Remove/Install Bulbs of Headlamp Unit 23.4.07 MODEL 221.0 /1

AR82.10-P-1201SX Remove/install bulbs of headlamp unit 23.4.07 MODEL 221.0 /1

P82.10-4330-09 Shown on the left front lamp unit 1 Housing cover E1 Left front headlamp unit E2 Right front headlamp unit 2 Bolts E1e2 Left low beam (without code E2e2 Right low beam (without code 3 Housing cover (615) Bi-xenon headlamp unit (615) Bi-xenon headlamp unit 4 Housing cover with integrated curve with integrated curve 5 Housing cover illumination) illumination) 6 Cornering illumination socket E1e3 Left standing and parking lamp E2e3 Right standing and parking (with code (615) Bi-xenon E1e5 Left turn signal lamp lamp headlamp unit with integrated E1e9 Cornering illumination (with E2e5 Right turn signal lamp curve illumination) code (615) Bi-xenon headlamp E2e9 Cornering illumination (with 7 Low beam socket (without code unit with integrated curve code (615) Bi-xenon headlamp (615) Bi-xenon headlamp unit with illumination) unit with integrated curve integrated curve illumination) E1e10 Left bi-xenon lamp with illumination) 8 Mounting clamp (with code (615) integral ignition module (with E2e10 Right bi-xenon lamp with Bi-xenon headlamp unit with code (615) Bi-xenon headlamp integral ignition module (with integrated curve illumination) unit with integrated curve code (615) Bi-xenon headlamp 9 Electrical connector illumination) unit with integrated curve (with code (615) Bi-xenon illumination) headlamp unit with integrated curve illumination) 10 Standing and parking lamp socket

Copyright Daimler AG 8/11/10 G/01/08. This WIS printout will not be recorded by the update service. Page 1 P82.10-4331-09 Shown on the left front lamp unit 4 Housing cover 14 High beam socket (without E2 Right front headlamp unit 11 Electrical connector code (615) Bi-xenon headlamp E2e1 Right high beam (with code (610) Night View unit with integrated curve E2e11 Right infrared lamp (with code illumination) (610) Night View Assist) Assist) 12 Infrared lamp socket E1 Left front headlamp unit (with code (610) Night View E1e1 Left high beam Assist) E1e11 Left infrared lamp (with code (610) Night View Assist) 13 High beam socket (with code (615) Bi-xenon headlamp unit with integrated curve illumination) Modification notes 16.4.07 Repair method for removing standing lights and parking lights modified

Figure item, etc. Work instructions Danger! Risk of death caused by high voltage levels Do not come into contact with parts that are AS82.10-Z-0001-01A present at xenon headlamps. under high voltage. Persons with active Risk of explosion/fire hazard due to highly electronic implants (e.g. heart pacemakers) flammable substances in the area of must never work on xenon headlamps. damaged xenon bulbs Switch off entire lighting system. Wear Risk of injury due to UV light, hot insulated safety shoes, safety glasses and components on xenon headlamps and glass protective gloves. Remove highly splinters when xenon bulbs burst inflammable materials from the hazard area. Risk of poisoning caused by inhalation of Ensure sufficient ventilation in the working mercury vapors and by toxic salts and area. mercury compounds being ingested or coming into contact with skin Do not touch the glass bulb elements of the bulbs with fingers, but use a soft cloth free of oil and grease; otherwise the bulbs can be damaged by overheating during operation Switch off the exterior lights prior to making a bulb replacement in order to avoid a short circuit Switch off ignition and withdraw transmitter Keyless Go start/stop button only on vehicles key or Keyless Go start/stop button from the with code (889) Keyless Go. EIS [EZS] control unit Remove/install lamp unit When replacing left turn signal light (E1e5) or AR82.10-P-4730SX right turn signal light (E2e5). Remove/install fender liner front section on When changing left standing and parking front fender lamp (E1e3) or right standing and parking lamp (E2e3).

Copyright Daimler AG 8/11/10 G/01/08. This WIS printout will not be recorded by the update service. Page 2 Unfasten/fasten expansion reservoir with When exchanging right low beam (E2e2) or lines connected right bi-xenon lamp with integral ignition module (E2e10). Unfasten/fasten windshield washer system On vehicles without code (487) Active Body AR82.35-P-6000-01SX washer fluid reservoir Control (ABC) to exchange left low beam (E1e2) or left bi-xenon lamp with integral ignition module (E1e10). Remove/install washer fluid reservoir top On vehicles with code (487) Active Body section from windshield washer system Control (ABC) to exchange left low beam (E1e2) or left bi-xenon lamp with integral ignition module (E1e10). Refer to: Remove/install washer fluid reservoir of AR82.35-P-6000SY windshield washer system E1e1, E2e1 Left high beam, right high beam Detach housing cover (4), twist high beam socket (14) or high beam socket (13) to the left and remove. Pull left high beam (E1e1) or right high beam (E2e1) out of high beam socket (14) or out of high beam socket (13). E1e2, E2e2 Left low beam, right low beam On vehicles without code (615) Bi-xenon headlamp unit with integrated curve illumination. Detach housing cover (3), twist low beam socket (7) to the left and remove. Pull left low beam (E1e2) or right low beam (E2e2) out of low beam socket (7). E1e3, E2e3 Left standing and parking lamp, right Twist socket for standing and parking standing and parking lamp lamp (10) to left and remove. Remove left standing and parking lamp (E1e3) or right standing and parking lamp (E2e3) from standing and parking lamp socket (10). E1e5, E2e5 Left turn signal lamp, right turn signal lamp Remove screws (2) on housing cover (1) and remove housing cover (1). Remove left turn signal lamp (E1e5) from left front lamp unit (E1) or right turn signal lamp (E2e5) from the right front lamp unit (E2). E1e9, E2e9 Cornering illumination On vehicles with code (615) Bi-xenon headlamp unit with integrated curve illumination. Detach housing cover (5), twist cornering illumination socket (6) to the left and remove. Pull cornering illumination (E1e9) or cornering illumination (E2e9) out of cornering illumination socket (6). E1e10, E2e10 Left bi-xenon lamp with integral ignition On vehicles with code (615) Bi-xenon module, right bi-xenon lamp with integral headlamp unit with integrated curve ignition module illumination. Remove housing cover (3), undo mounting clamp (8), pull out left bi-xenon lamp with integral ignition module (E1e10) or right bi-xenon lamp with integral ignition module (E2e10) and detach electrical connector (9). E1e11, E2e11 Left infrared lamp, right infrared lamp On vehicles with code (610) Night View Assist. Detach housing cover (4), unplug electrical connector (11), twist infrared lamp socket (12) to the left and remove. Pull left infrared lamp (E1e11) or right infrared lamp (E2e11) out of infrared lamp socket (12).