronautical �����������������������������������������������������������������059 Military Standard Retaining Rings & Lockwasher �����������������������������076 Military Standard Begriffe & Definitionen ������������������������������������������077 Military Standard Materialien ���������������������������������������������������������������078 Military Standard �������������������������������������������������������������������������������������080 AN-MS-NAS HARDWARE 003 ESNA WRENCHABLE NUTS 004 ESNA WRENCHABLE NUTS ESNA WRENCHABLE NUTS LH7644 HEX, THIN, STRUCTURAL, SHEAR 1/2-20 thru 1 1/2-12 to 450°F. LH12284 HEX, LOW HEIGHT STRUCTURAL, SHEAR, 80.000 PSI 1/2-20 thru 1 1/4-12 to 450°F. NAS1757 1801 HEX, FULL HEIGHT 4-40 thru 3/4-16 to 450°F. AN363, MS20365, MS21045, NAS1021 1802 HEX, HIGH TEMPERATURE 8-32 thru 1/2-20 to 1200°F. MS20500 1803, SM1813 HEX, FULL HEIGHT 4-40 thru 5/8-18 to 450°F and 800°F. AN363, MS20365, MS21045, MS21046, NAS1021 Z1200 HEX, HIGH TEMPERATURE 00 thru 00 to 1200°F. ESNA WRENCHABLE NUTS 005 ESNA WRENCHABLE NUTS NE4717 HEX, THIN, CASTELLATED, SELF-LOCKING 10-32 thru 1-12 to 250°F. MS17826 NE4753 HEX, FULL, CASTELLATED, SELF-LOCKING 10-32 thru 1-12 to 250°F. MS17825 NE8235 HEX, CASTELLATED, C‘BORED, SELF-LOCKING, CAPTIVE WASHER 10-32 thru 1-12 to 250°F. MS21224 NE9106 HEX, CASTELLATED, C‘BORED, SELF-LOCKING, STEEL, CAPTIVE WASHER 10-32 thru 5/8-18 to 250°F. E9868 REDUCED HEX, FULL, LIGHTWEIGHT, CASTELLATED, SELF-LOCKING 10-32 thru 1-12 to 450°F. -
Includes the New 2015 AB Clip Assortment! © 2013 Wurth USA, Inc
WURTH USA ASSORTMENTS Includes the new 2015 AB Clip Assortment! Revision 06/2015 - Assortment Book_Art. #1STA30797 © 2013 Wurth USA, Inc. ASSORTMENTS Revision 06/2015 - Assortment Book_Art. #1STA30797 © 2013 Wurth USA, Inc. ASSORTMENT INDEX Description Art. # Page Description Art. # Page 8.8 Hex Bolt (Zinc Plated) - Metric 196400004 17 Fuses - Max/Mini Blade 196417312 61 196460201 - Fuses - Mini Blade 196417311 61 A/B Clip Assortment 4 - 9 196460212 Fuses - Regular Blade 196417310 60 AC Orifice Tube 1964176474 65 Grade 5 SAE Zinc Hardware 19651071 86 Aluminum Sealing Ring 19640463 24 Grade 5 USS Zinc Hardware 19651072 87 Battery Terminal w/ Solder Slugs & Heat Shrink 196405572 59 Grade 8 SAE Yellow Hardware 19651075 85 Battery Terminal w/ Solder Slugs & Heat Shrink 19641510 59 Grade 8 USS Yellow Hardware 19651076 84 Black Tie Strap 196415021 63 Grade 8.8 European Yellow Metric Starter 196500570 82 Black Tie Strap - Assorted w/Rack 196415022 63 Grade 8.8 European Zinc Metric Hardware 19650057 81 Brass Air Brake Fitting 196488401 72 Grade 8.8 ISO (Japanese) Zinc Metric Hardware 19650060 83 Brass Fitting 196488402 73 Grease Fitting - Metric 19640986 73 Brass Push to Connect D.O.T. Air Brake Fittings 196488501 72 Grease Fitting Metric & Standard 19640986 75 Bulb - Domestic & Japanese 19641721 56 Hardware (Zinc Plated) - Metric 19640057 11 Bulb - Duratek Master 196417201 58 Hex Bolt - EURO/SO Metric 196400005 13 Bulb - European 19641720 57 Hex Nut - Metric 19640317 20 Copper Sealing Ring 19640460 24 Hex Nut USS/SAE Zinc 1964033031 41 Cotter -
Body Shop Fasteners
BSF-712 QUALITY BODY PRODUCTS SHOP FASTENERS QUALITY PRODUCTS PRODUIT DE QUALITE INTERIOR EXTERIOR INTERIEUR EXTERIEUR ATTACHES A CARROSSERIE H. Paulin & Co., a division of The Hillman Group Canada ULC Toronto, Canada M1L 4N3 www.hpaulin.com www.hpaulin.com INDEX Name Page Name Page BOLTS GM........................................................................ 30-32 Misc. Bolts ................................................................. 20 Interior Retainers. Imported Brands Body Bolts (Inch & Metric).................................... 17-20 BMW..................................................................... 34 Bumper Bar Bolts (Inch & Metric)....................... 15-17 Honda.................................................................. 34-35 Hyundai.............................................................. 36 KIA........................................................................ 36 Lexus.................................................................... 36 BUSHINGS Mazda.................................................................. 36-37 Door Hinge Bushings............................................. 75 Mersedes-Benz................................................. 37 Mitsubishi.......................................................... 37 CLIPS Nissan.................................................................. 38 ‘T’ Bolt Clis (Inch)...................................................... 21 Toyota.................................................................. 39 Moulding Clips & Retainers................................. -
Body Shop Fasteners Attaches À Carrosserie
AN INTRODUCTION TO... BODYBODY SHOPSHOP FASTENERSFASTENERS AATTTTACHESACHES ÀÀ CARROSSERIECARROSSERIE …UNE INTRODUCTION. For a full listing of Papco® Body Shop Fasteners, please refer to our current catalogue or visit our website to download a PDF version. SPEED CLIPS & NUTS BUMPER BAR BOLTS WEATHERSTRIP FASTENERS ‘PALNUTS’ ‘CONELOK’ LOCKNUTS ANCHOR NUTS & CLIPS RETAINERS LICENCE PLATE BOLTS PLUG BUTTONS ‘PUSHNUT’ METRIC MOULDING BOLTS & CLIPS SHIMS FASTENERS RIVETS HINGE PINS & BUSHINGS ‘U’ NUTS (MULTI & SINGLE THREADS) GLASS SHOP FASTENERS BLIND WELL NUTS BODY BOLTS TRIM FASTENERS SERT-A-NUTS FLAT TYPE SPEED NUTS ÉCROUS TENIR TYPE FRAISÉE 240 Series Used with machine screws and sheet metal screws. One piece, heat treated spring steel self-locking fastener. The original equipment fastener used on headlights, radiators, moulding, trim, gravel deflectors, ornaments, emblems, name plates, etc. FLAT TYPE ORDER BY STOCK NUMBER Standard Package: Contains 100 Pieces 240-089 240-091 240-120 240-108 240-100 240-101 240-159 240-127 ILLUSTRATIONS ARE APPROXIMATE Dimensions Stock No. Screw Size Other No. Application A x B x T 240-089 6-32 1/2 x 5/16 x .017 2089 General Purpose. 240-091 6-32 7/8 x 1/2 x .017 1898 Chrysler products garnish moulding ornament. 240-100 8-32 1/2 x 5/16 x .017 2091 General Purpose. 240-101 8-32 7/8 x 1/2 x .017 1899 Chrysler products radiator and trunk medallion. 240-120 10-24 3/4 x 7/16 x .022 2092 General Purpose. 240-159 1/4-20 1 x 9/16 x .027 1903 General Purpose. -
HARDWARE AIRCRAFT WASHERS Are Easily Recognized
HARDWARE AIRCRAFT WASHERS are easily recognized. They are those thin looking and capable of withstanding high tension loads. The standard washer is 1/16 inch thick and is avail - nuts, and they are used most often with clevis bolts. Be careful when using a castle nut on a clevis bolt able in two types for each of the most commonly Never use shear nuts where the installation is sub - in the control system where rudder pedals or other used bolt diameters. The smaller diameter washer jected to tension loading. linkage might interfere with other parts. Cotter pins is known as the AN960, and the larger diameter SELF-LOCKING NUTS & have a way of snagging. washer, the AN970. The larger washer is often NUT SAFETY FEATURES TORQUING called a wood washer because it is used most fre - All nuts/bolt installations in your aircraft should have Except as a last resort, do not torque a bolt by turn - quently against wood surfaces to provide a larger some safety features to prevent their loosening in ing it. bearing surface. service. Methods employed include the self-locking Tighten or torque castellated nuts as you would any Plain washers are used in bolt installations to pres - nuts, cotter-key combinations, jam nuts, lock wash - other standard nut. If the slots and cotter pin hole in ent a smooth level bearing surface for either the bolt ers, palnuts, and still found in primitive areas, peen - the bolt will not line up for safetying, tighten the nut head or nut - sometimes both. Use a washer under ing of the bolt end with a hammer. -
2019 PRODUCT CATALOG at S&R Fastener Company, Our Objective Is to Provide Our Customers with the Highest Quality Products and Services at the Fairest Prices
AUTOMOTIVE CLIPS SAFETY ITEMS CABINETS FASTENERS CAR DETAILING FUSES ABRASIVES TIRE REPAIR RIVETS DRAIN PLUGS/GASKETS WHEEL WEIGHTS TAPES DRILL BITS MINIATURE LAMPS AIR HOSE ELECTRICAL ITEMS BUMPER BOLTS AND SO MUCH MORE ! 2019 PRODUCT CATALOG At S&R Fastener Company, our objective is to provide our customers with the highest quality products and services at the fairest prices. This is backed by a professional sales force and professional office, warehouse, manufacturing and research/development staffs, which when combined, result in an unbeatable team to serve our customers needs. Let us know how we can help you. S & R Fastener Co., Inc. P.O. Box 849 San Antonio, FL 33576 Toll Free Phone: 877-773-2276 Toll Free Fax: 866-299-3563 Visit us online at: www.srfast.com S & R Fasteners reserves the right not to be responsible for the topicality, correctness, completeness or quality of the information provid- ed and reserves the right to change or correct information in this catalog without prior announcement. For the most updated information or to place an order online, please go to www.SRFast.com Also available from S & R Fastener Co., Inc.! International Epoxies and Sealers! A U.S. Manufacturer of Adhesives, Sealants, Foams, Coatings and Specialty Products. Seam Sealers Plastic Repair Panel Bonders Automotive Foams Coatings Attachment Tapes Service Aids Primers www.useies.com ALPHABETICAL INDEX A D AC Parts ............................................. 7 Detail Supplies.................................... 42 Abrasives ............................................ 38 Disinfectant Spray .............................. 15-4 Absorbent Pads ..................................15-5, 41-6 Door Hinge Pins, Bushing, Kits .......... 12 Acura/Honda Fastener Section .......... 22 Drain Plugs/Gaskets ...........................5 Acid Brushes ..................................... -
Fasteners First Loosen Without Turning!
"Settling down" is the term ESNA labora- FASTENERS tory people use to describe a relaxation phenomenon that occurs at room tem- perature under static conditions. During the first few hours after a nut and bolt FIRST LOOSEN are tightened on an arbor, the fastener system has lost some of its pre-stress. WITHOUT TURNING! The mechanical fits and finishes involved determine to a great extent how much initial clamping load will be lost. With precise, well-finished parts, this relaxa- tion may be limited to 2 or 3 per cent of pre-stress. With rough surfaces, loose thread tolerances and lack of squareness, Schematic of all-metal fastener testing histories shows how bolt tension is lost first in the static condition and then, more rapidly, after vibration begins. The nut turns at a critical tension level. INITIAL BEST AIRCRAFT -QUALITY FASTENERS POOREST COMMERCIAL - QUALITY FASTENERS NUT DOES NOT TURN CRITICAL F _J 0 w NUT ROTATES O FAILURE RANGE STATIC VIBRATION TESTING 13 Aircraft Technical Book Company http://www.ACTechbooks.com (800) 780-4115 (970) 887-2207 as much as 10 per cent of the original twisted during tightening. loading may be lost. When a retightened fastener system is This stress relaxation is analogous to subjected to a vibration test, loss of high-temperature creep. We suppose that clamping force continues, but at a rate it involves a gradual adjustment as local- much slower than occurred initially. The ized zones stressed beyond the yield point nut does not turn on the bolt while that transfer load to adjacent metal. Another is happening. -
BAC to MIL-SPEC Cross Reference | Military Fasteners
BAC to MIL-SPEC Cross Reference Military-Fasteners.com BAC Part A-Z MIL-SPEC Part Item Name View & Buy Online BAC-J40A-10-4 MS25083-2AA4 Bonding Jumper MS25083-2AA4 BAC-J40A-20-12 MS25083-2BB12 Bonding Jumper MS25083-2BB12 BAC-J40A-20-6 MS25083-2BB6 Bonding Jumper MS25083-2BB6 BAC-J40A-21-3 MS25083-2BC3 Electrical Lead MS25083-2BC3 BAC-J40A-21-5 MS25083-2BC5 Electrical Lead MS25083-2BC5 BAC-J40A-30-6 MS25083-2CC6 Electrical Lead MS25083-2CC6 BAC-R16A-14 NAS1329A06K120 Blind Rivet Plain Nut NAS1329A06K120 BAC415BB5AD14 MS20470AD5-14 Solid Rivet MS20470AD5-14 BACB10A692 MS27640-8 Airframe Ball Bearing MS27640-8 BACB15DN3AD9 MS20470AD3-9 Solid Rivet MS20470AD3-9 BACB30CC5W10 NAS1669-08L10 Blind Rivet NAS1669-08L10 BACB30CC5W3 NAS1669-08L3 Blind Rivet NAS1669-08L3 BACB30CC5W6 NAS1669-08L6 Blind Rivet NAS1669-08L6 BACB30CC6W6 NAS1669-3L6 Blind Rivet NAS1669-3L6 BACB30CC6W9 NAS1669-3L9 Blind Rivet NAS1669-3L9 BACB30CC8W3 NAS1669-4L3 Blind Rivet NAS1669-4L3 BACB30FD4-10 NAS624H10 Shear Bolt NAS624H10 BACB30FD4-8 NAS624H8 Shear Bolt NAS624H8 BACB30GF5-6 NAS1750-08L6 Blind Rivet NAS1750-08L6 BACB30GF6-3 NAS1750-3L3 Blind Rivet NAS1750-3L3 BACB30GN6-22 NAS6606-22 Shear Bolt NAS6606-22 BACB30LB6-9 MS90354U0609 Blind Rivet MS90354U0609 BACB30LJ4U5 NAS6204-27D Shear Bolt NAS6204-27D BACB30LM3-3 NAS6703-3 Shear Bolt NAS6703-3 BACB30LM3U30 NAS6703U3 Shear Bolt NAS6703U3 BAC Part A-Z MIL-SPEC Part Item Name View & Buy Online BACB30LR4-6 MS24694S101 Machine Screw MS24694S101 BACB30MT5-10 NAS625-10 Shear Bolt NAS625-10 BACB30N6-7 NAS1446-07 Pin-rivet NAS1446-07 -
Table of Contents
Table of Contents 10000 Hood Insulation Clips 1 90400 Hood Prop Rod Clips 123 10100 Clips and Retaining Clips 4 100000 Window Guides 125 10200 Push-Type Clips 16 110100 Metric Free Spinning Washer Nuts, Hex 126 Flange Nuts & Flange Lock Nut 10300 Import Nylon Clips 27 110200 Metric Extruded "U" Nuts 128 10400 Honda/Acura Specific Clips 34 110300 Metric Thread Body Bolts 130 10500 Toyota/Lexus Specific Clips 39 120000 Metric Thread Cap Screws, Hex Nuts & 133 Washers 10600 Nissan/Infiniti/Mazada Specific Clips 46 130000 J.I.S. Hex Flange Bolts 137 10700 Hyundai/Kia Specific Clips 51 140000 Bumper Bolts, Flange Lock Nut & Free 139 Spinning Washer Nut 10800 BMW/Mercedes Specifc Clips 53 140300 Shims 140 10900 VW/Audi/Volvo/Subaru Specific Clips 57 150000 Standard Thread Body Bolts, Extruded "U" 141 Nuts & Spin Lock Nuts 20100 Nylon Nuts & Screew Grommets 62 160000 U.S.S. Cap Screws, Hex Nuts & Washers 143 20300 Import Nylon Nuts & Screw Grommets 67 200000 Fuses 147 30100 "U" Nuts, Flat Nuts, Tubular Nuts, Thread 79 210000 Harness Connectors & Socket Assemblies 150 Cutting Nuts, Bolt Clips & Misc. Fasteners 30200 Jack Nuts®, Nutserts®, Speciality Inserts & 86 220000 Connectors 153 Screws 30300 Well Nuts® & Speciality Screws 88 230000 Cotter Pins 154 40000 Tapping Screws & License Plate Screws 89 240000 "O" Rings 155 50000 Hex Head & Torx® Head Tapping Screws 95 250000 Sheet Metal Plugs 158 60100 Nylon Rivets 99 260000 Oil Drain Plug 159 60200 Metal Rivets 101 270000 Moulding Clips & Fastners 160 70000 Headlight Adjusting Screw Assemblies 110