HUSKY GLASS

FITTING INSTRUCTIONS - NOTICE DE POSE - MONTAGE HANDLEIDING - MONTAGEANLEITUNG ISTRUZIONI DI MONTAGGIO - INSTUCCIONES DE MONTAJE

Tools Required

Posidrive screwdriver Allen key 5mm

Tape measure

Torque wrench and 6mm bit Spanner 13mm Spirit Level

Contents of Kit

M8 Nut x 2

Wheel carriage x 2 Clip stop x 2 Strap bolt x 2

Glass clamp x 2 (Type dependent upon weight capacity)

Height adjustment Lock plate x 2 Floor guide x 1 plate x 2

1 Fitting clamps (c) 2 Assemble hanger components

Wheel carriage Gaskets

(a) Unscrew to loosen clamp M8 Nut Glass

Height 30Nm adjustment (d) 50 plate

Locking plate

(b) Clean glass (c) Set clamp to glass Strap bolt (d) Finger tighten ALL screws Torque outer then inner screws 3 Hang glass door

(a) Insert hanger assembly (b) Insert clip stop (c) Check orientation of hanger assembly in the track (d) Slide hanger assembly into (a) (a) the clamp (e) Final locate - hang glass panel

IMPORTANT (b) (b) Please note orientation of hanger assembly

(c) Direction of (c) hanger assembly

(d) (d)

Glass clamps

(d) Slide hanger assembly into the clamp channel (e) Allow glass panel to hang by locating the tabs on the lock plate into the cut-outs in the clamp

Lock plate

Location tabs Height adjustment plate

4 Height adjustment - Adjust strap bolt to set door height

Height adjustment plate

Strap bolt

Ensure glass panel is level - hangers evenly adjusted NB - minimum/maximum adjustment possible is shown in diagram 7 5 Set door height

Once height is set - lock hangers into position by pushing the locking plates in the direction of the arrows

Locking plate Locking plate

6 Set Floor Guide (a) Set floor guide for glass door thickness, 8, 10 or12 mm (b) Position floor guide (a) (c) Check level of panel with spirit level (d) Mark position of guide (e) Check proposed travel of door (when fully open the door is still in the guide) (f) Re-position glass door (g) Secure guide with screws (h) Slide panel back into floor guide (i) Secure retaining clip stop (i)

Tighten screws

Ensure correct tension adjustment

SOFT FIRM

(c)

(e)(f)(g)(h)

(d) (b) 7

Fixed Panel Soffit fix Wall fix for 10mm glass only 5mm Spacer not by PCH Clip stop 601H Hanger 284 Fascia F136

22

35 35 35 10-20 10-20 10-20 136 136 41 86-96 136 41 86-96 41 86-96 41 51-61 65 1 1 1 50

F136 F136 F136 Glass clamp ) ) ) ) H H H H S O O O T ( ( ( ( 3 t t t t 1 1 1 2 5 h h h h 0 0 0 1 g g g g 2 1 1 1 i i i i - - e e e e - - - H H H H H H H H H t g g g S O e n n n O O O i i i T S n n n k e e e c p p p a r O O O T

Guide Guide Guide Guide 8-12/SN 8-12/SN 8-12/SN 8-12/SN

10 10 10 94X 5mm Spacer 50 24 Channel not by PCH

Fixed panel height = Opening height (OH) -25 Sliding panel height = TSH -123 Sliding panel height = Opening height (OH) -101

REFER TO HUSKY INSTRUCTIONS FOR GENERAL TRACK INSTALLATION DETAILS

(All dimensions in mm)

P C Henderson Limited, Durham Road, Bowburn, County Durham DH6 5NG, UK. Web: www.pchenderson.com UK Customer Services Department: Tel: +44 (0)191 377 7345 Fax: +44 (0)191 377 3116 Email: [email protected] Part No: 668102 Export Department: Tel: +44 (0)191 377 7346 Fax: +44 (0)191 377 0755. Email: [email protected]. September 2012 - Issue 2 For all technical queries email our Technical Department: [email protected]