Classic Dual

CLASSIC DUAL

SKU# PASCLAS19-02 WWW.POP-A-SHOT.NET Read all instructions: All the safety and operating instructions should be read carefully before this product is operated or played. Caution: This is not a toy and is intended for use by or under the supervision of adults. Adults should review safety guidelines with children to avoid possible risk of electric shock or other injuries. Recommend: The game should be periodically examined for conditions that may result in the risk of fire, electrical shock or injury to persons. In the event such conditions exist, the game should not be used until properly repaired. Storage: This product is made from wood-based components and is sensitive to extreme temperatures

Remove all the parts from the box and verify that you have all of the listed parts as shown on the parts list page. Find a clean, level place to begin assembling your Pop-A-Shot game. Like most things in life, putting together your Pop-A-Shot is better when done with a friend.

Required Recommended Nylon head mallet (Not included) - for tapping corners Step ladder or stool 9/16” Wrench (Not included) - for installing rim 9/16” Deep Well Socket (Not included) - for installing rim 2x 7/16” wrench (not included) - for installing backboard to frame

We hope you love your Pop-A-Shot and will let your friends and family (and any review sites) know how you feel. If you do have a problem (and it happens), please let us know first and give us a chance to fix it. Email: [email protected]

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 2/15

SKU# PASCLAS19-02 POP-A-SHOT CLASSIC DUAL FRAME ASSEMBLY

ALL FRAME TUBE PARTS ARE LABELED

T4 T3 T2 T1 F8

R6 R5 F7 R4 S3 F6 R7 S4 S2

F4 B4 S1 F5 F3 B2 B3

F2 B1 F1

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 3/15

SKU# PASCLAS19-02 PARTS LIST

Backboard Rim and Net Ramp and Netting Set Control Panel 2x 1x 1x

AC Adapter Balls Pump Bolt for two rims 1x 7x 1x 8x

Long bolt for Washer for Nut for two rims backboard backboard Nut for backboard 8x 4x 8x 4x

Four-Way Joints 4x

Inspect your box to make sure all parts are included

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 4/15

SKU# PASCLAS19-02 STEP 1 TO BUILD BOTTOM FRAME Connect F1 horizontally into Four-Way Joints on B1 and B3. Connect R1 horizontally into Four-Way Joints on B2 and B4. Connect B1 with B2, and B3 with B4 with Tee Joints. Attach 4-Way Joints to each end of assembled bottom frames.

4-WAY JOINT

BOTTOM FRAME B2 T-JOINT

4-WAY JOINT B4 4-WAY JOINT

B1 TO BUILD TOP FRAME T2 Connect T1 with T2 and B3 T-JOINT connect T3 to T4.

4-WAY JOINT T4

T3 Front Connect F2 vertically into Four-Way Joint on B1. Connect F3 vertically into Four-Way Joint on B3. R2 REAR Rear Connect R2 vertically into Four-Way Joint on B2. R3 Connect R3 vertically into Four-Way Joint on B4. R1 B2 COUPLER

F2 B4

B1 F3

FRONT B3 F1 TAP CORNERS AS YOU BUILD FRAME

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 5/15 SKU# PASCLAS19-02 STEP 2 TO BUILD FRONT FRAME Connect F6 to F2 (Left Side), using Coupler. Connect F7 to F3 (Right Side), using Coupler. Slide F4 and F5 into holes in F2 and F3. Connect 3-Way Elbows to top of F6 and F7. Finish front frame with F8. TAP CORNERS AS YOU BUILD FRAME

3-WAY ELBOW

3-WAY ELBOW F8

F7 COUPLER

F5 COUPLER F2

F3 F1

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 6/15 SKU# PASCLAS19-02 STEP 3 TO BUILD THE BACKBOARD ASSEMBLY Install: Two Bolts go to R4 to right side of Backboard, then two other Bolts go to R5 and install Nuts on each of the Bolts to hold Backboard. Do not tighten the Four Nuts.

TAP CORNERS AS YOU BUILD FRAME

BACK BOARD

R6 R5

TEE JOINT R7 TEE JOINT

Connect the two Tee Joints to R7, then connect it to the bottom of R4 and R5. Now tighten the Nuts to secure the Backboard.

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 7/15 SKU# PASCLAS19-02 TO BUILD REAR FRAME STEP 4 Connect R3 to R1. Connect R2 to R1. Connect R4 to R5 with the Backboard Assembly. TAP CORNERS AS YOU BUILD FRAME

90° ELBOW

Backboard Assembly

R5 R7

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 8/15 SKU# PASCLAS19-02 ADD TOP FRAME AND SIDE SUPPORTS STEP 5 Connect T1, T2, T3 and T4 to frame using 3-Way Elbows on the front and Single Elbows on the rear. Connect S1, S2, S3 and S4 to the 45 ° elbows on the R4 and R5 of the back frame.

SINGLE ELBOW TOP FRAME BARS

3-WAY ELBOW T4 T1

S3 S1

Use a step ladder for safety, where possible.

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 9/13 SKU# PASCLAS19-02 Install Two Rims with hardware using the included Nuts and Bolts; STEP 6 you will need a 9/16” Wrench, a 3/8” Drive Ratchet and a 9/16” Deep Well Socket (not included).

Note: Your sensor and scoreboard are pre-installed. Please make sure the connections are secure.

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 10/15 SKU# PASCLAS19-02 Take the Ball Return Ramp and attach the Velcro Sleeves STEP 7 around the Top Side Tubes. Pull the Velcro under the Lean Bar and wrap around the Horizontal Bar.

VELCRO

Pull the ramp under the Horizontal Tube under the Backboard and attach the tabs to the Bolts of the Backboard. Connect the Velcro Straps around the Rear Vertical Tubes, Middle.

YOU’RE READY TO PLAY!

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 11/15 SKU# PASCLAS19-02 Snap the Control Panel (#21) onto the Horizontal Bar. STEP 7 Thread the Control Panel wire through the hole of the laminated Game Operations “Cheat Sheet” until the Cheat Sheet is next to the Control Panel. Take the Control Panel wire and weave it through the side netting towards the back of the Backboard. Plug the Control Panel wire into the outlet labeled “Control Panel” in the Scoring Unit.

Tip: You’ll find complete game directions and operations in this booklet. The “Cheat Sheet” is intended as a quick handy reference guide

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 12/15 SKU# PASCLAS19-02 Now that you’ve put your Classic Dual together, let’s get started playing!

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 13/15 PASCLAS19-02 CLASSIC DUAL POP-A-SHOT GAME OPERATION

Push GAME until desired Game Number is displayed, then press START to begin.

To turn Game o , press and Hold START.

1. Standard: 2 Players/:30 Announcer and clock will count down to start Bonus: :15 extra at 30 points; :10 extra at 60 points Baskets are 2 points until final :10 when they’re 3 points

2. Solo: 1 Player/:30 Only 1 basket is active Announcer and clock will count down to start Bonus: :15 extra at 30 points; :10 extra at 60 points Baskets are 2 points until final :10 when they’re 3 points

3. Crisscross: 2 Players/:30 Players shoot at their opponent’s basket Announcer and clock will count down to start Bonus: :15 extra at 30 points; :10 extra at 60 points Baskets are 2 points until final :10 when they’re 3 points

4. Skeet Shooting: 1 or 2 Players Announcer says “Shoot”, then have :03 to make basket

5. Sharp Shooter: 1 Player Announcer says “Left” or “Right” and scoreboard indicates “L” or “R”, then have :03 to make a shot in that basket

6. Climbing the Ladder: 2 Players/:30 First basket is 2 points; each subsequent basket is an additional point (3, 4, 5, etc.) If no basket is made within :03, next basket is 2 points Bonus: :15 extra at 30 points; :10 extra at 60 points

7. Overtime: 2 Players/1:00 Baskets are 2 points until final :10 when they’re 3 points Bonus: :15 extra at 30 points; :10 extra at 60 points

8. Sudden Death: 2 Players/:15 Baskets are 2 points until final :10 when they’re 3 points Bonus: :15 extra at 30 points; :10 extra at 60 points

9. Free Play: 1-2 Players/No clock All baskets count 2 points

10. Team: 2 Players /:30 Score displays on both sides Announcer and clock will count down to start Bonus: 15 extra at 30 points; :10 extra at 60 points Baskets are 2 points until final :10 when they’re 3 points

WWW.POP-A-SHOT.NET Pop-A-Shot Classic Dual Page 14/15 SKU# PASCLAS19-02 TROUBLESHOOTING

If your game isn’t powering on • Check that the AC Adapter is plugged into the scoreboard. You can also use 4 AA batteries to power the game.

If one side isn’t counting baskets • Make sure you have chosen a multi-player game (such as Game 1) on your Control Panel. • Make sure the sensors are securely plugged into the correct outlets in the scoreboard (Step 13). • Make sure the sensors are attached level, with the screws tightened all the way. If the sensors are misaligned or angled at all, they will not correctly read the shots (Step 13). • Check the connection between the sensors and the scoreboard (Step 13).

If neither side is counting baskets • Make sure the sensors are securely plugged into the correct outlets in the scoreboard (Step 13). • Make sure the sensors are attached level, with the screws tightened all the way. If the sensors are misaligned or angled at all, they will not correctly read the shots (Step 13). • Check the connection between the sensors and the scoreboard (Step 13). • Make sure the nets are correctly attached to the rims (incorrect placement can block the sensors). The net’s longer loops should go through the hooks of the rim (Step 12).

Please visit www.pop-a-shot.net/support for more troubleshooting tips and hacks.