(SEM/EDS) Methods for the Analysis of Small Particles Adherin
Total Page:16
File Type:pdf, Size:1020Kb
![(SEM/EDS) Methods for the Analysis of Small Particles Adherin](http://data.docslib.org/img/82319743cc8cfba038413a2c1c763521-1.webp)
The author(s) shown below used Federal funds provided by the U.S. Department of Justice and prepared the following final report:
Document Title: Use of Scanning Electron Microscopy/Energy Dispersive Spectroscopy (SEM/EDS) Methods for the Analysis of Small Particles Adhering to Carpet Fiber Surfaces as a Means to Test Associations of Trace Evidence in a Way that is Independent of Manufactured Characteristics
Author: David A. Stoney, Ph.D., Paul L. Stoney, MBA
Document No.: 239051
Date Received: July 2012
Award Number: 2010-DN-BX-K244
This report has not been published by the U.S. Department of Justice. To provide better customer service, NCJRS has made this Federally- funded grant final report available electronically in addition to traditional paper copies.
Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S.
Department of Justice.
Use of Scanning Electron Microscopy / Energy Dispersive Spectroscopy (SEM/EDS) Methods for the Analysis of Small Particles Adhering to Carpet Fiber Surfaces as a Means to Test Associations of Trace Evidence in a Way that is Independent of Manufactured Characteristics
Award 2010-DN-BX-K244
David A. Stoney, Ph.D. and Paul L. Stoney, MBA Stoney Forensic, Inc. 14101-G Willard Road Chantilly, VA 20151
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Abstract
Very small particles (VSP) are ubiquitous in our environment and are virtually ignored by forensic science. These particles range in size from an order of magnitude smaller than conventional trace evidence, down to the molecular level (now routinely exploited through DNA analysis). We move about in a soup that is a combination of VSP that provides an extraordinary, largely untapped resource for forensic associations and source attribution. This project was an initial, highly successful effort to exploit VSP for one specific application.
An innovative instrumental trace evidence analysis approach was developed and tested for the recovery and quantitative SEM/EDS analysis of VSP adhering to the surfaces of carpet fibers – one of the most common types of trace evidence examined in crime laboratories.
Program goals were: (1) to develop methods to quantitatively remove VSP from carpet fibers and prepare them for SEM/EDS analysis, and (2) to exploit existing computer-assisted SEM/EDS methods to test whether the resulting VSP profiles are useful to quantitatively associate shed fibers with a source carpet. Specific program objectives were to: − Develop suitable methods as described − Use these methods to determine VSP profiles within source carpets − Analyze VSP adhering to single fibers from the source carpets, and determine if their VSP profiles were consistent with an unbiased statistical sampling from the source carpet − Explore between-item variation for VSP profiles using a broader qualitative survey of carpets
Appropriate methods were developed and used to assess within-carpet variability using VSP from three different areas on each of nine carpets. Carpet area VSP profiles were defined by a set of ten carpet fibers and the profiles of individual fibers from these areas were compared. Between-item variation was explored using a survey of VSP profiles on an additional 12 carpets.
Program goals and objectives were met. The regular occurrence of hundreds to thousands of VSP on individual carpet fibers was demonstrated. The quantity and character of VSP was sufficient to associate fibers with their carpet area of origin. The hypothesis of a strictly quantitative relationship among VSP, as measured using environmental particle profiles, was strongly rejected. These environmental particle profiles were found to be unsuitable to assess VSP variability. An alternative method was developed based on Target Particle Types (TPTs) defined by their elemental profiles as measured by computer-assisted SEM/EDS. Within-carpet and between-carpet variations showed a roughly even distribution for most TPTs and between-carpet variations showed a wide range in types and quantities of VSP.
The usefulness of VSP to link of carpet fiber evidence has been established. There is now a clearly achievable potential to use VSP for independent, quantitative testing of the common origin of carpet fibers. To unlock this potential, a set of follow-on research steps have been outlined and are ready to be undertaken.
The specific application of VSP to carpet fibers is ready for development, but the proof of principle resulting from this research is of much broader significance for the future of trace
Page 2 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association evidence analysis. It is a breakthrough providing the impetus and direction for a fundamental change in the way that forensic trace evidence is conceptualized, analyzed and used in the criminal justice system. The results of this research are likely extendable, with minor modifications, to other trace evidence types, and are expected to contribute significantly for those types of trace evidence that have long been considered of low evidential value. Furthermore, entirely new approaches to trace evidence are enabled by exploiting VSP profiles, such as comparing different types of trace evidence with one another and comparing VSP defined by crime scene or suspect environments to that on virtually any item of physical evidence.
Page 3 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table of Contents
Abstract 2 Table of Contents 4 Executive Summary 5 I. Introduction 13 II. Methods A. Carpet Sample Selection 16 B. Sampling of Fibers from Carpets 17 C. SEM Imaging and Qualitative Assessment of Particle Abundance on Fiber Surfaces 20 D. Isolation of Particles from Fibers (Protocol Development) 20 E. Isolation of Particles from Fibers (Finalized Method) 21 F. Computer-Assisted SEM/EDS Analysis of Particles 22 G. Analysis of Environmental Particle Groupings 24 H. Within-Sample Elemental Profile Classes 25 I. Selection, Definition and Frequency of Target Particle Types 25 III. Results A. Isolation of Particles from Fibers 26 B. Computer-Assisted SEM/EDS Analyses 27 C. Statistical Testing of Environmental Particle Groupings 33 D. Elemental Profile Groupings and Classes 33 E. Definition of Target Particle Types 33 F. Occurrence of Target Particle Types for Carpets, Carpet Fibers and Process Blanks 37 G. Variation Among Different Areas of the Same Carpet 42 H. Variation Within Single Carpet Areas 49 I. Variation Among Different Carpets 56 IV. Conclusions A. Discussion of Findings 59 B. Discussion of the Underlying Technology and Scope 66 C. Implications for Policy and Practice 67 D. Implications for Further Research 69 V. References 73 VI. Dissemination of Research Findings 76
Page 4 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Executive Summary
Our research has demonstrated that hundreds to thousands of very small particles (VSP) cling to the surfaces of individual carpet fibers. We have developed methods to remove these particles, analyze them, and use them to link the fibers to the carpet from which they came.
This project focused on one specific trace evidence application (carpet fibers) and one specific instrumental particle analysis method (computer-assisted SEM/EDS) to explore and test a fundamentally different approach to trace evidence analysis. In doing so, a set of reasonable assumptions and choices were made that can themselves be tested and refined for this specific application.
As proof of principle our findings are a highly significant breakthrough for the future of trace evidence analysis. They demonstrate a way to remove fundamental limitations of class associations and provide the impetus and direction for fundamental change in the way forensic trace evidence is conceptualized, analyzed and used in the criminal justice system. Further research is encouraged to allow the independent, quantitative testing of common origin using populations of VSP.
Problem and Purpose There is a fundamental limitation to the probative value of many of the most common types of trace evidence (e.g., fibers, glass, paint) because their characteristics are determined by their manufacture. As mass-produced commodities, probative value is limited to class associations. Multiple-transfer cases shatter this limitation. These are cases where a set of different trace evidence materials, found on a suspect, correspond to sources at a crime scene, and/or the reverse: where a set of trace evidence materials, found at the crime scene, correspond to suspect- related sources. The well-known case of Atlanta child murders provides an excellent example, where fibers corresponding to the trunk of Wayne Williams’ car, his bedroom carpet, his bedspread, and his blanket were all found together on multiple victims. When the possibilities of correlation can be discounted, the probative value can become extraordinarily high, even when probabilities for the occurrence of individual trace evidence types are modest, or subject to inherent imprecision in their estimates. The co-occurrence of multiple events of modest frequency is the foundation for all highly probative types of physical evidence, including DNA and fingerprint identifications. The potential is also there for trace evidence.
This research is part of an effort to radically improve trace-evidence analysis, systematically addressing the fundamental limitations affecting the strength and measurement of probative value, by exploiting the very small particles (VSP) that are present on virtually every material or object. These VSP “ride piggy-back” on conventional trace evidence. They occur in complex mixtures and include a tremendous variety of particles that are acquired when manufactured materials are exposed to alternative environments. These particles reflect cumulative exposures and conditions; they will be highly characteristic of the local environment and their presence, identity and relative quantities, provide an untapped source of individuality for conventional trace evidence.
Page 5 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
There is a tremendous potential here: every trace evidence case becomes a multiple-transfer case, with the adhering fine particles providing an independent quantitative means to test hypotheses of common origin. Consider: if these carpet fibers came from that carpet, then the multivariate occurrence of a quantitative profile of VSP, present on that carpet, ought to be present, subject to statistical sampling, on these fibers.
To unlock this potential, research is required that (1) determines which VSP have useful forensic performance characteristics, (2) develops suitable methods for detection and measurement, and (3) provides data on variation and occurrence that enable reliable statistical interpretation.
The research described in this report develops and tests this approach using the elemental analysis of populations of VSP occurring on the surface of carpet fibers. Carpets are common in indoor domestic and many commercial environments, and they are ubiquitous in automobiles. Carpet fibers are easily shed, easily transferred, easily recognized on careful examination, and easily recovered. Carpet fibers are a particularly suitable candidate for this approach: they are subject to long-term exposures, they have a tremendously large exposed surface area, and they are designed to trap small particles.
Methods for computer-assisted SEM/EDS analysis of particles in the size range of interest have been intensively developed in the past ten years for workplace and environmental monitoring. In crime laboratories, the methods have been in use since the 1980s for identification of gunshot residue particles (GSR), based on a combination of their elemental composition and morphology.
For initial investigations we used existing computer-assisted particle analysis protocols and classification criteria designed for environmental applications, as the methods are rigorously standardized and the particle classification criteria are explicitly defined. Methods for removal of particles from fibers and their transfer to SEM stubs needed to be developed.
The goals of the present research were to (1) to develop the methods needed to quantitatively remove VSP from carpet fibers and prepare them for SEM/EDS analysis, and (2) to exploit existing computer-assisted SEM/EDS methods to test whether the resulting fine particle profiles are useful to quantitatively associate shed fibers with a source carpet.
Our specific hypothesis was that carpet fibers from a source carpet will bear a measurable VSP profile that is a function of an unbiased statistical sampling of the VSP population present on the source carpet. To test this hypothesis and put the results in context, we defined four objectives: (1) Develop methods, compatible with existing fiber analysis protocols, and using currently available crime laboratory resources, to quantitatively remove and analyze the VSP adhering to carpet fibers. (2) Use these methods to determine within-item variation (VSP profiles within the source carpet). (3) Analyze VSP adhering to fibers that have been shed from the source carpets, and determine if the profiles occurring on these fibers are consistent with an unbiased statistical sampling from the source carpet population. (4) Conduct a broader qualitative survey of carpet VSP profiles to explore between-item variation.
Page 6 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Research Design Carpets were selected from residences, vehicles and workplaces with an emphasis on those occurring most commonly in forensic casework: nylon and polyester fibers with trilobal or circular cross sections. Twenty-one carpets were selected and sampled. These carpets were not meant to be representative of a population, but to cover a range of settings so that a range of within- and between-carpet variation could be studied.
Fibers were cut directly from looped piles in the carpets. Carpets used for analysis of within-item variation (nine of the 21) were sampled from three areas, spaced from one to three feet apart.
A method to recover VSP from carpet fibers was developed after testing five alternative washing liquids and ten alternative methods of agitation. Completeness of particle removal was assessed by SEM imaging of fibers. The finalized method used pre-filtered reagent grade ethanol with sonication in a micro-centrifuge tube for ten minutes. This was followed by filtration to recover the particles, drying and mounting for computer-assisted SEM analysis. Process blanks were included alongside each batch of samples processed (pre-filtered ethanol sonicated for ten minutes in an empty tube and otherwise treated in an identical manner).
Standardized computer-assisted SEM/EDS analyses were performed by Gateway Analytical, LLC. Analyses were conducted on a total of 120 samples, along with 12 process blanks. Twenty- seven samples were sets of ten fibers from the nine carpets used to study within-carpet variation (one set from each area sampled). The 10-fiber sets were used to represent the population of VSP at that area of the carpet. Eighty-one individual fibers, three from each of the 27 areas, were used to represent individual shed fibers from these areas. Twelve additional carpets were sampled (ten fibers from each) and were used to represent populations of particles for those carpets.
The computer-assisted SEM/EDS analysis was performed on an Aspex Corporation PSEM Explorer SEM-EDS system using the Automated Feature Analysis (AFA) program within the Aspex Corporation Perception software. We adopted an existing methodology with a mix of rarely encountered and commonly occurring elements among a set of 28. The number of elements (among those detectable by EDS) is not restricted by the SEM/EDS or by the software and the assortment of elements can be changed. The number of elements selected affects the overlap of x-ray lines, but ambiguities are resolved by the x-ray detection software using known correlated x-ray emissions for the specific elements. The specific operational settings of the software restricted detection to 4000 particles and 28 elements: Sodium (Na), Magnesium (Mg), Aluminum (Al), Silicon (Si), Sulfur (S), Chlorine (Cl), Calcium (Ca), Titanium (Ti), Chromium (Cr), Manganese (Mn), Iron (Fe), Nickel (Ni), Copper (Cu), Zinc (Zn), Bromine (Br), Strontium (Sr), Zirconium (Zr), Silver (Ag), Tin (Sn), Antimony (Sb), Barium (Ba), Tungsten (W), Gold (Au) and Mercury (Hg).
Environmental Particle Groups were determined following pre-defined classification rules based on percentages of total x-ray counts for specified elements. Ten alternative criteria were applied in sequence until a criterion was met. The specific criteria specified up to four elements. Most were based on the presence of one or two elements; with x-ray count thresholds as low as 10%. Frequencies of Environmental Particle Groups were determined for each of the 120 sample
Page 7 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
analyses and 12 sample process blanks. Within-item variation was assessed using maximum- likelihood estimation and chi-square testing.
As an alternative to Environmental Particle Groups, Target Particle Types (TPTs) were defined based on frequently occurring elemental profiles (> 1%) in the 27 10-fiber sets used to study within-carpet variation. A set of 68 mutually-exclusive TPTs were defined after grouping of closely related and overlapping elemental profile classes. Frequencies of each of the TPTs were then determined for each of the 120 sample analyses and 12 sample process blanks. Within- and between-item variation was assessed by analysis and comparison of the TPTs, including the presence or absence of TPTs and their relative abundance in samples (proportionality and rank).
Findings and Conclusions
All of the findings in this project are based on the analysis of carpets covering a limited range of characteristics (primarily trilobal, nylon fibers) and present in a limited set of environments. Accordingly, the conclusions made from these findings would apply only to these types of carpets. They serve as a model and as an initial study. As with any research, the initial efforts define a starting point. Further work on other carpet types can then be considered in reference to these data and the findings can then be either generalized or more definitively qualified.
There were nine specific findings:
1. Very small particles (VSP) present on the surfaces of individual carpet fibers can be recovered nearly completely and prepared for computer-assisted SEM/EDS analysis by extraction with reagent ethanol and filtration onto polycarbonate filters.
The method is effective, employs non-toxic materials, and is easy to apply. Practitioner review of the method established that it could be easily incorporated as a preliminary washing step prior to polarized light microscopy. With the development of this method, the first of the project objectives was achieved: to develop methods, compatible with existing fiber analysis protocols, and using currently available crime laboratory resources, to quantitatively remove and analyze the VSP adhering to carpet fibers.
2. Hundreds to thousands of VSP routinely occur on the surface of individual carpet fibers.
VSP isolated from individual fibers and analyzed by computer-assisted SEM/EDS varied in number from less than a hundred to greater than 4000 (the maximum number examined). After allowing for particles occurring in process blanks, there is an average (n = 81) of over 500 ethanol-insoluble VSP on the surface of a single carpet fiber. The confirmed presence of VSP in this quantity on carpet fibers enables research on the best means to analyze and interpret them, unlocking their extraordinary potential to enhance probative value and independently test hypotheses of common origin.
Page 8 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
3. VSP on individual carpet fibers, when classified using criteria developed for environmental applications, cannot be considered as an unbiased statistical sampling of a VSP population on the carpet itself.
The hypothesis that the measured Environmental Particle Profiles on individual fibers represent an unbiased statistical sampling of the Environmental Particle Profiles on sets of ten fibers was strongly rejected. The specific program goal was met: to exploit existing computer-assisted SEM/EDS methods to test whether the resulting VSP profiles are useful to quantitatively associate shed fibers with a source carpet.
4. Environmental Particle Groupings have significant weaknesses for investigation of VSP variation and were found to be unsuitable.
The principal weaknesses are that many particle compositions have ambiguous group classifications and are based on only a small percentage of the particle’s composition. The classification ambiguities in the environmental classification scheme are resolved by sequentially applying the classification criteria. Once a particle fits a class it is removed from consideration in the remaining classes. This approach is a reasonable one when targeting specific types of particles, with a defined priority, in a given environmental problem. In practice, an initial classification scheme is used essentially as a presumptive or screening test, to identify candidate particles that might meet a targeted particle type of environmental concern. Images and x-ray spectra of these individual particles, or a sampling of them, can then be examined as part of “confirmatory testing.” Looking at only a small portion of a particle’s composition is also reasonable for the environmental task; if particles don’t meet the presumptive screening criteria, they are conclusively not of interest and are disregarded. For the investigation of VSP variation, however, the ambiguously defined, overlapping environmental classes are poorly suited.
5. Clearly defined, mutually exclusive Target Particle Types (TPTs), based on the commonly occurring elemental profile groupings within samples, were found to be useful for study of the within- and between-carpet variations in VSP occurrence.
The deficiencies of the Environmental Particle Groupings were overcome by defining Elemental Profile Groupings based on the four highest x-ray counts of the 28 elements detected by the computer-assisted SEM/EDS procedure. Groupings occurring at the highest levels in 27 carpet area samples were used to define 68 mutually exclusive TPTs which were then used to study within- and between-carpet variation.
6. Among different areas of the same carpet, most TPTs showed comparable occurrence, or comparable absence. Some TPTs were localized.
Qualitatively, within-carpet variation for the TPTs was usually very low (~ 75% of the time), but occasionally ranged to very high for some TPTs and some areas (~ 13% of the time). This indicates an underlying, roughly even distribution of most particle types, together with occasional localized particle types. The findings do not support a single homogenized VSP distribution on fibers from a carpet, but they conclusively demonstrate that there are many particle types that occur with a sufficiently even distribution to be a useful for characterization.
Page 9 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
The finding of some highly localized variability is not an unreasonable or unexpected result, given the likelihood of local carpet exposures to soiling or staining.
7. Different carpets vary widely in the TPTs and quantities of VSP adhering to their fiber surfaces.
The TPTs used to assess VSP variation among different carpets differed in their occurrence and discrimination potential. Eight of the TPTs occurred at high levels in only one to a few of the 21 carpets studied and another four TPTs occurred at moderate to high levels in several carpets, but at very low levels in most. Three other TPTs occurred over a wide range of levels across the full set of carpets. These 15 TPTs, in particular, are highly discriminating among the set of carpets.
Considering the profiles of VSP observed in each of the carpets, 12 of the 21 carpets are easily distinguished from one another based on qualitative differences and large differences in the frequencies of specific TPTs. The remaining eight carpets show a broad range of frequencies among five specific TPTs. These findings provide a compelling demonstration of the potential of VSP to discriminate among areas from different carpets.
8. When sufficient particles are recovered, individual fibers show highly characteristic patterns of TPTs that closely correspond to those from their originating carpet area.
Very low particle totals were found on some individual fibers, but there was an average of over 700 per fiber. With few exceptions, when totals were over 1000, the TPT occurrences from individual fibers closely followed those from their originating area. The patterns were highly characteristic and showed both qualitative similarity, and similarities in rank and proportion. With lower totals (e.g. 300 to 800 particles), many fibers still showed reasonable similarities with their originating area.
TPTs allowed meaningful comparisons of the occurrences of VSP on individual carpet fibers. For the present methods, a quantitative relationship among the full set of TPTs was not observed. However, the frequent occurrence of similarities in rank and proportionality, in separate experiments using multiple carpets and multiple areas within each carpet, establishes the proof of principle: VSP profiles on shed fibers can be measured, and they regularly correspond to reference samples taken from the area of the source carpet from which they came.
9. Using a set of TPTs, VSP adhering to the surface of individual carpet fibers can be recovered, analyzed by computer-assisted SEM/EDS and used to associate these fibers with the carpet and carpet area from which they came.
This finding is supported by the overall program results, including: − Development and use of a practical method for the recovery of VSP from individual carpet fibers − Demonstration of the regular occurrence of VSP on individual carpet fibers, in quantity and character sufficient to associate them with their carpet area of origin − Development of a method suitable for the study of VSP variation, using a computer- assisted SEM/EDS analysis method based on TPTs
Page 10 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
− Establishing that within-carpet variations show a roughly even distribution for most TPTs − Establishing that between-carpet variations show a wide range in types and quantities of VSP, as demonstrated by TPT profiles
Implications for Policy and Practice
1. The usefulness of VSP to remove fundamental limitations to the probative value of carpet fiber evidence has been demonstrated, providing the impetus and direction for fundamental change in the way that forensic trace evidence is conceptualized, analyzed and used in the criminal justice system.
2. The results of this research are likely extendable, with minor modifications, to other trace evidence types, and are expected to contribute significantly for those types of trace evidence that are have long been considered of low evidential value.
3. An entirely new approach to trace evidence is enabled: comparing different types of trace evidence with one another by way of their adhering VSP.
4. An additional, high priority use for existing crime laboratory SEM/EDS analytical capabilities and related practitioner skills can now be anticipated, guiding the allocation of laboratory resources.
5. A need can be anticipated for policies and practices for evidence collection and processing of crime scenes that are sensitive to requirements for the preservation and analysis of VSP.
Implications for Further Research
The establishment of useful VSP profiles on the surface of individual carpet fibers provides both the impetus and direction for follow-on research. This research can be broadly divided as (1) that focused on developing the specific application of computer-assisted SEM/EDS analysis of VSP on carpet fibers, and (2) that focused on expanding the VSP approach to other applications.
For the specific carpet fiber application, proof of principle has been established with the development of practical methodologies, establishment of workable within-item variability and the measurement of corresponding profiles on individual fibers. The focus for this application now shifts to direct follow-on steps, the most important of which are: − determining which TPTs have the best forensic performance characteristics for carpets − rigorously measuring within and between variability for these TPTs − optimizing the analytical protocol − determining how susceptible shed fibers are to contamination and loss of VSP profiles − development and validation of quantitative methods for the testing the origin of carpet fibers using VSP
For expansion of the VSP approach, additional alternative research directions are − application to other trace evidence types
Page 11 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
− application of other instrumental analysis methods − the use of VSP to associate an environment with an object − more general development and validation of quantitative methods for the use and interpretation of VSP
Page 12 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
I. Introduction
There is a fundamental limitation to probative value of many of the most common types of trace evidence (e.g., fibers, glass, paint) because their characteristics are determined by their manufacture. As mass-produced commodities, probative value is limited to class associations. This has long been appreciated [1-4], and most recently emphasized in the summary assessments in the NRC report [5]. Furthermore, determination of the evidential value of these class associations is extraordinarily problematic. Surveys conducted to determine frequencies of random occurrence of alternative class characteristics are an excellent foundation for expert opinion, but do not allow for quantitative interpretations due to ill-defined populations, the lack of a foundation for randomness within a population, changes in manufacturing practices over time, and variations among analytical methods.[2,3,6] Absent multiple transfers and exceptional circumstances,[7,8] probative value remains difficult to determine and limited by the possibility, or the suggestion of the possibility, that the evidence came from an alternative mass-produced item.
Multiple-transfer cases shatter this limitation. These are cases where a set of different trace evidence materials, found on a suspect, correspond to sources at a crime scene, and/or the reverse: where a set of trace evidence materials, found at the crime scene, correspond to suspect- related sources. When the possibilities of correlation can be discounted, the probative value can become extraordinarily high, even when probabilities for the occurrence of individual trace types are modest, or subject to inherent imprecision in their estimates. The co-occurrence of multiple events of modest frequency is the foundation for all highly probative types of physical evidence, including DNA and fingerprint identifications, and is an inherent aspect of some types of trace evidence, including the comparison of multi-layered structural paints and soil.
This research is part of an effort to radically improve trace-evidence analysis, systematically addressing the fundamental limitations affecting the strength and measurement of probative value, by exploiting the very small particles (VSP) that are present on virtually every material object.[6]
Four founding principles guide this effort:
1. Mixtures of particles have a great potential to proceed systematically toward individualization by providing enhanced probative value via their joint occurrence, with individual particle types occurring at modest, estimable frequencies with testable correlations.
2. Particles are always present in mixtures.
3. As we consider very small particles (VSP), their abundance increases, along with the complexity of the mixture.
4. VSP occurring on the surfaces of commonly used trace evidence types can be recovered, identified, and quantified leading to independent testing of the hypotheses of common origin.
Page 13 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
The first principle has already been discussed, with specific reference to DNA, fingerprints and multiple-transfer evidence as precedence.
Given the value of mixtures, the second principle guides us to broaden our perspective and recognize that mixtures are always there. The traditional focus of forensic particle trace evidence work is on one of a small set of particle types, such as fibers, glass, paint, or hair. Target particles such as these are defined by casework circumstances, and corresponding particles are sought as evidence of transfer and contact.[9] The significance of these particles is that (1) their transfer can be reasonably predicted, based on a hypothesis of contact and (2) they can be efficiently detected among the mixtures of particles that are always present. Other co- occurring particles, smaller, or without a discrete crime scene or suspect source, are largely ignored as “noise.”
The third principle guides us to focus on smaller particles. As we consider them, we have more particles, and the mixture becomes more complex. There is a nearly ten-thousand-fold dimensional gap between conventional trace evidence types and those routinely recovered and analyzed by conventional DNA analysis. The biggest of these are those seen by higher power light and electron microscopy – the respirable or near respirable dusts, which are traditionally ignored in forensic investigations, with the notable exception of gunshot residue (GSR).[10]
The fourth principle states that we can recover, identify and quantify and make practical use of VSP that adhere to the surfaces of conventional trace evidence particles. These VSP “ride piggy- back” on conventional trace evidence. They occur in complex mixtures and include a tremendous variety of particles that are acquired when manufactured materials are exposed to alternative environments. These particles reflect cumulative exposures and conditions; they will be highly characteristic of the local environment [11] and their presence, identity and relative quantities, provide an untapped source of individuality for conventional trace evidence. There is a tremendous potential here: every trace evidence case becomes a multiple-transfer case, with the adhering fine particles providing an independent quantitative means to test hypotheses of common origin. Consider: if these carpet fibers came from that carpet, then the multivariate occurrence of a quantitative profile of fine particles, present on that carpet, ought to be present, subject to statistical sampling, on these fibers.
To unlock this potential, research is required that (1) determines which VSP have useful forensic performance characteristics, (2) develops suitable methods for detection and measurement, and (3) provides data on variation and occurrence that enables reliable statistical interpretation.
The research described in this report develops and tests this approach using the elemental analysis of populations of VSP occurring on the surface of carpet fibers. Carpets are common in indoor domestic and many commercial environments, and they are ubiquitous in automobiles. Carpet fibers are easily shed, easily transferred, easily recognized on careful examination, and easily recovered. The transfer and persistence of fibers have received the most attention of any trace evidence type,[12] and methods for the forensic analysis of fibers are well developed,[13] including national consensus guidelines for morphology, optical properties, composition, and dyes/pigmentation,[14] as well as for examiner training.[15] Overall, fibers are a mature form of trace evidence that has been exploited frequently as associative evidence. Carpet fibers are also
Page 14 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
the most likely candidates, among conventional trace evidence types, to be suitable for this approach: they are subject to long-term exposures, they have a tremendously large exposed surface area, and they are designed to trap small particles. Attempts to clean are seldom thorough, and they have the likely effect of homogenizing the "dust profile."
Methods for computer-assisted SEM/EDS analysis of particles in the size range of interest have been intensively developed in the past ten years for workplace and environmental monitoring,[16-18] and have become increasingly efficient and increasingly focused on particle identification, rather than characterization as methods of chemical imaging have developed.[19,20] In crime laboratories, the methods have been in use since the 1980s (first manually, with progressively more computer assistance) for targeted identification of gunshot residue particles (GSR), based on a combination of their elemental composition and morphology.[10, 21-24] The summary of the FBI Laboratory's Gunshot Residue Symposium[23] provides an excellent sense for the extent of activity in this area. The future of these computer- assisted combinations of chemical and microscopical analysis, as applied to forensic trace evidence analysis, has been foreshadowed by Roux.[25] It is a good fit, with respect to existing laboratory skills and utilization of existing equipment, to extend computer-assisted SEM/EDS analyses to fine particles adhering to the surfaces of conventional trace evidence materials.
For initial investigations, it was reasonable to use existing computer-assisted SEM/EDS particle analysis protocols and classification criteria, even though they were designed for environmental applications, as the methods are rigorously standardized and the particle classification criteria are explicitly defined.[18] For efficient analysis of fine particles from carpet fibers using computer- assisted SEM/EDS, methods for particle removal and transfer to SEM stubs must be developed.
The goals of the present research were to (1) to develop the methods needed to quantitatively remove VSP from carpet fibers and prepare them for SEM/EDS analysis, and (2) to exploit existing computer-assisted SEM/EDS methods to test whether the resulting fine particle profiles are useful to quantitatively associate shed fibers with a source carpet.
Our specific hypothesis was that carpet fibers from a source carpet will bear a measurable fine particle profile that is a function of an unbiased statistical sampling of the fine particle population present on the source carpet. To test this hypothesis and put the results in context, we defined four objectives: (1) Develop methods, compatible with existing fiber analysis protocols, and using currently available crime laboratory resources, to quantitatively remove and analyze VSP adhering to carpet fibers. (2) Use these methods to determine within-item variation (VSP profiles within the source carpet). (3) Analyze VSP adhering to fibers that have been shed from the source carpets, and determine if the profiles occurring on these fibers are consistent with an unbiased statistical sampling from the source carpet population. (4) Conduct a broader qualitative survey of carpet particle profiles to explore between- item variation.
Page 15 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
II. Methods
A. Carpet Sample Selection Carpets were selected for three purposes: Development of protocols for recovery of particles from fiber surfaces Analysis of within-carpet variation Survey of a broader set of carpets
1. Carpet Selection for Development of Protocols for Recovery of Particles from Fiber Surfaces Practitioner review of proposed generic fiber types for development of particle recovery protocols revealed an overwhelmingly dominant incidence of Nylon fibers among carpet fibers occurring in casework (75% or more), and an overwhelmingly dominant incidence of trilobal cross-sections (85 to 90%). Trilobal cross section designs are also specifically meant to trap debris, and thus provide an appropriate “worst case” medium for development of particle recovery methods. Accordingly, trilobal nylon carpet fibers were chosen for the testing of particle recovery protocols. Beige, TiO2-delustered trilobal nylon carpet fibers (Figure 1) were collected from the bottom step of the household entry way stairs from the residence of one of the SFI staff.1
Figure 1. Polarized light microscopy of a representative trilobal Nylon fiber used for development of particle recovery protocols shown at two different magnifications with plane polarized light (above) and in-between crossed polars (below). The photomicrographs in the right column have the focus raised to illustrate the fiber’s trilobal cross section. The mounting medium is nD 1.570.
1 13539 Lavender Mist Lane, Centreville, VA, also designated as Carpet A. Page 16 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
2. Carpet Selection for Analysis of Within-Carpet Variation To cover a reasonable breadth of settings, nine carpets were used for the study of within-carpet variation. Represented were three residential carpets, three automobile carpets and three carpets from workplace settings. Carpets in SFI staff residences, vehicles and family workplace settings were selected for convenience. These carpets were not meant to be representative of a population, but to cover a range of settings so that a range of within-carpet variation could be studied. Fiber types and cross-sections were determined by polarized light microscopy[14,15] and were reviewed by practitioners for reasonable representation of types encountered in casework. Of these nine carpets, six were composed of nylon fibers (cross sections: five trilobal, one square with hollow filaments) and three were composed of polyester fibers (cross sections: two circular, one trilobal). Table 1 provides a listing of these carpets. Description and documentation of the carpet locations and fiber types is given in Appendix A. Carpet Sampling for Within-Item Variation.
3. Carpet Selection for the Broader Survey of Carpets Twelve additional carpets were selected to allow better understanding of between-item variation and to serve as a foundation for the design of follow-on studies. Practitioner input was that fiber analyses related to commercial or workplace carpets are much less frequently encountered in forensic casework, compared to automobile and residential carpets. Their assessment was also that that fibers encountered in casework are fairly evenly split between residential and vehicle carpets, perhaps with slightly more residential carpets. Accordingly, we adjusted the scope of the types of carpet fibers considered to include round cross sections and the broader survey of carpets was limited to residential and vehicular carpets (seven residential and five vehicular). For convenience, carpets were selected from the residences and vehicles of SFI staff, relatives and neighbors. Again, these carpets were not meant to be representative of a population, but to cover a broader range of settings so that a range of between-carpet variation could be appreciated. Of these 12 carpets, 11 were composed of trilobal nylon fibers and one was composed of very dark fibers of circular cross section. Table 2 provides a listing of these carpets. Description and documentation of the carpet locations and fiber types is given in Appendix B. Additional Carpet Sampling for Between-Item Variation.
B. Sampling of Fibers from Carpets Sampling fibers by contact was initially considered, similar to the experiments conducted by Roux et al.[26] This method was rejected after practitioner review and replaced by direct cutting of looped piles from the carpets. Direct cutting was the method used by practitioners in casework, having been adopted to ensure that fibers were actually from the carpet source, as opposed to loose fibers, that could be alleged to have come from another source. Lengths of cut fibers were not individually measured, but ranged from approximately 10 to 15mm in long.
Carpets used for analysis of within-item variation were sampled from three areas, spaced from one to three feet apart. Homogenized dust samples (by vaccum) from each of the carpet locations will also be taken for reference purposes. Collection locations for each of the carpet samples are described and illustrated in Appendix A. Carpet Sampling for Within-Item Variation and Appendix B. Additional Carpet Sampling for Between-Item Variation.
Page 17 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 1. Carpets Selected for Analysis of Within-Carpet Variation2
Carpet Fiber Fiber Type of Description Designation Composition Cross Section Location
A Nylon Trilobal Residence Base of the stairs near front door
BH Nylon Trilobal Residence Basement hallway
PH Polyester Trilobal Residence Top of stairs near front door
BV Polyester Round Vehicle 2010 Toyota RAV4 driver side footwell
F Polyester Round Vehicle 2002 Ford Focus trunk area
PV Nylon Trilobal Vehicle 2005 Ford Taurus passenger side footwell Square MT Nylon Workplace Middle school lecture hall Hollow Filament
PL Nylon Trilobal Workplace Office building second floor hallway
W Nylon Trilobal Workplace Office building hallway near entrance
2 Description and documentation of the carpet locations and fiber types is given in Appendix A. Carpet Sampling for Within-Item Variation. Page 18 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 2. Additional Carpets Selected for Analysis of Between-Carpet Variation3
Carpet Fiber Fiber Type of Description Designation Composition Cross Section Location
R1 Nylon Trilobal Residence Living room
R2 Nylon Trilobal Residence Basement
R3 Nylon Trilobal Residence Basement
R4 Nylon Trilobal Residence Living room Trilobal R5 Nylon Residence Top of stairs, second floor Thin lobed, Y
R6 Nylon Trilobal Residence Living room
R7 Nylon Trilobal Residence Base of the stairs near front door
V1 Nylon Trilobal Vehicle 2008 Honda CRV middle front footwell
V2 Nylon Trilobal Vehicle 2006 Lexus LX70 trunk area
V3 Nylon Trilobal Vehicle 2001 Honda Odyssey trunk area Not V4 Round Vehicle 2009 Ford Focus trunk area Determined 2008 Toyota Highlander front passenger V5 Nylon Trilobal Vehicle footwell
3 Description and documentation of the carpet locations and fiber types is given in Appendix B. Additional Carpet Sampling for Between-Item Variation. Page 19 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
C. SEM Imaging and Qualitative Assessment of Particle Abundance on Fiber Surfaces Fibers were mounted on carbon tape affixed to an aluminum SEM stub and lightly carbon-coated using a Cressington Auto Carbon Coater 108c with carbon evaporation conducted at 3.8 volts for 6 seconds. The fibers were then imaged using a Tescan Vega II scanning electron microscope with an accelerating voltage of 5 kV and a probe current of PC = 10. No charging was observed and no spontaneous scattering of particles was observed.
D. Isolation of Particles from Fibers (Protocol Development) Five alternative fluids were tested using a set of alternative agitation methods and agitation times. The five fluids were acetone, ethanol, hexanes, 5% aqueous ethanol, and 5% aqueous sodium hexametaphosphate. Acetone is the liquid medium recommended for preparing soil and dust samples for automated SEM analysis.[27] Ethanol is an effective deflocculant that has long been used to separate aggregates of fine particles adhering to each other, especially for preparation of palynological samples.[28] Hexanes were used as a representative non-polar liquid to test their relative effectiveness, given that all of the others being tested were polar in nature. Dilute aqueous alcohol solutions are routinely used in our soil separation methods and are recommended for deflocculation during settling velocity separations.[29] Dilute (5%) aqueous sodium hexametaphosphate is commonly used by soil scientists to deflocculate clay and silt particles for separation by settling velocity and is used as a deflocculant in the ASTM Standard Test Method for Particle-Size Analysis of Soils.[30]
The methods of agitation were sonication, vortex mixing, and a combination of the two. Sonication was performed using a Cole Palmer model 08849-00 ultrasonic cleaner, using the single, fixed setting. Durations of sonication were limited to a maximum of ten minutes, as there is strong evidence that with sonication times exceeding ten minutes particles as hard as quartz may begin to break apart into smaller grains.[31] Table 3 shows agitation conditions used with each fluid.
Table 3. The Set of Agitation Conditions used for Each Fluid During Development of the Particle Isolation Protocol
Combinations of Sonication Only Vortex Mixing Only Sonication and Vortex Mixing 5 seconds vortexing 10 seconds 10 seconds 10 seconds sonication 5 seconds vortexing 5 seconds vortexing followed by two repetitions of: 30 seconds 60 seconds 30 seconds sonication 5 seconds vortexing 5 seconds vortexing followed by ten repetitions of: 60 seconds 60 seconds sonication and 5 seconds vortexing 5 minutes 10 minutes
Page 20 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
After each agitation experiment, the fiber was removed from the solvent using clean, fine-tipped forceps and gently placed on carbon tape mounted on an aluminum SEM stub. The agitation experiments and fiber mounting were conducted in a clean bench to minimize environmental contamination. Following particle removal processes and mounting for SEM, fibers were imaged by SEM to determine whether all adhering particles had been removed or not. For each fiber, an attempt was made to document the dirtiest areas (those with the most adhering particles), the cleanest areas (those with the fewest particles), and those with an “average” or typical level of cleanliness as observed on the fiber. At least eight images were taken documenting the appearance of each fiber.
E. Isolation of Particles from Fibers (Finalized Method)4 All procedures were conducted on the clean bench. Prior to starting, a significant volume (roughly 100 mL) of reagent grade ethanol (99.5%) was filtered through a polycarbonate filter (Millipore Isopore™ Membrane Filters, 0.4 μm HTTP). All test tubes, transfer pipets, forceps and razor blades were pre-washed with the particle-free ethanol.
Approximately 0.5 mL of pre-filtered reagent grade ethanol (99.5%) was transferred to a 1.5 mL micro-centrifuge tube using a transfer pipet. The fiber(s) to be analyzed were placed inside the tube using forceps. The tube was then sonicated in an ultrasonic cleaner (Cole Palmer model 08849-00) for ten minutes. After sonication the fiber(s) were removed from the tube using forceps, leaving behind a particle suspension in ethanol.
A polycarbonate filter (Millipore Isopore™ Membrane Filters, 0.4 μm HTTP) was placed on a support pad and then directly on a vacuum filtration apparatus (with no upper funnel attached). The vacuum was applied to the filter and then a small square region (roughly 5 mm by 5 mm) was cut out of the center of the filter using a Teflon-coated razor blade and left in place. A wide- tipped (1.5mm ID) transfer pipet was used to re-suspend the fine particles in the ethanol and then suction up the ethanol particle suspension. The suspension was slowly transferred from the pipet to the small square cut out of the filter while the vacuum pulled the ethanol through the filter. The filter was left on the support pad to dry, after which the small square was transferred to carbon tape on an SEM stub using forceps. The SEM stub was carbon-coated using a Cressington Auto Carbon Coater 108c with carbon evaporation conducted at 3.8 volts for 6 seconds and evaluated for particle dispersal by imaging in Tescan Vega II scanning electron microscope using an accelerating voltage of 5 kV and a probe current of PC = 10. In all instances the particles were well-dispersed, with the typical appearance as in Figure 2.
A process control blank was prepared alongside each batch of samples processed (pre-filtered ethanol sonicated for ten minutes in an empty tube and otherwise treated in an identical manner).
4 One of the research products is this method, and it is described in detail in Appendix C. Illustrated Fine Particle Removal and Mounting Method. Page 21 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Figure 2. Typical appearance of the prepared carbon-coated SEM stubs upon inspection prior to computer-assisted SEM/EDS analysis. The particles are well-dispersed.
F. Computer-Assisted SEM/EDS Analysis of Particles Standardized computer-assisted SEM/EDS analyses were performed by Gateway Analytical, LLC. Analyses were conducted on a total of 120 samples, along with 12 process blanks. These samples are summarized in Table 4. The 27 sets of ten fibers were collected from the nine carpets listed in Table 1 (one set from each area sampled). The 10-fiber sets were used to represent the population of particles at that area of the carpet. The 81 individual fibers, three from each of the 27 areas, were used to represent individual shed fibers from these areas. The 12 samples from each of the carpets in Table 2 each consisted of ten fibers and were used to represent populations of particles for those carpets. The 12 process blanks were those run alongside the processing of each batch of fiber samples. The sample designation scheme for the fiber samples from the Carpets in Table 1 is shown in Table 5, using Carpet A as an example.
Table 4. Summary of Samples and Process Blanks
Carpets Selected for Analysis of Within-Item Variation (Table 1) 27 samples sets of ten fibers from each of the three areas on each of the nine carpets 81 samples 3 individual fibers from each of the three areas on each of the nine carpets
Carpets Selected for Broader Survey of Carpets (Table 2) 12 samples sets of ten fibers from one area on each carpet
Process Blanks 12 samples one process blank for each batch of fiber samples processed
Page 22 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 5. Summary of Sample Designations for Fiber Samples from Carpet A
Sample Description Designation A1-10 Area 1 of Carpet A, 10 Fiber Sample A1-1, A1-2, A1-3 Area 1 of Carpet A, individual fiber samples 1, 2, and 3 A2-10 Area 2 of Carpet A, 10 Fiber Sample A2-1, A2-2, A2-3 Area 2 of Carpet A, individual fiber samples 1, 2, and 3 A3-10 Area 3 of Carpet A, 10 Fiber Sample A3-1, A3-2, A3-3 Area 3 of Carpet A, individual fiber samples 1, 2, and 3
The computer-assisted SEM/EDS analysis was performed on an Aspex Corporation PSEM Explorer SEM-EDS system using the Automated Feature Analysis (AFA) program within the Aspex Corporation Perception software. Analysis was performed under high vacuum conditions utilizing a 20.0kV accelerating voltage, backscatter electron detector (BSED), working distance of approximately 15mm-17mm, and spot size of approximately 37%. The magnification for the analysis was 2,000X with the number of electronic fields set at a maximum of 5 x 5. A grid dimension of 256 x 256 was used with a dwell time per pixel of 8µs for searching and 16µs for measuring. The size criteria for analysis were a minimum size of 0.3µm and a maximum size of 50.0µm. The maximum number of particles analyzed, as set by program parameters, was 4000. EDS parameters had a nominal duration of 3s, a maximum of 6s, a minimum count of 300 and a target count of 2500. An EDS Copper calibration check was performed prior to, and following each analysis. Operational settings restricted detection to the 28 elements listed in Table 6, which are given along with the x-ray lines used for detection. These elements were chosen to follow an existing environmental analysis protocol with a mix of rarely encountered and commonly occurring elements among a set of 28. The number of elements (among those detectable by EDS) is not restricted by the SEM/EDS or by the software and the assortment of elements can be changed. The number of elements selected affects the overlap of x-ray lines, but ambiguities are resolved by the x-ray detection software using known correlated x-ray emissions for the specific elements. Specific x-ray windows used for elemental detection for each of the elements are given in Appendix E-12. X-Ray Count Windows.
Raw datasets for each computer-assisted SEM/EDS run consisted of summary statistics along with individual particle analysis data. Summary statistics were: total number of fields analyzed, total search area, total number of particles analyzed, and number of particles classified into each of ten pre-defined Environmental Particle Groups. Individual particle data were a particle index number, a set of particle size and shape parameters, the four elements in the particle’s EDS spectrum having the highest x-ray counts, and the corresponding four x-ray counts. Particle size and shape parameters were the average, maximum and minimum particle diameters, the aspect ratio, area and perimeter. Classification among the ten pre-defined Environmental Particle Groups was based on percentages of total x-ray counts for specified elements. Alternative criteria were applied in sequence until a criterion was met. The specific criteria are given in Table 7.
Page 23 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 6. The 28 Elements Detected by the Automated EDS Procedure
Sodium (Kα, Kβ) Magnesium (Kα, Kβ) Aluminum (Kα, Kβ) Silicon (Kα, Kβ) Sulfur (Kα, Kβ) Chlorine (Kα, Kβ) Calcium (Kα, Kβ) Titanium (Kα, Kβ) Chromium (Kα, Kβ) Manganese (Kα, Kβ) Iron (Kα, Kβ) Nickel (Kα, Kβ) Copper (Kα, Kβ) Zinc (Kα, Kβ) Bromine (Lα, Lβ) Strontium (Lα, Lβ) Zirconium (Lα, Lβ, Lγ) Silver (Lα, Lβ, Lγ) Tin (Lα, Lβ, Lγ) Antimony (Lα, Lβ, Lγ) Barium (Lα, Lβ, Lγ) Tungsten (Mα) Gold (Mα) Mercury (Mα) Lead (Mα) Bismuth (Mα) Lanthanum (Lα, Lβ, Lγ) Cerium (Lα, Lβ, Lγ)
Table 7. Sequentially Applied Criteria for Environmental Particle Groupings
Environmental Percent of Total X-ray Counts for the 28 Application Order Particle Group Elements in Table 6 1 Cl/Ca/S Cl>=10 and Ca>=10 and S>=10 2 Na/Cl Na>=10 and Cl>=10 and Ca<10 and S<10 3 Al/Si Al>=10 and Si>=20 4 Ca/S Ca>=10 and S>=10 5 Fe-rich Fe>=10 6 Ca-rich Ca>=60 7 Si-rich Si>=40 8 Al-rich Al>=20 9 Na-rich Na>10 10 Misc all other particles
G. Analysis of Environmental Particle Groupings Frequencies for the Environmental Particle Groupings obtained from the computer-assisted SEM/EDS analyses were analyzed using the method of Kelley,[32] based on a multinomial distribution with maximum-likelihood estimation and chi-square testing. This statistical treatment assumes that a sample of size N (the particles adhering to the questioned carpet fiber) has been drawn from a population of interest (all of the particles adhering to fibers on the control carpet). As the sample is drawn, each of the particles is classified into one of k categories. The categories must be mutually exclusive and together include all elements in the population. Comparison between the questioned and known samples is based on the assumption that the frequencies of particles observed in the sample (questioned carpet fiber) are representative of the proportions in the population (control carpet), and that the population has been sampled randomly in on the questioned fiber. The control carpet particle group population frequencies were determined based on isolation and analysis of particles from a pooled sample of ten fibers from one carpet area. Questioned fiber particle group frequencies were those from individual fibers taken from the same carpet areas. Three individual fibers were analyzed for each area.
Page 24 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
H. Within-Sample Elemental Profile Classes For classification of more complete elemental profiles the four highest x-ray counts were normalized. Starting with the first particle, each successive particle was checked for qualitative and quantitative correspondence. Qualitative correspondence was determined by the presence, in the other particle, of any elements needed to account for at least 85% of the normalized x-ray counts. Quantitative correspondence was determined by normalized x-ray counts within a tolerance of 30% of one another, according to Equation 1, where C1 and C2 are normalized x-ray counts for the two corresponding elements. The set of corresponding particles defined the first group. This process was repeated for each ungrouped particle, testing the remaining ungrouped particles and defining further groupings. The values of 0.85 for the qualitative correspondence threshold and 30% for the quantitative x-ray count tolerance were chosen after consultation with subject matter experts5 based on expected instrument detection thresholds and x-ray count variability.
| (C1 – C2) | Equation 1. 0.30 > (C1 + C2) / 2)
I. Selection, Definition and Frequency of Target Particle Types Target Particle Types (TPTs) were defined based on those within-sample Elemental Profile Classes occurring frequently in samples from the nine carpets listed in Table 1. Analyses were conducted on sets of ten fibers from each of the three areas sampled for each of the nine carpets; a total of 27 analyses. Elemental Profile Classes occurring with a frequency of greater than 1% in any of the 27 analyses were selected. A set of mutually-exclusive TPTs were defined based on grouping of closely related and overlapping selected Elemental Profile Classes.6 Frequencies of each of the TPTs were determined for each of the 120 sample analyses and 12 sample process blanks. Limits of Detection (LODs) for each of the TPTs were defined based as 3 times the sample standard deviation of the process blanks.
5 David Exline of Gateway Analytical, LLC and Richard Brown of MVA Scientific Consultants, Inc. 6 Details of the definition of the Target Particle Types are given as part of the Results. Page 25 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
III. Results
A. Isolation of Particles from Fibers Acetone, ethanol, hexanes, 5% aqueous ethanol, and 5% aqueous sodium hexametaphosphate were evaluated for their efficiency of fine particle removal from the surfaces of trilobal carpet fibers using a range of agitation conditions. SEM images documenting the results of the experimentation testing the particle removal processes can be found in Appendix D: Fiber Particle Removal Documentation Dataset.
1. Acetone A noticeable number of particles remained adhering to the fibers after essentially all of the acetone agitation experiments. It was not clear whether sonication, vortex mixing, or a combination of the two was most effective, nor was there an apparent trend relating to agitation times. It was clear that acetone is not a good candidate for quantitative removal of small particles from fibers.
2. Ethanol The ethanol agitation methods did a considerably better job of removing particles from fibers than either the acetone or hexanes, and a slightly better job than the 5% aqueous ethanol solution. Ethanol was comparable to (or slightly poorer than) a 5% aqueous sodium hexametaphosphate solution. The ten-minute sonication experiment for ethanol resulted in a very clean fiber, and was the most effective agitation method based on the cleanliness of the fiber after treatment. Vortex mixing alone was somewhat less effective than sonication alone. A combination of sonication and vortex mixing was not noticeably more effective than sonication alone, making the additional required time and effort unjustified. Ethanol is a good candidate for quantitative removal of small particles from fibers.
3. Hexanes A noticeable number of particles remained adhering to the fibers after virtually all of the hexanes agitation experiments. Of the different agitation treatments, the ten-minute combination of vortex mixing and sonication resulted in the cleanest fiber, although it was not as clean as the fiber treated with ten-minute sonication in ethanol. Hexanes are not a good candidate for quantitative removal of small particles from fibers.
4. 5% Aqueous Ethanol A noticeable but small number of particles remained adhering to the fibers after virtually all of the 5% ethanol agitation experiments. Of the different agitation treatments, the ten-minute combination of vortex mixing and sonication resulted in the cleanest fiber, and it was almost as clean as the fiber treated with ten-minute sonication in ethanol. The fibers treated with other agitation times and methods retained more particles than those treated with pure ethanol. 5% aqueous ethanol is not as good of a candidate for quantitative removal of small particles from fibers as pure ethanol.
5. 5% Aqueous Sodium Hexametaphosphate The 5% aqueous sodium hexametaphosphate agitation experiments appeared to do a considerably better job of removing particles from fibers than either the acetone or the hexanes,
Page 26 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
and a slightly better job than either the pure ethanol or the 5% aqueous ethanol solution. However, the 5% aqueous sodium hexametaphosphate left a residue on the fibers after washing. This residue is rich in sodium and phosphorus, and is expected to impact the SEM/EDS particle analysis by its presence on or among particles washed from the fibers. Particles of this composition (formed by drying) could potentially be washed away during filtration using a separate washing step, but this is an undesirable extra source of possible contamination.
These findings resulted in the finalized fine particle removal and mounting method referred to in the Methods section and described in detail in Appendix C. Illustrated Fine Particle Removal and Mounting Method.
B. Computer-Assisted SEM Analyses The computer-assisted SEM analyses conducted on the 120 samples and 12 process blanks are provided in Appendix E. Computer-Assisted SEM-EDS Analysis Dataset. Individual spreadsheets are provided within 11 Excel Workbooks. Nine of these workbooks correspond to the nine carpets selected for analysis of within-carpet variation, as listed in Table 1. Worksheets bear sample designations following the scheme illustrated in Table 5. A tenth workbook corresponds to the additional carpets selected for analysis of between-carpet variation, as listed in Table 2. Worksheets bear the carpet designations. The final workbook contains spreadsheets corresponding to the process blanks. Worksheets bear the designations B0 (B-zero) through B11.
Particle numbers recovered and analyzed from the 39 sets of ten fibers are summarized in Table 8. Those from the 12 process blanks are summarized in Table 9 and those from the 81 individual fibers are summarized in Table 10. Descriptive statistics are found Tables 11 and 12.7 The maximum number of particles analyzed, as set by program parameters, was 4000. For sets of ten fibers, this number was reached in 41% of the samples (16 of 39), compared to 5% of the single fibers (4 of 81), and none of the process blanks. On the average, sets of ten fibers showed 2780.4 particles (n = 39, SD = 1353.0); single fibers showed 720.7 particles (n = 81, SD = 943.8); and blanks showed 175.6 particles (n = 12, SD = 126.8). Particles were well dispersed on the SEM stubs as indicated by very low averages for the number of particles present per field (as documented in Appendix E. Computer-Assisted SEM-EDS Analysis Dataset). Most samples had an average of much less than one particle per field and no sample had an average of more than three.
Histograms of particle sizes for each of the 132 samples are given as part of Appendix F. Particle Descriptive Statistics and Histograms. Each sample has two histograms to allow examination of the distribution of the coarser as well as the finger particles. Figure 3 shows histograms from sample A3-10 as an example.
Environmental Particle Groupings for each of the sets of ten fibers sampled from each area of the nine carpets in Table 1 are summarized in Table 13, grouped by Residential, Vehicular and Workplace carpets. Tables with Environmental Particle Groupings for each of the carpet areas and each of the corresponding individual fibers are given in Appendix G. Environmental Particle Groupings Dataset.
7 Full descriptive statistics can be found in the Excel file Appendix F. Particle Numbers Descriptive Statistics. Page 27 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 8. Numbers of Particles Recovered and Analyzed from Sets of ten Fibers8
Residential Carpets Vehicular Carpets Workplace Carpets 3001 1233 4000 Carpet A 4000 Carpet BV 3613 Carpet MT 2750 4000 1431 1564 2948 445 4000 Carpet BH 4000 Carpet F 1179 Carpet PL 2169 4000 359 3662 1363 4000 2896 Carpet PH 4000 Carpet PV 4000 Carpet W 4000 4000 1005 710 Carpet R1 642 Carpet V1 3422 Carpet R2 4000 Carpet V2 1803 Carpet R3 4000 Carpet V3 3485 Carpet R4 3206 Carpet V4 1030 Carpet R5 4000 Carpet V5 518 Carpet R6 4000 Carpet R7 4000
Table 9. Numbers of Particles Recovered and Analyzed from Process Blanks8
Process Blanks Blank B0 138 Blank B1 227 Blank B2 89 Blank B3 279 Blank B4 215 Blank B5 235 Blank B6 89 Blank B7 465 Blank B8 241 Blank B9 24 Blank B10 32 Blank B11 73
8 Limited to 4000 particles by program settings. Page 28 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 10. Numbers of Particles Recovered and Analyzed from Individual Fibers
Residential Carpets Vehicular Carpets Workplace Carpets 164 754 498 Area 1 161 Area 1 1107 Area 1 127 490 307 123 872 1500 122 Carpet A Area 2 1110 Carpet BV Area 2 1757 Carpet MT Area 2 190 1783 2121 440 67 521 214 Area 3 306 Area 3 574 Area 3 47 85 365 61 244 437 1492 Area 1 345 Area 1 293 Area 1 1742 239 464 848 421 286 505 Carpet BH Area 2 312 Carpet F Area 2 129 Carpet PL Area 2 494 691 397 518 4000 237 375 Area 3 504 Area 3 213 Area 3 692 234 166 454 70 809 514 Area 1 59 Area 1 438 Area 1 464 205 604 535 137 4000 419 Carpet PH Area 2 147 Carpet PV Area 2 4000 Carpet W Area 2 367 4000 3779 280 504 674 320 Area 3 711 Area 3 950 Area 3 258 1568 330 152
Table 11. Descriptive Statistics for Particle Numbers Recovered and Analyzed
10 Fiber sets Single Fibers Blanks Count 39 Count 81 Count 12 Mean 2780.4 Mean 727.0 Mean 175.6 Standard Error 216.6 Standard Error 104.8 Standard Error 36.6 Standard Deviation 1353.0 Standard Deviation 943.0 Standard Deviation 126.8 Median 3422 Median 437 Median 176.5 Minimum 359 Minimum 47 Minimum 24 Maximum 4000 Maximum 4000 Maximum 465
Page 29 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 12. Descriptive Statistics by Carpet Type for Particle Numbers Recovered and Analyzed9
10-Fiber Sets9 Residential Vehicular Workplace Count 10 Count 8 Count 3 Mean 3428.5 Mean 2001.6 Mean 2861.2 Standard Error 327.4 Standard Error 427.0 Standard Error 218.8 Standard Deviation 1035.3 Standard Deviation 1207.6 Standard Deviation 378.9 Median 3833.5 Median 1947.7 Median 2771.3 Minimum 642 Minimum 518 Minimum 2535.3 Maximum 4000 Maximum 3485 Maximum 3277 Individual Fibers
Residential Vehicular Workplace Count 27 Count 27 Count 27 Mean 700.6 Mean 1007.9 Mean 453.7 Standard Error 200.8 Standard Error 222.9 Standard Error 74.9 Standard Deviation 1043.1 Standard Deviation 1158.0 Standard Deviation 389.1 Median 312 Median 521 Median 419 Minimum 59 Minimum 129 Minimum 47 Maximum 4000 Maximum 4000 Maximum 1742
Figure 3. Particle size histograms for sample A3-10. Histograms for all 132 samples can be found in Appendix F. Particle Descriptive Statistics and Histograms.
9 A single mean value was used for the nine carpets where three areas were sampled. Page 30 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 13. Environmental Particle Groupings for the 27 Areas of the Nine Carpets in Table 1
Residential Carpet A Carpet BH Carpet PH Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Class Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Al/Si 568 0.189 485 0.121 1425 0.356 273 0.093 817 0.204 219 0.055 61 0.045 39 0.010 277 0.069 Al-rich 72 0.024 39 0.010 125 0.031 28 0.009 86 0.022 44 0.011 27 0.020 14 0.004 39 0.010 Ca/S 617 0.206 324 0.081 304 0.076 85 0.029 84 0.021 291 0.073 73 0.054 77 0.019 154 0.039 Ca-rich 316 0.105 193 0.048 312 0.078 297 0.101 331 0.083 207 0.052 517 0.379 1971 0.493 1408 0.352 Cl/Ca/S 1 0.000 0 0.000 3 0.001 2 0.001 0 0.000 0 0.000 1 0.001 0 0.000 2 0.001 Fe-rich 275 0.092 35 0.009 347 0.087 276 0.094 508 0.127 1335 0.334 19 0.014 52 0.013 227 0.057 Misc 345 0.115 498 0.125 367 0.092 775 0.263 777 0.194 1296 0.324 286 0.210 1209 0.302 868 0.217 Na/Cl 26 0.009 3 0.001 39 0.010 20 0.007 18 0.005 3 0.001 53 0.039 26 0.007 78 0.020 Na-rich 486 0.162 2327 0.582 570 0.143 1080 0.366 1085 0.271 480 0.120 289 0.212 594 0.149 812 0.203 Si-rich 295 0.098 96 0.024 508 0.127 112 0.038 294 0.074 125 0.031 37 0.027 18 0.005 135 0.034 Total 3001 1.000 4000 1.000 4000 1.000 2948 1.000 4000 1.000 4000 1.000 1363 1.000 4000 1.000 4000 1.000 Vehicular Carpet BV Carpet F Carpet PV Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Class Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Al/Si 524 0.425 1494 0.414 563 0.393 137 0.308 198 0.168 105 0.292 1859 0.465 1692 0.42 334 0.332 Al-rich 24 0.019 68 0.019 32 0.022 7 0.016 13 0.011 8 0.022 149 0.037 131 0.03 17 0.017 Ca/S 23 0.019 54 0.015 14 0.010 6 0.013 8 0.007 7 0.019 10 0.003 147 0.04 12 0.012 Ca-rich 142 0.115 138 0.038 79 0.055 34 0.076 68 0.058 58 0.162 212 0.053 239 0.06 53 0.053 Cl/Ca/S 0 0.000 0 0.000 0 0.000 2 0.004 0 0.000 0 0.000 3 0.001 0 0.00 0 0.000 Fe-rich 110 0.089 424 0.117 156 0.109 63 0.142 148 0.126 67 0.187 605 0.151 819 0.20 302 0.300 Misc 146 0.118 348 0.096 285 0.199 59 0.133 399 0.338 49 0.136 413 0.103 476 0.12 113 0.112 Na/Cl 0 0.000 28 0.008 13 0.009 10 0.022 106 0.090 1 0.003 53 0.013 19 0.00 25 0.025 Na-rich 31 0.025 68 0.019 36 0.025 9 0.020 84 0.071 3 0.008 289 0.072 114 0.03 41 0.041 Si-rich 233 0.189 991 0.274 253 0.177 118 0.265 155 0.131 61 0.170 407 0.102 363 0.09 108 0.107 Total 1233 1.000 3613 1.000 1431 1.000 445 1.000 1179 1.000 359 1.000 4000 1.000 4000 1.00 1005 1.000
Page 31 of 76 This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 13. (Continued)
Workplace Carpet MT Carpet PL Carpet W Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Class Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Count Freq. Al/Si 1191 0.298 1167 0.424 492 0.315 257 0.064 516 0.238 729 0.199 1002 0.346 1758 0.440 251 0.354 Al-rich 104 0.026 109 0.040 63 0.040 20 0.005 42 0.019 63 0.017 123 0.042 134 0.034 20 0.028 Ca/S 46 0.012 25 0.009 17 0.011 3097 0.774 468 0.216 1118 0.305 175 0.060 538 0.135 97 0.137 Ca-rich 656 0.164 138 0.050 82 0.052 159 0.040 176 0.081 562 0.153 176 0.061 233 0.058 103 0.145 Cl/Ca/S 0 0.000 2 0.001 0 0.000 0 0.000 10 0.005 7 0.002 5 0.002 8 0.002 2 0.003 Fe-rich 591 0.148 168 0.061 109 0.070 84 0.021 238 0.110 330 0.090 175 0.060 348 0.087 55 0.077 Misc 670 0.168 408 0.148 200 0.128 213 0.053 269 0.124 503 0.137 325 0.112 426 0.107 86 0.121 Na/Cl 5 0.001 28 0.010 16 0.010 0 0.000 5 0.002 11 0.003 86 0.030 1 0.000 0 0.000 Na-rich 61 0.015 246 0.089 363 0.232 31 0.008 71 0.033 91 0.025 507 0.175 17 0.004 9 0.013 Si-rich 676 0.169 459 0.167 222 0.142 139 0.035 374 0.172 248 0.068 322 0.111 537 0.134 87 0.123 Total 4000 1.000 2750 1.000 1564 1.000 4000 1.000 2169 1.000 3662 1.000 2896 1.000 4000 1.000 710 1.000
Page 32 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
C. Statistical Testing of Environmental Particle Groupings The specific hypothesis for the Environmental Particle Groupings was that carpet fibers from a source carpet will bear a measurable fine particle profile that is a function of an unbiased statistical sampling of the fine particle population present on the source carpet. Per the experimental design, the fine particle population on an area of the source carpet was represented by a set of ten fibers. Individual fibers taken from these same areas were used to represent individual evidentiary fibers, whose fine particle profiles were to be tested against the carpet fine particle population. Working with the computer-assisted SEM/EDS results in Appendix G, statistical analysis resulted in the clear rejection of the hypothesis. Tests of homogeneity resulted in values of the chi-square statistic far in excess of those expected under the null hypothesis; even at the highest levels of α.10 Details of the calculations of the chi-square statistic are given in Appendix H. Environmental Groupings Within-Carpets Population Tests. The hypothesis that the measured Environmental Particle Profiles on individual fibers represent an unbiased statistical sampling of the Environmental Particle Profiles on sets of ten fibers is strongly rejected.
D. Elemental Profile Groupings and Classes Specific weaknesses of the Environmental Particle Groupings include: many particle compositions with ambiguous group classification, a group classification process that is dependent on the order of classification, and insensitivity to much of a particle’s elemental profile. Alternative, Elemental Profile Groupings were designed to address these weaknesses and used to group particles of similar elemental compositions within samples.11 Elemental Profile Groupings occurring with frequencies greater than 1% in each of the 27 10-fiber carpet area samples are given in Appendix I. Elemental Particle Groupings Occurring with Frequencies Greater than One Percent. As an example, Table 14 shows the data for Carpet A. The table gives element and normalized x-ray count data for individual particles that were used as the “seed” particle defining the group. (Membership in a group was determined by comparison to these specific particle characteristics.) In the table, shaded elements are those not needed to account for at least 85% of the normalized x-ray counts.
E. Definition of Target Particle Types Sixty eight mutually exclusive Target Particle Types (TPTs) were defined by pooling and consolidation of particles represented in the Elemental Profile Groupings. Specific criteria for the TPTs were based on the qualitative presence of designated elements, and ranges and/or ratios in normalized x-ray counts for designated elements. These specific criteria are given in Appendix J. Criteria for Target Particle Type Classifications. Table 15 gives a descriptive summary of the TPTs.
10 2 For example, of the 81 values of the chi-square statistic, only four were below 23.6, the value for .005 with 9 df 11 See the Methods section for the steps used to define these classes and the Discussion section for explanation and discussion of the weaknesses. 푋
Page 33 of 76 This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 14. Example of Data in Appendix I: Carpet A Particles Defining Elemental Profile Groupings Occurring Above 1%*
Area 1 Area 2 Area 3 Group Size Four Elements with Corresponding Group Size Four Elements with Corresponding Group Size Four Elements with Corresponding Number Percent Highest X-Ray Counts Normalized Counts Number Percent Highest X-Ray Counts Normalized Counts Number Percent Highest X-Ray Counts Normalized Counts 197 6.6 S Ca Bi Hg 0.44 0.27 0.16 0.14 269 6.7 Ca Mg Al Zr 0.45 0.41 0.08 0.06 335 8.4 Al Si Mg Na 0.49 0.38 0.07 0.06 83 2.8 Ca Na Pb Hg 0.86 0.06 0.04 0.03 198 5.0 Ca Na Al Mg 0.47 0.41 0.07 0.05 128 3.2 Si Br S Cl 0.87 0.05 0.04 0.03 74 2.5 Al Si Mg Fe 0.47 0.45 0.05 0.03 140 3.5 S Na Bi Ca 0.41 0.32 0.16 0.10 98 2.5 Ca Mg Al Pb 0.47 0.44 0.06 0.03 68 2.3 Ca Na Mg Zn 0.83 0.09 0.05 0.02 127 3.2 Ca Na Al Hg 0.47 0.36 0.12 0.04 92 2.3 Ca Na Al W 0.79 0.08 0.08 0.05 46 1.5 Mg Ca Na Al 0.46 0.42 0.07 0.05 127 3.2 Na Ca Al Mg 0.56 0.27 0.11 0.06 91 2.3 Si Al Na W 0.51 0.29 0.16 0.05 43 1.4 S Ca Na Si 0.44 0.34 0.16 0.06 108 2.7 Si Al S Sr 0.69 0.24 0.04 0.03 90 2.3 Si Al WS 0.59 0.31 0.05 0.04 42 1.4 Si Al Sr S 0.61 0.26 0.08 0.05 87 2.2 Na Hg Zr W 0.50 0.19 0.18 0.13 80 2.0 Si Sr Br S 0.74 0.14 0.08 0.04 41 1.4 Ca S Na Pb 0.41 0.37 0.12 0.11 61 1.5 Ca Si Al Na 0.92 0.03 0.03 0.02 68 1.7 Si Al WS 0.70 0.19 0.07 0.04 35 1.2 Si Al Na Ca 0.37 0.32 0.17 0.14 53 1.3 Na Ca Hg Br 0.41 0.38 0.13 0.08 66 1.7 Si Sr S Cl 0.83 0.08 0.05 0.04 34 1.1 S Bi Ca Hg 0.39 0.27 0.22 0.12 53 1.3 S Na Hg Pb 0.38 0.32 0.17 0.14 60 1.5 Ca Mg Al Si 0.88 0.05 0.03 0.03 33 1.1 Si S Br Mg 0.83 0.06 0.06 0.05 52 1.3 Na Ca S Hg 0.43 0.39 0.09 0.09 57 1.4 Ca Na Bi S 0.73 0.12 0.10 0.04 32 1.1 Si Sr S Al 0.83 0.09 0.04 0.04 52 1.3 Na Ca S Al 0.54 0.23 0.13 0.10 56 1.4 Si Ca Mg Fe 0.48 0.21 0.19 0.12 31 1.0 Si Al Na Sr 0.52 0.20 0.14 0.14 52 1.3 S Na Bi Ca 0.45 0.24 0.22 0.09 49 1.2 Si Al Fe Mg 0.48 0.33 0.11 0.08 52 1.3 Na S Hg Bi 0.48 0.22 0.16 0.14 247 1. Al Si Na Mg 0.52 0.30 0.13 0.04 50 1.3 Ca Mg Na Al 0.41 0.41 0.13 0.05 45 1.1 S Ca Bi Hg 0.40 0.38 0.12 0.11 47 1.2 Na S Hg Pb 0.43 0.37 0.10 0.10 42 1.1 Na S Bi Ca 0.39 0.32 0.15 0.14 45 1.1 Na S Ca Al 0.50 0.29 0.14 0.08 45 1.1 Ca Mg Na S 0.42 0.28 0.23 0.08 43 1.1 Na Ca W Hg 0.41 0.36 0.13 0.10 43 1.1 Na Ca Mg Pb 0.55 0.34 0.06 0.05
*Shaded elements are those not needed to account for at least 85% of the normalized x-ray counts.
Page 34 of 42 This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 15. Descriptive Summary of Target Particle Types12
Normalized X-ray Count Restricted Type Designation Absence of X-Ray Counts of Ratios of Levels of P1 Al Al P2 Si Si P3 Si/Al Lower Si Al, Si Al, Si P4 Si/Al Medium Si Al, Si Al, Si P5 Si/Al Higher Si Al, Si Al, Si Fe, Mg, Na, P6 Al/Si/Ca Al, Ca, Si Al, Si S, Sr, W Fe, Mg, Na, P7 Si/Al/Ca Al, Ca, Si S, Sr, W P8 Al/Si/Fe Higher Fe Al, Fe, Si P9 Al/Si/Fe Lower Fe Al, Fe, Si Al, Si P10 Si/Al/Fe Lower Fe Al, Fe, Si Al, Si Ca, Fe, Na, P11 Si/Al/Mg Higher Mg Al, Mg, Si Al, Si S, Sr, W Ca, Fe, Na, P12 Si/Al/Mg Lower Mg Al, Mg, Si Al, Si S, Sr, W P13 Al/Si/Na Al, Na, Si Al, Si P14 Si/Al/Na Lower Si Al, Na, Si Al, Si Ca, Fe, Mg, P15 Si/Al/Na Higher Si Al, Na, Si Al, Si S, Sr, W P16 Al/Si Al, Si Al, Si Ca, Fe, Mg, P17 Al/Si/W Al, Si, W Al, Si Na, S, Sr P18 Si/Al/S Al, Si, S Al, Si P19 Si/Al/Sr Al, Si, Sr Al, Si P20 Si/Al/Ca/Na Al, Ca, Na, Si P21 Ca/Si/Mg Ca, Mg, Si Ca, Si P22 Si/Ca/Mg Ca, Mg, Si Ca, Si P23 Si/Mg Mg, Si Mg, Si P24 Si/Sr Si, Sr P25 Si/W Si, W P26 Ca Ca P27 Ca/Al Ca, Al P28 Ca/Bi Ca, Bi P29 Ca/Br Ca, Br P30 Ca/Fe/S Ca, Fe, Si Ca, Fe P31 Ca/Mg Higher Ca Ca, Mg P32 Ca/Mg Lower Ca Ca, Mg Ca, Mg
12 Full descriptions are given in Appendix H. Criteria for Target Particle Type Classifications.
Page 35 of 42 This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 16. Descriptive Summary of Target Particle Types (Continued)
Normalized X-ray Count Restricted Type Designation Absence of X-Ray Counts of Ratios of Levels of P33 Ca/Mg/Al Al, Ca, Mg Ca, Mg P34 Ca/Mg/Na Ca, Mg, Na Ca, Mg Al P35 Ca/Na Lower Ca Ca, Na Ca, Na P36 Ca/Na Medium Ca Ca, Na Ca, Na P37 Ca/Na Higher Ca Ca, Na Ca, Na P38 Na/Ca Ca, Na P39 Ca/Na/Al Higher Ca Al, Ca, Na E2, E313 P40 Ca/Na/Al Lower Ca Al, Ca, Na Ca, Na P41 Na/Ca/Al Al, Ca, Na Ca, Na P42 Ca/Na/Br Br, Ca, Na E2, E3 P43 Ca/Na/(Hg,W) Ca, Na, Hg, W Ca, Na Al P44 Na/Ca/Hg/Zr Ca, Hg, Na, Zr P45 Ca/Na/W Ca, Na, W E2, E3 P46 Ca/W Ca, W P47 Ba/S/Bi Ba, Bi, S Ba, S P48 Ba/S/Na Ba, Na, S Ba, S ; Na, S P49 Ca/Ba/S Ba, Ca, S Ba, Ca P50 Ca/S (no Pb, Bi) Ca, S Ca, S Bi, Pb P51 S/Ca/Bi/Hg Bi, Ca, Hg, S Ca, S P52 S/Ca/Bi/Au Au, Bi, Ca, S Ca, S P53 S/Ca/Bi Bi, Ca, S Ca, S Au, Hg P54 S/Ca/Pb/Hg Ca, Hg, Pb, S Ca, S P55 S/Ca/Pb/Au Au, Ca, Hg, Pb Ca, S P56 S/Ca/Pb Ca, Pb, S Ca, S Au, Bi, Hg P57 Na/Ca/S Ca, Na, S Ca, Na P58(1/2) Na/S/Ca/Bi Bi, Ca, Na, S E1, E2 P58(2/2) Na/S/Ca/Bi Bi, Ca, Na, S Na, S P59 Na/S/Hg Hg, Na, S Na, S Bi, Ca P60 Fe Fe P61 Fe/Al Al, Fe Al, Fe P62 Fe/Cr/Na Cr, Fe, Na Cr, Fe ; Cr, Na P63 Fe/Na Fe, Na Fe, Na P64 Fe/Al/Si Al, Fe, Si Al, Fe P65 Cl/Na/Ca Ca, Cl, Na Ca, Na ; Cl, Na P66 Cu/Cl/Ni Cl, Cu, Ni Cl, Ni ; Cu, Cl Ca, Hg, Mg, Na, P67 Hg,Mg,Na,W,Zr/Ca/Pb Pb, W, Zr P68 Ti/(Al,La,Na) Al, La, Na, Ti Ti, E2
13 E1, … E4 = Four elements with highest normalized x-ray counts in descending order Page 36 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
F. Occurrence of Target Particle Types for Carpets, Carpet Fibers and Process Blanks The incidences of Target Particle Types (TPTs) in each of the samples and process blanks are given in Appendix K. Incidence of Target Particle Types. Examples of the data format are given in Tables 17 and 18. Ranges in incidence in these tables, and throughout this report and its appendices, are highlighted as follows: dark gray (0 to 5), gray (6 to10), yellow (11 to 50), orange (51 to 200) and red (> 200).
Process Blanks showed non-negligible levels for some TPTs. This occurrence is “particle noise” associated with the methodology that must be considered when interpreting the levels of occurrence of TPTs in this project. Most of the TPTs occur very rarely in the Blanks. Table 19 shows those TPTs with an incidence of more than five particles in any process blank or with an estimated Limit of Detection (LOD) greater than five.14 Recurring high levels are present for seven of the TPTs (P2, P5, P15, P16, P24, P26, and P30). It is reasonable to omit these from further consideration.15 Only one or two occurrences of high levels are present for the other 17 TPTs, and their significance is best judged in the context of the levels observed in the samples themselves. Table 20 shows the number of samples with levels greater than the LOD and greater than twice the LOD for these 17 TPTs. Sixteen of the TPTs have many occurrences in the samples above the LOD, ranging from 15 (12.5% of samples) to 66 (55% of samples). It is reasonable to consider these going forward. One of the TPTs (P1) shows only five samples with occurrences above the LOD, and only one of these samples has a level above twice the LOD. It is reasonable to omit this Type from further consideration.
14 Mean plus 3 standard deviations using the one-tailed t-statistic. 15 Although there are levels present in some of the samples above the LOD for these TPTs, the LOD are based on statistical assumptions and practices that are only strictly applicable for well-established methods and processes. This is not the case for the present project, and it would be reckless to assume that levels of these particles in the samples represent a reliable “signal.” Page 37 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 17. Example of Data in Appendix K for Sets of ten Fibers from One Area16 Target Particle Types in Residential Carpets - Sets of ten Fibers from One Area
Target Particle Type Carpet A Carpet BH Carpet PH Broader Set of Carpets Type Description Area 1 Area 2 Area 3 Mean Area 1 Area 2 Area 3 Mean Area 1 Area 2 Area 3 Mean R1 R2 R3 R4 R5 R6 R7 P47 Ba/S/Bi 4 0 0 1 2 4 1 2 14 96 62 57 5 3 3 1 8 7 4 P48 Ba/S/Na 2 2 3 2 1 4 0 2 7 87 59 51 2 1 0 0 0 0 1 P49 Ca/Ba/S 0 0 0 0 0 0 0 0 18 5 15 13 0 0 0 0 0 0 0 P50 Ca/S (no Pb, Bi) 57 3 15 25 2 3 16 7 0 0 4 1 1 4 7 26 66 34 2 P51 S/Ca/Bi/Hg 130 29 51 70 6 6 65 26 1 3 4 3 24 20 43 113 314 132 25 P52 S/Ca/Bi/Au 64 15 29 36 4 5 42 17 1 0 3 1 22 5 16 90 198 79 10 P53 S/Ca/Bi 35 6 8 16 3 2 19 8 1 4 4 3 6 15 21 56 73 43 9 P54 S/Ca/Pb/Hg 38 5 13 19 2 8 30 13 1 3 2 2 4 5 10 29 78 28 6 P55 S/Ca/Pb/Au 17 4 9 10 0 4 17 7 0 0 1 0 1 0 2 12 35 12 0 P56 S/Ca/Pb 25 5 6 12 122205120058 21 7 1 P57 Na/Ca/S 0 115 26 47 001010420000000 P58 Na/S/Ca/Bi 175 383 119 226 129 37 25 64 13 9 33 18 83 5 855 15 96 88 345 P59 Na/S/Hg 19 167 18 68 9 19 10 13 1 4 27 11 8 0 19 0 2 1 4 P60 Fe 4 0 12 5 8 8 220 79 0 0 1 0 2 5 6 8 11 27 5 P61 Fe/Al 6 0 5 4 2 8 28 13 0 1 1 1 5 5 10 14 16 22 9 P62 Fe/Cr/Na 6 2 6 5 16 30 2 16 11320204010 P63 Fe/Na 35 2 27 21 26 36 401 154 1 4 8 4 7 7 13 6 16 30 6 P64 Fe/Al/Si 5 3 24 11 10 29 6 15 0 1 7 3 2 15 11 24 28 25 18 P65 Cl/Na/Ca 0 0 0 0 44 0 0 15 00000000000 P66 Cu/Cl/Ni 0000 000000000000000 P67 Hg,Mg,Na,W,Zr/Ca/Pb 1 6 9 5 497 373 174 348 1 2 5 3 0 1 2 2 49 28 140 P68 Ti/(Al,La,Na) 61 5 31 32 26 39 579 215 20 9 15 15 5 11 11 27 38 25 18 Total Particles 3001 4000 4000 3667 2948 4000 4000 3649 1363 4000 4000 3121 642 4000 4000 3206 4000 4000 4000 % as Target Types 0.57 0.50 0.61 0.56 0.52 0.50 0.54 0.52 0.51 0.62 0.55 0.561 0.56 0.52 0.64 0.69 0.58 0.63 0.46
dark gray 0 to 5 gray 6 to 10 yellow 11 to 50 gold 51 to 200 red > 200
16 See Appendix K. Incidence of Target Particle Types: Table K1 (3 of 3).
Page 38 of 42 This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 18. Example of Data in Appendix K for Sets of ten and Individual Fibers in One Carpet17 Target Particle Types in Residential Carpet PH - Sets of ten and Individual Fibers
Target Particle Type Area 1 Area 2 Area 3 Type Description 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 P26 Ca 202 9 9 20 463 21 30 487 325 26 51 82 P27 Ca/Al 29 1 2 0 251 3 12 295 163 2 22 21 P28 Ca/Bi 14 0 0 1 71 1 1 71 34 2 5 16 P29 Ca/Br 19 0 0 2 80 4 6 124 70 1 4 13 P30 Ca/Fe/S 1 1 0 2 2 0 2 55 49 56 52 92 P31 Ca/Mg Higher Ca 15 0 0 1 79 0 0 118 55 0 2 8 P32 Ca/Mg Lower Ca 21 1 1 0 60 1 2 63 67 1 3 10 P33 Ca/Mg/Al 0 0 0 0 8 0 0 21 16 0 0 2 P34 Ca/Mg/Na 2 0 0 0 17 0 0 7 28 1 0 2 P35 Ca/Na Lower Ca 39 0 0 4 107 1 0 85 103 5 8 11 P36 Ca/Na Medium Ca 40 0 1 3 185 2 10 208 152 2 6 18 P37 Ca/Na Higher Ca 81 0 3 7 383 10 13 463 286 9 22 31 P38 Na/Ca 000000000031 P39 Ca/Na/Al Higher Ca 20 0 0 0 150 1 4 139 66 6 7 15 P40 Ca/Na/Al Lower Ca 200031013102 P41 Na/Ca/Al 000000000000 P42 Ca/Na/Br 12 0 0 1 63 1 4 63 39 1 1 10 P43 Ca/Na/(Hg,W) 100060028003 P44 Na/Ca/Hg/Zr 100000002000 P45 Ca/Na/W 25 1 0 0 108 2 4 94 85 3 4 8 P46 Ca/W 31 1 4 2 175 3 4 207 114 7 15 15
dark gray 0 to 5 gray 6 to 10 yellow 11 to 50 gold 51 to 200 red > 200
17 See Appendix K. Incidence of Target Particle Types: Table K6 (2 of 3). Page 39 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 19. Target Particle Types with More than Five Particles in a Process Blank or an Estimated LOD Greater than Five Particles
Target Particle Type Sample Designation (Process Blanks) LOD Type Description B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 P1 Al 822112121000 8.1 P2 Si 2 5 5 12 3 2 1 23 13 1 2 0 26.3 P3 Si/Al Lower Si 0 12 2 2 0 0 0 2 0 0 2 0 11.8 P5 Si/Al Higher Si 1 3 0 10 4 1 0 27 14 0 5 0 29.8 P6 Al/Si/Ca 030410041012 6.0 P7 Si/Al/Ca 001200030005 5.8 P11 Si/Al/Mg Higher Mg 000600061000 8.0 P14 Si/Al/Na Lower Si 320500050000 7.3 P15 Si/Al/Na Higher Si 7 2 1 18 0 0 0 41 38 0 1 2 54.4 P16 Al/Si 2 7 1 35 4 2 1 50 9 11 1 0 57.6 P17 Al/Si/W 141000032100 5.0 P19 Si/Al/Sr 060011011021 6.1 P23 Si/Mg 004124001000 5.6 P24 Si/Sr 2 4 4 22 5 5 1 33 17 1 1 1 39.1 P25 Si/W 010010097100 10.8 P26 Ca 3 57 7 5 12 4 2 10 5 1 0 3 55.6 P27 Ca/Al 0 9 3 3 11 3 1 1 1 0 0 0 13.6 P30 Ca/Fe/S 15 14 0 16 75 64 15 3 0 0 1 0 93.7 P37 Ca/Na Higher Ca 0 11 0 1 1 5 0 3 1 1 0 0 11.6 P46 Ca/W 081122014000 8.6 P60 Fe 001151042000 6.3 P61 Fe/Al 000105012001 5.2 P62 Fe/Cr/Na 0 1 2 2 1 14 8 4 1 0 0 5 15.7 P63 Fe/Na 123151121000 5.7
dark gray 0 to 5 gray 6 to 10 yellow 11 to 50 gold 51 to 200 red > 200
Page 40 of 42 This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 20. Number of Sample Occurrences Above LOD for 27 Target Particle Types with One or Two High Levels of Occurrence in Process Blanks
Target Particle Type Number of Samples Type Description LOD > LOD >2 LOD P1 Al 8.1 5 1 P62 Fe/Cr/Na 15.7 15 9 P23 Si/Mg 5.6 25 8 P61 Fe/Al 5.2 27 14 P11 Si/Al/Mg Higher Mg 8.0 28 15 P60 Fe 6.3 28 8 P25 Si/W 10.8 39 19 P46 Ca/W 8.6 42 25 P27 Ca/Al 13.6 43 27 P37 Ca/Na Higher Ca 11.6 46 26 P6 Al/Si/Ca 6.0 47 33 P19 Si/Al/Sr 6.1 50 34 P63 Fe/Na 5.7 53 26 P14 Si/Al/Na Lower Si 7.3 55 39 P17 Al/Si/W 5.0 56 44 P3 Si/Al Lower Si 11.8 58 37 P7 Si/Al/Ca 5.8 66 40
dark gray 0 to 5 gray 6 to 10 yellow 11 to 50 gold 51 to 200 red > 200
Page 41 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
G. Variation Among Different Areas of the Same Carpet In this section and those that follow, some Target Particle Types (TPTs) have been omitted and others consolidated. Omitted types follow the rationale given in the previous section, with one additional omission: type P41, which had no occurrences. Five TPT consolidations were made for two or more closely related classifications that were found to occur with similar relative proportions in the samples. Table 21 shows these consolidations. The resulting 47 TPTs are conveniently considered in five chemical groups, as shown in Table 22: siliceous (P3 to P25), calcareous (P27 to P46), sulfurous (P47 to P59, ferrous (P60 to P64) and other (P65 to P68).
Table 21. Consolidations of Closely Related Target Particle Type Classifications that Occur with Similar Relative Proportions in the Samples18
Target Particle Types Consolidated Original Type Description Type Description P6* Si/Al/Ca P6 Si/Al/Ca P7 Al/Si/Ca P8* Si/Al/Fe P8 Al/Si/Fe Higher Fe P9 Al/Si/Fe Lower Fe P10 Si/Al/Fe Lower Fe P31* Ca/Mg P31 Ca/Mg Higher Ca P32 Ca/Mg Lower Ca P35* Ca/Na P35 Ca/Na Lower Ca P36 Ca/Na Medium Ca P37 Ca/Na Higher Ca P50* Ca/S P50 Ca/S (no Pb, Bi) P51 S/Ca/Bi/Hg P52 S/Ca/Bi/Au P53 S/Ca/Bi P54 S/Ca/Pb/Hg P55 S/Ca/Pb/Au P56 S/Ca/Pb
18 Unconsolidated data can be found in Appendix K. Incidence of Target Particle Types. Page 42 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 23 shows results for three areas of Carpet A, which illustrate trends seen in the carpet area results. There are both notable similarities and notable differences. A linear, proportional distribution of a uniform fine particle population can be quickly dismissed. Under such a model we would expect each of the particle types to occur in proportions of 3:4:4 (given the respective total particle numbers of 3001, 4000 and 4000). Consideration of TPT P3 is sufficient: the levels of occurrence for Areas 1 and 2 are comparable (though off in proportion), but Area 3 has more than three times the particles. TPTs P4 and P20 show alternative trends which are also divergent from linear proportions based on the total particle count.
Table 22. Five Convenient Chemical Groupings of the Target Particle Types
Siliceous Group Calcareous Group Sulfurous Group Type Description Type Description Type Description P3 Si/Al Lower Si P27 Ca/Al P47 Ba/S/Bi P4 Si/Al Higher Si P28 Ca/Bi P48 Ba/S/Na P6* Si/Al/Ca P29 Ca/Br P49 Ca/Ba/S P8* Si/Al/Fe P31* Ca/Mg P50* Ca/S P11 Si/Al/Mg Higher Mg P33 Ca/Mg/Al P57 Na/Ca/S P12 Si/Al/Mg Lower Mg P34 Ca/Mg/Na P58 Na/S/Ca/Bi P13 Al/Si/Na P35* Ca/Na P59 Na/S/Hg P14 Si/Al/Na Lower Si P38 Na/Ca Ferrous Group P17 Al/Si/W P39 Ca/Na/Al Higher Ca P60 Fe P18 Si/Al/S P40 Ca/Na/Al Lower Ca P61 Fe/Al P19 Si/Al/Sr P42 Ca/Na/Br P62 Fe/Cr/Na P20 Si/Al/Ca/Na P43 Ca/Na/(Hg,W) P63 Fe/Na P21 Ca/Si/Mg P44 Na/Ca/Hg/Zr P64 Fe/Al/Si P22 Si/Ca/Mg P45 Ca/Na/W Other Group P23 Si/Mg P46 Ca/W P65 Cl/Na/Ca P25 Si/W P66 Cu/Cl/Ni P67 Hg,Mg,Na,W,Zr/Ca/Pb P68 Ti/(Al,La,Na)
Page 43 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 23. Carpet A Target Particle Type Occurrences: ten Fibers from Each of Three Areas
Carpet A Area 1 Area 2 Area 3 Total Particles 3001 4000 4000
Carpet A: Siliceous Area 1 Area 2 Area 3 Carpet A: Calcareous Area 1 Area 2 Area 3 Carpet A: Sulfurous Area 1 Area 2 Area 3 P3 Si/Al Lower Si 44 34 148 P27 Ca/Al 46 27 55 P47 Ba/S/Bi 4 0 0 P4 Si/Al Medium Si 15 82 48 P28 Ca/Bi 7 4 7 P48 Ba/S/Na 2 2 3 P6* Si/Al/Ca 32 17 71 P29 Ca/Br 5 2 9 P49 Ca/Ba/S 0 0 0 P8* Si/Al/Fe 28 8 114 P31* Ca/Mg 51 260 108 P50* Ca/S 366 67 131 P11 Si/Al/Mg Higher Mg 11 2 51 P33 Ca/Mg/Al 20 52 29 P57 Na/Ca/S 0 115 26 P12 Si/Al/Mg Lower Mg 23 8 61 P34 Ca/Mg/Na 13 111 15 P58 Na/S/Ca/Bi 175 383 119 P13 Al/Si/Na 40 28 100 P35* Ca/Na 145 56 129 P59 Na/S/Hg 19 167 18 P14 Si/Al/Na Lower Si 65 25 121 P38 Na/Ca 0 91 2 P17 Al/Si/W 30 3 47 P39 Ca/Na/Al Higher Ca 31 8 27 Carpet A: Ferrous Area 1 Area 2 Area 3 P18 Si/Al/S 1 0 11 P40 Ca/Na/Al Lower Ca 2 143 20 P60 Fe 4 0 12 P19 Si/Al/Sr 44 30 74 P42 Ca/Na/Br 6 1 2 P61 Fe/Al 6 0 5 P20 Si/Al/Ca/Na 15 4 39 P43 Ca/Na/(Hg,W) 1 36 6 P62 Fe/Cr/Na 6 2 6 P21 Ca/Si/Mg 1 13 3 P44 Na/Ca/Hg/Zr 0 8 1 P63 Fe/Na 35 2 27 P22 Si/Ca/Mg 15 10 64 P45 Ca/Na/W 22 5 9 P64 Fe/Al/Si 5 3 24 P23 Si/Mg 20 12 10 P46 Ca/W 28 11 15 P25 Si/W 11 3 26 Carpet A: Other Area 1 Area 2 Area 3 P65 Cl/Na/Ca 0 0 0 P66 Cu/Cl/Ni 0 0 0 P67 Hg,Mg,Na,W,Zr/Ca/Pb 1 6 9 P68 Ti/(Al,La,Na) 61 5 31
dark gray 0 to 5 gray 6 to 10 yellow 11 to 50 gold 51 to 200 red > 200
Page 44 of 42 This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Another possibility is that the relative proportions of the TPTs in each of the areas will be consistent. This is found for some types and not for others. Among the siliceous TPTs in Carpet A, for example, P6*, P13, P14 and P19 share a proportional relationship that is persuasive: Area 1 ranges from 40 to 60% of Area 3, while Area 2 ranges from 20 to 40%. A quick glance around the table shows that this is not a consistent trend: proportions vary widely among the three carpet areas.
Qualitative similarities among the areas are more abundant, notably the very low quantities of 11 of the TPTs (calcareous: P28, P29, P42, P44; sulfurous: P47, P48, P49; ferrous: P61, P62; other: P65, P66, P67). These, combined with the proportionality of the four siliceous TPTs (P6*, P13, P14, P19) are points of similarity.
Differences among the three carpet areas are also present, but they show trends. For many TPTs where Area 2 has its highest levels of occurrence, Areas 1 and 3 are low (calcareous: P34, P38, P40, P43; sulfurous: P57, 59). For TPTs with high incidence in Area 2, Areas 1 and 3 have levels ranging up to half that of Area 2 low (calcareous: P31*, P33; sulfurous: P58). Though not as striking, there are TPTs where Areas 1 and 3 have higher levels, with very low levels in Area 2 (siliceous: P8*, P11, P12, P17, P20, P25; calcareous: P35; ferrous: P63; other: P68). Overall, Area 1 and Area 3 are much closer, both qualitatively and with similar proportionality.
Table 24 shows results for siliceous TPTs from three different areas of three of the carpets. Carpet BH shows a consistent (though unequal, and non-proportional) relationship among the particle occurrences. Almost all siliceous TPTs in Carpet BH Area 2 show two to several-fold higher occurrences, with comparable levels for Areas 1 and 3. There is also good qualitative agreement among low occurrences across all three areas. Carpet PH shows very low occurrences of siliceous TPTs for two areas, contrasting markedly with the third area. Areas 1 and 2 of Carpet PV are remarkably similar for all 16 siliceous TPTs, while Area 3 shows much lower occurrences (along with a lower overall particle recovery).
Table 25 shows results for calcareous TPTs from three different areas of three of the carpets.19 Carpet BH again shows a consistent (though unequal, and non-proportional) relationship among the particle occurrences. For the four most frequently occurring TPTs (P27, P31*, P33, P35*) Areas 1 and 2 have comparable levels (within about 30%), while Area 3 is consistently some 30 to 60% lower. Notably, this differs from the trend seen in the siliceous TPTs (higher Area 2 occurrences, with comparable occurrences for Areas 1 and 3). Four other TPTs, however, do show the siliceous TPT trend (P38, P39, P40, P45). Carpet PH, which showed nearly no siliceous TPTs for Areas 1 and 2, shows consistent relative proportions in calcareous TPT occurrences with Area 2 > Area 3 >> Area 1 for the nine most frequently occurring calcareous TPTs. Carpet BV shows negligibly low occurrences for most calcareous TPTs, and concurrence among the three areas for the four TPTs occurring at higher (though still low) levels (P27, P31*, P35* and P46).
19 Two of these, BH and PH are the same carpets as shown in Table 24, one (BV), is not. These are examples of the data; full data are present in Appendix K. Incidence of Target Particle Types.
Page 45 of 42 This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 24. Siliceous Particle Types from Different Areas of Carpets BH, PH and PV Carpet BH Carpet PH Carpet PV Area Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Total Particles 2948 4000 4000 1363 4000 4000 4000 4000 1005 P3 Si/Al Lower Si 29 86 22 8 1 16 172 142 22 P4 Si/Al Medium Si 28 47 18 0 0 0 28 14 5 P6* Si/Al/Ca 13 26 12 6 3 11 77 132 32 P8* Si/Al/Fe 11 35 10 0 0 20 125 170 32 P11 Si/Al/Mg Higher Mg 4 10 5 0 1 7 26 21 12 P12 Si/Al/Mg Lower Mg 16 27 6 1 1 6 63 69 9 P13 Al/Si/Na 9 44 4 2 4 13 163 73 12 P14 Si/Al/Na Lower Si 15 62 7 1 3 18 199 98 19 P17 Al/Si/W 18 93 15 11 6 46 233 224 33 P18 Si/Al/S 2 2 3 0 0 1 6 11 5 P19 Si/Al/Sr 17 35 11 1 2 11 118 100 13 P20 Si/Al/Ca/Na 1 7 1 5 2 7 20 13 1 P21 Ca/Si/Mg 5 16 8 0 0 3 1 5 14 P22 Si/Ca/Mg 8 29 4 1 0 9 34 54 12 P23 Si/Mg 0 6 0 4 0 0 2 0 4 P25 Si/W 9 32 6 3 4 28 64 35 7
Table 25. Calcareous Particle Types from Different Areas of Carpets BH, PH and BV
Carpet BH Carpet PH Carpet BV Area Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Total Particles 2948 4000 4000 1363 4000 4000 1233 3613 1431 P27 Ca/Al 51 47 29 29 251 163 23 19 23 P28 Ca/Bi 11 8 9 14 71 34 4 6 1 P29 Ca/Br 10 15 6 19 80 70 6 6 2 P31* Ca/Mg 126 124 85 36 139 122 22 13 15 P33 Ca/Mg/Al 33 45 18 0 8 16 2 5 1 P34 Ca/Mg/Na 9 10 11 2 17 28 0 3 1 P35* Ca/Na 73 100 34 160 675 541 26 27 9 P38 Na/Ca 2 17 4 0 0 0 0 0 0 P39 Ca/Na/Al Higher Ca 7 22 4 20 150 66 3 3 2 P40 Ca/Na/Al Lower Ca 7 29 5 2 3 3 0 0 1 P42 Ca/Na/Br 7 6 1 12 63 39 1 1 0 P43 Ca/Na/(Hg,W) 0 4 2 1 6 8 0 0 0 P44 Na/Ca/Hg/Zr 3 15 11 1 0 2 1 0 0 P45 Ca/Na/W 8 26 4 25 108 85 1 2 1 P46 Ca/W 33 37 28 31 175 114 11 10 7
Page 46 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 26 shows results for sulfurous, ferrous and other TPTs from three different areas of three of the carpets. Carpet BH is again included. These TPT occurrences show none of the trend seen for the siliceous particles (highest occurrence in Area 2, with comparable levels for Areas 1 and 3), and only one TPT (P67) shows the trend seen for calcareous particles (comparable Area 1 and 2, with lower Area 3). There is also a new “trend”: much higher levels in Area 3 (for the TPTs with the four highest levels: P50*, P60, P63 and P68). As with the siliceous and calcareous TPTs, Carpet BH shows good qualitative agreement for low occurrences across all three areas. Carpet PL results are noteworthy for the high levels of one TPT (P50*), whose relative magnitude across the three areas follows the order, though not the proportion, of the total particle counts. Some other TPTs in these groups occur at lower levels in both Areas 2 and 3 (P58, P60, P63, P64 and P68). Carpet F, which has low total particle counts overall, shows very low occurrences for all of the TPTs, with the exception of Area 2, which shows one TPT at a high level (P66) and one at a low level (P63).
The trends illustrated in these examples continue throughout the dataset in Appendix K. For some carpets, and some TPTs, occurrences are highly localized: present in only one of three carpet areas sampled, or present in grossly different amounts among the three areas.20 This occurred regularly. Among the 47 TPTs used, and the nine carpets, 55 clear instances were observed (13.0%). For many other TPTs, in these same carpets, comparable occurrences were much more frequently observed, some of which showed a regular ranking following the total number of particles. Comparable occurrences across the three carpet three areas were observed in 176 clear instances (41.6%).21 Comparable absences also occurred frequently, with some 141 instances (33.3%).22 Overall, comparable results across the three carpet areas occurred approximately 75% of the time.
20 Grossly different is taken here as a difference of greater than an order of magnitude, after normalizing the occurrence frequencies to a total particle count of 4000 (the maximum number analyzed as set by computer-assisted SEM/EDS parameters). See Appendix K. Incidence of Target Particle Types, Table K3A for the normalized frequencies. 21 Comparable occurrences (in frequencies per 4000) were taken as those where the minimum of the three area values and the maximum differed by less than a factor of 5. 22 Comparable absences (in frequencies per 4000) were taken as those where all three areas had frequencies of 10 or less. Page 47 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 26. Sulfurous, Ferrous and Other Particle Types from Different Areas of Carpets BH, PL and F. Carpet BH Carpet PL Carpet F Area Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Area 1 Area 2 Area 3 Total Particles 2948 4000 4000 4000 2169 3662 445 1179 359 P47 Ba/S/Bi 2 4 1 0 0 2 1 2 2 P48 Ba/S/Na 1 4 0 0 1 0 0 0 1 P49 Ca/Ba/S 0 0 0 0 0 0 0 0 0 P50* Ca/S 18 30 191 2797 310 931 3 5 4
Sulfurous P57 Na/Ca/S 0 0 1 0 0 0 0 0 0 P58 Na/S/Ca/Bi 129 37 25 8 22 18 0 1 2 P59 Na/S/Hg 9 19 10 0 2 0 0 0 0
P60 Fe 8 8 220 1 11 13 1 10 8 P61 Fe/Al 2 8 28 0 8 8 3 8 3 P62 Fe/Cr/Na 16 30 2 5 8 1 2 2 1
Ferrous P63 Fe/Na 26 36 401 4 14 23 6 16 4 P64 Fe/Al/Si 10 29 6 2 10 18 0 3 0
P65 Cl/Na/Ca 44 0 0 0 0 0 0 0 0 P66 Cu/Cl/Ni 0 0 0 0 0 0 2 136 0
Other P67 Hg,Mg,Na,W,Zr/Ca/Pb 497 373 174 2 1 3 3 2 1 P68 Ti/(Al,La,Na) 26 39 579 3 15 12 2 10 3 dark gray 0 to 5 gray 6 to 10 yellow 11 to 50 gold 51 to 200 red > 200
Page 48 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
H. Variation Within Single Carpet Areas Within-carpet variation was tested using TPT occurrences for three individual carpet fibers from each of three carpet areas in nine carpets. Tables 27 to 29 illustrate trends in the results, using selected TPT occurrences for six of the carpets.23
Table 27 shows selected results for residential Carpet A and residential Carpet BH, featuring calcareous, sulfurous, ferrous and other TPTs. For Carpet A some individual fibers from Areas 1 and 3 show very low particle totals, with values for total particles of 67, 85, 161 and 164. Area 2 makes a striking contrast with ten-fold higher values. For Area 2 almost all TPTs found in the 10-Set are seen well above the LOD in the single fibers, and most of the levels in the single fibers follow the ranking of the total particle values: > Fiber 3 > Fiber 2 > Fiber 1. Two of the Carpet A fibers, with particle numbers in the 300-500 range, show occurrences near the LOD that closely follow the 10-Sets: Fiber 3 in Area 1 and Fiber 2 in Area 3.
For Carpet BH in Table 27, Area 3 shows one fiber (Fiber 1) with abundant total particles (4000, the maximum measured) and two others with 504 and 234 total particles. Four of the TPTs for this area (P60, P61, P63 and P67) show a reasonable proportionality following these total particle numbers. In contrast, another particle type (P68) shows exceptionally high levels in both the Area 3 10-Set and in Fiber 1, but has no occurrence in Fibers 2 and 3. Similarly, in Areas 1 and 2, TPT P67 shows high levels in the 10-Sets, while individual fibers show low or insignificant levels. For TPT P62 four of the individual fibers (with low overall particle numbers) show higher occurrences for TPTs than do their corresponding 10-Sets (Area 1, Fibers 2, 3; Area 4, Fibers 1, 3).
Table 28 shows selected results for residential Carpet PH and workplace Carpet PV, featuring calcareous and sulfurous TPTs. For Carpet PH (as with Carpet A in Table 27) some individual fibers from Areas 1 and 2 show very low particle totals. The two fibers with particle totals below 100 (Area 1, Fibers 1, 2) show insignificant levels of the TPTs. With the somewhat higher particle totals, occurrences are consistently seen in the individual fibers for those TPTs showing the highest levels in the Area 10-Sets.24 With the still higher individual fiber particle total seen in Area 3, Fiber 3, levels are seen for the five highest TPTs occurring in the Area 10-Set. For the highest individual fiber total particle level (4000, seen in Area 2, Fiber 3) the TPT occurrences closely follow those seen in the 10-Set.
For Carpet PL there is a single TPT (P50*) that occurs at high to very high levels in all three Area 10-Sets. This is seen in all individual fibers whose total particle numbers are 375 or above.
Table 29 shows selected results for vehicular Carpet PV and workplace Carpet W, featuring siliceous TPTs. Carpet PV, Area 2 shows high total particle levels for each of the three individual fibers, and the levels of the TPTs seen are very close to those in the Area 10-Set. For Area 3, the total particle levels are lower for both the 10-Set (1005) and the individual fibers. Fiber 3, with only 330 total particles, shows insignificant levels of TPT occurrence, while Fibers 1 and 2, with 2 to 3 times this number, show levels in reasonably close agreement with the
23 Appendix K. Incidence of Target Particle Types contains the full set of data. 24 Specifically, (1) Particle Type P35* levels for Area 1, Fiber 3; Area 2, Fibers 1, 2; Area 3, Fibers 1, 2, and (2) Particle Type P27 levels for Area 2, Fiber 2 and Area 3, Fiber 2. Page 49 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
10-Set. Area 1 shows a 10-Set with the maximum total particle count and individual fibers in the 400 to 800 range. TPT occurrences are very low for the individual fibers, although the particle type occurring at the highest level in the 10-Set (P17) also shows the highest occurrence in the three individual fibers. Fiber 3 shows similar occurrences for TPTs P3, P12 and P25, but lacks other occurrences that would be expected if the effect were proportional (e.g. higher levels for P8*, P13 and P14).
Each of the Areas for Carpet W show lower TPT occurrences for individual fibers, ranging from 150 to 535. Area 3 also shows low values for the fiber 10-Set. Even so, Fiber 1 shows levels above the LOD for TPT P6*, the type with the highest level of occurrence in the Area 3 10-Set. Fiber 2 from Area 1 shows the same, as do Fibers 2 and 3 from Area 2. These fibers from Area 2 also show levels above the LOD for TPT P3, the type with the second highest level of occurrence in the Area 2 10-Set.
Fourteen individual fibers had total particle counts greater than 1000. The TPT occurrences for these fibers are shown in Tables 30 and 31, together with the results for the corresponding carpet areas. With few exceptions, the TPT occurrences from these fibers closely follow those from their originating area. The patterns of TPTs are highly characteristic and show both qualitative similarity and similarities in rank and proportion.. Ten of the fibers show a very close correspondence. Three show differences in one TPT25 and one shows a number of differences in the concentrations of calcareous TPTs.26
25 High levels of P62 for Carpet BV, Area 1, Fiber 2 and for Carpet PV, Area 2, Fiber 3. High levels of P67 for Carpet BV, Area 2, which are not seen in the fibers. 26 Higher levels of approximately half of the calcareous particles are seen in Carpet PH, Area 3 compared to Carpet PH, Area 3, Fiber 3. Page 50 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 27. Within-Carpet Area Results for Selected Target Particle Types from Residential Carpets A and BH
Area 1 Area 2 Area 3 Carpet A 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 Total Particles 3001 164 161 490 4000 872 1110 1782 4000 67 306 85 P31* Ca/Mg 51 1 0 1 260 62 64 80 108 0 10 1 P33 Ca/Mg/Al 20 1 0 2 52 27 22 22 29 0 2 2 P34 Ca/Mg/Na 13 1 0 1 111 8 33 48 15 0 2 0
Calcareous P35* Ca/Na 145 4 2 6 56 12 27 27 129 2 10 3 P50* Ca/S 366 9 1 12 67 28 24 130 131 1 7 0 P57 Na/Ca/S 0 0 0 0 115 15 37 40 26 0 3 2 P58 Na/S/Ca/Bi 175 5 1 11 383 37 70 119 119 1 16 3 Sulfurous P59 Na/S/Hg 19 0 0 2 167 12 18 60 18 1 9 0
Area 1 Area 2 Area 3 Carpet BH 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 Total Particles 2948 244 345 239 4000 421 312 691 4000 4000 504 234 P60 Fe 8 0 2 1 8 1 0 4 220 165 30 7 P61 Fe/Al 2 1 0 3 8 4 1 2 28 21 5 0 P62 Fe/Cr/Na 16 13 76 47 30 42 9 87 2 7 8 23
Ferrous P63 Fe/Na 26 2 3 1 36 6 1 8 401 233 22 16 P64 Fe/Al/Si 10 0 0 0 29 2 1 2 6 6 0 1 P65 Cl/Na/Ca 44 00000000000 P66 Cu/Cl/Ni 000000000000
Other P67 Hg,Mg,Na,W,Zr/Ca/Pb 497 10 25 3 373 2 7 2 174 94 28 4 P68 Ti/(Al,La,Na) 26 3 2 1 39 4 0 0 579 1020 0 0
dark gray 0 to 5 gray 6 to 10 yellow 11 to 50 gold 51 to 200 red > 200
Page 51 of 42 This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 28. Within-Carpet Area Results for Selected Target Particle Types from Residential Carpet PH and Workplace Carpet PL
Area 1 Area 2 Area 3 Carpet PH 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 Total Particles 1363 70 59 205 4000 137 147 4000 4000 504 711 1568 P27 Ca/Al 29 1 2 0 251 3 12 295 163 2 22 21 P28 Ca/Bi 14 0 0 1 71 1 1 71 34 2 5 16 P29 Ca/Br 19 0 0 2 80 4 6 124 70 1 4 13 P31* Ca/Mg 36 1 1 1 139 1 2 181 122 1 5 18 P33 Ca/Mg/Al 0 0 0 0 8 0 0 21 16 0 0 2 Calcareous P34 Ca/Mg/Na 2 0 0 0 17 0 0 7 28 1 0 2 P35* Ca/Na 160 0 4 14 675 13 23 756 541 16 36 60
Area 1 Area 2 Area 3 Carpet PL 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 Total Particles 4000 1492 1742 848 2169 505 494 518 3662 375 692 454 P47 Ba/S/Bi 000000002000 P48 Ba/S/Na 000010010110 P49 Ca/Ba/S 000000000000 P50* Ca/S 2797 746 633 243 310 22 31 15 931 50 25 79
Sulfurous P57 Na/Ca/S 000000000000 P58 Na/S/Ca/Bi 8 6 3 0 22 1 2 1 18 1 4 0 P59 Na/S/Hg 010021000000
dark gray 0 to 5 gray 6 to 10 yellow 11 to 50 gold 51 to 200 red > 200
Page 52 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 29. Within-Carpet Area Results for Selected Target Particle Types from Vehicular Carpet PV and Workplace Carpet W
Area 1 Area 2 Area 3 Carpet PV 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 Total Particles 4000 809 438 604 4000 4000 4000 3779 1005 674 950 330 P3 Si/Al Lower Si 172 3 3 16 142 93 119 122 22 27 17 5 P4 Si/Al Medium Si 28 1 0 2 14 13 19 18 5 5 1 0 P6* Si/Al/Ca 77 4 6 7 132 97 101 96 32 11 7 7 P8* Si/Al/Fe 125 4 1 7 170 71 155 131 32 31 19 1 P11 Si/Al/Mg Higher Mg 26 3 0 1 21 21 24 21 12 3 3 0
Siliceous P12 Si/Al/Mg Lower Mg 63 2 2 11 69 40 41 61 9 5 14 1 P13 Al/Si/Na 163 5 3 5 73 98 65 89 12 16 10 4 P14 Si/Al/Na Lower Si 199 9 8 10 98 111 119 94 19 18 13 3 P17 Al/Si/W 233 11 8 25 224 168 137 154 33 26 22 4
Area 1 Area 2 Area 3 Carpet W 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 Total Particles 2896 514 464 535 4000 419 367 280 710 320 258 152 P3 Si/Al Lower Si 67 4 11 4 203 8 15 4 25 8 6 3 P4 Si/Al Medium Si 9 1 4 2 19 1 1 0 3 1 2 0 P6* Si/Al/Ca 143 7 15 9 291 49 41 8 71 8 2 4 P8* Si/Al/Fe 35 4 3 2 125 5 6 0 11 3 0 0 P11 Si/Al/Mg Higher Mg 15 0 5 2 35 1 4 1 2 0 1 0
Siliceous P12 Si/Al/Mg Lower Mg 20 0 2 0 80 4 2 1 11 0 1 0 P13 Al/Si/Na 91 59270101000 P14 Si/Al/Na Lower Si 117 7 12 11 62 3 0 4 8 2 1 0 P17 Al/Si/W 34 1 4 2 60 2 4 0 4 1 1 1
dark gray 0 to 5 gray 6 to 10 yellow 11 to 50 gold 51 to 200 red > 200
Page 53 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 30. Within-Carpet Area Results: Fibers with More Than 1000 Particles (1 of 2)
Carpet A Carpet BH Carpet PH Carpet PH Carpet BV Target Particle Type Area 2 Area 3 Area 2 Area 3 Area 1 Type Description 10-Set Fiber 2 Fiber 3 10-Set Fiber 1 10-Set Fiber 3 10-Set Fiber 3 10-Set Fiber 2 P3 Si/Al Lower Si 34 18 28 22 14 1 1 16 27 65 14 P4 Si/Al Medium Si 82 33 26 18 18 0 2 0 2 13 4 P6* Si/Al/Ca 17 10 6 12 7 3 0 11 17 51 21 P8* Si/Al/Fe 8 7 12 10 11 0 1 20 11 15 7 P11 Si/Al/Mg Higher Mg 23551107265 P12 Si/Al/Mg Lower Mg 8 4 0 6 5 1 0 6 4 11 10 P13 Al/Si/Na 28 14 13 4 17 4 2 13 13 5 4 P14 Si/Al/Na Lower Si 25 8 21 7 20 3 3 18 16 24 14 P17 Al/Si/W 3 2 1 15 23 6 10 46 27 37 20 P18 Si/Al/S 0 3 0 3 2 0 0 1 3 26 6 P19 Si/Al/Sr 30 12 21 11 11 2 1 11 8 23 10 P20 Si/Al/Ca/Na 45814207222 P21 Ca/Si/Mg 13 3 4 8 5 0 3 3 2 0 1 P22 Si/Ca/Mg 10 3 1 4 9 0 1 9 5 16 6 P23 Si/Mg 12 1 2 0 0 0 0 0 6 3 1 P25 Si/W 3 2 2 6 8 4 1 28 10 14 13 P27 Ca/Al 27 7 12 29 22 251 295 163 21 23 7 P28 Ca/Bi 4 0 0 9 5 71 71 34 16 4 3 P29 Ca/Br 2 1 1 6 3 80 124 70 13 6 4 P31* Ca/Mg 260 64 80 85 53 139 181 122 18 22 8 P33 Ca/Mg/Al 52 22 22 18 22 8 21 16 2 2 3 P34 Ca/Mg/Na 111 33 48 11 3 17 7 28 2 0 0 P35* Ca/Na 56 27 27 34 29 675 756 541 60 26 18 P38 Na/Ca 91 11 34 4 2 0 0 0 1 0 0 P39 Ca/Na/Al Higher Ca 8 1 3 4 4 150 139 66 15 3 1 P40 Ca/Na/Al Lower Ca 143 23 59 5 6 3 1 3 2 0 0 P42 Ca/Na/Br 1 0 0 1 1 63 63 39 10 1 1 P43 Ca/Na/(Hg,W) 36 11 21 2 1 6 2 8 3 0 0 P44 Na/Ca/Hg/Zr 8 0 0 11 4 0 0 2 0 1 0 P45 Ca/Na/W 5 2 0 4 6 108 94 85 8 1 1 P46 Ca/W 11 5 6 28 10 175 207 114 15 11 12 P47 Ba/S/Bi 0 0 0 1 1 96 66 62 3 1 1 P48 Ba/S/Na 2 0 0 0 0 87 45 59 5 0 0 P49 Ca/Ba/S 0 0 0 0 0 5 5 15 2 0 0 P50* Ca/S 67 24 130 191 94 15 0 19 18 13 6 P57 Na/Ca/S 115 37 40 1 0 0 1 4 0 0 0 P58 Na/S/Ca/Bi 383 70 119 25 10 9 2 33 14 1 1 P59 Na/S/Hg 167 18 60 10 9 4 0 27 0 0 0 P60 Fe 0 0 0 220 165 0 0 1 2 2 7 P61 Fe/Al 0 0 1 28 21 1 0 1 1 3 2 P62 Fe/Cr/Na 2 0 2 2 7 1 2 3 2 2 171 P63 Fe/Na 2 13 2 401 233 4 1 8 7 3 0 P64 Fe/Al/Si 31066107373 P65 Cl/Na/Ca 00000000000 P66 Cu/Cl/Ni 00000000000 P67 Hg,Mg,Na,W,Zr/Ca/Pb 6 1 3 174 94 2 1 5 1 3 0 P68 Ti/(Al,La,Na) 5 1 1 579 1020 9 2 15 47 3 4 Total Particles 4000 1110 1782 4000 4000 4000 4000 4000 1568 1233 1107
Page 54 of 42 This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 31. Within-Carpet Area Results: Fibers with More Than 1000 Particles (2 of 2)
Carpet BV Carpet PV Carpet PL Target Particle Type Area 2 Area 2 Area 1 Type Description 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 Fiber 3 10-Set Fiber 1 Fiber 2 P3 Si/Al Lower Si 70 22 15 24 142 93 119 122 19 7 15 P4 Si/Al Medium Si 26 16 7 12 14 13 19 18 5 2 8 P6* Si/Al/Ca 100 24 51 43 132 97 101 96 33 7 42 P8* Si/Al/Fe 35 9 13 7 170 71 155 131 10 1 3 P11 Si/Al/Mg Higher Mg 56 59 63 54 21 21 24 21 7 3 6 P12 Si/Al/Mg Lower Mg 24 6 3 14 69 40 41 61 5 2 9 P13 Al/Si/Na 21 23 8 7 73 98 65 89 6 6 7 P14 Si/Al/Na Lower Si 48 21 13 15 98 111 119 94 15 4 15 P17 Al/Si/W 53 10 22 22 224 168 137 154 16 4 17 P18 Si/Al/S 13 1 0 3 11 6 12 6 4 2 1 P19 Si/Al/Sr 35 13 11 11 100 72 69 80 8 3 9 P20 Si/Al/Ca/Na 6 1 7 0 13 19 15 18 1 1 0 P21 Ca/Si/Mg 33425454301 P22 Si/Ca/Mg 16 1 6 8 54 33 47 45 12 0 1 P23 Si/Mg 5 1 0 3 0 4 3 18 3 3 3 P25 Si/W 69 26 33 46 35 48 34 22 14 26 31 P27 Ca/Al 19 8 12 8 63 40 51 49 23 8 20 P28 Ca/Bi 6 3 2 3 8 9 9 11 1 2 2 P29 Ca/Br 6 0 0 1 7 15 13 8 8 2 7 P31* Ca/Mg 13 5 3 6 44 28 37 27 63 10 15 P33 Ca/Mg/Al 5 1 0 0 21 15 15 13 9 5 3 P34 Ca/Mg/Na 30114947201 P35* Ca/Na 27 6 8 9 57 68 71 43 23 14 24 P38 Na/Ca 00000100000 P39 Ca/Na/Al Higher Ca 3 0 1 0 21 31 20 14 4 0 4 P40 Ca/Na/Al Lower Ca 00000000100 P42 Ca/Na/Br 10004544300 P43 Ca/Na/(Hg,W) 00000000000 P44 Na/Ca/Hg/Zr 00000000000 P45 Ca/Na/W 2 1 1 0 6 21 11 8 0 0 1 P46 Ca/W 10 4 5 3 19 23 22 21 14 4 10 P47 Ba/S/Bi 00104242000 P48 Ba/S/Na 00104350000 P49 Ca/Ba/S 00000000000 P50* Ca/S 24 11 11 8 92 76 58 85 2797 746 633 P57 Na/Ca/S 00000100000 P58 Na/S/Ca/Bi 1 0 2 0 5 24 7 13 8 6 3 P59 Na/S/Hg 00000901010 P60 Fe 24 5 7 7 6 5 8 11 1 3 5 P61 Fe/Al 24 4 12 7 16 4 18 14 0 3 2 P62 Fe/Cr/Na 7 7 12 8 1 7 12 106 5 5 5 P63 Fe/Na 52 6 12 17 21 17 38 19 4 10 9 P64 Fe/Al/Si 10 3 5 3 106 46 89 57 2 2 3 P65 Cl/Na/Ca 10000000000 P66 Cu/Cl/Ni 00000000000 P67 Hg,Mg,Na,W,Zr/Ca/Pb 51 1 1 5 0 5 3 2 2 0 0 P68 Ti/(Al,La,Na) 10 2 0 3 19 19 35 25 3 2 0 Total Particles 3613 1500 1757 2121 4000 4000 4000 3779 4000 1492 1742
Page 55 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
I. Variation Among Different Carpets The frequencies of occurrence of TPTs in a sampling of 21 carpets are shown in Table 32. Frequencies have been calculated per 4000 particles, the maximum number analyzed as set by computer-assisted SEM/EDS parameters. Average values of the three separate carpet areas are given for the carpets used for study of within-carpet variation.27
Some TPTs occur at high levels in only one to a few of the carpets. Two distinct examples are P57 (Carpet A) and P66 (Carpet F). Additional examples are P23, P34, P38, P40, P42 and P45. Three TPTs occur at low levels, but in only one or two carpets: P44 (Carpet BH), P49 (Carpet PH) and P65 (Carpet BH).
Some TPTs occur at moderate to high levels in several carpets, but are at very low levels in most. Examples are P39, P47, P48 and P67.
Some TPTs occur over a wide range of levels across the set of carpets. Notable examples are P31*, P35* and P50*. Other TPTs show a narrower range of levels, present in moderate to high levels in most of the carpets. Examples are P3 and P19.
Many of the carpets show a characteristic profile of TPTs distinguishing them from most others in this set of 21 carpets, based either on qualitative differences or large differences in the frequencies of specific TPTs.
Carpet PH stands out with high occurrences of calcareous TPTs containing sodium, and very low levels of siliceous and ferrous TPTs. There are very high levels of P35* and the highest observed levels of four other sodium containing calcareous TPTs: P39, P42, P45 and P46. Carpet PH is also one of the few carpets with occurrences of the two sulfurous TPTs, P47 and P48.
Carpet R5 is distinguished by high levels of TPTs P23, P50* and P58.
Carpet R3 has very high levels of TPTs P31* and P58, along with very low levels of P20 to P23. It is also one of the few carpets with co-occurrences of TPTs P39, P42 and P45.
Carpet F is the only one with very high levels of TPT P66 and is further characterized by only low levels of P50* and moderate levels of P23. The only other carpet with levels of TPT P66 is Carpet V1, which is further characterized by moderate levels of the three sulfurous TPTs P47, P50* and P58.
Carpet BH has very high levels of both TPT P67 and P68 as well as the highest levels in two of the ferrous TPTs, P60 and P63.
Carpet A is distinguished by its sulfurous and calcareous particles. It is the only carpet with occurrences of TPT P57, one of the few carpets with high levels of both TPTs P50* and P58, and
27 Specific occurrence data for all Carpet Areas and unconsolidated Target Particle Types are present in Appendix K. Incidence of Target Particle Types. Page 56 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association has the highest occurrence of P59. Carpet A also has the highest levels of occurrence for the rarely occurring calcareous TPTs P40 and P43.
Apart from Carpets BH and R5 (already distinguished by other TPTs), there are only two other carpets among the 21 with high levels of TPT P67: Carpets R7 and BV. These two are further distinguished from each other by their levels of P58, which are very high for Carpet R7 and negligible for Carpet BV.
Carpets R2 and W are the only ones with very low occurrences of TPTs P57 through P63. They are distinguishable from each other in their levels of occurrence of TPT 50* and differences in a number of TPTs where one carpet has very low or negligible occurrences and the other has low levels: P11, P13, P18, P20, P21, P28 and P29.
Carpet R1 has very high levels of TPTs P50* and P58, along with moderate levels of P59, very low levels of P47, and no occurrences of P67. Carpet R6 also has high levels of P50*, but moderate levels of P58, and, in contrast with Carpet R1, low levels of P67 and insignificant levels of P59.
Of the eight carpets not specifically mentioned above, additional discrimination is clearly possible using, for example, the broad range of frequencies seen for TPT 50*, and the ranges seen among several of the siliceous TPTs including P3, P13, P17 and P20.
Page 57 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Table 32. Frequency of Occurrence (per 4000 Particles) of Target Particle Types in 21 Carpets28
Residential Vehicular Workplace Carpet R1 R2 R3 R4 R5 R6 R7 A BH PH V1 V2 V3 V4 V5 BV F PV MT PL W Total Particles 642 4000 4000 3206 4000 4000 4000 3667 3649 3121 3422 1803 3485 1030 518 2092 661 3002 2771 3277 2535 P3 Si/Al Lower Si 150 192 80 302 72 147 138 82 50 11 144 211 216 163 154 126 129 149 105 68 155 P4 Si/Al Medium Si 12 15 29 42 14 36 80 53 34 0 19 35 55 31 31 31 8 21 18 12 16 P6* Si/Al/Ca 87 161 36 116 62 96 67 44 19 9 141 120 168 62 154 134 63 107 195 64 266 P8* Si/Al/Fe 25 49 31 76 42 56 56 55 20 9 46 106 67 62 100 41 34 145 48 24 90 P11 Si/Al/Mg Higher Mg 6 7 8 15 27 20 5 23 7 3 9 38 16 12 23 48 28 26 14 12 27 P12 Si/Al/Mg Lower Mg 25 16 15 39 25 29 29 33 18 3 30 95 62 35 46 32 18 63 30 15 58 P13 Al/Si/Na 0 7 6 130 75 24 61 61 21 8 14 16 38 0 8 21 26 110 66 14 52 P14 Si/Al/Na Lower Si 19 55 27 77 27 70 31 77 31 9 30 67 84 31 23 59 44 140 110 36 98 P17 Al/Si/W 19 34 27 64 32 38 39 29 46 27 35 67 79 39 54 79 2 218 119 44 52 Siliceous P18 Si/Al/S 12 2 17 25 11 12 30 4 3 0 22 13 10 16 39 29 4 10 19 7 14 P19 Si/Al/Sr 50 98 78 143 55 76 80 54 23 6 98 111 135 117 108 48 36 103 62 25 101 P20 Si/Al/Ca/Na 6 5 5 2 6 7 8 21 3 6 5 2 23 0 0 5 0 15 34 3 28 P21 Ca/Si/Mg 0 27 8 2 3 2 13 6 11 114008289343 P22 Si/Ca/Mg 12 43 5 30 31 46 14 32 15 4 42 35 45 39 31 31 16 44 50 20 61 P23 Si/Mg 6 3 1 9 187 10 1 15 2 2 4 2 7 4 23 6 46 3 4 4 6 P25 Si/W 12 20 9 22 8 19 8 15 17 15 14 24 15 16 31 69 12 47 75 31 16 P27 Ca/Al 44 151 85 55 61 135 36 47 46 189 76 171 67 82 100 41 38 53 77 65 53 P28 Ca/Bi 19 29 20 7 11 30 10 7 10 51 22 35 10 12 8 7 6 7 19 11 7 P29 Ca/Br 19 36 21 10 9 22 4 6 11 72 33 31 17 19 8 9 12 10 22 16 7 P31* Ca/Mg 69 101 252 80 61 112 69 152 122 127 35 78 38 101 69 32 159 32 89 71 40 P33 Ca/Mg/Al 31 32 87 22 11 24 29 37 35 10 11 11 26 23 15 5 22 16 29 15 13 P34 Ca/Mg/Na 0 2 13 0 0 0 1 51 11 20 02380324941 P35* Ca/Na 12 110 195 30 32 81 26 120 76 588 56 106 62 70 62 40 52 60 81 77 47 P38 Na/Ca 0 0 0 0 0 0 0 34 8000000000000 P39 Ca/Na/Al Higher Ca 6 22 49 4 3 4 10 24 12 101 5 9 17 4 8 5 4 26 10 11 15 Calcareous P40 Ca/Na/Al Lower Ca 0 0 0 0 0 0 0 60 15 300500100011 P42 Ca/Na/Br 0 2 14 0 1 0 4 3 5 49 17340106445 P43 Ca/Na/(Hg,W) 0 0 0 0 0 0 0 16 2610100000000 P44 Na/Ca/Hg/Zr 0 0 0 0 2 1 0 3 11 100000120001 P45 Ca/Na/W 0 10 33 4 1 2 4 13 14 93 5 4 13 0 0 3 0 14 5 9 5 P46 Ca/W 6 78 47 24 31 67 22 20 36 137 41 87 32 47 85 18 26 18 45 33 23 P47 Ba/S/Bi 31 3 3 1 8 7 4 1 3 73 159 7 16 19 0 3 10 3 4 1 3 P48 Ba/S/Na 12 1 0 0 0 0 1 3 2 65 15 7 10 0 0 1 2 3 1 0 1 P49 Ca/Ba/S 0 0 0 0 0 0 0 0 0 16 00000000000 P50* Ca/S 361 49 104 417 785 335 53 205 87 16 132 100 8 482 193 31 24 46 21 1643 297
Sulfurous P57 Na/Ca/S 0 0 0 0 0 0 0 51 0200000000001 P58 Na/S/Ca/Bi 517 5 855 19 96 88 345 246 70 23 89 4 6 4 8 1 6 2 6 20 7 P59 Na/S/Hg 50 0 19 0 2 1 4 74 14 14 40000000412 P60 Fe 12 5 6 10 11 27 5 6 86 0 14 7 11 19 15 21 38 6 18 10 5 P61 Fe/Al 31 5 10 17 16 22 9 4 14 1 15 22 17 23 8 18 28 12 9 7 9 P62 Fe/Cr/Na 0 2 0 5 0 1 0 5 18 2 1 13 6 12 8 8 10 31 2 6 0
Ferrous P63 Fe/Na 44 7 13 7 16 30 6 23 169 6 21 18 33 16 8 36 52 16 41 17 7 P64 Fe/Al/Si 12 15 11 30 28 25 18 12 16 3 21 40 24 12 46 17 6 79 22 12 25 P65 Cl/Na/Ca 0 0 0 0 0 0 0 0 16 000000100001 P66 Cu/Cl/Ni 0 0 0 0 0 0 0 0 0 0 15 0 0 0 0 0 278 0 0 0 0
Other P67 Hg,Mg,Na,W,Zr/Ca/Pb 0 1 2 2 49 28 140 6 381 3 4 13 9 4 0 116 12 1 2 2 3 P68 Ti/(Al,La,Na) 31 11 11 34 38 25 18 35 235 19 28 24 38 78 46 11 30 23 23 12 25 dark gray 0 to 5 gray 6 to 10 yellow 11 to 50 gold 51 to 200 red > 200 28 Frequencies are given per 4000 particles, the maximum number analyzed as set by computer-assisted SEM/EDS parameters. Average values of 3 separate carpet areas are given for Carpets A, BH, BV, F, MT, PH, PL, PV and W. Types with an asterisk are consolidated categories, as detailed in Table 21. Specific occurrence data for all Carpet Areas and unconsolidated Target Particle Types are present in Appendix K. Incidence of Target Particle Types. Page 58 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
IV. Conclusions
Our research has demonstrated that hundreds to thousands of very small particles (VSP) cling to the surfaces of individual carpet fibers. We have developed methods to remove these particles, analyze them, and use them to link the fibers to the carpet from which they came.
This project focused on one specific trace evidence application (carpet fibers) and one specific instrumental particle analysis method (computer-assisted SEM/EDS) to explore and test a fundamentally different approach to trace evidence analysis. In doing so, a set of reasonable assumptions and choices were made that can themselves be tested and refined for this specific application.
As proof of principle our findings are a highly significant breakthrough for the future of trace evidence analysis. They demonstrate a way to remove fundamental limitations of class associations and provide the impetus and direction for fundamental change in the way forensic trace evidence is conceptualized, analyzed and used in the criminal justice system. Further research is encouraged to allow the independent, quantitative testing of common origin using populations of VSP.
A. Discussion of Findings
All of the findings in this project are based on the analysis of carpets covering a limited range of characteristics (primarily trilobal, nylon fibers) and present in a limited set of environments. Accordingly, the conclusions made from these findings would apply only to these types of carpets. They serve as a model and as an initial study. As with any research, the initial efforts define a starting point. Further work on other carpet types can then be considered in reference to these data and the findings can then be either generalized or more definitively qualified.
Nine specific findings are discussed in this section:
1. Very small particles (VSP) present on the surfaces of individual carpet fibers can be recovered nearly completely and prepared for computer-assisted SEM/EDS analysis by extraction with reagent ethanol and filtration onto polycarbonate filters. 2. Hundreds to thousands of VSP routinely occur on the surface of individual carpet fibers. 3. VSP on individual carpet fibers, when classified using criteria developed for environmental applications, cannot be considered as an unbiased statistical sampling of a VSP population on the carpet itself. 4. Environmental particle groupings have significant weaknesses for investigation of VSP variation and were found to be unsuitable. 5. Clearly defined, mutually exclusive Target Particle Types (TPTs), based on the commonly occurring elemental profile groupings within samples, were found to be useful for study of the within- and between-carpet variations in VSP occurrence. 6. Among different areas of the same carpet, most TPTs showed comparable occurrence, or comparable absence. Some TPTs were localized. 7. Different carpets vary widely in the TPTs and quantities of VSP adhering to their fiber surfaces.
Page 59 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
8. When sufficient particles are recovered, individual fibers show highly characteristic patterns of TPTs that closely correspond to those from their originating carpet area. 9. Using a set of TPTs, VSP adhering to the surface of individual carpet fibers can be recovered, analyzed by computer-assisted SEM/EDS and used to associate these fibers with the carpet and carpet area from which they came.
1. Very small particles (VSP) present on the surfaces of individual carpet fibers can be recovered almost completely and prepared for computer-assisted SEM/EDS analysis by extraction with reagent ethanol and filtration onto polycarbonate filters.
Based on examination of fibers treated using a variety of solvents and agitation methods, the combination found to be most suitable for quantitative removal of very small particles (VSP) from commonly occurring carpet fibers was a ten-minute sonication in pure ethanol. Among those methods tested, this one resulted in the cleanest observed fibers without leaving a residue. The choice of ethanol as a solvent may not be optimum for recovery of VSP from all fiber types and it is not optimum for the recovery of all particle types. Fibers, both naturally occurring and man-made, have a range of chemical compositions, textures and surface treatments that will necessarily create a range of surface conditions with which any chosen solvent will interact. Any chosen solvent will also dissolve some portion of the particles present on the fiber’s surface. Ethanol will dissolve many organic substances, and VSP made up of such organic material will be irretrievably lost when ethanol is used. Some particles can also be significantly altered or lost due to agitation using sonication methods. Examples are particles that are fragile, friable, or loosely aggregated. One specific type of alteration is the disruption of a larger particle into many smaller ones. This could change both quantitative and qualitative results for a method based on the numbers of VSP with a specific chemical element profile. For this reason sonication was limited to a duration achieving effective particle removal.
A successful method was developed for recovery of the VSP removed from individual carpet fibers and preparation of the VSP for computer-assisted SEM/EDS analysis. This method uses filtration through a small (5 mm x 5 mm) area of a polycarbonate membrane filter with 0.4 μm pore size, followed by mounting on carbon tape and then carbon-coating. The use of a filter with pore size 0.4 μm defines the lower size limit for particle recovery by this method, since all particles passing through the filter are not recovered. Although additional, still finer VSP could be recovered by using a smaller pore size, the computer-assisted analysis is more efficient for the larger particles, as is the filtration process. Furthermore, the larger particles also include the size ranges of interest for evaluation of the impact of airborne pollutants on the environment and on public health. By focusing on this size range, forensic applications can benefit from heavily funded research and existing environmental monitoring programs that are serving these fields of study. None-the-less, alteration of the procedures to include finer particles would increase the numbers of VSP recovered, and could result in the detection of additional particle varieties or particles with special transport characteristics that occur only in this smaller size range.
The purpose of developing the method was to remove, as quantitatively as possible, VSP adhering to the surface of commonly occurring carpet fibers, so that the types and numbers of these particles could be characterized by computer-assisted SEM/EDS. For this purpose the
Page 60 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association method was well suited. SEM/EDS, as routinely applied in forensic science laboratories, is most applicable to particles in the size range that is recovered, and to inorganic particles, few of which will dissolve in ethanol. The method is effective, employs non-toxic materials, and is easy to apply. Practitioner review of the method established that it could be easily incorporated as a preliminary washing step prior to polarized light microscopy. With the development of this method, the first of the project objectives was achieved: to develop methods, compatible with existing fiber analysis protocols, and using currently available crime laboratory resources, to quantitatively remove and analyze the VSP adhering to carpet fibers.
2. Hundreds to thousands of VSP routinely occur on the surface of individual carpet fibers.
VSP isolated from individual fibers and analyzed by computer-assisted SEM/EDS varied in number from less than a hundred to greater than 4000 (the maximum number examined). After allowing for particles occurring in process blanks, there is an average of over 500 ethanol- insoluble VSP on the surface of a single carpet fiber. The confirmed presence of VSP in this quantity on carpet fibers enables research on the best means to analyze and interpret them, unlocking their extraordinary potential to enhance probative value and independently test hypotheses of common origin, as outlined in the guiding principles for this research effort.29
Almost certainly, the numbers of VSP present and recoverable from fiber surfaces will be related to the total amount of surface area on the fiber, as determined by its length, its width, and its cross-section. We did not test this relationship, but it is an important aspect that would affect the generalization of the findings. The fibers in this study were from 10 to 15 mm long, on the order of 70 micrometers in diameter, and almost all of trilobal cross-section. If shorter fibers were to be encountered in casework, for example, the available surface area would be less, and accordingly the numbers of particles present would be expected to be less. Our suspicion is that case-specific factors (e.g. how soiled the carpet is) would be the dominant consideration, irrespective of the fiber length.
The level of particle recovery in this study was more than sufficient for testing the specific program hypothesis and to achieve the related objectives to characterize within- and between- carpet variations in VSP profiles.
3. VSP on individual carpet fibers, when classified using criteria developed for environmental applications, cannot be considered as an unbiased statistical sampling of a VSP population on the carpet itself.
The hypothesis that the measured Environmental Particle Profiles on individual fibers represent an unbiased statistical sampling of the Environmental Particle Profiles on sets of ten fibers was strongly rejected. The specific program goal, to exploit existing computer assisted SEM/EDS methods to test whether the resulting fine particle profiles are useful to quantitatively associate shed fibers with a source carpet, was met.
29 See page 12. Page 61 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
4. Environmental Particle Groupings have significant weaknesses for investigation of VSP variation and were found to be unsuitable.
The principal weaknesses of the Environmental Particle Groupings are that many particle compositions have ambiguous group classifications and are based on only a small percentage of the particle’s composition.30 The groupings, based on percentages of the total x-ray counts for a suite of 28 elements, are typically based on percentages of 10 and 20%. This means that a particle having, say, 25% of four different elements, could easily fit criteria for more than one class. As an extreme example, a particle with the following percentages
Si Al Ca Fe S 0.45 0.22 0.12 0.12 0.12 would fit the criteria for 5 out of the ten particle classes. Another weakness is that for most of the classes, the majority of the elemental composition is ignored. Only one particle class (Ca-rich, defined as Ca>=60) is based on more than 50% of the x-ray counts. The remaining classes are based on from 10 to 40% of the counts.
The classification ambiguities in the environmental classification scheme are resolved by sequentially applying the classification criteria. Once a particle fits a class it is removed from consideration in the remaining classes. This approach is a reasonable one when targeting specific types of particles, with a defined priority, in a given environmental problem. There is a specifically designed flexibility in the order of application of the criteria, and in the definition of the criteria themselves. In practice, an initial classification scheme is used essentially as a presumptive or screening test, to identify candidate particles that might meet a targeted particle type of environmental concern. Images and x-ray spectra of these individual particles, or a sampling of them, can then be examined as “confirmatory testing.” Ignoring the majority of some particles’ composition is also reasonable for the environmental task; if particles don’t meet the presumptive screening criteria, they are conclusively not of interest and are disregarded.
Ultimately, once specific VSP of interest and significance are defined, a sequential analytical approach, such as described above may be extremely useful. Indeed, this is the approach taken for the analysis of gunshot residue (GSR) samples. The purpose of the current project, however, is the systematic investigation of VSP profiles on trace evidence and evaluation of their practical utility. The ambiguously defined, overlapping classes that are based on less than half of the elemental composition were found to be a poor means to investigate this variation.
5. Clearly defined, mutually exclusive Target Particle Types (TPTs), based on the commonly occurring elemental profile groupings within samples, were found to be useful for study of the within- and between-carpet variations in VSP occurrence.
30 See Table 7 on page 22 for the specific environmental particle classification criteria. Page 62 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
The deficiencies of the Environmental Particle Groupings were overcome by defining Elemental Profile Groupings based on the four highest x-ray counts of the 28 elements detected by the computer-assisted SEM/EDS procedure. Groupings occurring at the highest levels in 27 carpet area samples were used to define 68 mutually exclusive TPTs which were then used to study within- and between-carpet variation.
Of the 68 TPTs, eight were found to have high occurrences in the process blanks, leading to high Limits of Detection (LODs) relative to the levels of occurrence found in the samples. These levels of occurrence of particles in the process blanks were not anticipated. Possible sources for the particles are: reagents (ethanol), glass/plasticware, settling airborne dusts, and the polycarbonate filters. A number of preventative measures were taken to minimize contamination. The ethanol was pre-filtered. Glassware and plasticware were washed with the pre-filtered ethanol and the sample preparations were conducted on a clean bench. The filters themselves were used directly and not pre-washed, but they are marketed to be particle-free. In this study no direct attempts were made to determine the source of the particles in the process blanks. Overall, there was a limited range of TPTs occurring in the them, and after estimating LODs, a sufficient number of TPTs remained to meet program goals.
The selection of TPTs was based on their high levels of occurrence among a subset of the program samples. This was a reasonable choice as a starting point for investigation, but this choice is likely to be superseded after further work by a selection based on forensic performance characteristics, once the variability and sources of VSP become better understood. For example, VSP that are the most discriminating particle types, or those with the most consistent levels of occurrence, or those with the lowest LODs, may not be those that occur at the highest levels. A likely ultimate analytical strategy will be to use TPTs whose origin is known and whose distribution in the population is well understood, thereby providing a sound foundation for estimation of their variability and the determination of the significance of correspondence.
A TPT as used in this project is a functional grouping, made for its utility in this initial study of VSP variation. Some of the TPTs were closely related to one another chemically and occurred in similar relative proportions in the samples. This led to the consolidation of a number of TPTs. Even so, the extent of correlation among the TPTs has not been determined, and this is a clear, necessary step toward the understanding of their forensic performance characteristics and their adoption in a formal methodology.
The origin of the TPTs as defined in this project is uncertain. Many different sources could, and likely do, contribute to particles meeting many of the broadly defined TPT categories. Nor need the TPTs be of a single type. A commonly occurring combination of particles, as an aggregate, or as a smaller particle adhering to the surface of another, could create a separate TPT as defined in this study.
Possible sources for the particle types occurring on carpets include both indoor and outdoor dusts, originating from the building itself, from activities occurring within it, from materials that were intentionally or unintentionally brought in, or from those transported by air from the surrounding environment. Indeed, the carpet composition itself may be the source of some of the TPTs, through the wear of its backing materials, for example. This variety in the sources of VSP
Page 63 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
was anticipated and is part of the solution, rather than part of the problem. A central motivation for this project was to take advantage of these complex origins of VSP and to use the co- occurrence of many particle types to exploit those of modest frequency, leading to a highly probative test of common origin. However, an important part of the solution is also to a better understanding of the sources for the specific TPTs that are used for VSP characterization. At this stage of development, forensic performance characteristics of specific TPTs are poorly understood, and the initial criterion for selection, leading to their testing and evaluation in this project, was based on their levels of occurrence.
6. Among different areas of the same carpet, most TPTs showed comparable occurrence, or comparable absence. Some TPTs were localized.
Qualitatively, within-carpet variation for the TPTs was usually very low (~ 75% of the time), but occasionally ranged to very high for some TPTs and some areas (~ 13% of the time). This indicates an underlying, roughly even distribution of most particle types, together with occasional localized particle types. The findings do not support a single homogenized VSP distribution on fibers from a carpet, but they conclusively demonstrate that there are many particle types that occur with a sufficiently even distribution to be a useful for characterization.
The finding of some highly localized variability is not an unreasonable or unexpected result, given the likelihood of local carpet exposures to soiling or staining. Individual fibers can be exposed to a liquid, for example, and wicking along the fiber could well result in high levels of occurrence for those particles initially entrained in the liquid, but left behind once the liquid dries. Nearby carpet areas, with fibers that were not involved in the wicking process would lack these particles.
The effect of localized variation in carpets is both advantageous and challenging. Localized variation can provide additional spatial specificity to associations, but it also requires more comprehensive sampling. The sampling requirements would be analogous to soil cases, where localized variations occur along with more broadly occurring characteristics. At present, it is unknown how much sampling will be sufficient to effectively document a carpet’s within-item variation. One reasonable initial approach is to focus only on that (majority) of particles that are shared widely in a sampling of several areas of the reference carpet, or those that represent a specific stained area.
The need to take multiple reference carpet samples, and to perform multiple analyses to establish within-carpet variation, raises questions of practicality. What is the balance between the level of effort required and the possibility of added probative value? Clearly more must be known regarding both aspects before this can be evaluated, but two things can be anticipated. Firstly, there will be increased probative value as research reveals the best means to systematically exploit the VSP profiles that are present, and secondly, there will be increased efficiency as semi-automated and computer assisted methodologies develop. Both of these will increase the practicality of the approach.
Page 64 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
7. Different carpets vary widely in the TPTs and quantities of VSP adhering to their fiber surfaces.
The TPTs used to assess VSP variation among different carpets differed in their occurrence and discrimination potential across the set of 21 carpets studied in this project. Eight of the TPTs occurred at high levels in only one to a few of the 21 carpets studied, and another four TPTs occurred at moderate to high levels in several carpets, but at very low levels in most. Three other TPTs occurred over a wide range of levels across the full set of carpets. These 15 TPTs, in particular, are highly discriminating among the set of carpets.
Considering the profiles of VSP observed in each of the carpets, 12 of the 21 carpets are easily distinguished from one another based on qualitative differences and large differences in the frequencies of specific TPTs. The remaining eight carpets show a broad range of frequencies among five specific TPTs.
These findings provide a compelling demonstration of the potential of VSP to discriminate among areas from different carpets. The actual discrimination among carpets, as opposed to an area of a carpet, will be dependent on more complete studies of within-carpet variation and more carefully planned surveys of carpets. In this project our objective was to conduct a broader qualitative survey of carpet VSP profiles to explore between-item variation and to put the results of our investigations into a reasonable context. This objective has been met.
8. When sufficient particles are recovered, individual fibers show highly characteristic patterns of TPTs that closely correspond to those from their originating carpet area.
Very low particle totals were found on some individual fibers, but there was an average of over 700 per fiber. With few exceptions, when totals were over 1000, the TPT occurrences from individual fibers closely followed those from their originating area. The patterns were highly characteristic and showed both qualitative similarity, and similarities in rank and proportion. With lower totals (e.g. 300 to 800 particles), many fibers still showed reasonable similarities with their originating area.
TPTs allowed meaningful comparisons of the occurrences of VSP on individual carpet fibers. This directly supports a major project goal: to exploit existing computer assisted SEM/EDS methods to test whether VSP profiles are useful to quantitatively associate shed fibers with a source carpet. For the present methods, a strictly quantitative relationship among the full set of TPTs was not observed. However, the frequent occurrence of similarities in rank and proportionality, in separate experiments using multiple carpets and multiple areas within each carpet, establishes the proof of principle: VSP profiles on shed fibers can be measured, and they regularly correspond to reference samples taken from the area of the source carpet from which they came.
Page 65 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
9. Using a set of TPTs, VSP adhering to the surface of individual carpet fibers can be recovered, analyzed by computer-assisted SEM/EDS and used to associate these fibers with the carpet and carpet area from which they came.
This finding is supported by the overall program results, including: − Development and use of a practical method for the recovery of VSP from individual carpet fibers − Demonstration of the regular occurrence of VSP on individual carpet fibers, in quantity and character sufficient to associate them with their carpet area of origin − Development of a method suitable for the study of VSP variation, using a computer- assisted SEM/EDS analysis method based on TPTs − Establishing that within-carpet variations show a roughly even distribution for most TPTs − Establishing that between-carpet variations show a wide range in types and quantities of VSP, as demonstrated by TPT profiles
B. Discussion of the Underlying Technology and Scope
The exploitation of VSP to test the association of carpet fibers is a new approach, and one that lacks the comfort of actual particle identification and actual tracing of the source of the multitude individual particles. This differs from the exisiting paradigm where identification is a pre- condition to the use of particles, and where specificity in the measured characteristics provides the route to forensic utility. As discussed in the Introduction, the existing paradigm leads to fundamental limitations in our ability to interpret trace evidence. The impetus for the present research is to augment what is now being done, using VSP that we are currently ignoring, and using methods that will allow the combination of multiple characteristics that have measureable, testable frequencies of occurrence. These need to be valid characteristics, but they do not need to be particle identifications.
In particular, initial fundamental investigations such as this one must simplify the problem, in order to best learn what to study and improve. Within this context, moving forward requires trade-offs. Important aspects are the specificity of the particle characterizations, the reliability of their detection, the efficiency of the process, and the measureable, testable frequencies of occurrence. It is certain, for example, that better understanding of significance would follow from better identification of the VSPs, and that manual SEM/EDS particle imaging and EDS spectroscopy of individual particles would better and describe different particle types. Ultimately, if VSP are successfully exploited for associations, it is expected that other methods of VSP characterization, both more efficient and more specific will be developed.
At the present time, however, unambiguous identification of individual particles, attempting to determine their sources, and modeling evidential value based on characteristics of these sources is not the focus. TPTs are functional classifications consisting of groups VSP that share common characteristics as measured by a well-defined, practical methodology. SEM/EDS methodology is being used as a means to characterize thousands of particle X-ray count profiles and, by binning these profiles, to use populations of these particles in a useful way to test associations between carpet fibers and possible source carpets.
Page 66 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
C. Implications for Policy and Practice
Five specific implications for policy and practice are discussed in this section:
1. The usefulness of VSP to remove fundamental limitations to the probative value of carpet fiber evidence has been demonstrated, providing the impetus and direction for fundamental change in the way that forensic trace evidence is conceptualized, analyzed and used in the criminal justice system. 2. The results of this research are likely extendable, with minor modifications, to other trace evidence types, and are expected to contribute significantly for those types of trace evidence that have long been considered of low evidential value. 3. An entirely new approach to trace evidence is enabled: comparing different types of trace evidence with one another by way of their adhering VSP. 4. An additional, high priority use for existing crime laboratory SEM/EDS analytical capabilities and related practitioner skills can now be anticipated, guiding the allocation of laboratory resources. 5. A need can be anticipated for policies and practices for evidence collection and processing of crime scenes that are sensitive to requirements for the preservation and analysis of VSP.
1. The usefulness of VSP to remove fundamental limitations to the probative value of carpet fiber evidence has been demonstrated, providing the impetus and direction for fundamental change in the way that forensic trace evidence is conceptualized, analyzed and used in the criminal justice system.
This project has increased our fundamental understanding of the next (finer) dimension of particles, and the potential use of these particles in one specific trace evidence application has been established. The implications for policy and practice are profound. The fundamental limitation to the probative value of trace evidence, noted in the NRC report,[5] stems from conventional trace evidence characteristics being determined by their manufacture. As mass- produced commodities, probative value is limited to class associations, with qualitative, expert assessments of evidential value. The analysis of VSP, riding "piggy back" on the surface of other trace evidence particles, can remove this fundamental limitation, by adding independent, quantitative, objectively measured fine particle profiles that have accumulated from the environment during use in a specific location. This will lead to much more sensitive testing of associations, and more certain and convincing associative evidence.
At the outset of this project, the existence of useful VSP profiles on the surface of carpet fibers had yet to be established. This has now been conclusively demonstrated. There is now a clearly achievable impact of these methods that will remove the fundamental limitations discussed above, increase the probative value of trace evidence and provide an independent quantitative means to test hypotheses of common origin. The occurrence, with modest frequency, of specific TPTs will ultimately be estimated, and with such modestly occurring events upper bounds on frequencies and correlations can be reliably estimated. It is the co-occurrence of multiple events
Page 67 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association of modest frequency that is the foundation for all highly probative types of physical evidence, including DNA and fingerprint identifications. To unlock this potential, further research will be required that (1) determines which TPTs have the best forensic performance characteristics, (2) rigorously documents within- and between- carpet variability for these TPTs, (3) optimizes the analytical protocol, (4) determines how susceptible VSP profiles are (post shedding) to contamination and loss, and (5) develops and validates quantitative methods for the testing of common origin using VSP.31
2. The results of this research are likely extendable, with minor modifications, to other trace evidence types, and are expected to contribute significantly for those types of trace evidence that have been considered of low evidential value.
The results of this research have implications for other types of trace evidence: for example, there are VSP adhering to other types of fibers, hair, glass, and paint. Some types of evidence, now of extremely low value for trace evidence associations (such as undyed cotton fibers) may become highly useful for association based on the VSP that adheres to them. The morphological examination of hair, for example, vulnerable to criticism based on subjectivities and variations in methodology, can be supplemented by comparisons of adhering VSP. In extension of the research to these areas, the methodologies and interpretations will be similar. That is, separate studies of fine particle populations for each type of trace evidence are unlikely to be necessary, since what is being compared are the particles from the environments. This is a noteworthy advantage over the use of new types of trace evidence that would each require their own separate study of population frequencies.
3. An entirely new approach to trace evidence is enabled: comparing different types of trace evidence with one another by way of their adhering VSP.
Any trace evidence type can act as the specific carrier of a more general “VSP signal.” Any fiber from a residence, for example, could carry VSP corresponding to any other fiber. They need not be fibers from the same carpet. Extending this somewhat further, VSP on a knife or tool left at a crime scene could, for example, be linked with VSP from a suspect’s residence, or VSP on the edges of tape on the inside of an IED could be linked with that found on the edges of an entirely different kind of tape in a suspect’s workshop.
4. An additional, high priority use for existing crime laboratory SEM/EDS analytical capabilities and related practitioner skills can now be anticipated, guiding the allocation of laboratory resources.
The computer-assisted SEM/EDS methods used for analysis of VSP on carpet fibers were specifically developed with a view toward utilization of existing crime laboratory equipment and related practitioner skills. Some laboratories utilize nearly identical methods in support of GSR analysis. Others use closely related equipment and skills as a part of materials analysis and
31 The specific implications for this further research are discussed in the following section. Page 68 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
characterization. The anticipation of an additional high priority application will impact policy and practice as it will provide additional impetus and objectives for the retention and further development of capabilities in these areas. As an alternative, there are possibilities for commercial outsourcing of these types of analyses, which are already in place as applied to GSR and environmental dust analyses.
5. A need can be anticipated for policies and practices for evidence collection and processing of crime scenes that are sensitive to requirements for the preservation and analysis of VSP.
As methods for the exploitation of VSP come closer to implementation, a need for appropriate evidence collection and processing methods can be anticipated. These methods will include collection of appropriate control samples and information that would help to interpret the presence of VSP that may be present. The requirements for actual collection practices will only be clear after additional research, but at this point a need for such methods can be anticipated.
D. Implications for Further Research
The establishment of useful VSP profiles on the surface of individual carpet fibers provides both the impetus and direction for follow-on research. This research can be broadly divided as (1) that focused on developing the specific application of computer-assisted SEM/EDS analysis of VSP on carpet fibers, and (2) that focused on expanding the VSP approach to other applications.
For the specific carpet fiber application, proof of principle has been established with the development of practical methodologies, establishment of workable within-item variability and the measurement of corresponding profiles on individual fibers. The focus for this application now shifts to direct follow-on steps, the most important of which are: (1) determining which TPTs have the best forensic performance characteristics for carpets, (2) rigorously measuring within and between variability for these TPTs, (3) optimizing the analytical protocol, (4) determining how susceptible shed fibers are to contamination and loss of VSP profiles, and (5) developing and validating quantitative methods for the testing the origin of carpet fibers using VSP.
For expansion of the VSP approach, additional alternative directions are (6) application to other trace evidence types, (7) application of other instrumental analysis methods, (8) the use of VSP to associate an environment with an object and (9) more general development and validation of quantitative methods for the use and interpretation of VSP.
1. Determining Which TPTs have the Best Forensic Performance Characteristics for Carpets
TPTs must be studied to determine which have the best forensic performance characteristics for the linking carpet fibers to carpets. Performance characteristics take into account the combination of occurrence within samples, correlations among TPTs, discrimination among samples, levels of detection, and reliabilities of detection.
Page 69 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Multivariate statistics are essential for investigation of correlations and discrimination. Principle components analysis, or one of the more modern approaches to discriminant analysis, needs to be employed.
Another very important aspect for effective assessment of forensic performance characteristics is having a good understanding of the actual identity and (generic) source of the particles. Some sources may be inherently highly correlated, either with one another, or with a particular brand or composition of carpet. The experience of the broader scientific community in the analysis of respirable particles of environmental, public health and occupational health significance is directly applicable. This experience needs to be incorporated, but built upon and augmented to include additional types of particles that occur routinely in human dwellings or vehicles and that are not of interest to these disciplines.
2. Rigorously Measuring Within and Between Variability for these TPTs
Variability, both within and between carpets, must be better understood. Investigation of within- carpet variability will require testing of carpet samples taken comprehensively from entire rooms, entire buildings and entire areas of vehicles. Shed fibers, as opposed to cut fibers from fabric, will need to be included in these tests. The length of such fibers is an important parameter to include among those studied.
Investigation of between-carpet variability will require testing of carpets from different geographical areas, and testing multiple locations in the same geographical area. As with research on performance characteristics, knowledge of the actual source of the particles, when determinable, will lead to greater understanding of the factors contributing to their variability.
3. Optimization of the Analytical Protocol
Parameters for the computer-assisted SEM/EDS method employed in this project were chosen as those found to be reasonable for characterization of environmentally significant particle types. These parameters need to be reconsidered and tested, now that the application itself is better defined. This research is linked with the determination of which TPTs have the best performance characteristics for carpets and the two research tasks must run in parallel.
For example, parameters for analysis in this project included particles in a broad size range (0.4 to 50 μm). A narrower size range may be better for VSP profile comparisons in carpets. Easily airborne, respirable particles, with a particle size up to about 10 μm, may well be more evenly distributed on carpets than larger particles. If so, omission of larger particles may eliminate some of the highly localized TPT occurrences that are seen. Other aspects of the method could have similar effects, such as changing the range of elements analyzed, the maximum number of particles analyzed, the detection thresholds, and the particular algorithms that are used as tests for specific TPTs.
Page 70 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
Overall, SEM/EDS methods related improvements that should be considered as part of further research are: • Inclusion of manual SEM/EDS particle imaging and viewing of SEM/EDS spectra for identifying and discussing the TPTs • Inclusion of the analysis of known materials or known examples of TPTs a quality control procedure • Conducting manual SEM analyses on samples and comparison with the computer- assisted data as a quality control procedure for possible peak misidentifications • Extension of the particle size range (and thereby the particle numbers) by using a backing filter to collect smaller particles and employing a higher magnification in the SEM
4. Determining How Susceptible Shed Fibers are to Contamination and Loss of VSP Profiles
Forensic applications will be based on the transfer of carpet fibers from a source carpet to an object or person. During or post transfer, VSP profiles on carpet fibers are subject to contamination (acquisition of additional VSP) or losses (loss of some of the originally adhering VSP). These changes may occur very slowly, and at low levels, or may occur quickly. There may be exchange with those VSP on a receiving substrate. Losses, should they occur, may be proportional (all VSP affected evenly) or disproportional (some types of VSP markedly more subject to retention or loss). The levels of occurrence of any such effects are unknown. If they occur, they need not greatly affect the methodology in actual application, but they must be understood in any case. Additionally, the consequences of fiber recovery methods (such as taping and scraping) need to be evaluated.
5. Development and Validation of Quantitative Methods for the Testing the Origin of Carpet Fibers using VSP
A rigorous quantitative means for interpretation of VSP profiles will be the ultimate outcome of this research program, building on each of the four contributions mentioned above − TPTs with high forensic performance parameters for carpets − rigorously measured of within- and between-carpet VSP variability − an optimized analytical protocol − known limits on the effects of contamination and loss
With these inputs a well-defined quantitative interpretive model for carpet fiber evidence must be developed and validated using appropriate experimental trials and statistical tests.
6. Application to Additional Trace Evidence Types
As noted under Implications for Policy and Practice, the results of this research are likely extendable, with minor modifications, to other trace evidence types, and are expected to contribute significantly for those types of trace evidence that have been considered of low evidential value. The two types specifically mentioned were undyed cotton fibers, currently
Page 71 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association considered of nearly no probative value for association, and hairs, currently vulnerable to criticism based on subjectivities and variations in methodology. The ability of VSP to test associations for these two evidence types would have a highly significant, immediate impact.
7. Application of Other Instrumental Analysis Methods
SEM/EDS is not the only candidate for the analysis of VSP. Particle profiles can be analyzed by a growing number of high-throughput methods based on light or electron microscopy, Raman microscopy, FTIR microspectroscopy, Raman microspectroscopy or even methods of molecular biology as applied to non-human DNA. Additional techniques will be forthcoming and each should be evaluated for a possible niche in the forensic analysis of VSP.
8. Use of VSP to Associate an Environment with an Object
Again, as noted under Implications for Policy and Practice, an entirely new approach to trace evidence is possible using VSP: comparing different types of trace evidence with one another. Any trace evidence type can act as the specific carrier of a more general “VSP signal.” These methods are essentially comparing an environment (via its VSP profile) to items that could have originated from that environment. Any item or piece of trace evidence originating from a crime scene can potentially be linked to that crime scene using the crime scene’s VSP profile.
9. General Development and Validation of Quantitative Methods for the Use and Interpretation of VSP
Parallel to the specific development and validation of quantitative methods for carpet fiber applications, research providing inputs to more general applications will include better understanding of forensic performance parameters of a broader set of TPTs, generalizations (as possible) of their within- and between-item variability, correlations among them, and the limits of contamination and loss during contact and transfer.
Page 72 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
V. References
1. Stoney, DA "Transfer Evidence," In: The Use of Statistics in Forensic Science, CGG Aitken and DA Stoney, Eds., Prentice Hall, New York, pp. 107-138, 1991.
2. Stoney, DA “Statistical Applications in Trace Evidence,” Trace Evidence Symposium, International Symposium on the Forensic Examination of Trace Evidence in Transition, FBI Laboratory Division, San Antonio, TX, June 28, 1996.
3. Houck, MM, "Statistics and the Tyranny of Numbers," Forensic Science Communications 1(3) October, 1999.
4. Koons, RD "Use of Statistics in Evaluation of Trace Evidence,” Trace Evidence Symposium, Clearwater Beach, FL, August 15, 2007
5. National Research Council, Strengthening Forensic Science in the United States: A Path Forward, National Academies Press, Washington, D.C., 2009, 161-163,167-170.
6. Stoney, D and Stoney, P. “Time to Re-Think Dusts,” NIJ/FBI 2011 Trace Evidence Symposium, Kansas City, MO, August 11, 2011. Available at http://projects.nfstc.org/trace/ 2011/presentations/Stoney-Dusts.pdf
7. Cwiklik C. An Evaluation of the Significance of Transfers of Debris: Criteria for Association and Exclusion. Journal of Forensic Science 1999 ; 44 (6) : 1136-1150.
8. e.g., Deadman, HA, Fiber Evidence and the Wayne Williams Trial (Part1), FBI Law Enforcement Bulletin, pp. 13-20, March, 1984; Deadman, HA, Fiber Evidence and the Wayne Williams Trial (Conclusion), FBI Law Enforcement Bulletin, 10-19, May, 1984.
9. Robertson, J and Roux, C. From the Crime Scene to the Laboratory - Transfer, Persistence and Recovery of Fibres, in Grieve, M and Robertson, eds. J. Forensic Examination of Fibers, 2nd edition, London: Taylor and Francis, Ltd., 1999, pp. 89-100.
10. ASTM E1588-07, Standard Guide for GSR analysis by Scanning Electron Microscopy/Energy Dispersive X-ray Spectrometry, American Society for Testing and Materials, West Conshohocken, PA, 2007.
11. See, for example, Morawska, L and Salthammer, T, eds., Indoor Environment: Airborne Particles and Settled Dust, Wiley, 2004.
12. Siegel JA. Evidential value of textile fibre - transfer and persistence of fibres. Forensic Science Review 1997; 9 (2): 81-96.
13. Grieve, M and Robertson, J. Forensic Examination of Fibers, 2nd edition, London: Taylor and Francis, Ltd., 1999.
Page 73 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
14. SWGMAT Forensic Fiber Examination Guidelines Forensic Science Communications 1(1) April, 1999.
15. SWGMAT, Fiber Subgroup, Forensic Fiber Examiner Training Program, Federal Bureau of Investigation, Laboratory Division, May, 2004.
16. World Health Organization, Hazard Prevention and Control in the Work Environment: Airborne Dust, WHO, Geneva, 1999.
17. Conner, TL, Norris, GA, Landis, MS and Williams, RW; Individual Particle Analysis of Indoor, Outdoor and Community Samples from the 1998 Baltimore Particulate Matter Study, U.S. EPA, Office of Research and Development, National Exposure Research Laboratory, Human Exposure and Atmospheric Sciences Division Research Triangle Park, NC, 27711. (Also published without figures in Atmospheric Environment 35: 3935-3946, 2001)
18. Willis, RD, Blanchard, FT and Conner, TL. Guidelines for the Application of SEM/EDX Analytical Techniques to Particulate Matter Samples, National Exposure Research Laboratory, U.S. Environmental Protection Agency, EPA # 600/R-02/070 September 2002.
19. Casuccio, GS et al. Characterization of Ambient Particulate Matter Using Electron Microscopy and Raman Spectroscopy Techniques, NETL Conference on PM2.5 Electric Power Generation, Recent Findings and Implications, Pittsburgh, PA, April 10, 2002.
20. Engelbrecht, JP, et al., Characterizing Mineral Dusts and Other Aerosols from the Middle East – Part 1: Ambient Sampling, Inhalation Toxicology 21(4):297-326, 2009; and Characterizing Mineral Dusts and Other Aerosols from the Middle East—Part 2: Grab Samples and Re-Suspensions, Inhalation Toxicology 21(4):327-336, 2009.
21. Schwoeble, AJ and Exline, DL, Current Methods in Forensic Gunshot Residue Analysis, CRC Press, 2000.
22. Romolo, FS and Margot, P. Identification of gunshot residue: a critical review, Forensic Science International 119: 195-211, 2001.
23. Wright, DM and Trimpe, MA; Summary of the FBI Laboratory's Gunshot Residue Symposium, May 31-June 3, 2005; Forensic Science Communications 8(3) July, 2006.
24. GSR procedure, Section 4.8, pages 72-92, Trace Evidence Unit manual, 05-08-2009, San Diego Police Department Crime Laboratory.
25. Roux, C., et al. “Forensic Science in the 21st Century: Will Trace Evidence Ever Reach the Next Level?,” Trace Evidence Symposium, Clearwater Beach, FL, June 16, 2007
Page 74 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
26. Roux, C, Langdon, S, Waight, D and Robertson, J., The transfer and persistence of automotive carpet fibres on shoe soles. Science & Justice 39(4):239-251, 1999.
27. Willis, RD, Blanchard, FT and Connor, TL. (2002) Guidelines for the Application of SEM/EDX Analytical Techniques to Particulate Matter Samples. U.S. Environmental Protection Agency #600/R-02/070.
28. Faegri, K and Iverson, J. (1989) Textbook of Pollen Analysis; 4th Ed. The Blackburn Press, Caldwell, NJ.
29. Palenik, S. (2007) Heavy Minerals in Forensic Science. In Mange, MA and Wright, DT (Eds.), Heavy Minerals in Use. Elsevier, Amsterdam, The Netherlands.
30. ASTM. (2002) ASTM D422-63(2002) Standard Test Method for Particle-Size Analysis of Soils. ASTM International.
31. Porter, JJ. (1962) Electron microscopy of sand surface textures. Journal of Sedimentary Petrology, 32: 124-135.
32. Kelley, JC, Mathematical Analysis of Point Count Data. In Carver, RE (Ed), Procedures in Sedimentary Petrology, Wiley, NY, 1971
Page 75 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.
Technical Report 2010-DN-BX-K244 Small Particles on Fibers to Test Association
VI. Dissemination of Research Findings
1. Presentations Resulting from this Award (as of 1/30/12)
Bowen, A. “A Procedure for Recovering Fine Particles from Carpet Fibers,” Inter/Micro 2011, Chicago, IL, July 11, 2011.
Stoney, DA, Bowen, A and Stoney, PL. “Time to Rethink Dusts,” NIJ/FBI 2011Trace Evidence Symposium, Kansas City, MO, August 11, 2011.
Stoney, DA, Bowen, A and Stoney, PL. “Use of Computer Controlled Scanning Electron Microscopy (CCSEM) Methods for the Analysis of Small Particles Adhering to Carpet Fiber Surfaces,” San Diego Police Department Crime Laboratory, Trace Evidence Section, San Diego, CA, December 5, 2012.
Stoney, DA, Bowen, A and Stoney, PL. “Use of Computer Controlled Scanning Electron Microscopy (CCSEM) Methods for the Analysis of Small Particles Adhering to Carpet Fiber Surfaces,” American Academy of Forensic Sciences, 40th Annual Meeting, Atlanta, GA, February 25, 2012. (Upcoming)
2. Publications Resulting from this Award (as of 1/30/12)
A New Method for the Removal and Analysis of Small Particles Adhering to Carpet Fiber Surfaces, (Accepted with Minor Revisions, publication pending as a Technical Note).
3. Training Module
A training module was developed and has been delivered as an attachment to this report: Appendix L. Training Module.
Page 76 of 76
This document is a research report submitted to the U.S. Department of Justice. This report has not been published by the Department. Opinions or points of view expressed are those of the author(s) and do not necessarily reflect the official position or policies of the U.S. Department of Justice.