TALON EPOXY FOR PLASTIC EPOXY REPAIR PUTTY EPP-SPEC

PRODUCT DESCRIPTION COLOR/CONSISTENCY PACKAGING

PRODUCT Gray Base/White Hardener. Dries to a Shipping case contains two display cartons uniform white color. Heavy, one part putty each containing 12 - 4 oz. (113.4 g) plastic TALON EPOXY FOR PLASTIC in cylindrical form. containers of TALON EPOXY FOR PLASTIC. TYPE PERFORMANCE DATA U.S. Measure: TALON EPOXY FOR PLASTIC is a one TALON EPOXY FOR PLASTIC will part epoxy repair putty in stick form with harden like steel in 20-25 minutes at room Stock Code Size the hardener and resin in the same roll. It temperature. Plastic Tub will cure to a rock-like consistency in 20 - EPP4 4 oz. (113.4 g) 25 minutes. It is a nontoxic, moldable TEMPERATURE RANGE FOR putty which is clean to use. Adheres to APPLICATION SHIPPING WEIGHT PER CASE wet and dry surfaces including: ceramic, cement, non-flexible plastics and painted 20°F (-6°C) to 130°F (54°C) Stock surfaces. Does not contaminate liquids Code Case Weight #/Case or gases. Even cures under water! TEMPERATURE RANGE USE AFTER EPP4 8 lbs. (3.6 kg) 24 Won’t shrink or sag and resist oils, CURING greases, alkalis, detergents, and many solvents. TALON EPOXY FOR Liquids/Gases: WEIGHT PER U.S. GALLON PLASTIC is easy to use, just cut off an -50°F (-45°C) to 300°F (148°C) amount of putty desired and mix in hands 15.2 lbs. (3.6 kg) ± 0.02 until a uniform color and consistency. PRESSURE RANGE USE TALON EPOXY FOR PLASTIC can be DIRECTIONS FOR USE drilled, tapped, sawed, filed or painted. Liquids/Gases: 1. Lightly sand or scuff the surface with up to 300 PSI (43.51 kPa) RECOMMENDED USES WHITLAM Sand Cloth or WHITLAM Open APPLICATION PRECAUTIONS Mesh. TALON EPOXY FOR PLASTIC repair putty is recommended for use on PVC, IF TAKEN INTERNALLY, INDUCE 2. Clean the surface of any foreign material ABS, and Vinyl. TALON EPOXY FOR VOMITING AND CALL PHYSICIAN to ensure a good bond. PLASTIC repairs leaks in pipes and tanks IMMEDIATELY. FOR EYE AND SKIN without draining the system. CONTACT, FLUSH WITH PLENTY OF 3. Tear or cut off required amount needed WATER. with gloved hands. Rebuild: rigid and semi-flexible plastics. WARNING: 4. With gloved hands, knead thoroughly so Repairs: automotive trim, appliance parts, EYE IRRITANT. complete mixing is achieved. Material should outdoor furniture, vinyl siding and more. HARMFUL OR FATAL IF be a uniform color. For best results use SWALLOWED. TALON EPOXY FOR PLASTIC to room Also recommended for sealing leaking KEEP AWAY FROM CHILDREN. temperature or slightly above. plastic pipe, anchoring bolts in plastic, and WASH HANDS AFTER MIXING. making a permanent waterproof electrical 5. Apply to clean surface to be repaired connection. Plus thousands of other SEE SAFETY DATA SHEET (SDS) FOR within 10 minutes of mixing, and work into uses. COMPLETE PRECAUTIONS FOR SAFE position. For best adhesion, force into any HANDLING AND USE. cracks or holes. Extend patch at least 1 inch beyond area of repair. Remove excess ENVIRONMENTAL STATEMENT material, preferably with a tool moistened with clean water prior to hardening begins. When mixed by hand TALON EPOXY FOR PLASTIC does not cause skin irritation to When applying to a damp, wet or slowly individuals with normal skin sensitivity. leaking area, work the mixed epoxy putty Individuals with extra-sensitive skin should forcefully into the surface and apply pressure maintain caution and wash hands after until adhesion begins to take effect. mixing the compound.

ELECTRICAL CONDUCTIVITY

TALON EPOXY FOR PLASTIC is nonconductive. P.O. Box 380 ● Wadsworth, OH 44282 U.S.A. Phone: 1-330-334-2524 ● FAX 1-330-334-3005 EPP-SPEC Email: [email protected] © 2020 J.C. Whitlam Manufacturing Company Website: www.talonepoxy.com This product is manufactured in the U.S.A. .

The information contained in this bulletin is correct to the best of our knowledge. The recommendations or suggestions herein are made without guarantee or representation as to result, since the conditions of use are beyond our control. We suggest that you evaluate the recommendations contained in this bulletin. No statement is to be construed as violating any copyright or patent. They are intended only as a source of information.